Commit | Line | Data |
---|---|---|
ca0a789a AV |
1 | /* |
2 | * linux/arch/arm/mach-at91/board-usb-a9263.c | |
3 | * | |
4 | * Copyright (C) 2005 SAN People | |
5 | * Copyright (C) 2007 Atmel Corporation. | |
6 | * Copyright (C) 2007 Calao-systems | |
7 | * | |
8 | * This program is free software; you can redistribute it and/or modify | |
9 | * it under the terms of the GNU General Public License as published by | |
10 | * the Free Software Foundation; either version 2 of the License, or | |
11 | * (at your option) any later version. | |
12 | * | |
13 | * This program is distributed in the hope that it will be useful, | |
14 | * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
15 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
16 | * GNU General Public License for more details. | |
17 | * | |
18 | * You should have received a copy of the GNU General Public License | |
19 | * along with this program; if not, write to the Free Software | |
20 | * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA | |
21 | */ | |
22 | ||
23 | #include <linux/types.h> | |
24 | #include <linux/init.h> | |
25 | #include <linux/mm.h> | |
26 | #include <linux/module.h> | |
27 | #include <linux/platform_device.h> | |
28 | #include <linux/spi/spi.h> | |
29 | #include <linux/gpio_keys.h> | |
30 | #include <linux/input.h> | |
31 | ||
ca0a789a AV |
32 | #include <asm/setup.h> |
33 | #include <asm/mach-types.h> | |
34 | #include <asm/irq.h> | |
35 | ||
36 | #include <asm/mach/arch.h> | |
37 | #include <asm/mach/map.h> | |
38 | #include <asm/mach/irq.h> | |
39 | ||
e505240b | 40 | #include <mach/hardware.h> |
a09e64fb RK |
41 | #include <mach/board.h> |
42 | #include <mach/gpio.h> | |
43 | #include <mach/at91_shdwc.h> | |
ca0a789a AV |
44 | |
45 | #include "generic.h" | |
46 | ||
47 | ||
48 | static void __init ek_map_io(void) | |
49 | { | |
50 | /* Initialize processor: 12.00 MHz crystal */ | |
51 | at91sam9263_initialize(12000000); | |
52 | ||
53 | /* DGBU on ttyS0. (Rx & Tx only) */ | |
54 | at91_register_uart(0, 0, 0); | |
55 | ||
56 | /* set serial console to ttyS0 (ie, DBGU) */ | |
57 | at91_set_serial_console(0); | |
58 | } | |
59 | ||
60 | static void __init ek_init_irq(void) | |
61 | { | |
62 | at91sam9263_init_interrupts(NULL); | |
63 | } | |
64 | ||
65 | ||
66 | /* | |
67 | * USB Host port | |
68 | */ | |
69 | static struct at91_usbh_data __initdata ek_usbh_data = { | |
70 | .ports = 2, | |
71 | }; | |
72 | ||
73 | /* | |
74 | * USB Device port | |
75 | */ | |
76 | static struct at91_udc_data __initdata ek_udc_data = { | |
77 | .vbus_pin = AT91_PIN_PB11, | |
78 | .pullup_pin = 0, /* pull-up driven by UDC */ | |
79 | }; | |
80 | ||
81 | /* | |
82 | * SPI devices. | |
83 | */ | |
84 | static struct spi_board_info ek_spi_devices[] = { | |
85 | #if !defined(CONFIG_MMC_AT91) | |
86 | { /* DataFlash chip */ | |
87 | .modalias = "mtd_dataflash", | |
88 | .chip_select = 0, | |
89 | .max_speed_hz = 15 * 1000 * 1000, | |
90 | .bus_num = 0, | |
91 | } | |
92 | #endif | |
93 | }; | |
94 | ||
95 | /* | |
96 | * MACB Ethernet device | |
97 | */ | |
98 | static struct at91_eth_data __initdata ek_macb_data = { | |
99 | .phy_irq_pin = AT91_PIN_PE31, | |
100 | .is_rmii = 1, | |
101 | }; | |
102 | ||
103 | /* | |
104 | * NAND flash | |
105 | */ | |
106 | static struct mtd_partition __initdata ek_nand_partition[] = { | |
107 | { | |
108 | .name = "Linux Kernel", | |
e505240b AV |
109 | .offset = 0, |
110 | .size = SZ_16M, | |
ca0a789a AV |
111 | }, |
112 | { | |
113 | .name = "Root FS", | |
e505240b AV |
114 | .offset = MTDPART_OFS_NXTBLK, |
115 | .size = 120 * SZ_1M, | |
ca0a789a AV |
116 | }, |
