Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* Intel EtherExpress 16 device driver for Linux |
2 | * | |
3 | * Written by John Sullivan, 1995 | |
4 | * based on original code by Donald Becker, with changes by | |
5 | * Alan Cox and Pauline Middelink. | |
6 | * | |
7 | * Support for 8-bit mode by Zoltan Szilagyi <zoltans@cs.arizona.edu> | |
8 | * | |
9 | * Many modifications, and currently maintained, by | |
10 | * Philip Blundell <philb@gnu.org> | |
11 | * Added the Compaq LTE Alan Cox <alan@redhat.com> | |
12 | * Added MCA support Adam Fritzler <mid@auk.cx> | |
13 | * | |
14 | * Note - this driver is experimental still - it has problems on faster | |
15 | * machines. Someone needs to sit down and go through it line by line with | |
16 | * a databook... | |
17 | */ | |
18 | ||
19 | /* The EtherExpress 16 is a fairly simple card, based on a shared-memory | |
20 | * design using the i82586 Ethernet coprocessor. It bears no relationship, | |
21 | * as far as I know, to the similarly-named "EtherExpress Pro" range. | |
22 | * | |
23 | * Historically, Linux support for these cards has been very bad. However, | |
24 | * things seem to be getting better slowly. | |
25 | */ | |
26 | ||
27 | /* If your card is confused about what sort of interface it has (eg it | |
28 | * persistently reports "10baseT" when none is fitted), running 'SOFTSET /BART' | |
29 | * or 'SOFTSET /LISA' from DOS seems to help. | |
30 | */ | |
31 | ||
32 | /* Here's the scoop on memory mapping. | |
33 | * | |
34 | * There are three ways to access EtherExpress card memory: either using the | |
35 | * shared-memory mapping, or using PIO through the dataport, or using PIO | |
36 | * through the "shadow memory" ports. | |
37 | * | |
38 | * The shadow memory system works by having the card map some of its memory | |
39 | * as follows: | |
40 | * | |
41 | * (the low five bits of the SMPTR are ignored) | |
42 | * | |
43 | * base+0x4000..400f memory at SMPTR+0..15 | |
44 | * base+0x8000..800f memory at SMPTR+16..31 | |
45 | * base+0xc000..c007 dubious stuff (memory at SMPTR+16..23 apparently) | |
46 | * base+0xc008..c00f memory at 0x0008..0x000f | |
47 | * | |
48 | * This last set (the one at c008) is particularly handy because the SCB | |
49 | * lives at 0x0008. So that set of ports gives us easy random access to data | |
50 | * in the SCB without having to mess around setting up pointers and the like. | |
51 | * We always use this method to access the SCB (via the scb_xx() functions). | |
52 | * | |
53 | * Dataport access works by aiming the appropriate (read or write) pointer | |
54 | * at the first address you're interested in, and then reading or writing from | |
55 | * the dataport. The pointers auto-increment after each transfer. We use | |
56 | * this for data transfer. | |
57 | * | |
58 | * We don't use the shared-memory system because it allegedly doesn't work on | |
59 | * all cards, and because it's a bit more prone to go wrong (it's one more | |
60 | * thing to configure...). | |
61 | */ | |
62 | ||
63 | /* Known bugs: | |
64 | * | |
65 | * - The card seems to want to give us two interrupts every time something | |
66 | * happens, where just one would be better. | |
67 | */ | |
68 | ||
69 | /* | |
70 | * | |
71 | * Note by Zoltan Szilagyi 10-12-96: | |
72 | * | |
73 | * I've succeeded in eliminating the "CU wedged" messages, and hence the | |
74 | * lockups, which were only occurring with cards running in 8-bit mode ("force | |
75 | * 8-bit operation" in Intel's SoftSet utility). This version of the driver | |
76 | * sets the 82586 and the ASIC to 8-bit mode at startup; it also stops the | |
77 | * CU before submitting a packet for transmission, and then restarts it as soon | |
78 | * as the process of handing the packet is complete. This is definitely an | |
79 | * unnecessary slowdown if the card is running in 16-bit mode; therefore one | |
6aa20a22 | 80 | * should detect 16-bit vs 8-bit mode from the EEPROM settings and act |
1da177e4 LT |
81 | * accordingly. In 8-bit mode with this bugfix I'm getting about 150 K/s for |
82 | * ftp's, which is significantly better than I get in DOS, so the overhead of | |
83 | * stopping and restarting the CU with each transmit is not prohibitive in | |
84 | * practice. | |
85 | * | |
86 | * Update by David Woodhouse 11/5/99: | |
87 | * | |
88 | * I've seen "CU wedged" messages in 16-bit mode, on the Alpha architecture. | |
89 | * I assume that this is because 16-bit accesses are actually handled as two | |
90 | * 8-bit accesses. | |
91 | */ | |
92 | ||
93 | #ifdef __alpha__ | |
94 | #define LOCKUP16 1 | |
95 | #endif | |
96 | #ifndef LOCKUP16 | |
97 | #define LOCKUP16 0 | |
98 | #endif | |
6aa20a22 | 99 | |
1da177e4 LT |
100 | #include <linux/module.h> |
101 | #include <linux/kernel.h> | |
102 | #include <linux/types.h> | |
103 | #include <linux/fcntl.h> | |
104 | #include <linux/interrupt.h> | |
105 | #include <linux/ioport.h> | |
106 | #include <linux/string.h> | |
107 | #include <linux/in.h> | |
108 | #include <linux/delay.h> | |
109 | #include <linux/errno.h> | |
110 | #include <linux/init.h> | |
111 | #include <linux/netdevice.h> | |
112 | #include <linux/etherdevice.h> | |
113 | #include <linux/skbuff.h> | |
114 | #include <linux/slab.h> | |
115 | #include <linux/mca-legacy.h> | |
116 | #include <linux/spinlock.h> | |
117 | #include <linux/bitops.h> | |
118 | ||
119 | #include <asm/system.h> | |
120 | #include <asm/io.h> | |
121 | #include <asm/irq.h> | |
122 | ||
123 | #ifndef NET_DEBUG | |
124 | #define NET_DEBUG 4 | |
125 | #endif | |
126 | ||
127 | #include "eexpress.h" | |
128 | ||
129 | #define EEXP_IO_EXTENT 16 | |
130 | ||
131 | /* | |
132 | * Private data declarations | |
133 | */ | |
134 | ||
135 | struct net_local | |
136 | { | |
137 | struct net_device_stats stats; | |
138 | unsigned long last_tx; /* jiffies when last transmit started */ | |
139 | unsigned long init_time; /* jiffies when eexp_hw_init586 called */ | |
