[deliverable/linux.git] / arch / arm / boot / dts / omap3-n900.dts

/*
 * Copyright (C) 2013 Pavel Machek <pavel@ucw.cz>
 * Copyright (C) 2013-2014 Aaro Koskinen <aaro.koskinen@iki.fi>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 (or later) as
 * published by the Free Software Foundation.
 */

/dts-v1/;

#include "omap34xx-hs.dtsi"

/ {
	model = "Nokia N900";
	compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3";

	cpus {
		cpu@0 {
			cpu0-supply = <&vcc>;
		};
	};

	leds {
		compatible = "gpio-leds";
		heartbeat {
			label = "debug::sleep";
			gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;  /* gpio162 */
			linux,default-trigger = "default-on";
			pinctrl-names = "default";
			pinctrl-0 = <&debug_leds>;
		};
	};

	memory {
		device_type = "memory";
		reg = <0x80000000 0x10000000>; /* 256 MB */
	};

	gpio_keys {
		compatible = "gpio-keys";

		camera_lens_cover {
			label = "Camera Lens Cover";
			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
			linux,input-type = <5>; /* EV_SW */
			linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */
			gpio-key,wakeup;
		};

		camera_focus {
			label = "Camera Focus";
			gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
			linux,code = <0x210>; /* KEY_CAMERA_FOCUS */
			gpio-key,wakeup;
		};

		camera_capture {
			label = "Camera Capture";
			gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
			linux,code = <0xd4>; /* KEY_CAMERA */
			gpio-key,wakeup;
		};

		lock_button {
			label = "Lock Button";
			gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
			linux,code = <0x98>; /* KEY_SCREENLOCK */
			gpio-key,wakeup;
		};

		keypad_slide {
			label = "Keypad Slide";
			gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
			linux,input-type = <5>; /* EV_SW */
			linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */
			gpio-key,wakeup;
		};

		proximity_sensor {
			label = "Proximity Sensor";
			gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
			linux,input-type = <5>; /* EV_SW */
			linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */
		};
	};

	isp1704: isp1704 {
		compatible = "nxp,isp1704";
		nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
		usb-phy = <&usb2_phy>;
	};

	tv: connector {
		compatible = "composite-connector";
		label = "tv";

		port {
			tv_connector_in: endpoint {
				remote-endpoint = <&venc_out>;
			};
		};
	};
};

&omap3_pmx_core {
	pinctrl-names = "default";

	uart2_pins: pinmux_uart2_pins {
		pinctrl-single,pins = <
			0x14a (PIN_INPUT | MUX_MODE0)		/* uart2_rx */
			0x148 (PIN_OUTPUT | MUX_MODE0)		/* uart2_tx */
		>;
	};

	uart3_pins: pinmux_uart3_pins {
		pinctrl-single,pins = <
			0x16e (PIN_INPUT | MUX_MODE0)		/* uart3_rx */
			0x170 (PIN_OUTPUT | MUX_MODE0)		/* uart3_tx */
		>;
	};

	i2c1_pins: pinmux_i2c1_pins {
		pinctrl-single,pins = <
			0x18a (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
		>;
	};

	i2c2_pins: pinmux_i2c2_pins {
		pinctrl-single,pins = <
			0x18e (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_scl */
			0x190 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_sda */
		>;
	};

	i2c3_pins: pinmux_i2c3_pins {
		pinctrl-single,pins = <
			0x192 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_scl */
			0x194 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_sda */
		>;
	};

	debug_leds: pinmux_debug_led_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)	/* mcbsp1_clkx.gpio_162 */
		>;
	};

	mmc1_pins: pinmux_mmc1_pins {
		pinctrl-single,pins = <
			0x114 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk */
			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd */
			0x118 (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat0 */
			0x11a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat1 */
			0x11c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat2 */
			0x11e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat3 */
		>;
	};

	mmc2_pins: pinmux_mmc2_pins {
		pinctrl-single,pins = <
			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk */
			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd */
			0x12c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc2_dat0 */
			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1 */
			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2 */
			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3 */
			0x134 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat4 */
			0x136 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat5 */
			0x138 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat6 */
			0x13a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat7 */
		>;
	};

	acx565akm_pins: pinmux_acx565akm_pins {
		pinctrl-single,pins = <
			0x0d4 (PIN_OUTPUT | MUX_MODE4)		/* RX51_LCD_RESET_GPIO */
		>;
	};

	dss_sdi_pins: pinmux_dss_sdi_pins {
		pinctrl-single,pins = <
			0x0c0 (PIN_OUTPUT | MUX_MODE1)   /* dss_data10.sdi_dat1n */
			0x0c2 (PIN_OUTPUT | MUX_MODE1)   /* dss_data11.sdi_dat1p */
			0x0c4 (PIN_OUTPUT | MUX_MODE1)   /* dss_data12.sdi_dat2n */
			0x0c6 (PIN_OUTPUT | MUX_MODE1)   /* dss_data13.sdi_dat2p */

			0x0d8 (PIN_OUTPUT | MUX_MODE1)   /* dss_data22.sdi_clkp */
			0x0da (PIN_OUTPUT | MUX_MODE1)   /* dss_data23.sdi_clkn */
		>;
	};
};

