[deliverable/linux.git] / drivers / ide / pci / serverworks.c

/*
 * Copyright (C) 1998-2000 Michel Aubry
 * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
 * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
 * Copyright (C)      2007 Bartlomiej Zolnierkiewicz
 * Portions copyright (c) 2001 Sun Microsystems
 *
 *
 * RCC/ServerWorks IDE driver for Linux
 *
 *   OSB4: `Open South Bridge' IDE Interface (fn 1)
 *         supports UDMA mode 2 (33 MB/s)
 *
 *   CSB5: `Champion South Bridge' IDE Interface (fn 1)
 *         all revisions support UDMA mode 4 (66 MB/s)
 *         revision A2.0 and up support UDMA mode 5 (100 MB/s)
 *
 *         *** The CSB5 does not provide ANY register ***
 *         *** to detect 80-conductor cable presence. ***
 *
 *   CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
 *
 *   HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
 *   controller same as the CSB6. Single channel ATA100 only.
 *
 * Documentation:
 *	Available under NDA only. Errata info very hard to get.
 *
 */

#include <linux/types.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>

#include <asm/io.h>

#define DRV_NAME "serverworks"

#define SVWKS_CSB5_REVISION_NEW	0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
#define SVWKS_CSB6_REVISION	0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */

/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
 * can overrun their FIFOs when used with the CSB5 */
static const char *svwks_bad_ata100[] = {
	"ST320011A",
	"ST340016A",
	"ST360021A",
	"ST380021A",
	NULL
};

static struct pci_dev *isa_dev;

static int check_in_drive_lists (ide_drive_t *drive, const char **list)
{
	char *m = (char *)&drive->id[ATA_ID_PROD];

	while (*list)
		if (!strcmp(*list++, m))
			return 1;
	return 0;
}

static u8 svwks_udma_filter(ide_drive_t *drive)
{
	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
	u8 mask = 0;

	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
		return 0x1f;
	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
		u32 reg = 0;
		if (isa_dev)
			pci_read_config_dword(isa_dev, 0x64, &reg);
			
		/*
		 *	Don't enable UDMA on disk devices for the moment
		 */
		if(drive->media == ide_disk)
			return 0;
		/* Check the OSB4 DMA33 enable bit */
		return ((reg & 0x00004000) == 0x00004000) ? 0x07 : 0;
	} else if (dev->revision < SVWKS_CSB5_REVISION_NEW) {
		return 0x07;
	} else if (dev->revision >= SVWKS_CSB5_REVISION_NEW) {
		u8 btr = 0, mode;
		pci_read_config_byte(dev, 0x5A, &btr);
		mode = btr & 0x3;

		/* If someone decides to do UDMA133 on CSB5 the same
		   issue will bite so be inclusive */
		if (mode > 2 && check_in_drive_lists(drive, svwks_bad_ata100))
			mode = 2;

		switch(mode) {
		case 3:	 mask = 0x3f; break;
		case 2:	 mask = 0x1f; break;
		case 1:	 mask = 0x07; break;
		default: mask = 0x00; break;
		}
	}
	if (((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
	     (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) &&
	    (!(PCI_FUNC(dev->devfn) & 1)))
		mask = 0x1f;

	return mask;
}

static u8 svwks_csb_check (struct pci_dev *dev)
{
	switch (dev->device) {
		case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
		case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
		case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
		case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
			return 1;
		default:
			break;
	}
	return 0;
}

static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
	static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
	static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };

	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);

	pci_write_config_byte(dev, drive_pci[drive->dn], pio_modes[pio]);

	if (svwks_csb_check(dev)) {
		u16 csb_pio = 0;

		pci_read_config_word(dev, 0x4a, &csb_pio);

		csb_pio &= ~(0x0f << (4 * drive->dn));
		csb_pio |= (pio << (4 * drive->dn));

		pci_write_config_word(dev, 0x4a, csb_pio);
	}
}

static void svwks_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
	static const u8 udma_modes[]		= { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
	static const u8 dma_modes[]		= { 0x77, 0x21, 0x20 };
	static const u8 drive_pci2[]		= { 0x45, 0x44, 0x47, 0x46 };

	ide_hwif_t *hwif	= HWIF(drive);
	struct pci_dev *dev	= to_pci_dev(hwif->dev);
	u8 unit			= (drive->select.b.unit & 0x01);

	u8 ultra_enable	 = 0, ultra_timing = 0, dma_timing = 0;

	pci_read_config_byte(dev, (0x56|hwif->channel), &ultra_timing);
	pci_read_config_byte(dev, 0x54, &ultra_enable);