140 | unsigned short rx_first; /* first rx buf, same as RX_BUF_START */ | |
141 | unsigned short rx_last; /* last rx buf */ | |
142 | unsigned short rx_ptr; /* first rx buf to look at */ | |
143 | unsigned short tx_head; /* next free tx buf */ | |
144 | unsigned short tx_reap; /* first in-use tx buf */ | |
145 | unsigned short tx_tail; /* previous tx buf to tx_head */ | |
146 | unsigned short tx_link; /* last known-executing tx buf */ | |
147 | unsigned short last_tx_restart; /* set to tx_link when we | |
148 | restart the CU */ | |
149 | unsigned char started; | |
150 | unsigned short rx_buf_start; | |
151 | unsigned short rx_buf_end; | |
152 | unsigned short num_tx_bufs; | |
153 | unsigned short num_rx_bufs; | |
154 | unsigned char width; /* 0 for 16bit, 1 for 8bit */ | |
155 | unsigned char was_promisc; | |
156 | unsigned char old_mc_count; | |
157 | spinlock_t lock; | |
158 | }; | |
159 | ||
160 | /* This is the code and data that is downloaded to the EtherExpress card's | |
161 | * memory at boot time. | |
162 | */ | |
163 | ||
164 | static unsigned short start_code[] = { | |
165 | /* 0x0000 */ | |
166 | 0x0001, /* ISCP: busy - cleared after reset */ | |
167 | 0x0008,0x0000,0x0000, /* offset,address (lo,hi) of SCB */ | |
168 | ||
169 | 0x0000,0x0000, /* SCB: status, commands */ | |
170 | 0x0000,0x0000, /* links to first command block, | |
171 | first receive descriptor */ | |
172 | 0x0000,0x0000, /* CRC error, alignment error counts */ | |
173 | 0x0000,0x0000, /* out of resources, overrun error counts */ | |
174 | ||
175 | 0x0000,0x0000, /* pad */ | |
176 | 0x0000,0x0000, | |
177 | ||
178 | /* 0x20 -- start of 82586 CU program */ | |
179 | #define CONF_LINK 0x20 | |
6aa20a22 | 180 | 0x0000,Cmd_Config, |
1da177e4 LT |
181 | 0x0032, /* link to next command */ |
182 | 0x080c, /* 12 bytes follow : fifo threshold=8 */ | |
183 | 0x2e40, /* don't rx bad frames | |
184 | * SRDY/ARDY => ext. sync. : preamble len=8 | |
185 | * take addresses from data buffers | |
186 | * 6 bytes/address | |
187 | */ | |
188 | 0x6000, /* default backoff method & priority | |
189 | * interframe spacing = 0x60 */ | |
6aa20a22 | 190 | 0xf200, /* slot time=0x200 |
1da177e4 LT |
191 | * max collision retry = 0xf */ |
192 | #define CONF_PROMISC 0x2e | |
6aa20a22 | 193 | 0x0000, /* no HDLC : normal CRC : enable broadcast |
1da177e4 LT |
194 | * disable promiscuous/multicast modes */ |
195 | 0x003c, /* minimum frame length = 60 octets) */ | |
196 | ||
197 | 0x0000,Cmd_SetAddr, | |
198 | 0x003e, /* link to next command */ | |
199 | #define CONF_HWADDR 0x38 | |
200 | 0x0000,0x0000,0x0000, /* hardware address placed here */ | |
201 | ||
202 | 0x0000,Cmd_MCast, | |
203 | 0x0076, /* link to next command */ | |
204 | #define CONF_NR_MULTICAST 0x44 | |
205 | 0x0000, /* number of multicast addresses */ | |
206 | #define CONF_MULTICAST 0x46 | |
207 | 0x0000, 0x0000, 0x0000, /* some addresses */ | |
208 | 0x0000, 0x0000, 0x0000, | |
209 | 0x0000, 0x0000, 0x0000, | |
210 | 0x0000, 0x0000, 0x0000, | |
211 | 0x0000, 0x0000, 0x0000, | |
212 | 0x0000, 0x0000, 0x0000, | |
213 | 0x0000, 0x0000, 0x0000, | |
214 | 0x0000, 0x0000, 0x0000, | |
215 | ||
216 | #define CONF_DIAG_RESULT 0x76 | |
217 | 0x0000, Cmd_Diag, | |
218 | 0x007c, /* link to next command */ | |
219 | ||
220 | 0x0000,Cmd_TDR|Cmd_INT, | |
221 | 0x0084, | |
222 | #define CONF_TDR_RESULT 0x82 | |
223 | 0x0000, | |
224 | ||
225 | 0x0000,Cmd_END|Cmd_Nop, /* end of configure sequence */ | |
226 | 0x0084 /* dummy link */ | |
227 | }; | |
228 | ||
229 | /* maps irq number to EtherExpress magic value */ | |
230 | static char irqrmap[] = { 0,0,1,2,3,4,0,0,0,1,5,6,0,0,0,0 }; | |
231 | ||
232 | #ifdef CONFIG_MCA_LEGACY | |
233 | /* mapping of the first four bits of the second POS register */ | |
234 | static unsigned short mca_iomap[] = { | |
235 | 0x270, 0x260, 0x250, 0x240, 0x230, 0x220, 0x210, 0x200, | |
236 | 0x370, 0x360, 0x350, 0x340, 0x330, 0x320, 0x310, 0x300 | |
237 | }; | |
238 | /* bits 5-7 of the second POS register */ | |
239 | static char mca_irqmap[] = { 12, 9, 3, 4, 5, 10, 11, 15 }; | |
6aa20a22 | 240 | #endif |
1da177e4 LT |
241 | |
242 | /* | |
243 | * Prototypes for Linux interface | |
244 | */ | |
245 | ||
246 | static int eexp_open(struct net_device *dev); | |
247 | static int eexp_close(struct net_device *dev); | |
248 | static void eexp_timeout(struct net_device *dev); | |
249 | static struct net_device_stats *eexp_stats(struct net_device *dev); | |
250 | static int eexp_xmit(struct sk_buff *buf, struct net_device *dev); | |
251 | ||
7d12e780 | 252 | static irqreturn_t eexp_irq(int irq, void *dev_addr); |
1da177e4 LT |
253 | static void eexp_set_multicast(struct net_device *dev); |
254 | ||
255 | /* | |
256 | * Prototypes for hardware access functions | |
257 | */ | |
258 | ||
259 | static void eexp_hw_rx_pio(struct net_device *dev); | |
260 | static void eexp_hw_tx_pio(struct net_device *dev, unsigned short *buf, | |
261 | unsigned short len); | |
262 | static int eexp_hw_probe(struct net_device *dev,unsigned short ioaddr); | |
263 | static unsigned short eexp_hw_readeeprom(unsigned short ioaddr, | |
264 | unsigned char location); | |
265 | ||
266 | static unsigned short eexp_hw_lasttxstat(struct net_device *dev); | |
267 | static void eexp_hw_txrestart(struct net_device *dev); | |
268 | ||
269 | static void eexp_hw_txinit (struct net_device *dev); | |
270 | static void eexp_hw_rxinit (struct net_device *dev); | |
271 | ||
272 | static void eexp_hw_init586 (struct net_device *dev); | |
273 | static void eexp_setup_filter (struct net_device *dev); | |
274 | ||
275 | static char *eexp_ifmap[]={"AUI", "BNC", "RJ45"}; | |
276 | enum eexp_iftype {AUI=0, BNC=1, TPE=2}; | |
277 | ||
278 | #define STARTED_RU 2 | |
279 | #define STARTED_CU 1 | |
280 | ||
281 | /* | |
282 | * Primitive hardware access functions. | |
283 | */ | |
284 | ||
285 | static inline unsigned short scb_status(struct net_device *dev) | |
