Commit | Line | Data |
---|---|---|
bb3cee2b LW |
1 | /* |
2 | * | |
3 | * arch/arm/mach-u300/timer.c | |
4 | * | |
5 | * | |
6 | * Copyright (C) 2007-2009 ST-Ericsson AB | |
7 | * License terms: GNU General Public License (GPL) version 2 | |
8 | * Timer COH 901 328, runs the OS timer interrupt. | |
9 | * Author: Linus Walleij <linus.walleij@stericsson.com> | |
10 | */ | |
11 | #include <linux/interrupt.h> | |
12 | #include <linux/time.h> | |
13 | #include <linux/timex.h> | |
14 | #include <linux/clockchips.h> | |
15 | #include <linux/clocksource.h> | |
16 | #include <linux/types.h> | |
17 | #include <linux/io.h> | |
18 | ||
19 | #include <mach/hardware.h> | |
20 | ||
21 | /* Generic stuff */ | |
22 | #include <asm/mach/map.h> | |
23 | #include <asm/mach/time.h> | |
24 | #include <asm/mach/irq.h> | |
25 | ||
26 | #include "clock.h" | |
27 | ||
28 | /* | |
29 | * APP side special timer registers | |
30 | * This timer contains four timers which can fire an interrupt each. | |
31 | * OS (operating system) timer @ 32768 Hz | |
32 | * DD (device driver) timer @ 1 kHz | |
33 | * GP1 (general purpose 1) timer @ 1MHz | |
34 | * GP2 (general purpose 2) timer @ 1MHz | |
35 | */ | |
36 | ||
37 | /* Reset OS Timer 32bit (-/W) */ | |
38 | #define U300_TIMER_APP_ROST (0x0000) | |
39 | #define U300_TIMER_APP_ROST_TIMER_RESET (0x00000000) | |
40 | /* Enable OS Timer 32bit (-/W) */ | |
41 | #define U300_TIMER_APP_EOST (0x0004) | |
42 | #define U300_TIMER_APP_EOST_TIMER_ENABLE (0x00000000) | |
43 | /* Disable OS Timer 32bit (-/W) */ | |
44 | #define U300_TIMER_APP_DOST (0x0008) | |
45 | #define U300_TIMER_APP_DOST_TIMER_DISABLE (0x00000000) | |
46 | /* OS Timer Mode Register 32bit (-/W) */ | |
47 | #define U300_TIMER_APP_SOSTM (0x000c) | |
48 | #define U300_TIMER_APP_SOSTM_MODE_CONTINUOUS (0x00000000) | |
49 | #define U300_TIMER_APP_SOSTM_MODE_ONE_SHOT (0x00000001) | |
50 | /* OS Timer Status Register 32bit (R/-) */ | |
51 | #define U300_TIMER_APP_OSTS (0x0010) | |
52 | #define U300_TIMER_APP_OSTS_TIMER_STATE_MASK (0x0000000F) | |
53 | #define U300_TIMER_APP_OSTS_TIMER_STATE_IDLE (0x00000001) | |
54 | #define U300_TIMER_APP_OSTS_TIMER_STATE_ACTIVE (0x00000002) | |
55 | #define U300_TIMER_APP_OSTS_ENABLE_IND (0x00000010) | |
56 | #define U300_TIMER_APP_OSTS_MODE_MASK (0x00000020) | |
57 | #define U300_TIMER_APP_OSTS_MODE_CONTINUOUS (0x00000000) | |
58 | #define U300_TIMER_APP_OSTS_MODE_ONE_SHOT (0x00000020) | |
59 | #define U300_TIMER_APP_OSTS_IRQ_ENABLED_IND (0x00000040) | |
60 | #define U300_TIMER_APP_OSTS_IRQ_PENDING_IND (0x00000080) | |
61 | /* OS Timer Current Count Register 32bit (R/-) */ | |
62 | #define U300_TIMER_APP_OSTCC (0x0014) | |
63 | /* OS Timer Terminal Count Register 32bit (R/W) */ | |
64 | #define U300_TIMER_APP_OSTTC (0x0018) | |
65 | /* OS Timer Interrupt Enable Register 32bit (-/W) */ | |
66 | #define U300_TIMER_APP_OSTIE (0x001c) | |
67 | #define U300_TIMER_APP_OSTIE_IRQ_DISABLE (0x00000000) | |
68 | #define U300_TIMER_APP_OSTIE_IRQ_ENABLE (0x00000001) | |
69 | /* OS Timer Interrupt Acknowledge Register 32bit (-/W) */ | |
70 | #define U300_TIMER_APP_OSTIA (0x0020) | |
71 | #define U300_TIMER_APP_OSTIA_IRQ_ACK (0x00000080) | |
72 | ||
73 | /* Reset DD Timer 32bit (-/W) */ | |
74 | #define U300_TIMER_APP_RDDT (0x0040) | |
75 | #define U300_TIMER_APP_RDDT_TIMER_RESET (0x00000000) | |
76 | /* Enable DD Timer 32bit (-/W) */ | |
77 | #define U300_TIMER_APP_EDDT (0x0044) | |
