Commit | Line | Data |
---|---|---|
49265651 NK |
1 | /* |
2 | * linux/arch/arm/mach-omap2/board-ldp.c | |
3 | * | |
4 | * Copyright (C) 2008 Texas Instruments Inc. | |
5 | * Nishant Kamat <nskamat@ti.com> | |
6 | * | |
7 | * Modified from mach-omap2/board-3430sdp.c | |
8 | * | |
9 | * This program is free software; you can redistribute it and/or modify | |
10 | * it under the terms of the GNU General Public License version 2 as | |
11 | * published by the Free Software Foundation. | |
12 | */ | |
13 | ||
14 | #include <linux/kernel.h> | |
15 | #include <linux/init.h> | |
16 | #include <linux/platform_device.h> | |
17 | #include <linux/delay.h> | |
18 | #include <linux/input.h> | |
6135434a | 19 | #include <linux/input/matrix_keypad.h> |
4a899d5e | 20 | #include <linux/gpio_keys.h> |
49265651 NK |
21 | #include <linux/workqueue.h> |
22 | #include <linux/err.h> | |
23 | #include <linux/clk.h> | |
24 | #include <linux/spi/spi.h> | |
25 | #include <linux/spi/ads7846.h> | |
4a899d5e | 26 | #include <linux/regulator/machine.h> |
90c62bf0 | 27 | #include <linux/i2c/twl4030.h> |
99730225 | 28 | #include <linux/io.h> |
1c0e147e | 29 | #include <linux/smsc911x.h> |
49265651 NK |
30 | |
31 | #include <mach/hardware.h> | |
32 | #include <asm/mach-types.h> | |
33 | #include <asm/mach/arch.h> | |
34 | #include <asm/mach/map.h> | |
35 | ||
ce491cf8 | 36 | #include <plat/mcspi.h> |
49265651 | 37 | #include <mach/gpio.h> |
ce491cf8 TL |
38 | #include <plat/board.h> |
39 | #include <plat/common.h> | |
40 | #include <plat/gpmc.h> | |
49265651 | 41 | |
49265651 | 42 | #include <asm/delay.h> |
ce491cf8 TL |
43 | #include <plat/control.h> |
44 | #include <plat/usb.h> | |
49265651 | 45 | |
ca5742bd | 46 | #include "mux.h" |
90c62bf0 TL |
47 | #include "mmc-twl4030.h" |
48 | ||
1c0e147e SG |
49 | #define LDP_SMSC911X_CS 1 |
50 | #define LDP_SMSC911X_GPIO 152 | |
ec7558a6 TL |
51 | #define DEBUG_BASE 0x08000000 |
52 | #define LDP_ETHR_START DEBUG_BASE | |
b1c056d2 | 53 | |
1c0e147e | 54 | static struct resource ldp_smsc911x_resources[] = { |
b1c056d2 | 55 | [0] = { |
ec7558a6 TL |
56 | .start = LDP_ETHR_START, |
57 | .end = LDP_ETHR_START + SZ_4K, | |
b1c056d2 SM |
58 | .flags = IORESOURCE_MEM, |
59 | }, | |
60 | [1] = { | |
61 | .start = 0, | |
62 | .end = 0, | |
63 | .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, | |
64 | }, | |
65 | }; | |
66 | ||
1c0e147e SG |
67 | static struct smsc911x_platform_config ldp_smsc911x_config = { |
68 | .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, | |
69 | .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, | |
70 | .flags = SMSC911X_USE_32BIT, | |
71 | .phy_interface = PHY_INTERFACE_MODE_MII, | |
72 | }; | |
73 | ||
74 | static struct platform_device ldp_smsc911x_device = { | |
75 | .name = "smsc911x", | |
b1c056d2 | 76 | .id = -1, |
1c0e147e SG |
77 | .num_resources = ARRAY_SIZE(ldp_smsc911x_resources), |
78 | .resource = ldp_smsc911x_resources, | |
79 | .dev = { | |
80 | .platform_data = &ldp_smsc911x_config, | |
81 | }, | |
b1c056d2 SM |
82 | }; |
83 | ||
4f543332 | 84 | static int board_keymap[] = { |
4a899d5e TL |
85 | KEY(0, 0, KEY_1), |
86 | KEY(1, 0, KEY_2), | |
87 | KEY(2, 0, KEY_3), | |
88 | KEY(0, 1, KEY_4), | |
89 | KEY(1, 1, KEY_5), | |
90 | KEY(2, 1, KEY_6), | |
91 | KEY(3, 1, KEY_F5), | |
92 | KEY(0, 2, KEY_7), | |
93 | KEY(1, 2, KEY_8), | |
94 | KEY(2, 2, KEY_9), | |
95 | KEY(3, 2, KEY_F6), | |
96 | KEY(0, 3, KEY_F7), | |
