[deliverable/linux.git] / drivers / hwmon / lm92.c

/*
 * lm92 - Hardware monitoring driver
 * Copyright (C) 2005-2008  Jean Delvare <khali@linux-fr.org>
 *
 * Based on the lm90 driver, with some ideas taken from the lm_sensors
 * lm92 driver as well.
 *
 * The LM92 is a sensor chip made by National Semiconductor. It reports
 * its own temperature with a 0.0625 deg resolution and a 0.33 deg
 * accuracy. Complete datasheet can be obtained from National's website
 * at:
 *   http://www.national.com/pf/LM/LM92.html
 *
 * This driver also supports the MAX6635 sensor chip made by Maxim.
 * This chip is compatible with the LM92, but has a lesser accuracy
 * (1.0 deg). Complete datasheet can be obtained from Maxim's website
 * at:
 *   http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3074
 *
 * Since the LM92 was the first chipset supported by this driver, most
 * comments will refer to this chipset, but are actually general and
 * concern all supported chipsets, unless mentioned otherwise.
 *
 * Support could easily be added for the National Semiconductor LM76
 * and Maxim MAX6633 and MAX6634 chips, which are mostly compatible
 * with the LM92.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>

/*
 * The LM92 and MAX6635 have 2 two-state pins for address selection,
 * resulting in 4 possible addresses.
 */
static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b,
						I2C_CLIENT_END };

/* The LM92 registers */
#define LM92_REG_CONFIG			0x01 /* 8-bit, RW */
#define LM92_REG_TEMP			0x00 /* 16-bit, RO */
#define LM92_REG_TEMP_HYST		0x02 /* 16-bit, RW */
#define LM92_REG_TEMP_CRIT		0x03 /* 16-bit, RW */
#define LM92_REG_TEMP_LOW		0x04 /* 16-bit, RW */
#define LM92_REG_TEMP_HIGH		0x05 /* 16-bit, RW */
#define LM92_REG_MAN_ID			0x07 /* 16-bit, RO, LM92 only */

/*
 * The LM92 uses signed 13-bit values with LSB = 0.0625 degree Celsius,
 * left-justified in 16-bit registers. No rounding is done, with such
 * a resolution it's just not worth it. Note that the MAX6635 doesn't
 * make use of the 4 lower bits for limits (i.e. effective resolution
 * for limits is 1 degree Celsius).
 */
static inline int TEMP_FROM_REG(s16 reg)
{
	return reg / 8 * 625 / 10;
}

static inline s16 TEMP_TO_REG(int val)
{
	if (val <= -60000)
		return -60000 * 10 / 625 * 8;
	if (val >= 160000)
		return 160000 * 10 / 625 * 8;
	return val * 10 / 625 * 8;
}

/* Alarm flags are stored in the 3 LSB of the temperature register */
static inline u8 ALARMS_FROM_REG(s16 reg)
{
	return reg & 0x0007;
}

/* Driver data (common to all clients) */
static struct i2c_driver lm92_driver;

/* Client data (each client gets its own) */
struct lm92_data {
	struct device *hwmon_dev;
	struct mutex update_lock;
	char valid; /* zero until following fields are valid */
	unsigned long last_updated; /* in jiffies */

	/* registers values */
	s16 temp1_input, temp1_crit, temp1_min, temp1_max, temp1_hyst;
};


/*
 * Sysfs attributes and callback functions
 */

static struct lm92_data *lm92_update_device(struct device *dev)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct lm92_data *data = i2c_get_clientdata(client);

	mutex_lock(&data->update_lock);

	if (time_after(jiffies, data->last_updated + HZ)
	 || !data->valid) {
		dev_dbg(&client->dev, "Updating lm92 data\n");
		data->temp1_input = i2c_smbus_read_word_swapped(client,
				    LM92_REG_TEMP);
		data->temp1_hyst = i2c_smbus_read_word_swapped(client,
				    LM92_REG_TEMP_HYST);
		data->temp1_crit = i2c_smbus_read_word_swapped(client,
				    LM92_REG_TEMP_CRIT);
		data->temp1_min = i2c_smbus_read_word_swapped(client,
				    LM92_REG_TEMP_LOW);
		data->temp1_max = i2c_smbus_read_word_swapped(client,
				    LM92_REG_TEMP_HIGH);

		data->last_updated = jiffies;
		data->valid = 1;
	}

	mutex_unlock(&data->update_lock);

	return data;
}

#define show_temp(value) \
static ssize_t show_##value(struct device *dev, struct device_attribute *attr, \
			    char *buf) \
{ \
	struct lm92_data *data = lm92_update_device(dev); \
	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->value)); \
}
show_temp(temp1_input);
show_temp(temp1_crit);
show_temp(temp1_min);
show_temp(temp1_max);