78 | #define U300_TIMER_APP_EDDT_TIMER_ENABLE (0x00000000) | |
79 | /* Disable DD Timer 32bit (-/W) */ | |
80 | #define U300_TIMER_APP_DDDT (0x0048) | |
81 | #define U300_TIMER_APP_DDDT_TIMER_DISABLE (0x00000000) | |
82 | /* DD Timer Mode Register 32bit (-/W) */ | |
83 | #define U300_TIMER_APP_SDDTM (0x004c) | |
84 | #define U300_TIMER_APP_SDDTM_MODE_CONTINUOUS (0x00000000) | |
85 | #define U300_TIMER_APP_SDDTM_MODE_ONE_SHOT (0x00000001) | |
86 | /* DD Timer Status Register 32bit (R/-) */ | |
87 | #define U300_TIMER_APP_DDTS (0x0050) | |
88 | #define U300_TIMER_APP_DDTS_TIMER_STATE_MASK (0x0000000F) | |
89 | #define U300_TIMER_APP_DDTS_TIMER_STATE_IDLE (0x00000001) | |
90 | #define U300_TIMER_APP_DDTS_TIMER_STATE_ACTIVE (0x00000002) | |
91 | #define U300_TIMER_APP_DDTS_ENABLE_IND (0x00000010) | |
92 | #define U300_TIMER_APP_DDTS_MODE_MASK (0x00000020) | |
93 | #define U300_TIMER_APP_DDTS_MODE_CONTINUOUS (0x00000000) | |
94 | #define U300_TIMER_APP_DDTS_MODE_ONE_SHOT (0x00000020) | |
95 | #define U300_TIMER_APP_DDTS_IRQ_ENABLED_IND (0x00000040) | |
96 | #define U300_TIMER_APP_DDTS_IRQ_PENDING_IND (0x00000080) | |
97 | /* DD Timer Current Count Register 32bit (R/-) */ | |
98 | #define U300_TIMER_APP_DDTCC (0x0054) | |
99 | /* DD Timer Terminal Count Register 32bit (R/W) */ | |
100 | #define U300_TIMER_APP_DDTTC (0x0058) | |
101 | /* DD Timer Interrupt Enable Register 32bit (-/W) */ | |
102 | #define U300_TIMER_APP_DDTIE (0x005c) | |
103 | #define U300_TIMER_APP_DDTIE_IRQ_DISABLE (0x00000000) | |
104 | #define U300_TIMER_APP_DDTIE_IRQ_ENABLE (0x00000001) | |
105 | /* DD Timer Interrupt Acknowledge Register 32bit (-/W) */ | |
106 | #define U300_TIMER_APP_DDTIA (0x0060) | |
107 | #define U300_TIMER_APP_DDTIA_IRQ_ACK (0x00000080) | |
108 | ||
109 | /* Reset GP1 Timer 32bit (-/W) */ | |
110 | #define U300_TIMER_APP_RGPT1 (0x0080) | |
111 | #define U300_TIMER_APP_RGPT1_TIMER_RESET (0x00000000) | |
112 | /* Enable GP1 Timer 32bit (-/W) */ | |
113 | #define U300_TIMER_APP_EGPT1 (0x0084) | |
114 | #define U300_TIMER_APP_EGPT1_TIMER_ENABLE (0x00000000) | |
115 | /* Disable GP1 Timer 32bit (-/W) */ | |
116 | #define U300_TIMER_APP_DGPT1 (0x0088) | |
117 | #define U300_TIMER_APP_DGPT1_TIMER_DISABLE (0x00000000) | |
118 | /* GP1 Timer Mode Register 32bit (-/W) */ | |
119 | #define U300_TIMER_APP_SGPT1M (0x008c) | |
120 | #define U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS (0x00000000) | |
121 | #define U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT (0x00000001) | |
122 | /* GP1 Timer Status Register 32bit (R/-) */ | |
123 | #define U300_TIMER_APP_GPT1S (0x0090) | |
124 | #define U300_TIMER_APP_GPT1S_TIMER_STATE_MASK (0x0000000F) | |
125 | #define U300_TIMER_APP_GPT1S_TIMER_STATE_IDLE (0x00000001) | |
126 | #define U300_TIMER_APP_GPT1S_TIMER_STATE_ACTIVE (0x00000002) | |
127 | #define U300_TIMER_APP_GPT1S_ENABLE_IND (0x00000010) | |
128 | #define U300_TIMER_APP_GPT1S_MODE_MASK (0x00000020) | |
129 | #define U300_TIMER_APP_GPT1S_MODE_CONTINUOUS (0x00000000) | |
130 | #define U300_TIMER_APP_GPT1S_MODE_ONE_SHOT (0x00000020) | |
131 | #define U300_TIMER_APP_GPT1S_IRQ_ENABLED_IND (0x00000040) | |
132 | #define U300_TIMER_APP_GPT1S_IRQ_PENDING_IND (0x00000080) | |
133 | /* GP1 Timer Current Count Register 32bit (R/-) */ | |
134 | #define U300_TIMER_APP_GPT1CC (0x0094) | |
135 | /* GP1 Timer Terminal Count Register 32bit (R/W) */ | |
136 | #define U300_TIMER_APP_GPT1TC (0x0098) | |
