[deliverable/linux.git] / arch / arm / mach-omap2 / board-omap3beagle.c

/*
 * linux/arch/arm/mach-omap2/board-omap3beagle.c
 *
 * Copyright (C) 2008 Texas Instruments
 *
 * Modified from mach-omap2/board-3430sdp.c
 *
 * Initial code: Syed Mohammed Khasim
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/leds.h>
#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>
#include <linux/opp.h>

#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
#include <linux/mmc/host.h>

#include <linux/regulator/machine.h>
#include <linux/i2c/twl.h>

#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>

#include "common.h"
#include <video/omapdss.h>
#include <video/omap-panel-tfp410.h>
#include <plat/gpmc.h>
#include <plat/nand.h>
#include <plat/usb.h>
#include <plat/omap_device.h>

#include "mux.h"
#include "hsmmc.h"
#include "pm.h"
#include "common-board-devices.h"

/*
 * OMAP3 Beagle revision
 * Run time detection of Beagle revision is done by reading GPIO.
 * GPIO ID -
 *	AXBX	= GPIO173, GPIO172, GPIO171: 1 1 1
 *	C1_3	= GPIO173, GPIO172, GPIO171: 1 1 0
 *	C4	= GPIO173, GPIO172, GPIO171: 1 0 1
 *	XMA/XMB = GPIO173, GPIO172, GPIO171: 0 0 0
 *	XMC = GPIO173, GPIO172, GPIO171: 0 1 0
 */
enum {
	OMAP3BEAGLE_BOARD_UNKN = 0,
	OMAP3BEAGLE_BOARD_AXBX,
	OMAP3BEAGLE_BOARD_C1_3,
	OMAP3BEAGLE_BOARD_C4,
	OMAP3BEAGLE_BOARD_XM,
	OMAP3BEAGLE_BOARD_XMC,
};

static u8 omap3_beagle_version;

/*
 * Board-specific configuration
 * Defaults to BeagleBoard-xMC
 */
static struct {
	int mmc1_gpio_wp;
	int usb_pwr_level;
	int dvi_pd_gpio;
	int usr_button_gpio;
	int mmc_caps;
} beagle_config = {
	.mmc1_gpio_wp = -EINVAL,
	.usb_pwr_level = GPIOF_OUT_INIT_LOW,
	.dvi_pd_gpio = -EINVAL,
	.usr_button_gpio = 4,
	.mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
};

static struct gpio omap3_beagle_rev_gpios[] __initdata = {
	{ 171, GPIOF_IN, "rev_id_0"    },
	{ 172, GPIOF_IN, "rev_id_1" },
	{ 173, GPIOF_IN, "rev_id_2"    },
};

static void __init omap3_beagle_init_rev(void)
{
	int ret;
	u16 beagle_rev = 0;

	omap_mux_init_gpio(171, OMAP_PIN_INPUT_PULLUP);
	omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
	omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);

	ret = gpio_request_array(omap3_beagle_rev_gpios,
				 ARRAY_SIZE(omap3_beagle_rev_gpios));
	if (ret < 0) {
		printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
		omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
		return;
	}

	beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
			| (gpio_get_value(173) << 2);

	gpio_free_array(omap3_beagle_rev_gpios,
			ARRAY_SIZE(omap3_beagle_rev_gpios));

	switch (beagle_rev) {
	case 7:
		printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
		omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
		beagle_config.mmc1_gpio_wp = 29;
		beagle_config.dvi_pd_gpio = 170;
		beagle_config.usr_button_gpio = 7;
		break;
	case 6:
		printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
		omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
		beagle_config.mmc1_gpio_wp = 23;
		beagle_config.dvi_pd_gpio = 170;
		beagle_config.usr_button_gpio = 7;
		break;
	case 5:
		printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
		omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
		beagle_config.mmc1_gpio_wp = 23;
		beagle_config.dvi_pd_gpio = 170;
		beagle_config.usr_button_gpio = 7;
		break;
	case 0:
		printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n");
		omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
		beagle_config.usb_pwr_level = GPIOF_OUT_INIT_HIGH;
		beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
		break;
	case 2:
		printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n");
		omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC;
		beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
		break;
	default:
		printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
		omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
	}
}

static struct mtd_partition omap3beagle_nand_partitions[] = {
	/* All the partition sizes are listed in terms of NAND block size */
	{
		.name		= "X-Loader",
		.offset		= 0,
		.size		= 4 * NAND_BLOCK_SIZE,
		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
	},
	{
		.name		= "U-Boot",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
		.size		= 15 * NAND_BLOCK_SIZE,
		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
	},
	{
		.name		= "U-Boot Env",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x260000 */
		.size		= 1 * NAND_BLOCK_SIZE,
	},
	{
		.name		= "Kernel",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
		.size		= 32 * NAND_BLOCK_SIZE,
	},
	{
		.name		= "File System",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x680000 */
		.size		= MTDPART_SIZ_FULL,
	},
};