97 | KEY(1, 3, KEY_0), | |
98 | KEY(2, 3, KEY_F8), | |
99 | PERSISTENT_KEY(4, 5), | |
100 | KEY(4, 4, KEY_VOLUMEUP), | |
101 | KEY(5, 5, KEY_VOLUMEDOWN), | |
102 | 0 | |
103 | }; | |
104 | ||
4f543332 TL |
105 | static struct matrix_keymap_data board_map_data = { |
106 | .keymap = board_keymap, | |
107 | .keymap_size = ARRAY_SIZE(board_keymap), | |
108 | }; | |
109 | ||
4a899d5e | 110 | static struct twl4030_keypad_data ldp_kp_twl4030_data = { |
4f543332 | 111 | .keymap_data = &board_map_data, |
4a899d5e TL |
112 | .rows = 6, |
113 | .cols = 6, | |
4a899d5e TL |
114 | .rep = 1, |
115 | }; | |
116 | ||
117 | static struct gpio_keys_button ldp_gpio_keys_buttons[] = { | |
118 | [0] = { | |
119 | .code = KEY_ENTER, | |
120 | .gpio = 101, | |
121 | .desc = "enter sw", | |
122 | .active_low = 1, | |
123 | .debounce_interval = 30, | |
124 | }, | |
125 | [1] = { | |
126 | .code = KEY_F1, | |
127 | .gpio = 102, | |
128 | .desc = "func 1", | |
129 | .active_low = 1, | |
130 | .debounce_interval = 30, | |
131 | }, | |
132 | [2] = { | |
133 | .code = KEY_F2, | |
134 | .gpio = 103, | |
135 | .desc = "func 2", | |
136 | .active_low = 1, | |
137 | .debounce_interval = 30, | |
138 | }, | |
139 | [3] = { | |
140 | .code = KEY_F3, | |
141 | .gpio = 104, | |
142 | .desc = "func 3", | |
143 | .active_low = 1, | |
144 | .debounce_interval = 30, | |
145 | }, | |
146 | [4] = { | |
147 | .code = KEY_F4, | |
148 | .gpio = 105, | |
149 | .desc = "func 4", | |
150 | .active_low = 1, | |
151 | .debounce_interval = 30, | |
152 | }, | |
153 | [5] = { | |
154 | .code = KEY_LEFT, | |
155 | .gpio = 106, | |
156 | .desc = "left sw", | |
157 | .active_low = 1, | |
158 | .debounce_interval = 30, | |
159 | }, | |
160 | [6] = { | |
161 | .code = KEY_RIGHT, | |
162 | .gpio = 107, | |
163 | .desc = "right sw", | |
164 | .active_low = 1, | |
165 | .debounce_interval = 30, | |
166 | }, | |
167 | [7] = { | |
168 | .code = KEY_UP, | |
169 | .gpio = 108, | |
170 | .desc = "up sw", | |
171 | .active_low = 1, | |
172 | .debounce_interval = 30, | |
173 | }, | |
174 | [8] = { | |
175 | .code = KEY_DOWN, | |
176 | .gpio = 109, | |
177 | .desc = "down sw", | |
178 | .active_low = 1, | |
179 | .debounce_interval = 30, | |
180 | }, | |
181 | }; | |
182 | ||
183 | static struct gpio_keys_platform_data ldp_gpio_keys = { | |
184 | .buttons = ldp_gpio_keys_buttons, | |
185 | .nbuttons = ARRAY_SIZE(ldp_gpio_keys_buttons), | |
186 | .rep = 1, | |
187 | }; | |
188 | ||
189 | static struct platform_device ldp_gpio_keys_device = { | |
190 | .name = "gpio-keys", | |
191 | .id = -1, | |
192 | .dev = { | |
193 | .platform_data = &ldp_gpio_keys, | |
194 | }, | |
195 | }; | |
196 | ||
197 | static int ts_gpio; | |
198 | ||
199 | /** | |
200 | * @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq | |
201 | * | |
202 | * @return - void. If request gpio fails then Flag KERN_ERR. | |
203 | */ | |
204 | static void ads7846_dev_init(void) | |
205 | { | |
206 | if (gpio_request(ts_gpio, "ads7846 irq") < 0) { | |
207 | printk(KERN_ERR "can't get ads746 pen down GPIO\n"); | |
208 | return; | |
209 | } | |
210 | ||
211 | gpio_direction_input(ts_gpio); | |
212 | omap_set_gpio_debounce(ts_gpio, 1); | |
213 | omap_set_gpio_debounce_time(ts_gpio, 0xa); | |
214 | } | |
215 | ||
216 | static int ads7846_get_pendown_state(void) | |
217 | { | |
218 | return !gpio_get_value(ts_gpio); | |
219 | } | |
220 | ||
221 | static struct ads7846_platform_data tsc2046_config __initdata = { | |