137 | /* GP1 Timer Interrupt Enable Register 32bit (-/W) */ | |
138 | #define U300_TIMER_APP_GPT1IE (0x009c) | |
139 | #define U300_TIMER_APP_GPT1IE_IRQ_DISABLE (0x00000000) | |
140 | #define U300_TIMER_APP_GPT1IE_IRQ_ENABLE (0x00000001) | |
141 | /* GP1 Timer Interrupt Acknowledge Register 32bit (-/W) */ | |
142 | #define U300_TIMER_APP_GPT1IA (0x00a0) | |
143 | #define U300_TIMER_APP_GPT1IA_IRQ_ACK (0x00000080) | |
144 | ||
145 | /* Reset GP2 Timer 32bit (-/W) */ | |
146 | #define U300_TIMER_APP_RGPT2 (0x00c0) | |
147 | #define U300_TIMER_APP_RGPT2_TIMER_RESET (0x00000000) | |
148 | /* Enable GP2 Timer 32bit (-/W) */ | |
149 | #define U300_TIMER_APP_EGPT2 (0x00c4) | |
150 | #define U300_TIMER_APP_EGPT2_TIMER_ENABLE (0x00000000) | |
151 | /* Disable GP2 Timer 32bit (-/W) */ | |
152 | #define U300_TIMER_APP_DGPT2 (0x00c8) | |
153 | #define U300_TIMER_APP_DGPT2_TIMER_DISABLE (0x00000000) | |
154 | /* GP2 Timer Mode Register 32bit (-/W) */ | |
155 | #define U300_TIMER_APP_SGPT2M (0x00cc) | |
156 | #define U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS (0x00000000) | |
157 | #define U300_TIMER_APP_SGPT2M_MODE_ONE_SHOT (0x00000001) | |
158 | /* GP2 Timer Status Register 32bit (R/-) */ | |
159 | #define U300_TIMER_APP_GPT2S (0x00d0) | |
160 | #define U300_TIMER_APP_GPT2S_TIMER_STATE_MASK (0x0000000F) | |
161 | #define U300_TIMER_APP_GPT2S_TIMER_STATE_IDLE (0x00000001) | |
162 | #define U300_TIMER_APP_GPT2S_TIMER_STATE_ACTIVE (0x00000002) | |
163 | #define U300_TIMER_APP_GPT2S_ENABLE_IND (0x00000010) | |
164 | #define U300_TIMER_APP_GPT2S_MODE_MASK (0x00000020) | |
165 | #define U300_TIMER_APP_GPT2S_MODE_CONTINUOUS (0x00000000) | |
166 | #define U300_TIMER_APP_GPT2S_MODE_ONE_SHOT (0x00000020) | |
167 | #define U300_TIMER_APP_GPT2S_IRQ_ENABLED_IND (0x00000040) | |
168 | #define U300_TIMER_APP_GPT2S_IRQ_PENDING_IND (0x00000080) | |
169 | /* GP2 Timer Current Count Register 32bit (R/-) */ | |
170 | #define U300_TIMER_APP_GPT2CC (0x00d4) | |
171 | /* GP2 Timer Terminal Count Register 32bit (R/W) */ | |
172 | #define U300_TIMER_APP_GPT2TC (0x00d8) | |
173 | /* GP2 Timer Interrupt Enable Register 32bit (-/W) */ | |
174 | #define U300_TIMER_APP_GPT2IE (0x00dc) | |
175 | #define U300_TIMER_APP_GPT2IE_IRQ_DISABLE (0x00000000) | |
176 | #define U300_TIMER_APP_GPT2IE_IRQ_ENABLE (0x00000001) | |
177 | /* GP2 Timer Interrupt Acknowledge Register 32bit (-/W) */ | |
178 | #define U300_TIMER_APP_GPT2IA (0x00e0) | |
179 | #define U300_TIMER_APP_GPT2IA_IRQ_ACK (0x00000080) | |
180 | ||
181 | /* Clock request control register - all four timers */ | |
182 | #define U300_TIMER_APP_CRC (0x100) | |
183 | #define U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE (0x00000001) | |
184 | ||
185 | #define TICKS_PER_JIFFY ((CLOCK_TICK_RATE + (HZ/2)) / HZ) | |
186 | #define US_PER_TICK ((1000000 + (HZ/2)) / HZ) | |
187 | ||
188 | /* | |
189 | * The u300_set_mode() function is always called first, if we | |
190 | * have oneshot timer active, the oneshot scheduling function | |
191 | * u300_set_next_event() is called immediately after. | |
192 | */ | |
193 | static void u300_set_mode(enum clock_event_mode mode, | |
194 | struct clock_event_device *evt) | |
195 | { | |
196 | switch (mode) { | |
197 | case CLOCK_EVT_MODE_PERIODIC: | |
198 | /* Disable interrupts on GPT1 */ | |
199 | writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE, | |
