[deliverable/linux.git] / arch / arm / mach-orion5x / net2big-setup.c

/*
 * arch/arm/mach-orion5x/net2big-setup.c
 *
 * LaCie 2Big Network NAS setup
 *
 * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
 *
 * This file is licensed under the terms of the GNU General Public
 * License version 2. This program is licensed "as is" without any
 * warranty of any kind, whether express or implied.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mtd/physmap.h>
#include <linux/mv643xx_eth.h>
#include <linux/leds.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/i2c.h>
#include <linux/ata_platform.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <plat/orion-gpio.h>
#include "common.h"
#include "mpp.h"
#include "orion5x.h"

/*****************************************************************************
 * LaCie 2Big Network Info
 ****************************************************************************/

/*
 * 512KB NOR flash Device bus boot chip select
 */

#define NET2BIG_NOR_BOOT_BASE		0xfff80000
#define NET2BIG_NOR_BOOT_SIZE		SZ_512K

/*****************************************************************************
 * 512KB NOR Flash on Boot Device
 ****************************************************************************/

/*
 * TODO: Check write support on flash MX29LV400CBTC-70G
 */

static struct mtd_partition net2big_partitions[] = {
	{
		.name		= "Full512kb",
		.size		= MTDPART_SIZ_FULL,
		.offset		= 0x00000000,
		.mask_flags	= MTD_WRITEABLE,
	},
};

static struct physmap_flash_data net2big_nor_flash_data = {
	.width		= 1,
	.parts		= net2big_partitions,
	.nr_parts	= ARRAY_SIZE(net2big_partitions),
};

static struct resource net2big_nor_flash_resource = {
	.flags			= IORESOURCE_MEM,
	.start			= NET2BIG_NOR_BOOT_BASE,
	.end			= NET2BIG_NOR_BOOT_BASE
					+ NET2BIG_NOR_BOOT_SIZE - 1,
};

static struct platform_device net2big_nor_flash = {
	.name			= "physmap-flash",
	.id			= 0,
	.dev		= {
		.platform_data	= &net2big_nor_flash_data,
	},
	.num_resources		= 1,
	.resource		= &net2big_nor_flash_resource,
};

/*****************************************************************************
 * Ethernet
 ****************************************************************************/

static struct mv643xx_eth_platform_data net2big_eth_data = {
	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
};

/*****************************************************************************
 * I2C devices
 ****************************************************************************/

/*
 * i2c addr | chip         | description
 * 0x32     | Ricoh 5C372b | RTC
 * 0x50     | HT24LC08     | eeprom (1kB)
 */
static struct i2c_board_info __initdata net2big_i2c_devices[] = {
	{
		I2C_BOARD_INFO("rs5c372b", 0x32),
	}, {
		I2C_BOARD_INFO("24c08", 0x50),
	},
};

/*****************************************************************************
 * SATA
 ****************************************************************************/

static struct mv_sata_platform_data net2big_sata_data = {
	.n_ports	= 2,
};

#define NET2BIG_GPIO_SATA_POWER_REQ	19
#define NET2BIG_GPIO_SATA0_POWER	23
#define NET2BIG_GPIO_SATA1_POWER	25

static void __init net2big_sata_power_init(void)
{
	int err;

	/* Configure GPIOs over MPP max number. */
	orion_gpio_set_valid(NET2BIG_GPIO_SATA0_POWER, 1);
	orion_gpio_set_valid(NET2BIG_GPIO_SATA1_POWER, 1);

	err = gpio_request(NET2BIG_GPIO_SATA0_POWER, "SATA0 power status");
	if (err == 0) {
		err = gpio_direction_input(NET2BIG_GPIO_SATA0_POWER);
		if (err)
			gpio_free(NET2BIG_GPIO_SATA0_POWER);
	}
	if (err) {
		pr_err("net2big: failed to setup SATA0 power GPIO\n");
		return;
	}

