Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /*---------------------------------------------------------------------------+ |
2 | | fpu_system.h | | |
3 | | | | |
4 | | Copyright (C) 1992,1994,1997 | | |
5 | | W. Metzenthen, 22 Parker St, Ormond, Vic 3163, | | |
6 | | Australia. E-mail billm@suburbia.net | | |
7 | | | | |
8 | +---------------------------------------------------------------------------*/ | |
9 | ||
10 | #ifndef _FPU_SYSTEM_H | |
11 | #define _FPU_SYSTEM_H | |
12 | ||
13 | /* system dependent definitions */ | |
14 | ||
15 | #include <linux/sched.h> | |
16 | #include <linux/kernel.h> | |
17 | #include <linux/mm.h> | |
18 | ||
1da177e4 LT |
19 | /* s is always from a cpu register, and the cpu does bounds checking |
20 | * during register load --> no further bounds checks needed */ | |
21 | #define LDT_DESCRIPTOR(s) (((struct desc_struct *)current->mm->context.ldt)[(s) >> 3]) | |
22 | #define SEG_D_SIZE(x) ((x).b & (3 << 21)) | |
23 | #define SEG_G_BIT(x) ((x).b & (1 << 23)) | |
24 | #define SEG_GRANULARITY(x) (((x).b & (1 << 23)) ? 4096 : 1) | |
25 | #define SEG_286_MODE(x) ((x).b & ( 0xff000000 | 0xf0000 | (1 << 23))) | |
26 | #define SEG_BASE_ADDR(s) (((s).b & 0xff000000) \ | |
27 | | (((s).b & 0xff) << 16) | ((s).a >> 16)) | |
28 | #define SEG_LIMIT(s) (((s).b & 0xff0000) | ((s).a & 0xffff)) | |
29 | #define SEG_EXECUTE_ONLY(s) (((s).b & ((1 << 11) | (1 << 9))) == (1 << 11)) | |
30 | #define SEG_WRITE_PERM(s) (((s).b & ((1 << 11) | (1 << 9))) == (1 << 9)) | |
31 | #define SEG_EXPAND_DOWN(s) (((s).b & ((1 << 11) | (1 << 10))) \ | |
32 | == (1 << 10)) | |
33 | ||
c3f8978e | 34 | #define I387 (current->thread.fpu.state) |
61c4628b | 35 | #define FPU_info (I387->soft.info) |
1da177e4 | 36 | |
d315760f TH |
37 | #define FPU_CS (*(unsigned short *) &(FPU_info->regs->cs)) |
38 | #define FPU_SS (*(unsigned short *) &(FPU_info->regs->ss)) | |
39 | #define FPU_DS (*(unsigned short *) &(FPU_info->regs->ds)) | |
40 | #define FPU_EAX (FPU_info->regs->ax) | |
41 | #define FPU_EFLAGS (FPU_info->regs->flags) | |
42 | #define FPU_EIP (FPU_info->regs->ip) | |
1da177e4 LT |
43 | #define FPU_ORIG_EIP (FPU_info->___orig_eip) |
44 | ||
61c4628b | 45 | #define FPU_lookahead (I387->soft.lookahead) |
1da177e4 LT |
46 | |
47 | /* nz if ip_offset and cs_selector are not to be set for the current | |
48 | instruction. */ | |
61c4628b SS |
49 | #define no_ip_update (*(u_char *)&(I387->soft.no_update)) |
50 | #define FPU_rm (*(u_char *)&(I387->soft.rm)) | |
1da177e4 LT |
51 | |
52 | /* Number of bytes of data which can be legally accessed by the current | |
53 | instruction. This only needs to hold a number <= 108, so a byte will do. */ | |
61c4628b | 54 | #define access_limit (*(u_char *)&(I387->soft.alimit)) |
1da177e4 | 55 | |
61c4628b SS |
56 | #define partial_status (I387->soft.swd) |
57 | #define control_word (I387->soft.cwd) | |
58 | #define fpu_tag_word (I387->soft.twd) | |
59 | #define registers (I387->soft.st_space) | |
60 | #define top (I387->soft.ftop) | |
1da177e4 | 61 | |
61c4628b SS |
62 | #define instruction_address (*(struct address *)&I387->soft.fip) |
63 | #define operand_address (*(struct address *)&I387->soft.foo) | |
1da177e4 LT |
64 | |
65 | #define FPU_access_ok(x,y,z) if ( !access_ok(x,y,z) ) \ | |
66 | math_abort(FPU_info,SIGSEGV) | |
d606f88f | 67 | #define FPU_abort math_abort(FPU_info, SIGSEGV) |
1da177e4 LT |
68 | |
69 | #undef FPU_IGNORE_CODE_SEGV | |
70 | #ifdef FPU_IGNORE_CODE_SEGV | |
71 | /* access_ok() is very expensive, and causes the emulator to run | |
72 | about 20% slower if applied to the code. Anyway, errors due to bad | |
73 | code addresses should be much rarer than errors due to bad data | |
74 | addresses. */ | |
75 | #define FPU_code_access_ok(z) | |
76 | #else | |
77 | /* A simpler test than access_ok() can probably be done for | |
78 | FPU_code_access_ok() because the only possible error is to step | |
79 | past the upper boundary of a legal code area. */ | |
80 | #define FPU_code_access_ok(z) FPU_access_ok(VERIFY_READ,(void __user *)FPU_EIP,z) | |
81 | #endif | |
82 | ||
83 | #define FPU_get_user(x,y) get_user((x),(y)) | |
84 | #define FPU_put_user(x,y) put_user((x),(y)) | |
85 | ||
86 | #endif |