&i2c1 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c1_pins>;

	clock-frequency = <2200000>;

	twl: twl@48 {
		reg = <0x48>;
		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
		interrupt-parent = <&intc>;
	};
};

#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"

&vaux1 {
	regulator-name = "V28";
	regulator-min-microvolt = <2800000>;
	regulator-max-microvolt = <2800000>;
	regulator-always-on; /* due battery cover sensor */
};

&vaux2 {
	regulator-name = "VCSI";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
};

&vaux3 {
	regulator-name = "VMMC2_30";
	regulator-min-microvolt = <2800000>;
	regulator-max-microvolt = <3000000>;
};

&vaux4 {
	regulator-name = "VCAM_ANA_28";
	regulator-min-microvolt = <2800000>;
	regulator-max-microvolt = <2800000>;
};

&vmmc1 {
	regulator-name = "VMMC1";
	regulator-min-microvolt = <1850000>;
	regulator-max-microvolt = <3150000>;
};

&vmmc2 {
	regulator-name = "V28_A";
	regulator-min-microvolt = <2800000>;
	regulator-max-microvolt = <3000000>;
	regulator-always-on; /* due VIO leak to AIC34 VDDs */
};

&vpll1 {
	regulator-name = "VPLL";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-always-on;
};

&vpll2 {
	regulator-name = "VSDI_CSI";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-always-on;
};

&vsim {
	regulator-name = "VMMC2_IO_18";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
};

&vio {
	regulator-name = "VIO";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;

};

&vintana1 {
	regulator-name = "VINTANA1";
	/* fixed to 1500000 */
	regulator-always-on;
};

&vintana2 {
	regulator-name = "VINTANA2";
	regulator-min-microvolt = <2750000>;
	regulator-max-microvolt = <2750000>;
	regulator-always-on;
};

&vintdig {
	regulator-name = "VINTDIG";
	/* fixed to 1500000 */
	regulator-always-on;
};

&twl {
	twl_audio: audio {
		compatible = "ti,twl4030-audio";
		ti,enable-vibra = <1>;
	};
};

&twl_keypad {
	linux,keymap = < 0x00000010 /* KEY_Q */
			 0x00010018 /* KEY_O */
			 0x00020019 /* KEY_P */
			 0x00030033 /* KEY_COMMA */
			 0x0004000e /* KEY_BACKSPACE */
			 0x0006001e /* KEY_A */
			 0x0007001f /* KEY_S */

			 0x01000011 /* KEY_W */
			 0x01010020 /* KEY_D */
			 0x01020021 /* KEY_F */
			 0x01030022 /* KEY_G */
			 0x01040023 /* KEY_H */
			 0x01050024 /* KEY_J */
			 0x01060025 /* KEY_K */
			 0x01070026 /* KEY_L */

			 0x02000012 /* KEY_E */
			 0x02010034 /* KEY_DOT */
			 0x02020067 /* KEY_UP */
			 0x0203001c /* KEY_ENTER */
			 0x0205002c /* KEY_Z */
			 0x0206002d /* KEY_X */
			 0x0207002e /* KEY_C */
			 0x02080043 /* KEY_F9 */

			 0x03000013 /* KEY_R */
			 0x0301002f /* KEY_V */
			 0x03020030 /* KEY_B */
			 0x03030031 /* KEY_N */
			 0x03040032 /* KEY_M */
			 0x03050039 /* KEY_SPACE */
			 0x03060039 /* KEY_SPACE */
			 0x03070069 /* KEY_LEFT */

			 0x04000014 /* KEY_T */
			 0x0401006c /* KEY_DOWN */
			 0x0402006a /* KEY_RIGHT */
			 0x0404001d /* KEY_LEFTCTRL */
			 0x04050064 /* KEY_RIGHTALT */
			 0x0406002a /* KEY_LEFTSHIFT */
			 0x04080044 /* KEY_F10 */

			 0x05000015 /* KEY_Y */
			 0x05080057 /* KEY_F11 */

			 0x06000016 /* KEY_U */

			 0x07000017 /* KEY_I */
			 0x07010041 /* KEY_F7 */
			 0x07020042 /* KEY_F8 */
			 >;
};

&twl_gpio {
	ti,pullups	= <0x0>;
	ti,pulldowns	= <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
};

&i2c2 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c2_pins>;

	clock-frequency = <100000>;

	tlv320aic3x: tlv320aic3x@18 {
		compatible = "ti,tlv320aic3x";
		reg = <0x18>;
		gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
		ai3x-gpio-func = <
			0 /* AIC3X_GPIO1_FUNC_DISABLED */
			5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
		>;

		AVDD-supply = <&vmmc2>;
		DRVDD-supply = <&vmmc2>;
		IOVDD-supply = <&vio>;
		DVDD-supply = <&vio>;
	};

	tlv320aic3x_aux: tlv320aic3x@19 {
		compatible = "ti,tlv320aic3x";
		reg = <0x19>;
		gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */

