[deliverable/linux.git] / arch / powerpc / boot / dts / p1025rdb.dtsi

/*
 * P1025 RDB Device Tree Source stub (no addresses or top-level ranges)
 *
 * Copyright 2011 Freescale Semiconductor Inc.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *     * Redistributions of source code must retain the above copyright
 *       notice, this list of conditions and the following disclaimer.
 *     * Redistributions in binary form must reproduce the above copyright
 *       notice, this list of conditions and the following disclaimer in the
 *       documentation and/or other materials provided with the distribution.
 *     * Neither the name of Freescale Semiconductor nor the
 *       names of its contributors may be used to endorse or promote products
 *       derived from this software without specific prior written permission.
 *
 *
 * ALTERNATIVELY, this software may be distributed under the terms of the
 * GNU General Public License ("GPL") as published by the Free Software
 * Foundation, either version 2 of that License or (at your option) any
 * later version.
 *
 * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
 * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
 * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
 * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
 * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

&lbc {
	nor@0,0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "cfi-flash";
		reg = <0x0 0x0 0x1000000>;
		bank-width = <2>;
		device-width = <1>;

		partition@0 {
			/* This location must not be altered  */
			/* 256KB for Vitesse 7385 Switch firmware */
			reg = <0x0 0x00040000>;
			label = "NOR Vitesse-7385 Firmware";
			read-only;
		};

		partition@40000 {
			/* 256KB for DTB Image */
			reg = <0x00040000 0x00040000>;
			label = "NOR DTB Image";
		};

		partition@80000 {
			/* 3.5 MB for Linux Kernel Image */
			reg = <0x00080000 0x00380000>;
			label = "NOR Linux Kernel Image";
		};

		partition@400000 {
			/* 11MB for JFFS2 based Root file System */
			reg = <0x00400000 0x00b00000>;
			label = "NOR JFFS2 Root File System";
		};

		partition@f00000 {
			/* This location must not be altered  */
			/* 512KB for u-boot Bootloader Image */
			/* 512KB for u-boot Environment Variables */
			reg = <0x00f00000 0x00100000>;
			label = "NOR U-Boot Image";
			read-only;
		};
	};

	nand@1,0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "fsl,p1025-fcm-nand",
			     "fsl,elbc-fcm-nand";
		reg = <0x1 0x0 0x40000>;

		partition@0 {
			/* This location must not be altered  */
			/* 1MB for u-boot Bootloader Image */
			reg = <0x0 0x00100000>;
			label = "NAND U-Boot Image";
			read-only;
		};

		partition@100000 {
			/* 1MB for DTB Image */
			reg = <0x00100000 0x00100000>;
			label = "NAND DTB Image";
		};

		partition@200000 {
			/* 4MB for Linux Kernel Image */
			reg = <0x00200000 0x00400000>;
			label = "NAND Linux Kernel Image";
		};

		partition@600000 {
			/* 4MB for Compressed Root file System Image */
			reg = <0x00600000 0x00400000>;
			label = "NAND Compressed RFS Image";
		};

		partition@a00000 {
			/* 7MB for JFFS2 based Root file System */
			reg = <0x00a00000 0x00700000>;
			label = "NAND JFFS2 Root File System";
		};

		partition@1100000 {
			/* 15MB for JFFS2 based Root file System */
			reg = <0x01100000 0x00f00000>;
			label = "NAND Writable User area";
		};
	};

};

&soc {
	i2c@3000 {
		rtc@68 {
			compatible = "dallas,ds1339";
			reg = <0x68>;
		};
	};

	spi@7000 {
		flash@0 {
			#address-cells = <1>;
			#size-cells = <1>;
			compatible = "spansion,s25sl12801";
			reg = <0>;
			spi-max-frequency = <40000000>; /* input clock */

			partition@u-boot {
				/* 512KB for u-boot Bootloader Image */
				reg = <0x0 0x00080000>;
				label = "u-boot";
				read-only;
			};

			partition@dtb {
				/* 512KB for DTB Image */
				reg = <0x00080000 0x00080000>;
				label = "dtb";
			};

			partition@kernel {
				/* 4MB for Linux Kernel Image */
				reg = <0x00100000 0x00400000>;
				label = "kernel";
			};

			partition@fs {
				/* 4MB for Compressed RFS Image */
				reg = <0x00500000 0x00400000>;
				label = "file system";
			};

			partition@jffs-fs {
				/* 7MB for JFFS2 based RFS */
				reg = <0x00900000 0x00700000>;
				label = "file system jffs2";
			};
		};
	};

	usb@22000 {
		phy_type = "ulpi";
	};

