projects / deliverable / linux.git / blame
? search:
summary | shortlog | log | commit | commitdiff | tree
blob | blame (incremental) | history | HEAD
ARM: dts: sbc-t54: fix mux mode comment style
[deliverable/linux.git] / arch / arm / boot / dts / omap5-cm-t54.dts
CommitLineData
9f642b5c
DL		 1/*
2 * Support for CompuLab CM-T54
3 */
4/dts-v1/;
5
6#include "omap5.dtsi"
7#include <dt-bindings/interrupt-controller/irq.h>
8#include <dt-bindings/interrupt-controller/arm-gic.h>
9
10/ {
11 model = "CompuLab CM-T54";
12 compatible = "compulab,omap5-cm-t54", "ti,omap5";
13
14 memory {
15 device_type = "memory";
16 reg = <0x80000000 0x7F000000>; /* 2048 MB */
17 };
18
19 vmmcsd_fixed: fixed-regulator-mmcsd {
20 compatible = "regulator-fixed";
21 regulator-name = "vmmcsd_fixed";
22 regulator-min-microvolt = <3300000>;
23 regulator-max-microvolt = <3300000>;
24 };
25
4a996d18
DL		 26 vwlan_pdn_fixed: fixed-regulator-vwlan-pdn {
27 compatible = "regulator-fixed";
28 regulator-name = "vwlan_pdn_fixed";
29 regulator-min-microvolt = <3300000>;
30 regulator-max-microvolt = <3300000>;
31 vin-supply = <&ldo2_reg>;
32 gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>; /* gpio4_109 */
33 startup-delay-us = <1000>;
34 enable-active-high;
35 };
36
37 vwlan_fixed: fixed-regulator-vwlan {
38 compatible = "regulator-fixed";
39 regulator-name = "vwlan_fixed";
40 regulator-min-microvolt = <3300000>;
41 regulator-max-microvolt = <3300000>;
42 vin-supply = <&vwlan_pdn_fixed>;
43 gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* gpio4_110 */
44 startup-delay-us = <1000>;
45 enable-active-high;
46 };
47
9f642b5c
DL		 48 /* HS USB Host PHY on PORT 2 */
49 hsusb2_phy: hsusb2_phy {
50 compatible = "usb-nop-xceiv";
51 reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
52 };
53
54 /* HS USB Host PHY on PORT 3 */
55 hsusb3_phy: hsusb3_phy {
56 compatible = "usb-nop-xceiv";
57 reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */
58 };
59
60 leds {
61 compatible = "gpio-leds";
62 led@1 {
63 label = "Heartbeat";
64 gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */
65 linux,default-trigger = "heartbeat";
66 default-state = "off";
67 };
68 };
69};
70
71&omap5_pmx_core {
72 pinctrl-names = "default";
73 pinctrl-0 = <
74 &led_gpio_pins
75 &usbhost_pins
76 >;
77
78 led_gpio_pins: pinmux_led_gpio_pins {
79 pinctrl-single,pins = <
4b466297 80 OMAP5_IOPAD(0x00b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */
9f642b5c
DL		 81 >;
82 };
83
84 i2c1_pins: pinmux_i2c1_pins {
85 pinctrl-single,pins = <
4b466297
JE		 86 OMAP5_IOPAD(0x01f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */
87 OMAP5_IOPAD(0x01f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */
9f642b5c
DL		 88 >;
89 };
90
91 mmc1_pins: pinmux_mmc1_pins {
92 pinctrl-single,pins = <
4b466297
JE		 93 OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
94 OMAP5_IOPAD(0x01e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */
95 OMAP5_IOPAD(0x01e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */
96 OMAP5_IOPAD(0x01e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */
97 OMAP5_IOPAD(0x01ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */
98 OMAP5_IOPAD(0x01ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */
9f642b5c
DL		 99 >;
100 };
101
102 mmc2_pins: pinmux_mmc2_pins {
103 pinctrl-single,pins = <
4b466297
JE		 104 OMAP5_IOPAD(0x0040, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */
105 OMAP5_IOPAD(0x0042, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */
106 OMAP5_IOPAD(0x0044, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */
107 OMAP5_IOPAD(0x0046, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */
108 OMAP5_IOPAD(0x0048, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */
109 OMAP5_IOPAD(0x004a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */
110 OMAP5_IOPAD(0x004c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */
111 OMAP5_IOPAD(0x004e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */
112 OMAP5_IOPAD(0x0050, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */
113 OMAP5_IOPAD(0x0052, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */
9f642b5c
DL		 114 >;
115 };
116
4a996d18
DL		 117 mmc3_pins: pinmux_mmc3_pins {
118 pinctrl-single,pins = <
4b466297
JE		 119 OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
120 OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
121 OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
122 OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
123 OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
124 OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
4a996d18
DL		 125 >;
126 };
127
128 wlan_gpios_pins: pinmux_wlan_gpios_pins {
129 pinctrl-single,pins = <
4b466297
JE		 130 OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_109 */
131 OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_110 */
4a996d18
DL		 132 >;
133 };
134
9f642b5c
DL		 135 usbhost_pins: pinmux_usbhost_pins {
136 pinctrl-single,pins = <
4b466297
JE		 137 OMAP5_IOPAD(0x00c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
138 OMAP5_IOPAD(0x00c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
9f642b5c 139
4b466297
JE		 140 OMAP5_IOPAD(0x01dc, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
141 OMAP5_IOPAD(0x01de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
9f642b5c 142
4b466297
JE		 143 OMAP5_IOPAD(0x00a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */
144 OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */
9f642b5c
DL		 145 >;
146 };
147};
148
149&mmc1 {
150 pinctrl-names = "default";
151 pinctrl-0 = <&mmc1_pins>;
152 vmmc-supply = <&ldo9_reg>;
153 bus-width = <4>;
154};
155
156&mmc2 {
157 pinctrl-names = "default";
158 pinctrl-0 = <&mmc2_pins>;
159 vmmc-supply = <&vmmcsd_fixed>;
160 bus-width = <8>;
161 ti,non-removable;
162};
163
4a996d18
DL		 164&mmc3 {
165 pinctrl-names = "default";
166 pinctrl-0 = <
167 &mmc3_pins
168 &wlan_gpios_pins
169 >;
170 vmmc-supply = <&vwlan_fixed>;
171 bus-width = <4>;
172 ti,non-removable;
173};
174
9f642b5c
DL		 175&mmc4 {
176 status = "disabled";
177};
178
179&mmc5 {
180 status = "disabled";
181};
182
183&i2c1 {
184 pinctrl-names = "default";
185 pinctrl-0 = <&i2c1_pins>;
186
187 clock-frequency = <400000>;
188
189 at24@50 {
190 compatible = "at24,24c02";
191 pagesize = <16>;
192 reg = <0x50>;
193 };
194
195 palmas: palmas@48 {
196 compatible = "ti,palmas";
197 interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
198 interrupt-parent = <&gic>;
199 reg = <0x48>;
200 interrupt-controller;
201 #interrupt-cells = <2>;
202 ti,system-power-controller;
203
204 extcon_usb3: palmas_usb {
205 compatible = "ti,palmas-usb-vid";
206 ti,enable-vbus-detection;
207 ti,enable-id-detection;
208 ti,wakeup;
209 };
210
211 rtc {
212 compatible = "ti,palmas-rtc";
213 interrupt-parent = <&palmas>;
214 interrupts = <8 IRQ_TYPE_NONE>;
215 };
216
217 palmas_pmic {
218 compatible = "ti,palmas-pmic";
219 interrupt-parent = <&palmas>;
220 interrupts = <14 IRQ_TYPE_NONE>;
221 interrupt-name = "short-irq";
222
223 ti,ldo6-vibrator;
224
225 regulators {
226 smps123_reg: smps123 {
227 /* VDD_OPP_MPU */
228 regulator-name = "smps123";
229 regulator-min-microvolt = < 600000>;
230 regulator-max-microvolt = <1500000>;
231 regulator-always-on;
232 regulator-boot-on;
233 };
234
235 smps45_reg: smps45 {
236 /* VDD_OPP_MM */
237 regulator-name = "smps45";
238 regulator-min-microvolt = < 600000>;
239 regulator-max-microvolt = <1310000>;
240 regulator-always-on;
241 regulator-boot-on;
242 };
243
244 smps6_reg: smps6 {
245 /* VDD_DDR3 - over VDD_SMPS6 */
246 regulator-name = "smps6";
247 regulator-min-microvolt = <1500000>;
248 regulator-max-microvolt = <1500000>;
249 regulator-always-on;
250 regulator-boot-on;
251 };
252
253 smps7_reg: smps7 {
254 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
255 regulator-name = "smps7";
256 regulator-min-microvolt = <1800000>;