/* DSS */

static struct tfp410_platform_data dvi_panel = {
	.i2c_bus_num = 3,
	.power_down_gpio = -1,
};

static struct omap_dss_device beagle_dvi_device = {
	.type = OMAP_DISPLAY_TYPE_DPI,
	.name = "dvi",
	.driver_name = "tfp410",
	.data = &dvi_panel,
	.phy.dpi.data_lines = 24,
};

static struct omap_dss_device beagle_tv_device = {
	.name = "tv",
	.driver_name = "venc",
	.type = OMAP_DISPLAY_TYPE_VENC,
	.phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
};

static struct omap_dss_device *beagle_dss_devices[] = {
	&beagle_dvi_device,
	&beagle_tv_device,
};

static struct omap_dss_board_info beagle_dss_data = {
	.num_devices = ARRAY_SIZE(beagle_dss_devices),
	.devices = beagle_dss_devices,
	.default_device = &beagle_dvi_device,
};

#include "sdram-micron-mt46h32m32lf-6.h"

static struct omap2_hsmmc_info mmc[] = {
	{
		.mmc		= 1,
		.caps		= MMC_CAP_4_BIT_DATA,
		.gpio_wp	= -EINVAL,
		.deferred	= true,
	},
	{}	/* Terminator */
};

static struct regulator_consumer_supply beagle_vmmc1_supply[] = {
	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
};

static struct regulator_consumer_supply beagle_vsim_supply[] = {
	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
};

static struct gpio_led gpio_leds[];

static int beagle_twl_gpio_setup(struct device *dev,
		unsigned gpio, unsigned ngpio)
{
	int r;

	mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp;
	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
	mmc[0].gpio_cd = gpio + 0;
	omap_hsmmc_late_init(mmc);

	/*
	 * TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
	 * high / others active low)
	 * DVI reset GPIO is different between beagle revisions
	 */
	/* Valid for all -xM revisions */
	if (cpu_is_omap3630()) {
		/*
		 * gpio + 1 on Xm controls the TFP410's enable line (active low)
		 * gpio + 2 control varies depending on the board rev as below:
		 * P7/P8 revisions(prototype): Camera EN
		 * A2+ revisions (production): LDO (DVI, serial, led blocks)
		 */
		r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW,
				     "nDVI_PWR_EN");
		if (r)
			pr_err("%s: unable to configure nDVI_PWR_EN\n",
				__func__);

		beagle_config.dvi_pd_gpio = gpio + 2;

	} else {
		/*
		 * REVISIT: need ehci-omap hooks for external VBUS
		 * power switch and overcurrent detect
		 */
		if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
			pr_err("%s: unable to configure EHCI_nOC\n", __func__);
	}
	dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio;

	gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
			"nEN_USB_PWR");

	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;

	return 0;
}

static struct twl4030_gpio_platform_data beagle_gpio_data = {
	.use_leds	= true,
	.pullups	= BIT(1),
	.pulldowns	= BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
				| BIT(15) | BIT(16) | BIT(17),
	.setup		= beagle_twl_gpio_setup,
};

/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
static struct regulator_init_data beagle_vmmc1 = {
	.constraints = {
		.min_uV			= 1850000,
		.max_uV			= 3150000,
		.valid_modes_mask	= REGULATOR_MODE_NORMAL
					| REGULATOR_MODE_STANDBY,
		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
					| REGULATOR_CHANGE_MODE
					| REGULATOR_CHANGE_STATUS,
	},
	.num_consumer_supplies	= ARRAY_SIZE(beagle_vmmc1_supply),
	.consumer_supplies	= beagle_vmmc1_supply,
};

/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
static struct regulator_init_data beagle_vsim = {
	.constraints = {
		.min_uV			= 1800000,
		.max_uV			= 3000000,
		.valid_modes_mask	= REGULATOR_MODE_NORMAL
					| REGULATOR_MODE_STANDBY,
		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
					| REGULATOR_CHANGE_MODE
					| REGULATOR_CHANGE_STATUS,
	},
	.num_consumer_supplies	= ARRAY_SIZE(beagle_vsim_supply),
	.consumer_supplies	= beagle_vsim_supply,
};

static struct twl4030_platform_data beagle_twldata = {
	/* platform_data for children goes here */
	.gpio		= &beagle_gpio_data,
	.vmmc1		= &beagle_vmmc1,
	.vsim		= &beagle_vsim,
};

static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
       {
               I2C_BOARD_INFO("eeprom", 0x50),
       },
};

static int __init omap3_beagle_i2c_init(void)
{
	omap3_pmic_get_config(&beagle_twldata,
			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
			TWL_COMMON_PDATA_AUDIO,
			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);