200 | U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE); | |
201 | /* Disable GP1 while we're reprogramming it. */ | |
202 | writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE, | |
203 | U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1); | |
204 | /* | |
205 | * Set the periodic mode to a certain number of ticks per | |
206 | * jiffy. | |
207 | */ | |
208 | writel(TICKS_PER_JIFFY, | |
209 | U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1TC); | |
210 | /* | |
211 | * Set continuous mode, so the timer keeps triggering | |
212 | * interrupts. | |
213 | */ | |
214 | writel(U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS, | |
215 | U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT1M); | |
216 | /* Enable timer interrupts */ | |
217 | writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE, | |
218 | U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE); | |
219 | /* Then enable the OS timer again */ | |
220 | writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE, | |
221 | U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT1); | |
222 | break; | |
223 | case CLOCK_EVT_MODE_ONESHOT: | |
224 | /* Just break; here? */ | |
225 | /* | |
226 | * The actual event will be programmed by the next event hook, | |
227 | * so we just set a dummy value somewhere at the end of the | |
228 | * universe here. | |
229 | */ | |
230 | /* Disable interrupts on GPT1 */ | |
231 | writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE, | |
232 | U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE); | |
233 | /* Disable GP1 while we're reprogramming it. */ | |
234 | writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE, | |
235 | U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1); | |
236 | /* | |
237 | * Expire far in the future, u300_set_next_event() will be | |
238 | * called soon... | |
239 | */ | |
240 | writel(0xFFFFFFFF, U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1TC); | |
241 | /* We run one shot per tick here! */ | |
242 | writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT, | |
243 | U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT1M); | |
244 | /* Enable interrupts for this timer */ | |
245 | writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE, | |
246 | U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE); | |
247 | /* Enable timer */ | |
248 | writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE, | |
249 | U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT1); | |
250 | break; | |
251 | case CLOCK_EVT_MODE_UNUSED: | |
252 | case CLOCK_EVT_MODE_SHUTDOWN: | |
253 | /* Disable interrupts on GP1 */ | |
254 | writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE, | |
255 | U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE); | |
256 | /* Disable GP1 */ | |
257 | writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE, | |
258 | U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1); | |
259 | break; | |
260 | case CLOCK_EVT_MODE_RESUME: | |
261 | /* Ignore this call */ | |
262 | break; | |
263 | } | |
264 | } | |
265 | ||
266 | /* | |
267 | * The app timer in one shot mode obviously has to be reprogrammed | |
268 | * in EXACTLY this sequence to work properly. Do NOT try to e.g. replace | |
269 | * the interrupt disable + timer disable commands with a reset command, | |
270 | * it will fail miserably. Apparently (and I found this the hard way) | |