	err = gpio_request(NET2BIG_GPIO_SATA1_POWER, "SATA1 power status");
	if (err == 0) {
		err = gpio_direction_input(NET2BIG_GPIO_SATA1_POWER);
		if (err)
			gpio_free(NET2BIG_GPIO_SATA1_POWER);
	}
	if (err) {
		pr_err("net2big: failed to setup SATA1 power GPIO\n");
		goto err_free_1;
	}

	err = gpio_request(NET2BIG_GPIO_SATA_POWER_REQ, "SATA power request");
	if (err == 0) {
		err = gpio_direction_output(NET2BIG_GPIO_SATA_POWER_REQ, 0);
		if (err)
			gpio_free(NET2BIG_GPIO_SATA_POWER_REQ);
	}
	if (err) {
		pr_err("net2big: failed to setup SATA power request GPIO\n");
		goto err_free_2;
	}

	if (gpio_get_value(NET2BIG_GPIO_SATA0_POWER) &&
		gpio_get_value(NET2BIG_GPIO_SATA1_POWER)) {
		return;
	}

	/*
	 * SATA power up on both disk is done by pulling high the CPLD power
	 * request line. The 300ms delay is related to the CPLD clock and is
	 * needed to be sure that the CPLD has take into account the low line
	 * status.
	 */
	msleep(300);
	gpio_set_value(NET2BIG_GPIO_SATA_POWER_REQ, 1);
	pr_info("net2big: power up SATA hard disks\n");

	return;

err_free_2:
	gpio_free(NET2BIG_GPIO_SATA1_POWER);
err_free_1:
	gpio_free(NET2BIG_GPIO_SATA0_POWER);

	return;
}

/*****************************************************************************
 * GPIO LEDs
 ****************************************************************************/

/*
 * The power front LEDs (blue and red) and SATA red LEDs are controlled via a
 * single GPIO line and are compatible with the leds-gpio driver.
 *
 * The SATA blue LEDs have some hardware blink capabilities which are detailed
 * in the following array:
 *
 * SATAx blue LED | SATAx activity | LED state
 *                |                |
 *       0        |       0        |  blink (rate 300ms)
 *       1        |       0        |  off
 *       ?        |       1        |  on
 *
 * Notes: The blue and the red front LED's can't be on at the same time.
 *        Blue LED have priority.
 */

#define NET2BIG_GPIO_PWR_RED_LED	6
#define NET2BIG_GPIO_PWR_BLUE_LED	16
#define NET2BIG_GPIO_PWR_LED_BLINK_STOP	7

#define NET2BIG_GPIO_SATA0_RED_LED	11
#define NET2BIG_GPIO_SATA1_RED_LED	10

#define NET2BIG_GPIO_SATA0_BLUE_LED	17
#define NET2BIG_GPIO_SATA1_BLUE_LED	13

static struct gpio_led net2big_leds[] = {
	{
		.name = "net2big:red:power",
		.gpio = NET2BIG_GPIO_PWR_RED_LED,
	},
	{
		.name = "net2big:blue:power",
		.gpio = NET2BIG_GPIO_PWR_BLUE_LED,
	},
	{
		.name = "net2big:red:sata0",
		.gpio = NET2BIG_GPIO_SATA0_RED_LED,
	},
	{
		.name = "net2big:red:sata1",
		.gpio = NET2BIG_GPIO_SATA1_RED_LED,
	},
};

static struct gpio_led_platform_data net2big_led_data = {
	.num_leds = ARRAY_SIZE(net2big_leds),
	.leds = net2big_leds,
};

static struct platform_device net2big_gpio_leds = {
	.name           = "leds-gpio",
	.id             = -1,
	.dev            = {
		.platform_data  = &net2big_led_data,
	},
};

static void __init net2big_gpio_leds_init(void)
{
	int err;

	/* Stop initial CPLD slow red/blue blinking on power LED. */
	err = gpio_request(NET2BIG_GPIO_PWR_LED_BLINK_STOP,
			   "Power LED blink stop");
	if (err == 0) {
		err = gpio_direction_output(NET2BIG_GPIO_PWR_LED_BLINK_STOP, 1);
		if (err)
			gpio_free(NET2BIG_GPIO_PWR_LED_BLINK_STOP);
	}
	if (err)
		pr_err("net2big: failed to setup power LED blink GPIO\n");