	beagle_twldata.vpll2->constraints.name = "VDVI";

	omap3_pmic_init("twl4030", &beagle_twldata);
	/* Bus 3 is attached to the DVI port where devices like the pico DLP
	 * projector don't work reliably with 400kHz */
	omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
	return 0;
}

static struct gpio_led gpio_leds[] = {
	{
		.name			= "beagleboard::usr0",
		.default_trigger	= "heartbeat",
		.gpio			= 150,
	},
	{
		.name			= "beagleboard::usr1",
		.default_trigger	= "mmc0",
		.gpio			= 149,
	},
	{
		.name			= "beagleboard::pmu_stat",
		.gpio			= -EINVAL,	/* gets replaced */
		.active_low		= true,
	},
};

static struct gpio_led_platform_data gpio_led_info = {
	.leds		= gpio_leds,
	.num_leds	= ARRAY_SIZE(gpio_leds),
};

static struct platform_device leds_gpio = {
	.name	= "leds-gpio",
	.id	= -1,
	.dev	= {
		.platform_data	= &gpio_led_info,
	},
};

static struct gpio_keys_button gpio_buttons[] = {
	{
		.code			= BTN_EXTRA,
		/* Dynamically assigned depending on board */
		.gpio			= -EINVAL,
		.desc			= "user",
		.wakeup			= 1,
	},
};

static struct gpio_keys_platform_data gpio_key_info = {
	.buttons	= gpio_buttons,
	.nbuttons	= ARRAY_SIZE(gpio_buttons),
};

static struct platform_device keys_gpio = {
	.name	= "gpio-keys",
	.id	= -1,
	.dev	= {
		.platform_data	= &gpio_key_info,
	},
};

static struct platform_device madc_hwmon = {
	.name	= "twl4030_madc_hwmon",
	.id	= -1,
};

static struct platform_device *omap3_beagle_devices[] __initdata = {
	&leds_gpio,
	&keys_gpio,
	&madc_hwmon,
};

static const struct usbhs_omap_board_data usbhs_bdata __initconst = {

	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,

	.phy_reset  = true,
	.reset_gpio_port[0]  = -EINVAL,
	.reset_gpio_port[1]  = 147,
	.reset_gpio_port[2]  = -EINVAL
};

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif

static void __init beagle_opp_init(void)
{
	int r = 0;

	/* Initialize the omap3 opp table */
	if (omap3_opp_init()) {
		pr_err("%s: opp default init failed\n", __func__);
		return;
	}

	/* Custom OPP enabled for all xM versions */
	if (cpu_is_omap3630()) {
		struct device *mpu_dev, *iva_dev;

		mpu_dev = omap_device_get_by_hwmod_name("mpu");
		iva_dev = omap_device_get_by_hwmod_name("iva");

		if (!mpu_dev || !iva_dev) {
			pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
				__func__, mpu_dev, iva_dev);
			return;
		}
		/* Enable MPU 1GHz and lower opps */
		r = opp_enable(mpu_dev, 800000000);
		/* TODO: MPU 1GHz needs SR and ABB */

		/* Enable IVA 800MHz and lower opps */
		r |= opp_enable(iva_dev, 660000000);
		/* TODO: DSP 800MHz needs SR and ABB */
		if (r) {
			pr_err("%s: failed to enable higher opp %d\n",
				__func__, r);
			/*
			 * Cleanup - disable the higher freqs - we dont care
			 * about the results
			 */
			opp_disable(mpu_dev, 800000000);
			opp_disable(iva_dev, 660000000);
		}
	}
	return;
}

static void __init omap3_beagle_init(void)
{
	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
	omap3_beagle_init_rev();

	if (gpio_is_valid(beagle_config.mmc1_gpio_wp))
		omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
	mmc[0].caps = beagle_config.mmc_caps;
	omap_hsmmc_init(mmc);

	omap3_beagle_i2c_init();

	gpio_buttons[0].gpio = beagle_config.usr_button_gpio;

	platform_add_devices(omap3_beagle_devices,
			ARRAY_SIZE(omap3_beagle_devices));
	if (gpio_is_valid(beagle_config.dvi_pd_gpio))
		omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT);
	omap_display_init(&beagle_dss_data);
	omap_serial_init();
	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
				  mt46h32m32lf6_sdrc_params);

	usb_musb_init(NULL);
	usbhs_init(&usbhs_bdata);
	omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
			     ARRAY_SIZE(omap3beagle_nand_partitions));

	/* Ensure msecure is mux'd to be able to set the RTC. */
	omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);

