[deliverable/linux.git] / arch / arm / boot / dts / lpc18xx.dtsi

/*
 * Common base for NXP LPC18xx and LPC43xx devices.
 *
 * Copyright 2015 Joachim Eastwood <manabian@gmail.com>
 *
 * This code is released using a dual license strategy: BSD/GPL
 * You can choose the licence that better fits your requirements.
 *
 * Released under the terms of 3-clause BSD License
 * Released under the terms of GNU General Public License Version 2.0
 *
 */

#include "armv7-m.dtsi"

#include "dt-bindings/clock/lpc18xx-cgu.h"
#include "dt-bindings/clock/lpc18xx-ccu.h"

#define LPC_PIN(port, pin)	(0x##port * 32 + pin)
#define LPC_GPIO(port, pin)	(port * 32 + pin)

/ {
	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		cpu@0 {
			compatible = "arm,cortex-m3";
			device_type = "cpu";
			reg = <0x0>;
			clocks = <&ccu1 CLK_CPU_CORE>;
		};
	};

	clocks {
		xtal: xtal {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <12000000>;
		};

		xtal32: xtal32 {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <32768>;
		};

		enet_rx_clk: enet_rx_clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <0>;
			clock-output-names = "enet_rx_clk";
		};

		enet_tx_clk: enet_tx_clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <0>;
			clock-output-names = "enet_tx_clk";
		};

		gp_clkin: gp_clkin {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <0>;
			clock-output-names = "gp_clkin";
		};
	};

	soc {
		sct_pwm: pwm@40000000 {
			compatible = "nxp,lpc1850-sct-pwm";
			reg = <0x40000000 0x1000>;
			clocks =<&ccu1 CLK_CPU_SCT>;
			clock-names = "pwm";
			resets = <&rgu 37>;
			#pwm-cells = <3>;
			status = "disabled";
		};

		dmac: dma-controller@40002000 {
			compatible = "arm,pl080", "arm,primecell";
			arm,primecell-periphid = <0x00041080>;
			reg = <0x40002000 0x1000>;
			interrupts = <2>;
			clocks = <&ccu1 CLK_CPU_DMA>;
			clock-names = "apb_pclk";
			resets = <&rgu 19>;
			#dma-cells = <2>;
			dma-channels = <8>;
			dma-requests = <16>;
			lli-bus-interface-ahb1;
			lli-bus-interface-ahb2;
			mem-bus-interface-ahb1;
			mem-bus-interface-ahb2;
			memcpy-burst-size = <256>;
			memcpy-bus-width = <32>;
		};

		spifi: flash-controller@40003000 {
			compatible = "nxp,lpc1773-spifi";
			reg = <0x40003000 0x1000>, <0x14000000 0x4000000>;
			reg-names = "spifi", "flash";
			interrupts = <30>;
			clocks = <&ccu1 CLK_SPIFI>, <&ccu1 CLK_CPU_SPIFI>;
			clock-names = "spifi", "reg";
			resets = <&rgu 53>;
			status = "disabled";
		};

		mmcsd: mmcsd@40004000 {
			compatible = "snps,dw-mshc";
			reg = <0x40004000 0x1000>;
			interrupts = <6>;
			num-slots = <1>;
			clocks = <&ccu2 CLK_SDIO>, <&ccu1 CLK_CPU_SDIO>;
			clock-names = "ciu", "biu";
			resets = <&rgu 20>;
			status = "disabled";
		};

		usb0: ehci@40006100 {
			compatible = "nxp,lpc1850-ehci", "generic-ehci";
			reg = <0x40006100 0x100>;
			interrupts = <8>;
			clocks = <&ccu1 CLK_CPU_USB0>;
			resets = <&rgu 17>;
			phys = <&usb0_otg_phy>;
			phy-names = "usb";
			has-transaction-translator;
			status = "disabled";
		};

		usb1: ehci@40007100 {
			compatible = "nxp,lpc1850-ehci", "generic-ehci";
			reg = <0x40007100 0x100>;
			interrupts = <9>;
			clocks = <&ccu1 CLK_CPU_USB1>;
			resets = <&rgu 18>;
			status = "disabled";
		};

		emc: memory-controller@40005000 {
			compatible = "arm,pl172", "arm,primecell";
			reg = <0x40005000 0x1000>;
			clocks = <&ccu1 CLK_CPU_EMCDIV>, <&ccu1 CLK_CPU_EMC>;
			clock-names = "mpmcclk", "apb_pclk";
			resets = <&rgu 21>;
			#address-cells = <2>;
			#size-cells = <1>;
			ranges = <0 0 0x1c000000 0x1000000
				  1 0 0x1d000000 0x1000000
				  2 0 0x1e000000 0x1000000
				  3 0 0x1f000000 0x1000000>;
			status = "disabled";
		};

		lcdc: lcd-controller@40008000 {
			compatible = "arm,pl111", "arm,primecell";
			reg = <0x40008000 0x1000>;
			interrupts = <7>;
			interrupt-names = "combined";
			clocks = <&cgu BASE_LCD_CLK>, <&ccu1 CLK_CPU_LCD>;
			clock-names = "clcdclk", "apb_pclk";
			resets = <&rgu 16>;
			status = "disabled";
		};

		eeprom: eeprom@4000e000 {
			compatible = "nxp,lpc1857-eeprom";
			reg = <0x4000e000 0x1000>, <0x20040000 0x4000>;
			reg-names = "reg", "mem";
			clocks = <&ccu1 CLK_CPU_EEPROM>;
			clock-names = "eeprom";
			resets = <&rgu 27>;
			interrupts = <4>;
			status = "disabled";
		};

		mac: ethernet@40010000 {
			compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac";
			reg = <0x40010000 0x2000>;
			interrupts = <5>;
			interrupt-names	= "macirq";
			clocks = <&ccu1 CLK_CPU_ETHERNET>;
			clock-names = "stmmaceth";
			resets = <&rgu 22>;
			reset-names = "stmmaceth";
			status = "disabled";
		};

