Commit | Line | Data |
---|---|---|
643f12db | 1 | ThinkPad ACPI Extras Driver |
1da177e4 | 2 | |
643f12db | 3 | Version 0.14 |
54ae1501 | 4 | April 21st, 2007 |
1da177e4 LT |
5 | |
6 | Borislav Deianov <borislav@users.sf.net> | |
38f996ed | 7 | Henrique de Moraes Holschuh <hmh@hmh.eng.br> |
1da177e4 LT |
8 | http://ibm-acpi.sf.net/ |
9 | ||
10 | ||
643f12db HMH |
11 | This is a Linux driver for the IBM and Lenovo ThinkPad laptops. It |
12 | supports various features of these laptops which are accessible | |
13 | through the ACPI and ACPI EC framework, but not otherwise fully | |
14 | supported by the generic Linux ACPI drivers. | |
15 | ||
16 | This driver used to be named ibm-acpi until kernel 2.6.21 and release | |
17 | 0.13-20070314. It used to be in the drivers/acpi tree, but it was | |
18 | moved to the drivers/misc tree and renamed to thinkpad-acpi for kernel | |
19 | 2.6.22, and release 0.14. | |
1da177e4 LT |
20 | |
21 | ||
22 | Status | |
23 | ------ | |
24 | ||
25 | The features currently supported are the following (see below for | |
26 | detailed description): | |
27 | ||
28 | - Fn key combinations | |
29 | - Bluetooth enable and disable | |
837ca6dd | 30 | - video output switching, expansion control |
1da177e4 LT |
31 | - ThinkLight on and off |
32 | - limited docking and undocking | |
33 | - UltraBay eject | |
78f81cc4 BD |
34 | - CMOS control |
35 | - LED control | |
36 | - ACPI sounds | |
37 | - temperature sensors | |
38 | - Experimental: embedded controller register dump | |
24f7ff0a SS |
39 | - LCD brightness control |
40 | - Volume control | |
ecf2a80a | 41 | - Fan control and monitoring: fan speed, fan enable/disable |
28b779d1 | 42 | - Experimental: WAN enable and disable |
1da177e4 LT |
43 | |
44 | A compatibility table by model and feature is maintained on the web | |
45 | site, http://ibm-acpi.sf.net/. I appreciate any success or failure | |
46 | reports, especially if they add to or correct the compatibility table. | |
47 | Please include the following information in your report: | |
48 | ||
49 | - ThinkPad model name | |
50 | - a copy of your DSDT, from /proc/acpi/dsdt | |
643f12db HMH |
51 | - a copy of the output of dmidecode, with serial numbers |
52 | and UUIDs masked off | |
1da177e4 LT |
53 | - which driver features work and which don't |
54 | - the observed behavior of non-working features | |
55 | ||
56 | Any other comments or patches are also more than welcome. | |
57 | ||
58 | ||
59 | Installation | |
60 | ------------ | |
61 | ||
62 | If you are compiling this driver as included in the Linux kernel | |
643f12db HMH |
63 | sources, simply enable the CONFIG_THINKPAD_ACPI option, and optionally |
64 | enable the CONFIG_THINKPAD_ACPI_BAY option if you want the | |
65 | thinkpad-specific bay functionality. | |
1da177e4 LT |
66 | |
67 | Features | |
68 | -------- | |
69 | ||
54ae1501 HMH |
70 | The driver exports two different interfaces to userspace, which can be |
71 | used to access the features it provides. One is a legacy procfs-based | |
72 | interface, which will be removed at some time in the distant future. | |
73 | The other is a new sysfs-based interface which is not complete yet. | |
74 | ||
75 | The procfs interface creates the /proc/acpi/ibm directory. There is a | |
76 | file under that directory for each feature it supports. The procfs | |
77 | interface is mostly frozen, and will change very little if at all: it | |
78 | will not be extended to add any new functionality in the driver, instead | |
79 | all new functionality will be implemented on the sysfs interface. | |
80 | ||
81 | The sysfs interface tries to blend in the generic Linux sysfs subsystems | |
82 | and classes as much as possible. Since some of these subsystems are not | |
83 | yet ready or stabilized, it is expected that this interface will change, | |
84 | and any and all userspace programs must deal with it. | |
85 | ||
86 | ||
87 | Notes about the sysfs interface: | |
88 | ||
89 | Unlike what was done with the procfs interface, correctness when talking | |
90 | to the sysfs interfaces will be enforced, as will correctness in the | |
91 | thinkpad-acpi's implementation of sysfs interfaces. | |
92 | ||
93 | Also, any bugs in the thinkpad-acpi sysfs driver code or in the | |
94 | thinkpad-acpi's implementation of the sysfs interfaces will be fixed for | |
95 | maximum correctness, even if that means changing an interface in | |
96 | non-compatible ways. As these interfaces mature both in the kernel and | |
97 | in thinkpad-acpi, such changes should become quite rare. | |
98 | ||
99 | Applications interfacing to the thinkpad-acpi sysfs interfaces must | |
100 | follow all sysfs guidelines and correctly process all errors (the sysfs | |
101 | interface makes extensive use of errors). File descriptors and open / | |
102 | close operations to the sysfs inodes must also be properly implemented. | |
1da177e4 | 103 | |
176750d6 HMH |
104 | The version of thinkpad-acpi's sysfs interface is exported by the driver |
105 | as a driver attribute (see below). | |
106 | ||
107 | Sysfs driver attributes are on the driver's sysfs attribute space, | |
108 | for 2.6.20 this is /sys/bus/platform/drivers/thinkpad-acpi/. | |
109 | ||
110 | Sysfs device attributes are on the driver's sysfs attribute space, | |
111 | for 2.6.20 this is /sys/devices/platform/thinkpad-acpi/. | |
112 | ||
113 | Driver version | |
114 | -------------- | |
115 | ||
116 | procfs: /proc/acpi/ibm/driver | |
117 | sysfs driver attribute: version | |
1da177e4 LT |
118 | |
119 | The driver name and version. No commands can be written to this file. | |
120 | ||
176750d6 HMH |
121 | Sysfs interface version |
122 | ----------------------- | |
123 | ||
124 | sysfs driver attribute: interface_version | |
125 | ||
126 | Version of the thinkpad-acpi sysfs interface, as an unsigned long | |
127 | (output in hex format: 0xAAAABBCC), where: | |
128 | AAAA - major revision | |
129 | BB - minor revision | |
130 | CC - bugfix revision | |
131 | ||
132 | The sysfs interface version changelog for the driver can be found at the | |
133 | end of this document. Changes to the sysfs interface done by the kernel | |
134 | subsystems are not documented here, nor are they tracked by this | |
135 | attribute. | |
136 | ||
94b08713 HMH |
137 | Changes to the thinkpad-acpi sysfs interface are only considered |
138 | non-experimental when they are submitted to Linux mainline, at which | |
139 | point the changes in this interface are documented and interface_version | |
140 | may be updated. If you are using any thinkpad-acpi features not yet | |
141 | sent to mainline for merging, you do so on your own risk: these features | |
142 | may disappear, or be implemented in a different and incompatible way by | |
143 | the time they are merged in Linux mainline. | |
144 | ||
145 | Changes that are backwards-compatible by nature (e.g. the addition of | |
146 | attributes that do not change the way the other attributes work) do not | |
147 | always warrant an update of interface_version. Therefore, one must | |