#define set_temp(value, reg) \
static ssize_t set_##value(struct device *dev, struct device_attribute *attr, \
			   const char *buf, \
	size_t count) \
{ \
	struct i2c_client *client = to_i2c_client(dev); \
	struct lm92_data *data = i2c_get_clientdata(client); \
	long val; \
	int err = kstrtol(buf, 10, &val); \
	if (err) \
		return err; \
\
	mutex_lock(&data->update_lock); \
	data->value = TEMP_TO_REG(val); \
	i2c_smbus_write_word_swapped(client, reg, data->value); \
	mutex_unlock(&data->update_lock); \
	return count; \
}
set_temp(temp1_crit, LM92_REG_TEMP_CRIT);
set_temp(temp1_min, LM92_REG_TEMP_LOW);
set_temp(temp1_max, LM92_REG_TEMP_HIGH);

static ssize_t show_temp1_crit_hyst(struct device *dev,
				    struct device_attribute *attr, char *buf)
{
	struct lm92_data *data = lm92_update_device(dev);
	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp1_crit)
		       - TEMP_FROM_REG(data->temp1_hyst));
}
static ssize_t show_temp1_max_hyst(struct device *dev,
				   struct device_attribute *attr, char *buf)
{
	struct lm92_data *data = lm92_update_device(dev);
	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp1_max)
		       - TEMP_FROM_REG(data->temp1_hyst));
}
static ssize_t show_temp1_min_hyst(struct device *dev,
				   struct device_attribute *attr, char *buf)
{
	struct lm92_data *data = lm92_update_device(dev);
	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp1_min)
		       + TEMP_FROM_REG(data->temp1_hyst));
}

static ssize_t set_temp1_crit_hyst(struct device *dev,
				   struct device_attribute *attr,
				   const char *buf, size_t count)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct lm92_data *data = i2c_get_clientdata(client);
	long val;
	int err;

	err = kstrtol(buf, 10, &val);
	if (err)
		return err;

	mutex_lock(&data->update_lock);
	data->temp1_hyst = TEMP_FROM_REG(data->temp1_crit) - val;
	i2c_smbus_write_word_swapped(client, LM92_REG_TEMP_HYST,
				     TEMP_TO_REG(data->temp1_hyst));
	mutex_unlock(&data->update_lock);
	return count;
}

static ssize_t show_alarms(struct device *dev, struct device_attribute *attr,
			   char *buf)
{
	struct lm92_data *data = lm92_update_device(dev);
	return sprintf(buf, "%d\n", ALARMS_FROM_REG(data->temp1_input));
}

static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
			  char *buf)
{
	int bitnr = to_sensor_dev_attr(attr)->index;
	struct lm92_data *data = lm92_update_device(dev);
	return sprintf(buf, "%d\n", (data->temp1_input >> bitnr) & 1);
}

static DEVICE_ATTR(temp1_input, S_IRUGO, show_temp1_input, NULL);
static DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO, show_temp1_crit,
	set_temp1_crit);
static DEVICE_ATTR(temp1_crit_hyst, S_IWUSR | S_IRUGO, show_temp1_crit_hyst,
	set_temp1_crit_hyst);
static DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, show_temp1_min,
	set_temp1_min);
static DEVICE_ATTR(temp1_min_hyst, S_IRUGO, show_temp1_min_hyst, NULL);
static DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp1_max,
	set_temp1_max);
static DEVICE_ATTR(temp1_max_hyst, S_IRUGO, show_temp1_max_hyst, NULL);
static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 2);
static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL, 0);
static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 1);


/*
 * Detection and registration
 */

static void lm92_init_client(struct i2c_client *client)
{
	u8 config;

	/* Start the conversions if needed */
	config = i2c_smbus_read_byte_data(client, LM92_REG_CONFIG);
	if (config & 0x01)
		i2c_smbus_write_byte_data(client, LM92_REG_CONFIG,
					  config & 0xFE);
}