	/*
	 * Configure SATA0 and SATA1 blue LEDs to blink in relation with the
	 * hard disk activity.
	 */
	err = gpio_request(NET2BIG_GPIO_SATA0_BLUE_LED,
			   "SATA0 blue LED control");
	if (err == 0) {
		err = gpio_direction_output(NET2BIG_GPIO_SATA0_BLUE_LED, 1);
		if (err)
			gpio_free(NET2BIG_GPIO_SATA0_BLUE_LED);
	}
	if (err)
		pr_err("net2big: failed to setup SATA0 blue LED GPIO\n");

	err = gpio_request(NET2BIG_GPIO_SATA1_BLUE_LED,
			   "SATA1 blue LED control");
	if (err == 0) {
		err = gpio_direction_output(NET2BIG_GPIO_SATA1_BLUE_LED, 1);
		if (err)
			gpio_free(NET2BIG_GPIO_SATA1_BLUE_LED);
	}
	if (err)
		pr_err("net2big: failed to setup SATA1 blue LED GPIO\n");

	platform_device_register(&net2big_gpio_leds);
}

/****************************************************************************
 * GPIO keys
 ****************************************************************************/

#define NET2BIG_GPIO_PUSH_BUTTON	18
#define NET2BIG_GPIO_POWER_SWITCH_ON	8
#define NET2BIG_GPIO_POWER_SWITCH_OFF	9

#define NET2BIG_SWITCH_POWER_ON		0x1
#define NET2BIG_SWITCH_POWER_OFF	0x2

static struct gpio_keys_button net2big_buttons[] = {
	{
		.type		= EV_SW,
		.code		= NET2BIG_SWITCH_POWER_OFF,
		.gpio		= NET2BIG_GPIO_POWER_SWITCH_OFF,
		.desc		= "Power rocker switch (auto|off)",
		.active_low	= 0,
	},
	{
		.type		= EV_SW,
		.code		= NET2BIG_SWITCH_POWER_ON,
		.gpio		= NET2BIG_GPIO_POWER_SWITCH_ON,
		.desc		= "Power rocker switch (on|auto)",
		.active_low	= 0,
	},
	{
		.type		= EV_KEY,
		.code		= KEY_POWER,
		.gpio		= NET2BIG_GPIO_PUSH_BUTTON,
		.desc		= "Front Push Button",
		.active_low	= 0,
	},
};

static struct gpio_keys_platform_data net2big_button_data = {
	.buttons	= net2big_buttons,
	.nbuttons	= ARRAY_SIZE(net2big_buttons),
};

static struct platform_device net2big_gpio_buttons = {
	.name		= "gpio-keys",
	.id		= -1,
	.dev		= {
		.platform_data	= &net2big_button_data,
	},
};

/*****************************************************************************
 * General Setup
 ****************************************************************************/

static unsigned int net2big_mpp_modes[] __initdata = {
	MPP0_GPIO,	/* Raid mode (bit 0) */
	MPP1_GPIO,	/* USB port 2 fuse (0 = Fail, 1 = Ok) */
	MPP2_GPIO,	/* Raid mode (bit 1) */
	MPP3_GPIO,	/* Board ID (bit 0) */
	MPP4_GPIO,	/* Fan activity (0 = Off, 1 = On) */
	MPP5_GPIO,	/* Fan fail detection */
	MPP6_GPIO,	/* Red front LED (0 = Off, 1 = On) */
	MPP7_GPIO,	/* Disable initial blinking on front LED */
	MPP8_GPIO,	/* Rear power switch (on|auto) */
	MPP9_GPIO,	/* Rear power switch (auto|off) */
	MPP10_GPIO,	/* SATA 1 red LED (0 = Off, 1 = On) */
	MPP11_GPIO,	/* SATA 0 red LED (0 = Off, 1 = On) */
	MPP12_GPIO,	/* Board ID (bit 1) */
	MPP13_GPIO,	/* SATA 1 blue LED blink control */
	MPP14_SATA_LED,
	MPP15_SATA_LED,
	MPP16_GPIO,	/* Blue front LED control */
	MPP17_GPIO,	/* SATA 0 blue LED blink control */
	MPP18_GPIO,	/* Front button (0 = Released, 1 = Pushed ) */
	MPP19_GPIO,	/* SATA{0,1} power On/Off request */
	0,
	/* 22: USB port 1 fuse (0 = Fail, 1 = Ok) */
	/* 23: SATA 0 power status */
	/* 24: Board power off */
	/* 25: SATA 1 power status */
};