148 | expect that an attribute might not be there, and deal with it properly | |
149 | (an attribute not being there *is* a valid way to make it clear that a | |
150 | feature is not available in sysfs). | |
151 | ||
a0416420 HMH |
152 | Hot keys |
153 | -------- | |
154 | ||
155 | procfs: /proc/acpi/ibm/hotkey | |
cc4c24e1 | 156 | sysfs device attribute: hotkey_* |
1da177e4 | 157 | |
1a343760 HMH |
158 | In a ThinkPad, the ACPI HKEY handler is responsible for comunicating |
159 | some important events and also keyboard hot key presses to the operating | |
160 | system. Enabling the hotkey functionality of thinkpad-acpi signals the | |
161 | firmware that such a driver is present, and modifies how the ThinkPad | |
162 | firmware will behave in many situations. | |
163 | ||
164 | When the hotkey feature is enabled and the hot key mask is set (see | |
165 | below), the various hot keys either generate ACPI events in the | |
1da177e4 LT |
166 | following format: |
167 | ||
168 | ibm/hotkey HKEY 00000080 0000xxxx | |
169 | ||
1a343760 HMH |
170 | or events over the input layer. The input layer support accepts the |
171 | standard IOCTLs to remap the keycodes assigned to each hotkey. | |
6a38abbf HMH |
172 | |
173 | When the input device is open, the driver will suppress any ACPI hot key | |
174 | events that get translated into a meaningful input layer event, in order | |
175 | to avoid sending duplicate events to userspace. Hot keys that are | |
1a343760 HMH |
176 | mapped to KEY_RESERVED in the keymap are not translated, and will always |
177 | generate an ACPI ibm/hotkey HKEY event, and no input layer events. | |
178 | ||
179 | The hot key bit mask allows some control over which hot keys generate | |
180 | events. If a key is "masked" (bit set to 0 in the mask), the firmware | |
181 | will handle it. If it is "unmasked", it signals the firmware that | |
182 | thinkpad-acpi would prefer to handle it, if the firmware would be so | |
183 | kind to allow it (and it often doesn't!). | |
184 | ||
185 | Not all bits in the mask can be modified. Not all bits that can be | |
186 | modified do anything. Not all hot keys can be individually controlled | |
187 | by the mask. Some models do not support the mask at all, and in those | |
188 | models, hot keys cannot be controlled individually. The behaviour of | |
189 | the mask is, therefore, higly dependent on the ThinkPad model. | |
190 | ||
191 | Note that unmasking some keys prevents their default behavior. For | |
192 | example, if Fn+F5 is unmasked, that key will no longer enable/disable | |
193 | Bluetooth by itself. | |
194 | ||
195 | Note also that not all Fn key combinations are supported through ACPI. | |
196 | For example, on the X40, the brightness, volume and "Access IBM" buttons | |
197 | do not generate ACPI events even with this driver. They *can* be used | |
198 | through the "ThinkPad Buttons" utility, see http://www.nongnu.org/tpb/ | |
1da177e4 | 199 | |
a0416420 HMH |
200 | procfs notes: |
201 | ||
202 | The following commands can be written to the /proc/acpi/ibm/hotkey file: | |
203 | ||
204 | echo enable > /proc/acpi/ibm/hotkey -- enable the hot keys feature | |
205 | echo disable > /proc/acpi/ibm/hotkey -- disable the hot keys feature | |
ae92bd17 HMH |
206 | echo 0xffffffff > /proc/acpi/ibm/hotkey -- enable all hot keys |
207 | echo 0 > /proc/acpi/ibm/hotkey -- disable all possible hot keys | |
208 | ... any other 8-hex-digit mask ... | |
a0416420 HMH |
209 | echo reset > /proc/acpi/ibm/hotkey -- restore the original mask |
210 | ||
211 | sysfs notes: | |
212 | ||
cc4c24e1 | 213 | hotkey_bios_enabled: |
a0416420 HMH |
214 | Returns the status of the hot keys feature when |
215 | thinkpad-acpi was loaded. Upon module unload, the hot | |
216 | key feature status will be restored to this value. | |
217 | ||
218 | 0: hot keys were disabled | |
1a343760 | 219 | 1: hot keys were enabled (unusual) |
a0416420 | 220 | |
cc4c24e1 | 221 | hotkey_bios_mask: |
a0416420 HMH |
222 | Returns the hot keys mask when thinkpad-acpi was loaded. |
223 | Upon module unload, the hot keys mask will be restored | |
224 | to this value. | |
225 | ||
cc4c24e1 | 226 | hotkey_enable: |
a0416420 HMH |
227 | Enables/disables the hot keys feature, and reports |
228 | current status of the hot keys feature. | |
229 | ||
230 | 0: disables the hot keys feature / feature disabled | |
231 | 1: enables the hot keys feature / feature enabled | |
232 | ||
cc4c24e1 | 233 | hotkey_mask: |
1a343760 HMH |
234 | bit mask to enable driver-handling and ACPI event |
235 | generation for each hot key (see above). Returns the | |
236 | current status of the hot keys mask, and allows one to | |
237 | modify it. | |
a0416420 | 238 | |
9b010de5 HMH |
239 | hotkey_all_mask: |
240 | bit mask that should enable event reporting for all | |
241 | supported hot keys, when echoed to hotkey_mask above. | |
242 | Unless you know which events need to be handled | |
243 | passively (because the firmware *will* handle them | |
244 | anyway), do *not* use hotkey_all_mask. Use | |
245 | hotkey_recommended_mask, instead. You have been warned. | |
246 | ||
247 | hotkey_recommended_mask: | |
248 | bit mask that should enable event reporting for all | |
1a343760 HMH |
249 | supported hot keys, except those which are always |
250 | handled by the firmware anyway. Echo it to | |
251 | hotkey_mask above, to use. | |
9b010de5 | 252 | |
74941a69 HMH |
253 | hotkey_radio_sw: |
254 | if the ThinkPad has a hardware radio switch, this | |
255 | attribute will read 0 if the switch is in the "radios | |
256 | disabled" postition, and 1 if the switch is in the | |
257 | "radios enabled" position. | |
258 | ||
6a38abbf HMH |
259 | input layer notes: |
260 | ||
261 | A Hot key is mapped to a single input layer EV_KEY event, possibly | |
262 | followed by an EV_MSC MSC_SCAN event that shall contain that key's scan | |
263 | code. An EV_SYN event will always be generated to mark the end of the | |
264 | event block. | |
265 | ||
266 | Do not use the EV_MSC MSC_SCAN events to process keys. They are to be | |
267 | used as a helper to remap keys, only. They are particularly useful when | |
268 | remapping KEY_UNKNOWN keys. | |
269 | ||
270 | The events are available in an input device, with the following id: | |
271 | ||
272 | Bus: BUS_HOST | |
273 | vendor: 0x1014 (PCI_VENDOR_ID_IBM) | |
274 | product: 0x5054 ("TP") | |
275 | version: 0x4101 | |
276 | ||
277 | The version will have its LSB incremented if the keymap changes in a | |
278 | backwards-compatible way. The MSB shall always be 0x41 for this input | |
279 | device. If the MSB is not 0x41, do not use the device as described in | |
280 | this section, as it is either something else (e.g. another input device | |
281 | exported by a thinkpad driver, such as HDAPS) or its functionality has | |
282 | been changed in a non-backwards compatible way. | |
283 | ||
284 | Adding other event types for other functionalities shall be considered a | |
285 | backwards-compatible change for this input device. | |
286 | ||
287 | Thinkpad-acpi Hot Key event map (version 0x4101): | |
288 | ||
289 | ACPI Scan | |