	ultra_timing	&= ~(0x0F << (4*unit));
	ultra_enable	&= ~(0x01 << drive->dn);

	if (speed >= XFER_UDMA_0) {
		dma_timing   |= dma_modes[2];
		ultra_timing |= (udma_modes[speed - XFER_UDMA_0] << (4 * unit));
		ultra_enable |= (0x01 << drive->dn);
	} else if (speed >= XFER_MW_DMA_0)
		dma_timing   |= dma_modes[speed - XFER_MW_DMA_0];

	pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
	pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
	pci_write_config_byte(dev, 0x54, ultra_enable);
}

static unsigned int __devinit init_chipset_svwks(struct pci_dev *dev)
{
	unsigned int reg;
	u8 btr;

	/* force Master Latency Timer value to 64 PCICLKs */
	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x40);

	/* OSB4 : South Bridge and IDE */
	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
		isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
			  PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
		if (isa_dev) {
			pci_read_config_dword(isa_dev, 0x64, &reg);
			reg &= ~0x00002000; /* disable 600ns interrupt mask */
			if(!(reg & 0x00004000))
				printk(KERN_DEBUG DRV_NAME " %s: UDMA not BIOS "
					"enabled.\n", pci_name(dev));
			reg |=  0x00004000; /* enable UDMA/33 support */
			pci_write_config_dword(isa_dev, 0x64, reg);
		}
	}

	/* setup CSB5/CSB6 : South Bridge and IDE option RAID */
	else if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
		 (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
		 (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {

		/* Third Channel Test */
		if (!(PCI_FUNC(dev->devfn) & 1)) {
			struct pci_dev * findev = NULL;
			u32 reg4c = 0;
			findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
				PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
			if (findev) {
				pci_read_config_dword(findev, 0x4C, &reg4c);
				reg4c &= ~0x000007FF;
				reg4c |=  0x00000040;
				reg4c |=  0x00000020;
				pci_write_config_dword(findev, 0x4C, reg4c);
				pci_dev_put(findev);
			}
			outb_p(0x06, 0x0c00);
			dev->irq = inb_p(0x0c01);
		} else {
			struct pci_dev * findev = NULL;
			u8 reg41 = 0;

			findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
					PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
			if (findev) {
				pci_read_config_byte(findev, 0x41, &reg41);
				reg41 &= ~0x40;
				pci_write_config_byte(findev, 0x41, reg41);
				pci_dev_put(findev);
			}
			/*
			 * This is a device pin issue on CSB6.
			 * Since there will be a future raid mode,
			 * early versions of the chipset require the
			 * interrupt pin to be set, and it is a compatibility
			 * mode issue.
			 */
			if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
				dev->irq = 0;
		}
//		pci_read_config_dword(dev, 0x40, &pioreg)
//		pci_write_config_dword(dev, 0x40, 0x99999999);
//		pci_read_config_dword(dev, 0x44, &dmareg);
//		pci_write_config_dword(dev, 0x44, 0xFFFFFFFF);
		/* setup the UDMA Control register
		 *
		 * 1. clear bit 6 to enable DMA
		 * 2. enable DMA modes with bits 0-1
		 * 	00 : legacy
		 * 	01 : udma2
		 * 	10 : udma2/udma4
		 * 	11 : udma2/udma4/udma5
		 */
		pci_read_config_byte(dev, 0x5A, &btr);
		btr &= ~0x40;
		if (!(PCI_FUNC(dev->devfn) & 1))
			btr |= 0x2;
		else
			btr |= (dev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
		pci_write_config_byte(dev, 0x5A, btr);
	}
	/* Setup HT1000 SouthBridge Controller - Single Channel Only */
	else if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
		pci_read_config_byte(dev, 0x5A, &btr);
		btr &= ~0x40;
		btr |= 0x3;
		pci_write_config_byte(dev, 0x5A, btr);
	}

	return dev->irq;
}

static u8 ata66_svwks_svwks(ide_hwif_t *hwif)
{
	return ATA_CBL_PATA80;
}

/* On Dell PowerEdge servers with a CSB5/CSB6, the top two bits
 * of the subsystem device ID indicate presence of an 80-pin cable.
 * Bit 15 clear = secondary IDE channel does not have 80-pin cable.
 * Bit 15 set   = secondary IDE channel has 80-pin cable.
 * Bit 14 clear = primary IDE channel does not have 80-pin cable.
 * Bit 14 set   = primary IDE channel has 80-pin cable.
 */
static u8 ata66_svwks_dell(ide_hwif_t *hwif)
{
	struct pci_dev *dev = to_pci_dev(hwif->dev);

	if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
	    dev->vendor	== PCI_VENDOR_ID_SERVERWORKS &&
	    (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE ||
	     dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE))
		return ((1 << (hwif->channel + 14)) &
			dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
	return ATA_CBL_PATA40;
}