#define NET2BIG_GPIO_POWER_OFF		24

static void net2big_power_off(void)
{
	gpio_set_value(NET2BIG_GPIO_POWER_OFF, 1);
}

static void __init net2big_init(void)
{
	/*
	 * Setup basic Orion functions. Need to be called early.
	 */
	orion5x_init();

	orion5x_mpp_conf(net2big_mpp_modes);

	/*
	 * Configure peripherals.
	 */
	orion5x_ehci0_init();
	orion5x_ehci1_init();
	orion5x_eth_init(&net2big_eth_data);
	orion5x_i2c_init();
	orion5x_uart0_init();
	orion5x_xor_init();

	net2big_sata_power_init();
	orion5x_sata_init(&net2big_sata_data);

	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
				    ORION_MBUS_DEVBUS_BOOT_ATTR,
				    NET2BIG_NOR_BOOT_BASE,
				    NET2BIG_NOR_BOOT_SIZE);
	platform_device_register(&net2big_nor_flash);

	platform_device_register(&net2big_gpio_buttons);
	net2big_gpio_leds_init();

	i2c_register_board_info(0, net2big_i2c_devices,
				ARRAY_SIZE(net2big_i2c_devices));

	orion_gpio_set_valid(NET2BIG_GPIO_POWER_OFF, 1);

	if (gpio_request(NET2BIG_GPIO_POWER_OFF, "power-off") == 0 &&
	    gpio_direction_output(NET2BIG_GPIO_POWER_OFF, 0) == 0)
		pm_power_off = net2big_power_off;
	else
		pr_err("net2big: failed to configure power-off GPIO\n");