	/* USB2 is shared with localbus, so it must be disabled
	   by default. We can't put 'status = "disabled";' here
	   since U-Boot doesn't clear the status property when
	   it enables USB2. OTOH, U-Boot does create a new node
	   when there isn't any. So, just comment it out.
	usb@23000 {
		phy_type = "ulpi";
	};
	*/

	mdio@24000 {
		phy0: ethernet-phy@0 {
			interrupt-parent = <&mpic>;
			interrupts = <3 1>;
			reg = <0x0>;
		};

		phy1: ethernet-phy@1 {
			interrupt-parent = <&mpic>;
			interrupts = <2 1>;
			reg = <0x1>;
		};

		tbi0: tbi-phy@11 {
			reg = <0x11>;
			device_type = "tbi-phy";
		};
	};

	mdio@25000 {
		tbi1: tbi-phy@11 {
			reg = <0x11>;
			device_type = "tbi-phy";
		};
	};

	mdio@26000 {
		tbi2: tbi-phy@11 {
			reg = <0x11>;
			device_type = "tbi-phy";
		};
	};

	enet0: ethernet@b0000 {
		fixed-link = <1 1 1000 0 0>;
		phy-connection-type = "rgmii-id";

	};

	enet1: ethernet@b1000 {
		phy-handle = <&phy0>;
		tbi-handle = <&tbi1>;
		phy-connection-type = "sgmii";
	};

	enet2: ethernet@b2000 {
		phy-handle = <&phy1>;
		phy-connection-type = "rgmii-id";
	};

	par_io@e0100 {
		#address-cells = <1>;
		#size-cells = <1>;
		reg = <0xe0100 0x60>;
		ranges = <0x0 0xe0100 0x60>;
		device_type = "par_io";
		num-ports = <3>;
		pio1: ucc_pin@01 {
			pio-map = <
		/* port  pin  dir  open_drain  assignment  has_irq */
				0x1  0x13 0x1  0x0  0x1  0x0    /* QE_MUX_MDC */
				0x1  0x14 0x3  0x0  0x1  0x0    /* QE_MUX_MDIO */
				0x0  0x17 0x2  0x0  0x2  0x0    /* CLK12 */
				0x0  0x18 0x2  0x0  0x1  0x0    /* CLK9 */
				0x0  0x7  0x1  0x0  0x2  0x0    /* ENET1_TXD0_SER1_TXD0 */
				0x0  0x9  0x1  0x0  0x2  0x0    /* ENET1_TXD1_SER1_TXD1 */
				0x0  0xb  0x1  0x0  0x2  0x0    /* ENET1_TXD2_SER1_TXD2 */
				0x0  0xc  0x1  0x0  0x2  0x0    /* ENET1_TXD3_SER1_TXD3 */
				0x0  0x6  0x2  0x0  0x2  0x0    /* ENET1_RXD0_SER1_RXD0 */
				0x0  0xa  0x2  0x0  0x2  0x0    /* ENET1_RXD1_SER1_RXD1 */
				0x0  0xe  0x2  0x0  0x2  0x0    /* ENET1_RXD2_SER1_RXD2 */
				0x0  0xf  0x2  0x0  0x2  0x0    /* ENET1_RXD3_SER1_RXD3 */
				0x0  0x5  0x1  0x0  0x2  0x0    /* ENET1_TX_EN_SER1_RTS_B */
				0x0  0xd  0x1  0x0  0x2  0x0    /* ENET1_TX_ER */
				0x0  0x4  0x2  0x0  0x2  0x0    /* ENET1_RX_DV_SER1_CTS_B */
				0x0  0x8  0x2  0x0  0x2  0x0    /* ENET1_RX_ER_SER1_CD_B */
				0x0  0x11 0x2  0x0  0x2  0x0    /* ENET1_CRS */
				0x0  0x10 0x2  0x0  0x2  0x0>;    /* ENET1_COL */
		};

		pio2: ucc_pin@02 {
			pio-map = <
		/* port  pin  dir  open_drain  assignment  has_irq */
				0x1  0x13 0x1  0x0  0x1  0x0    /* QE_MUX_MDC */
				0x1  0x14 0x3  0x0  0x1  0x0    /* QE_MUX_MDIO */
				0x1  0xb  0x2  0x0  0x1  0x0    /* CLK13 */
				0x1  0x7  0x1  0x0  0x2  0x0    /* ENET5_TXD0_SER5_TXD0 */
				0x1  0xa  0x1  0x0  0x2  0x0    /* ENET5_TXD1_SER5_TXD1 */
				0x1  0x6  0x2  0x0  0x2  0x0    /* ENET5_RXD0_SER5_RXD0 */
				0x1  0x9  0x2  0x0  0x2  0x0    /* ENET5_RXD1_SER5_RXD1 */
				0x1  0x5  0x1  0x0  0x2  0x0    /* ENET5_TX_EN_SER5_RTS_B */
				0x1  0x4  0x2  0x0  0x2  0x0    /* ENET5_RX_DV_SER5_CTS_B */
				0x1  0x8  0x2  0x0  0x2  0x0>;    /* ENET5_RX_ER_SER5_CD_B */
		};