290 | event code Key Notes | |
291 | ||
292 | 0x1001 0x00 FN+F1 - | |
293 | 0x1002 0x01 FN+F2 - | |
294 | ||
295 | 0x1003 0x02 FN+F3 Many models always report this | |
296 | hot key, even with hot keys | |
297 | disabled or with Fn+F3 masked | |
298 | off | |
299 | ||
300 | 0x1004 0x03 FN+F4 Sleep button (ACPI sleep button | |
301 | semanthics, i.e. sleep-to-RAM). | |
302 | It is always generate some kind | |
303 | of event, either the hot key | |
304 | event or a ACPI sleep button | |
305 | event. The firmware may | |
306 | refuse to generate further FN+F4 | |
307 | key presses until a S3 or S4 ACPI | |
308 | sleep cycle is performed or some | |
309 | time passes. | |
310 | ||
311 | 0x1005 0x04 FN+F5 Radio. Enables/disables | |
312 | the internal BlueTooth hardware | |
313 | and W-WAN card if left in control | |
314 | of the firmware. Does not affect | |
315 | the WLAN card. | |
316 | ||
317 | 0x1006 0x05 FN+F6 - | |
318 | ||
319 | 0x1007 0x06 FN+F7 Video output cycle. | |
320 | Do you feel lucky today? | |
321 | ||
322 | 0x1008 0x07 FN+F8 - | |
323 | .. .. .. | |
324 | 0x100B 0x0A FN+F11 - | |
325 | ||
326 | 0x100C 0x0B FN+F12 Sleep to disk. You are always | |
327 | supposed to handle it yourself, | |
328 | either through the ACPI event, | |
329 | or through a hotkey event. | |
330 | The firmware may refuse to | |
331 | generate further FN+F4 key | |
332 | press events until a S3 or S4 | |
333 | ACPI sleep cycle is performed, | |
334 | or some time passes. | |
335 | ||
336 | 0x100D 0x0C FN+BACKSPACE - | |
337 | 0x100E 0x0D FN+INSERT - | |
338 | 0x100F 0x0E FN+DELETE - | |
339 | ||
340 | 0x1010 0x0F FN+HOME Brightness up. This key is | |
341 | always handled by the firmware, | |
342 | even when unmasked. Just leave | |
343 | it alone. | |
344 | 0x1011 0x10 FN+END Brightness down. This key is | |
345 | always handled by the firmware, | |
346 | even when unmasked. Just leave | |
347 | it alone. | |
348 | 0x1012 0x11 FN+PGUP Thinklight toggle. This key is | |
349 | always handled by the firmware, | |
350 | even when unmasked. | |
351 | ||
352 | 0x1013 0x12 FN+PGDOWN - | |
353 | ||
354 | 0x1014 0x13 FN+SPACE Zoom key | |
355 | ||
356 | 0x1015 0x14 VOLUME UP Internal mixer volume up. This | |
357 | key is always handled by the | |
358 | firmware, even when unmasked. | |
359 | 0x1016 0x15 VOLUME DOWN Internal mixer volume up. This | |
360 | key is always handled by the | |
361 | firmware, even when unmasked. | |
362 | 0x1017 0x16 MUTE Mute internal mixer. This | |
363 | key is always handled by the | |
364 | firmware, even when unmasked. | |
365 | ||
366 | 0x1018 0x17 THINKPAD Thinkpad/Access IBM/Lenovo key | |
367 | ||
368 | 0x1019 0x18 unknown | |
369 | .. .. .. | |
370 | 0x1020 0x1F unknown | |
371 | ||
372 | The ThinkPad firmware does not allow one to differentiate when most hot | |
373 | keys are pressed or released (either that, or we don't know how to, yet). | |
374 | For these keys, the driver generates a set of events for a key press and | |
375 | immediately issues the same set of events for a key release. It is | |
376 | unknown by the driver if the ThinkPad firmware triggered these events on | |
377 | hot key press or release, but the firmware will do it for either one, not | |
378 | both. | |
379 | ||
380 | If a key is mapped to KEY_RESERVED, it generates no input events at all, | |
381 | and it may generate a legacy thinkpad-acpi ACPI hotkey event. | |
382 | ||
383 | If a key is mapped to KEY_UNKNOWN, it generates an input event that | |
384 | includes an scan code, and it may also generate a legacy thinkpad-acpi | |
385 | ACPI hotkey event. | |
386 | ||
387 | If a key is mapped to anything else, it will only generate legacy | |
388 | thinkpad-acpi ACPI hotkey events if nobody has opened the input device. | |
389 | ||
6a38abbf HMH |
390 | Non hot-key ACPI HKEY event map: |
391 | 0x5001 Lid closed | |
392 | 0x5002 Lid opened | |
393 | 0x7000 Radio Switch may have changed state | |
394 | ||
a0416420 | 395 | |
d3a6ade4 HMH |
396 | Bluetooth |
397 | --------- | |
1da177e4 | 398 | |
d3a6ade4 | 399 | procfs: /proc/acpi/ibm/bluetooth |
cc4c24e1 | 400 | sysfs device attribute: bluetooth_enable |
d3a6ade4 HMH |
401 | |
402 | This feature shows the presence and current state of a ThinkPad | |
403 | Bluetooth device in the internal ThinkPad CDC slot. | |
404 | ||
405 | Procfs notes: | |
406 | ||
407 | If Bluetooth is installed, the following commands can be used: | |
1da177e4 LT |
408 | |
409 | echo enable > /proc/acpi/ibm/bluetooth | |
410 | echo disable > /proc/acpi/ibm/bluetooth | |
411 | ||
d3a6ade4 HMH |
412 | Sysfs notes: |
413 | ||
414 | If the Bluetooth CDC card is installed, it can be enabled / | |
cc4c24e1 | 415 | disabled through the "bluetooth_enable" thinkpad-acpi device |
d3a6ade4 HMH |
416 | attribute, and its current status can also be queried. |
417 | ||
418 | enable: | |
419 | 0: disables Bluetooth / Bluetooth is disabled | |
420 | 1: enables Bluetooth / Bluetooth is enabled. | |
421 | ||
422 | Note: this interface will be probably be superseeded by the | |
cc4c24e1 | 423 | generic rfkill class, so it is NOT to be considered stable yet. |
d3a6ade4 | 424 | |
1da177e4 LT |
425 | Video output control -- /proc/acpi/ibm/video |
426 | -------------------------------------------- | |
427 | ||
428 | This feature allows control over the devices used for video output - | |
429 | LCD, CRT or DVI (if available). The following commands are available: | |
430 | ||
431 | echo lcd_enable > /proc/acpi/ibm/video | |
432 | echo lcd_disable > /proc/acpi/ibm/video | |
433 | echo crt_enable > /proc/acpi/ibm/video | |
434 | echo crt_disable > /proc/acpi/ibm/video | |
435 | echo dvi_enable > /proc/acpi/ibm/video | |
436 | echo dvi_disable > /proc/acpi/ibm/video | |
437 | echo auto_enable > /proc/acpi/ibm/video | |
438 | echo auto_disable > /proc/acpi/ibm/video | |
439 | echo expand_toggle > /proc/acpi/ibm/video | |
440 | echo video_switch > /proc/acpi/ibm/video | |
441 | ||
442 | Each video output device can be enabled or disabled individually. | |
443 | Reading /proc/acpi/ibm/video shows the status of each device. | |
444 | ||
445 | Automatic video switching can be enabled or disabled. When automatic | |
446 | video switching is enabled, certain events (e.g. opening the lid, | |
447 | docking or undocking) cause the video output device to change | |
448 | automatically. While this can be useful, it also causes flickering | |
449 | and, on the X40, video corruption. By disabling automatic switching, | |
450 | the flickering or video corruption can be avoided. | |
451 | ||
452 | The video_switch command cycles through the available video outputs | |
78f81cc4 | 453 | (it simulates the behavior of Fn-F7). |
1da177e4 LT |
454 | |
455 | Video expansion can be toggled through this feature. This controls | |
456 | whether the display is expanded to fill the entire LCD screen when a | |
457 | mode with less than full resolution is used. Note that the current | |
458 | video expansion status cannot be determined through this feature. | |
459 | ||
460 | Note that on many models (particularly those using Radeon graphics | |