	pr_notice("net2big: Flash writing is not yet supported.\n");
}

/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
MACHINE_START(NET2BIG, "LaCie 2Big Network")
	.atag_offset	= 0x100,
	.nr_irqs	= ORION5X_NR_IRQS,
	.init_machine	= net2big_init,
	.map_io		= orion5x_map_io,
	.init_early	= orion5x_init_early,
	.init_irq	= orion5x_init_irq,
	.init_time	= orion5x_timer_init,
	.fixup		= tag_fixup_mem32,
	.restart	= orion5x_restart,
MACHINE_END
Commit	Line	Data
54782674 SG	1	/*
	2	* arch/arm/mach-orion5x/net2big-setup.c
	3	*
	4	* LaCie 2Big Network NAS setup
	5	*
	6	* Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
	7	*
	8	* This file is licensed under the terms of the GNU General Public
	9	* License version 2. This program is licensed "as is" without any
	10	* warranty of any kind, whether express or implied.
	11	*/
	12
	13	#include <linux/kernel.h>
	14	#include <linux/init.h>
	15	#include <linux/platform_device.h>
	16	#include <linux/mtd/physmap.h>
	17	#include <linux/mv643xx_eth.h>
	18	#include <linux/leds.h>
	19	#include <linux/gpio_keys.h>
	20	#include <linux/input.h>
	21	#include <linux/i2c.h>
	22	#include <linux/ata_platform.h>
	23	#include <linux/gpio.h>
	24	#include <linux/delay.h>
	25	#include <asm/mach-types.h>
	26	#include <asm/mach/arch.h>
ce91574c	27	#include <plat/orion-gpio.h>
54782674 SG	28	#include "common.h"
54782674 SG	29	#include "mpp.h"
c22c2c60	30	#include "orion5x.h"
54782674 SG	31
	32	/*****************************************************************************
	33	* LaCie 2Big Network Info
	34	****************************************************************************/
	35
	36	/*
	37	* 512KB NOR flash Device bus boot chip select
	38	*/
	39
	40	#define NET2BIG_NOR_BOOT_BASE 0xfff80000
	41	#define NET2BIG_NOR_BOOT_SIZE SZ_512K
	42
	43	/*****************************************************************************
	44	* 512KB NOR Flash on Boot Device
	45	****************************************************************************/
	46
	47	/*
	48	* TODO: Check write support on flash MX29LV400CBTC-70G
	49	*/
	50
	51	static struct mtd_partition net2big_partitions[] = {
	52	{
	53	.name = "Full512kb",
	54	.size = MTDPART_SIZ_FULL,
	55	.offset = 0x00000000,
	56	.mask_flags = MTD_WRITEABLE,
	57	},
	58	};
	59
	60	static struct physmap_flash_data net2big_nor_flash_data = {
	61	.width = 1,
	62	.parts = net2big_partitions,
	63	.nr_parts = ARRAY_SIZE(net2big_partitions),
	64	};
	65
	66	static struct resource net2big_nor_flash_resource = {
	67	.flags = IORESOURCE_MEM,
	68	.start = NET2BIG_NOR_BOOT_BASE,
	69	.end = NET2BIG_NOR_BOOT_BASE
	70	+ NET2BIG_NOR_BOOT_SIZE - 1,
	71	};
	72
	73	static struct platform_device net2big_nor_flash = {
	74	.name = "physmap-flash",
	75	.id = 0,
	76	.dev = {
	77	.platform_data = &net2big_nor_flash_data,
	78	},
	79	.num_resources = 1,
	80	.resource = &net2big_nor_flash_resource,
	81	};
	82
	83	/*****************************************************************************
	84	* Ethernet
	85	****************************************************************************/
	86
	87	static struct mv643xx_eth_platform_data net2big_eth_data = {
	88	.phy_addr = MV643XX_ETH_PHY_ADDR(8),
	89	};
	90
	91	/*****************************************************************************
	92	* I2C devices
	93	****************************************************************************/
	94
95	/*
96	* i2c addr \| chip \| description