286 | { | |
287 | return inw(dev->base_addr + 0xc008); | |
288 | } | |
289 | ||
290 | static inline unsigned short scb_rdcmd(struct net_device *dev) | |
291 | { | |
292 | return inw(dev->base_addr + 0xc00a); | |
293 | } | |
294 | ||
295 | static inline void scb_command(struct net_device *dev, unsigned short cmd) | |
296 | { | |
297 | outw(cmd, dev->base_addr + 0xc00a); | |
298 | } | |
299 | ||
300 | static inline void scb_wrcbl(struct net_device *dev, unsigned short val) | |
301 | { | |
302 | outw(val, dev->base_addr + 0xc00c); | |
303 | } | |
304 | ||
305 | static inline void scb_wrrfa(struct net_device *dev, unsigned short val) | |
306 | { | |
307 | outw(val, dev->base_addr + 0xc00e); | |
308 | } | |
309 | ||
310 | static inline void set_loopback(struct net_device *dev) | |
311 | { | |
312 | outb(inb(dev->base_addr + Config) | 2, dev->base_addr + Config); | |
313 | } | |
314 | ||
315 | static inline void clear_loopback(struct net_device *dev) | |
316 | { | |
317 | outb(inb(dev->base_addr + Config) & ~2, dev->base_addr + Config); | |
318 | } | |
319 | ||
320 | static inline unsigned short int SHADOW(short int addr) | |
321 | { | |
322 | addr &= 0x1f; | |
323 | if (addr > 0xf) addr += 0x3ff0; | |
324 | return addr + 0x4000; | |
325 | } | |
326 | ||
327 | /* | |
328 | * Linux interface | |
329 | */ | |
330 | ||
331 | /* | |
332 | * checks for presence of EtherExpress card | |
333 | */ | |
334 | ||
335 | static int __init do_express_probe(struct net_device *dev) | |
336 | { | |
337 | unsigned short *port; | |
338 | static unsigned short ports[] = { 0x240,0x300,0x310,0x270,0x320,0x340,0 }; | |
339 | unsigned short ioaddr = dev->base_addr; | |
340 | int dev_irq = dev->irq; | |
341 | int err; | |
342 | ||
343 | SET_MODULE_OWNER(dev); | |
344 | ||
345 | dev->if_port = 0xff; /* not set */ | |
346 | ||
347 | #ifdef CONFIG_MCA_LEGACY | |
348 | if (MCA_bus) { | |
349 | int slot = 0; | |
350 | ||
351 | /* | |
352 | * Only find one card at a time. Subsequent calls | |
353 | * will find others, however, proper multicard MCA | |
354 | * probing and setup can't be done with the | |
355 | * old-style Space.c init routines. -- ASF | |
356 | */ | |
357 | while (slot != MCA_NOTFOUND) { | |
358 | int pos0, pos1; | |
6aa20a22 | 359 | |
1da177e4 LT |
360 | slot = mca_find_unused_adapter(0x628B, slot); |
361 | if (slot == MCA_NOTFOUND) | |
362 | break; | |
363 | ||
364 | pos0 = mca_read_stored_pos(slot, 2); | |
365 | pos1 = mca_read_stored_pos(slot, 3); | |
366 | ioaddr = mca_iomap[pos1&0xf]; | |
367 | ||
368 | dev->irq = mca_irqmap[(pos1>>4)&0x7]; | |
6aa20a22 | 369 | |
1da177e4 LT |
370 | /* |
371 | * XXX: Transciever selection is done | |
6aa20a22 | 372 | * differently on the MCA version. |
1da177e4 LT |
373 | * How to get it to select something |
374 | * other than external/AUI is currently | |
375 | * unknown. This code is just for looks. -- ASF | |
376 | */ | |
377 | if ((pos0 & 0x7) == 0x1) | |
378 | dev->if_port = AUI; | |
379 | else if ((pos0 & 0x7) == 0x5) { | |
380 | if (pos1 & 0x80) | |
381 | dev->if_port = BNC; | |
382 | else | |
383 | dev->if_port = TPE; | |
384 | } | |
385 | ||
386 | mca_set_adapter_name(slot, "Intel EtherExpress 16 MCA"); | |
387 | mca_set_adapter_procfn(slot, NULL, dev); | |
388 | mca_mark_as_used(slot); | |
389 | ||
390 | break; | |
391 | } | |
392 | } | |
393 | #endif | |
394 | if (ioaddr&0xfe00) { | |
395 | if (!request_region(ioaddr, EEXP_IO_EXTENT, "EtherExpress")) | |
396 | return -EBUSY; | |
397 | err = eexp_hw_probe(dev,ioaddr); | |
398 | release_region(ioaddr, EEXP_IO_EXTENT); | |
399 | return err; | |
400 | } else if (ioaddr) | |
401 | return -ENXIO; | |
402 | ||
403 | for (port=&ports[0] ; *port ; port++ ) | |
404 | { | |
405 | unsigned short sum = 0; | |
406 | int i; | |
407 | if (!request_region(*port, EEXP_IO_EXTENT, "EtherExpress")) | |
408 | continue; | |
409 | for ( i=0 ; i<4 ; i++ ) | |
410 | { | |
411 | unsigned short t; | |
412 | t = inb(*port + ID_PORT); | |
413 | sum |= (t>>4) << ((t & 0x03)<<2); | |
414 | } | |
415 | if (sum==0xbaba && !eexp_hw_probe(dev,*port)) { | |
416 | release_region(*port, EEXP_IO_EXTENT); | |
417 | return 0; | |
418 | } | |
419 | release_region(*port, EEXP_IO_EXTENT); | |
420 | dev->irq = dev_irq; | |
421 | } | |
422 | return -ENODEV; | |
423 | } | |
424 | ||
425 | #ifndef MODULE | |
426 | struct net_device * __init express_probe(int unit) | |
427 | { | |
428 | struct net_device *dev = alloc_etherdev(sizeof(struct net_local)); | |
429 | int err; | |
430 | ||
431 | if (!dev) | |
432 | return ERR_PTR(-ENOMEM); | |
433 | ||
434 | sprintf(dev->name, "eth%d", unit); | |
435 | netdev_boot_setup_check(dev); | |
436 | ||
437 | err = do_express_probe(dev); | |
b1fc5505 | 438 | if (!err) |
439 | return dev; | |
1da177e4 LT |
440 | free_netdev(dev); |
441 | return ERR_PTR(err); | |
442 | } | |
443 | #endif | |
444 | ||
445 | /* | |
446 | * open and initialize the adapter, ready for use | |
447 | */ | |
448 | ||
449 | static int eexp_open(struct net_device *dev) | |
450 | { | |
451 | int ret; | |
452 | unsigned short ioaddr = dev->base_addr; | |
453 | struct net_local *lp = netdev_priv(dev); | |
454 | ||
455 | #if NET_DEBUG > 6 | |
456 | printk(KERN_DEBUG "%s: eexp_open()\n", dev->name); | |
457 | #endif | |
458 | ||
459 | if (!dev->irq || !irqrmap[dev->irq]) | |
460 | return -ENXIO; | |
461 | ||
462 | ret = request_irq(dev->irq,&eexp_irq,0,dev->name,dev); | |
463 | if (ret) return ret; | |
464 | ||
465 | if (!request_region(ioaddr, EEXP_IO_EXTENT, "EtherExpress")) { | |
466 | printk(KERN_WARNING "EtherExpress io port %x, is busy.\n" | |
467 | , ioaddr); | |
468 | goto err_out1; | |
469 | } | |
470 | if (!request_region(ioaddr+0x4000, EEXP_IO_EXTENT, "EtherExpress shadow")) { | |
471 | printk(KERN_WARNING "EtherExpress io port %x, is busy.\n" | |
472 | , ioaddr+0x4000); | |
473 | goto err_out2; | |
474 | } | |
475 | if (!request_region(ioaddr+0x8000, EEXP_IO_EXTENT, "EtherExpress shadow")) { | |