/*
 * The MAX6635 has no identification register, so we have to use tricks
 * to identify it reliably. This is somewhat slow.
 * Note that we do NOT rely on the 2 MSB of the configuration register
 * always reading 0, as suggested by the datasheet, because it was once
 * reported not to be true.
 */
static int max6635_check(struct i2c_client *client)
{
	u16 temp_low, temp_high, temp_hyst, temp_crit;
	u8 conf;
	int i;

	/*
	 * No manufacturer ID register, so a read from this address will
	 * always return the last read value.
	 */
	temp_low = i2c_smbus_read_word_data(client, LM92_REG_TEMP_LOW);
	if (i2c_smbus_read_word_data(client, LM92_REG_MAN_ID) != temp_low)
		return 0;
	temp_high = i2c_smbus_read_word_data(client, LM92_REG_TEMP_HIGH);
	if (i2c_smbus_read_word_data(client, LM92_REG_MAN_ID) != temp_high)
		return 0;

	/* Limits are stored as integer values (signed, 9-bit). */
	if ((temp_low & 0x7f00) || (temp_high & 0x7f00))
		return 0;
	temp_hyst = i2c_smbus_read_word_data(client, LM92_REG_TEMP_HYST);
	temp_crit = i2c_smbus_read_word_data(client, LM92_REG_TEMP_CRIT);
	if ((temp_hyst & 0x7f00) || (temp_crit & 0x7f00))
		return 0;

	/*
	 * Registers addresses were found to cycle over 16-byte boundaries.
	 * We don't test all registers with all offsets so as to save some
	 * reads and time, but this should still be sufficient to dismiss
	 * non-MAX6635 chips.
	 */
	conf = i2c_smbus_read_byte_data(client, LM92_REG_CONFIG);
	for (i = 16; i < 96; i *= 2) {
		if (temp_hyst != i2c_smbus_read_word_data(client,
				 LM92_REG_TEMP_HYST + i - 16)
		 || temp_crit != i2c_smbus_read_word_data(client,
				 LM92_REG_TEMP_CRIT + i)
		 || temp_low != i2c_smbus_read_word_data(client,
				LM92_REG_TEMP_LOW + i + 16)
		 || temp_high != i2c_smbus_read_word_data(client,
				 LM92_REG_TEMP_HIGH + i + 32)
		 || conf != i2c_smbus_read_byte_data(client,
			    LM92_REG_CONFIG + i))
			return 0;
	}

	return 1;
}

static struct attribute *lm92_attributes[] = {
	&dev_attr_temp1_input.attr,
	&dev_attr_temp1_crit.attr,
	&dev_attr_temp1_crit_hyst.attr,
	&dev_attr_temp1_min.attr,
	&dev_attr_temp1_min_hyst.attr,
	&dev_attr_temp1_max.attr,
	&dev_attr_temp1_max_hyst.attr,
	&dev_attr_alarms.attr,
	&sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
	&sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
	&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
	NULL
};

static const struct attribute_group lm92_group = {
	.attrs = lm92_attributes,
};

/* Return 0 if detection is successful, -ENODEV otherwise */
static int lm92_detect(struct i2c_client *new_client,
		       struct i2c_board_info *info)
{
	struct i2c_adapter *adapter = new_client->adapter;
	u8 config;
	u16 man_id;

	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA
					    | I2C_FUNC_SMBUS_WORD_DATA))
		return -ENODEV;

	config = i2c_smbus_read_byte_data(new_client, LM92_REG_CONFIG);
	man_id = i2c_smbus_read_word_data(new_client, LM92_REG_MAN_ID);

	if ((config & 0xe0) == 0x00 && man_id == 0x0180)
		pr_info("lm92: Found National Semiconductor LM92 chip\n");
	else if (max6635_check(new_client))
		pr_info("lm92: Found Maxim MAX6635 chip\n");
	else
		return -ENODEV;

	strlcpy(info->type, "lm92", I2C_NAME_SIZE);

	return 0;
}

static int lm92_probe(struct i2c_client *new_client,
		      const struct i2c_device_id *id)
{
	struct lm92_data *data;
	int err;

	data = devm_kzalloc(&new_client->dev, sizeof(struct lm92_data),
			    GFP_KERNEL);
	if (!data)
		return -ENOMEM;

	i2c_set_clientdata(new_client, data);
	data->valid = 0;
	mutex_init(&data->update_lock);

	/* Initialize the chipset */
	lm92_init_client(new_client);