222 | .get_pendown_state = ads7846_get_pendown_state, | |
223 | .keep_vref_on = 1, | |
224 | }; | |
225 | ||
226 | static struct omap2_mcspi_device_config tsc2046_mcspi_config = { | |
227 | .turbo_mode = 0, | |
228 | .single_channel = 1, /* 0: slave, 1: master */ | |
229 | }; | |
230 | ||
231 | static struct spi_board_info ldp_spi_board_info[] __initdata = { | |
232 | [0] = { | |
233 | /* | |
234 | * TSC2046 operates at a max freqency of 2MHz, so | |
235 | * operate slightly below at 1.5MHz | |
236 | */ | |
237 | .modalias = "ads7846", | |
238 | .bus_num = 1, | |
239 | .chip_select = 0, | |
240 | .max_speed_hz = 1500000, | |
241 | .controller_data = &tsc2046_mcspi_config, | |
242 | .irq = 0, | |
243 | .platform_data = &tsc2046_config, | |
244 | }, | |
245 | }; | |
246 | ||
1c0e147e | 247 | static inline void __init ldp_init_smsc911x(void) |
b1c056d2 SM |
248 | { |
249 | int eth_cs; | |
250 | unsigned long cs_mem_base; | |
251 | int eth_gpio = 0; | |
252 | ||
1c0e147e | 253 | eth_cs = LDP_SMSC911X_CS; |
b1c056d2 SM |
254 | |
255 | if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) { | |
1c0e147e | 256 | printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n"); |
b1c056d2 SM |
257 | return; |
258 | } | |
259 | ||
1c0e147e SG |
260 | ldp_smsc911x_resources[0].start = cs_mem_base + 0x0; |
261 | ldp_smsc911x_resources[0].end = cs_mem_base + 0xff; | |
b1c056d2 SM |
262 | udelay(100); |
263 | ||
1c0e147e | 264 | eth_gpio = LDP_SMSC911X_GPIO; |
b1c056d2 | 265 | |
1c0e147e | 266 | ldp_smsc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio); |
b1c056d2 | 267 | |
1c0e147e SG |
268 | if (gpio_request(eth_gpio, "smsc911x irq") < 0) { |
269 | printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n", | |
b1c056d2 SM |
270 | eth_gpio); |
271 | return; | |
272 | } | |
273 | gpio_direction_input(eth_gpio); | |
274 | } | |
275 | ||
49adf465 ID |
276 | static struct platform_device ldp_lcd_device = { |
277 | .name = "ldp_lcd", | |
278 | .id = -1, | |
279 | }; | |
280 | ||
281 | static struct omap_lcd_config ldp_lcd_config __initdata = { | |
282 | .ctrl_name = "internal", | |
283 | }; | |
284 | ||
49265651 | 285 | static struct omap_board_config_kernel ldp_config[] __initdata = { |
49adf465 | 286 | { OMAP_TAG_LCD, &ldp_lcd_config }, |
49265651 NK |
287 | }; |
288 | ||
b3c6df3a PW |
289 | static void __init omap_ldp_init_irq(void) |
290 | { | |
291 | omap_board_config = ldp_config; | |
292 | omap_board_config_size = ARRAY_SIZE(ldp_config); | |
293 | omap2_init_common_hw(NULL, NULL); | |
294 | omap_init_irq(); | |
295 | omap_gpio_init(); | |
296 | ldp_init_smsc911x(); | |
297 | } | |
298 | ||
4a899d5e TL |
299 | static struct twl4030_usb_data ldp_usb_data = { |
300 | .usb_mode = T2_USB_MODE_ULPI, | |
301 | }; | |
302 | ||
90c62bf0 TL |
303 | static struct twl4030_gpio_platform_data ldp_gpio_data = { |
304 | .gpio_base = OMAP_MAX_GPIO_LINES, | |
305 | .irq_base = TWL4030_GPIO_IRQ_BASE, | |
306 | .irq_end = TWL4030_GPIO_IRQ_END, | |
307 | }; | |
308 | ||
4a899d5e TL |
309 | static struct twl4030_madc_platform_data ldp_madc_data = { |
310 | .irq_line = 1, | |
311 | }; | |
312 | ||
313 | static struct regulator_consumer_supply ldp_vmmc1_supply = { | |
314 | .supply = "vmmc", | |
315 | }; | |
316 | ||
317 | /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */ | |
318 | static struct regulator_init_data ldp_vmmc1 = { | |
319 | .constraints = { | |
320 | .min_uV = 1850000, | |
