projects / deliverable / linux.git / blame
| Commit | Line | Data |
|---|---|---|
| 9c19cfa9 LW |
1 | /* |
| 2 | * Copyright 2012 ST-Ericsson AB | |
| 3 | * | |
| 4 | * The code contained herein is licensed under the GNU General Public | |
| 5 | * License. You may obtain a copy of the GNU General Public License | |
| 6 | * Version 2 or later at the following locations: | |
| 7 | * | |
| 8 | * http://www.opensource.org/licenses/gpl-license.html | |
| 9 | * http://www.gnu.org/copyleft/gpl.html | |
| 10 | * | |
| 11 | * Device Tree for the TVK1281618 UIB | |
| 12 | */ | |
| 13 | ||
| 14 | #include <dt-bindings/interrupt-controller/irq.h> | |
| 15 | ||
| 16 | / { | |
| 1a780d45 LW |
17 | gpio_keys { |
| 18 | compatible = "gpio-keys"; | |
| 19 | #address-cells = <1>; | |
| 20 | #size-cells = <0>; | |
| 21 | vdd-supply = <&ab8500_ldo_aux1_reg>; | |
| 22 | pinctrl-names = "default"; | |
| 23 | pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>; | |
| 24 | ||
| 25 | button@139 { | |
| 26 | /* Proximity sensor */ | |
| 1b1e8e02 | 27 | gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>; |
| 1a780d45 LW |
28 | linux,code = <11>; /* SW_FRONT_PROXIMITY */ |
| 29 | label = "SFH7741 Proximity Sensor"; | |
| 30 | }; | |
| 31 | button@145 { | |
| 32 | /* Hall sensor */ | |
| 1b1e8e02 | 33 | gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>; |
| 1a780d45 LW |
34 | linux,code = <0>; /* SW_LID */ |
| 35 | label = "HED54XXU11 Hall Effect Sensor"; | |
| 36 | }; | |
| 37 | }; | |
| 38 | ||
| 9c19cfa9 | 39 | soc { |
| 84919b96 | 40 | i2c@80004000 { |
| 7e0a51a0 LW |
41 | tc35893@44 { |
| 42 | compatible = "toshiba,tc35893"; | |
| 84919b96 LW |
43 | reg = <0x44>; |
| 44 | interrupt-parent = <&gpio6>; | |
| 45 | interrupts = <26 IRQ_TYPE_EDGE_RISING>; | |
| a45cb698 LW |
46 | pinctrl-names = "default"; |
| 47 | pinctrl-0 = <&tc35893_tvk_mode>; | |
| 84919b96 LW |
48 | |
| 49 | interrupt-controller; | |
| 7e0a51a0 | 50 | #interrupt-cells = <1>; |
| 84919b96 LW |
51 | |
| 52 | tc3589x_gpio { | |
| 7e0a51a0 LW |
53 | compatible = "toshiba,tc3589x-gpio"; |
| 54 | interrupts = <0>; | |
| 84919b96 LW |
55 | |
| 56 | interrupt-controller; | |
| 57 | #interrupt-cells = <2>; | |
| 58 | gpio-controller; | |
| 59 | #gpio-cells = <2>; | |
| 60 | }; | |
| 7e0a51a0 LW |
61 | tc3589x_keypad { |
| 62 | compatible = "toshiba,tc3589x-keypad"; | |
| 63 | interrupts = <6>; | |
| 64 | debounce-delay-ms = <4>; | |
| 65 | keypad,num-columns = <8>; | |
| 66 | keypad,num-rows = <8>; | |
| 67 | linux,no-autorepeat; | |
| 506822ea | 68 | wakeup-source; |
| 7e0a51a0 LW |
69 | linux,keymap = <0x0301006b |
| 70 | 0x04010066 | |
| 71 | 0x06040072 | |
| 72 | 0x040200d7 | |
| 73 | 0x0303006a | |
| 74 | 0x0205000e | |
| 75 | 0x0607008b | |
| 76 | 0x0500001c | |
| 77 | 0x0403000b | |
| 78 | 0x03040034 | |
| 79 | 0x05020067 | |
| 80 | 0x0305006c | |
| 81 | 0x040500e7 | |
| 82 | 0x0005009e | |
| 83 | 0x06020073 | |
| 84 | 0x01030039 | |