	/* Register sysfs hooks */
	err = sysfs_create_group(&new_client->dev.kobj, &lm92_group);
	if (err)
		return err;

	data->hwmon_dev = hwmon_device_register(&new_client->dev);
	if (IS_ERR(data->hwmon_dev)) {
		err = PTR_ERR(data->hwmon_dev);
		goto exit_remove;
	}

	return 0;

exit_remove:
	sysfs_remove_group(&new_client->dev.kobj, &lm92_group);
	return err;
}

static int lm92_remove(struct i2c_client *client)
{
	struct lm92_data *data = i2c_get_clientdata(client);

	hwmon_device_unregister(data->hwmon_dev);
	sysfs_remove_group(&client->dev.kobj, &lm92_group);

	return 0;
}


/*
 * Module and driver stuff
 */

static const struct i2c_device_id lm92_id[] = {
	{ "lm92", 0 },
	/* max6635 could be added here */
	{ }
};
MODULE_DEVICE_TABLE(i2c, lm92_id);

static struct i2c_driver lm92_driver = {
	.class		= I2C_CLASS_HWMON,
	.driver = {
		.name	= "lm92",
	},
	.probe		= lm92_probe,
	.remove		= lm92_remove,
	.id_table	= lm92_id,
	.detect		= lm92_detect,
	.address_list	= normal_i2c,
};

module_i2c_driver(lm92_driver);