	/* Ensure SDRC pins are mux'd for self-refresh */
	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);

	beagle_opp_init();
}

MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
	/* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
	.atag_offset	= 0x100,
	.reserve	= omap_reserve,
	.map_io		= omap3_map_io,
	.init_early	= omap3_init_early,
	.init_irq	= omap3_init_irq,
	.handle_irq	= omap3_intc_handle_irq,
	.init_machine	= omap3_beagle_init,
	.init_late	= omap3_init_late,
	.timer		= &omap3_secure_timer,
	.restart	= omap_prcm_restart,
MACHINE_END
Commit	Line	Data
2885f000 SMK	1	/*
	2	* linux/arch/arm/mach-omap2/board-omap3beagle.c
	3	*
	4	* Copyright (C) 2008 Texas Instruments
	5	*
	6	* Modified from mach-omap2/board-3430sdp.c
	7	*
	8	* Initial code: Syed Mohammed Khasim
	9	*
	10	* This program is free software; you can redistribute it and/or modify
	11	* it under the terms of the GNU General Public License version 2 as
	12	* published by the Free Software Foundation.
	13	*/
	14
	15	#include <linux/kernel.h>
	16	#include <linux/init.h>
	17	#include <linux/platform_device.h>
	18	#include <linux/delay.h>
	19	#include <linux/err.h>
	20	#include <linux/clk.h>
	21	#include <linux/io.h>
	22	#include <linux/leds.h>
	23	#include <linux/gpio.h>
	24	#include <linux/input.h>
	25	#include <linux/gpio_keys.h>
8743410d	26	#include <linux/opp.h>
2885f000 SMK	27
	28	#include <linux/mtd/mtd.h>
	29	#include <linux/mtd/partitions.h>
	30	#include <linux/mtd/nand.h>
3a63833e	31	#include <linux/mmc/host.h>
2885f000	32
bb3b9d8e	33	#include <linux/regulator/machine.h>
b07682b6	34	#include <linux/i2c/twl.h>
145d9c94	35
2885f000 SMK	36	#include <mach/hardware.h>
	37	#include <asm/mach-types.h>
	38	#include <asm/mach/arch.h>
	39	#include <asm/mach/map.h>
	40	#include <asm/mach/flash.h>
	41
4e65331c	42	#include "common.h"
a0b38cc4	43	#include <video/omapdss.h>
dac8eb5f	44	#include <video/omap-panel-tfp410.h>
ce491cf8 TL	45	#include <plat/gpmc.h>
ce491cf8 TL	46	#include <plat/nand.h>
ce491cf8	47	#include <plat/usb.h>
8743410d	48	#include <plat/omap_device.h>
2885f000	49
ca5742bd	50	#include "mux.h"
d02a900b	51	#include "hsmmc.h"
8743410d	52	#include "pm.h"
fbd8071c	53	#include "common-board-devices.h"
2885f000	54
954bed04 RN	55	/*
	56	* OMAP3 Beagle revision
	57	* Run time detection of Beagle revision is done by reading GPIO.
	58	* GPIO ID -
	59	* AXBX = GPIO173, GPIO172, GPIO171: 1 1 1
	60	* C1_3 = GPIO173, GPIO172, GPIO171: 1 1 0
	61	* C4 = GPIO173, GPIO172, GPIO171: 1 0 1
5fe8b4c1 JF	62	* XMA/XMB = GPIO173, GPIO172, GPIO171: 0 0 0
5fe8b4c1 JF	63	* XMC = GPIO173, GPIO172, GPIO171: 0 1 0
954bed04 RN	64	*/
	65	enum {
	66	OMAP3BEAGLE_BOARD_UNKN = 0,
	67	OMAP3BEAGLE_BOARD_AXBX,
	68	OMAP3BEAGLE_BOARD_C1_3,
	69	OMAP3BEAGLE_BOARD_C4,
	70	OMAP3BEAGLE_BOARD_XM,
5fe8b4c1	71	OMAP3BEAGLE_BOARD_XMC,
954bed04 RN	72	};
	73
	74	static u8 omap3_beagle_version;
	75
5fe8b4c1 JF	76	/*
	77	* Board-specific configuration
	78	* Defaults to BeagleBoard-xMC
	79	*/
	80	static struct {
	81	int mmc1_gpio_wp;
	82	int usb_pwr_level;
aef2b896	83	int dvi_pd_gpio;
5fe8b4c1	84	int usr_button_gpio;
1afb82e4	85	int mmc_caps;
5fe8b4c1 JF	86	} beagle_config = {
	87	.mmc1_gpio_wp = -EINVAL,
	88	.usb_pwr_level = GPIOF_OUT_INIT_LOW,
aef2b896	89	.dvi_pd_gpio = -EINVAL,
5fe8b4c1	90	.usr_button_gpio = 4,
1afb82e4	91	.mmc_caps = MMC_CAP_4_BIT_DATA \| MMC_CAP_8_BIT_DATA,
5fe8b4c1	92	};
954bed04	93
bc593f5d IG	94	static struct gpio omap3_beagle_rev_gpios[] __initdata = {
	95	{ 171, GPIOF_IN, "rev_id_0" },
	96	{ 172, GPIOF_IN, "rev_id_1" },
	97	{ 173, GPIOF_IN, "rev_id_2" },
	98	};
	99
954bed04 RN	100	static void __init omap3_beagle_init_rev(void)
	101	{
	102	int ret;
	103	u16 beagle_rev = 0;
	104
	105	omap_mux_init_gpio(171, OMAP_PIN_INPUT_PULLUP);
	106	omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