117 | { | |
118 | .name = "FS", | |
e505240b AV |
119 | .offset = MTDPART_OFS_NXTBLK, |
120 | .size = 120 * SZ_1M, | |
ca0a789a AV |
121 | } |
122 | }; | |
123 | ||
124 | static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) | |
125 | { | |
126 | *num_partitions = ARRAY_SIZE(ek_nand_partition); | |
127 | return ek_nand_partition; | |
128 | } | |
129 | ||
7c896834 | 130 | static struct atmel_nand_data __initdata ek_nand_data = { |
ca0a789a AV |
131 | .ale = 21, |
132 | .cle = 22, | |
133 | // .det_pin = ... not connected | |
134 | .rdy_pin = AT91_PIN_PA22, | |
135 | .enable_pin = AT91_PIN_PD15, | |
136 | .partition_info = nand_partitions, | |
f6ed6f78 | 137 | #if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) |
ca0a789a AV |
138 | .bus_width_16 = 1, |
139 | #else | |
140 | .bus_width_16 = 0, | |
141 | #endif | |
142 | }; | |
143 | ||
144 | /* | |
145 | * GPIO Buttons | |
146 | */ | |
147 | #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) | |
148 | static struct gpio_keys_button ek_buttons[] = { | |
149 | { /* USER PUSH BUTTON */ | |
150 | .code = KEY_ENTER, | |
151 | .gpio = AT91_PIN_PB10, | |
152 | .active_low = 1, | |
153 | .desc = "user_pb", | |
154 | .wakeup = 1, | |
155 | } | |
156 | }; | |
157 | ||
158 | static struct gpio_keys_platform_data ek_button_data = { | |
159 | .buttons = ek_buttons, | |
160 | .nbuttons = ARRAY_SIZE(ek_buttons), | |
161 | }; | |
162 | ||
163 | static struct platform_device ek_button_device = { | |
164 | .name = "gpio-keys", | |
165 | .id = -1, | |
166 | .num_resources = 0, | |
167 | .dev = { | |
168 | .platform_data = &ek_button_data, | |
169 | } | |
170 | }; | |
171 | ||
172 | static void __init ek_add_device_buttons(void) | |
173 | { | |
174 | at91_set_GPIO_periph(AT91_PIN_PB10, 1); /* user push button, pull up enabled */ | |
175 | at91_set_deglitch(AT91_PIN_PB10, 1); | |
176 | ||
177 | platform_device_register(&ek_button_device); | |
178 | } | |
179 | #else | |
180 | static void __init ek_add_device_buttons(void) {} | |
181 | #endif | |
182 | ||
183 | /* | |
184 | * LEDs | |
185 | */ | |
186 | static struct gpio_led ek_leds[] = { | |
187 | { /* user_led (green) */ | |
188 | .name = "user_led", | |
189 | .gpio = AT91_PIN_PB21, | |
190 | .active_low = 1, | |
191 | .default_trigger = "heartbeat", | |
192 | } | |
193 | }; | |
194 | ||
195 | ||
196 | static void __init ek_board_init(void) | |
197 | { | |
198 | /* Serial */ | |
199 | at91_add_device_serial(); | |
200 | /* USB Host */ | |
201 | at91_add_device_usbh(&ek_usbh_data); | |
202 | /* USB Device */ | |
203 | at91_add_device_udc(&ek_udc_data); | |
204 | /* SPI */ | |
205 | at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); | |
206 | /* Ethernet */ | |
207 | at91_add_device_eth(&ek_macb_data); | |
208 | /* NAND */ | |
209 | at91_add_device_nand(&ek_nand_data); | |
210 | /* I2C */ | |
211 | at91_add_device_i2c(NULL, 0); | |
212 | /* Push Buttons */ | |
213 | ek_add_device_buttons(); | |
214 | /* LEDs */ | |
215 | at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); | |
216 | /* shutdown controller, wakeup button (5 msec low) */ | |
217 | at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW | |
218 | | AT91_SHDW_RTTWKEN); | |
219 | } | |
220 | ||
221 | MACHINE_START(USB_A9263, "CALAO USB_A9263") | |
222 | /* Maintainer: calao-systems */ | |
223 | .phys_io = AT91_BASE_SYS, | |
224 | .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, | |
225 | .boot_params = AT91_SDRAM_BASE + 0x100, | |
226 | .timer = &at91sam926x_timer, | |
227 | .map_io = ek_map_io, | |
228 | .init_irq = ek_init_irq, | |
229 | .init_machine = ek_board_init, | |
230 | MACHINE_END |