Commit | Line | Data |
---|---|---|
555a3656 | 1 | /* |
9dd0b194 | 2 | * arch/arm/mach-orion5x/dns323-setup.c |
555a3656 HVR |
3 | * |
4 | * Copyright (C) 2007 Herbert Valerio Riedel <hvr@gnu.org> | |
5 | * | |
6 | * This program is free software; you can redistribute it and/or modify | |
7 | * it under the terms of the GNU Lesser General Public License as | |
8 | * published by the Free Software Foundation; either version 2 of the | |
9 | * License, or (at your option) any later version. | |
10 | * | |
11 | */ | |
12 | ||
13 | #include <linux/kernel.h> | |
14 | #include <linux/init.h> | |
15 | #include <linux/platform_device.h> | |
16 | #include <linux/pci.h> | |
17 | #include <linux/irq.h> | |
18 | #include <linux/mtd/physmap.h> | |
19 | #include <linux/mv643xx_eth.h> | |
20 | #include <linux/leds.h> | |
21 | #include <linux/gpio_keys.h> | |
22 | #include <linux/input.h> | |
23 | #include <linux/i2c.h> | |
24 | #include <asm/mach-types.h> | |
25 | #include <asm/gpio.h> | |
26 | #include <asm/mach/arch.h> | |
27 | #include <asm/mach/pci.h> | |
9dd0b194 | 28 | #include <asm/arch/orion5x.h> |
555a3656 HVR |
29 | #include "common.h" |
30 | ||
31 | #define DNS323_GPIO_LED_RIGHT_AMBER 1 | |
32 | #define DNS323_GPIO_LED_LEFT_AMBER 2 | |
33 | #define DNS323_GPIO_LED_POWER 5 | |
34 | #define DNS323_GPIO_OVERTEMP 6 | |
35 | #define DNS323_GPIO_RTC 7 | |
36 | #define DNS323_GPIO_POWER_OFF 8 | |
37 | #define DNS323_GPIO_KEY_POWER 9 | |
38 | #define DNS323_GPIO_KEY_RESET 10 | |
39 | ||
40 | /**************************************************************************** | |
41 | * PCI setup | |
42 | */ | |
43 | ||
44 | static int __init dns323_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) | |
45 | { | |
92b913b0 | 46 | int irq; |
555a3656 | 47 | |
92b913b0 LB |
48 | /* |
49 | * Check for devices with hard-wired IRQs. | |
50 | */ | |
51 | irq = orion5x_pci_map_irq(dev, slot, pin); | |
52 | if (irq != -1) | |
53 | return irq; | |
54 | ||
55 | pr_err("%s: requested mapping for unknown device\n", __func__); | |
555a3656 HVR |
56 | |
57 | return -1; | |
58 | } | |
59 | ||
60 | static struct hw_pci dns323_pci __initdata = { | |
bbdf1c1e | 61 | .nr_controllers = 2, |
555a3656 | 62 | .swizzle = pci_std_swizzle, |
9dd0b194 LB |
63 | .setup = orion5x_pci_sys_setup, |
64 | .scan = orion5x_pci_sys_scan_bus, | |
555a3656 HVR |
65 | .map_irq = dns323_pci_map_irq, |
66 | }; | |
67 | ||
68 | static int __init dns323_pci_init(void) | |
69 | { | |
70 | if (machine_is_dns323()) | |
71 | pci_common_init(&dns323_pci); | |
72 | ||
73 | return 0; | |
74 | } | |
75 | ||
76 | subsys_initcall(dns323_pci_init); | |
77 | ||
78 | /**************************************************************************** | |
79 | * Ethernet | |
80 | */ | |
81 | ||
82 | static struct mv643xx_eth_platform_data dns323_eth_data = { | |
83 | .phy_addr = 8, | |
84 | .force_phy_addr = 1, | |
85 | }; | |
86 | ||