		pio3: ucc_pin@03 {
			pio-map = <
		/* port  pin  dir  open_drain  assignment  has_irq */
				0x0  0x16 0x2  0x0  0x2  0x0    /* SER7_CD_B*/
				0x0  0x12 0x2  0x0  0x2  0x0    /* SER7_CTS_B*/
				0x0  0x13 0x1  0x0  0x2  0x0    /* SER7_RTS_B*/
				0x0  0x14 0x2  0x0  0x2  0x0    /* SER7_RXD0*/
				0x0  0x15 0x1  0x0  0x2  0x0>;    /* SER7_TXD0*/
		};

		pio4: ucc_pin@04 {
			pio-map = <
		/* port  pin  dir  open_drain  assignment  has_irq */
				0x1  0x0  0x2  0x0  0x2  0x0    /* SER3_CD_B*/
				0x0  0x1c 0x2  0x0  0x2  0x0    /* SER3_CTS_B*/
				0x0  0x1d 0x1  0x0  0x2  0x0    /* SER3_RTS_B*/
				0x0  0x1e 0x2  0x0  0x2  0x0    /* SER3_RXD0*/
				0x0  0x1f 0x1  0x0  0x2  0x0>;    /* SER3_TXD0*/
		};
	};
};

&qe {
	serial2: ucc@2600 {
		device_type = "serial";
		compatible = "ucc_uart";
		port-number = <0>;
		rx-clock-name = "brg6";
		tx-clock-name = "brg6";
		pio-handle = <&pio3>;
	};

