Commit | Line | Data |
---|---|---|
5e1c5ff4 TL |
1 | if ARCH_OMAP |
2 | ||
3 | menu "TI OMAP Implementations" | |
4 | ||
5 | config ARCH_OMAP_OTG | |
6 | bool | |
7 | ||
8 | choice | |
9 | prompt "OMAP System Type" | |
10 | default ARCH_OMAP1 | |
11 | ||
12 | config ARCH_OMAP1 | |
13 | bool "TI OMAP1" | |
14 | ||
15 | config ARCH_OMAP2 | |
16 | bool "TI OMAP2" | |
17 | ||
18 | endchoice | |
19 | ||
20 | comment "OMAP Feature Selections" | |
21 | ||
22 | config OMAP_MUX | |
23 | bool "OMAP multiplexing support" | |
24 | depends on ARCH_OMAP | |
25 | default y | |
26 | help | |
27 | Pin multiplexing support for OMAP boards. If your bootloader | |
28 | sets the multiplexing correctly, say N. Otherwise, or if unsure, | |
29 | say Y. | |
30 | ||
31 | config OMAP_MUX_DEBUG | |
32 | bool "Multiplexing debug output" | |
33 | depends on OMAP_MUX | |
34 | default n | |
35 | help | |
36 | Makes the multiplexing functions print out a lot of debug info. | |
37 | This is useful if you want to find out the correct values of the | |
38 | multiplexing registers. | |
39 | ||
40 | config OMAP_MUX_WARNINGS | |
41 | bool "Warn about pins the bootloader didn't set up" | |
42 | depends on OMAP_MUX | |
43 | default y | |
44 | help | |
45 | Choose Y here to warn whenever driver initialization logic needs | |
46 | to change the pin multiplexing setup. When there are no warnings | |
47 | printed, it's safe to deselect OMAP_MUX for your product. | |
48 | ||
49 | choice | |
50 | prompt "System timer" | |
51 | default OMAP_MPU_TIMER | |
52 | ||
53 | config OMAP_MPU_TIMER | |
54 | bool "Use mpu timer" | |
55 | help | |
56 | Select this option if you want to use the OMAP mpu timer. This | |
57 | timer provides more intra-tick resolution than the 32KHz timer, | |
58 | but consumes more power. | |
59 | ||
60 | config OMAP_32K_TIMER | |
61 | bool "Use 32KHz timer" | |
62 | depends on ARCH_OMAP16XX | |
63 | help | |
64 | Select this option if you want to enable the OMAP 32KHz timer. | |
65 | This timer saves power compared to the OMAP_MPU_TIMER, and has | |
66 | support for no tick during idle. The 32KHz timer provides less | |
67 | intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is | |
68 | currently only available for OMAP-16xx. | |
69 | ||
70 | endchoice | |
71 | ||
72 | config OMAP_32K_TIMER_HZ | |
73 | int "Kernel internal timer frequency for 32KHz timer" | |
74 | range 32 1024 | |
75 | depends on OMAP_32K_TIMER | |
76 | default "128" | |
77 | help | |
78 | Kernel internal timer frequency should be a divisor of 32768, | |
79 | such as 64 or 128. | |
80 | ||
81 | choice | |
82 | prompt "Low-level debug console UART" | |
83 | depends on ARCH_OMAP | |
84 | default OMAP_LL_DEBUG_UART1 | |
85 | ||
86 | config OMAP_LL_DEBUG_UART1 | |
87 | bool "UART1" | |
88 | ||
89 | config OMAP_LL_DEBUG_UART2 | |
90 | bool "UART2" | |
91 | ||
92 | config OMAP_LL_DEBUG_UART3 | |
93 | bool "UART3" | |
94 | ||
95 | endchoice | |
96 | ||
97 | endmenu | |
98 | ||
99 | endif |