/* Sun Cobalt Alpine hardware avoids the 80-pin cable
 * detect issue by attaching the drives directly to the board.
 * This check follows the Dell precedent (how scary is that?!)
 *
 * WARNING: this only works on Alpine hardware!
 */
static u8 ata66_svwks_cobalt(ide_hwif_t *hwif)
{
	struct pci_dev *dev = to_pci_dev(hwif->dev);

	if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
	    dev->vendor	== PCI_VENDOR_ID_SERVERWORKS &&
	    dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
		return ((1 << (hwif->channel + 14)) &
			dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
	return ATA_CBL_PATA40;
}

static u8 svwks_cable_detect(ide_hwif_t *hwif)
{
	struct pci_dev *dev = to_pci_dev(hwif->dev);

	/* Server Works */
	if (dev->subsystem_vendor == PCI_VENDOR_ID_SERVERWORKS)
		return ata66_svwks_svwks (hwif);
	
	/* Dell PowerEdge */
	if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL)
		return ata66_svwks_dell (hwif);

	/* Cobalt Alpine */
	if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN)
		return ata66_svwks_cobalt (hwif);

	/* Per Specified Design by OEM, and ASIC Architect */
	if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
	    (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2))
		return ATA_CBL_PATA80;

	return ATA_CBL_PATA40;
}

static const struct ide_port_ops osb4_port_ops = {
	.set_pio_mode		= svwks_set_pio_mode,
	.set_dma_mode		= svwks_set_dma_mode,
	.udma_filter		= svwks_udma_filter,
};

static const struct ide_port_ops svwks_port_ops = {
	.set_pio_mode		= svwks_set_pio_mode,
	.set_dma_mode		= svwks_set_dma_mode,
	.udma_filter		= svwks_udma_filter,
	.cable_detect		= svwks_cable_detect,
};

#define IDE_HFLAGS_SVWKS IDE_HFLAG_LEGACY_IRQS

static const struct ide_port_info serverworks_chipsets[] __devinitdata = {
	{	/* 0: OSB4 */
		.name		= DRV_NAME,
		.init_chipset	= init_chipset_svwks,
		.port_ops	= &osb4_port_ops,
		.host_flags	= IDE_HFLAGS_SVWKS,
		.pio_mask	= ATA_PIO4,
		.mwdma_mask	= ATA_MWDMA2,
		.udma_mask	= 0x00, /* UDMA is problematic on OSB4 */
	},
	{	/* 1: CSB5 */
		.name		= DRV_NAME,
		.init_chipset	= init_chipset_svwks,
		.port_ops	= &svwks_port_ops,
		.host_flags	= IDE_HFLAGS_SVWKS,
		.pio_mask	= ATA_PIO4,
		.mwdma_mask	= ATA_MWDMA2,
		.udma_mask	= ATA_UDMA5,
	},
	{	/* 2: CSB6 */
		.name		= DRV_NAME,
		.init_chipset	= init_chipset_svwks,
		.port_ops	= &svwks_port_ops,
		.host_flags	= IDE_HFLAGS_SVWKS,
		.pio_mask	= ATA_PIO4,
		.mwdma_mask	= ATA_MWDMA2,
		.udma_mask	= ATA_UDMA5,
	},
	{	/* 3: CSB6-2 */
		.name		= DRV_NAME,
		.init_chipset	= init_chipset_svwks,
		.port_ops	= &svwks_port_ops,
		.host_flags	= IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
		.pio_mask	= ATA_PIO4,
		.mwdma_mask	= ATA_MWDMA2,
		.udma_mask	= ATA_UDMA5,
	},
	{	/* 4: HT1000 */
		.name		= DRV_NAME,
		.init_chipset	= init_chipset_svwks,
		.port_ops	= &svwks_port_ops,
		.host_flags	= IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
		.pio_mask	= ATA_PIO4,
		.mwdma_mask	= ATA_MWDMA2,
		.udma_mask	= ATA_UDMA5,
	}
};