MODULE_AUTHOR("Jean Delvare <khali@linux-fr.org>");
MODULE_DESCRIPTION("LM92/MAX6635 driver");
MODULE_LICENSE("GPL");
Commit	Line	Data
1da177e4 LT	1	/*
1da177e4 LT	2	* lm92 - Hardware monitoring driver
910e8dcf	3	* Copyright (C) 2005-2008 Jean Delvare <khali@linux-fr.org>
1da177e4 LT	4	*
	5	* Based on the lm90 driver, with some ideas taken from the lm_sensors
	6	* lm92 driver as well.
	7	*
	8	* The LM92 is a sensor chip made by National Semiconductor. It reports
	9	* its own temperature with a 0.0625 deg resolution and a 0.33 deg
	10	* accuracy. Complete datasheet can be obtained from National's website
	11	* at:
	12	* http://www.national.com/pf/LM/LM92.html
	13	*
	14	* This driver also supports the MAX6635 sensor chip made by Maxim.
	15	* This chip is compatible with the LM92, but has a lesser accuracy
	16	* (1.0 deg). Complete datasheet can be obtained from Maxim's website
	17	* at:
	18	* http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3074
	19	*
	20	* Since the LM92 was the first chipset supported by this driver, most
	21	* comments will refer to this chipset, but are actually general and
	22	* concern all supported chipsets, unless mentioned otherwise.
	23	*
	24	* Support could easily be added for the National Semiconductor LM76
	25	* and Maxim MAX6633 and MAX6634 chips, which are mostly compatible
	26	* with the LM92.
	27	*
	28	* This program is free software; you can redistribute it and/or modify
	29	* it under the terms of the GNU General Public License as published by
	30	* the Free Software Foundation; either version 2 of the License, or
	31	* (at your option) any later version.
	32	*
	33	* This program is distributed in the hope that it will be useful,
	34	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	35	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	36	* GNU General Public License for more details.
	37	*
	38	* You should have received a copy of the GNU General Public License
	39	* along with this program; if not, write to the Free Software
	40	* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
	41	*/
	42
	43	#include <linux/module.h>
	44	#include <linux/init.h>
	45	#include <linux/slab.h>
	46	#include <linux/i2c.h>
943b0830	47	#include <linux/hwmon.h>
6cb59e91	48	#include <linux/hwmon-sysfs.h>
943b0830	49	#include <linux/err.h>
9a61bf63	50	#include <linux/mutex.h>
1da177e4	51
a318afd8 GR	52	/*
	53	* The LM92 and MAX6635 have 2 two-state pins for address selection,
	54	* resulting in 4 possible addresses.
	55	*/
25e9c86d MH	56	static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b,
25e9c86d MH	57	I2C_CLIENT_END };
1da177e4	58
1da177e4 LT	59	/* The LM92 registers */
	60	#define LM92_REG_CONFIG 0x01 /* 8-bit, RW */
	61	#define LM92_REG_TEMP 0x00 /* 16-bit, RO */
	62	#define LM92_REG_TEMP_HYST 0x02 /* 16-bit, RW */
	63	#define LM92_REG_TEMP_CRIT 0x03 /* 16-bit, RW */
	64	#define LM92_REG_TEMP_LOW 0x04 /* 16-bit, RW */
	65	#define LM92_REG_TEMP_HIGH 0x05 /* 16-bit, RW */
	66	#define LM92_REG_MAN_ID 0x07 /* 16-bit, RO, LM92 only */
	67
a318afd8 GR	68	/*
	69	* The LM92 uses signed 13-bit values with LSB = 0.0625 degree Celsius,
	70	* left-justified in 16-bit registers. No rounding is done, with such
	71	* a resolution it's just not worth it. Note that the MAX6635 doesn't
	72	* make use of the 4 lower bits for limits (i.e. effective resolution
	73	* for limits is 1 degree Celsius).
	74	*/
1da177e4 LT	75	static inline int TEMP_FROM_REG(s16 reg)
	76	{
	77	return reg / 8 * 625 / 10;
	78	}
	79
	80	static inline s16 TEMP_TO_REG(int val)
	81	{
	82	if (val <= -60000)
	83	return -60000 * 10 / 625 * 8;
	84	if (val >= 160000)
	85	return 160000 * 10 / 625 * 8;
	86	return val * 10 / 625 * 8;
	87	}
	88
	89	/* Alarm flags are stored in the 3 LSB of the temperature register */
	90	static inline u8 ALARMS_FROM_REG(s16 reg)
	91	{
	92	return reg & 0x0007;
	93	}
	94
	95	/* Driver data (common to all clients) */
	96	static struct i2c_driver lm92_driver;
	97
	98	/* Client data (each client gets its own) */
	99	struct lm92_data {
1beeffe4	100	struct device *hwmon_dev;
9a61bf63	101	struct mutex update_lock;
