Commit | Line | Data |
---|---|---|
61521e39 HUK |
1 | /* Device tree file for the Zyxel NSA 325 NAS box. |
2 | * | |
3 | * Copyright (c) 2015, Hans Ulli Kroll <ulli.kroll@googlemail.com> | |
4 | * | |
5 | * This program is free software; you can redistribute it and/or | |
6 | * modify it under the terms of the GNU General Public License | |
7 | * as published by the Free Software Foundation; either version | |
8 | * 2 of the License, or (at your option) any later version. | |
9 | * | |
10 | * Based upon the board setup file created by Peter Schildmann | |
11 | */ | |
12 | ||
13 | /dts-v1/; | |
14 | ||
15 | #include "kirkwood-nsa3x0-common.dtsi" | |
16 | ||
17 | / { | |
18 | model = "ZyXEL NSA325"; | |
19 | compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood"; | |
20 | ||
21 | memory { | |
22 | device_type = "memory"; | |
23 | reg = <0x00000000 0x20000000>; | |
24 | }; | |
25 | ||
26 | chosen { | |
27 | bootargs = "console=ttyS0,115200"; | |
28 | stdout-path = &uart0; | |
29 | }; | |
30 | ||
61521e39 HUK |
31 | ocp@f1000000 { |
32 | pinctrl: pin-controller@10000 { | |
33 | pinctrl-names = "default"; | |
34 | ||
35 | pmx_led_hdd2_green: pmx-led-hdd2-green { | |
36 | marvell,pins = "mpp12"; | |
37 | marvell,function = "gpio"; | |
38 | }; | |
39 | ||
40 | pmx_led_hdd2_red: pmx-led-hdd2-red { | |
41 | marvell,pins = "mpp13"; | |
42 | marvell,function = "gpio"; | |
43 | }; | |
44 | ||
45 | pmx_mcu_data: pmx-mcu-data { | |
46 | marvell,pins = "mpp14"; | |
47 | marvell,function = "gpio"; | |
48 | }; | |
49 | ||
50 | pmx_led_usb_green: pmx-led-usb-green { | |
51 | marvell,pins = "mpp15"; | |
52 | marvell,function = "gpio"; | |
53 | }; | |
54 | ||
55 | pmx_mcu_clk: pmx-mcu-clk { | |
56 | marvell,pins = "mpp16"; | |
57 | marvell,function = "gpio"; | |
58 | }; | |
59 | ||
60 | pmx_mcu_act: pmx-mcu-act { | |
61 | marvell,pins = "mpp17"; | |
62 | marvell,function = "gpio"; | |
63 | }; | |
64 | ||
65 | pmx_led_sys_green: pmx-led-sys-green { | |
66 | marvell,pins = "mpp28"; | |
67 | marvell,function = "gpio"; | |
68 | }; | |
69 | ||
70 | pmx_led_sys_orange: pmx-led-sys-orange { | |
71 | marvell,pins = "mpp29"; | |
72 | marvell,function = "gpio"; | |
73 | }; | |
74 | ||
75 | pmx_led_hdd1_green: pmx-led-hdd1-green { | |
76 | marvell,pins = "mpp41"; | |
77 | marvell,function = "gpio"; | |
78 | }; | |
79 | ||
80 | pmx_led_hdd1_red: pmx-led-hdd1-red { | |
81 | marvell,pins = "mpp42"; | |
82 | marvell,function = "gpio"; | |
83 | }; | |
84 | ||
85 | pmx_htp: pmx-htp { | |
86 | marvell,pins = "mpp43"; | |
87 | marvell,function = "gpio"; | |
88 | }; | |
89 | ||
90 | /* | |
91 | * Buzzer needs to be switched at around 1kHz so is | |
92 | * not compatible with the gpio-beeper driver. | |
93 | */ | |
94 | pmx_buzzer: pmx-buzzer { | |
95 | marvell,pins = "mpp44"; | |
96 | marvell,function = "gpio"; | |
97 | }; | |
98 | ||
99 | pmx_vid_b1: pmx-vid-b1 { | |
100 | marvell,pins = "mpp45"; | |
101 | marvell,function = "gpio"; | |
102 | }; | |
103 | ||
104 | pmx_power_resume_data: pmx-power-resume-data { | |
105 | marvell,pins = "mpp47"; | |
106 | marvell,function = "gpio"; | |
107 | }; | |
108 | ||
109 | pmx_power_resume_clk: pmx-power-resume-clk { | |
110 | marvell,pins = "mpp49"; | |
111 | marvell,function = "gpio"; | |
112 | }; | |
113 | ||
114 | pmx_pwr_sata1: pmx-pwr-sata1 { | |
115 | marvell,pins = "mpp47"; | |
116 | marvell,function = "gpio"; | |
117 | }; | |
118 | }; | |
119 | ||