	107	omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
	108
bc593f5d IG	109	ret = gpio_request_array(omap3_beagle_rev_gpios,
	110	ARRAY_SIZE(omap3_beagle_rev_gpios));
	111	if (ret < 0) {
	112	printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
	113	omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
	114	return;
	115	}
954bed04 RN	116
	117	beagle_rev = gpio_get_value(171) \| (gpio_get_value(172) << 1)
	118	\| (gpio_get_value(173) << 2);
	119
5e2ffc30 TK	120	gpio_free_array(omap3_beagle_rev_gpios,
	121	ARRAY_SIZE(omap3_beagle_rev_gpios));
	122
954bed04 RN	123	switch (beagle_rev) {
	124	case 7:
	125	printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
	126	omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
5fe8b4c1	127	beagle_config.mmc1_gpio_wp = 29;
aef2b896	128	beagle_config.dvi_pd_gpio = 170;
5fe8b4c1	129	beagle_config.usr_button_gpio = 7;
954bed04 RN	130	break;
	131	case 6:
	132	printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
	133	omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
5fe8b4c1	134	beagle_config.mmc1_gpio_wp = 23;
aef2b896	135	beagle_config.dvi_pd_gpio = 170;
5fe8b4c1	136	beagle_config.usr_button_gpio = 7;
954bed04 RN	137	break;
	138	case 5:
	139	printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
	140	omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
5fe8b4c1	141	beagle_config.mmc1_gpio_wp = 23;
aef2b896	142	beagle_config.dvi_pd_gpio = 170;
5fe8b4c1	143	beagle_config.usr_button_gpio = 7;
954bed04 RN	144	break;
954bed04 RN	145	case 0:
5fe8b4c1	146	printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n");
954bed04	147	omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
5fe8b4c1	148	beagle_config.usb_pwr_level = GPIOF_OUT_INIT_HIGH;
1afb82e4	149	beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
5fe8b4c1 JF	150	break;
	151	case 2:
	152	printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n");
	153	omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC;
1afb82e4	154	beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
954bed04 RN	155	break;
	156	default:
	157	printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
	158	omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
	159	}
954bed04 RN	160	}
954bed04 RN	161
2885f000 SMK	162	static struct mtd_partition omap3beagle_nand_partitions[] = {
	163	/* All the partition sizes are listed in terms of NAND block size */
	164	{
	165	.name = "X-Loader",
	166	.offset = 0,
	167	.size = 4 * NAND_BLOCK_SIZE,
	168	.mask_flags = MTD_WRITEABLE, /* force read-only */
	169	},
	170	{
	171	.name = "U-Boot",
	172	.offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
	173	.size = 15 * NAND_BLOCK_SIZE,
	174	.mask_flags = MTD_WRITEABLE, /* force read-only */
	175	},
	176	{
	177	.name = "U-Boot Env",
	178	.offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
	179	.size = 1 * NAND_BLOCK_SIZE,
	180	},
	181	{
	182	.name = "Kernel",
	183	.offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
	184	.size = 32 * NAND_BLOCK_SIZE,
	185	},
	186	{
	187	.name = "File System",
	188	.offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
	189	.size = MTDPART_SIZ_FULL,
	190	},
	191	};
	192
044d32ff KK	193	/* DSS */
044d32ff KK	194
2e6f2ee7	195	static struct tfp410_platform_data dvi_panel = {
fcca7194	196	.i2c_bus_num = 3,
e813a55e	197	.power_down_gpio = -1,
89747c91 BW	198	};
89747c91 BW	199
044d32ff KK	200	static struct omap_dss_device beagle_dvi_device = {
	201	.type = OMAP_DISPLAY_TYPE_DPI,
	202	.name = "dvi",
2e6f2ee7	203	.driver_name = "tfp410",
89747c91	204	.data = &dvi_panel,
044d32ff	205	.phy.dpi.data_lines = 24,
044d32ff KK	206	};
	207
	208	static struct omap_dss_device beagle_tv_device = {
	209	.name = "tv",
	210	.driver_name = "venc",
	211	.type = OMAP_DISPLAY_TYPE_VENC,