		creg: syscon@40043000 {
			compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd";
			reg = <0x40043000 0x1000>;
			clocks = <&ccu1 CLK_CPU_CREG>;
			resets = <&rgu 5>;

			creg_clk: clock-controller {
				compatible = "nxp,lpc1850-creg-clk";
				clocks = <&xtal32>;
				#clock-cells = <1>;
			};

			usb0_otg_phy: phy {
				compatible = "nxp,lpc1850-usb-otg-phy";
				clocks = <&ccu1 CLK_USB0>;
				#phy-cells = <0>;
			};

			dmamux: dma-mux {
				compatible = "nxp,lpc1850-dmamux";
				#dma-cells = <3>;
				dma-requests = <64>;
				dma-masters = <&dmac>;
			};
		};

		rtc: rtc@40046000 {
			compatible = "nxp,lpc1850-rtc", "nxp,lpc1788-rtc";
			reg = <0x40046000 0x1000>;
			interrupts = <47>;
			clocks = <&creg_clk 0>, <&ccu1 CLK_CPU_BUS>;
			clock-names = "rtc", "reg";
		};

		cgu: clock-controller@40050000 {
			compatible = "nxp,lpc1850-cgu";
			reg = <0x40050000 0x1000>;
			#clock-cells = <1>;
			clocks = <&xtal>, <&creg_clk 1>, <&enet_rx_clk>, <&enet_tx_clk>, <&gp_clkin>;
		};

		ccu1: clock-controller@40051000 {
			compatible = "nxp,lpc1850-ccu";
			reg = <0x40051000 0x1000>;
			#clock-cells = <1>;
			clocks = <&cgu BASE_APB3_CLK>,   <&cgu BASE_APB1_CLK>,
				 <&cgu BASE_SPIFI_CLK>,  <&cgu BASE_CPU_CLK>,
				 <&cgu BASE_PERIPH_CLK>, <&cgu BASE_USB0_CLK>,
				 <&cgu BASE_USB1_CLK>,   <&cgu BASE_SPI_CLK>;
			clock-names = "base_apb3_clk",   "base_apb1_clk",
				      "base_spifi_clk",  "base_cpu_clk",
				      "base_periph_clk", "base_usb0_clk",
				      "base_usb1_clk",   "base_spi_clk";
		};

		ccu2: clock-controller@40052000 {
			compatible = "nxp,lpc1850-ccu";
			reg = <0x40052000 0x1000>;
			#clock-cells = <1>;
			clocks = <&cgu BASE_AUDIO_CLK>, <&cgu BASE_UART3_CLK>,
				 <&cgu BASE_UART2_CLK>, <&cgu BASE_UART1_CLK>,
				 <&cgu BASE_UART0_CLK>, <&cgu BASE_SSP1_CLK>,
				 <&cgu BASE_SSP0_CLK>,  <&cgu BASE_SDIO_CLK>;
			clock-names = "base_audio_clk", "base_uart3_clk",
				      "base_uart2_clk", "base_uart1_clk",
				      "base_uart0_clk", "base_ssp1_clk",
				      "base_ssp0_clk",  "base_sdio_clk";
		};

		rgu: reset-controller@40053000 {
			compatible = "nxp,lpc1850-rgu";
			reg = <0x40053000 0x1000>;
			clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_BUS>;
			clock-names = "delay", "reg";
			#reset-cells = <1>;
		};

		watchdog@40080000 {
			compatible = "nxp,lpc1850-wwdt";
			reg = <0x40080000 0x24>;
			interrupts = <49>;
			clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_WWDT>;
			clock-names = "wdtclk", "reg";
		};

		uart0: serial@40081000 {
			compatible = "nxp,lpc1850-uart", "ns16550a";
			reg = <0x40081000 0x1000>;
			reg-shift = <2>;
			interrupts = <24>;
			clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>;
			clock-names = "uartclk", "reg";
			resets = <&rgu 44>;
			dmas = <&dmamux  1 1 2
				&dmamux  2 1 2
				&dmamux 11 2 2
				&dmamux 12 2 2>;
			dma-names = "tx", "rx", "tx", "rx";
			status = "disabled";
		};

		uart1: serial@40082000 {
			compatible = "nxp,lpc1850-uart", "ns16550a";
			reg = <0x40082000 0x1000>;
			reg-shift = <2>;
			interrupts = <25>;
			clocks = <&ccu2 CLK_APB0_UART1>, <&ccu1 CLK_CPU_UART1>;
			clock-names = "uartclk", "reg";
			resets = <&rgu 45>;
			dmas = <&dmamux 3 1 2
				&dmamux 4 1 2>;
			dma-names = "tx", "rx";
			status = "disabled";
		};

		ssp0: spi@40083000 {
			compatible = "arm,pl022", "arm,primecell";
			reg = <0x40083000 0x1000>;
			interrupts = <22>;
			clocks = <&ccu2 CLK_APB0_SSP0>, <&ccu1 CLK_CPU_SSP0>;
			clock-names = "sspclk", "apb_pclk";
			resets = <&rgu 50>;
			dmas = <&dmamux  9 0 2
				&dmamux 10 0 2>;
			dma-names = "rx", "tx";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		timer0: timer@40084000 {
			compatible = "nxp,lpc3220-timer";
			reg = <0x40084000 0x1000>;
			interrupts = <12>;
			clocks = <&ccu1 CLK_CPU_TIMER0>;
			clock-names = "timerclk";
			resets = <&rgu 32>;
		};

		timer1: timer@40085000 {
			compatible = "nxp,lpc3220-timer";
			reg = <0x40085000 0x1000>;
			interrupts = <13>;
			clocks = <&ccu1 CLK_CPU_TIMER1>;
			clock-names = "timerclk";
			resets = <&rgu 33>;
		};