476 | printk(KERN_WARNING "EtherExpress io port %x, is busy.\n" | |
477 | , ioaddr+0x8000); | |
478 | goto err_out3; | |
479 | } | |
480 | if (!request_region(ioaddr+0xc000, EEXP_IO_EXTENT, "EtherExpress shadow")) { | |
481 | printk(KERN_WARNING "EtherExpress io port %x, is busy.\n" | |
482 | , ioaddr+0xc000); | |
483 | goto err_out4; | |
484 | } | |
6aa20a22 | 485 | |
1da177e4 LT |
486 | if (lp->width) { |
487 | printk("%s: forcing ASIC to 8-bit mode\n", dev->name); | |
488 | outb(inb(dev->base_addr+Config)&~4, dev->base_addr+Config); | |
489 | } | |
490 | ||
491 | eexp_hw_init586(dev); | |
492 | netif_start_queue(dev); | |
493 | #if NET_DEBUG > 6 | |
494 | printk(KERN_DEBUG "%s: leaving eexp_open()\n", dev->name); | |
495 | #endif | |
496 | return 0; | |
497 | ||
498 | err_out4: | |
499 | release_region(ioaddr+0x8000, EEXP_IO_EXTENT); | |
500 | err_out3: | |
501 | release_region(ioaddr+0x4000, EEXP_IO_EXTENT); | |
502 | err_out2: | |
503 | release_region(ioaddr, EEXP_IO_EXTENT); | |
504 | err_out1: | |
505 | free_irq(dev->irq, dev); | |
506 | return -EBUSY; | |
507 | } | |
508 | ||
509 | /* | |
510 | * close and disable the interface, leaving the 586 in reset. | |
511 | */ | |
512 | ||
513 | static int eexp_close(struct net_device *dev) | |
514 | { | |
515 | unsigned short ioaddr = dev->base_addr; | |
516 | struct net_local *lp = netdev_priv(dev); | |
517 | ||
518 | int irq = dev->irq; | |
519 | ||
520 | netif_stop_queue(dev); | |
6aa20a22 | 521 | |
1da177e4 LT |
522 | outb(SIRQ_dis|irqrmap[irq],ioaddr+SET_IRQ); |
523 | lp->started = 0; | |
524 | scb_command(dev, SCB_CUsuspend|SCB_RUsuspend); | |
525 | outb(0,ioaddr+SIGNAL_CA); | |
526 | free_irq(irq,dev); | |
527 | outb(i586_RST,ioaddr+EEPROM_Ctrl); | |
528 | release_region(ioaddr, EEXP_IO_EXTENT); | |
529 | release_region(ioaddr+0x4000, 16); | |
530 | release_region(ioaddr+0x8000, 16); | |
531 | release_region(ioaddr+0xc000, 16); | |
532 | ||
533 | return 0; | |
534 | } | |
535 | ||
536 | /* | |
537 | * Return interface stats | |
538 | */ | |
539 | ||
540 | static struct net_device_stats *eexp_stats(struct net_device *dev) | |
541 | { | |
542 | struct net_local *lp = netdev_priv(dev); | |
543 | ||
544 | return &lp->stats; | |
545 | } | |
546 | ||
547 | /* | |
548 | * This gets called when a higher level thinks we are broken. Check that | |
549 | * nothing has become jammed in the CU. | |
550 | */ | |
551 | ||
552 | static void unstick_cu(struct net_device *dev) | |
553 | { | |
554 | struct net_local *lp = netdev_priv(dev); | |
555 | unsigned short ioaddr = dev->base_addr; | |
556 | ||
557 | if (lp->started) | |
558 | { | |
559 | if ((jiffies - dev->trans_start)>50) | |
560 | { | |
561 | if (lp->tx_link==lp->last_tx_restart) | |
562 | { | |
563 | unsigned short boguscount=200,rsst; | |
564 | printk(KERN_WARNING "%s: Retransmit timed out, status %04x, resetting...\n", | |
565 | dev->name, scb_status(dev)); | |
566 | eexp_hw_txinit(dev); | |
567 | lp->last_tx_restart = 0; | |
568 | scb_wrcbl(dev, lp->tx_link); | |
569 | scb_command(dev, SCB_CUstart); | |
570 | outb(0,ioaddr+SIGNAL_CA); | |
571 | while (!SCB_complete(rsst=scb_status(dev))) | |
572 | { | |
573 | if (!--boguscount) | |
574 | { | |
575 | boguscount=200; | |
576 | printk(KERN_WARNING "%s: Reset timed out status %04x, retrying...\n", | |
577 | dev->name,rsst); | |
578 | scb_wrcbl(dev, lp->tx_link); | |
579 | scb_command(dev, SCB_CUstart); | |
580 | outb(0,ioaddr+SIGNAL_CA); | |
581 | } | |
582 | } | |
583 | netif_wake_queue(dev); | |
584 | } | |
585 | else | |
586 | { | |
587 | unsigned short status = scb_status(dev); | |
588 | if (SCB_CUdead(status)) | |
589 | { | |
590 | unsigned short txstatus = eexp_hw_lasttxstat(dev); | |
591 | printk(KERN_WARNING "%s: Transmit timed out, CU not active status %04x %04x, restarting...\n", | |
592 | dev->name, status, txstatus); | |
593 | eexp_hw_txrestart(dev); | |
594 | } | |
595 | else | |
596 | { | |
597 | unsigned short txstatus = eexp_hw_lasttxstat(dev); | |
598 | if (netif_queue_stopped(dev) && !txstatus) | |
599 | { | |
600 | printk(KERN_WARNING "%s: CU wedged, status %04x %04x, resetting...\n", | |
601 | dev->name,status,txstatus); | |
602 | eexp_hw_init586(dev); | |
603 | netif_wake_queue(dev); | |
604 | } | |
605 | else | |
606 | { | |
607 | printk(KERN_WARNING "%s: transmit timed out\n", dev->name); | |
608 | } | |
609 | } | |
610 | } | |
611 | } | |
612 | } | |
613 | else | |
614 | { | |
615 | if ((jiffies-lp->init_time)>10) | |
616 | { | |
617 | unsigned short status = scb_status(dev); | |
618 | printk(KERN_WARNING "%s: i82586 startup timed out, status %04x, resetting...\n", | |
619 | dev->name, status); | |
620 | eexp_hw_init586(dev); | |
621 | netif_wake_queue(dev); | |
622 | } | |
623 | } | |
624 | } | |
625 | ||
626 | static void eexp_timeout(struct net_device *dev) | |
627 | { | |
628 | struct net_local *lp = netdev_priv(dev); | |
629 | #ifdef CONFIG_SMP | |
630 | unsigned long flags; | |
631 | #endif | |
632 | int status; | |
6aa20a22 | 633 | |
1da177e4 LT |
634 | disable_irq(dev->irq); |
635 | ||
636 | /* | |
637 | * Best would be to use synchronize_irq(); spin_lock() here | |
638 | * lets make it work first.. | |
639 | */ | |
6aa20a22 | 640 | |
1da177e4 LT |
641 | #ifdef CONFIG_SMP |
642 | spin_lock_irqsave(&lp->lock, flags); | |
643 | #endif | |
644 | ||
645 | status = scb_status(dev); | |
646 | unstick_cu(dev); | |
647 | printk(KERN_INFO "%s: transmit timed out, %s?\n", dev->name, | |
648 | (SCB_complete(status)?"lost interrupt": | |
649 | "board on fire")); | |
650 | lp->stats.tx_errors++; | |
651 | lp->last_tx = jiffies; | |
652 | if (!SCB_complete(status)) { | |
653 | scb_command(dev, SCB_CUabort); | |
654 | outb(0,dev->base_addr+SIGNAL_CA); | |
655 | } | |
6aa20a22 | 656 | netif_wake_queue(dev); |
1da177e4 LT |
657 | #ifdef CONFIG_SMP |
658 | spin_unlock_irqrestore(&lp->lock, flags); | |
659 | #endif | |
660 | } | |
661 | ||
662 | /* | |