321 | .max_uV = 3150000, | |
322 | .valid_modes_mask = REGULATOR_MODE_NORMAL | |
323 | | REGULATOR_MODE_STANDBY, | |
324 | .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | |
325 | | REGULATOR_CHANGE_MODE | |
326 | | REGULATOR_CHANGE_STATUS, | |
327 | }, | |
328 | .num_consumer_supplies = 1, | |
329 | .consumer_supplies = &ldp_vmmc1_supply, | |
330 | }; | |
331 | ||
90c62bf0 TL |
332 | static struct twl4030_platform_data ldp_twldata = { |
333 | .irq_base = TWL4030_IRQ_BASE, | |
334 | .irq_end = TWL4030_IRQ_END, | |
335 | ||
336 | /* platform_data for children goes here */ | |
4a899d5e TL |
337 | .madc = &ldp_madc_data, |
338 | .usb = &ldp_usb_data, | |
339 | .vmmc1 = &ldp_vmmc1, | |
90c62bf0 | 340 | .gpio = &ldp_gpio_data, |
4a899d5e | 341 | .keypad = &ldp_kp_twl4030_data, |
90c62bf0 TL |
342 | }; |
343 | ||
344 | static struct i2c_board_info __initdata ldp_i2c_boardinfo[] = { | |
345 | { | |
346 | I2C_BOARD_INFO("twl4030", 0x48), | |
347 | .flags = I2C_CLIENT_WAKE, | |
348 | .irq = INT_34XX_SYS_NIRQ, | |
349 | .platform_data = &ldp_twldata, | |
350 | }, | |
351 | }; | |
352 | ||
49265651 NK |
353 | static int __init omap_i2c_init(void) |
354 | { | |
90c62bf0 TL |
355 | omap_register_i2c_bus(1, 2600, ldp_i2c_boardinfo, |
356 | ARRAY_SIZE(ldp_i2c_boardinfo)); | |
49265651 NK |
357 | omap_register_i2c_bus(2, 400, NULL, 0); |
358 | omap_register_i2c_bus(3, 400, NULL, 0); | |
359 | return 0; | |
360 | } | |
361 | ||
90c62bf0 TL |
362 | static struct twl4030_hsmmc_info mmc[] __initdata = { |
363 | { | |
364 | .mmc = 1, | |
365 | .wires = 4, | |
366 | .gpio_cd = -EINVAL, | |
367 | .gpio_wp = -EINVAL, | |
368 | }, | |
369 | {} /* Terminator */ | |
370 | }; | |
371 | ||
49adf465 ID |
372 | static struct platform_device *ldp_devices[] __initdata = { |
373 | &ldp_smsc911x_device, | |
374 | &ldp_lcd_device, | |
4a899d5e | 375 | &ldp_gpio_keys_device, |
49adf465 ID |
376 | }; |
377 | ||
ca5742bd TL |
378 | #ifdef CONFIG_OMAP_MUX |
379 | static struct omap_board_mux board_mux[] __initdata = { | |
380 | { .reg_offset = OMAP_MUX_TERMINATOR }, | |
381 | }; | |
382 | #else | |
383 | #define board_mux NULL | |
384 | #endif | |
385 | ||
49265651 NK |
386 | static void __init omap_ldp_init(void) |
387 | { | |
ca5742bd | 388 | omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); |
49265651 | 389 | omap_i2c_init(); |
b1c056d2 | 390 | platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices)); |
4a899d5e TL |
391 | ts_gpio = 54; |
392 | ldp_spi_board_info[0].irq = gpio_to_irq(ts_gpio); | |
393 | spi_register_board_info(ldp_spi_board_info, | |
394 | ARRAY_SIZE(ldp_spi_board_info)); | |
395 | ads7846_dev_init(); | |
49265651 | 396 | omap_serial_init(); |
18cb7aca | 397 | usb_musb_init(); |
4a899d5e TL |
398 | |
399 | twl4030_mmc_init(mmc); | |
400 | /* link regulators to MMC adapters */ | |
401 | ldp_vmmc1_supply.dev = mmc[0].dev; | |
49265651 NK |
402 | } |
403 | ||
404 | static void __init omap_ldp_map_io(void) | |
405 | { | |
406 | omap2_set_globals_343x(); | |
407 | omap2_map_common_io(); | |
408 | } | |
409 | ||
410 | MACHINE_START(OMAP_LDP, "OMAP LDP board") | |
411 | .phys_io = 0x48000000, | |
b4224b23 | 412 | .io_pg_offst = ((0xfa000000) >> 18) & 0xfffc, |
49265651 NK |
413 | .boot_params = 0x80000100, |
414 | .map_io = omap_ldp_map_io, | |
415 | .init_irq = omap_ldp_init_irq, | |
416 | .init_machine = omap_ldp_init, | |
417 | .timer = &omap_timer, | |
418 | MACHINE_END |