[deliverable/linux.git] / arch / arm / boot / dts / logicpd-torpedo-som.dtsi

/*
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <dt-bindings/input/input.h>

/ {
	cpus {
		cpu@0 {
			cpu0-supply = <&vcc>;
		};
	};

	leds {
		compatible = "gpio-leds";
		user0 {
			label = "user0";
			gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>;	/* LEDA */
			linux,default-trigger = "none";
		};
	};

	wl12xx_vmmc: wl12xx_vmmc {
		compatible = "regulator-fixed";
		regulator-name = "vwl1271";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		gpio = <&gpio5 29 0>;   /* gpio157 */
		startup-delay-us = <70000>;
		enable-active-high;
		vin-supply = <&vmmc2>;
	};
};

&gpmc {
	ranges = <0 0 0x00000000 0x1000000>;	/* CS0: 16MB for NAND */

	nand@0,0 {
		linux,mtd-name = "micron,mt29f4g16abbda3w";
		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
		nand-bus-width = <16>;
		ti,nand-ecc-opt = "bch8";
		gpmc,sync-clk-ps = <0>;
		gpmc,cs-on-ns = <0>;
		gpmc,cs-rd-off-ns = <44>;
		gpmc,cs-wr-off-ns = <44>;
		gpmc,adv-on-ns = <6>;
		gpmc,adv-rd-off-ns = <34>;
		gpmc,adv-wr-off-ns = <44>;
		gpmc,we-off-ns = <40>;
		gpmc,oe-off-ns = <54>;
		gpmc,access-ns = <64>;
		gpmc,rd-cycle-ns = <82>;
		gpmc,wr-cycle-ns = <82>;
		gpmc,wr-access-ns = <40>;
		gpmc,wr-data-mux-bus-ns = <0>;
		gpmc,device-width = <2>;
		#address-cells = <1>;
		#size-cells = <1>;

		/* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */

		x-loader@0 {
			label = "x-loader";
			reg = <0 0x80000>;
		};

		bootloaders@80000 {
			label = "u-boot";
			reg = <0x80000 0x1e0000>;
		};

		bootloaders_env@260000 {
			label = "u-boot-env";
			reg = <0x260000 0x20000>;
		};

		kernel@280000 {
			label = "kernel";
			reg = <0x280000 0x400000>;
		};

		filesystem@680000 {
			label = "fs";
			reg = <0x680000 0>;	/* 0 = MTDPART_SIZ_FULL */
		};
	};
};

&i2c1 {
	clock-frequency = <2600000>;

	twl: twl@48 {
		reg = <0x48>;
		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
		interrupt-parent = <&intc>;
		twl_audio: audio {
			compatible = "ti,twl4030-audio";
			codec {
			};
		};
	};
};

&i2c2 {
	clock-frequency = <400000>;
};

&i2c3 {
	clock-frequency = <400000>;
};

&i2c2 {
	clock-frequency = <400000>;
};

&i2c3 {
	clock-frequency = <400000>;
	at24@50 {
		compatible = "at24,24c02";
		readonly;
		reg = <0x50>;
	};
};

/*
 * Only found on the wireless SOM. For the SOM without wireless, the pins for
 * MMC3 can be routed with jumpers to the second MMC slot on the devkit and
 * gpio157 is not connected. So this should be OK to keep common for now,
 * probably device tree overlays is the way to go with the various SOM and
 * jumpering combinations for the long run.
 */
&mmc3 {
	interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
	pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
	pinctrl-names = "default";
	vmmc-supply = <&wl12xx_vmmc>;
	non-removable;
	bus-width = <4>;
	cap-power-off-card;
	#address-cells = <1>;
	#size-cells = <0>;
	wlcore: wlcore@2 {
		compatible = "ti,wl1283";
		reg = <2>;
		interrupt-parent = <&gpio5>;
		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
		ref-clock-frequency = <26000000>;
	};
};

&omap3_pmx_core {
	mmc3_pins: pinmux_mm3_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat4.sdmmc3_dat0 */
			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat5.sdmmc3_dat1 */
			OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat2 */
			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat3 */
			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
			OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4)	/* mcbsp1_fsr.gpio_157 */
		>;
	};
	mcbsp2_pins: pinmux_mcbsp2_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)        /* mcbsp2_fsx */
			OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)        /* mcbsp2_clkx */
			OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0)        /* mcbsp2_dr */
			OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0)       /* mcbsp2_dx */
		>;
	};
	uart2_pins: pinmux_uart2_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0)	/* uart2_cts.uart2_cts */
			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)	/* uart2_rts .uart2_rts*/
			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)	/* uart2_tx.uart2_tx */
			OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)	/* uart2_rx.uart2_rx */
			OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)	/* GPIO_162,BT_EN */
		>;
	};
	mcspi1_pins: pinmux_mcspi1_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)        /* mcspi1_clk.mcspi1_clk */
			OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_simo.mcspi1_simo */
			OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
			OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_cs0.mcspi1_cs0 */
		>;
	};