| 85 | 0x07060069 | |
| 86 | 0x050500d9>; | |
| 87 | }; | |
| 84919b96 LW |
88 | }; |
| 89 | }; | |
| d0e3bc81 LW |
90 | /* Sensors mounted on this board variant */ |
| 91 | i2c@80128000 { | |
| 92 | lsm303dlh@18 { | |
| 93 | /* Accelerometer */ | |
| 94 | compatible = "st,lsm303dlh-accel"; | |
| 95 | st,drdy-int-pin = <1>; | |
| 7ba5dd53 | 96 | drive-open-drain; |
| d0e3bc81 LW |
97 | reg = <0x18>; |
| 98 | vdd-supply = <&ab8500_ldo_aux1_reg>; | |
| 99 | vddio-supply = <&db8500_vsmps2_reg>; | |
| 100 | pinctrl-names = "default"; | |
| 101 | pinctrl-0 = <&accel_tvk_mode>; | |
| 22a93167 | 102 | interrupt-parent = <&gpio2>; |
| 7ba5dd53 LW |
103 | interrupts = <18 IRQ_TYPE_EDGE_FALLING>, |
| 104 | <19 IRQ_TYPE_EDGE_FALLING>; | |
| d0e3bc81 | 105 | }; |
| 93deea9a | 106 | lsm303dlh@1e { |
| 2f23cda3 LW |
107 | /* |
| 108 | * This magnetometer is packaged with | |
| 109 | * the accelerometer, and has a DRDY line, | |
| 110 | * however it is not connected on this | |
| 111 | * board so it can not generate interrupts. | |
| 112 | */ | |
| 93deea9a | 113 | compatible = "st,lsm303dlh-magn"; |
| d0e3bc81 LW |
114 | reg = <0x1e>; |
| 115 | vdd-supply = <&ab8500_ldo_aux1_reg>; | |
| 116 | vddio-supply = <&db8500_vsmps2_reg>; | |
| 2f23cda3 LW |
117 | }; |
| 118 | lis331dl@1c { | |
| 119 | /* Accelerometer */ | |
| 120 | compatible = "st,lis331dl-accel"; | |
| 121 | st,drdy-int-pin = <1>; | |
| 7ba5dd53 | 122 | drive-open-drain; |
| 2f23cda3 LW |
123 | reg = <0x1c>; |
| 124 | vdd-supply = <&ab8500_ldo_aux1_reg>; | |
| 125 | vddio-supply = <&db8500_vsmps2_reg>; | |
| 126 | pinctrl-names = "default"; | |
| 127 | pinctrl-0 = <&accel_tvk_mode>; | |
| 128 | interrupt-parent = <&gpio2>; | |
| 7ba5dd53 LW |
129 | interrupts = <18 IRQ_TYPE_EDGE_FALLING>, |
| 130 | <19 IRQ_TYPE_EDGE_FALLING>; | |
| 2f23cda3 LW |
131 | }; |
| 132 | ak8974@0f { | |
| 133 | /* Magnetometer */ | |
| 134 | compatible = "asahi-kasei,ak8974"; | |
| 135 | reg = <0x0f>; | |
| 136 | vdd-supply = <&ab8500_ldo_aux1_reg>; | |
| 137 | vddio-supply = <&db8500_vsmps2_reg>; | |
| d0e3bc81 | 138 | pinctrl-names = "default"; |
| 2f23cda3 LW |
139 | pinctrl-0 = <&gyro_magn_tvk_mode>; |
| 140 | interrupt-parent = <&gpio1>; | |
| 141 | interrupts = <0 IRQ_TYPE_EDGE_RISING>; | |
| d0e3bc81 LW |
142 | }; |
| 143 | l3g4200d@68 { | |
| 144 | /* Gyroscope */ | |
| 145 | compatible = "st,l3g4200d-gyro"; | |
| 146 | st,drdy-int-pin = <2>; | |
| 147 | reg = <0x68>; | |
| 148 | vdd-supply = <&ab8500_ldo_aux1_reg>; | |
| 149 | vddio-supply = <&db8500_vsmps2_reg>; | |
| 2f23cda3 LW |
150 | pinctrl-names = "default"; |
| 151 | pinctrl-0 = <&gyro_magn_tvk_mode>; | |
| 152 | interrupt-parent = <&gpio1>; | |
| 153 | interrupts = <0 IRQ_TYPE_EDGE_RISING>; | |
| d0e3bc81 LW |
154 | }; |
| 155 | lsp001wm@5c { | |
| 156 | /* Barometer/pressure sensor */ | |
| 157 | compatible = "st,lps001wp-press"; | |
| 158 | reg = <0x5c>; | |
| 159 | vdd-supply = <&ab8500_ldo_aux1_reg>; | |