		AVDD-supply = <&vmmc2>;
		DRVDD-supply = <&vmmc2>;
		IOVDD-supply = <&vio>;
		DVDD-supply = <&vio>;
	};

	tsl2563: tsl2563@29 {
		compatible = "amstaos,tsl2563";
		reg = <0x29>;

		amstaos,cover-comp-gain = <16>;
	};

	lp5523: lp5523@32 {
		compatible = "national,lp5523";
		reg = <0x32>;
		clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
		enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */

		chan0 {
			chan-name = "lp5523:kb1";
			led-cur = /bits/ 8 <50>;
			max-cur = /bits/ 8 <100>;
		};

		chan1 {
			chan-name = "lp5523:kb2";
			led-cur = /bits/ 8 <50>;
			max-cur = /bits/ 8 <100>;
		};

		chan2 {
			chan-name = "lp5523:kb3";
			led-cur = /bits/ 8 <50>;
			max-cur = /bits/ 8 <100>;
		};

		chan3 {
			chan-name = "lp5523:kb4";
			led-cur = /bits/ 8 <50>;
			max-cur = /bits/ 8 <100>;
		};

		chan4 {
			chan-name = "lp5523:b";
			led-cur = /bits/ 8 <50>;
			max-cur = /bits/ 8 <100>;
		};

		chan5 {
			chan-name = "lp5523:g";
			led-cur = /bits/ 8 <50>;
			max-cur = /bits/ 8 <100>;
		};

		chan6 {
			chan-name = "lp5523:r";
			led-cur = /bits/ 8 <50>;
			max-cur = /bits/ 8 <100>;
		};

		chan7 {
			chan-name = "lp5523:kb5";
			led-cur = /bits/ 8 <50>;
			max-cur = /bits/ 8 <100>;
		};

		chan8 {
			chan-name = "lp5523:kb6";
			led-cur = /bits/ 8 <50>;
			max-cur = /bits/ 8 <100>;
		};
	};

	bq27200: bq27200@55 {
		compatible = "ti,bq27200";
		reg = <0x55>;
	};

	tpa6130a2: tpa6130a2@60 {
		compatible = "ti,tpa6130a2";
		reg = <0x60>;

		Vdd-supply = <&vmmc2>;

		power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */
	};

	bq24150a: bq24150a@6b {
		compatible = "ti,bq24150a";
		reg = <0x6b>;

		ti,current-limit = <100>;
		ti,weak-battery-voltage = <3400>;
		ti,battery-regulation-voltage = <4200>;
		ti,charge-current = <650>;
		ti,termination-current = <100>;
		ti,resistor-sense = <68>;

		ti,usb-charger-detection = <&isp1704>;
	};
};

&i2c3 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c3_pins>;

	clock-frequency = <400000>;
};

&mmc1 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc1_pins>;
	vmmc-supply = <&vmmc1>;
	bus-width = <4>;
	cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
};

/* most boards use vaux3, only some old versions use vmmc2 instead */
&mmc2 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc2_pins>;
	vmmc-supply = <&vaux3>;
	vmmc_aux-supply = <&vsim>;
	bus-width = <8>;
	non-removable;
};

&mmc3 {
	status = "disabled";
};

&gpmc {
	ranges = <0 0 0x04000000 0x10000000>; /* 256MB */

	/* gpio-irq for dma: 65 */

	onenand@0,0 {
		#address-cells = <1>;
		#size-cells = <1>;
		reg = <0 0 0x10000000>;

		gpmc,sync-read;
		gpmc,sync-write;
		gpmc,burst-length = <16>;
		gpmc,burst-read;
		gpmc,burst-wrap;
		gpmc,burst-write;
		gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
		gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
		gpmc,cs-on-ns = <0>;
		gpmc,cs-rd-off-ns = <87>;
		gpmc,cs-wr-off-ns = <87>;
		gpmc,adv-on-ns = <0>;
		gpmc,adv-rd-off-ns = <10>;
		gpmc,adv-wr-off-ns = <10>;
		gpmc,oe-on-ns = <15>;
		gpmc,oe-off-ns = <87>;
		gpmc,we-on-ns = <0>;
		gpmc,we-off-ns = <87>;
		gpmc,rd-cycle-ns = <112>;
		gpmc,wr-cycle-ns = <112>;
		gpmc,access-ns = <81>;
		gpmc,page-burst-access-ns = <15>;
		gpmc,bus-turnaround-ns = <0>;
		gpmc,cycle2cycle-delay-ns = <0>;
		gpmc,wait-monitoring-ns = <0>;
		gpmc,clk-activation-ns = <5>;
		gpmc,wr-data-mux-bus-ns = <30>;
		gpmc,wr-access-ns = <81>;
		gpmc,sync-clk-ps = <15000>;

		/*
		 * MTD partition table corresponding to Nokia's
		 * Maemo 5 (Fremantle) release.
		 */
		partition@0 {
			label = "bootloader";
			reg = <0x00000000 0x00020000>;
			read-only;
		};
		partition@1 {
			label = "config";
			reg = <0x00020000 0x00060000>;
		};
		partition@2 {
			label = "log";
			reg = <0x00080000 0x00040000>;
		};
		partition@3 {
			label = "kernel";
			reg = <0x000c0000 0x00200000>;
		};
		partition@4 {
			label = "initfs";
			reg = <0x002c0000 0x00200000>;
		};
		partition@5 {
			label = "rootfs";
			reg = <0x004c0000 0x0fb40000>;
		};
	};
};