97	* 0x32 \| Ricoh 5C372b \| RTC
98	* 0x50 \| HT24LC08 \| eeprom (1kB)
99	*/
100	static struct i2c_board_info __initdata net2big_i2c_devices[] = {
101	{
102	I2C_BOARD_INFO("rs5c372b", 0x32),
103	}, {
104	I2C_BOARD_INFO("24c08", 0x50),
105	},
106	};
107
108	/*****************************************************************************
109	* SATA
110	****************************************************************************/
111
112	static struct mv_sata_platform_data net2big_sata_data = {
113	.n_ports = 2,
114	};
115
116	#define NET2BIG_GPIO_SATA_POWER_REQ 19
117	#define NET2BIG_GPIO_SATA0_POWER 23
118	#define NET2BIG_GPIO_SATA1_POWER 25
119
120	static void __init net2big_sata_power_init(void)
121	{
122	int err;
123
124	/* Configure GPIOs over MPP max number. */
125	orion_gpio_set_valid(NET2BIG_GPIO_SATA0_POWER, 1);
126	orion_gpio_set_valid(NET2BIG_GPIO_SATA1_POWER, 1);
127
128	err = gpio_request(NET2BIG_GPIO_SATA0_POWER, "SATA0 power status");
129	if (err == 0) {
130	err = gpio_direction_input(NET2BIG_GPIO_SATA0_POWER);
131	if (err)
132	gpio_free(NET2BIG_GPIO_SATA0_POWER);
133	}
134	if (err) {
135	pr_err("net2big: failed to setup SATA0 power GPIO\n");
136	return;
137	}
138
139	err = gpio_request(NET2BIG_GPIO_SATA1_POWER, "SATA1 power status");
140	if (err == 0) {
141	err = gpio_direction_input(NET2BIG_GPIO_SATA1_POWER);
142	if (err)
143	gpio_free(NET2BIG_GPIO_SATA1_POWER);
144	}
145	if (err) {
146	pr_err("net2big: failed to setup SATA1 power GPIO\n");
147	goto err_free_1;
148	}
149
150	err = gpio_request(NET2BIG_GPIO_SATA_POWER_REQ, "SATA power request");
151	if (err == 0) {
152	err = gpio_direction_output(NET2BIG_GPIO_SATA_POWER_REQ, 0);
153	if (err)
154	gpio_free(NET2BIG_GPIO_SATA_POWER_REQ);
155	}
156	if (err) {
157	pr_err("net2big: failed to setup SATA power request GPIO\n");
158	goto err_free_2;
159	}
160
161	if (gpio_get_value(NET2BIG_GPIO_SATA0_POWER) &&
162	gpio_get_value(NET2BIG_GPIO_SATA1_POWER)) {
163	return;
164	}
165
166	/*
167	* SATA power up on both disk is done by pulling high the CPLD power
168	* request line. The 300ms delay is related to the CPLD clock and is
169	* needed to be sure that the CPLD has take into account the low line
170	* status.
171	*/
172	msleep(300);
173	gpio_set_value(NET2BIG_GPIO_SATA_POWER_REQ, 1);
174	pr_info("net2big: power up SATA hard disks\n");
175
176	return;
177
178	err_free_2:
179	gpio_free(NET2BIG_GPIO_SATA1_POWER);
180	err_free_1:
181	gpio_free(NET2BIG_GPIO_SATA0_POWER);
182
183	return;
184	}
185
186	/*****************************************************************************
187	* GPIO LEDs
188	****************************************************************************/
189
190	/*
191	* The power front LEDs (blue and red) and SATA red LEDs are controlled via a
192	* single GPIO line and are compatible with the leds-gpio driver.
193	*
25985edc	194	* The SATA blue LEDs have some hardware blink capabilities which are detailed
54782674 SG	195	* in the following array:
	196	*
	197	* SATAx blue LED \| SATAx activity \| LED state
	198	* \| \|
	199	* 0 \| 0 \| blink (rate 300ms)
	200	* 1 \| 0 \| off
	201	* ? \| 1 \| on
	202	*
	203	* Notes: The blue and the red front LED's can't be on at the same time.
	204	* Blue LED have priority.
	205	*/
	206
	207	#define NET2BIG_GPIO_PWR_RED_LED 6
	208	#define NET2BIG_GPIO_PWR_BLUE_LED 16
	209	#define NET2BIG_GPIO_PWR_LED_BLINK_STOP 7
	210
	211	#define NET2BIG_GPIO_SATA0_RED_LED 11