1da177e4 LT	102	char valid; /* zero until following fields are valid */
	103	unsigned long last_updated; /* in jiffies */
	104
	105	/* registers values */
	106	s16 temp1_input, temp1_crit, temp1_min, temp1_max, temp1_hyst;
	107	};
	108
	109
	110	/*
	111	* Sysfs attributes and callback functions
	112	*/
	113
	114	static struct lm92_data lm92_update_device(struct device dev)
	115	{
	116	struct i2c_client *client = to_i2c_client(dev);
	117	struct lm92_data *data = i2c_get_clientdata(client);
	118
9a61bf63	119	mutex_lock(&data->update_lock);
1da177e4 LT	120
	121	if (time_after(jiffies, data->last_updated + HZ)
	122	\|\| !data->valid) {
	123	dev_dbg(&client->dev, "Updating lm92 data\n");
90f4102c JD	124	data->temp1_input = i2c_smbus_read_word_swapped(client,
	125	LM92_REG_TEMP);
	126	data->temp1_hyst = i2c_smbus_read_word_swapped(client,
	127	LM92_REG_TEMP_HYST);
	128	data->temp1_crit = i2c_smbus_read_word_swapped(client,
	129	LM92_REG_TEMP_CRIT);
	130	data->temp1_min = i2c_smbus_read_word_swapped(client,
	131	LM92_REG_TEMP_LOW);
	132	data->temp1_max = i2c_smbus_read_word_swapped(client,
	133	LM92_REG_TEMP_HIGH);
1da177e4 LT	134
	135	data->last_updated = jiffies;
	136	data->valid = 1;
	137	}
	138
9a61bf63	139	mutex_unlock(&data->update_lock);
1da177e4 LT	140
	141	return data;
	142	}
	143
	144	#define show_temp(value) \
a318afd8 GR	145	static ssize_t show_##value(struct device dev, struct device_attribute attr, \
a318afd8 GR	146	char *buf) \
1da177e4 LT	147	{ \
	148	struct lm92_data *data = lm92_update_device(dev); \
	149	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->value)); \
	150	}
	151	show_temp(temp1_input);
	152	show_temp(temp1_crit);
	153	show_temp(temp1_min);
	154	show_temp(temp1_max);
	155
	156	#define set_temp(value, reg) \
a318afd8 GR	157	static ssize_t set_##value(struct device dev, struct device_attribute attr, \
a318afd8 GR	158	const char *buf, \
1da177e4 LT	159	size_t count) \
	160	{ \
	161	struct i2c_client *client = to_i2c_client(dev); \
	162	struct lm92_data *data = i2c_get_clientdata(client); \
a318afd8 GR	163	long val; \
	164	int err = kstrtol(buf, 10, &val); \
	165	if (err) \
	166	return err; \
	167	\
9a61bf63	168	mutex_lock(&data->update_lock); \
1da177e4	169	data->value = TEMP_TO_REG(val); \
90f4102c	170	i2c_smbus_write_word_swapped(client, reg, data->value); \
9a61bf63	171	mutex_unlock(&data->update_lock); \
1da177e4 LT	172	return count; \
	173	}
	174	set_temp(temp1_crit, LM92_REG_TEMP_CRIT);
	175	set_temp(temp1_min, LM92_REG_TEMP_LOW);
	176	set_temp(temp1_max, LM92_REG_TEMP_HIGH);
	177
a318afd8 GR	178	static ssize_t show_temp1_crit_hyst(struct device *dev,
a318afd8 GR	179	struct device_attribute attr, char buf)
1da177e4 LT	180	{
	181	struct lm92_data *data = lm92_update_device(dev);
	182	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp1_crit)
	183	- TEMP_FROM_REG(data->temp1_hyst));
	184	}
a318afd8 GR	185	static ssize_t show_temp1_max_hyst(struct device *dev,
a318afd8 GR	186	struct device_attribute attr, char buf)
1da177e4 LT	187	{
	188	struct lm92_data *data = lm92_update_device(dev);
	189	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp1_max)
	190	- TEMP_FROM_REG(data->temp1_hyst));
	191	}
a318afd8 GR	192	static ssize_t show_temp1_min_hyst(struct device *dev,
a318afd8 GR	193	struct device_attribute attr, char buf)
1da177e4 LT	194	{
	195	struct lm92_data *data = lm92_update_device(dev);
	196	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp1_min)
	197	+ TEMP_FROM_REG(data->temp1_hyst));
	198	}
	199
a318afd8 GR	200	static ssize_t set_temp1_crit_hyst(struct device *dev,
	201	struct device_attribute *attr,
	202	const char *buf, size_t count)
1da177e4 LT	203	{
	204	struct i2c_client *client = to_i2c_client(dev);
	205	struct lm92_data *data = i2c_get_clientdata(client);
a318afd8 GR	206	long val;
	207	int err;
	208
	209	err = kstrtol(buf, 10, &val);
	210	if (err)
	211	return err;
1da177e4	212
9a61bf63	213	mutex_lock(&data->update_lock);
1da177e4	214	data->temp1_hyst = TEMP_FROM_REG(data->temp1_crit) - val;
90f4102c JD	215	i2c_smbus_write_word_swapped(client, LM92_REG_TEMP_HYST,