&mcspi1 {
	/*
	 * For some reason, touchscreen is necessary for screen to work at
	 * all on real hw. It works well without it on emulator.
	 *
	 * Also... order in the device tree actually matters here.
	 */
	tsc2005@0 {
		compatible = "tsc2005";
		spi-max-frequency = <6000000>;
		reg = <0>;
	};

	acx565akm@2 {
		compatible = "sony,acx565akm";
		spi-max-frequency = <6000000>;
		reg = <2>;

		pinctrl-names = "default";
		pinctrl-0 = <&acx565akm_pins>;

		label = "lcd";
		reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */

		port {
			lcd_in: endpoint {
				remote-endpoint = <&sdi_out>;
			};
		};
	};
};

&usb_otg_hs {
	interface-type = <0>;
	usb-phy = <&usb2_phy>;
	phys = <&usb2_phy>;
	phy-names = "usb2-phy";
	mode = <2>;
	power = <50>;
};

&uart1 {
	status = "disabled";
};

&uart2 {
	interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
	pinctrl-names = "default";
	pinctrl-0 = <&uart2_pins>;
};

&uart3 {
	interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
	pinctrl-names = "default";
	pinctrl-0 = <&uart3_pins>;
};

&dss {
	status = "ok";

	pinctrl-names = "default";
	pinctrl-0 = <&dss_sdi_pins>;

	vdds_sdi-supply = <&vaux1>;

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@1 {
			reg = <1>;

			sdi_out: endpoint {
				remote-endpoint = <&lcd_in>;
				datapairs = <2>;
			};
		};
	};
};

&venc {
	status = "ok";

	vdda-supply = <&vdac>;