	serial3: ucc@2200 {
		device_type = "serial";
		compatible = "ucc_uart";
		port-number = <1>;
		rx-clock-name = "brg2";
		tx-clock-name = "brg2";
		pio-handle = <&pio4>;
	};
};
Commit	Line	Data
79ad5740 ZF	1	/*
	2	* P1025 RDB Device Tree Source stub (no addresses or top-level ranges)
	3	*
	4	* Copyright 2011 Freescale Semiconductor Inc.
	5	*
	6	* Redistribution and use in source and binary forms, with or without
	7	* modification, are permitted provided that the following conditions are met:
	8	* * Redistributions of source code must retain the above copyright
	9	* notice, this list of conditions and the following disclaimer.
	10	* * Redistributions in binary form must reproduce the above copyright
	11	* notice, this list of conditions and the following disclaimer in the
	12	* documentation and/or other materials provided with the distribution.
	13	* * Neither the name of Freescale Semiconductor nor the
	14	* names of its contributors may be used to endorse or promote products
	15	* derived from this software without specific prior written permission.
	16	*
	17	*
	18	* ALTERNATIVELY, this software may be distributed under the terms of the
	19	* GNU General Public License ("GPL") as published by the Free Software
	20	* Foundation, either version 2 of that License or (at your option) any
	21	* later version.
	22	*
	23	* THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
	24	* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
	25	* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
	26	* DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
	27	* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
	28	* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
	29	* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
	30	* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
	31	* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
	32	* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
	33	*/
	34
	35	&lbc {
	36	nor@0,0 {
	37	#address-cells = <1>;
	38	#size-cells = <1>;
	39	compatible = "cfi-flash";
	40	reg = <0x0 0x0 0x1000000>;
	41	bank-width = <2>;
	42	device-width = <1>;
	43
	44	partition@0 {
	45	/* This location must not be altered */
	46	/* 256KB for Vitesse 7385 Switch firmware */
	47	reg = <0x0 0x00040000>;
	48	label = "NOR Vitesse-7385 Firmware";
	49	read-only;
	50	};
	51
	52	partition@40000 {
	53	/* 256KB for DTB Image */
	54	reg = <0x00040000 0x00040000>;
	55	label = "NOR DTB Image";
	56	};
	57
	58	partition@80000 {
	59	/* 3.5 MB for Linux Kernel Image */
	60	reg = <0x00080000 0x00380000>;
	61	label = "NOR Linux Kernel Image";
	62	};
	63
	64	partition@400000 {
65	/* 11MB for JFFS2 based Root file System */
66	reg = <0x00400000 0x00b00000>;
67	label = "NOR JFFS2 Root File System";
68	};
69
70	partition@f00000 {
71	/* This location must not be altered */
72	/* 512KB for u-boot Bootloader Image */
73	/* 512KB for u-boot Environment Variables */
74	reg = <0x00f00000 0x00100000>;
75	label = "NOR U-Boot Image";
76	read-only;
77	};
78	};
79
80	nand@1,0 {
81	#address-cells = <1>;
82	#size-cells = <1>;
83	compatible = "fsl,p1025-fcm-nand",
84	"fsl,elbc-fcm-nand";
85	reg = <0x1 0x0 0x40000>;
86
87	partition@0 {
88	/* This location must not be altered */
89	/* 1MB for u-boot Bootloader Image */
90	reg = <0x0 0x00100000>;
91	label = "NAND U-Boot Image";
92	read-only;
93	};
94
95	partition@100000 {
96	/* 1MB for DTB Image */
97	reg = <0x00100000 0x00100000>;
98	label = "NAND DTB Image";
99	};
100
101	partition@200000 {
102	/* 4MB for Linux Kernel Image */
103	reg = <0x00200000 0x00400000>;
104	label = "NAND Linux Kernel Image";
105	};
106
107	partition@600000 {
108	/* 4MB for Compressed Root file System Image */
109	reg = <0x00600000 0x00400000>;
110	label = "NAND Compressed RFS Image";
111	};
112
113	partition@a00000 {
114	/* 7MB for JFFS2 based Root file System */
115	reg = <0x00a00000 0x00700000>;
116	label = "NAND JFFS2 Root File System";
117	};
118
119	partition@1100000 {
120	/* 15MB for JFFS2 based Root file System */
121	reg = <0x01100000 0x00f00000>;
122	label = "NAND Writable User area";
123	};
124	};
125
126	};
127
128	&soc {
129	i2c@3000 {
130	rtc@68 {
131	compatible = "dallas,ds1339";
132	reg = <0x68>;
133	};
134	};
135
136	spi@7000 {
137	flash@0 {
138	#address-cells = <1>;
139	#size-cells = <1>;
140	compatible = "spansion,s25sl12801";
141	reg = <0>;
142	spi-max-frequency = <40000000>; /* input clock */
143
144	partition@u-boot {
145	/* 512KB for u-boot Bootloader Image */
146	reg = <0x0 0x00080000>;
147	label = "u-boot";
148	read-only;
149	};
150
151	partition@dtb {
152	/* 512KB for DTB Image */
153	reg = <0x00080000 0x00080000>;
154	label = "dtb";
155	};
156
157	partition@kernel {
158	/* 4MB for Linux Kernel Image */
159	reg = <0x00100000 0x00400000>;