663 | * Called to transmit a packet, or to allow us to right ourselves | |
664 | * if the kernel thinks we've died. | |
665 | */ | |
666 | static int eexp_xmit(struct sk_buff *buf, struct net_device *dev) | |
667 | { | |
668 | struct net_local *lp = netdev_priv(dev); | |
669 | short length = buf->len; | |
670 | #ifdef CONFIG_SMP | |
671 | unsigned long flags; | |
672 | #endif | |
673 | ||
674 | #if NET_DEBUG > 6 | |
675 | printk(KERN_DEBUG "%s: eexp_xmit()\n", dev->name); | |
676 | #endif | |
677 | ||
678 | if (buf->len < ETH_ZLEN) { | |
5b057c6b | 679 | if (skb_padto(buf, ETH_ZLEN)) |
1da177e4 LT |
680 | return 0; |
681 | length = ETH_ZLEN; | |
682 | } | |
683 | ||
684 | disable_irq(dev->irq); | |
685 | ||
686 | /* | |
687 | * Best would be to use synchronize_irq(); spin_lock() here | |
688 | * lets make it work first.. | |
689 | */ | |
6aa20a22 | 690 | |
1da177e4 LT |
691 | #ifdef CONFIG_SMP |
692 | spin_lock_irqsave(&lp->lock, flags); | |
693 | #endif | |
6aa20a22 | 694 | |
1da177e4 LT |
695 | { |
696 | unsigned short *data = (unsigned short *)buf->data; | |
697 | ||
698 | lp->stats.tx_bytes += length; | |
699 | ||
700 | eexp_hw_tx_pio(dev,data,length); | |
701 | } | |
702 | dev_kfree_skb(buf); | |
703 | #ifdef CONFIG_SMP | |
704 | spin_unlock_irqrestore(&lp->lock, flags); | |
705 | #endif | |
706 | enable_irq(dev->irq); | |
707 | return 0; | |
708 | } | |
709 | ||
710 | /* | |
711 | * Handle an EtherExpress interrupt | |
712 | * If we've finished initializing, start the RU and CU up. | |
713 | * If we've already started, reap tx buffers, handle any received packets, | |
714 | * check to make sure we've not become wedged. | |
715 | */ | |
716 | ||
717 | /* | |
718 | * Handle an EtherExpress interrupt | |
719 | * If we've finished initializing, start the RU and CU up. | |
720 | * If we've already started, reap tx buffers, handle any received packets, | |
721 | * check to make sure we've not become wedged. | |
722 | */ | |
723 | ||
724 | static unsigned short eexp_start_irq(struct net_device *dev, | |
725 | unsigned short status) | |
726 | { | |
727 | unsigned short ack_cmd = SCB_ack(status); | |
728 | struct net_local *lp = netdev_priv(dev); | |
729 | unsigned short ioaddr = dev->base_addr; | |
730 | if ((dev->flags & IFF_UP) && !(lp->started & STARTED_CU)) { | |
731 | short diag_status, tdr_status; | |
732 | while (SCB_CUstat(status)==2) | |
733 | status = scb_status(dev); | |
734 | #if NET_DEBUG > 4 | |
735 | printk("%s: CU went non-active (status %04x)\n", | |
736 | dev->name, status); | |
737 | #endif | |
738 | ||
739 | outw(CONF_DIAG_RESULT & ~31, ioaddr + SM_PTR); | |
740 | diag_status = inw(ioaddr + SHADOW(CONF_DIAG_RESULT)); | |
741 | if (diag_status & 1<<11) { | |
6aa20a22 | 742 | printk(KERN_WARNING "%s: 82586 failed self-test\n", |
1da177e4 LT |
743 | dev->name); |
744 | } else if (!(diag_status & 1<<13)) { | |
745 | printk(KERN_WARNING "%s: 82586 self-test failed to complete\n", dev->name); | |
746 | } | |
747 | ||
748 | outw(CONF_TDR_RESULT & ~31, ioaddr + SM_PTR); | |
749 | tdr_status = inw(ioaddr + SHADOW(CONF_TDR_RESULT)); | |
750 | if (tdr_status & (TDR_SHORT|TDR_OPEN)) { | |
751 | printk(KERN_WARNING "%s: TDR reports cable %s at %d tick%s\n", dev->name, (tdr_status & TDR_SHORT)?"short":"broken", tdr_status & TDR_TIME, ((tdr_status & TDR_TIME) != 1) ? "s" : ""); | |
6aa20a22 | 752 | } |
1da177e4 LT |
753 | else if (tdr_status & TDR_XCVRPROBLEM) { |
754 | printk(KERN_WARNING "%s: TDR reports transceiver problem\n", dev->name); | |
755 | } | |
756 | else if (tdr_status & TDR_LINKOK) { | |
757 | #if NET_DEBUG > 4 | |
758 | printk(KERN_DEBUG "%s: TDR reports link OK\n", dev->name); | |
759 | #endif | |
760 | } else { | |
761 | printk("%s: TDR is ga-ga (status %04x)\n", dev->name, | |
762 | tdr_status); | |
763 | } | |
6aa20a22 | 764 | |
1da177e4 LT |
765 | lp->started |= STARTED_CU; |
766 | scb_wrcbl(dev, lp->tx_link); | |
767 | /* if the RU isn't running, start it now */ | |
768 | if (!(lp->started & STARTED_RU)) { | |
769 | ack_cmd |= SCB_RUstart; | |
770 | scb_wrrfa(dev, lp->rx_buf_start); | |
771 | lp->rx_ptr = lp->rx_buf_start; | |
772 | lp->started |= STARTED_RU; | |
773 | } | |
774 | ack_cmd |= SCB_CUstart | 0x2000; | |
775 | } | |
776 | ||
6aa20a22 | 777 | if ((dev->flags & IFF_UP) && !(lp->started & STARTED_RU) && SCB_RUstat(status)==4) |
1da177e4 LT |
778 | lp->started|=STARTED_RU; |
779 | ||
780 | return ack_cmd; | |
781 | } | |
782 | ||
783 | static void eexp_cmd_clear(struct net_device *dev) | |
784 | { | |
785 | unsigned long int oldtime = jiffies; | |
786 | while (scb_rdcmd(dev) && ((jiffies-oldtime)<10)); | |
787 | if (scb_rdcmd(dev)) { | |
788 | printk("%s: command didn't clear\n", dev->name); | |
789 | } | |
790 | } | |
6aa20a22 | 791 | |
7d12e780 | 792 | static irqreturn_t eexp_irq(int irq, void *dev_info) |
1da177e4 LT |
793 | { |
794 | struct net_device *dev = dev_info; | |
795 | struct net_local *lp; | |
796 | unsigned short ioaddr,status,ack_cmd; | |
797 | unsigned short old_read_ptr, old_write_ptr; | |
798 | ||
1da177e4 LT |
799 | lp = netdev_priv(dev); |
800 | ioaddr = dev->base_addr; | |
801 | ||
802 | spin_lock(&lp->lock); | |
803 | ||
804 | old_read_ptr = inw(ioaddr+READ_PTR); | |
805 | old_write_ptr = inw(ioaddr+WRITE_PTR); | |
806 | ||
807 | outb(SIRQ_dis|irqrmap[irq],ioaddr+SET_IRQ); | |
808 | ||
6aa20a22 | 809 | |
1da177e4 LT |
810 | status = scb_status(dev); |
811 | ||
812 | #if NET_DEBUG > 4 | |
813 | printk(KERN_DEBUG "%s: interrupt (status %x)\n", dev->name, status); | |
814 | #endif | |
815 | ||
816 | if (lp->started == (STARTED_CU | STARTED_RU)) { | |
817 | ||
818 | do { | |
819 | eexp_cmd_clear(dev); | |
820 | ||
821 | ack_cmd = SCB_ack(status); | |
822 | scb_command(dev, ack_cmd); | |
823 | outb(0,ioaddr+SIGNAL_CA); | |
824 | ||
825 | eexp_cmd_clear(dev); | |
826 | ||
827 | if (SCB_complete(status)) { | |
828 | if (!eexp_hw_lasttxstat(dev)) { | |
829 | printk("%s: tx interrupt but no status\n", dev->name); | |