	port {
		venc_out: endpoint {
			remote-endpoint = <&tv_connector_in>;
			ti,channels = <1>;
		};
	};
};
Commit	Line	Data
a4d4b153 PM	1	/*
a4d4b153 PM	2	* Copyright (C) 2013 Pavel Machek <pavel@ucw.cz>
c3580bc1	3	* Copyright (C) 2013-2014 Aaro Koskinen <aaro.koskinen@iki.fi>
a4d4b153 PM	4	*
	5	* This program is free software; you can redistribute it and/or modify
	6	* it under the terms of the GNU General Public License version 2 (or later) as
	7	* published by the Free Software Foundation.
	8	*/
	9
	10	/dts-v1/;
	11
f2e2c9d9	12	#include "omap34xx-hs.dtsi"
a4d4b153 PM	13
	14	/ {
	15	model = "Nokia N900";
c3580bc1	16	compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3";
a4d4b153 PM	17
	18	cpus {
	19	cpu@0 {
	20	cpu0-supply = <&vcc>;
	21	};
	22	};
	23
c1be2032 TL	24	leds {
	25	compatible = "gpio-leds";
	26	heartbeat {
	27	label = "debug::sleep";
	28	gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio162 */
	29	linux,default-trigger = "default-on";
	30	pinctrl-names = "default";
	31	pinctrl-0 = <&debug_leds>;
	32	};
	33	};
	34
a4d4b153 PM	35	memory {
	36	device_type = "memory";
	37	reg = <0x80000000 0x10000000>; /* 256 MB */
	38	};
	39
3931c839 SR	40	gpio_keys {
	41	compatible = "gpio-keys";
	42
	43	camera_lens_cover {
	44	label = "Camera Lens Cover";
	45	gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
	46	linux,input-type = <5>; /* EV_SW */
	47	linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */
	48	gpio-key,wakeup;
	49	};
	50
	51	camera_focus {
	52	label = "Camera Focus";
	53	gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
	54	linux,code = <0x210>; /* KEY_CAMERA_FOCUS */
	55	gpio-key,wakeup;
	56	};
	57
	58	camera_capture {
	59	label = "Camera Capture";
	60	gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
	61	linux,code = <0xd4>; /* KEY_CAMERA */
	62	gpio-key,wakeup;
	63	};
	64
	65	lock_button {
	66	label = "Lock Button";
	67	gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
	68	linux,code = <0x98>; /* KEY_SCREENLOCK */
	69	gpio-key,wakeup;
	70	};
	71
	72	keypad_slide {
	73	label = "Keypad Slide";
	74	gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
	75	linux,input-type = <5>; /* EV_SW */
	76	linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */
	77	gpio-key,wakeup;
	78	};
	79
	80	proximity_sensor {
	81	label = "Proximity Sensor";
	82	gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
	83	linux,input-type = <5>; /* EV_SW */
	84	linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */
	85	};
	86	};
	87
e17337a2 SR	88	isp1704: isp1704 {
	89	compatible = "nxp,isp1704";
	90	nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
	91	usb-phy = <&usb2_phy>;
	92	};
1133420f TV	93
	94	tv: connector {
	95	compatible = "composite-connector";
	96	label = "tv";
	97
	98	port {
	99	tv_connector_in: endpoint {
	100	remote-endpoint = <&venc_out>;
	101	};
	102	};
	103	};
a4d4b153 PM	104	};
a4d4b153 PM	105
ac888a88 SR	106	&omap3_pmx_core {
	107	pinctrl-names = "default";
	108
7a89eecf SR	109	uart2_pins: pinmux_uart2_pins {
	110	pinctrl-single,pins = <
	111	0x14a (PIN_INPUT \| MUX_MODE0) /* uart2_rx */
	112	0x148 (PIN_OUTPUT \| MUX_MODE0) /* uart2_tx */
	113	>;
	114	};
	115
	116	uart3_pins: pinmux_uart3_pins {
	117	pinctrl-single,pins = <
	118	0x16e (PIN_INPUT \| MUX_MODE0) /* uart3_rx */
	119	0x170 (PIN_OUTPUT \| MUX_MODE0) /* uart3_tx */
	120	>;
	121	};
	122
ac888a88 SR	123	i2c1_pins: pinmux_i2c1_pins {
	124	pinctrl-single,pins = <
	125	0x18a (PIN_INPUT_PULLUP \| MUX_MODE0) /* i2c1_scl */
	126	0x18c (PIN_INPUT_PULLUP \| MUX_MODE0) /* i2c1_sda */
	127	>;
	128	};
	129
	130	i2c2_pins: pinmux_i2c2_pins {
	131	pinctrl-single,pins = <
	132	0x18e (PIN_INPUT_PULLUP \| MUX_MODE0) /* i2c2_scl */
	133	0x190 (PIN_INPUT_PULLUP \| MUX_MODE0) /* i2c2_sda */
	134	>;
	135	};
	136
	137	i2c3_pins: pinmux_i2c3_pins {
	138	pinctrl-single,pins = <
	139	0x192 (PIN_INPUT_PULLUP \| MUX_MODE0) /* i2c3_scl */
	140	0x194 (PIN_INPUT_PULLUP \| MUX_MODE0) /* i2c3_sda */
	141	>;
	142	};
f1751cff	143
c1be2032 TL	144	debug_leds: pinmux_debug_led_pins {
	145	pinctrl-single,pins = <
	146	OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT \| MUX_MODE4) /* mcbsp1_clkx.gpio_162 */
	147	>;
	148	};
	149
f1751cff SR	150	mmc1_pins: pinmux_mmc1_pins {
	151	pinctrl-single,pins = <
	152	0x114 (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc1_clk */
	153	0x116 (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc1_cmd */
	154	0x118 (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc1_dat0 */