		pinctrl: pinctrl@40086000 {
			compatible = "nxp,lpc1850-scu";
			reg = <0x40086000 0x1000>;
			clocks = <&ccu1 CLK_CPU_SCU>;
		};

		i2c0: i2c@400a1000 {
			compatible = "nxp,lpc1788-i2c";
			reg = <0x400a1000 0x1000>;
			interrupts = <18>;
			clocks = <&ccu1 CLK_APB1_I2C0>;
			resets = <&rgu 48>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		can1: can@400a4000 {
			compatible = "bosch,c_can";
			reg = <0x400a4000 0x1000>;
			interrupts = <43>;
			clocks = <&ccu1 CLK_APB1_CAN1>;
			resets = <&rgu 54>;
			status = "disabled";
		};

		uart2: serial@400c1000 {
			compatible = "nxp,lpc1850-uart", "ns16550a";
			reg = <0x400c1000 0x1000>;
			reg-shift = <2>;
			interrupts = <26>;
			clocks = <&ccu2 CLK_APB2_UART2>, <&ccu1 CLK_CPU_UART2>;
			clock-names = "uartclk", "reg";
			resets = <&rgu 46>;
			dmas = <&dmamux 5 1 2
				&dmamux 6 1 2>;
			dma-names = "tx", "rx";
			status = "disabled";
		};

		uart3: serial@400c2000 {
			compatible = "nxp,lpc1850-uart", "ns16550a";
			reg = <0x400c2000 0x1000>;
			reg-shift = <2>;
			interrupts = <27>;
			clocks = <&ccu2 CLK_APB2_UART3>, <&ccu1 CLK_CPU_UART3>;
			clock-names = "uartclk", "reg";
			resets = <&rgu 47>;
			dmas = <&dmamux  7 1 2
				&dmamux  8 1 2
				&dmamux 13 3 2
				&dmamux 14 3 2>;
			dma-names = "tx", "rx", "rx", "tx";
			status = "disabled";
		};

		timer2: timer@400c3000 {
			compatible = "nxp,lpc3220-timer";
			reg = <0x400c3000 0x1000>;
			interrupts = <14>;
			clocks = <&ccu1 CLK_CPU_TIMER2>;
			clock-names = "timerclk";
			resets = <&rgu 34>;
		};

		timer3: timer@400c4000 {
			compatible = "nxp,lpc3220-timer";
			reg = <0x400c4000 0x1000>;
			interrupts = <15>;
			clocks = <&ccu1 CLK_CPU_TIMER3>;
			clock-names = "timerclk";
			resets = <&rgu 35>;
		};

		ssp1: spi@400c5000 {
			compatible = "arm,pl022", "arm,primecell";
			reg = <0x400c5000 0x1000>;
			interrupts = <23>;
			clocks = <&ccu2 CLK_APB2_SSP1>, <&ccu1 CLK_CPU_SSP1>;
			clock-names = "sspclk", "apb_pclk";
			resets = <&rgu 51>;
			dmas = <&dmamux 11 2 2
				&dmamux 12 2 2
				&dmamux  3 3 2
				&dmamux  4 3 2
				&dmamux  5 2 2
				&dmamux  6 2 2
				&dmamux 13 2 2
				&dmamux 14 2 2>;
			dma-names = "rx", "tx", "tx", "rx",
				    "tx", "rx", "rx", "tx";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		i2c1: i2c@400e0000 {
			compatible = "nxp,lpc1788-i2c";
			reg = <0x400e0000 0x1000>;
			interrupts = <19>;
			clocks = <&ccu1 CLK_APB3_I2C1>;
			resets = <&rgu 49>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		dac: dac@400e1000 {
			compatible = "nxp,lpc1850-dac";
			reg = <0x400e1000 0x1000>;
			interrupts = <0>;
			clocks = <&ccu1 CLK_APB3_DAC>;
			resets = <&rgu 42>;
			status = "disabled";
		};

		can0: can@400e2000 {
			compatible = "bosch,c_can";
			reg = <0x400e2000 0x1000>;
			interrupts = <51>;
			clocks = <&ccu1 CLK_APB3_CAN0>;
			resets = <&rgu 55>;
			status = "disabled";
		};

		adc0: adc@400e3000 {
			compatible = "nxp,lpc1850-adc";
			reg = <0x400e3000 0x1000>;
			interrupts = <17>;
			clocks = <&ccu1 CLK_APB3_ADC0>;
			resets = <&rgu 40>;
			status = "disabled";
		};

		adc1: adc@400e4000 {
			compatible = "nxp,lpc1850-adc";
			reg = <0x400e4000 0x1000>;
			interrupts = <21>;
			clocks = <&ccu1 CLK_APB3_ADC1>;
			resets = <&rgu 41>;
			status = "disabled";
		};