830 | } | |
831 | } | |
6aa20a22 JG |
832 | |
833 | if (SCB_rxdframe(status)) | |
1da177e4 LT |
834 | eexp_hw_rx_pio(dev); |
835 | ||
836 | status = scb_status(dev); | |
837 | } while (status & 0xc000); | |
838 | ||
6aa20a22 | 839 | if (SCB_RUdead(status)) |
1da177e4 LT |
840 | { |
841 | printk(KERN_WARNING "%s: RU stopped: status %04x\n", | |
842 | dev->name,status); | |
843 | #if 0 | |
844 | printk(KERN_WARNING "%s: cur_rfd=%04x, cur_rbd=%04x\n", dev->name, lp->cur_rfd, lp->cur_rbd); | |
845 | outw(lp->cur_rfd, ioaddr+READ_PTR); | |
846 | printk(KERN_WARNING "%s: [%04x]\n", dev->name, inw(ioaddr+DATAPORT)); | |
847 | outw(lp->cur_rfd+6, ioaddr+READ_PTR); | |
848 | printk(KERN_WARNING "%s: rbd is %04x\n", dev->name, rbd= inw(ioaddr+DATAPORT)); | |
849 | outw(rbd, ioaddr+READ_PTR); | |
850 | printk(KERN_WARNING "%s: [%04x %04x] ", dev->name, inw(ioaddr+DATAPORT), inw(ioaddr+DATAPORT)); | |
851 | outw(rbd+8, ioaddr+READ_PTR); | |
852 | printk("[%04x]\n", inw(ioaddr+DATAPORT)); | |
853 | #endif | |
854 | lp->stats.rx_errors++; | |
855 | #if 1 | |
856 | eexp_hw_rxinit(dev); | |
857 | #else | |
858 | lp->cur_rfd = lp->first_rfd; | |
859 | #endif | |
860 | scb_wrrfa(dev, lp->rx_buf_start); | |
861 | scb_command(dev, SCB_RUstart); | |
862 | outb(0,ioaddr+SIGNAL_CA); | |
6aa20a22 | 863 | } |
1da177e4 | 864 | } else { |
6aa20a22 | 865 | if (status & 0x8000) |
1da177e4 LT |
866 | ack_cmd = eexp_start_irq(dev, status); |
867 | else | |
868 | ack_cmd = SCB_ack(status); | |
869 | scb_command(dev, ack_cmd); | |
870 | outb(0,ioaddr+SIGNAL_CA); | |
871 | } | |
872 | ||
873 | eexp_cmd_clear(dev); | |
874 | ||
6aa20a22 | 875 | outb(SIRQ_en|irqrmap[irq],ioaddr+SET_IRQ); |
1da177e4 | 876 | |
6aa20a22 | 877 | #if NET_DEBUG > 6 |
1da177e4 LT |
878 | printk("%s: leaving eexp_irq()\n", dev->name); |
879 | #endif | |
880 | outw(old_read_ptr, ioaddr+READ_PTR); | |
881 | outw(old_write_ptr, ioaddr+WRITE_PTR); | |
6aa20a22 | 882 | |
1da177e4 LT |
883 | spin_unlock(&lp->lock); |
884 | return IRQ_HANDLED; | |
885 | } | |
886 | ||
887 | /* | |
888 | * Hardware access functions | |
889 | */ | |
890 | ||
891 | /* | |
892 | * Set the cable type to use. | |
893 | */ | |
894 | ||
895 | static void eexp_hw_set_interface(struct net_device *dev) | |
896 | { | |
897 | unsigned char oldval = inb(dev->base_addr + 0x300e); | |
898 | oldval &= ~0x82; | |
899 | switch (dev->if_port) { | |
900 | case TPE: | |
901 | oldval |= 0x2; | |
902 | case BNC: | |
903 | oldval |= 0x80; | |
904 | break; | |
905 | } | |
906 | outb(oldval, dev->base_addr+0x300e); | |
907 | mdelay(20); | |
908 | } | |
909 | ||
910 | /* | |
911 | * Check all the receive buffers, and hand any received packets | |
912 | * to the upper levels. Basic sanity check on each frame | |
913 | * descriptor, though we don't bother trying to fix broken ones. | |
914 | */ | |
915 | ||
916 | static void eexp_hw_rx_pio(struct net_device *dev) | |
917 | { | |
918 | struct net_local *lp = netdev_priv(dev); | |
919 | unsigned short rx_block = lp->rx_ptr; | |
920 | unsigned short boguscount = lp->num_rx_bufs; | |
921 | unsigned short ioaddr = dev->base_addr; | |
922 | unsigned short status; | |
923 | ||
924 | #if NET_DEBUG > 6 | |
925 | printk(KERN_DEBUG "%s: eexp_hw_rx()\n", dev->name); | |
926 | #endif | |
927 | ||
928 | do { | |
929 | unsigned short rfd_cmd, rx_next, pbuf, pkt_len; | |
6aa20a22 | 930 | |
1da177e4 LT |
931 | outw(rx_block, ioaddr + READ_PTR); |
932 | status = inw(ioaddr + DATAPORT); | |
933 | ||
934 | if (FD_Done(status)) | |
935 | { | |
936 | rfd_cmd = inw(ioaddr + DATAPORT); | |
937 | rx_next = inw(ioaddr + DATAPORT); | |
938 | pbuf = inw(ioaddr + DATAPORT); | |
6aa20a22 | 939 | |
1da177e4 LT |
940 | outw(pbuf, ioaddr + READ_PTR); |
941 | pkt_len = inw(ioaddr + DATAPORT); | |
942 | ||
943 | if (rfd_cmd!=0x0000) | |
944 | { | |
945 | printk(KERN_WARNING "%s: rfd_cmd not zero:0x%04x\n", | |
946 | dev->name, rfd_cmd); | |
947 | continue; | |
948 | } | |
949 | else if (pbuf!=rx_block+0x16) | |
950 | { | |
6aa20a22 | 951 | printk(KERN_WARNING "%s: rfd and rbd out of sync 0x%04x 0x%04x\n", |
1da177e4 LT |
952 | dev->name, rx_block+0x16, pbuf); |
953 | continue; | |
954 | } | |
6aa20a22 | 955 | else if ((pkt_len & 0xc000)!=0xc000) |
1da177e4 LT |
956 | { |
957 | printk(KERN_WARNING "%s: EOF or F not set on received buffer (%04x)\n", | |
958 | dev->name, pkt_len & 0xc000); | |
959 | continue; | |
960 | } | |
6aa20a22 | 961 | else if (!FD_OK(status)) |
1da177e4 LT |
962 | { |
963 | lp->stats.rx_errors++; | |
964 | if (FD_CRC(status)) | |
965 | lp->stats.rx_crc_errors++; | |
966 | if (FD_Align(status)) | |
967 | lp->stats.rx_frame_errors++; | |
968 | if (FD_Resrc(status)) | |
969 | lp->stats.rx_fifo_errors++; | |
970 | if (FD_DMA(status)) | |
971 | lp->stats.rx_over_errors++; | |
972 | if (FD_Short(status)) | |
973 | lp->stats.rx_length_errors++; | |
974 | } | |
975 | else | |
976 | { | |
977 | struct sk_buff *skb; | |
978 | pkt_len &= 0x3fff; | |
979 | skb = dev_alloc_skb(pkt_len+16); | |
980 | if (skb == NULL) | |
981 | { | |
982 | printk(KERN_WARNING "%s: Memory squeeze, dropping packet\n",dev->name); | |
983 | lp->stats.rx_dropped++; | |
984 | break; | |
985 | } | |
986 | skb->dev = dev; | |
987 | skb_reserve(skb, 2); | |
988 | outw(pbuf+10, ioaddr+READ_PTR); | |
989 | insw(ioaddr+DATAPORT, skb_put(skb,pkt_len),(pkt_len+1)>>1); | |
990 | skb->protocol = eth_type_trans(skb,dev); | |
991 | netif_rx(skb); | |
992 | dev->last_rx = jiffies; | |
993 | lp->stats.rx_packets++; | |
994 | lp->stats.rx_bytes += pkt_len; | |
995 | } | |
996 | outw(rx_block, ioaddr+WRITE_PTR); | |
997 | outw(0, ioaddr+DATAPORT); | |
998 | outw(0, ioaddr+DATAPORT); | |
999 | rx_block = rx_next; | |
1000 | } | |
1001 | } while (FD_Done(status) && boguscount--); | |
1002 | lp->rx_ptr = rx_block; | |
1003 | } | |
1004 | ||
1005 | /* | |
1006 | * Hand a packet to the card for transmission | |
1007 | * If we get here, we MUST have already checked | |