	155	0x11a (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc1_dat1 */
	156	0x11c (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc1_dat2 */
	157	0x11e (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc1_dat3 */
	158	>;
	159	};
d1e6f516	160
edd5eb4e TL	161	mmc2_pins: pinmux_mmc2_pins {
	162	pinctrl-single,pins = <
	163	0x128 (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc2_clk */
	164	0x12a (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc2_cmd */
	165	0x12c (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc2_dat0 */
	166	0x12e (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc2_dat1 */
	167	0x130 (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc2_dat2 */
	168	0x132 (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc2_dat3 */
	169	0x134 (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc2_dat4 */
	170	0x136 (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc2_dat5 */
	171	0x138 (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc2_dat6 */
	172	0x13a (PIN_INPUT_PULLUP \| MUX_MODE0) /* sdmmc2_dat7 */
	173	>;
	174	};
	175
1133420f	176	acx565akm_pins: pinmux_acx565akm_pins {
d1e6f516 SR	177	pinctrl-single,pins = <
	178	0x0d4 (PIN_OUTPUT \| MUX_MODE4) /* RX51_LCD_RESET_GPIO */
	179	>;
	180	};
1133420f TV	181
	182	dss_sdi_pins: pinmux_dss_sdi_pins {
	183	pinctrl-single,pins = <
	184	0x0c0 (PIN_OUTPUT \| MUX_MODE1) /* dss_data10.sdi_dat1n */
	185	0x0c2 (PIN_OUTPUT \| MUX_MODE1) /* dss_data11.sdi_dat1p */
	186	0x0c4 (PIN_OUTPUT \| MUX_MODE1) /* dss_data12.sdi_dat2n */
	187	0x0c6 (PIN_OUTPUT \| MUX_MODE1) /* dss_data13.sdi_dat2p */
	188
	189	0x0d8 (PIN_OUTPUT \| MUX_MODE1) /* dss_data22.sdi_clkp */
	190	0x0da (PIN_OUTPUT \| MUX_MODE1) /* dss_data23.sdi_clkn */
	191	>;
	192	};
ac888a88 SR	193	};
ac888a88 SR	194
a4d4b153	195	&i2c1 {
ac888a88 SR	196	pinctrl-names = "default";
	197	pinctrl-0 = <&i2c1_pins>;
	198
a4d4b153 PM	199	clock-frequency = <2200000>;
	200
	201	twl: twl@48 {
	202	reg = <0x48>;
	203	interrupts = <7>; /* SYS_NIRQ cascaded to intc */
	204	interrupt-parent = <&intc>;
	205	};
	206	};
	207
	208	#include "twl4030.dtsi"
ac888a88	209	#include "twl4030_omap3.dtsi"
a4d4b153	210
9cdbbadd SR	211	&vaux1 {
	212	regulator-name = "V28";
	213	regulator-min-microvolt = <2800000>;
	214	regulator-max-microvolt = <2800000>;
	215	regulator-always-on; /* due battery cover sensor */
	216	};
	217
	218	&vaux2 {
	219	regulator-name = "VCSI";
	220	regulator-min-microvolt = <1800000>;
	221	regulator-max-microvolt = <1800000>;
	222	};
	223
	224	&vaux3 {
	225	regulator-name = "VMMC2_30";
	226	regulator-min-microvolt = <2800000>;
	227	regulator-max-microvolt = <3000000>;
	228	};
	229
	230	&vaux4 {
	231	regulator-name = "VCAM_ANA_28";
	232	regulator-min-microvolt = <2800000>;
	233	regulator-max-microvolt = <2800000>;
	234	};
	235
	236	&vmmc1 {
	237	regulator-name = "VMMC1";
	238	regulator-min-microvolt = <1850000>;
	239	regulator-max-microvolt = <3150000>;
	240	};
	241
	242	&vmmc2 {
	243	regulator-name = "V28_A";
	244	regulator-min-microvolt = <2800000>;
	245	regulator-max-microvolt = <3000000>;
	246	regulator-always-on; /* due VIO leak to AIC34 VDDs */
	247	};
	248
	249	&vpll1 {
	250	regulator-name = "VPLL";
	251	regulator-min-microvolt = <1800000>;
	252	regulator-max-microvolt = <1800000>;
	253	regulator-always-on;
	254	};
	255
	256	&vpll2 {
	257	regulator-name = "VSDI_CSI";
	258	regulator-min-microvolt = <1800000>;
	259	regulator-max-microvolt = <1800000>;
	260	regulator-always-on;
	261	};
	262
	263	&vsim {
	264	regulator-name = "VMMC2_IO_18";
	265	regulator-min-microvolt = <1800000>;
	266	regulator-max-microvolt = <1800000>;
	267	};
	268
	269	&vio {
	270	regulator-name = "VIO";
	271	regulator-min-microvolt = <1800000>;
	272	regulator-max-microvolt = <1800000>;
	273
	274	};
275
276	&vintana1 {
277	regulator-name = "VINTANA1";
278	/* fixed to 1500000 */
279	regulator-always-on;
280	};
281
282	&vintana2 {
283	regulator-name = "VINTANA2";
284	regulator-min-microvolt = <2750000>;
285	regulator-max-microvolt = <2750000>;
286	regulator-always-on;
287	};
288
289	&vintdig {
290	regulator-name = "VINTDIG";
291	/* fixed to 1500000 */
292	regulator-always-on;
293	};
294
06ba7a61 SR	295	&twl {
	296	twl_audio: audio {
	297	compatible = "ti,twl4030-audio";
	298	ti,enable-vibra = <1>;
	299	};
	300	};
	301
85c215f3 SR	302	&twl_keypad {
	303	linux,keymap = < 0x00000010 /* KEY_Q */
	304	0x00010018 /* KEY_O */
	305	0x00020019 /* KEY_P */