87 | /**************************************************************************** | |
88 | * 8MiB NOR flash (Spansion S29GL064M90TFIR4) | |
89 | * | |
90 | * Layout as used by D-Link: | |
91 | * 0x00000000-0x00010000 : "MTD1" | |
92 | * 0x00010000-0x00020000 : "MTD2" | |
93 | * 0x00020000-0x001a0000 : "Linux Kernel" | |
94 | * 0x001a0000-0x007d0000 : "File System" | |
95 | * 0x007d0000-0x00800000 : "u-boot" | |
96 | */ | |
97 | ||
98 | #define DNS323_NOR_BOOT_BASE 0xf4000000 | |
99 | #define DNS323_NOR_BOOT_SIZE SZ_8M | |
100 | ||
101 | static struct mtd_partition dns323_partitions[] = { | |
102 | { | |
103 | .name = "MTD1", | |
104 | .size = 0x00010000, | |
105 | .offset = 0, | |
106 | }, { | |
107 | .name = "MTD2", | |
108 | .size = 0x00010000, | |
109 | .offset = 0x00010000, | |
110 | }, { | |
111 | .name = "Linux Kernel", | |
112 | .size = 0x00180000, | |
113 | .offset = 0x00020000, | |
114 | }, { | |
115 | .name = "File System", | |
116 | .size = 0x00630000, | |
117 | .offset = 0x001A0000, | |
118 | }, { | |
119 | .name = "u-boot", | |
120 | .size = 0x00030000, | |
121 | .offset = 0x007d0000, | |
e7068ad3 | 122 | }, |
555a3656 HVR |
123 | }; |
124 | ||
125 | static struct physmap_flash_data dns323_nor_flash_data = { | |
126 | .width = 1, | |
127 | .parts = dns323_partitions, | |
128 | .nr_parts = ARRAY_SIZE(dns323_partitions) | |
129 | }; | |
130 | ||
131 | static struct resource dns323_nor_flash_resource = { | |
132 | .flags = IORESOURCE_MEM, | |
133 | .start = DNS323_NOR_BOOT_BASE, | |
134 | .end = DNS323_NOR_BOOT_BASE + DNS323_NOR_BOOT_SIZE - 1, | |
135 | }; | |
136 | ||
137 | static struct platform_device dns323_nor_flash = { | |
138 | .name = "physmap-flash", | |
139 | .id = 0, | |
e7068ad3 LB |
140 | .dev = { |
141 | .platform_data = &dns323_nor_flash_data, | |
142 | }, | |
555a3656 HVR |
143 | .resource = &dns323_nor_flash_resource, |
144 | .num_resources = 1, | |
145 | }; | |
146 | ||
147 | /**************************************************************************** | |
148 | * GPIO LEDs (simple - doesn't use hardware blinking support) | |
149 | */ | |
150 | ||
151 | static struct gpio_led dns323_leds[] = { | |
152 | { | |
153 | .name = "power:blue", | |
154 | .gpio = DNS323_GPIO_LED_POWER, | |
155 | .active_low = 1, | |
156 | }, { | |
157 | .name = "right:amber", | |
158 | .gpio = DNS323_GPIO_LED_RIGHT_AMBER, | |
159 | .active_low = 1, | |
160 | }, { | |
161 | .name = "left:amber", | |
162 | .gpio = DNS323_GPIO_LED_LEFT_AMBER, | |
163 | .active_low = 1, | |
164 | }, | |
165 | }; | |
166 | ||
167 | static struct gpio_led_platform_data dns323_led_data = { | |
168 | .num_leds = ARRAY_SIZE(dns323_leds), | |
169 | .leds = dns323_leds, | |
170 | }; | |
171 | ||
172 | static struct platform_device dns323_gpio_leds = { | |
173 | .name = "leds-gpio", | |
174 | .id = -1, | |
e7068ad3 LB |
175 | .dev = { |
176 | .platform_data = &dns323_led_data, | |
177 | }, | |