461 | chips) the X driver configures the video card in a way which prevents | |
462 | Fn-F7 from working. This also disables the video output switching | |
463 | features of this driver, as it uses the same ACPI methods as | |
464 | Fn-F7. Video switching on the console should still work. | |
465 | ||
78f81cc4 BD |
466 | UPDATE: There's now a patch for the X.org Radeon driver which |
467 | addresses this issue. Some people are reporting success with the patch | |
468 | while others are still having problems. For more information: | |
469 | ||
470 | https://bugs.freedesktop.org/show_bug.cgi?id=2000 | |
471 | ||
1da177e4 LT |
472 | ThinkLight control -- /proc/acpi/ibm/light |
473 | ------------------------------------------ | |
474 | ||
475 | The current status of the ThinkLight can be found in this file. A few | |
476 | models which do not make the status available will show it as | |
477 | "unknown". The available commands are: | |
478 | ||
479 | echo on > /proc/acpi/ibm/light | |
480 | echo off > /proc/acpi/ibm/light | |
481 | ||
78f81cc4 | 482 | Docking / undocking -- /proc/acpi/ibm/dock |
1da177e4 LT |
483 | ------------------------------------------ |
484 | ||
485 | Docking and undocking (e.g. with the X4 UltraBase) requires some | |
486 | actions to be taken by the operating system to safely make or break | |
487 | the electrical connections with the dock. | |
488 | ||
489 | The docking feature of this driver generates the following ACPI events: | |
490 | ||
491 | ibm/dock GDCK 00000003 00000001 -- eject request | |
492 | ibm/dock GDCK 00000003 00000002 -- undocked | |
493 | ibm/dock GDCK 00000000 00000003 -- docked | |
494 | ||
495 | NOTE: These events will only be generated if the laptop was docked | |
496 | when originally booted. This is due to the current lack of support for | |
497 | hot plugging of devices in the Linux ACPI framework. If the laptop was | |
498 | booted while not in the dock, the following message is shown in the | |
78f81cc4 BD |
499 | logs: |
500 | ||
643f12db | 501 | Mar 17 01:42:34 aero kernel: thinkpad_acpi: dock device not present |
78f81cc4 BD |
502 | |
503 | In this case, no dock-related events are generated but the dock and | |
504 | undock commands described below still work. They can be executed | |
505 | manually or triggered by Fn key combinations (see the example acpid | |
506 | configuration files included in the driver tarball package available | |
507 | on the web site). | |
1da177e4 LT |
508 | |
509 | When the eject request button on the dock is pressed, the first event | |
510 | above is generated. The handler for this event should issue the | |
511 | following command: | |
512 | ||
513 | echo undock > /proc/acpi/ibm/dock | |
514 | ||
515 | After the LED on the dock goes off, it is safe to eject the laptop. | |
516 | Note: if you pressed this key by mistake, go ahead and eject the | |
517 | laptop, then dock it back in. Otherwise, the dock may not function as | |
518 | expected. | |
519 | ||
520 | When the laptop is docked, the third event above is generated. The | |
521 | handler for this event should issue the following command to fully | |
522 | enable the dock: | |
523 | ||
524 | echo dock > /proc/acpi/ibm/dock | |
525 | ||
526 | The contents of the /proc/acpi/ibm/dock file shows the current status | |
527 | of the dock, as provided by the ACPI framework. | |
528 | ||
529 | The docking support in this driver does not take care of enabling or | |
530 | disabling any other devices you may have attached to the dock. For | |
531 | example, a CD drive plugged into the UltraBase needs to be disabled or | |
532 | enabled separately. See the provided example acpid configuration files | |
533 | for how this can be accomplished. | |
534 | ||
535 | There is no support yet for PCI devices that may be attached to a | |
536 | docking station, e.g. in the ThinkPad Dock II. The driver currently | |
537 | does not recognize, enable or disable such devices. This means that | |
538 | the only docking stations currently supported are the X-series | |
539 | UltraBase docks and "dumb" port replicators like the Mini Dock (the | |
540 | latter don't need any ACPI support, actually). | |
541 | ||
78f81cc4 | 542 | UltraBay eject -- /proc/acpi/ibm/bay |
1da177e4 LT |
543 | ------------------------------------ |
544 | ||
545 | Inserting or ejecting an UltraBay device requires some actions to be | |
546 | taken by the operating system to safely make or break the electrical | |
547 | connections with the device. | |
548 | ||
549 | This feature generates the following ACPI events: | |
550 | ||
551 | ibm/bay MSTR 00000003 00000000 -- eject request | |
552 | ibm/bay MSTR 00000001 00000000 -- eject lever inserted | |
553 | ||
554 | NOTE: These events will only be generated if the UltraBay was present | |
555 | when the laptop was originally booted (on the X series, the UltraBay | |
556 | is in the dock, so it may not be present if the laptop was undocked). | |
557 | This is due to the current lack of support for hot plugging of devices | |
558 | in the Linux ACPI framework. If the laptop was booted without the | |
78f81cc4 BD |
559 | UltraBay, the following message is shown in the logs: |
560 | ||
643f12db | 561 | Mar 17 01:42:34 aero kernel: thinkpad_acpi: bay device not present |
78f81cc4 BD |
562 | |
563 | In this case, no bay-related events are generated but the eject | |
1da177e4 LT |
564 | command described below still works. It can be executed manually or |
565 | triggered by a hot key combination. | |
566 | ||
567 | Sliding the eject lever generates the first event shown above. The | |
568 | handler for this event should take whatever actions are necessary to | |
569 | shut down the device in the UltraBay (e.g. call idectl), then issue | |
570 | the following command: | |
571 | ||
572 | echo eject > /proc/acpi/ibm/bay | |
573 | ||
574 | After the LED on the UltraBay goes off, it is safe to pull out the | |
575 | device. | |
576 | ||
577 | When the eject lever is inserted, the second event above is | |
578 | generated. The handler for this event should take whatever actions are | |
579 | necessary to enable the UltraBay device (e.g. call idectl). | |
580 | ||
581 | The contents of the /proc/acpi/ibm/bay file shows the current status | |
582 | of the UltraBay, as provided by the ACPI framework. | |
583 | ||
78f81cc4 BD |
584 | EXPERIMENTAL warm eject support on the 600e/x, A22p and A3x (To use |
585 | this feature, you need to supply the experimental=1 parameter when | |
586 | loading the module): | |
587 | ||
588 | These models do not have a button near the UltraBay device to request | |
589 | a hot eject but rather require the laptop to be put to sleep | |
590 | (suspend-to-ram) before the bay device is ejected or inserted). | |
591 | The sequence of steps to eject the device is as follows: | |
592 | ||
593 | echo eject > /proc/acpi/ibm/bay | |
594 | put the ThinkPad to sleep | |
595 | remove the drive | |
596 | resume from sleep | |
597 | cat /proc/acpi/ibm/bay should show that the drive was removed | |
598 | ||