		gpio: gpio@400f4000 {
			compatible = "nxp,lpc1850-gpio";
			reg = <0x400f4000 0x4000>;
			clocks = <&ccu1 CLK_CPU_GPIO>;
			gpio-controller;
			#gpio-cells = <2>;
			gpio-ranges =	<&pinctrl LPC_GPIO(0,0)  LPC_PIN(0,0)  2>,
					<&pinctrl LPC_GPIO(0,4)  LPC_PIN(1,0)  1>,
					<&pinctrl LPC_GPIO(0,8)  LPC_PIN(1,1)  4>,
					<&pinctrl LPC_GPIO(1,8)  LPC_PIN(1,5)  2>,
					<&pinctrl LPC_GPIO(1,0)  LPC_PIN(1,7)  8>,
					<&pinctrl LPC_GPIO(0,2)  LPC_PIN(1,15) 2>,
					<&pinctrl LPC_GPIO(0,12) LPC_PIN(1,17) 2>,
					<&pinctrl LPC_GPIO(0,15) LPC_PIN(1,20) 1>,
					<&pinctrl LPC_GPIO(5,0)  LPC_PIN(2,0)  7>,
					<&pinctrl LPC_GPIO(0,7)  LPC_PIN(2,7)  1>,
					<&pinctrl LPC_GPIO(5,7)  LPC_PIN(2,8)  1>,
					<&pinctrl LPC_GPIO(1,10) LPC_PIN(2,9)  1>,
					<&pinctrl LPC_GPIO(0,14) LPC_PIN(2,10) 1>,
					<&pinctrl LPC_GPIO(1,11) LPC_PIN(2,11) 3>,
					<&pinctrl LPC_GPIO(5,8)  LPC_PIN(3,1)  2>,
					<&pinctrl LPC_GPIO(1,14) LPC_PIN(3,4)  2>,
					<&pinctrl LPC_GPIO(0,6)  LPC_PIN(3,6)  1>,
					<&pinctrl LPC_GPIO(5,10) LPC_PIN(3,7)  2>,
					<&pinctrl LPC_GPIO(2,0)  LPC_PIN(4,0)  7>,
					<&pinctrl LPC_GPIO(5,12) LPC_PIN(4,8)  3>,
					<&pinctrl LPC_GPIO(2,9)  LPC_PIN(5,0)  7>,
					<&pinctrl LPC_GPIO(2,7)  LPC_PIN(5,7)  1>,
					<&pinctrl LPC_GPIO(3,0)  LPC_PIN(6,1)  5>,
					<&pinctrl LPC_GPIO(0,5)  LPC_PIN(6,6)  1>,
					<&pinctrl LPC_GPIO(5,15) LPC_PIN(6,7)  2>,
					<&pinctrl LPC_GPIO(3,5)  LPC_PIN(6,9)  3>,
					<&pinctrl LPC_GPIO(2,8)  LPC_PIN(6,12) 1>,
					<&pinctrl LPC_GPIO(3,8)  LPC_PIN(7,0)  8>,
					<&pinctrl LPC_GPIO(4,0)  LPC_PIN(8,0)  8>,
					<&pinctrl LPC_GPIO(4,12) LPC_PIN(9,0)  4>,
					<&pinctrl LPC_GPIO(5,17) LPC_PIN(9,4)  2>,
					<&pinctrl LPC_GPIO(4,11) LPC_PIN(9,6)  1>,
					<&pinctrl LPC_GPIO(4,8)  LPC_PIN(a,1)  3>,
					<&pinctrl LPC_GPIO(5,19) LPC_PIN(a,4)  1>,
					<&pinctrl LPC_GPIO(5,20) LPC_PIN(b,0)  7>,
					<&pinctrl LPC_GPIO(6,0)  LPC_PIN(c,1) 14>,
					<&pinctrl LPC_GPIO(6,14) LPC_PIN(d,0) 17>,
					<&pinctrl LPC_GPIO(7,0)  LPC_PIN(e,0) 16>,
					<&pinctrl LPC_GPIO(7,16) LPC_PIN(f,1)  3>,
					<&pinctrl LPC_GPIO(7,19) LPC_PIN(f,5)  7>;
		};
	};
};
Commit	Line	Data
804a5dd6 JE	1	/*
	2	* Common base for NXP LPC18xx and LPC43xx devices.
	3	*
	4	* Copyright 2015 Joachim Eastwood <manabian@gmail.com>
	5	*
	6	* This code is released using a dual license strategy: BSD/GPL
	7	* You can choose the licence that better fits your requirements.
	8	*
	9	* Released under the terms of 3-clause BSD License
	10	* Released under the terms of GNU General Public License Version 2.0
	11	*
	12	*/
	13
	14	#include "armv7-m.dtsi"
	15
ba2db535 JE	16	#include "dt-bindings/clock/lpc18xx-cgu.h"
	17	#include "dt-bindings/clock/lpc18xx-ccu.h"
	18
7836dce4 JE	19	#define LPC_PIN(port, pin) (0x##port * 32 + pin)
	20	#define LPC_GPIO(port, pin) (port * 32 + pin)
	21
804a5dd6 JE	22	/ {
	23	cpus {
	24	#address-cells = <1>;
	25	#size-cells = <0>;
	26
	27	cpu@0 {
	28	compatible = "arm,cortex-m3";
	29	device_type = "cpu";
	30	reg = <0x0>;
ba2db535	31	clocks = <&ccu1 CLK_CPU_CORE>;
804a5dd6 JE	32	};
	33	};
	34
	35	clocks {
	36	xtal: xtal {
	37	compatible = "fixed-clock";
	38	#clock-cells = <0>;
	39	clock-frequency = <12000000>;
	40	};
	41
ba2db535 JE	42	xtal32: xtal32 {
	43	compatible = "fixed-clock";
	44	#clock-cells = <0>;
	45	clock-frequency = <32768>;
	46	};
	47
	48	enet_rx_clk: enet_rx_clk {
	49	compatible = "fixed-clock";
	50	#clock-cells = <0>;
	51	clock-frequency = <0>;
	52	clock-output-names = "enet_rx_clk";
	53	};
	54
	55	enet_tx_clk: enet_tx_clk {
	56	compatible = "fixed-clock";
	57	#clock-cells = <0>;
	58	clock-frequency = <0>;
	59	clock-output-names = "enet_tx_clk";
	60	};
	61
	62	gp_clkin: gp_clkin {
	63	compatible = "fixed-clock";