	306	0x00030033 /* KEY_COMMA */
	307	0x0004000e /* KEY_BACKSPACE */
	308	0x0006001e /* KEY_A */
	309	0x0007001f /* KEY_S */
	310
	311	0x01000011 /* KEY_W */
	312	0x01010020 /* KEY_D */
	313	0x01020021 /* KEY_F */
	314	0x01030022 /* KEY_G */
	315	0x01040023 /* KEY_H */
	316	0x01050024 /* KEY_J */
	317	0x01060025 /* KEY_K */
	318	0x01070026 /* KEY_L */
	319
	320	0x02000012 /* KEY_E */
	321	0x02010034 /* KEY_DOT */
	322	0x02020067 /* KEY_UP */
	323	0x0203001c /* KEY_ENTER */
	324	0x0205002c /* KEY_Z */
	325	0x0206002d /* KEY_X */
	326	0x0207002e /* KEY_C */
	327	0x02080043 /* KEY_F9 */
	328
	329	0x03000013 /* KEY_R */
	330	0x0301002f /* KEY_V */
	331	0x03020030 /* KEY_B */
	332	0x03030031 /* KEY_N */
	333	0x03040032 /* KEY_M */
	334	0x03050039 /* KEY_SPACE */
	335	0x03060039 /* KEY_SPACE */
	336	0x03070069 /* KEY_LEFT */
	337
	338	0x04000014 /* KEY_T */
	339	0x0401006c /* KEY_DOWN */
	340	0x0402006a /* KEY_RIGHT */
	341	0x0404001d /* KEY_LEFTCTRL */
	342	0x04050064 /* KEY_RIGHTALT */
	343	0x0406002a /* KEY_LEFTSHIFT */
	344	0x04080044 /* KEY_F10 */
	345
	346	0x05000015 /* KEY_Y */
	347	0x05080057 /* KEY_F11 */
	348
	349	0x06000016 /* KEY_U */
	350
	351	0x07000017 /* KEY_I */
	352	0x07010041 /* KEY_F7 */
	353	0x07020042 /* KEY_F8 */
	354	>;
	355	};
	356
a4d4b153 PM	357	&twl_gpio {
	358	ti,pullups = <0x0>;
	359	ti,pulldowns = <0x03ff3f>; /* BIT(0..5) \| BIT(8..17) */
	360	};
	361
	362	&i2c2 {
ac888a88 SR	363	pinctrl-names = "default";
	364	pinctrl-0 = <&i2c2_pins>;
	365
48fc9864	366	clock-frequency = <100000>;
b2b9b258	367
14e3e295 SR	368	tlv320aic3x: tlv320aic3x@18 {
	369	compatible = "ti,tlv320aic3x";
	370	reg = <0x18>;
	371	gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
	372	ai3x-gpio-func = <
	373	0 /* AIC3X_GPIO1_FUNC_DISABLED */
	374	5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
	375	>;
	376
	377	AVDD-supply = <&vmmc2>;
	378	DRVDD-supply = <&vmmc2>;
	379	IOVDD-supply = <&vio>;
	380	DVDD-supply = <&vio>;
	381	};
	382
	383	tlv320aic3x_aux: tlv320aic3x@19 {
	384	compatible = "ti,tlv320aic3x";
	385	reg = <0x19>;
	386	gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
	387
	388	AVDD-supply = <&vmmc2>;
	389	DRVDD-supply = <&vmmc2>;
	390	IOVDD-supply = <&vio>;
	391	DVDD-supply = <&vio>;
	392	};
	393
12f2f873 SR	394	tsl2563: tsl2563@29 {
	395	compatible = "amstaos,tsl2563";
	396	reg = <0x29>;
	397
	398	amstaos,cover-comp-gain = <16>;
	399	};
	400
a0bf1f3e SR	401	lp5523: lp5523@32 {
	402	compatible = "national,lp5523";
	403	reg = <0x32>;
	404	clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
	405	enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
	406
	407	chan0 {
	408	chan-name = "lp5523:kb1";
	409	led-cur = /bits/ 8 <50>;
	410	max-cur = /bits/ 8 <100>;
	411	};
	412
	413	chan1 {
	414	chan-name = "lp5523:kb2";
	415	led-cur = /bits/ 8 <50>;
	416	max-cur = /bits/ 8 <100>;
	417	};
	418
	419	chan2 {
	420	chan-name = "lp5523:kb3";
	421	led-cur = /bits/ 8 <50>;
	422	max-cur = /bits/ 8 <100>;
	423	};
	424
	425	chan3 {
	426	chan-name = "lp5523:kb4";
	427	led-cur = /bits/ 8 <50>;
	428	max-cur = /bits/ 8 <100>;
	429	};
	430
	431	chan4 {
	432	chan-name = "lp5523:b";
	433	led-cur = /bits/ 8 <50>;
	434	max-cur = /bits/ 8 <100>;
	435	};
	436
	437	chan5 {
	438	chan-name = "lp5523:g";
	439	led-cur = /bits/ 8 <50>;
	440	max-cur = /bits/ 8 <100>;
	441	};
	442
	443	chan6 {
	444	chan-name = "lp5523:r";
	445	led-cur = /bits/ 8 <50>;
	446	max-cur = /bits/ 8 <100>;
	447	};
	448
	449	chan7 {
	450	chan-name = "lp5523:kb5";
	451	led-cur = /bits/ 8 <50>;
	452	max-cur = /bits/ 8 <100>;
	453	};
	454
	455	chan8 {
	456	chan-name = "lp5523:kb6";
	457	led-cur = /bits/ 8 <50>;
	458	max-cur = /bits/ 8 <100>;
	459	};
	460	};
	461
b2b9b258 SR	462	bq27200: bq27200@55 {
	463	compatible = "ti,bq27200";
	464	reg = <0x55>;
	465	};
9e2367c8 SR	466
	467	tpa6130a2: tpa6130a2@60 {
	468	compatible = "ti,tpa6130a2";
	469	reg = <0x60>;
	470
	471	Vdd-supply = <&vmmc2>;
	472
	473	power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */
	474	};
334a09c8 SR	475
	476	bq24150a: bq24150a@6b {
	477	compatible = "ti,bq24150a";
	478	reg = <0x6b>;
	479
	480	ti,current-limit = <100>;
	481	ti,weak-battery-voltage = <3400>;
	482	ti,battery-regulation-voltage = <4200>;
	483	ti,charge-current = <650>;
	484	ti,termination-current = <100>;
	485	ti,resistor-sense = <68>;
	486
	487	ti,usb-charger-detection = <&isp1704>;
	488	};
a4d4b153 PM	489	};
	490
	491	&i2c3 {
ac888a88 SR	492	pinctrl-names = "default";
	493	pinctrl-0 = <&i2c3_pins>;
	494
