[deliverable/linux.git] / arch / arm / mach-orion5x / edmini_v2-setup.c

/*
 * arch/arm/mach-orion5x/edmini_v2-setup.c
 *
 * LaCie Ethernet Disk mini V2 Setup
 *
 * Copyright (C) 2008 Christopher Moore <moore@free.fr>
 * Copyright (C) 2008 Albert Aribaud <albert.aribaud@free.fr>
 *
 * This file is licensed under the terms of the GNU General Public
 * License version 2. This program is licensed "as is" without any
 * warranty of any kind, whether express or implied.
 */

/*
 * TODO: add Orion USB device port init when kernel.org support is added.
 * TODO: add flash write support: see below.
 * TODO: add power-off support.
 * TODO: add I2C EEPROM support.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/pci.h>
#include <linux/irq.h>
#include <linux/mtd/physmap.h>
#include <linux/mv643xx_eth.h>
#include <linux/leds.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/i2c.h>
#include <linux/ata_platform.h>
#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"

/*****************************************************************************
 * EDMINI_V2 Info
 ****************************************************************************/

/*
 * 512KB NOR flash Device bus boot chip select
 */

#define EDMINI_V2_NOR_BOOT_BASE		0xfff80000
#define EDMINI_V2_NOR_BOOT_SIZE		SZ_512K

/*****************************************************************************
 * 512KB NOR Flash on BOOT Device
 ****************************************************************************/

/*
 * Currently the MTD code does not recognize the MX29LV400CBCT as a bottom
 * -type device. This could cause risks of accidentally erasing critical
 * flash sectors. We thus define a single, write-protected partition covering
 * the whole flash.
 * TODO: once the flash part TOP/BOTTOM detection issue is sorted out in the MTD
 * code, break this into at least three partitions: 'u-boot code', 'u-boot
 * environment' and 'whatever is left'.
 */

static struct mtd_partition edmini_v2_partitions[] = {
	{
		.name		= "Full512kb",
		.size		= 0x00080000,
		.offset		= 0x00000000,
		.mask_flags	= MTD_WRITEABLE,
	},
};

static struct physmap_flash_data edmini_v2_nor_flash_data = {
	.width		= 1,
	.parts		= edmini_v2_partitions,
	.nr_parts	= ARRAY_SIZE(edmini_v2_partitions),
};

static struct resource edmini_v2_nor_flash_resource = {
	.flags			= IORESOURCE_MEM,
	.start			= EDMINI_V2_NOR_BOOT_BASE,
	.end			= EDMINI_V2_NOR_BOOT_BASE
		+ EDMINI_V2_NOR_BOOT_SIZE - 1,
};

static struct platform_device edmini_v2_nor_flash = {
	.name			= "physmap-flash",
	.id			= 0,
	.dev		= {
		.platform_data	= &edmini_v2_nor_flash_data,
	},
	.num_resources		= 1,
	.resource		= &edmini_v2_nor_flash_resource,
};

/*****************************************************************************
 * Ethernet
 ****************************************************************************/

static struct mv643xx_eth_platform_data edmini_v2_eth_data = {
	.phy_addr	= 8,
};

/*****************************************************************************
 * RTC 5C372a on I2C bus
 ****************************************************************************/

#define EDMINIV2_RTC_GPIO	3

static struct i2c_board_info __initdata edmini_v2_i2c_rtc = {
	I2C_BOARD_INFO("rs5c372a", 0x32),
	.irq = 0,
};

/*****************************************************************************
 * Sata
 ****************************************************************************/

static struct mv_sata_platform_data edmini_v2_sata_data = {
	.n_ports	= 2,
};

/*****************************************************************************
 * GPIO LED (simple - doesn't use hardware blinking support)
 ****************************************************************************/

#define EDMINI_V2_GPIO_LED_POWER	16

static struct gpio_led edmini_v2_leds[] = {
	{
		.name = "power:blue",
		.gpio = EDMINI_V2_GPIO_LED_POWER,
		.active_low = 1,
	},
};

static struct gpio_led_platform_data edmini_v2_led_data = {
	.num_leds = ARRAY_SIZE(edmini_v2_leds),
	.leds = edmini_v2_leds,
};

static struct platform_device edmini_v2_gpio_leds = {
	.name           = "leds-gpio",
	.id             = -1,
	.dev            = {
		.platform_data  = &edmini_v2_led_data,
	},
};

/****************************************************************************
 * GPIO key
 ****************************************************************************/