804a5dd6	64	#clock-cells = <0>;
ba2db535 JE	65	clock-frequency = <0>;
ba2db535 JE	66	clock-output-names = "gp_clkin";
804a5dd6 JE	67	};
	68	};
	69
	70	soc {
b8da65d1 AA	71	sct_pwm: pwm@40000000 {
	72	compatible = "nxp,lpc1850-sct-pwm";
	73	reg = <0x40000000 0x1000>;
	74	clocks =<&ccu1 CLK_CPU_SCT>;
	75	clock-names = "pwm";
	76	resets = <&rgu 37>;
	77	#pwm-cells = <3>;
	78	status = "disabled";
	79	};
	80
5924007c JE	81	dmac: dma-controller@40002000 {
	82	compatible = "arm,pl080", "arm,primecell";
	83	arm,primecell-periphid = <0x00041080>;
	84	reg = <0x40002000 0x1000>;
	85	interrupts = <2>;
	86	clocks = <&ccu1 CLK_CPU_DMA>;
	87	clock-names = "apb_pclk";
	88	resets = <&rgu 19>;
	89	#dma-cells = <2>;
	90	dma-channels = <8>;
	91	dma-requests = <16>;
	92	lli-bus-interface-ahb1;
	93	lli-bus-interface-ahb2;
	94	mem-bus-interface-ahb1;
	95	mem-bus-interface-ahb2;
	96	memcpy-burst-size = <256>;
	97	memcpy-bus-width = <32>;
	98	};
	99
4f85dd16 JE	100	spifi: flash-controller@40003000 {
	101	compatible = "nxp,lpc1773-spifi";
	102	reg = <0x40003000 0x1000>, <0x14000000 0x4000000>;
	103	reg-names = "spifi", "flash";
	104	interrupts = <30>;
	105	clocks = <&ccu1 CLK_SPIFI>, <&ccu1 CLK_CPU_SPIFI>;
	106	clock-names = "spifi", "reg";
	107	resets = <&rgu 53>;
	108	status = "disabled";
	109	};
	110
cd07154f JE	111	mmcsd: mmcsd@40004000 {
	112	compatible = "snps,dw-mshc";
	113	reg = <0x40004000 0x1000>;
	114	interrupts = <6>;
	115	num-slots = <1>;
	116	clocks = <&ccu2 CLK_SDIO>, <&ccu1 CLK_CPU_SDIO>;
	117	clock-names = "ciu", "biu";
2300830f	118	resets = <&rgu 20>;
cd07154f JE	119	status = "disabled";
	120	};
	121
b06cdb79 JE	122	usb0: ehci@40006100 {
	123	compatible = "nxp,lpc1850-ehci", "generic-ehci";
	124	reg = <0x40006100 0x100>;
	125	interrupts = <8>;
	126	clocks = <&ccu1 CLK_CPU_USB0>;
2300830f	127	resets = <&rgu 17>;
6d6d6b55 JE	128	phys = <&usb0_otg_phy>;
6d6d6b55 JE	129	phy-names = "usb";
b06cdb79 JE	130	has-transaction-translator;
	131	status = "disabled";
	132	};
	133
	134	usb1: ehci@40007100 {
	135	compatible = "nxp,lpc1850-ehci", "generic-ehci";
	136	reg = <0x40007100 0x100>;
	137	interrupts = <9>;
	138	clocks = <&ccu1 CLK_CPU_USB1>;
2300830f	139	resets = <&rgu 18>;
b06cdb79 JE	140	status = "disabled";
	141	};
	142
50016385 JE	143	emc: memory-controller@40005000 {
	144	compatible = "arm,pl172", "arm,primecell";
	145	reg = <0x40005000 0x1000>;
	146	clocks = <&ccu1 CLK_CPU_EMCDIV>, <&ccu1 CLK_CPU_EMC>;
	147	clock-names = "mpmcclk", "apb_pclk";
2300830f	148	resets = <&rgu 21>;
50016385 JE	149	#address-cells = <2>;
	150	#size-cells = <1>;
	151	ranges = <0 0 0x1c000000 0x1000000
	152	1 0 0x1d000000 0x1000000
	153	2 0 0x1e000000 0x1000000
	154	3 0 0x1f000000 0x1000000>;
	155	status = "disabled";
	156	};
	157
9cf6267d JE	158	lcdc: lcd-controller@40008000 {
	159	compatible = "arm,pl111", "arm,primecell";
	160	reg = <0x40008000 0x1000>;
	161	interrupts = <7>;
	162	interrupt-names = "combined";
	163	clocks = <&cgu BASE_LCD_CLK>, <&ccu1 CLK_CPU_LCD>;
	164	clock-names = "clcdclk", "apb_pclk";
2300830f	165	resets = <&rgu 16>;
9cf6267d JE	166	status = "disabled";
	167	};
	168
5c36aa6f AA	169	eeprom: eeprom@4000e000 {
	170	compatible = "nxp,lpc1857-eeprom";
	171	reg = <0x4000e000 0x1000>, <0x20040000 0x4000>;
	172	reg-names = "reg", "mem";
	173	clocks = <&ccu1 CLK_CPU_EEPROM>;
	174	clock-names = "eeprom";
	175	resets = <&rgu 27>;
	176	interrupts = <4>;
	177	status = "disabled";
	178	};
	179
fe968589 JE	180	mac: ethernet@40010000 {
	181	compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac";
	182	reg = <0x40010000 0x2000>;
	183	interrupts = <5>;
	184	interrupt-names = "macirq";
	185	clocks = <&ccu1 CLK_CPU_ETHERNET>;
	186	clock-names = "stmmaceth";