599 | On the A3x, both the UltraBay 2000 and UltraBay Plus devices are | |
600 | supported. Use "eject2" instead of "eject" for the second bay. | |
1da177e4 | 601 | |
78f81cc4 BD |
602 | Note: the UltraBay eject support on the 600e/x, A22p and A3x is |
603 | EXPERIMENTAL and may not work as expected. USE WITH CAUTION! | |
1da177e4 | 604 | |
b616004c HMH |
605 | CMOS control |
606 | ------------ | |
607 | ||
608 | procfs: /proc/acpi/ibm/cmos | |
609 | sysfs device attribute: cmos_command | |
1da177e4 | 610 | |
d54b7d7f HMH |
611 | This feature is mostly used internally by the ACPI firmware to keep the legacy |
612 | CMOS NVRAM bits in sync with the current machine state, and to record this | |
613 | state so that the ThinkPad will retain such settings across reboots. | |
614 | ||
615 | Some of these commands actually perform actions in some ThinkPad models, but | |
616 | this is expected to disappear more and more in newer models. As an example, in | |
617 | a T43 and in a X40, commands 12 and 13 still control the ThinkLight state for | |
618 | real, but commands 0 to 2 don't control the mixer anymore (they have been | |
619 | phased out) and just update the NVRAM. | |
1da177e4 | 620 | |
b616004c HMH |
621 | The range of valid cmos command numbers is 0 to 21, but not all have an |
622 | effect and the behavior varies from model to model. Here is the behavior | |
623 | on the X40 (tpb is the ThinkPad Buttons utility): | |
1da177e4 | 624 | |
d54b7d7f HMH |
625 | 0 - Related to "Volume down" key press |
626 | 1 - Related to "Volume up" key press | |
627 | 2 - Related to "Mute on" key press | |
628 | 3 - Related to "Access IBM" key press | |
629 | 4 - Related to "LCD brightness up" key pess | |
630 | 5 - Related to "LCD brightness down" key press | |
631 | 11 - Related to "toggle screen expansion" key press/function | |
632 | 12 - Related to "ThinkLight on" | |
633 | 13 - Related to "ThinkLight off" | |
634 | 14 - Related to "ThinkLight" key press (toggle thinklight) | |
1da177e4 | 635 | |
b616004c | 636 | The cmos command interface is prone to firmware split-brain problems, as |
d54b7d7f HMH |
637 | in newer ThinkPads it is just a compatibility layer. Do not use it, it is |
638 | exported just as a debug tool. | |
b616004c | 639 | |
78f81cc4 BD |
640 | LED control -- /proc/acpi/ibm/led |
641 | --------------------------------- | |
1da177e4 LT |
642 | |
643 | Some of the LED indicators can be controlled through this feature. The | |
644 | available commands are: | |
645 | ||
78f81cc4 BD |
646 | echo '<led number> on' >/proc/acpi/ibm/led |
647 | echo '<led number> off' >/proc/acpi/ibm/led | |
648 | echo '<led number> blink' >/proc/acpi/ibm/led | |
1da177e4 | 649 | |
78f81cc4 BD |
650 | The <led number> range is 0 to 7. The set of LEDs that can be |
651 | controlled varies from model to model. Here is the mapping on the X40: | |
1da177e4 LT |
652 | |
653 | 0 - power | |
654 | 1 - battery (orange) | |
655 | 2 - battery (green) | |
656 | 3 - UltraBase | |
657 | 4 - UltraBay | |
658 | 7 - standby | |
659 | ||
660 | All of the above can be turned on and off and can be made to blink. | |
661 | ||
78f81cc4 BD |
662 | ACPI sounds -- /proc/acpi/ibm/beep |
663 | ---------------------------------- | |
1da177e4 LT |
664 | |
665 | The BEEP method is used internally by the ACPI firmware to provide | |
78f81cc4 | 666 | audible alerts in various situations. This feature allows the same |
1da177e4 LT |
667 | sounds to be triggered manually. |
668 | ||
669 | The commands are non-negative integer numbers: | |
670 | ||
78f81cc4 | 671 | echo <number> >/proc/acpi/ibm/beep |
1da177e4 | 672 | |
78f81cc4 BD |
673 | The valid <number> range is 0 to 17. Not all numbers trigger sounds |
674 | and the sounds vary from model to model. Here is the behavior on the | |
675 | X40: | |
1da177e4 | 676 | |
78f81cc4 BD |
677 | 0 - stop a sound in progress (but use 17 to stop 16) |
678 | 2 - two beeps, pause, third beep ("low battery") | |
1da177e4 | 679 | 3 - single beep |
78f81cc4 | 680 | 4 - high, followed by low-pitched beep ("unable") |
1da177e4 | 681 | 5 - single beep |
78f81cc4 | 682 | 6 - very high, followed by high-pitched beep ("AC/DC") |
1da177e4 LT |
683 | 7 - high-pitched beep |
684 | 9 - three short beeps | |
685 | 10 - very long beep | |
686 | 12 - low-pitched beep | |
78f81cc4 BD |
687 | 15 - three high-pitched beeps repeating constantly, stop with 0 |
688 | 16 - one medium-pitched beep repeating constantly, stop with 17 | |
689 | 17 - stop 16 | |
690 | ||
2c37aa4e HMH |
691 | Temperature sensors |
692 | ------------------- | |
693 | ||
694 | procfs: /proc/acpi/ibm/thermal | |
695 | sysfs device attributes: (hwmon) temp*_input | |
78f81cc4 BD |
696 | |
697 | Most ThinkPads include six or more separate temperature sensors but | |
698 | only expose the CPU temperature through the standard ACPI methods. | |
60eb0b35 HMH |
699 | This feature shows readings from up to eight different sensors on older |
700 | ThinkPads, and it has experimental support for up to sixteen different | |
2c37aa4e | 701 | sensors on newer ThinkPads. |
60eb0b35 HMH |
702 | |
703 | EXPERIMENTAL: The 16-sensors feature is marked EXPERIMENTAL because the | |
704 | implementation directly accesses hardware registers and may not work as | |
705 | expected. USE WITH CAUTION! To use this feature, you need to supply the | |
706 | experimental=1 parameter when loading the module. When EXPERIMENTAL | |
707 | mode is enabled, reading the first 8 sensors on newer ThinkPads will | |
708 | also use an new experimental thermal sensor access mode. | |
709 | ||
710 | For example, on the X40, a typical output may be: | |
78f81cc4 BD |
711 | temperatures: 42 42 45 41 36 -128 33 -128 |
712 | ||
60eb0b35 HMH |
713 | EXPERIMENTAL: On the T43/p, a typical output may be: |
714 | temperatures: 48 48 36 52 38 -128 31 -128 48 52 48 -128 -128 -128 -128 -128 | |
715 | ||
716 | The mapping of thermal sensors to physical locations varies depending on | |
717 | system-board model (and thus, on ThinkPad model). | |
718 | ||
719 | http://thinkwiki.org/wiki/Thermal_Sensors is a public wiki page that | |
720 | tries to track down these locations for various models. | |
721 | ||
722 | Most (newer?) models seem to follow this pattern: | |
78f81cc4 BD |
723 | |
724 | 1: CPU | |
60eb0b35 HMH |
725 | 2: (depends on model) |
726 | 3: (depends on model) | |
78f81cc4 | 727 | 4: GPU |
60eb0b35 HMH |
728 | 5: Main battery: main sensor |
729 | 6: Bay battery: main sensor | |
730 | 7: Main battery: secondary sensor | |
731 | 8: Bay battery: secondary sensor | |
732 | 9-15: (depends on model) | |
733 | ||
734 | For the R51 (source: Thomas Gruber): | |
735 | 2: Mini-PCI | |
736 | 3: Internal HDD | |
737 | ||
738 | For the T43, T43/p (source: Shmidoax/Thinkwiki.org) | |
739 | http://thinkwiki.org/wiki/Thermal_Sensors#ThinkPad_T43.2C_T43p | |
740 | 2: System board, left side (near PCMCIA slot), reported as HDAPS temp | |
741 | 3: PCMCIA slot | |
742 | 9: MCH (northbridge) to DRAM Bus | |
b8b26402 HMH |
743 | 10: Clock-generator, mini-pci card and ICH (southbridge), under Mini-PCI |
744 | card, under touchpad | |