/**
 *	svwks_init_one	-	called when a OSB/CSB is found
 *	@dev: the svwks device
 *	@id: the matching pci id
 *
 *	Called when the PCI registration layer (or the IDE initialization)
 *	finds a device matching our IDE device tables.
 */
 
static int __devinit svwks_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
	struct ide_port_info d;
	u8 idx = id->driver_data;

	d = serverworks_chipsets[idx];

	if (idx == 1)
		d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
	else if (idx == 2 || idx == 3) {
		if ((PCI_FUNC(dev->devfn) & 1) == 0) {
			if (pci_resource_start(dev, 0) != 0x01f1)
				d.host_flags |= IDE_HFLAG_NON_BOOTABLE;
			d.host_flags |= IDE_HFLAG_SINGLE;
		} else
			d.host_flags &= ~IDE_HFLAG_SINGLE;
	}

	return ide_pci_init_one(dev, &d, NULL);
}

static const struct pci_device_id svwks_pci_tbl[] = {
	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE),   0 },
	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE),   1 },
	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE),   2 },
	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2),  3 },
	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 4 },
	{ 0, },
};
MODULE_DEVICE_TABLE(pci, svwks_pci_tbl);

static struct pci_driver driver = {
	.name		= "Serverworks_IDE",
	.id_table	= svwks_pci_tbl,
	.probe		= svwks_init_one,
	.remove		= ide_pci_remove,
};

static int __init svwks_ide_init(void)
{
	return ide_pci_register_driver(&driver);
}

static void __exit svwks_ide_exit(void)
{
	pci_unregister_driver(&driver);
}

module_init(svwks_ide_init);
module_exit(svwks_ide_exit);

MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick");
MODULE_DESCRIPTION("PCI driver module for Serverworks OSB4/CSB5/CSB6 IDE");
MODULE_LICENSE("GPL");
Commit	Line	Data
1da177e4	1	/*
1da177e4 LT	2	* Copyright (C) 1998-2000 Michel Aubry
	3	* Copyright (C) 1998-2000 Andrzej Krzysztofowicz
	4	* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
9445de76	5	* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
1da177e4 LT	6	* Portions copyright (c) 2001 Sun Microsystems
	7	*
	8	*
	9	* RCC/ServerWorks IDE driver for Linux
	10	*
	11	* OSB4: `Open South Bridge' IDE Interface (fn 1)
	12	* supports UDMA mode 2 (33 MB/s)
	13	*
	14	* CSB5: `Champion South Bridge' IDE Interface (fn 1)
	15	* all revisions support UDMA mode 4 (66 MB/s)
	16	* revision A2.0 and up support UDMA mode 5 (100 MB/s)
	17	*
	18	* * The CSB5 does not provide ANY register *
	19	* * to detect 80-conductor cable presence. *
	20	*
	21	* CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
	22	*
84f57fbc NS	23	* HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
	24	* controller same as the CSB6. Single channel ATA100 only.
	25	*
1da177e4 LT	26	* Documentation:
	27	* Available under NDA only. Errata info very hard to get.
	28	*
	29	*/
	30
1da177e4 LT	31	#include <linux/types.h>
	32	#include <linux/module.h>
	33	#include <linux/kernel.h>
1da177e4 LT	34	#include <linux/pci.h>
	35	#include <linux/hdreg.h>
	36	#include <linux/ide.h>
	37	#include <linux/init.h>
1da177e4 LT	38
	39	#include <asm/io.h>
	40
ced3ec8a BZ	41	#define DRV_NAME "serverworks"
ced3ec8a BZ	42
1da177e4 LT	43	#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
	44	#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
	45
	46	/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
	47	* can overrun their FIFOs when used with the CSB5 */
	48	static const char *svwks_bad_ata100[] = {
	49	"ST320011A",
	50	"ST340016A",
	51	"ST360021A",
	52	"ST380021A",
	53	NULL
	54	};
	55
1da177e4 LT	56	static struct pci_dev *isa_dev;
	57
	58	static int check_in_drive_lists (ide_drive_t drive, const char *list)
	59	{
4dde4492 BZ	60	char m = (char )&drive->id[ATA_ID_PROD];
4dde4492 BZ	61
1da177e4	62	while (*list)
4dde4492	63	if (!strcmp(*list++, m))
1da177e4 LT	64	return 1;
	65	return 0;
	66	}
	67
2d5eaa6d	68	static u8 svwks_udma_filter(ide_drive_t *drive)
1da177e4	69	{
36501650	70	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
2d5eaa6d	71	u8 mask = 0;
1da177e4	72
84f57fbc	73	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
2d5eaa6d	74	return 0x1f;
1da177e4 LT	75	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
	76	u32 reg = 0;
	77	if (isa_dev)
	78	pci_read_config_dword(isa_dev, 0x64, &reg);
	79
	80	/*
	81	* Don't enable UDMA on disk devices for the moment
	82	*/
	83	if(drive->media == ide_disk)
	84	return 0;
	85	/* Check the OSB4 DMA33 enable bit */
2d5eaa6d	86	return ((reg & 0x00004000) == 0x00004000) ? 0x07 : 0;
44c10138	87	} else if (dev->revision < SVWKS_CSB5_REVISION_NEW) {
2d5eaa6d	88	return 0x07;
44c10138	89	} else if (dev->revision >= SVWKS_CSB5_REVISION_NEW) {
2d5eaa6d	90	u8 btr = 0, mode;
1da177e4 LT	91	pci_read_config_byte(dev, 0x5A, &btr);
1da177e4 LT	92	mode = btr & 0x3;
2d5eaa6d	93
1da177e4 LT	94	/* If someone decides to do UDMA133 on CSB5 the same
	95	issue will bite so be inclusive */
	96	if (mode > 2 && check_in_drive_lists(drive, svwks_bad_ata100))
	97	mode = 2;
2d5eaa6d BZ	98
2d5eaa6d BZ	99	switch(mode) {
0c824b51	100	case 3: mask = 0x3f; break;
2d5eaa6d BZ	101	case 2: mask = 0x1f; break;
	102	case 1: mask = 0x07; break;
	103	default: mask = 0x00; break;
	104	}
1da177e4 LT	105	}
	106	if (((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) \|\|
	107	(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) &&
	108	(!(PCI_FUNC(dev->devfn) & 1)))
2d5eaa6d BZ	109	mask = 0x1f;
	110
	111	return mask;
1da177e4 LT	112	}
	113
	114	static u8 svwks_csb_check (struct pci_dev *dev)
	115	{
	116	switch (dev->device) {
	117	case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
	118	case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
	119	case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
84f57fbc	120	case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
1da177e4 LT	121	return 1;
	122	default:
	123	break;
	124	}
	125	return 0;
	126	}
1880a8d7	127