2300830f JE	187	resets = <&rgu 22>;
2300830f JE	188	reset-names = "stmmaceth";
fe968589 JE	189	status = "disabled";
	190	};
	191
16df2b86 JE	192	creg: syscon@40043000 {
	193	compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd";
	194	reg = <0x40043000 0x1000>;
	195	clocks = <&ccu1 CLK_CPU_CREG>;
2300830f	196	resets = <&rgu 5>;
6d6d6b55	197
52d7c426 JE	198	creg_clk: clock-controller {
	199	compatible = "nxp,lpc1850-creg-clk";
	200	clocks = <&xtal32>;
	201	#clock-cells = <1>;
	202	};
	203
472a5a3d	204	usb0_otg_phy: phy {
6d6d6b55 JE	205	compatible = "nxp,lpc1850-usb-otg-phy";
	206	clocks = <&ccu1 CLK_USB0>;
	207	#phy-cells = <0>;
	208	};
5913f559	209
472a5a3d	210	dmamux: dma-mux {
5913f559 JE	211	compatible = "nxp,lpc1850-dmamux";
	212	#dma-cells = <3>;
	213	dma-requests = <64>;
	214	dma-masters = <&dmac>;
	215	};
16df2b86 JE	216	};
16df2b86 JE	217
246fee6c JE	218	rtc: rtc@40046000 {
	219	compatible = "nxp,lpc1850-rtc", "nxp,lpc1788-rtc";
	220	reg = <0x40046000 0x1000>;
	221	interrupts = <47>;
	222	clocks = <&creg_clk 0>, <&ccu1 CLK_CPU_BUS>;
	223	clock-names = "rtc", "reg";
	224	};
	225
ba2db535 JE	226	cgu: clock-controller@40050000 {
	227	compatible = "nxp,lpc1850-cgu";
	228	reg = <0x40050000 0x1000>;
	229	#clock-cells = <1>;
52d7c426	230	clocks = <&xtal>, <&creg_clk 1>, <&enet_rx_clk>, <&enet_tx_clk>, <&gp_clkin>;
ba2db535 JE	231	};
	232
	233	ccu1: clock-controller@40051000 {
	234	compatible = "nxp,lpc1850-ccu";
	235	reg = <0x40051000 0x1000>;
	236	#clock-cells = <1>;
	237	clocks = <&cgu BASE_APB3_CLK>, <&cgu BASE_APB1_CLK>,
	238	<&cgu BASE_SPIFI_CLK>, <&cgu BASE_CPU_CLK>,
	239	<&cgu BASE_PERIPH_CLK>, <&cgu BASE_USB0_CLK>,
	240	<&cgu BASE_USB1_CLK>, <&cgu BASE_SPI_CLK>;
	241	clock-names = "base_apb3_clk", "base_apb1_clk",
	242	"base_spifi_clk", "base_cpu_clk",
	243	"base_periph_clk", "base_usb0_clk",
	244	"base_usb1_clk", "base_spi_clk";
	245	};
	246
	247	ccu2: clock-controller@40052000 {
	248	compatible = "nxp,lpc1850-ccu";
	249	reg = <0x40052000 0x1000>;
	250	#clock-cells = <1>;
	251	clocks = <&cgu BASE_AUDIO_CLK>, <&cgu BASE_UART3_CLK>,
	252	<&cgu BASE_UART2_CLK>, <&cgu BASE_UART1_CLK>,
	253	<&cgu BASE_UART0_CLK>, <&cgu BASE_SSP1_CLK>,
	254	<&cgu BASE_SSP0_CLK>, <&cgu BASE_SDIO_CLK>;
	255	clock-names = "base_audio_clk", "base_uart3_clk",
	256	"base_uart2_clk", "base_uart1_clk",
	257	"base_uart0_clk", "base_ssp1_clk",
	258	"base_ssp0_clk", "base_sdio_clk";
	259	};
	260
0745c702 JE	261	rgu: reset-controller@40053000 {
	262	compatible = "nxp,lpc1850-rgu";
	263	reg = <0x40053000 0x1000>;
	264	clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_BUS>;
	265	clock-names = "delay", "reg";
	266	#reset-cells = <1>;
	267	};
	268
9c8a5cdc AA	269	watchdog@40080000 {
	270	compatible = "nxp,lpc1850-wwdt";
	271	reg = <0x40080000 0x24>;
	272	interrupts = <49>;
	273	clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_WWDT>;
	274	clock-names = "wdtclk", "reg";
	275	};
	276
804a5dd6	277	uart0: serial@40081000 {
f2b1c507	278	compatible = "nxp,lpc1850-uart", "ns16550a";
804a5dd6 JE	279	reg = <0x40081000 0x1000>;
	280	reg-shift = <2>;
	281	interrupts = <24>;
ba2db535	282	clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>;
f2b1c507	283	clock-names = "uartclk", "reg";
2300830f	284	resets = <&rgu 44>;
4e9c5aa8 JE	285	dmas = <&dmamux 1 1 2
	286	&dmamux 2 1 2
	287	&dmamux 11 2 2
	288	&dmamux 12 2 2>;
	289	dma-names = "tx", "rx", "tx", "rx";
804a5dd6 JE	290	status = "disabled";
	291	};
	292
	293	uart1: serial@40082000 {
f2b1c507	294	compatible = "nxp,lpc1850-uart", "ns16550a";
804a5dd6 JE	295	reg = <0x40082000 0x1000>;
	296	reg-shift = <2>;
	297	interrupts = <25>;
ba2db535	298	clocks = <&ccu2 CLK_APB0_UART1>, <&ccu1 CLK_CPU_UART1>;