| 160 | vddio-supply = <&db8500_vsmps2_reg>; | |
| 161 | }; | |
| 162 | }; | |
| 7ad86d61 LW |
163 | |
| 164 | i2c@80110000 { | |
| 165 | synaptics@4b { | |
| 166 | /* Synaptics RMI4 TM1217 touchscreen */ | |
| 167 | compatible = "syna,rmi4-i2c"; | |
| 168 | #address-cells = <1>; | |
| 169 | #size-cells = <0>; | |
| 170 | reg = <0x4b>; | |
| 171 | vdd-supply = <&ab8500_ldo_aux1_reg>; | |
| 172 | vddio-supply = <&db8500_vsmps2_reg>; | |
| 173 | pinctrl-names = "default"; | |
| 174 | pinctrl-0 = <&synaptics_tvk_mode>; | |
| 175 | interrupt-parent = <&gpio2>; | |
| 176 | interrupts = <20 IRQ_TYPE_EDGE_FALLING>; | |
| 177 | ||
| 178 | rmi-f01@1 { | |
| 179 | reg = <0x1>; | |
| 180 | syna,nosleep = <1>; | |
| 181 | }; | |
| 182 | rmi-f11@11 { | |
| 183 | reg = <0x11>; | |
| 184 | touchscreen-inverted-x; | |
| 185 | syna,sensor-type = <1>; | |
| 186 | }; | |
| 187 | }; | |
| 188 | }; | |
| 189 | ||
| a45cb698 LW |
190 | pinctrl { |
| 191 | /* Pull up this GPIO pin */ | |
| 192 | tc35893 { | |
| 193 | tc35893_tvk_mode: tc35893_tvk { | |
| 194 | tvk_cfg { | |
| 1637d480 | 195 | pins = "GPIO218_AH11"; |
| a45cb698 LW |
196 | ste,config = <&gpio_in_pu>; |
| 197 | }; | |
| 198 | }; | |
| 199 | }; | |
| 1a780d45 LW |
200 | prox { |
| 201 | prox_tvk_mode: prox_tvk { | |
| 202 | tvk_cfg { | |
| 1637d480 | 203 | pins = "GPIO217_AH12"; |
| 1a780d45 LW |
204 | ste,config = <&gpio_in_pu>; |
| 205 | }; | |
| 206 | }; | |
| 207 | }; | |
| 208 | hall { | |
| 209 | hall_tvk_mode: hall_tvk { | |
| 210 | tvk_cfg { | |
| 1637d480 | 211 | pins = "GPIO145_C13"; |
| 1a780d45 LW |
212 | ste,config = <&gpio_in_pu>; |
| 213 | }; | |
| 214 | }; | |
| 215 | }; | |
| d0e3bc81 LW |
216 | accelerometer { |
| 217 | accel_tvk_mode: accel_tvk { | |
| 218 | /* Accelerometer interrupt lines 1 & 2 */ | |
| 219 | tvk_cfg { | |
| 1637d480 | 220 | pins = "GPIO82_C1", "GPIO83_D3"; |
| 7ba5dd53 | 221 | ste,config = <&gpio_in_pu>; |
| d0e3bc81 LW |
222 | }; |
| 223 | }; | |
| 224 | }; | |
| 2f23cda3 LW |
225 | gyroscope { |
| 226 | /* | |
| 227 | * These lines are shared between Gyroscope l3g400dh | |
| 228 | * and AK8974 magnetometer. | |
| 229 | */ | |
| 230 | gyro_magn_tvk_mode: gyro_magn_tvk { | |
| 231 | /* GPIO 31 used for INT pull down the line */ | |
| d0e3bc81 | 232 | tvk_cfg1 { |
| 1637d480 | 233 | pins = "GPIO31_V3"; |
| 2f23cda3 | 234 | ste,config = <&gpio_in_pd>; |
| d0e3bc81 | 235 | }; |
| 2f23cda3 | 236 | /* GPIO 32 used for DRDY, pull this down */ |
| d0e3bc81 | 237 | tvk_cfg2 { |
| 1637d480 | 238 | pins = "GPIO32_V2"; |
| d0e3bc81 LW |
239 | ste,config = <&gpio_in_pd>; |
| 240 | }; | |
| 241 | }; | |
| 242 | }; | |
| 7ad86d61 LW |
243 | synaptics { |
| 244 | synaptics_tvk_mode: synaptics_tvk { | |
| 245 | /* Touchscreen uses GPIO 84 */ | |
| 246 | tvk_cfg1 { | |
| 247 | pins = "GPIO84_C2"; | |
| 248 | ste,config = <&gpio_in_pu>; | |
| 249 | }; | |
| 250 | }; | |
| 251 | }; | |
| a45cb698 | 252 | }; |
| 9c19cfa9 LW |
253 | }; |
| 254 | }; |