48fc9864	495	clock-frequency = <400000>;
a4d4b153 PM	496	};
	497
	498	&mmc1 {
f1751cff SR	499	pinctrl-names = "default";
	500	pinctrl-0 = <&mmc1_pins>;
	501	vmmc-supply = <&vmmc1>;
	502	bus-width = <4>;
	503	cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
a4d4b153 PM	504	};
a4d4b153 PM	505
edd5eb4e	506	/* most boards use vaux3, only some old versions use vmmc2 instead */
a4d4b153	507	&mmc2 {
edd5eb4e TL	508	pinctrl-names = "default";
	509	pinctrl-0 = <&mmc2_pins>;
	510	vmmc-supply = <&vaux3>;
	511	vmmc_aux-supply = <&vsim>;
	512	bus-width = <8>;
	513	non-removable;
a4d4b153 PM	514	};
	515
	516	&mmc3 {
	517	status = "disabled";
	518	};
	519
8699d2dd SR	520	&gpmc {
	521	ranges = <0 0 0x04000000 0x10000000>; /* 256MB */
	522
	523	/* gpio-irq for dma: 65 */
	524
	525	onenand@0,0 {
	526	#address-cells = <1>;
	527	#size-cells = <1>;
	528	reg = <0 0 0x10000000>;
	529
	530	gpmc,sync-read;
	531	gpmc,sync-write;
	532	gpmc,burst-length = <16>;
	533	gpmc,burst-read;
	534	gpmc,burst-wrap;
	535	gpmc,burst-write;
	536	gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
	537	gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
	538	gpmc,cs-on-ns = <0>;
	539	gpmc,cs-rd-off-ns = <87>;
	540	gpmc,cs-wr-off-ns = <87>;
	541	gpmc,adv-on-ns = <0>;
	542	gpmc,adv-rd-off-ns = <10>;
	543	gpmc,adv-wr-off-ns = <10>;
	544	gpmc,oe-on-ns = <15>;
	545	gpmc,oe-off-ns = <87>;
	546	gpmc,we-on-ns = <0>;
	547	gpmc,we-off-ns = <87>;
	548	gpmc,rd-cycle-ns = <112>;
	549	gpmc,wr-cycle-ns = <112>;
	550	gpmc,access-ns = <81>;
	551	gpmc,page-burst-access-ns = <15>;
	552	gpmc,bus-turnaround-ns = <0>;
	553	gpmc,cycle2cycle-delay-ns = <0>;
	554	gpmc,wait-monitoring-ns = <0>;
	555	gpmc,clk-activation-ns = <5>;
	556	gpmc,wr-data-mux-bus-ns = <30>;
	557	gpmc,wr-access-ns = <81>;
	558	gpmc,sync-clk-ps = <15000>;
	559
	560	/*
	561	* MTD partition table corresponding to Nokia's
	562	* Maemo 5 (Fremantle) release.
	563	*/
	564	partition@0 {
	565	label = "bootloader";
	566	reg = <0x00000000 0x00020000>;
	567	read-only;
	568	};
	569	partition@1 {
	570	label = "config";
	571	reg = <0x00020000 0x00060000>;
	572	};
	573	partition@2 {
	574	label = "log";
	575	reg = <0x00080000 0x00040000>;
	576	};
	577	partition@3 {
	578	label = "kernel";
	579	reg = <0x000c0000 0x00200000>;
	580	};
	581	partition@4 {
	582	label = "initfs";
	583	reg = <0x002c0000 0x00200000>;
584	};
585	partition@5 {
586	label = "rootfs";
587	reg = <0x004c0000 0x0fb40000>;
588	};
589	};
590	};
591
a4d4b153 PM	592	&mcspi1 {
	593	/*
	594	* For some reason, touchscreen is necessary for screen to work at
	595	* all on real hw. It works well without it on emulator.
	596	*
	597	* Also... order in the device tree actually matters here.
	598	*/
	599	tsc2005@0 {
	600	compatible = "tsc2005";
	601	spi-max-frequency = <6000000>;
	602	reg = <0>;
	603	};
1133420f TV	604
	605	acx565akm@2 {
	606	compatible = "sony,acx565akm";
a4d4b153 PM	607	spi-max-frequency = <6000000>;
a4d4b153 PM	608	reg = <2>;
d1e6f516 SR	609
d1e6f516 SR	610	pinctrl-names = "default";
1133420f TV	611	pinctrl-0 = <&acx565akm_pins>;
	612
	613	label = "lcd";
	614	reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
	615
	616	port {
	617	lcd_in: endpoint {
	618	remote-endpoint = <&sdi_out>;
	619	};
	620	};
a4d4b153 PM	621	};
	622	};
	623
	624	&usb_otg_hs {
	625	interface-type = <0>;
	626	usb-phy = <&usb2_phy>;
d2afcf09 RQ	627	phys = <&usb2_phy>;
d2afcf09 RQ	628	phy-names = "usb2-phy";
a4d4b153 PM	629	mode = <2>;
	630	power = <50>;
	631	};
7a89eecf SR	632
	633	&uart1 {
	634	status = "disabled";
	635	};
	636
	637	&uart2 {
31f0820a	638	interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
7a89eecf SR	639	pinctrl-names = "default";
	640	pinctrl-0 = <&uart2_pins>;
	641	};
	642
	643	&uart3 {
31f0820a	644	interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
7a89eecf SR	645	pinctrl-names = "default";
	646	pinctrl-0 = <&uart3_pins>;
	647	};
1133420f TV	648
	649	&dss {
	650	status = "ok";
	651
	652	pinctrl-names = "default";
	653	pinctrl-0 = <&dss_sdi_pins>;
	654
	655	vdds_sdi-supply = <&vaux1>;
	656
	657	ports {
	658	#address-cells = <1>;
	659	#size-cells = <0>;
	660
	661	port@1 {
	662	reg = <1>;
	663
	664	sdi_out: endpoint {
	665	remote-endpoint = <&lcd_in>;
	666	datapairs = <2>;
	667	};
	668	};
	669	};
	670	};
	671
	672	&venc {
	673	status = "ok";
	674
	675	vdda-supply = <&vdac>;
	676
	677	port {
	678	venc_out: endpoint {
	679	remote-endpoint = <&tv_connector_in>;
	680	ti,channels = <1>;
	681	};
	682	};
	683	};