};

&uart2 {
	interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
	pinctrl-names = "default";
	pinctrl-0 = <&uart2_pins>;
};

&mcspi1 {
	pinctrl-names = "default";
	pinctrl-0 = <&mcspi1_pins>;
};

&omap3_pmx_core2 {
	mmc3_core2_pins: pinmux_mmc3_core2_pins {
		pinctrl-single,pins = <
			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_clk.sdmmc3_clk */
			OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_ctl.sdmmc3_cmd */
		>;
	};
};

#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"

&twl {
	twl_power: power {
		compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
		ti,use_poweroff;
	};
};

&twl_gpio {
	ti,use-leds;
};
Commit	Line	Data
687c2767 TL	1	/*
	2	* This program is free software; you can redistribute it and/or modify
	3	* it under the terms of the GNU General Public License version 2 as
	4	* published by the Free Software Foundation.
	5	*/
	6
	7	#include <dt-bindings/input/input.h>
	8
	9	/ {
	10	cpus {
	11	cpu@0 {
	12	cpu0-supply = <&vcc>;
	13	};
	14	};
	15
	16	leds {
	17	compatible = "gpio-leds";
	18	user0 {
	19	label = "user0";
	20	gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* LEDA */
	21	linux,default-trigger = "none";
	22	};
	23	};
	24
	25	wl12xx_vmmc: wl12xx_vmmc {
	26	compatible = "regulator-fixed";
	27	regulator-name = "vwl1271";
	28	regulator-min-microvolt = <1800000>;
	29	regulator-max-microvolt = <1800000>;
	30	gpio = <&gpio5 29 0>; /* gpio157 */
	31	startup-delay-us = <70000>;
	32	enable-active-high;
	33	vin-supply = <&vmmc2>;
	34	};
	35	};
	36
	37	&gpmc {
	38	ranges = <0 0 0x00000000 0x1000000>; /* CS0: 16MB for NAND */
	39
	40	nand@0,0 {
	41	linux,mtd-name = "micron,mt29f4g16abbda3w";
	42	reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
	43	nand-bus-width = <16>;
	44	ti,nand-ecc-opt = "bch8";
	45	gpmc,sync-clk-ps = <0>;
	46	gpmc,cs-on-ns = <0>;
	47	gpmc,cs-rd-off-ns = <44>;
	48	gpmc,cs-wr-off-ns = <44>;
	49	gpmc,adv-on-ns = <6>;
	50	gpmc,adv-rd-off-ns = <34>;
	51	gpmc,adv-wr-off-ns = <44>;
	52	gpmc,we-off-ns = <40>;
	53	gpmc,oe-off-ns = <54>;
	54	gpmc,access-ns = <64>;
	55	gpmc,rd-cycle-ns = <82>;
	56	gpmc,wr-cycle-ns = <82>;
	57	gpmc,wr-access-ns = <40>;
	58	gpmc,wr-data-mux-bus-ns = <0>;
	59	gpmc,device-width = <2>;
	60	#address-cells = <1>;
	61	#size-cells = <1>;
	62
	63	/* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */
	64
65	x-loader@0 {
66	label = "x-loader";
67	reg = <0 0x80000>;
68	};
69
70	bootloaders@80000 {
71	label = "u-boot";
72	reg = <0x80000 0x1e0000>;
73	};
74
75	bootloaders_env@260000 {
76	label = "u-boot-env";
77	reg = <0x260000 0x20000>;
78	};
79
80	kernel@280000 {
81	label = "kernel";
82	reg = <0x280000 0x400000>;
83	};
84
85	filesystem@680000 {
86	label = "fs";
87	reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */
88	};
89	};
90	};
91
92	&i2c1 {
93	clock-frequency = <2600000>;
94
95	twl: twl@48 {
96	reg = <0x48>;
97	interrupts = <7>; /* SYS_NIRQ cascaded to intc */
98	interrupt-parent = <&intc>;
f81902e4 AF	99	twl_audio: audio {
	100	compatible = "ti,twl4030-audio";
	101	codec {
	102	};
	103	};
687c2767 TL	104	};
	105	};
	106
6b3d42c6 AF	107	&i2c2 {
	108	clock-frequency = <400000>;
	109	};
	110
	111	&i2c3 {
	112	clock-frequency = <400000>;
	113	};
	114
7cd6ca77 AF	115	&i2c2 {
	116	clock-frequency = <400000>;
	117	};
	118
	119	&i2c3 {
	120	clock-frequency = <400000>;
5e3447a2 AF	121	at24@50 {
	122	compatible = "at24,24c02";
	123	readonly;
	124	reg = <0x50>;
	125	};
7cd6ca77 AF	126	};
7cd6ca77 AF	127
687c2767 TL	128	/*
	129	* Only found on the wireless SOM. For the SOM without wireless, the pins for
	130	* MMC3 can be routed with jumpers to the second MMC slot on the devkit and
	131	* gpio157 is not connected. So this should be OK to keep common for now,
	132	* probably device tree overlays is the way to go with the various SOM and
	133	* jumpering combinations for the long run.
	134	*/
	135	&mmc3 {