120 | /* This board uses the pcf8563 RTC instead of the SoC RTC */ | |
121 | rtc@10300 { | |
122 | status = "disabled"; | |
123 | }; | |
124 | ||
125 | i2c@11000 { | |
126 | status = "okay"; | |
127 | ||
128 | pcf8563: pcf8563@51 { | |
129 | compatible = "nxp,pcf8563"; | |
130 | reg = <0x51>; | |
131 | }; | |
132 | }; | |
133 | }; | |
134 | ||
135 | regulators { | |
136 | compatible = "simple-bus"; | |
137 | #address-cells = <1>; | |
138 | #size-cells = <0>; | |
139 | pinctrl-0 = <&pmx_pwr_sata1>; | |
140 | pinctrl-names = "default"; | |
141 | ||
142 | usb0_power: regulator@1 { | |
143 | enable-active-high; | |
144 | }; | |
145 | ||
146 | sata1_power: regulator@2 { | |
147 | compatible = "regulator-fixed"; | |
148 | reg = <2>; | |
149 | regulator-name = "SATA1 Power"; | |
150 | regulator-min-microvolt = <5000000>; | |
151 | regulator-max-microvolt = <5000000>; | |
152 | regulator-always-on; | |
153 | regulator-boot-on; | |
154 | enable-active-high; | |
155 | gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>; | |
156 | }; | |
157 | }; | |
158 | ||
159 | gpio-leds { | |
160 | compatible = "gpio-leds"; | |
161 | pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red | |
162 | &pmx_led_usb_green | |
163 | &pmx_led_sys_green &pmx_led_sys_orange | |
164 | &pmx_led_copy_green &pmx_led_copy_red | |
165 | &pmx_led_hdd1_green &pmx_led_hdd1_red>; | |
166 | pinctrl-names = "default"; | |
167 | ||
168 | green-sys { | |
169 | label = "nsa325:green:sys"; | |
170 | gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; | |
171 | }; | |
172 | orange-sys { | |
173 | label = "nsa325:orange:sys"; | |
174 | gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; | |
175 | }; | |
176 | green-hdd1 { | |
177 | label = "nsa325:green:hdd1"; | |
178 | gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; | |
179 | }; | |
180 | red-hdd1 { | |
181 | label = "nsa325:red:hdd1"; | |
182 | gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; | |
183 | }; | |
184 | green-hdd2 { | |
185 | label = "nsa325:green:hdd2"; | |
186 | gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; | |
187 | }; | |
188 | red-hdd2 { | |
189 | label = "nsa325:red:hdd2"; | |
190 | gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; | |
191 | }; | |
192 | green-usb { | |
193 | label = "nsa325:green:usb"; | |
194 | gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; | |
195 | }; | |
196 | green-copy { | |
197 | label = "nsa325:green:copy"; | |
198 | gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; | |
199 | }; | |
200 | red-copy { | |
201 | label = "nsa325:red:copy"; | |
202 | gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; | |
203 | }; | |
204 | ||
205 | /* The following pins are currently not assigned to a driver, | |
206 | some of them should be configured as inputs. | |
207 | pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act | |
208 | &pmx_htp &pmx_vid_b1 | |
209 | &pmx_power_resume_data &pmx_power_resume_clk>; */ | |
210 | }; | |
211 | ||
212 | ||
213 | }; | |
214 | ||
215 | &mdio { | |
216 | status = "okay"; | |
217 | ethphy0: ethernet-phy@1 { | |
218 | reg = <1>; | |
219 | }; | |
220 | }; | |
221 | ||
222 | ð0 { | |
223 | status = "okay"; | |
224 | ethernet0-port@0 { | |
225 | phy-handle = <ðphy0>; | |
226 | }; | |
227 | }; | |
228 | ||
eb13cf83 AL |
229 | &pciec { |
230 | status = "okay"; | |
231 | }; | |
232 | ||
233 | &pcie0 { | |
234 | status = "okay"; | |
235 | }; |