88b2b32b	128	static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
1880a8d7 BZ	129	{
	130	static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
	131	static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
	132
36501650	133	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
1880a8d7 BZ	134
	135	pci_write_config_byte(dev, drive_pci[drive->dn], pio_modes[pio]);
	136
	137	if (svwks_csb_check(dev)) {
	138	u16 csb_pio = 0;
	139
	140	pci_read_config_word(dev, 0x4a, &csb_pio);
	141
	142	csb_pio &= ~(0x0f << (4 * drive->dn));
	143	csb_pio \|= (pio << (4 * drive->dn));
	144
	145	pci_write_config_word(dev, 0x4a, csb_pio);
	146	}
	147	}
	148
88b2b32b	149	static void svwks_set_dma_mode(ide_drive_t *drive, const u8 speed)
1da177e4	150	{
f201f504 AC	151	static const u8 udma_modes[] = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
f201f504 AC	152	static const u8 dma_modes[] = { 0x77, 0x21, 0x20 };
f201f504	153	static const u8 drive_pci2[] = { 0x45, 0x44, 0x47, 0x46 };
1da177e4 LT	154
1da177e4 LT	155	ide_hwif_t *hwif = HWIF(drive);
36501650	156	struct pci_dev *dev = to_pci_dev(hwif->dev);
1da177e4	157	u8 unit = (drive->select.b.unit & 0x01);
1880a8d7 BZ	158
	159	u8 ultra_enable = 0, ultra_timing = 0, dma_timing = 0;
	160
1da177e4	161	pci_read_config_byte(dev, (0x56\|hwif->channel), &ultra_timing);
1da177e4 LT	162	pci_read_config_byte(dev, 0x54, &ultra_enable);
1da177e4 LT	163
1da177e4 LT	164	ultra_timing &= ~(0x0F << (4*unit));
1da177e4 LT	165	ultra_enable &= ~(0x01 << drive->dn);
1da177e4	166
7b971df1 BZ	167	if (speed >= XFER_UDMA_0) {
	168	dma_timing \|= dma_modes[2];
	169	ultra_timing \|= (udma_modes[speed - XFER_UDMA_0] << (4 * unit));
	170	ultra_enable \|= (0x01 << drive->dn);
	171	} else if (speed >= XFER_MW_DMA_0)
	172	dma_timing \|= dma_modes[speed - XFER_MW_DMA_0];
1da177e4	173
1da177e4 LT	174	pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
	175	pci_write_config_byte(dev, (0x56\|hwif->channel), ultra_timing);
	176	pci_write_config_byte(dev, 0x54, ultra_enable);
1da177e4 LT	177	}
1da177e4 LT	178
a326b02b	179	static unsigned int __devinit init_chipset_svwks(struct pci_dev *dev)
1da177e4 LT	180	{
	181	unsigned int reg;
	182	u8 btr;
	183
1da177e4 LT	184	/* force Master Latency Timer value to 64 PCICLKs */
	185	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x40);
	186
	187	/* OSB4 : South Bridge and IDE */
	188	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
970a6136	189	isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
1da177e4 LT	190	PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
	191	if (isa_dev) {
	192	pci_read_config_dword(isa_dev, 0x64, &reg);
	193	reg &= ~0x00002000; /* disable 600ns interrupt mask */
	194	if(!(reg & 0x00004000))
a326b02b BZ	195	printk(KERN_DEBUG DRV_NAME " %s: UDMA not BIOS "
a326b02b BZ	196	"enabled.\n", pci_name(dev));
1da177e4 LT	197	reg \|= 0x00004000; /* enable UDMA/33 support */
	198	pci_write_config_dword(isa_dev, 0x64, reg);
	199	}
	200	}
	201
	202	/* setup CSB5/CSB6 : South Bridge and IDE option RAID */
	203	else if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) \|\|
	204	(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) \|\|
	205	(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
	206
	207	/* Third Channel Test */
	208	if (!(PCI_FUNC(dev->devfn) & 1)) {
	209	struct pci_dev * findev = NULL;
	210	u32 reg4c = 0;
970a6136	211	findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
1da177e4 LT	212	PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
	213	if (findev) {
	214	pci_read_config_dword(findev, 0x4C, &reg4c);
	215	reg4c &= ~0x000007FF;
	216	reg4c \|= 0x00000040;
	217	reg4c \|= 0x00000020;
	218	pci_write_config_dword(findev, 0x4C, reg4c);
970a6136	219	pci_dev_put(findev);
1da177e4 LT	220	}
	221	outb_p(0x06, 0x0c00);
	222	dev->irq = inb_p(0x0c01);
1da177e4 LT	223	} else {
	224	struct pci_dev * findev = NULL;
	225	u8 reg41 = 0;
	226
970a6136	227	findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
1da177e4 LT	228	PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
	229	if (findev) {
	230	pci_read_config_byte(findev, 0x41, &reg41);
	231	reg41 &= ~0x40;
	232	pci_write_config_byte(findev, 0x41, reg41);
970a6136	233	pci_dev_put(findev);
1da177e4 LT	234	}
	235	/*
	236	* This is a device pin issue on CSB6.