f2b1c507	299	clock-names = "uartclk", "reg";
2300830f	300	resets = <&rgu 45>;
4e9c5aa8 JE	301	dmas = <&dmamux 3 1 2
	302	&dmamux 4 1 2>;
	303	dma-names = "tx", "rx";
804a5dd6 JE	304	status = "disabled";
	305	};
	306
5d2ea79c JE	307	ssp0: spi@40083000 {
	308	compatible = "arm,pl022", "arm,primecell";
	309	reg = <0x40083000 0x1000>;
	310	interrupts = <22>;
	311	clocks = <&ccu2 CLK_APB0_SSP0>, <&ccu1 CLK_CPU_SSP0>;
	312	clock-names = "sspclk", "apb_pclk";
2300830f	313	resets = <&rgu 50>;
c5288091 JE	314	dmas = <&dmamux 9 0 2
	315	&dmamux 10 0 2>;
	316	dma-names = "rx", "tx";
5d2ea79c JE	317	#address-cells = <1>;
	318	#size-cells = <0>;
	319	status = "disabled";
	320	};
	321
804a5dd6 JE	322	timer0: timer@40084000 {
	323	compatible = "nxp,lpc3220-timer";
	324	reg = <0x40084000 0x1000>;
	325	interrupts = <12>;
ba2db535	326	clocks = <&ccu1 CLK_CPU_TIMER0>;
804a5dd6	327	clock-names = "timerclk";
2300830f	328	resets = <&rgu 32>;
804a5dd6 JE	329	};
	330
	331	timer1: timer@40085000 {
	332	compatible = "nxp,lpc3220-timer";
	333	reg = <0x40085000 0x1000>;
	334	interrupts = <13>;
ba2db535	335	clocks = <&ccu1 CLK_CPU_TIMER1>;
804a5dd6	336	clock-names = "timerclk";
2300830f	337	resets = <&rgu 33>;
804a5dd6 JE	338	};
804a5dd6 JE	339
d881f5e2 JE	340	pinctrl: pinctrl@40086000 {
	341	compatible = "nxp,lpc1850-scu";
	342	reg = <0x40086000 0x1000>;
	343	clocks = <&ccu1 CLK_CPU_SCU>;
	344	};
	345
06713a94 JE	346	i2c0: i2c@400a1000 {
	347	compatible = "nxp,lpc1788-i2c";
	348	reg = <0x400a1000 0x1000>;
	349	interrupts = <18>;
	350	clocks = <&ccu1 CLK_APB1_I2C0>;
	351	resets = <&rgu 48>;
	352	#address-cells = <1>;
	353	#size-cells = <0>;
	354	status = "disabled";
	355	};
	356
7e6c8376 JE	357	can1: can@400a4000 {
	358	compatible = "bosch,c_can";
	359	reg = <0x400a4000 0x1000>;
	360	interrupts = <43>;
	361	clocks = <&ccu1 CLK_APB1_CAN1>;
2300830f	362	resets = <&rgu 54>;
7e6c8376 JE	363	status = "disabled";
	364	};
	365
804a5dd6	366	uart2: serial@400c1000 {
f2b1c507	367	compatible = "nxp,lpc1850-uart", "ns16550a";
804a5dd6 JE	368	reg = <0x400c1000 0x1000>;
	369	reg-shift = <2>;
	370	interrupts = <26>;
ba2db535	371	clocks = <&ccu2 CLK_APB2_UART2>, <&ccu1 CLK_CPU_UART2>;
f2b1c507	372	clock-names = "uartclk", "reg";
2300830f	373	resets = <&rgu 46>;
4e9c5aa8 JE	374	dmas = <&dmamux 5 1 2
	375	&dmamux 6 1 2>;
	376	dma-names = "tx", "rx";
804a5dd6 JE	377	status = "disabled";
	378	};
	379
	380	uart3: serial@400c2000 {
f2b1c507	381	compatible = "nxp,lpc1850-uart", "ns16550a";
804a5dd6 JE	382	reg = <0x400c2000 0x1000>;
	383	reg-shift = <2>;
	384	interrupts = <27>;
ba2db535	385	clocks = <&ccu2 CLK_APB2_UART3>, <&ccu1 CLK_CPU_UART3>;
f2b1c507	386	clock-names = "uartclk", "reg";
2300830f	387	resets = <&rgu 47>;
4e9c5aa8 JE	388	dmas = <&dmamux 7 1 2
	389	&dmamux 8 1 2
	390	&dmamux 13 3 2
	391	&dmamux 14 3 2>;
	392	dma-names = "tx", "rx", "rx", "tx";
804a5dd6 JE	393	status = "disabled";
	394	};
	395
	396	timer2: timer@400c3000 {
	397	compatible = "nxp,lpc3220-timer";
	398	reg = <0x400c3000 0x1000>;
	399	interrupts = <14>;
ba2db535	400	clocks = <&ccu1 CLK_CPU_TIMER2>;
804a5dd6	401	clock-names = "timerclk";
2300830f	402	resets = <&rgu 34>;
804a5dd6 JE	403	};
	404
	405	timer3: timer@400c4000 {
	406	compatible = "nxp,lpc3220-timer";
	407	reg = <0x400c4000 0x1000>;
	408	interrupts = <15>;
ba2db535	409	clocks = <&ccu1 CLK_CPU_TIMER3>;
804a5dd6	410	clock-names = "timerclk";
2300830f	411	resets = <&rgu 35>;
804a5dd6	412	};
7836dce4	413
5d2ea79c JE	414	ssp1: spi@400c5000 {
	415	compatible = "arm,pl022", "arm,primecell";
	416	reg = <0x400c5000 0x1000>;
	417	interrupts = <23>;
	418	clocks = <&ccu2 CLK_APB2_SSP1>, <&ccu1 CLK_CPU_SSP1>;
	419	clock-names = "sspclk", "apb_pclk";