555a3656 HVR |
178 | }; |
179 | ||
180 | /**************************************************************************** | |
181 | * GPIO Attached Keys | |
182 | */ | |
183 | ||
184 | static struct gpio_keys_button dns323_buttons[] = { | |
185 | { | |
186 | .code = KEY_RESTART, | |
187 | .gpio = DNS323_GPIO_KEY_RESET, | |
188 | .desc = "Reset Button", | |
189 | .active_low = 1, | |
e7068ad3 | 190 | }, { |
555a3656 HVR |
191 | .code = KEY_POWER, |
192 | .gpio = DNS323_GPIO_KEY_POWER, | |
193 | .desc = "Power Button", | |
194 | .active_low = 1, | |
e7068ad3 | 195 | }, |
555a3656 HVR |
196 | }; |
197 | ||
198 | static struct gpio_keys_platform_data dns323_button_data = { | |
199 | .buttons = dns323_buttons, | |
e7068ad3 | 200 | .nbuttons = ARRAY_SIZE(dns323_buttons), |
555a3656 HVR |
201 | }; |
202 | ||
203 | static struct platform_device dns323_button_device = { | |
204 | .name = "gpio-keys", | |
205 | .id = -1, | |
206 | .num_resources = 0, | |
e7068ad3 LB |
207 | .dev = { |
208 | .platform_data = &dns323_button_data, | |
209 | }, | |
555a3656 HVR |
210 | }; |
211 | ||
212 | /**************************************************************************** | |
213 | * General Setup | |
214 | */ | |
215 | ||
216 | static struct platform_device *dns323_plat_devices[] __initdata = { | |
217 | &dns323_nor_flash, | |
218 | &dns323_gpio_leds, | |
219 | &dns323_button_device, | |
220 | }; | |
221 | ||
222 | /* | |
223 | * On the DNS-323 the following devices are attached via I2C: | |
224 | * | |
225 | * i2c addr | chip | description | |
226 | * 0x3e | GMT G760Af | fan speed PWM controller | |
227 | * 0x48 | GMT G751-2f | temp. sensor and therm. watchdog (LM75 compatible) | |
228 | * 0x68 | ST M41T80 | RTC w/ alarm | |
229 | */ | |
230 | static struct i2c_board_info __initdata dns323_i2c_devices[] = { | |
231 | { | |
232 | I2C_BOARD_INFO("g760a", 0x3e), | |
555a3656 HVR |
233 | #if 0 |
234 | /* this entry requires the new-style driver model lm75 driver, | |
235 | * for the meantime "insmod lm75.ko force_lm75=0,0x48" is needed */ | |
e7068ad3 | 236 | }, { |
3760f736 | 237 | I2C_BOARD_INFO("g751", 0x48), |
555a3656 | 238 | #endif |
e7068ad3 | 239 | }, { |
3760f736 | 240 | I2C_BOARD_INFO("m41t80", 0x68), |
e7068ad3 | 241 | }, |
555a3656 HVR |
242 | }; |
243 | ||
244 | /* DNS-323 specific power off method */ | |
245 | static void dns323_power_off(void) | |
246 | { | |
247 | pr_info("%s: triggering power-off...\n", __func__); | |
248 | gpio_set_value(DNS323_GPIO_POWER_OFF, 1); | |
249 | } | |
250 | ||
251 | static void __init dns323_init(void) | |
252 | { | |
253 | /* Setup basic Orion functions. Need to be called early. */ | |
9dd0b194 | 254 | orion5x_init(); |
555a3656 HVR |
255 | |
256 | /* setup flash mapping | |
257 | * CS3 holds a 8 MB Spansion S29GL064M90TFIR4 | |
258 | */ | |
9dd0b194 | 259 | orion5x_setup_dev_boot_win(DNS323_NOR_BOOT_BASE, DNS323_NOR_BOOT_SIZE); |
555a3656 | 260 | |