90f4102c JD	216	TEMP_TO_REG(data->temp1_hyst));
9a61bf63	217	mutex_unlock(&data->update_lock);
1da177e4 LT	218	return count;
	219	}
	220
a318afd8 GR	221	static ssize_t show_alarms(struct device dev, struct device_attribute attr,
a318afd8 GR	222	char *buf)
1da177e4 LT	223	{
	224	struct lm92_data *data = lm92_update_device(dev);
	225	return sprintf(buf, "%d\n", ALARMS_FROM_REG(data->temp1_input));
	226	}
	227
6cb59e91 JD	228	static ssize_t show_alarm(struct device dev, struct device_attribute attr,
	229	char *buf)
	230	{
	231	int bitnr = to_sensor_dev_attr(attr)->index;
	232	struct lm92_data *data = lm92_update_device(dev);
	233	return sprintf(buf, "%d\n", (data->temp1_input >> bitnr) & 1);
	234	}
	235
1da177e4 LT	236	static DEVICE_ATTR(temp1_input, S_IRUGO, show_temp1_input, NULL);
	237	static DEVICE_ATTR(temp1_crit, S_IWUSR \| S_IRUGO, show_temp1_crit,
	238	set_temp1_crit);
	239	static DEVICE_ATTR(temp1_crit_hyst, S_IWUSR \| S_IRUGO, show_temp1_crit_hyst,
	240	set_temp1_crit_hyst);
	241	static DEVICE_ATTR(temp1_min, S_IWUSR \| S_IRUGO, show_temp1_min,
	242	set_temp1_min);
	243	static DEVICE_ATTR(temp1_min_hyst, S_IRUGO, show_temp1_min_hyst, NULL);
	244	static DEVICE_ATTR(temp1_max, S_IWUSR \| S_IRUGO, show_temp1_max,
	245	set_temp1_max);
	246	static DEVICE_ATTR(temp1_max_hyst, S_IRUGO, show_temp1_max_hyst, NULL);
	247	static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
6cb59e91 JD	248	static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 2);
	249	static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL, 0);
	250	static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 1);
1da177e4 LT	251
	252
	253	/*
	254	* Detection and registration
	255	*/
	256
	257	static void lm92_init_client(struct i2c_client *client)
	258	{
	259	u8 config;
	260
	261	/* Start the conversions if needed */
	262	config = i2c_smbus_read_byte_data(client, LM92_REG_CONFIG);
	263	if (config & 0x01)
	264	i2c_smbus_write_byte_data(client, LM92_REG_CONFIG,
	265	config & 0xFE);
	266	}
	267
a318afd8 GR	268	/*
	269	* The MAX6635 has no identification register, so we have to use tricks
	270	* to identify it reliably. This is somewhat slow.
	271	* Note that we do NOT rely on the 2 MSB of the configuration register
	272	* always reading 0, as suggested by the datasheet, because it was once
	273	* reported not to be true.
	274	*/
1da177e4 LT	275	static int max6635_check(struct i2c_client *client)
	276	{
	277	u16 temp_low, temp_high, temp_hyst, temp_crit;
	278	u8 conf;
	279	int i;
	280
a318afd8 GR	281	/*
	282	* No manufacturer ID register, so a read from this address will
	283	* always return the last read value.
	284	*/
1da177e4 LT	285	temp_low = i2c_smbus_read_word_data(client, LM92_REG_TEMP_LOW);
	286	if (i2c_smbus_read_word_data(client, LM92_REG_MAN_ID) != temp_low)
	287	return 0;
	288	temp_high = i2c_smbus_read_word_data(client, LM92_REG_TEMP_HIGH);
	289	if (i2c_smbus_read_word_data(client, LM92_REG_MAN_ID) != temp_high)
	290	return 0;
a318afd8	291
1da177e4 LT	292	/* Limits are stored as integer values (signed, 9-bit). */
	293	if ((temp_low & 0x7f00) \|\| (temp_high & 0x7f00))
	294	return 0;
	295	temp_hyst = i2c_smbus_read_word_data(client, LM92_REG_TEMP_HYST);
	296	temp_crit = i2c_smbus_read_word_data(client, LM92_REG_TEMP_CRIT);
	297	if ((temp_hyst & 0x7f00) \|\| (temp_crit & 0x7f00))
	298	return 0;
	299
a318afd8 GR	300	/*
	301	* Registers addresses were found to cycle over 16-byte boundaries.
	302	* We don't test all registers with all offsets so as to save some
	303	* reads and time, but this should still be sufficient to dismiss
	304	* non-MAX6635 chips.
	305	*/
1da177e4	306	conf = i2c_smbus_read_byte_data(client, LM92_REG_CONFIG);
a318afd8	307	for (i = 16; i < 96; i *= 2) {
1da177e4	308	if (temp_hyst != i2c_smbus_read_word_data(client,
a318afd8	309	LM92_REG_TEMP_HYST + i - 16)
1da177e4	310	\|\| temp_crit != i2c_smbus_read_word_data(client,
a318afd8	311	LM92_REG_TEMP_CRIT + i)
1da177e4 LT	312	\|\| temp_low != i2c_smbus_read_word_data(client,
	313	LM92_REG_TEMP_LOW + i + 16)
	314	\|\| temp_high != i2c_smbus_read_word_data(client,