	212	.phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
	213	};
	214
	215	static struct omap_dss_device *beagle_dss_devices[] = {
	216	&beagle_dvi_device,
	217	&beagle_tv_device,
	218	};
	219
	220	static struct omap_dss_board_info beagle_dss_data = {
	221	.num_devices = ARRAY_SIZE(beagle_dss_devices),
	222	.devices = beagle_dss_devices,
	223	.default_device = &beagle_dvi_device,
	224	};
	225
2e12bd7e PW	226	#include "sdram-micron-mt46h32m32lf-6.h"
2e12bd7e PW	227
68ff0423	228	static struct omap2_hsmmc_info mmc[] = {
90c62bf0 TL	229	{
90c62bf0 TL	230	.mmc = 1,
1afb82e4	231	.caps = MMC_CAP_4_BIT_DATA,
5fe8b4c1	232	.gpio_wp = -EINVAL,
3b972bf0	233	.deferred = true,
90c62bf0 TL	234	},
	235	{} /* Terminator */
	236	};
	237
786b01a8 OD	238	static struct regulator_consumer_supply beagle_vmmc1_supply[] = {
786b01a8 OD	239	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
bb3b9d8e DB	240	};
bb3b9d8e DB	241
786b01a8 OD	242	static struct regulator_consumer_supply beagle_vsim_supply[] = {
786b01a8 OD	243	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
bb3b9d8e DB	244	};
bb3b9d8e DB	245
90c62bf0 TL	246	static struct gpio_led gpio_leds[];
	247
	248	static int beagle_twl_gpio_setup(struct device *dev,
	249	unsigned gpio, unsigned ngpio)
	250	{
5fe8b4c1 JF	251	int r;
5fe8b4c1 JF	252
5fe8b4c1	253	mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp;
90c62bf0	254	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
145d9c94	255	mmc[0].gpio_cd = gpio + 0;
3b972bf0	256	omap_hsmmc_late_init(mmc);
90c62bf0	257
68fc3e15 KK	258	/*
	259	* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
	260	* high / others active low)
bc593f5d	261	* DVI reset GPIO is different between beagle revisions
1bd9ef19	262	*/
5fe8b4c1 JF	263	/* Valid for all -xM revisions */
5fe8b4c1 JF	264	if (cpu_is_omap3630()) {
bc593f5d IG	265	/*
	266	* gpio + 1 on Xm controls the TFP410's enable line (active low)
	267	* gpio + 2 control varies depending on the board rev as below:
	268	* P7/P8 revisions(prototype): Camera EN
	269	* A2+ revisions (production): LDO (DVI, serial, led blocks)
	270	*/
	271	r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW,
	272	"nDVI_PWR_EN");
1bd9ef19 KK	273	if (r)
	274	pr_err("%s: unable to configure nDVI_PWR_EN\n",
	275	__func__);
aef2b896 RD	276
	277	beagle_config.dvi_pd_gpio = gpio + 2;
	278
bc593f5d	279	} else {
bc593f5d IG	280	/*
	281	* REVISIT: need ehci-omap hooks for external VBUS
	282	* power switch and overcurrent detect
	283	*/
	284	if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
	285	pr_err("%s: unable to configure EHCI_nOC\n", __func__);
1bd9ef19	286	}
aef2b896	287	dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio;
1bd9ef19	288
5fe8b4c1 JF	289	gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
5fe8b4c1 JF	290	"nEN_USB_PWR");
bc593f5d IG	291
	292	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
	293	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
	294
90c62bf0 TL	295	return 0;
	296	}
	297
	298	static struct twl4030_gpio_platform_data beagle_gpio_data = {
90c62bf0 TL	299	.use_leds = true,
	300	.pullups = BIT(1),
	301	.pulldowns = BIT(2) \| BIT(6) \| BIT(7) \| BIT(8) \| BIT(13)
	302	\| BIT(15) \| BIT(16) \| BIT(17),
	303	.setup = beagle_twl_gpio_setup,
	304	};
	305
bb3b9d8e DB	306	/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
	307	static struct regulator_init_data beagle_vmmc1 = {
	308	.constraints = {
	309	.min_uV = 1850000,
	310	.max_uV = 3150000,
	311	.valid_modes_mask = REGULATOR_MODE_NORMAL
	312	\| REGULATOR_MODE_STANDBY,
	313	.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
	314	\| REGULATOR_CHANGE_MODE
	315	\| REGULATOR_CHANGE_STATUS,
	316	},
786b01a8 OD	317	.num_consumer_supplies = ARRAY_SIZE(beagle_vmmc1_supply),