1008 | * to make sure there is room in the transmit | |
1009 | * buffer region. | |
1010 | */ | |
1011 | ||
1012 | static void eexp_hw_tx_pio(struct net_device *dev, unsigned short *buf, | |
1013 | unsigned short len) | |
1014 | { | |
1015 | struct net_local *lp = netdev_priv(dev); | |
1016 | unsigned short ioaddr = dev->base_addr; | |
1017 | ||
1018 | if (LOCKUP16 || lp->width) { | |
1019 | /* Stop the CU so that there is no chance that it | |
1020 | jumps off to a bogus address while we are writing the | |
6aa20a22 | 1021 | pointer to the next transmit packet in 8-bit mode -- |
1da177e4 | 1022 | this eliminates the "CU wedged" errors in 8-bit mode. |
6aa20a22 | 1023 | (Zoltan Szilagyi 10-12-96) */ |
1da177e4 LT |
1024 | scb_command(dev, SCB_CUsuspend); |
1025 | outw(0xFFFF, ioaddr+SIGNAL_CA); | |
1026 | } | |
1027 | ||
1028 | outw(lp->tx_head, ioaddr + WRITE_PTR); | |
1029 | ||
1030 | outw(0x0000, ioaddr + DATAPORT); | |
1031 | outw(Cmd_INT|Cmd_Xmit, ioaddr + DATAPORT); | |
1032 | outw(lp->tx_head+0x08, ioaddr + DATAPORT); | |
1033 | outw(lp->tx_head+0x0e, ioaddr + DATAPORT); | |
1034 | ||
1035 | outw(0x0000, ioaddr + DATAPORT); | |
1036 | outw(0x0000, ioaddr + DATAPORT); | |
1037 | outw(lp->tx_head+0x08, ioaddr + DATAPORT); | |
1038 | ||
1039 | outw(0x8000|len, ioaddr + DATAPORT); | |
1040 | outw(-1, ioaddr + DATAPORT); | |
1041 | outw(lp->tx_head+0x16, ioaddr + DATAPORT); | |
1042 | outw(0, ioaddr + DATAPORT); | |
1043 | ||
1044 | outsw(ioaddr + DATAPORT, buf, (len+1)>>1); | |
1045 | ||
1046 | outw(lp->tx_tail+0xc, ioaddr + WRITE_PTR); | |
1047 | outw(lp->tx_head, ioaddr + DATAPORT); | |
1048 | ||
1049 | dev->trans_start = jiffies; | |
1050 | lp->tx_tail = lp->tx_head; | |
1051 | if (lp->tx_head==TX_BUF_START+((lp->num_tx_bufs-1)*TX_BUF_SIZE)) | |
1052 | lp->tx_head = TX_BUF_START; | |
1053 | else | |
1054 | lp->tx_head += TX_BUF_SIZE; | |
1055 | if (lp->tx_head != lp->tx_reap) | |
1056 | netif_wake_queue(dev); | |
6aa20a22 | 1057 | |
1da177e4 LT |
1058 | if (LOCKUP16 || lp->width) { |
1059 | /* Restart the CU so that the packet can actually | |
1060 | be transmitted. (Zoltan Szilagyi 10-12-96) */ | |
1061 | scb_command(dev, SCB_CUresume); | |
1062 | outw(0xFFFF, ioaddr+SIGNAL_CA); | |
1063 | } | |
1064 | ||
1065 | lp->stats.tx_packets++; | |
1066 | lp->last_tx = jiffies; | |
1067 | } | |
1068 | ||
1069 | /* | |
1070 | * Sanity check the suspected EtherExpress card | |
1071 | * Read hardware address, reset card, size memory and initialize buffer | |
1072 | * memory pointers. These are held in dev->priv, in case someone has more | |
1073 | * than one card in a machine. | |
1074 | */ | |
1075 | ||
1076 | static int __init eexp_hw_probe(struct net_device *dev, unsigned short ioaddr) | |
1077 | { | |
1078 | unsigned short hw_addr[3]; | |
1079 | unsigned char buswidth; | |
1080 | unsigned int memory_size; | |
1081 | int i; | |
1082 | unsigned short xsum = 0; | |
1083 | struct net_local *lp = netdev_priv(dev); | |
1084 | ||
1085 | printk("%s: EtherExpress 16 at %#x ",dev->name,ioaddr); | |
1086 | ||
1087 | outb(ASIC_RST, ioaddr+EEPROM_Ctrl); | |
1088 | outb(0, ioaddr+EEPROM_Ctrl); | |
1089 | udelay(500); | |
1090 | outb(i586_RST, ioaddr+EEPROM_Ctrl); | |
1091 | ||
1092 | hw_addr[0] = eexp_hw_readeeprom(ioaddr,2); | |
1093 | hw_addr[1] = eexp_hw_readeeprom(ioaddr,3); | |
1094 | hw_addr[2] = eexp_hw_readeeprom(ioaddr,4); | |
1095 | ||
1096 | /* Standard Address or Compaq LTE Address */ | |
1097 | if (!((hw_addr[2]==0x00aa && ((hw_addr[1] & 0xff00)==0x0000)) || | |
6aa20a22 | 1098 | (hw_addr[2]==0x0080 && ((hw_addr[1] & 0xff00)==0x5F00)))) |
1da177e4 LT |
1099 | { |
1100 | printk(" rejected: invalid address %04x%04x%04x\n", | |
1101 | hw_addr[2],hw_addr[1],hw_addr[0]); | |
1102 | return -ENODEV; | |
1103 | } | |
1104 | ||
1105 | /* Calculate the EEPROM checksum. Carry on anyway if it's bad, | |
1106 | * though. | |
1107 | */ | |
1108 | for (i = 0; i < 64; i++) | |
1109 | xsum += eexp_hw_readeeprom(ioaddr, i); | |
1110 | if (xsum != 0xbaba) | |
1111 | printk(" (bad EEPROM xsum 0x%02x)", xsum); | |
1112 | ||
1113 | dev->base_addr = ioaddr; | |
1114 | for ( i=0 ; i<6 ; i++ ) | |
1115 | dev->dev_addr[i] = ((unsigned char *)hw_addr)[5-i]; | |
1116 | ||
1117 | { | |
1118 | static char irqmap[]={0, 9, 3, 4, 5, 10, 11, 0}; | |
1119 | unsigned short setupval = eexp_hw_readeeprom(ioaddr,0); | |
1120 | ||
1121 | /* Use the IRQ from EEPROM if none was given */ | |
1122 | if (!dev->irq) | |
1123 | dev->irq = irqmap[setupval>>13]; | |
1124 | ||
1125 | if (dev->if_port == 0xff) { | |
1126 | dev->if_port = !(setupval & 0x1000) ? AUI : | |
1127 | eexp_hw_readeeprom(ioaddr,5) & 0x1 ? TPE : BNC; | |
1128 | } | |
1129 | ||
1130 | buswidth = !((setupval & 0x400) >> 10); | |
1131 | } | |
1132 | ||
1133 | memset(lp, 0, sizeof(struct net_local)); | |
1134 | spin_lock_init(&lp->lock); | |
1135 | ||
6aa20a22 | 1136 | printk("(IRQ %d, %s connector, %d-bit bus", dev->irq, |
1da177e4 | 1137 | eexp_ifmap[dev->if_port], buswidth?8:16); |
6aa20a22 | 1138 | |
1da177e4 LT |
1139 | if (!request_region(dev->base_addr + 0x300e, 1, "EtherExpress")) |
1140 | return -EBUSY; | |
1141 | ||
1142 | eexp_hw_set_interface(dev); | |
6aa20a22 | 1143 | |
1da177e4 | 1144 | release_region(dev->base_addr + 0x300e, 1); |
6aa20a22 | 1145 | |
1da177e4 LT |
1146 | /* Find out how much RAM we have on the card */ |
1147 | outw(0, dev->base_addr + WRITE_PTR); | |
1148 | for (i = 0; i < 32768; i++) | |
1149 | outw(0, dev->base_addr + DATAPORT); | |
1150 | ||
1151 | for (memory_size = 0; memory_size < 64; memory_size++) | |
1152 | { | |
1153 | outw(memory_size<<10, dev->base_addr + READ_PTR); | |
1154 | if (inw(dev->base_addr+DATAPORT)) | |
1155 | break; | |
1156 | outw(memory_size<<10, dev->base_addr + WRITE_PTR); | |
1157 | outw(memory_size | 0x5000, dev->base_addr+DATAPORT); | |
1158 | outw(memory_size<<10, dev->base_addr + READ_PTR); | |
1159 | if (inw(dev->base_addr+DATAPORT) != (memory_size | 0x5000)) | |