	212	#define NET2BIG_GPIO_SATA1_RED_LED 10
	213
	214	#define NET2BIG_GPIO_SATA0_BLUE_LED 17
	215	#define NET2BIG_GPIO_SATA1_BLUE_LED 13
	216
	217	static struct gpio_led net2big_leds[] = {
	218	{
	219	.name = "net2big:red:power",
	220	.gpio = NET2BIG_GPIO_PWR_RED_LED,
	221	},
	222	{
	223	.name = "net2big:blue:power",
	224	.gpio = NET2BIG_GPIO_PWR_BLUE_LED,
	225	},
	226	{
	227	.name = "net2big:red:sata0",
	228	.gpio = NET2BIG_GPIO_SATA0_RED_LED,
	229	},
	230	{
	231	.name = "net2big:red:sata1",
	232	.gpio = NET2BIG_GPIO_SATA1_RED_LED,
	233	},
	234	};
	235
	236	static struct gpio_led_platform_data net2big_led_data = {
	237	.num_leds = ARRAY_SIZE(net2big_leds),
	238	.leds = net2big_leds,
	239	};
	240
	241	static struct platform_device net2big_gpio_leds = {
	242	.name = "leds-gpio",
	243	.id = -1,
	244	.dev = {
	245	.platform_data = &net2big_led_data,
	246	},
	247	};
	248
	249	static void __init net2big_gpio_leds_init(void)
	250	{
	251	int err;
	252
	253	/* Stop initial CPLD slow red/blue blinking on power LED. */
	254	err = gpio_request(NET2BIG_GPIO_PWR_LED_BLINK_STOP,
	255	"Power LED blink stop");
	256	if (err == 0) {
	257	err = gpio_direction_output(NET2BIG_GPIO_PWR_LED_BLINK_STOP, 1);
	258	if (err)
259	gpio_free(NET2BIG_GPIO_PWR_LED_BLINK_STOP);
260	}
261	if (err)
262	pr_err("net2big: failed to setup power LED blink GPIO\n");
263
264	/*
265	* Configure SATA0 and SATA1 blue LEDs to blink in relation with the
266	* hard disk activity.
267	*/
268	err = gpio_request(NET2BIG_GPIO_SATA0_BLUE_LED,
269	"SATA0 blue LED control");
270	if (err == 0) {
271	err = gpio_direction_output(NET2BIG_GPIO_SATA0_BLUE_LED, 1);
272	if (err)
273	gpio_free(NET2BIG_GPIO_SATA0_BLUE_LED);
274	}
275	if (err)
276	pr_err("net2big: failed to setup SATA0 blue LED GPIO\n");
277
278	err = gpio_request(NET2BIG_GPIO_SATA1_BLUE_LED,
279	"SATA1 blue LED control");
280	if (err == 0) {
281	err = gpio_direction_output(NET2BIG_GPIO_SATA1_BLUE_LED, 1);
282	if (err)
283	gpio_free(NET2BIG_GPIO_SATA1_BLUE_LED);
284	}
285	if (err)
286	pr_err("net2big: failed to setup SATA1 blue LED GPIO\n");
287
288	platform_device_register(&net2big_gpio_leds);
289	}
290
291	/****************************************************************************
292	* GPIO keys
293	****************************************************************************/
294
295	#define NET2BIG_GPIO_PUSH_BUTTON 18
296	#define NET2BIG_GPIO_POWER_SWITCH_ON 8
297	#define NET2BIG_GPIO_POWER_SWITCH_OFF 9
298
299	#define NET2BIG_SWITCH_POWER_ON 0x1
300	#define NET2BIG_SWITCH_POWER_OFF 0x2
301
302	static struct gpio_keys_button net2big_buttons[] = {
303	{
304	.type = EV_SW,
305	.code = NET2BIG_SWITCH_POWER_OFF,
306	.gpio = NET2BIG_GPIO_POWER_SWITCH_OFF,
307	.desc = "Power rocker switch (auto\|off)",
308	.active_low = 0,
309	},
310	{
311	.type = EV_SW,
312	.code = NET2BIG_SWITCH_POWER_ON,
313	.gpio = NET2BIG_GPIO_POWER_SWITCH_ON,
314	.desc = "Power rocker switch (on\|auto)",
315	.active_low = 0,
316	},
317	{
318	.type = EV_KEY,
319	.code = KEY_POWER,
320	.gpio = NET2BIG_GPIO_PUSH_BUTTON,
321	.desc = "Front Push Button",
322	.active_low = 0,
323	},
324	};
325
326	static struct gpio_keys_platform_data net2big_button_data = {
327	.buttons = net2big_buttons,
328	.nbuttons = ARRAY_SIZE(net2big_buttons),
329	};
330
331	static struct platform_device net2big_gpio_buttons = {
332	.name = "gpio-keys",
333	.id = -1,
334	.dev = {
335	.platform_data = &net2big_button_data,