786b01a8 OD	318	.consumer_supplies = beagle_vmmc1_supply,
bb3b9d8e DB	319	};
	320
	321	/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
	322	static struct regulator_init_data beagle_vsim = {
	323	.constraints = {
	324	.min_uV = 1800000,
	325	.max_uV = 3000000,
	326	.valid_modes_mask = REGULATOR_MODE_NORMAL
	327	\| REGULATOR_MODE_STANDBY,
	328	.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
	329	\| REGULATOR_CHANGE_MODE
	330	\| REGULATOR_CHANGE_STATUS,
	331	},
786b01a8 OD	332	.num_consumer_supplies = ARRAY_SIZE(beagle_vsim_supply),
786b01a8 OD	333	.consumer_supplies = beagle_vsim_supply,
bb3b9d8e DB	334	};
bb3b9d8e DB	335
90c62bf0	336	static struct twl4030_platform_data beagle_twldata = {
90c62bf0 TL	337	/* platform_data for children goes here */
90c62bf0 TL	338	.gpio = &beagle_gpio_data,
bb3b9d8e DB	339	.vmmc1 = &beagle_vmmc1,
bb3b9d8e DB	340	.vsim = &beagle_vsim,
90c62bf0 TL	341	};
90c62bf0 TL	342
e3333f48 MP	343	static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
	344	{
	345	I2C_BOARD_INFO("eeprom", 0x50),
	346	},
	347	};
	348
90c62bf0 TL	349	static int __init omap3_beagle_i2c_init(void)
90c62bf0 TL	350	{
827ed9ae	351	omap3_pmic_get_config(&beagle_twldata,
cdcc966d KM	352	TWL_COMMON_PDATA_USB \| TWL_COMMON_PDATA_MADC \|
cdcc966d KM	353	TWL_COMMON_PDATA_AUDIO,
b252b0ef PU	354	TWL_COMMON_REGULATOR_VDAC \| TWL_COMMON_REGULATOR_VPLL2);
	355
	356	beagle_twldata.vpll2->constraints.name = "VDVI";
	357
fbd8071c	358	omap3_pmic_init("twl4030", &beagle_twldata);
8ca7fe26 KK	359	/* Bus 3 is attached to the DVI port where devices like the pico DLP
8ca7fe26 KK	360	* projector don't work reliably with 400kHz */
e3333f48	361	omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
90c62bf0 TL	362	return 0;
	363	}
	364
2885f000 SMK	365	static struct gpio_led gpio_leds[] = {
	366	{
	367	.name = "beagleboard::usr0",
	368	.default_trigger = "heartbeat",
	369	.gpio = 150,
	370	},
	371	{
	372	.name = "beagleboard::usr1",
	373	.default_trigger = "mmc0",
	374	.gpio = 149,
	375	},
90c62bf0 TL	376	{
	377	.name = "beagleboard::pmu_stat",
	378	.gpio = -EINVAL, /* gets replaced */
	379	.active_low = true,
	380	},
2885f000 SMK	381	};
	382
	383	static struct gpio_led_platform_data gpio_led_info = {
	384	.leds = gpio_leds,
	385	.num_leds = ARRAY_SIZE(gpio_leds),
	386	};
	387
	388	static struct platform_device leds_gpio = {
	389	.name = "leds-gpio",
	390	.id = -1,
	391	.dev = {
	392	.platform_data = &gpio_led_info,
	393	},
	394	};
	395
	396	static struct gpio_keys_button gpio_buttons[] = {
	397	{
	398	.code = BTN_EXTRA,
5fe8b4c1 JF	399	/* Dynamically assigned depending on board */
5fe8b4c1 JF	400	.gpio = -EINVAL,
2885f000 SMK	401	.desc = "user",
	402	.wakeup = 1,
	403	},
	404	};
	405
	406	static struct gpio_keys_platform_data gpio_key_info = {
	407	.buttons = gpio_buttons,
	408	.nbuttons = ARRAY_SIZE(gpio_buttons),
	409	};
	410
	411	static struct platform_device keys_gpio = {
	412	.name = "gpio-keys",
	413	.id = -1,
	414	.dev = {
	415	.platform_data = &gpio_key_info,
	416	},
	417	};
	418
cdcc966d KM	419	static struct platform_device madc_hwmon = {
	420	.name = "twl4030_madc_hwmon",
	421	.id = -1,
	422	};
	423
2885f000	424	static struct platform_device *omap3_beagle_devices[] __initdata = {
2885f000 SMK	425	&leds_gpio,
2885f000 SMK	426	&keys_gpio,
cdcc966d	427	&madc_hwmon,
2885f000 SMK	428	};
2885f000 SMK	429
181b250c	430	static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
58a5491c	431
f6f6c9a5	432	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
181b250c KM	433	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
181b250c KM	434	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
58a5491c FB	435
	436	.phy_reset = true,
	437	.reset_gpio_port[0] = -EINVAL,
	438	.reset_gpio_port[1] = 147,
	439	.reset_gpio_port[2] = -EINVAL
	440	};
	441