257 regulator-max-microvolt = <1800000>;
258 regulator-always-on;
259 regulator-boot-on;
260 };
261
262 smps8_reg: smps8 {
263 /* VDD_OPP_CORE */
264 regulator-name = "smps8";
265 regulator-min-microvolt = < 600000>;
266 regulator-max-microvolt = <1310000>;
267 regulator-always-on;
268 regulator-boot-on;
269 };
270
271 smps9_reg: smps9 {
272 /* VDDA_2v1_AUD over VDD_2v1 */
273 regulator-name = "smps9";
274 regulator-min-microvolt = <3300000>;
275 regulator-max-microvolt = <3300000>;
276 ti,smps-range = <0x80>;
277 regulator-always-on;
278 regulator-boot-on;
279 };
280
281 smps10_out2_reg: smps10_out2 {
282 /* VBUS_5V_OTG */
283 regulator-name = "smps10_out2";
284 regulator-min-microvolt = <5000000>;
285 regulator-max-microvolt = <5000000>;
286 regulator-always-on;
287 regulator-boot-on;
288 };
289
290 smps10_out1_reg: smps10_out1 {
291 /* VBUS_5V_OTG */
292 regulator-name = "smps10_out1";
293 regulator-min-microvolt = <5000000>;
294 regulator-max-microvolt = <5000000>;
295 };
296
297 ldo1_reg: ldo1 {
298 /* VDDAPHY_CAM: vdda_csiport */
299 regulator-name = "ldo1";
300 regulator-min-microvolt = <1500000>;
301 regulator-max-microvolt = <1800000>;
302 };
303
304 ldo2_reg: ldo2 {
305 /* VDD_3V3_WLAN */
306 regulator-name = "ldo2";
307 regulator-min-microvolt = <3300000>;
308 regulator-max-microvolt = <3300000>;
4a996d18 309 startup-delay-us = <1000>;
9f642b5c
DL		 310 };
311
312 ldo3_reg: ldo3 {
313 /* VCC_1V5_AUD */
314 regulator-name = "ldo3";
315 regulator-min-microvolt = <1500000>;
316 regulator-max-microvolt = <1500000>;
317 regulator-always-on;
318 regulator-boot-on;
319 };
320
321 ldo4_reg: ldo4 {
322 /* VDDAPHY_DISP: vdda_dsiport/hdmi */
323 regulator-name = "ldo4";
324 regulator-min-microvolt = <1500000>;
325 regulator-max-microvolt = <1800000>;
326 };
327
328 ldo5_reg: ldo5 {
329 /* VDDA_1V8_PHY: usb/sata/hdmi.. */
330 regulator-name = "ldo5";
331 regulator-min-microvolt = <1800000>;
332 regulator-max-microvolt = <1800000>;
333 regulator-always-on;
334 regulator-boot-on;
335 };
336
337 ldo6_reg: ldo6 {
338 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
339 regulator-name = "ldo6";
340 regulator-min-microvolt = <1200000>;
341 regulator-max-microvolt = <1200000>;
342 regulator-always-on;
343 regulator-boot-on;
344 };
345
346 ldo7_reg: ldo7 {
347 /* VDD_VPP: vpp1 */
348 regulator-name = "ldo7";
349 regulator-min-microvolt = <2000000>;
350 regulator-max-microvolt = <2000000>;
351 /* Only for efuse reprograming! */
352 status = "disabled";
353 };
354
355 ldo8_reg: ldo8 {
356 /* VDD_3v0: Does not go anywhere */
357 regulator-name = "ldo8";
358 regulator-min-microvolt = <3000000>;
359 regulator-max-microvolt = <3000000>;
360 regulator-boot-on;
361 /* Unused */
362 status = "disabled";
363 };
364
365 ldo9_reg: ldo9 {
366 /* VCC_DV_SDIO: vdds_sdcard */
367 regulator-name = "ldo9";
368 regulator-min-microvolt = <1800000>;
369 regulator-max-microvolt = <3000000>;
370 regulator-boot-on;
371 };
372
373 ldoln_reg: ldoln {
374 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
375 regulator-name = "ldoln";
376 regulator-min-microvolt = <1800000>;
377 regulator-max-microvolt = <1800000>;
378 regulator-always-on;
379 regulator-boot-on;
380 };
381
382 ldousb_reg: ldousb {
383 /* VDDA_3V_USB: VDDA_USBHS33 */
384 regulator-name = "ldousb";
385 regulator-min-microvolt = <3250000>;
386 regulator-max-microvolt = <3250000>;
387 regulator-always-on;
388 regulator-boot-on;
389 };
390
391 regen3_reg: regen3 {
392 /* REGEN3 controls LDO9 supply to card */
393 regulator-name = "regen3";
394 regulator-always-on;
395 regulator-boot-on;
396 };
397 };
398 };
399 };
400};
401
402&usbhshost {
403 port2-mode = "ehci-hsic";
404 port3-mode = "ehci-hsic";
405};
406
407&usbhsehci {
408 phys = <0 &hsusb2_phy &hsusb3_phy>;
409};
410
411&cpu0 {
412 cpu0-supply = <&smps123_reg>;
413};
Linux kernel - Deliverables
This page took 0.063627 seconds and 5 git commands to generate.