a318afd8	315	LM92_REG_TEMP_HIGH + i + 32)
1da177e4	316	\|\| conf != i2c_smbus_read_byte_data(client,
a318afd8	317	LM92_REG_CONFIG + i))
1da177e4 LT	318	return 0;
	319	}
	320
	321	return 1;
	322	}
	323
0501a381 MH	324	static struct attribute *lm92_attributes[] = {
	325	&dev_attr_temp1_input.attr,
	326	&dev_attr_temp1_crit.attr,
	327	&dev_attr_temp1_crit_hyst.attr,
	328	&dev_attr_temp1_min.attr,
	329	&dev_attr_temp1_min_hyst.attr,
	330	&dev_attr_temp1_max.attr,
	331	&dev_attr_temp1_max_hyst.attr,
	332	&dev_attr_alarms.attr,
6cb59e91 JD	333	&sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
	334	&sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
	335	&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
0501a381 MH	336	NULL
	337	};
	338
	339	static const struct attribute_group lm92_group = {
	340	.attrs = lm92_attributes,
	341	};
	342
910e8dcf	343	/* Return 0 if detection is successful, -ENODEV otherwise */
310ec792	344	static int lm92_detect(struct i2c_client *new_client,
910e8dcf	345	struct i2c_board_info *info)
1da177e4	346	{
910e8dcf	347	struct i2c_adapter *adapter = new_client->adapter;
52df6440 JD	348	u8 config;
52df6440 JD	349	u16 man_id;
1da177e4 LT	350
	351	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA
	352	\| I2C_FUNC_SMBUS_WORD_DATA))
910e8dcf	353	return -ENODEV;
1da177e4	354
52df6440 JD	355	config = i2c_smbus_read_byte_data(new_client, LM92_REG_CONFIG);
	356	man_id = i2c_smbus_read_word_data(new_client, LM92_REG_MAN_ID);
	357
	358	if ((config & 0xe0) == 0x00 && man_id == 0x0180)
	359	pr_info("lm92: Found National Semiconductor LM92 chip\n");
	360	else if (max6635_check(new_client))
	361	pr_info("lm92: Found Maxim MAX6635 chip\n");
	362	else
	363	return -ENODEV;
1da177e4	364
910e8dcf JD	365	strlcpy(info->type, "lm92", I2C_NAME_SIZE);
	366
	367	return 0;
	368	}
	369
	370	static int lm92_probe(struct i2c_client *new_client,
	371	const struct i2c_device_id *id)
	372	{
	373	struct lm92_data *data;
	374	int err;
	375
705375cc GR	376	data = devm_kzalloc(&new_client->dev, sizeof(struct lm92_data),
	377	GFP_KERNEL);
	378	if (!data)
	379	return -ENOMEM;
910e8dcf JD	380
910e8dcf JD	381	i2c_set_clientdata(new_client, data);
1da177e4	382	data->valid = 0;
9a61bf63	383	mutex_init(&data->update_lock);
1da177e4	384
1da177e4 LT	385	/* Initialize the chipset */
	386	lm92_init_client(new_client);
	387
	388	/* Register sysfs hooks */
a318afd8 GR	389	err = sysfs_create_group(&new_client->dev.kobj, &lm92_group);
a318afd8 GR	390	if (err)
705375cc	391	return err;
0501a381	392
1beeffe4 TJ	393	data->hwmon_dev = hwmon_device_register(&new_client->dev);
	394	if (IS_ERR(data->hwmon_dev)) {
	395	err = PTR_ERR(data->hwmon_dev);
0501a381	396	goto exit_remove;
943b0830 MH	397	}
943b0830 MH	398
1da177e4 LT	399	return 0;
1da177e4 LT	400
0501a381 MH	401	exit_remove:
0501a381 MH	402	sysfs_remove_group(&new_client->dev.kobj, &lm92_group);
1da177e4 LT	403	return err;
	404	}
	405
910e8dcf	406	static int lm92_remove(struct i2c_client *client)
1da177e4	407	{
943b0830	408	struct lm92_data *data = i2c_get_clientdata(client);
1da177e4	409
1beeffe4	410	hwmon_device_unregister(data->hwmon_dev);
0501a381	411	sysfs_remove_group(&client->dev.kobj, &lm92_group);
943b0830	412
1da177e4 LT	413	return 0;
	414	}
	415
	416
	417	/*
	418	* Module and driver stuff
	419	*/
	420
910e8dcf	421	static const struct i2c_device_id lm92_id[] = {
1f86df49	422	{ "lm92", 0 },
910e8dcf JD	423	/* max6635 could be added here */
	424	{ }
	425	};
	426	MODULE_DEVICE_TABLE(i2c, lm92_id);
	427
1da177e4	428	static struct i2c_driver lm92_driver = {
910e8dcf	429	.class = I2C_CLASS_HWMON,
cdaf7934	430	.driver = {
cdaf7934 LR	431	.name = "lm92",
cdaf7934 LR	432	},
910e8dcf JD	433	.probe = lm92_probe,
	434	.remove = lm92_remove,
	435	.id_table = lm92_id,
	436	.detect = lm92_detect,
c3813d6a	437	.address_list = normal_i2c,
1da177e4 LT	438	};
1da177e4 LT	439
f0967eea	440	module_i2c_driver(lm92_driver);
1da177e4 LT	441
	442	MODULE_AUTHOR("Jean Delvare <khali@linux-fr.org>");
	443	MODULE_DESCRIPTION("LM92/MAX6635 driver");
	444	MODULE_LICENSE("GPL");