#define EDMINI_V2_GPIO_KEY_POWER	18

static struct gpio_keys_button edmini_v2_buttons[] = {
	{
		.code		= KEY_POWER,
		.gpio		= EDMINI_V2_GPIO_KEY_POWER,
		.desc		= "Power Button",
		.active_low	= 0,
	},
};

static struct gpio_keys_platform_data edmini_v2_button_data = {
	.buttons	= edmini_v2_buttons,
	.nbuttons	= ARRAY_SIZE(edmini_v2_buttons),
};

static struct platform_device edmini_v2_gpio_buttons = {
	.name		= "gpio-keys",
	.id		= -1,
	.dev		= {
		.platform_data	= &edmini_v2_button_data,
	},
};

/*****************************************************************************
 * General Setup
 ****************************************************************************/
static unsigned int edminiv2_mpp_modes[] __initdata = {
	MPP0_UNUSED,
	MPP1_UNUSED,
	MPP2_UNUSED,
	MPP3_GPIO,	/* RTC interrupt */
	MPP4_UNUSED,
	MPP5_UNUSED,
	MPP6_UNUSED,
	MPP7_UNUSED,
	MPP8_UNUSED,
	MPP9_UNUSED,
	MPP10_UNUSED,
	MPP11_UNUSED,
	MPP12_SATA_LED,	/* SATA 0 presence */
	MPP13_SATA_LED,	/* SATA 1 presence */
	MPP14_SATA_LED,	/* SATA 0 active */
	MPP15_SATA_LED,	/* SATA 1 active */
	/* 16: Power LED control (0 = On, 1 = Off) */
	MPP16_GPIO,
	/* 17: Power LED control select (0 = CPLD, 1 = GPIO16) */
	MPP17_GPIO,
	/* 18: Power button status (0 = Released, 1 = Pressed) */
	MPP18_GPIO,
	MPP19_UNUSED,
	0,
};

static void __init edmini_v2_init(void)
{
	/*
	 * Setup basic Orion functions. Need to be called early.
	 */
	orion5x_init();

	orion5x_mpp_conf(edminiv2_mpp_modes);

	/*
	 * Configure peripherals.
	 */
	orion5x_ehci0_init();
	orion5x_eth_init(&edmini_v2_eth_data);
	orion5x_i2c_init();
	orion5x_sata_init(&edmini_v2_sata_data);
	orion5x_uart0_init();

	orion5x_setup_dev_boot_win(EDMINI_V2_NOR_BOOT_BASE,
				EDMINI_V2_NOR_BOOT_SIZE);
	platform_device_register(&edmini_v2_nor_flash);
	platform_device_register(&edmini_v2_gpio_leds);
	platform_device_register(&edmini_v2_gpio_buttons);

	pr_notice("edmini_v2: USB device port, flash write and power-off "
		  "are not yet supported.\n");

	/* Get RTC IRQ and register the chip */
	if (gpio_request(EDMINIV2_RTC_GPIO, "rtc") == 0) {
		if (gpio_direction_input(EDMINIV2_RTC_GPIO) == 0)
			edmini_v2_i2c_rtc.irq = gpio_to_irq(EDMINIV2_RTC_GPIO);
		else
			gpio_free(EDMINIV2_RTC_GPIO);
	}

	if (edmini_v2_i2c_rtc.irq == 0)
		pr_warning("edmini_v2: failed to get RTC IRQ\n");