	136	interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
	137	pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
	138	pinctrl-names = "default";
	139	vmmc-supply = <&wl12xx_vmmc>;
	140	non-removable;
	141	bus-width = <4>;
	142	cap-power-off-card;
	143	#address-cells = <1>;
	144	#size-cells = <0>;
	145	wlcore: wlcore@2 {
	146	compatible = "ti,wl1283";
	147	reg = <2>;
	148	interrupt-parent = <&gpio5>;
	149	interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
	150	ref-clock-frequency = <26000000>;
	151	};
	152	};
	153
	154	&omap3_pmx_core {
	155	mmc3_pins: pinmux_mm3_pins {
	156	pinctrl-single,pins = <
	157	OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP \| MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
	158	OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP \| MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
	159	OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP \| MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
	160	OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP \| MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
	161	OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP \| MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
	162	OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT \| MUX_MODE4) /* mcbsp1_fsr.gpio_157 */
	163	>;
	164	};
f81902e4 AF	165	mcbsp2_pins: pinmux_mcbsp2_pins {
	166	pinctrl-single,pins = <
	167	OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT \| MUX_MODE0) /* mcbsp2_fsx */
	168	OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT \| MUX_MODE0) /* mcbsp2_clkx */
	169	OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT \| MUX_MODE0) /* mcbsp2_dr */
	170	OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT \| MUX_MODE0) /* mcbsp2_dx */
	171	>;
	172	};
9ff502f5 AF	173	uart2_pins: pinmux_uart2_pins {
	174	pinctrl-single,pins = <
	175	OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT \| MUX_MODE0) /* uart2_cts.uart2_cts */
	176	OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT \| MUX_MODE0) /* uart2_rts .uart2_rts*/
	177	OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT \| MUX_MODE0) /* uart2_tx.uart2_tx */
	178	OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT \| MUX_MODE0) /* uart2_rx.uart2_rx */
	179	OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT \| MUX_MODE4) /* GPIO_162,BT_EN */
	180	>;
	181	};
40d5cb20 AF	182	mcspi1_pins: pinmux_mcspi1_pins {
	183	pinctrl-single,pins = <
	184	OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT \| MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
	185	OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT \| MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
	186	OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP \| MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
	187	OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT \| MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
	188	>;
	189	};
	190
9ff502f5 AF	191	};
	192
	193	&uart2 {
	194	interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
	195	pinctrl-names = "default";
	196	pinctrl-0 = <&uart2_pins>;
687c2767 TL	197	};
687c2767 TL	198
40d5cb20 AF	199	&mcspi1 {
	200	pinctrl-names = "default";
	201	pinctrl-0 = <&mcspi1_pins>;
	202	};
	203
687c2767 TL	204	&omap3_pmx_core2 {
	205	mmc3_core2_pins: pinmux_mmc3_core2_pins {
	206	pinctrl-single,pins = <
	207	OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP \| MUX_MODE2) /* etk_clk.sdmmc3_clk */
	208	OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP \| MUX_MODE2) /* etk_ctl.sdmmc3_cmd */
	209	>;
	210	};
	211	};
	212
	213	#include "twl4030.dtsi"
	214	#include "twl4030_omap3.dtsi"
	215
	216	&twl {
	217	twl_power: power {
	218	compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
	219	ti,use_poweroff;
	220	};
	221	};
	222
	223	&twl_gpio {
	224	ti,use-leds;
	225	};