336	},
337	};
338
339	/*****************************************************************************
340	* General Setup
341	****************************************************************************/
342
554cdaef AL	343	static unsigned int net2big_mpp_modes[] __initdata = {
	344	MPP0_GPIO, /* Raid mode (bit 0) */
	345	MPP1_GPIO, /* USB port 2 fuse (0 = Fail, 1 = Ok) */
	346	MPP2_GPIO, /* Raid mode (bit 1) */
	347	MPP3_GPIO, /* Board ID (bit 0) */
	348	MPP4_GPIO, /* Fan activity (0 = Off, 1 = On) */
	349	MPP5_GPIO, /* Fan fail detection */
	350	MPP6_GPIO, /* Red front LED (0 = Off, 1 = On) */
	351	MPP7_GPIO, /* Disable initial blinking on front LED */
	352	MPP8_GPIO, /* Rear power switch (on\|auto) */
	353	MPP9_GPIO, /* Rear power switch (auto\|off) */
	354	MPP10_GPIO, /* SATA 1 red LED (0 = Off, 1 = On) */
	355	MPP11_GPIO, /* SATA 0 red LED (0 = Off, 1 = On) */
	356	MPP12_GPIO, /* Board ID (bit 1) */
	357	MPP13_GPIO, /* SATA 1 blue LED blink control */
	358	MPP14_SATA_LED,
	359	MPP15_SATA_LED,
	360	MPP16_GPIO, /* Blue front LED control */
	361	MPP17_GPIO, /* SATA 0 blue LED blink control */
	362	MPP18_GPIO, /* Front button (0 = Released, 1 = Pushed ) */
	363	MPP19_GPIO, /* SATA{0,1} power On/Off request */
	364	0,
54782674 SG	365	/* 22: USB port 1 fuse (0 = Fail, 1 = Ok) */
	366	/* 23: SATA 0 power status */
	367	/* 24: Board power off */
	368	/* 25: SATA 1 power status */
	369	};
	370
	371	#define NET2BIG_GPIO_POWER_OFF 24
	372
	373	static void net2big_power_off(void)
	374	{
	375	gpio_set_value(NET2BIG_GPIO_POWER_OFF, 1);
	376	}
	377
	378	static void __init net2big_init(void)
	379	{
	380	/*
	381	* Setup basic Orion functions. Need to be called early.
	382	*/
	383	orion5x_init();
	384
	385	orion5x_mpp_conf(net2big_mpp_modes);
	386
	387	/*
	388	* Configure peripherals.
	389	*/
	390	orion5x_ehci0_init();
	391	orion5x_ehci1_init();
	392	orion5x_eth_init(&net2big_eth_data);
	393	orion5x_i2c_init();
	394	orion5x_uart0_init();
	395	orion5x_xor_init();
	396
	397	net2big_sata_power_init();
	398	orion5x_sata_init(&net2big_sata_data);
	399
4ca2c040 TP	400	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
	401	ORION_MBUS_DEVBUS_BOOT_ATTR,
	402	NET2BIG_NOR_BOOT_BASE,
	403	NET2BIG_NOR_BOOT_SIZE);
54782674 SG	404	platform_device_register(&net2big_nor_flash);
	405
	406	platform_device_register(&net2big_gpio_buttons);
	407	net2big_gpio_leds_init();
	408
	409	i2c_register_board_info(0, net2big_i2c_devices,
	410	ARRAY_SIZE(net2big_i2c_devices));
	411
	412	orion_gpio_set_valid(NET2BIG_GPIO_POWER_OFF, 1);
	413
	414	if (gpio_request(NET2BIG_GPIO_POWER_OFF, "power-off") == 0 &&
	415	gpio_direction_output(NET2BIG_GPIO_POWER_OFF, 0) == 0)
	416	pm_power_off = net2big_power_off;
	417	else
	418	pr_err("net2big: failed to configure power-off GPIO\n");
	419
	420	pr_notice("net2big: Flash writing is not yet supported.\n");
	421	}
	422
	423	/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
	424	MACHINE_START(NET2BIG, "LaCie 2Big Network")
65aa1b1e	425	.atag_offset = 0x100,
5cdbe5d2	426	.nr_irqs = ORION5X_NR_IRQS,
54782674 SG	427	.init_machine = net2big_init,
54782674 SG	428	.map_io = orion5x_map_io,
4ee1f6b5	429	.init_early = orion5x_init_early,
54782674	430	.init_irq = orion5x_init_irq,
6bb27d73	431	.init_time = orion5x_timer_init,
54782674	432	.fixup = tag_fixup_mem32,
764cbcc2	433	.restart = orion5x_restart,
54782674 SG	434	MACHINE_END
54782674 SG	435