	i2c_register_board_info(0, &edmini_v2_i2c_rtc, 1);
}

/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
MACHINE_START(EDMINI_V2, "LaCie Ethernet Disk mini V2")
	/* Maintainer: Christopher Moore <moore@free.fr> */
	.atag_offset	= 0x100,
	.init_machine	= edmini_v2_init,
	.map_io		= orion5x_map_io,
	.init_early	= orion5x_init_early,
	.init_irq	= orion5x_init_irq,
	.timer		= &orion5x_timer,
	.fixup		= tag_fixup_mem32,
	.restart	= orion5x_restart,
MACHINE_END
Commit	Line	Data
0eb66974 CM	1	/*
	2	* arch/arm/mach-orion5x/edmini_v2-setup.c
	3	*
	4	* LaCie Ethernet Disk mini V2 Setup
	5	*
	6	* Copyright (C) 2008 Christopher Moore <moore@free.fr>
	7	* Copyright (C) 2008 Albert Aribaud <albert.aribaud@free.fr>
	8	*
	9	* This file is licensed under the terms of the GNU General Public
	10	* License version 2. This program is licensed "as is" without any
	11	* warranty of any kind, whether express or implied.
	12	*/
	13
	14	/*
	15	* TODO: add Orion USB device port init when kernel.org support is added.
	16	* TODO: add flash write support: see below.
	17	* TODO: add power-off support.
	18	* TODO: add I2C EEPROM support.
	19	*/
	20
	21	#include <linux/kernel.h>
	22	#include <linux/init.h>
	23	#include <linux/platform_device.h>
	24	#include <linux/pci.h>
	25	#include <linux/irq.h>
	26	#include <linux/mtd/physmap.h>
	27	#include <linux/mv643xx_eth.h>
3d014b01 AA	28	#include <linux/leds.h>
	29	#include <linux/gpio_keys.h>
	30	#include <linux/input.h>
0eb66974 CM	31	#include <linux/i2c.h>
	32	#include <linux/ata_platform.h>
	33	#include <linux/gpio.h>
	34	#include <asm/mach-types.h>
	35	#include <asm/mach/arch.h>
	36	#include <asm/mach/pci.h>
	37	#include <mach/orion5x.h>
	38	#include "common.h"
	39	#include "mpp.h"
	40
	41	/*****************************************************************************
	42	* EDMINI_V2 Info
	43	****************************************************************************/
	44
	45	/*
	46	* 512KB NOR flash Device bus boot chip select
	47	*/
	48
	49	#define EDMINI_V2_NOR_BOOT_BASE 0xfff80000
	50	#define EDMINI_V2_NOR_BOOT_SIZE SZ_512K
	51
	52	/*****************************************************************************
	53	* 512KB NOR Flash on BOOT Device
	54	****************************************************************************/
	55
	56	/*
	57	* Currently the MTD code does not recognize the MX29LV400CBCT as a bottom
	58	* -type device. This could cause risks of accidentally erasing critical
	59	* flash sectors. We thus define a single, write-protected partition covering
	60	* the whole flash.
	61	* TODO: once the flash part TOP/BOTTOM detection issue is sorted out in the MTD
	62	* code, break this into at least three partitions: 'u-boot code', 'u-boot
	63	* environment' and 'whatever is left'.
	64	*/
	65
	66	static struct mtd_partition edmini_v2_partitions[] = {
	67	{
	68	.name = "Full512kb",
	69	.size = 0x00080000,
	70	.offset = 0x00000000,
	71	.mask_flags = MTD_WRITEABLE,
	72	},
	73	};
	74
	75	static struct physmap_flash_data edmini_v2_nor_flash_data = {
	76	.width = 1,
	77	.parts = edmini_v2_partitions,
	78	.nr_parts = ARRAY_SIZE(edmini_v2_partitions),
	79	};
	80
	81	static struct resource edmini_v2_nor_flash_resource = {
	82	.flags = IORESOURCE_MEM,
	83	.start = EDMINI_V2_NOR_BOOT_BASE,
	84	.end = EDMINI_V2_NOR_BOOT_BASE
	85	+ EDMINI_V2_NOR_BOOT_SIZE - 1,
	86	};
	87
	88	static struct platform_device edmini_v2_nor_flash = {
	89	.name = "physmap-flash",
	90	.id = 0,
	91	.dev = {
	92	.platform_data = &edmini_v2_nor_flash_data,
	93	},
	94	.num_resources = 1,
95	.resource = &edmini_v2_nor_flash_resource,
96	};
97
98	/*****************************************************************************
99	* Ethernet
100	****************************************************************************/
101
102	static struct mv643xx_eth_platform_data edmini_v2_eth_data = {
103	.phy_addr = 8,
104	};
105
106	/*****************************************************************************
107	* RTC 5C372a on I2C bus
108	****************************************************************************/
109
110	#define EDMINIV2_RTC_GPIO 3
111
112	static struct i2c_board_info __initdata edmini_v2_i2c_rtc = {
113	I2C_BOARD_INFO("rs5c372a", 0x32),
114	.irq = 0,
115	};
116
117	/*****************************************************************************
118	* Sata
119	****************************************************************************/
120