60eb0b35 | 745 | 11: Power regulator, underside of system board, below F2 key |
78f81cc4 | 746 | |
88679a15 HMH |
747 | The A31 has a very atypical layout for the thermal sensors |
748 | (source: Milos Popovic, http://thinkwiki.org/wiki/Thermal_Sensors#ThinkPad_A31) | |
749 | 1: CPU | |
750 | 2: Main Battery: main sensor | |
751 | 3: Power Converter | |
752 | 4: Bay Battery: main sensor | |
753 | 5: MCH (northbridge) | |
754 | 6: PCMCIA/ambient | |
755 | 7: Main Battery: secondary sensor | |
756 | 8: Bay Battery: secondary sensor | |
757 | ||
78f81cc4 | 758 | |
2c37aa4e HMH |
759 | Procfs notes: |
760 | Readings from sensors that are not available return -128. | |
761 | No commands can be written to this file. | |
762 | ||
763 | Sysfs notes: | |
764 | Sensors that are not available return the ENXIO error. This | |
765 | status may change at runtime, as there are hotplug thermal | |
766 | sensors, like those inside the batteries and docks. | |
767 | ||
768 | thinkpad-acpi thermal sensors are reported through the hwmon | |
769 | subsystem, and follow all of the hwmon guidelines at | |
770 | Documentation/hwmon. | |
771 | ||
772 | ||
d6bc8ac9 | 773 | EXPERIMENTAL: Embedded controller register dump -- /proc/acpi/ibm/ecdump |
78f81cc4 BD |
774 | ------------------------------------------------------------------------ |
775 | ||
776 | This feature is marked EXPERIMENTAL because the implementation | |
777 | directly accesses hardware registers and may not work as expected. USE | |
778 | WITH CAUTION! To use this feature, you need to supply the | |
779 | experimental=1 parameter when loading the module. | |
780 | ||
781 | This feature dumps the values of 256 embedded controller | |
782 | registers. Values which have changed since the last time the registers | |
783 | were dumped are marked with a star: | |
784 | ||
837ca6dd | 785 | [root@x40 ibm-acpi]# cat /proc/acpi/ibm/ecdump |
78f81cc4 BD |
786 | EC +00 +01 +02 +03 +04 +05 +06 +07 +08 +09 +0a +0b +0c +0d +0e +0f |
787 | EC 0x00: a7 47 87 01 fe 96 00 08 01 00 cb 00 00 00 40 00 | |
788 | EC 0x10: 00 00 ff ff f4 3c 87 09 01 ff 42 01 ff ff 0d 00 | |
789 | EC 0x20: 00 00 00 00 00 00 00 00 00 00 00 03 43 00 00 80 | |
790 | EC 0x30: 01 07 1a 00 30 04 00 00 *85 00 00 10 00 50 00 00 | |
791 | EC 0x40: 00 00 00 00 00 00 14 01 00 04 00 00 00 00 00 00 | |
792 | EC 0x50: 00 c0 02 0d 00 01 01 02 02 03 03 03 03 *bc *02 *bc | |
793 | EC 0x60: *02 *bc *02 00 00 00 00 00 00 00 00 00 00 00 00 00 | |
794 | EC 0x70: 00 00 00 00 00 12 30 40 *24 *26 *2c *27 *20 80 *1f 80 | |
795 | EC 0x80: 00 00 00 06 *37 *0e 03 00 00 00 0e 07 00 00 00 00 | |
796 | EC 0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 | |
797 | EC 0xa0: *ff 09 ff 09 ff ff *64 00 *00 *00 *a2 41 *ff *ff *e0 00 | |
798 | EC 0xb0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 | |
799 | EC 0xc0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 | |
800 | EC 0xd0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 | |
801 | EC 0xe0: 00 00 00 00 00 00 00 00 11 20 49 04 24 06 55 03 | |
802 | EC 0xf0: 31 55 48 54 35 38 57 57 08 2f 45 73 07 65 6c 1a | |
803 | ||
804 | This feature can be used to determine the register holding the fan | |
805 | speed on some models. To do that, do the following: | |
806 | ||
807 | - make sure the battery is fully charged | |
808 | - make sure the fan is running | |
809 | - run 'cat /proc/acpi/ibm/ecdump' several times, once per second or so | |
810 | ||
811 | The first step makes sure various charging-related values don't | |
812 | vary. The second ensures that the fan-related values do vary, since | |
813 | the fan speed fluctuates a bit. The third will (hopefully) mark the | |
814 | fan register with a star: | |
815 | ||
837ca6dd | 816 | [root@x40 ibm-acpi]# cat /proc/acpi/ibm/ecdump |
78f81cc4 BD |
817 | EC +00 +01 +02 +03 +04 +05 +06 +07 +08 +09 +0a +0b +0c +0d +0e +0f |
818 | EC 0x00: a7 47 87 01 fe 96 00 08 01 00 cb 00 00 00 40 00 | |
819 | EC 0x10: 00 00 ff ff f4 3c 87 09 01 ff 42 01 ff ff 0d 00 | |
820 | EC 0x20: 00 00 00 00 00 00 00 00 00 00 00 03 43 00 00 80 | |
821 | EC 0x30: 01 07 1a 00 30 04 00 00 85 00 00 10 00 50 00 00 | |
822 | EC 0x40: 00 00 00 00 00 00 14 01 00 04 00 00 00 00 00 00 | |
823 | EC 0x50: 00 c0 02 0d 00 01 01 02 02 03 03 03 03 bc 02 bc | |
824 | EC 0x60: 02 bc 02 00 00 00 00 00 00 00 00 00 00 00 00 00 | |
825 | EC 0x70: 00 00 00 00 00 12 30 40 24 27 2c 27 21 80 1f 80 | |
826 | EC 0x80: 00 00 00 06 *be 0d 03 00 00 00 0e 07 00 00 00 00 | |
827 | EC 0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 | |
828 | EC 0xa0: ff 09 ff 09 ff ff 64 00 00 00 a2 41 ff ff e0 00 | |
829 | EC 0xb0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 | |
830 | EC 0xc0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 | |
831 | EC 0xd0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 | |
832 | EC 0xe0: 00 00 00 00 00 00 00 00 11 20 49 04 24 06 55 03 | |
833 | EC 0xf0: 31 55 48 54 35 38 57 57 08 2f 45 73 07 65 6c 1a | |
834 | ||
835 | Another set of values that varies often is the temperature | |
836 | readings. Since temperatures don't change vary fast, you can take | |
837 | several quick dumps to eliminate them. | |
838 | ||
839 | You can use a similar method to figure out the meaning of other | |
840 | embedded controller registers - e.g. make sure nothing else changes | |
841 | except the charging or discharging battery to determine which | |
842 | registers contain the current battery capacity, etc. If you experiment | |
843 | with this, do send me your results (including some complete dumps with | |
844 | a description of the conditions when they were taken.) | |
845 | ||
7d5a015e HMH |
846 | LCD brightness control |
847 | ---------------------- | |
848 | ||
849 | procfs: /proc/acpi/ibm/brightness | |
850 | sysfs backlight device "thinkpad_screen" | |
78f81cc4 BD |
851 | |
852 | This feature allows software control of the LCD brightness on ThinkPad | |
7d5a015e HMH |
853 | models which don't have a hardware brightness slider. |
854 | ||
855 | It has some limitations: the LCD backlight cannot be actually turned on or off | |
856 | by this interface, and in many ThinkPad models, the "dim while on battery" | |
857 | functionality will be enabled by the BIOS when this interface is used, and | |
858 | cannot be controlled. | |
859 | ||
860 | The backlight control has eight levels, ranging from 0 to 7. Some of the | |
861 | levels may not be distinct. | |
862 | ||
863 | Procfs notes: | |
864 | ||
865 | The available commands are: | |
78f81cc4 BD |
866 | |
867 | echo up >/proc/acpi/ibm/brightness | |
868 | echo down >/proc/acpi/ibm/brightness | |
869 | echo 'level <level>' >/proc/acpi/ibm/brightness | |
870 | ||
7d5a015e HMH |
871 | Sysfs notes: |
872 | ||
873 | The interface is implemented through the backlight sysfs class, which is poorly | |
874 | documented at this time. | |
875 | ||
876 | Locate the thinkpad_screen device under /sys/class/backlight, and inside it | |
877 | there will be the following attributes: | |
878 | ||
879 | max_brightness: | |
880 | Reads the maximum brightness the hardware can be set to. | |