160	label = "kernel";
161	};
162
163	partition@fs {
164	/* 4MB for Compressed RFS Image */
165	reg = <0x00500000 0x00400000>;
166	label = "file system";
167	};
168
169	partition@jffs-fs {
170	/* 7MB for JFFS2 based RFS */
171	reg = <0x00900000 0x00700000>;
172	label = "file system jffs2";
173	};
174	};
175	};
176
177	usb@22000 {
178	phy_type = "ulpi";
179	};
180
181	/* USB2 is shared with localbus, so it must be disabled
182	by default. We can't put 'status = "disabled";' here
183	since U-Boot doesn't clear the status property when
184	it enables USB2. OTOH, U-Boot does create a new node
185	when there isn't any. So, just comment it out.
186	usb@23000 {
187	phy_type = "ulpi";
188	};
189	*/
190
191	mdio@24000 {
192	phy0: ethernet-phy@0 {
193	interrupt-parent = <&mpic>;
194	interrupts = <3 1>;
195	reg = <0x0>;
196	};
197
198	phy1: ethernet-phy@1 {
199	interrupt-parent = <&mpic>;
200	interrupts = <2 1>;
201	reg = <0x1>;
202	};
203
204	tbi0: tbi-phy@11 {
205	reg = <0x11>;
206	device_type = "tbi-phy";
207	};
208	};
209
210	mdio@25000 {
211	tbi1: tbi-phy@11 {
212	reg = <0x11>;
213	device_type = "tbi-phy";
214	};
215	};
216
217	mdio@26000 {
218	tbi2: tbi-phy@11 {
219	reg = <0x11>;
220	device_type = "tbi-phy";
221	};
222	};
223
224	enet0: ethernet@b0000 {
225	fixed-link = <1 1 1000 0 0>;
226	phy-connection-type = "rgmii-id";
227
228	};
229
230	enet1: ethernet@b1000 {
231	phy-handle = <&phy0>;
232	tbi-handle = <&tbi1>;
233	phy-connection-type = "sgmii";
234	};
235
236	enet2: ethernet@b2000 {
237	phy-handle = <&phy1>;
238	phy-connection-type = "rgmii-id";
239	};
240
241	par_io@e0100 {
242	#address-cells = <1>;
243	#size-cells = <1>;
244	reg = <0xe0100 0x60>;
245	ranges = <0x0 0xe0100 0x60>;
246	device_type = "par_io";
247	num-ports = <3>;
248	pio1: ucc_pin@01 {
249	pio-map = <
250	/* port pin dir open_drain assignment has_irq */
251	0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
252	0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
253	0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */
254	0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9 */
255	0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */
256	0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */
257	0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */
258	0x0 0xc 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */
259	0x0 0x6 0x2 0x0 0x2 0x0 /* ENET1_RXD0_SER1_RXD0 */
260	0x0 0xa 0x2 0x0 0x2 0x0 /* ENET1_RXD1_SER1_RXD1 */
261	0x0 0xe 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */
262	0x0 0xf 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */
263	0x0 0x5 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */
264	0x0 0xd 0x1 0x0 0x2 0x0 /* ENET1_TX_ER */
265	0x0 0x4 0x2 0x0 0x2 0x0 /* ENET1_RX_DV_SER1_CTS_B */
266	0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RX_ER_SER1_CD_B */
267	0x0 0x11 0x2 0x0 0x2 0x0 /* ENET1_CRS */
268	0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */
269	};
270
271	pio2: ucc_pin@02 {
272	pio-map = <
273	/* port pin dir open_drain assignment has_irq */
274	0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
275	0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
276	0x1 0xb 0x2 0x0 0x1 0x0 /* CLK13 */
277	0x1 0x7 0x1 0x0 0x2 0x0 /* ENET5_TXD0_SER5_TXD0 */
278	0x1 0xa 0x1 0x0 0x2 0x0 /* ENET5_TXD1_SER5_TXD1 */
279	0x1 0x6 0x2 0x0 0x2 0x0 /* ENET5_RXD0_SER5_RXD0 */
280	0x1 0x9 0x2 0x0 0x2 0x0 /* ENET5_RXD1_SER5_RXD1 */
281	0x1 0x5 0x1 0x0 0x2 0x0 /* ENET5_TX_EN_SER5_RTS_B */
282	0x1 0x4 0x2 0x0 0x2 0x0 /* ENET5_RX_DV_SER5_CTS_B */
283	0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */
284	};
b5dc2986 ZF	285
	286	pio3: ucc_pin@03 {
	287	pio-map = <
	288	/* port pin dir open_drain assignment has_irq */
	289	0x0 0x16 0x2 0x0 0x2 0x0 /* SER7_CD_B*/
	290	0x0 0x12 0x2 0x0 0x2 0x0 /* SER7_CTS_B*/
	291	0x0 0x13 0x1 0x0 0x2 0x0 /* SER7_RTS_B*/
	292	0x0 0x14 0x2 0x0 0x2 0x0 /* SER7_RXD0*/
	293	0x0 0x15 0x1 0x0 0x2 0x0>; /* SER7_TXD0*/
	294	};
	295
	296	pio4: ucc_pin@04 {
	297	pio-map = <
	298	/* port pin dir open_drain assignment has_irq */
	299	0x1 0x0 0x2 0x0 0x2 0x0 /* SER3_CD_B*/
	300	0x0 0x1c 0x2 0x0 0x2 0x0 /* SER3_CTS_B*/
	301	0x0 0x1d 0x1 0x0 0x2 0x0 /* SER3_RTS_B*/
	302	0x0 0x1e 0x2 0x0 0x2 0x0 /* SER3_RXD0*/
	303	0x0 0x1f 0x1 0x0 0x2 0x0>; /* SER3_TXD0*/
	304	};
	305	};
	306	};
	307
	308	&qe {
	309	serial2: ucc@2600 {
	310	device_type = "serial";
	311	compatible = "ucc_uart";
	312	port-number = <0>;
	313	rx-clock-name = "brg6";
	314	tx-clock-name = "brg6";
	315	pio-handle = <&pio3>;
	316	};
	317
	318	serial3: ucc@2200 {
	319	device_type = "serial";
	320	compatible = "ucc_uart";
	321	port-number = <1>;
	322	rx-clock-name = "brg2";
	323	tx-clock-name = "brg2";
	324	pio-handle = <&pio4>;
79ad5740 ZF	325	};
79ad5740 ZF	326	};