	237	* Since there will be a future raid mode,
	238	* early versions of the chipset require the
	239	* interrupt pin to be set, and it is a compatibility
	240	* mode issue.
	241	*/
	242	if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
	243	dev->irq = 0;
	244	}
	245	// pci_read_config_dword(dev, 0x40, &pioreg)
	246	// pci_write_config_dword(dev, 0x40, 0x99999999);
	247	// pci_read_config_dword(dev, 0x44, &dmareg);
	248	// pci_write_config_dword(dev, 0x44, 0xFFFFFFFF);
	249	/* setup the UDMA Control register
	250	*
	251	* 1. clear bit 6 to enable DMA
	252	* 2. enable DMA modes with bits 0-1
	253	* 00 : legacy
	254	* 01 : udma2
	255	* 10 : udma2/udma4
	256	* 11 : udma2/udma4/udma5
	257	*/
	258	pci_read_config_byte(dev, 0x5A, &btr);
	259	btr &= ~0x40;
	260	if (!(PCI_FUNC(dev->devfn) & 1))
	261	btr \|= 0x2;
	262	else
44c10138	263	btr \|= (dev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
1da177e4 LT	264	pci_write_config_byte(dev, 0x5A, btr);
1da177e4 LT	265	}
84f57fbc NS	266	/* Setup HT1000 SouthBridge Controller - Single Channel Only */
	267	else if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
	268	pci_read_config_byte(dev, 0x5A, &btr);
	269	btr &= ~0x40;
	270	btr \|= 0x3;
	271	pci_write_config_byte(dev, 0x5A, btr);
	272	}
1da177e4	273
f201f504	274	return dev->irq;
1da177e4 LT	275	}
1da177e4 LT	276
f454cbe8	277	static u8 ata66_svwks_svwks(ide_hwif_t *hwif)
1da177e4	278	{
49521f97	279	return ATA_CBL_PATA80;
1da177e4 LT	280	}
	281
	282	/* On Dell PowerEdge servers with a CSB5/CSB6, the top two bits
	283	* of the subsystem device ID indicate presence of an 80-pin cable.
	284	* Bit 15 clear = secondary IDE channel does not have 80-pin cable.
	285	* Bit 15 set = secondary IDE channel has 80-pin cable.
	286	* Bit 14 clear = primary IDE channel does not have 80-pin cable.
	287	* Bit 14 set = primary IDE channel has 80-pin cable.
	288	*/
f454cbe8	289	static u8 ata66_svwks_dell(ide_hwif_t *hwif)
1da177e4	290	{
36501650 BZ	291	struct pci_dev *dev = to_pci_dev(hwif->dev);
36501650 BZ	292
1da177e4 LT	293	if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
	294	dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
	295	(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE \|\|
	296	dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE))
	297	return ((1 << (hwif->channel + 14)) &
49521f97 BZ	298	dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
49521f97 BZ	299	return ATA_CBL_PATA40;
1da177e4 LT	300	}
	301
	302	/* Sun Cobalt Alpine hardware avoids the 80-pin cable
	303	* detect issue by attaching the drives directly to the board.
	304	* This check follows the Dell precedent (how scary is that?!)
	305	*
	306	* WARNING: this only works on Alpine hardware!
	307	*/
f454cbe8	308	static u8 ata66_svwks_cobalt(ide_hwif_t *hwif)
1da177e4	309	{
36501650 BZ	310	struct pci_dev *dev = to_pci_dev(hwif->dev);
36501650 BZ	311
1da177e4 LT	312	if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
	313	dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
	314	dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
	315	return ((1 << (hwif->channel + 14)) &
49521f97 BZ	316	dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
49521f97 BZ	317	return ATA_CBL_PATA40;
1da177e4 LT	318	}
1da177e4 LT	319
f454cbe8	320	static u8 svwks_cable_detect(ide_hwif_t *hwif)
1da177e4	321	{
36501650	322	struct pci_dev *dev = to_pci_dev(hwif->dev);
1da177e4	323
1da177e4 LT	324	/* Server Works */
	325	if (dev->subsystem_vendor == PCI_VENDOR_ID_SERVERWORKS)
	326	return ata66_svwks_svwks (hwif);
	327
	328	/* Dell PowerEdge */
	329	if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL)
	330	return ata66_svwks_dell (hwif);
	331
	332	/* Cobalt Alpine */
	333	if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN)
	334	return ata66_svwks_cobalt (hwif);
	335
f201f504 AC	336	/* Per Specified Design by OEM, and ASIC Architect */
	337	if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) \|\|
	338	(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2))
49521f97	339	return ATA_CBL_PATA80;
f201f504	340
49521f97	341	return ATA_CBL_PATA40;
1da177e4 LT	342	}
1da177e4 LT	343
ac95beed BZ	344	static const struct ide_port_ops osb4_port_ops = {
	345	.set_pio_mode = svwks_set_pio_mode,
	346	.set_dma_mode = svwks_set_dma_mode,
	347	.udma_filter = svwks_udma_filter,
	348	};