881 | The minimum is always zero. | |
882 | ||
883 | actual_brightness: | |
884 | Reads what brightness the screen is set to at this instant. | |
885 | ||
886 | brightness: | |
887 | Writes request the driver to change brightness to the given | |
888 | value. Reads will tell you what brightness the driver is trying | |
889 | to set the display to when "power" is set to zero and the display | |
890 | has not been dimmed by a kernel power management event. | |
891 | ||
892 | power: | |
893 | power management mode, where 0 is "display on", and 1 to 3 will | |
894 | dim the display backlight to brightness level 0 because | |
895 | thinkpad-acpi cannot really turn the backlight off. Kernel | |
896 | power management events can temporarily increase the current | |
897 | power management level, i.e. they can dim the display. | |
898 | ||
78f81cc4 | 899 | |
24f7ff0a SS |
900 | Volume control -- /proc/acpi/ibm/volume |
901 | --------------------------------------- | |
78f81cc4 BD |
902 | |
903 | This feature allows volume control on ThinkPad models which don't have | |
904 | a hardware volume knob. The available commands are: | |
905 | ||
906 | echo up >/proc/acpi/ibm/volume | |
907 | echo down >/proc/acpi/ibm/volume | |
908 | echo mute >/proc/acpi/ibm/volume | |
909 | echo 'level <level>' >/proc/acpi/ibm/volume | |
910 | ||
911 | The <level> number range is 0 to 15 although not all of them may be | |
912 | distinct. The unmute the volume after the mute command, use either the | |
913 | up or down command (the level command will not unmute the volume). | |
914 | The current volume level and mute state is shown in the file. | |
915 | ||
ecf2a80a HMH |
916 | Fan control and monitoring: fan speed, fan enable/disable |
917 | --------------------------------------------------------- | |
fe98a52c HMH |
918 | |
919 | procfs: /proc/acpi/ibm/fan | |
920 | sysfs device attributes: (hwmon) fan_input, pwm1, pwm1_enable | |
78f81cc4 | 921 | |
ecf2a80a HMH |
922 | NOTE NOTE NOTE: fan control operations are disabled by default for |
923 | safety reasons. To enable them, the module parameter "fan_control=1" | |
924 | must be given to thinkpad-acpi. | |
78f81cc4 | 925 | |
a12095c2 HMH |
926 | This feature attempts to show the current fan speed, control mode and |
927 | other fan data that might be available. The speed is read directly | |
928 | from the hardware registers of the embedded controller. This is known | |
ecf2a80a | 929 | to work on later R, T, X and Z series ThinkPads but may show a bogus |
a12095c2 HMH |
930 | value on other models. |
931 | ||
fe98a52c | 932 | Fan levels: |
a12095c2 | 933 | |
fe98a52c HMH |
934 | Most ThinkPad fans work in "levels" at the firmware interface. Level 0 |
935 | stops the fan. The higher the level, the higher the fan speed, although | |
936 | adjacent levels often map to the same fan speed. 7 is the highest | |
937 | level, where the fan reaches the maximum recommended speed. | |
78f81cc4 | 938 | |
fe98a52c HMH |
939 | Level "auto" means the EC changes the fan level according to some |
940 | internal algorithm, usually based on readings from the thermal sensors. | |
78f81cc4 | 941 | |
fe98a52c HMH |
942 | There is also a "full-speed" level, also known as "disengaged" level. |
943 | In this level, the EC disables the speed-locked closed-loop fan control, | |
944 | and drives the fan as fast as it can go, which might exceed hardware | |
945 | limits, so use this level with caution. | |
78f81cc4 | 946 | |
fe98a52c HMH |
947 | The fan usually ramps up or down slowly from one speed to another, and |
948 | it is normal for the EC to take several seconds to react to fan | |
949 | commands. The full-speed level may take up to two minutes to ramp up to | |
950 | maximum speed, and in some ThinkPads, the tachometer readings go stale | |
951 | while the EC is transitioning to the full-speed level. | |
a12095c2 | 952 | |
78f81cc4 | 953 | WARNING WARNING WARNING: do not leave the fan disabled unless you are |
a12095c2 HMH |
954 | monitoring all of the temperature sensor readings and you are ready to |
955 | enable it if necessary to avoid overheating. | |
956 | ||
957 | An enabled fan in level "auto" may stop spinning if the EC decides the | |
958 | ThinkPad is cool enough and doesn't need the extra airflow. This is | |
959 | normal, and the EC will spin the fan up if the varios thermal readings | |
960 | rise too much. | |
961 | ||
962 | On the X40, this seems to depend on the CPU and HDD temperatures. | |
963 | Specifically, the fan is turned on when either the CPU temperature | |
964 | climbs to 56 degrees or the HDD temperature climbs to 46 degrees. The | |
965 | fan is turned off when the CPU temperature drops to 49 degrees and the | |
966 | HDD temperature drops to 41 degrees. These thresholds cannot | |
967 | currently be controlled. | |
968 | ||
fe98a52c HMH |
969 | The ThinkPad's ACPI DSDT code will reprogram the fan on its own when |
970 | certain conditions are met. It will override any fan programming done | |
971 | through thinkpad-acpi. | |
972 | ||
973 | The thinkpad-acpi kernel driver can be programmed to revert the fan | |
974 | level to a safe setting if userspace does not issue one of the procfs | |
975 | fan commands: "enable", "disable", "level" or "watchdog", or if there | |
976 | are no writes to pwm1_enable (or to pwm1 *if and only if* pwm1_enable is | |
977 | set to 1, manual mode) within a configurable amount of time of up to | |
978 | 120 seconds. This functionality is called fan safety watchdog. | |
979 | ||
980 | Note that the watchdog timer stops after it enables the fan. It will be | |
981 | rearmed again automatically (using the same interval) when one of the | |
982 | above mentioned fan commands is received. The fan watchdog is, | |
983 | therefore, not suitable to protect against fan mode changes made through | |
984 | means other than the "enable", "disable", and "level" procfs fan | |
985 | commands, or the hwmon fan control sysfs interface. | |
986 | ||
987 | Procfs notes: | |
988 | ||
989 | The fan may be enabled or disabled with the following commands: | |
990 | ||
991 | echo enable >/proc/acpi/ibm/fan | |
992 | echo disable >/proc/acpi/ibm/fan | |
993 | ||
994 | Placing a fan on level 0 is the same as disabling it. Enabling a fan | |
995 | will try to place it in a safe level if it is too slow or disabled. | |
996 | ||
a12095c2 | 997 | The fan level can be controlled with the command: |
78f81cc4 | 998 | |
fe98a52c | 999 | echo 'level <level>' > /proc/acpi/ibm/fan |
a12095c2 | 1000 | |
fe98a52c HMH |
1001 | Where <level> is an integer from 0 to 7, or one of the words "auto" or |
1002 | "full-speed" (without the quotes). Not all ThinkPads support the "auto" | |
1003 | and "full-speed" levels. The driver accepts "disengaged" as an alias for | |
1004 | "full-speed", and reports it as "disengaged" for backwards | |
1005 | compatibility. | |
78f81cc4 BD |
1006 | |
1007 | On the X31 and X40 (and ONLY on those models), the fan speed can be | |
fe98a52c | 1008 | controlled to a certain degree. Once the fan is running, it can be |
78f81cc4 BD |