271 | * the timer is very sensitive to the instruction order, though you don't | |
272 | * get that impression from the data sheet. | |
273 | */ | |
274 | static int u300_set_next_event(unsigned long cycles, | |
275 | struct clock_event_device *evt) | |
276 | ||
277 | { | |
278 | /* Disable interrupts on GPT1 */ | |
279 | writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE, | |
280 | U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE); | |
281 | /* Disable GP1 while we're reprogramming it. */ | |
282 | writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE, | |
283 | U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1); | |
284 | /* Reset the General Purpose timer 1. */ | |
285 | writel(U300_TIMER_APP_RGPT1_TIMER_RESET, | |
286 | U300_TIMER_APP_VBASE + U300_TIMER_APP_RGPT1); | |
287 | /* IRQ in n * cycles */ | |
288 | writel(cycles, U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1TC); | |
289 | /* | |
290 | * We run one shot per tick here! (This is necessary to reconfigure, | |
291 | * the timer will tilt if you don't!) | |
292 | */ | |
293 | writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT, | |
294 | U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT1M); | |
295 | /* Enable timer interrupts */ | |
296 | writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE, | |
297 | U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE); | |
298 | /* Then enable the OS timer again */ | |
299 | writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE, | |
300 | U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT1); | |
301 | return 0; | |
302 | } | |
303 | ||
304 | ||
305 | /* Use general purpose timer 1 as clock event */ | |
306 | static struct clock_event_device clockevent_u300_1mhz = { | |
307 | .name = "GPT1", | |
308 | .rating = 300, /* Reasonably fast and accurate clock event */ | |
309 | .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT, | |
310 | /* 22 calculated using the algorithm in arch/mips/kernel/time.c */ | |
311 | .shift = 22, | |
312 | .set_next_event = u300_set_next_event, | |
313 | .set_mode = u300_set_mode, | |
314 | }; | |
315 | ||
316 | /* Clock event timer interrupt handler */ | |
317 | static irqreturn_t u300_timer_interrupt(int irq, void *dev_id) | |
318 | { | |
319 | struct clock_event_device *evt = &clockevent_u300_1mhz; | |
320 | /* ACK/Clear timer IRQ for the APP GPT1 Timer */ | |
321 | writel(U300_TIMER_APP_GPT1IA_IRQ_ACK, | |
322 | U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IA); | |
323 | evt->event_handler(evt); | |
324 | return IRQ_HANDLED; | |
325 | } | |
326 | ||
327 | static struct irqaction u300_timer_irq = { | |
328 | .name = "U300 Timer Tick", | |
329 | .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL, | |
330 | .handler = u300_timer_interrupt, | |
331 | }; | |
332 | ||
333 | /* Use general purpose timer 2 as clock source */ | |
b7c11ec9 | 334 | static cycle_t u300_get_cycles(struct clocksource *cs) |
bb3cee2b LW |
335 | { |
336 | return (cycles_t) readl(U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2CC); | |
337 | } | |
338 | ||
339 | static struct clocksource clocksource_u300_1mhz = { | |
340 | .name = "GPT2", | |
341 | .rating = 300, /* Reasonably fast and accurate clock source */ | |
342 | .read = u300_get_cycles, | |
343 | .mask = CLOCKSOURCE_MASK(32), /* 32 bits */ | |
344 | /* 22 calculated using the algorithm in arch/mips/kernel/time.c */ | |
345 | .shift = 22, | |