1da177e4	349
ac95beed BZ	350	static const struct ide_port_ops svwks_port_ops = {
	351	.set_pio_mode = svwks_set_pio_mode,
	352	.set_dma_mode = svwks_set_dma_mode,
	353	.udma_filter = svwks_udma_filter,
	354	.cable_detect = svwks_cable_detect,
	355	};
1da177e4	356
3b2a5c71	357	#define IDE_HFLAGS_SVWKS IDE_HFLAG_LEGACY_IRQS
4db90a14	358
85620436	359	static const struct ide_port_info serverworks_chipsets[] __devinitdata = {
ced3ec8a BZ	360	{ /* 0: OSB4 */
ced3ec8a BZ	361	.name = DRV_NAME,
1da177e4	362	.init_chipset = init_chipset_svwks,
ac95beed	363	.port_ops = &osb4_port_ops,
4db90a14	364	.host_flags = IDE_HFLAGS_SVWKS,
4099d143	365	.pio_mask = ATA_PIO4,
5f8b6c34 BZ	366	.mwdma_mask = ATA_MWDMA2,
5f8b6c34 BZ	367	.udma_mask = 0x00, /* UDMA is problematic on OSB4 */
ced3ec8a BZ	368	},
	369	{ /* 1: CSB5 */
	370	.name = DRV_NAME,
1da177e4	371	.init_chipset = init_chipset_svwks,
ac95beed	372	.port_ops = &svwks_port_ops,
4db90a14	373	.host_flags = IDE_HFLAGS_SVWKS,
4099d143	374	.pio_mask = ATA_PIO4,
5f8b6c34 BZ	375	.mwdma_mask = ATA_MWDMA2,
5f8b6c34 BZ	376	.udma_mask = ATA_UDMA5,
ced3ec8a BZ	377	},
	378	{ /* 2: CSB6 */
	379	.name = DRV_NAME,
1da177e4	380	.init_chipset = init_chipset_svwks,
ac95beed	381	.port_ops = &svwks_port_ops,
4db90a14	382	.host_flags = IDE_HFLAGS_SVWKS,
4099d143	383	.pio_mask = ATA_PIO4,
5f8b6c34 BZ	384	.mwdma_mask = ATA_MWDMA2,
5f8b6c34 BZ	385	.udma_mask = ATA_UDMA5,
ced3ec8a BZ	386	},
	387	{ /* 3: CSB6-2 */
	388	.name = DRV_NAME,
1da177e4	389	.init_chipset = init_chipset_svwks,
ac95beed	390	.port_ops = &svwks_port_ops,
4db90a14	391	.host_flags = IDE_HFLAGS_SVWKS \| IDE_HFLAG_SINGLE,
4099d143	392	.pio_mask = ATA_PIO4,
5f8b6c34 BZ	393	.mwdma_mask = ATA_MWDMA2,
5f8b6c34 BZ	394	.udma_mask = ATA_UDMA5,
ced3ec8a BZ	395	},
	396	{ /* 4: HT1000 */
	397	.name = DRV_NAME,
84f57fbc	398	.init_chipset = init_chipset_svwks,
ac95beed	399	.port_ops = &svwks_port_ops,
4db90a14	400	.host_flags = IDE_HFLAGS_SVWKS \| IDE_HFLAG_SINGLE,
4099d143	401	.pio_mask = ATA_PIO4,
5f8b6c34 BZ	402	.mwdma_mask = ATA_MWDMA2,
5f8b6c34 BZ	403	.udma_mask = ATA_UDMA5,
1da177e4 LT	404	}
	405	};
	406
	407	/**
	408	* svwks_init_one - called when a OSB/CSB is found
	409	* @dev: the svwks device
	410	* @id: the matching pci id
	411	*
	412	* Called when the PCI registration layer (or the IDE initialization)
	413	* finds a device matching our IDE device tables.
	414	*/
	415
	416	static int __devinit svwks_init_one(struct pci_dev dev, const struct pci_device_id id)
	417	{
039788e1	418	struct ide_port_info d;
7ed58297 BZ	419	u8 idx = id->driver_data;
	420
	421	d = serverworks_chipsets[idx];
	422
8ac2b42a BZ	423	if (idx == 1)
	424	d.host_flags \|= IDE_HFLAG_CLEAR_SIMPLEX;
	425	else if (idx == 2 \|\| idx == 3) {
7ed58297 BZ	426	if ((PCI_FUNC(dev->devfn) & 1) == 0) {
7ed58297 BZ	427	if (pci_resource_start(dev, 0) != 0x01f1)
5e71d9c5	428	d.host_flags \|= IDE_HFLAG_NON_BOOTABLE;
7ed58297 BZ	429	d.host_flags \|= IDE_HFLAG_SINGLE;
	430	} else
	431	d.host_flags &= ~IDE_HFLAG_SINGLE;
	432	}
1da177e4	433
6cdf6eb3	434	return ide_pci_init_one(dev, &d, NULL);
1da177e4 LT	435	}
1da177e4 LT	436
9cbcc5e3 BZ	437	static const struct pci_device_id svwks_pci_tbl[] = {
	438	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0 },
	439	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 1 },
	440	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2 },
	441	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 3 },
	442	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 4 },
1da177e4 LT	443	{ 0, },
	444	};
	445	MODULE_DEVICE_TABLE(pci, svwks_pci_tbl);
	446
	447	static struct pci_driver driver = {
	448	.name = "Serverworks_IDE",
	449	.id_table = svwks_pci_tbl,
	450	.probe = svwks_init_one,
bc2c9a80	451	.remove = ide_pci_remove,
1da177e4 LT	452	};
1da177e4 LT	453
82ab1eec	454	static int __init svwks_ide_init(void)
1da177e4 LT	455	{
	456	return ide_pci_register_driver(&driver);
	457	}
	458
bc2c9a80 BZ	459	static void __exit svwks_ide_exit(void)
	460	{
	461	pci_unregister_driver(&driver);
	462	}
	463
1da177e4	464	module_init(svwks_ide_init);
bc2c9a80	465	module_exit(svwks_ide_exit);
1da177e4 LT	466
	467	MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick");
	468	MODULE_DESCRIPTION("PCI driver module for Serverworks OSB4/CSB5/CSB6 IDE");
	469	MODULE_LICENSE("GPL");