1009 | forced to run faster or slower with the following command: |
1010 | ||
fe98a52c | 1011 | echo 'speed <speed>' > /proc/acpi/ibm/fan |
78f81cc4 | 1012 | |
fe98a52c HMH |
1013 | The sustainable range of fan speeds on the X40 appears to be from about |
1014 | 3700 to about 7350. Values outside this range either do not have any | |
1015 | effect or the fan speed eventually settles somewhere in that range. The | |
1016 | fan cannot be stopped or started with this command. This functionality | |
1017 | is incomplete, and not available through the sysfs interface. | |
78f81cc4 | 1018 | |
fe98a52c HMH |
1019 | To program the safety watchdog, use the "watchdog" command. |
1020 | ||
1021 | echo 'watchdog <interval in seconds>' > /proc/acpi/ibm/fan | |
1022 | ||
1023 | If you want to disable the watchdog, use 0 as the interval. | |
1024 | ||
1025 | Sysfs notes: | |
1026 | ||
1027 | The sysfs interface follows the hwmon subsystem guidelines for the most | |
1028 | part, and the exception is the fan safety watchdog. | |
1029 | ||
b39fe582 HMH |
1030 | Writes to any of the sysfs attributes may return the EINVAL error if |
1031 | that operation is not supported in a given ThinkPad or if the parameter | |
1032 | is out-of-bounds, and EPERM if it is forbidden. They may also return | |
1033 | EINTR (interrupted system call), and EIO (I/O error while trying to talk | |
1034 | to the firmware). | |
1035 | ||
1036 | Features not yet implemented by the driver return ENOSYS. | |
1037 | ||
fe98a52c HMH |
1038 | hwmon device attribute pwm1_enable: |
1039 | 0: PWM offline (fan is set to full-speed mode) | |
1040 | 1: Manual PWM control (use pwm1 to set fan level) | |
1041 | 2: Hardware PWM control (EC "auto" mode) | |
1042 | 3: reserved (Software PWM control, not implemented yet) | |
1043 | ||
b39fe582 HMH |
1044 | Modes 0 and 2 are not supported by all ThinkPads, and the |
1045 | driver is not always able to detect this. If it does know a | |
1046 | mode is unsupported, it will return -EINVAL. | |
fe98a52c HMH |
1047 | |
1048 | hwmon device attribute pwm1: | |
1049 | Fan level, scaled from the firmware values of 0-7 to the hwmon | |
1050 | scale of 0-255. 0 means fan stopped, 255 means highest normal | |
1051 | speed (level 7). | |
1052 | ||
1053 | This attribute only commands the fan if pmw1_enable is set to 1 | |
1054 | (manual PWM control). | |
1055 | ||
1056 | hwmon device attribute fan1_input: | |
1057 | Fan tachometer reading, in RPM. May go stale on certain | |
1058 | ThinkPads while the EC transitions the PWM to offline mode, | |
1059 | which can take up to two minutes. May return rubbish on older | |
1060 | ThinkPads. | |
1061 | ||
1062 | driver attribute fan_watchdog: | |
1063 | Fan safety watchdog timer interval, in seconds. Minimum is | |
1064 | 1 second, maximum is 120 seconds. 0 disables the watchdog. | |
1065 | ||
1066 | To stop the fan: set pwm1 to zero, and pwm1_enable to 1. | |
1067 | ||
1068 | To start the fan in a safe mode: set pwm1_enable to 2. If that fails | |
b39fe582 HMH |
1069 | with EINVAL, try to set pwm1_enable to 1 and pwm1 to at least 128 (255 |
1070 | would be the safest choice, though). | |
1da177e4 | 1071 | |
38f996ed | 1072 | |
d3a6ade4 HMH |
1073 | EXPERIMENTAL: WAN |
1074 | ----------------- | |
1075 | ||
1076 | procfs: /proc/acpi/ibm/wan | |
cc4c24e1 | 1077 | sysfs device attribute: wwan_enable |
28b779d1 SS |
1078 | |
1079 | This feature is marked EXPERIMENTAL because the implementation | |
1080 | directly accesses hardware registers and may not work as expected. USE | |
1081 | WITH CAUTION! To use this feature, you need to supply the | |
1082 | experimental=1 parameter when loading the module. | |
1083 | ||
d3a6ade4 HMH |
1084 | This feature shows the presence and current state of a W-WAN (Sierra |
1085 | Wireless EV-DO) device. | |
1086 | ||
1087 | It was tested on a Lenovo Thinkpad X60. It should probably work on other | |
1088 | Thinkpad models which come with this module installed. | |
1089 | ||
1090 | Procfs notes: | |
1091 | ||
1092 | If the W-WAN card is installed, the following commands can be used: | |
28b779d1 SS |
1093 | |
1094 | echo enable > /proc/acpi/ibm/wan | |
1095 | echo disable > /proc/acpi/ibm/wan | |
1096 | ||
d3a6ade4 HMH |
1097 | Sysfs notes: |
1098 | ||
1099 | If the W-WAN card is installed, it can be enabled / | |
cc4c24e1 | 1100 | disabled through the "wwan_enable" thinkpad-acpi device |
d3a6ade4 HMH |
1101 | attribute, and its current status can also be queried. |
1102 | ||
1103 | enable: | |
1104 | 0: disables WWAN card / WWAN card is disabled | |
1105 | 1: enables WWAN card / WWAN card is enabled. | |
1106 | ||
1107 | Note: this interface will be probably be superseeded by the | |
cc4c24e1 | 1108 | generic rfkill class, so it is NOT to be considered stable yet. |
1da177e4 | 1109 | |
78f81cc4 BD |
1110 | Multiple Commands, Module Parameters |
1111 | ------------------------------------ | |
1da177e4 LT |
1112 | |
1113 | Multiple commands can be written to the proc files in one shot by | |
1114 | separating them with commas, for example: | |
1115 | ||
1116 | echo enable,0xffff > /proc/acpi/ibm/hotkey | |
1117 | echo lcd_disable,crt_enable > /proc/acpi/ibm/video | |
1118 | ||
643f12db HMH |
1119 | Commands can also be specified when loading the thinkpad-acpi module, |
1120 | for example: | |
1da177e4 | 1121 | |
643f12db | 1122 | modprobe thinkpad_acpi hotkey=enable,0xffff video=auto_disable |
1da177e4 | 1123 | |
132ce091 HMH |
1124 | Enabling debugging output |
1125 | ------------------------- | |
1126 | ||
1127 | The module takes a debug paramater which can be used to selectively | |
1128 | enable various classes of debugging output, for example: | |
1129 | ||
1130 | modprobe ibm_acpi debug=0xffff | |
1131 | ||
1132 | will enable all debugging output classes. It takes a bitmask, so | |
1133 | to enable more than one output class, just add their values. | |
1134 | ||
fe08bc4b HMH |
1135 | Debug bitmask Description |
1136 | 0x0001 Initialization and probing | |
1137 | 0x0002 Removal | |
1138 | ||
132ce091 HMH |
1139 | There is also a kernel build option to enable more debugging |
1140 | information, which may be necessary to debug driver problems. | |
0dcef77c | 1141 | |
176750d6 HMH |
1142 | The level of debugging information output by the driver can be changed |
1143 | at runtime through sysfs, using the driver attribute debug_level. The | |
1144 | attribute takes the same bitmask as the debug module parameter above. | |
1145 | ||
0dcef77c HMH |
1146 | Force loading of module |
1147 | ----------------------- | |
1148 | ||
1149 | If thinkpad-acpi refuses to detect your ThinkPad, you can try to specify | |
1150 | the module parameter force_load=1. Regardless of whether this works or | |
1151 | not, please contact ibm-acpi-devel@lists.sourceforge.net with a report. | |
176750d6 HMH |
1152 | |
1153 | ||
1154 | Sysfs interface changelog: | |
1155 | ||
1156 | 0x000100: Initial sysfs support, as a single platform driver and | |
1157 | device. | |
94b08713 HMH |
1158 | 0x000200: Hot key support for 32 hot keys, and radio slider switch |
1159 | support. |