ca5742bd TL	442	#ifdef CONFIG_OMAP_MUX
	443	static struct omap_board_mux board_mux[] __initdata = {
	444	{ .reg_offset = OMAP_MUX_TERMINATOR },
	445	};
ca5742bd TL	446	#endif
ca5742bd TL	447
8743410d NM	448	static void __init beagle_opp_init(void)
	449	{
	450	int r = 0;
	451
	452	/* Initialize the omap3 opp table */
	453	if (omap3_opp_init()) {
	454	pr_err("%s: opp default init failed\n", __func__);
	455	return;
	456	}
	457
5fe8b4c1 JF	458	/* Custom OPP enabled for all xM versions */
5fe8b4c1 JF	459	if (cpu_is_omap3630()) {
8c7f6594	460	struct device mpu_dev, iva_dev;
8743410d	461
b1621fc8 BC	462	mpu_dev = omap_device_get_by_hwmod_name("mpu");
b1621fc8 BC	463	iva_dev = omap_device_get_by_hwmod_name("iva");
8c7f6594 KH	464
8c7f6594 KH	465	if (!mpu_dev \|\| !iva_dev) {
8743410d	466	pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
8c7f6594	467	__func__, mpu_dev, iva_dev);
8743410d NM	468	return;
	469	}
	470	/* Enable MPU 1GHz and lower opps */
8c7f6594	471	r = opp_enable(mpu_dev, 800000000);
8743410d NM	472	/* TODO: MPU 1GHz needs SR and ABB */
	473
	474	/* Enable IVA 800MHz and lower opps */
8c7f6594	475	r \|= opp_enable(iva_dev, 660000000);
8743410d NM	476	/* TODO: DSP 800MHz needs SR and ABB */
	477	if (r) {
	478	pr_err("%s: failed to enable higher opp %d\n",
	479	__func__, r);
	480	/*
	481	* Cleanup - disable the higher freqs - we dont care
	482	* about the results
	483	*/
8c7f6594 KH	484	opp_disable(mpu_dev, 800000000);
8c7f6594 KH	485	opp_disable(iva_dev, 660000000);
8743410d NM	486	}
	487	}
	488	return;
	489	}
	490
2885f000 SMK	491	static void __init omap3_beagle_init(void)
2885f000 SMK	492	{
ca5742bd	493	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
954bed04	494	omap3_beagle_init_rev();
d1589f09	495
aef2b896	496	if (gpio_is_valid(beagle_config.mmc1_gpio_wp))
d1589f09	497	omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
1afb82e4	498	mmc[0].caps = beagle_config.mmc_caps;
3b972bf0	499	omap_hsmmc_init(mmc);
d1589f09	500
90c62bf0	501	omap3_beagle_i2c_init();
5fe8b4c1 JF	502
	503	gpio_buttons[0].gpio = beagle_config.usr_button_gpio;
	504
2885f000 SMK	505	platform_add_devices(omap3_beagle_devices,
2885f000 SMK	506	ARRAY_SIZE(omap3_beagle_devices));
aef2b896 RD	507	if (gpio_is_valid(beagle_config.dvi_pd_gpio))
aef2b896 RD	508	omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT);
d5e13227	509	omap_display_init(&beagle_dss_data);
2885f000	510	omap_serial_init();
a4ca9dbe TL	511	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
a4ca9dbe TL	512	mt46h32m32lf6_sdrc_params);
90c62bf0	513
9e18630b	514	usb_musb_init(NULL);
9e64bb1e	515	usbhs_init(&usbhs_bdata);
9a3f39ff MR	516	omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
9a3f39ff MR	517	ARRAY_SIZE(omap3beagle_nand_partitions));
9fb97412	518
e2a346a2 AH	519	/* Ensure msecure is mux'd to be able to set the RTC. */
	520	omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
	521
9fb97412	522	/* Ensure SDRC pins are mux'd for self-refresh */
4896e394 TL	523	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
4896e394 TL	524	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
044d32ff	525
8743410d	526	beagle_opp_init();
2885f000 SMK	527	}
2885f000 SMK	528
2885f000 SMK	529	MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
2885f000 SMK	530	/* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
5e52b435	531	.atag_offset = 0x100,
71ee7dad	532	.reserve = omap_reserve,
3dc3bad6	533	.map_io = omap3_map_io,
7b250aff	534	.init_early = omap3_init_early,
be732460	535	.init_irq = omap3_init_irq,
6b2f55d7	536	.handle_irq = omap3_intc_handle_irq,
2885f000	537	.init_machine = omap3_beagle_init,
bbd707ac	538	.init_late = omap3_init_late,
e74984e4	539	.timer = &omap3_secure_timer,
baa95883	540	.restart = omap_prcm_restart,
2885f000	541	MACHINE_END