2300830f	420	resets = <&rgu 51>;
c5288091 JE	421	dmas = <&dmamux 11 2 2
	422	&dmamux 12 2 2
	423	&dmamux 3 3 2
	424	&dmamux 4 3 2
	425	&dmamux 5 2 2
	426	&dmamux 6 2 2
	427	&dmamux 13 2 2
	428	&dmamux 14 2 2>;
	429	dma-names = "rx", "tx", "tx", "rx",
	430	"tx", "rx", "rx", "tx";
5d2ea79c JE	431	#address-cells = <1>;
	432	#size-cells = <0>;
	433	status = "disabled";
	434	};
	435
06713a94 JE	436	i2c1: i2c@400e0000 {
	437	compatible = "nxp,lpc1788-i2c";
	438	reg = <0x400e0000 0x1000>;
	439	interrupts = <19>;
	440	clocks = <&ccu1 CLK_APB3_I2C1>;
	441	resets = <&rgu 49>;
	442	#address-cells = <1>;
	443	#size-cells = <0>;
	444	status = "disabled";
	445	};
	446
8c938004 JE	447	dac: dac@400e1000 {
	448	compatible = "nxp,lpc1850-dac";
	449	reg = <0x400e1000 0x1000>;
	450	interrupts = <0>;
	451	clocks = <&ccu1 CLK_APB3_DAC>;
	452	resets = <&rgu 42>;
	453	status = "disabled";
	454	};
	455
7e6c8376 JE	456	can0: can@400e2000 {
	457	compatible = "bosch,c_can";
	458	reg = <0x400e2000 0x1000>;
	459	interrupts = <51>;
	460	clocks = <&ccu1 CLK_APB3_CAN0>;
2300830f	461	resets = <&rgu 55>;
7e6c8376 JE	462	status = "disabled";
	463	};
	464
e162f9c2 JE	465	adc0: adc@400e3000 {
	466	compatible = "nxp,lpc1850-adc";
	467	reg = <0x400e3000 0x1000>;
	468	interrupts = <17>;
	469	clocks = <&ccu1 CLK_APB3_ADC0>;
	470	resets = <&rgu 40>;
	471	status = "disabled";
	472	};
	473
	474	adc1: adc@400e4000 {
	475	compatible = "nxp,lpc1850-adc";
	476	reg = <0x400e4000 0x1000>;
	477	interrupts = <21>;
	478	clocks = <&ccu1 CLK_APB3_ADC1>;
	479	resets = <&rgu 41>;
	480	status = "disabled";
	481	};
	482
7836dce4 JE	483	gpio: gpio@400f4000 {
	484	compatible = "nxp,lpc1850-gpio";
	485	reg = <0x400f4000 0x4000>;
	486	clocks = <&ccu1 CLK_CPU_GPIO>;
	487	gpio-controller;
	488	#gpio-cells = <2>;
	489	gpio-ranges = <&pinctrl LPC_GPIO(0,0) LPC_PIN(0,0) 2>,
	490	<&pinctrl LPC_GPIO(0,4) LPC_PIN(1,0) 1>,
	491	<&pinctrl LPC_GPIO(0,8) LPC_PIN(1,1) 4>,
	492	<&pinctrl LPC_GPIO(1,8) LPC_PIN(1,5) 2>,
	493	<&pinctrl LPC_GPIO(1,0) LPC_PIN(1,7) 8>,
	494	<&pinctrl LPC_GPIO(0,2) LPC_PIN(1,15) 2>,
	495	<&pinctrl LPC_GPIO(0,12) LPC_PIN(1,17) 2>,
	496	<&pinctrl LPC_GPIO(0,15) LPC_PIN(1,20) 1>,
	497	<&pinctrl LPC_GPIO(5,0) LPC_PIN(2,0) 7>,
	498	<&pinctrl LPC_GPIO(0,7) LPC_PIN(2,7) 1>,
	499	<&pinctrl LPC_GPIO(5,7) LPC_PIN(2,8) 1>,
	500	<&pinctrl LPC_GPIO(1,10) LPC_PIN(2,9) 1>,
	501	<&pinctrl LPC_GPIO(0,14) LPC_PIN(2,10) 1>,
	502	<&pinctrl LPC_GPIO(1,11) LPC_PIN(2,11) 3>,
	503	<&pinctrl LPC_GPIO(5,8) LPC_PIN(3,1) 2>,
	504	<&pinctrl LPC_GPIO(1,14) LPC_PIN(3,4) 2>,
	505	<&pinctrl LPC_GPIO(0,6) LPC_PIN(3,6) 1>,
	506	<&pinctrl LPC_GPIO(5,10) LPC_PIN(3,7) 2>,
	507	<&pinctrl LPC_GPIO(2,0) LPC_PIN(4,0) 7>,
	508	<&pinctrl LPC_GPIO(5,12) LPC_PIN(4,8) 3>,
	509	<&pinctrl LPC_GPIO(2,9) LPC_PIN(5,0) 7>,
	510	<&pinctrl LPC_GPIO(2,7) LPC_PIN(5,7) 1>,
	511	<&pinctrl LPC_GPIO(3,0) LPC_PIN(6,1) 5>,
	512	<&pinctrl LPC_GPIO(0,5) LPC_PIN(6,6) 1>,
	513	<&pinctrl LPC_GPIO(5,15) LPC_PIN(6,7) 2>,
	514	<&pinctrl LPC_GPIO(3,5) LPC_PIN(6,9) 3>,
	515	<&pinctrl LPC_GPIO(2,8) LPC_PIN(6,12) 1>,
	516	<&pinctrl LPC_GPIO(3,8) LPC_PIN(7,0) 8>,
	517	<&pinctrl LPC_GPIO(4,0) LPC_PIN(8,0) 8>,
	518	<&pinctrl LPC_GPIO(4,12) LPC_PIN(9,0) 4>,
	519	<&pinctrl LPC_GPIO(5,17) LPC_PIN(9,4) 2>,
	520	<&pinctrl LPC_GPIO(4,11) LPC_PIN(9,6) 1>,
	521	<&pinctrl LPC_GPIO(4,8) LPC_PIN(a,1) 3>,
	522	<&pinctrl LPC_GPIO(5,19) LPC_PIN(a,4) 1>,
	523	<&pinctrl LPC_GPIO(5,20) LPC_PIN(b,0) 7>,
	524	<&pinctrl LPC_GPIO(6,0) LPC_PIN(c,1) 14>,
	525	<&pinctrl LPC_GPIO(6,14) LPC_PIN(d,0) 17>,
	526	<&pinctrl LPC_GPIO(7,0) LPC_PIN(e,0) 16>,
	527	<&pinctrl LPC_GPIO(7,16) LPC_PIN(f,1) 3>,
	528	<&pinctrl LPC_GPIO(7,19) LPC_PIN(f,5) 7>;
	529	};
804a5dd6 JE	530	};
804a5dd6 JE	531	};