346 | .flags = CLOCK_SOURCE_IS_CONTINUOUS, | |
347 | }; | |
348 | ||
349 | ||
350 | /* | |
351 | * This sets up the system timers, clock source and clock event. | |
352 | */ | |
353 | static void __init u300_timer_init(void) | |
354 | { | |
355 | u300_enable_timer_clock(); | |
356 | /* | |
357 | * Disable the "OS" and "DD" timers - these are designed for Symbian! | |
358 | * Example usage in cnh1601578 cpu subsystem pd_timer_app.c | |
359 | */ | |
360 | writel(U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE, | |
361 | U300_TIMER_APP_VBASE + U300_TIMER_APP_CRC); | |
362 | writel(U300_TIMER_APP_ROST_TIMER_RESET, | |
363 | U300_TIMER_APP_VBASE + U300_TIMER_APP_ROST); | |
364 | writel(U300_TIMER_APP_DOST_TIMER_DISABLE, | |
365 | U300_TIMER_APP_VBASE + U300_TIMER_APP_DOST); | |
366 | writel(U300_TIMER_APP_RDDT_TIMER_RESET, | |
367 | U300_TIMER_APP_VBASE + U300_TIMER_APP_RDDT); | |
368 | writel(U300_TIMER_APP_DDDT_TIMER_DISABLE, | |
369 | U300_TIMER_APP_VBASE + U300_TIMER_APP_DDDT); | |
370 | ||
371 | /* Reset the General Purpose timer 1. */ | |
372 | writel(U300_TIMER_APP_RGPT1_TIMER_RESET, | |
373 | U300_TIMER_APP_VBASE + U300_TIMER_APP_RGPT1); | |
374 | ||
375 | /* Set up the IRQ handler */ | |
376 | setup_irq(IRQ_U300_TIMER_APP_GP1, &u300_timer_irq); | |
377 | ||
378 | /* Reset the General Purpose timer 2 */ | |
379 | writel(U300_TIMER_APP_RGPT2_TIMER_RESET, | |
380 | U300_TIMER_APP_VBASE + U300_TIMER_APP_RGPT2); | |
381 | /* Set this timer to run around forever */ | |
382 | writel(0xFFFFFFFFU, U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2TC); | |
383 | /* Set continuous mode so it wraps around */ | |
384 | writel(U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS, | |
385 | U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT2M); | |
386 | /* Disable timer interrupts */ | |
387 | writel(U300_TIMER_APP_GPT2IE_IRQ_DISABLE, | |
388 | U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2IE); | |
389 | /* Then enable the GP2 timer to use as a free running us counter */ | |
390 | writel(U300_TIMER_APP_EGPT2_TIMER_ENABLE, | |
391 | U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT2); | |
392 | ||
393 | /* This is a pure microsecond clock source */ | |
394 | clocksource_u300_1mhz.mult = | |
395 | clocksource_khz2mult(1000, clocksource_u300_1mhz.shift); | |
396 | if (clocksource_register(&clocksource_u300_1mhz)) | |
397 | printk(KERN_ERR "timer: failed to initialize clock " | |
398 | "source %s\n", clocksource_u300_1mhz.name); | |
399 | ||
400 | clockevent_u300_1mhz.mult = | |
401 | div_sc(1000000, NSEC_PER_SEC, clockevent_u300_1mhz.shift); | |
402 | /* 32bit counter, so 32bits delta is max */ | |
403 | clockevent_u300_1mhz.max_delta_ns = | |
404 | clockevent_delta2ns(0xffffffff, &clockevent_u300_1mhz); | |
405 | /* This timer is slow enough to set for 1 cycle == 1 MHz */ | |
406 | clockevent_u300_1mhz.min_delta_ns = | |
407 | clockevent_delta2ns(1, &clockevent_u300_1mhz); | |
408 | clockevent_u300_1mhz.cpumask = cpumask_of(0); | |
409 | clockevents_register_device(&clockevent_u300_1mhz); | |
410 | /* | |
411 | * TODO: init and register the rest of the timers too, they can be | |
412 | * used by hrtimers! | |
413 | */ | |
414 | } | |
415 | ||
416 | /* | |
417 | * Very simple system timer that only register the clock event and | |
418 | * clock source. | |
419 | */ | |
420 | struct sys_timer u300_timer = { | |
421 | .init = u300_timer_init, | |
422 | }; |