b46926bb | 261 | /* DNS-323 has a Marvell 88X7042 SATA controller attached via PCIe |
555a3656 | 262 | * |
b46926bb | 263 | * Open a special address decode windows for the PCIe WA. |
555a3656 | 264 | */ |
9dd0b194 LB |
265 | orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE, |
266 | ORION5X_PCIE_WA_SIZE); | |
555a3656 HVR |
267 | |
268 | /* set MPP to 0 as D-Link's 2.6.12.6 kernel did */ | |
9dd0b194 LB |
269 | orion5x_write(MPP_0_7_CTRL, 0); |
270 | orion5x_write(MPP_8_15_CTRL, 0); | |
271 | orion5x_write(MPP_16_19_CTRL, 0); | |
272 | orion5x_write(MPP_DEV_CTRL, 0); | |
555a3656 HVR |
273 | |
274 | /* Define used GPIO pins | |
275 | ||
276 | GPIO Map: | |
277 | ||
278 | | 0 | | PEX_RST_OUT (not controlled by GPIO) | |
279 | | 1 | Out | right amber LED (= sata ch0 LED) (low-active) | |
280 | | 2 | Out | left amber LED (= sata ch1 LED) (low-active) | |
281 | | 3 | Out | //unknown// | |
282 | | 4 | Out | power button LED (low-active, together with pin #5) | |
283 | | 5 | Out | power button LED (low-active, together with pin #4) | |
284 | | 6 | In | GMT G751-2f overtemp. shutdown signal (low-active) | |
285 | | 7 | In | M41T80 nIRQ/OUT/SQW signal | |
286 | | 8 | Out | triggers power off (high-active) | |
287 | | 9 | In | power button switch (low-active) | |
288 | | 10 | In | reset button switch (low-active) | |
289 | | 11 | Out | //unknown// | |
290 | | 12 | Out | //unknown// | |
291 | | 13 | Out | //unknown// | |
292 | | 14 | Out | //unknown// | |
293 | | 15 | Out | //unknown// | |
294 | */ | |
9dd0b194 | 295 | orion5x_gpio_set_valid_pins(0x07f6); |
555a3656 HVR |
296 | |
297 | /* register dns323 specific power-off method */ | |
e7068ad3 LB |
298 | if (gpio_request(DNS323_GPIO_POWER_OFF, "POWEROFF") != 0 || |
299 | gpio_direction_output(DNS323_GPIO_POWER_OFF, 0) != 0) | |
555a3656 HVR |
300 | pr_err("DNS323: failed to setup power-off GPIO\n"); |
301 | ||
302 | pm_power_off = dns323_power_off; | |
303 | ||
304 | /* register flash and other platform devices */ | |
305 | platform_add_devices(dns323_plat_devices, | |
306 | ARRAY_SIZE(dns323_plat_devices)); | |
307 | ||
308 | i2c_register_board_info(0, dns323_i2c_devices, | |
309 | ARRAY_SIZE(dns323_i2c_devices)); | |
310 | ||
9dd0b194 | 311 | orion5x_eth_init(&dns323_eth_data); |
555a3656 HVR |
312 | } |
313 | ||
314 | /* Warning: D-Link uses a wrong mach-type (=526) in their bootloader */ | |
315 | MACHINE_START(DNS323, "D-Link DNS-323") | |
316 | /* Maintainer: Herbert Valerio Riedel <hvr@gnu.org> */ | |
9dd0b194 LB |
317 | .phys_io = ORION5X_REGS_PHYS_BASE, |
318 | .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, | |
555a3656 HVR |
319 | .boot_params = 0x00000100, |
320 | .init_machine = dns323_init, | |
9dd0b194 LB |
321 | .map_io = orion5x_map_io, |
322 | .init_irq = orion5x_init_irq, | |
323 | .timer = &orion5x_timer, | |
be73a347 | 324 | .fixup = tag_fixup_mem32, |
555a3656 | 325 | MACHINE_END |