121	static struct mv_sata_platform_data edmini_v2_sata_data = {
122	.n_ports = 2,
123	};
124
3d014b01 AA	125	/*****************************************************************************
	126	* GPIO LED (simple - doesn't use hardware blinking support)
	127	****************************************************************************/
	128
	129	#define EDMINI_V2_GPIO_LED_POWER 16
	130
	131	static struct gpio_led edmini_v2_leds[] = {
	132	{
	133	.name = "power:blue",
	134	.gpio = EDMINI_V2_GPIO_LED_POWER,
	135	.active_low = 1,
	136	},
	137	};
	138
	139	static struct gpio_led_platform_data edmini_v2_led_data = {
	140	.num_leds = ARRAY_SIZE(edmini_v2_leds),
	141	.leds = edmini_v2_leds,
	142	};
	143
	144	static struct platform_device edmini_v2_gpio_leds = {
	145	.name = "leds-gpio",
	146	.id = -1,
	147	.dev = {
	148	.platform_data = &edmini_v2_led_data,
	149	},
	150	};
	151
	152	/****************************************************************************
	153	* GPIO key
	154	****************************************************************************/
	155
	156	#define EDMINI_V2_GPIO_KEY_POWER 18
	157
	158	static struct gpio_keys_button edmini_v2_buttons[] = {
	159	{
	160	.code = KEY_POWER,
	161	.gpio = EDMINI_V2_GPIO_KEY_POWER,
	162	.desc = "Power Button",
	163	.active_low = 0,
	164	},
	165	};
	166
	167	static struct gpio_keys_platform_data edmini_v2_button_data = {
	168	.buttons = edmini_v2_buttons,
	169	.nbuttons = ARRAY_SIZE(edmini_v2_buttons),
	170	};
	171
	172	static struct platform_device edmini_v2_gpio_buttons = {
	173	.name = "gpio-keys",
	174	.id = -1,
	175	.dev = {
	176	.platform_data = &edmini_v2_button_data,
	177	},
	178	};
	179
0eb66974 CM	180	/*****************************************************************************
	181	* General Setup
	182	****************************************************************************/
554cdaef AL	183	static unsigned int edminiv2_mpp_modes[] __initdata = {
	184	MPP0_UNUSED,
	185	MPP1_UNUSED,
	186	MPP2_UNUSED,
	187	MPP3_GPIO, /* RTC interrupt */
	188	MPP4_UNUSED,
	189	MPP5_UNUSED,
	190	MPP6_UNUSED,
	191	MPP7_UNUSED,
	192	MPP8_UNUSED,
	193	MPP9_UNUSED,
	194	MPP10_UNUSED,
	195	MPP11_UNUSED,
	196	MPP12_SATA_LED, /* SATA 0 presence */
	197	MPP13_SATA_LED, /* SATA 1 presence */
	198	MPP14_SATA_LED, /* SATA 0 active */
	199	MPP15_SATA_LED, /* SATA 1 active */
0eb66974	200	/* 16: Power LED control (0 = On, 1 = Off) */
554cdaef	201	MPP16_GPIO,
0eb66974	202	/* 17: Power LED control select (0 = CPLD, 1 = GPIO16) */
554cdaef	203	MPP17_GPIO,
0eb66974	204	/* 18: Power button status (0 = Released, 1 = Pressed) */
554cdaef AL	205	MPP18_GPIO,
	206	MPP19_UNUSED,
	207	0,
0eb66974 CM	208	};
	209
	210	static void __init edmini_v2_init(void)
	211	{
	212	/*
	213	* Setup basic Orion functions. Need to be called early.
	214	*/
	215	orion5x_init();
	216
	217	orion5x_mpp_conf(edminiv2_mpp_modes);
	218
	219	/*
	220	* Configure peripherals.
	221	*/
	222	orion5x_ehci0_init();
	223	orion5x_eth_init(&edmini_v2_eth_data);
	224	orion5x_i2c_init();
	225	orion5x_sata_init(&edmini_v2_sata_data);
	226	orion5x_uart0_init();
	227
	228	orion5x_setup_dev_boot_win(EDMINI_V2_NOR_BOOT_BASE,
	229	EDMINI_V2_NOR_BOOT_SIZE);
	230	platform_device_register(&edmini_v2_nor_flash);
3d014b01 AA	231	platform_device_register(&edmini_v2_gpio_leds);
3d014b01 AA	232	platform_device_register(&edmini_v2_gpio_buttons);
0eb66974 CM	233
	234	pr_notice("edmini_v2: USB device port, flash write and power-off "
	235	"are not yet supported.\n");
	236
	237	/* Get RTC IRQ and register the chip */
	238	if (gpio_request(EDMINIV2_RTC_GPIO, "rtc") == 0) {
	239	if (gpio_direction_input(EDMINIV2_RTC_GPIO) == 0)
	240	edmini_v2_i2c_rtc.irq = gpio_to_irq(EDMINIV2_RTC_GPIO);
	241	else
	242	gpio_free(EDMINIV2_RTC_GPIO);
	243	}
	244
	245	if (edmini_v2_i2c_rtc.irq == 0)
	246	pr_warning("edmini_v2: failed to get RTC IRQ\n");
	247
	248	i2c_register_board_info(0, &edmini_v2_i2c_rtc, 1);
	249	}
	250
	251	/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
	252	MACHINE_START(EDMINI_V2, "LaCie Ethernet Disk mini V2")
	253	/* Maintainer: Christopher Moore <moore@free.fr> */
65aa1b1e	254	.atag_offset = 0x100,
0eb66974 CM	255	.init_machine = edmini_v2_init,
0eb66974 CM	256	.map_io = orion5x_map_io,
4ee1f6b5	257	.init_early = orion5x_init_early,
0eb66974 CM	258	.init_irq = orion5x_init_irq,
	259	.timer = &orion5x_timer,
	260	.fixup = tag_fixup_mem32,
764cbcc2	261	.restart = orion5x_restart,
0eb66974	262	MACHINE_END