1160 | break; | |
1161 | } | |
1162 | ||
1163 | /* Sort out the number of buffers. We may have 16, 32, 48 or 64k | |
1164 | * of RAM to play with. | |
1165 | */ | |
1166 | lp->num_tx_bufs = 4; | |
1167 | lp->rx_buf_end = 0x3ff6; | |
1168 | switch (memory_size) | |
1169 | { | |
1170 | case 64: | |
1171 | lp->rx_buf_end += 0x4000; | |
1172 | case 48: | |
1173 | lp->num_tx_bufs += 4; | |
1174 | lp->rx_buf_end += 0x4000; | |
1175 | case 32: | |
1176 | lp->rx_buf_end += 0x4000; | |
1177 | case 16: | |
1178 | printk(", %dk RAM)\n", memory_size); | |
1179 | break; | |
1180 | default: | |
1181 | printk(") bad memory size (%dk).\n", memory_size); | |
1182 | return -ENODEV; | |
1183 | break; | |
1184 | } | |
1185 | ||
1186 | lp->rx_buf_start = TX_BUF_START + (lp->num_tx_bufs*TX_BUF_SIZE); | |
1187 | lp->width = buswidth; | |
1188 | ||
1189 | dev->open = eexp_open; | |
1190 | dev->stop = eexp_close; | |
1191 | dev->hard_start_xmit = eexp_xmit; | |
1192 | dev->get_stats = eexp_stats; | |
1193 | dev->set_multicast_list = &eexp_set_multicast; | |
1194 | dev->tx_timeout = eexp_timeout; | |
1195 | dev->watchdog_timeo = 2*HZ; | |
b1fc5505 | 1196 | |
1197 | return register_netdev(dev); | |
1da177e4 LT |
1198 | } |
1199 | ||
1200 | /* | |
1201 | * Read a word from the EtherExpress on-board serial EEPROM. | |
1202 | * The EEPROM contains 64 words of 16 bits. | |
1203 | */ | |
1204 | static unsigned short __init eexp_hw_readeeprom(unsigned short ioaddr, | |
1205 | unsigned char location) | |
1206 | { | |
1207 | unsigned short cmd = 0x180|(location&0x7f); | |
1208 | unsigned short rval = 0,wval = EC_CS|i586_RST; | |
1209 | int i; | |
1210 | ||
1211 | outb(EC_CS|i586_RST,ioaddr+EEPROM_Ctrl); | |
1212 | for (i=0x100 ; i ; i>>=1 ) | |
1213 | { | |
1214 | if (cmd&i) | |
1215 | wval |= EC_Wr; | |
1216 | else | |
1217 | wval &= ~EC_Wr; | |
1218 | ||
1219 | outb(wval,ioaddr+EEPROM_Ctrl); | |
1220 | outb(wval|EC_Clk,ioaddr+EEPROM_Ctrl); | |
1221 | eeprom_delay(); | |
1222 | outb(wval,ioaddr+EEPROM_Ctrl); | |
1223 | eeprom_delay(); | |
1224 | } | |
1225 | wval &= ~EC_Wr; | |
1226 | outb(wval,ioaddr+EEPROM_Ctrl); | |
1227 | for (i=0x8000 ; i ; i>>=1 ) | |
1228 | { | |
1229 | outb(wval|EC_Clk,ioaddr+EEPROM_Ctrl); | |
1230 | eeprom_delay(); | |
1231 | if (inb(ioaddr+EEPROM_Ctrl)&EC_Rd) | |
1232 | rval |= i; | |
1233 | outb(wval,ioaddr+EEPROM_Ctrl); | |
1234 | eeprom_delay(); | |
1235 | } | |
1236 | wval &= ~EC_CS; | |
1237 | outb(wval|EC_Clk,ioaddr+EEPROM_Ctrl); | |
1238 | eeprom_delay(); | |
1239 | outb(wval,ioaddr+EEPROM_Ctrl); | |
1240 | eeprom_delay(); | |
1241 | return rval; | |
1242 | } | |
1243 | ||
1244 | /* | |
1245 | * Reap tx buffers and return last transmit status. | |
1246 | * if ==0 then either: | |
1247 | * a) we're not transmitting anything, so why are we here? | |
1248 | * b) we've died. | |
1249 | * otherwise, Stat_Busy(return) means we've still got some packets | |
1250 | * to transmit, Stat_Done(return) means our buffers should be empty | |
1251 | * again | |
1252 | */ | |
1253 | ||
1254 | static unsigned short eexp_hw_lasttxstat(struct net_device *dev) | |
1255 | { | |
1256 | struct net_local *lp = netdev_priv(dev); | |
1257 | unsigned short tx_block = lp->tx_reap; | |
1258 | unsigned short status; | |
1259 | ||
1260 | if (!netif_queue_stopped(dev) && lp->tx_head==lp->tx_reap) | |
1261 | return 0x0000; | |
1262 | ||
1263 | do | |
1264 | { | |
1265 | outw(tx_block & ~31, dev->base_addr + SM_PTR); | |
1266 | status = inw(dev->base_addr + SHADOW(tx_block)); | |
1267 | if (!Stat_Done(status)) | |
1268 | { | |
1269 | lp->tx_link = tx_block; | |
1270 | return status; | |
1271 | } | |
1272 | else | |
1273 | { | |
1274 | lp->last_tx_restart = 0; | |
1275 | lp->stats.collisions += Stat_NoColl(status); | |
1276 | if (!Stat_OK(status)) | |
1277 | { | |
1278 | char *whatsup = NULL; | |
1279 | lp->stats.tx_errors++; | |
6aa20a22 | 1280 | if (Stat_Abort(status)) |
1da177e4 LT |
1281 | lp->stats.tx_aborted_errors++; |
1282 | if (Stat_TNoCar(status)) { | |
1283 | whatsup = "aborted, no carrier"; | |
1284 | lp->stats.tx_carrier_errors++; | |
1285 | } | |
1286 | if (Stat_TNoCTS(status)) { | |
1287 | whatsup = "aborted, lost CTS"; | |
1288 | lp->stats.tx_carrier_errors++; | |
1289 | } | |
1290 | if (Stat_TNoDMA(status)) { | |
1291 | whatsup = "FIFO underran"; | |
1292 | lp->stats.tx_fifo_errors++; | |
1293 | } | |
1294 | if (Stat_TXColl(status)) { | |
1295 | whatsup = "aborted, too many collisions"; | |
1296 | lp->stats.tx_aborted_errors++; | |
1297 | } | |
1298 | if (whatsup) | |
1299 | printk(KERN_INFO "%s: transmit %s\n", | |
1300 | dev->name, whatsup); | |
1301 | } | |
1302 | else | |
1303 | lp->stats.tx_packets++; | |
1304 | } | |
1305 | if (tx_block == TX_BUF_START+((lp->num_tx_bufs-1)*TX_BUF_SIZE)) | |
1306 | lp->tx_reap = tx_block = TX_BUF_START; | |
1307 | else | |
1308 | lp->tx_reap = tx_block += TX_BUF_SIZE; | |
1309 | netif_wake_queue(dev); | |
1310 | } | |
1311 | while (lp->tx_reap != lp->tx_head); | |
1312 | ||
1313 | lp->tx_link = lp->tx_tail + 0x08; | |
1314 | ||
1315 | return status; | |
1316 | } | |
1317 | ||
1318 | /* | |
1319 | * This should never happen. It is called when some higher routine detects | |
1320 | * that the CU has stopped, to try to restart it from the last packet we knew | |
1321 | * we were working on, or the idle loop if we had finished for the time. | |
1322 | */ | |
1323 | ||
1324 | static void eexp_hw_txrestart(struct net_device *dev) | |
1325 | { | |
1326 | struct net_local *lp = netdev_priv(dev); | |
1327 | unsigned short ioaddr = dev->base_addr; | |
1328 | ||
1329 | lp->last_tx_restart = lp->tx_link; | |
1330 | scb_wrcbl(dev, lp->tx_link); | |
1331 | scb_command(dev, SCB_CUstart); | |
1332 | outb(0,ioaddr+SIGNAL_CA); | |
1333 | ||
1334 | { | |
1335 | unsigned short boguscount=50,failcount=5; | |
1336 | while (!scb_status(dev)) | |
1337 | { | |
1338 | if (!--boguscount) | |
1339 | { | |
1340 | if (--failcount) | |
1341 | { | |
1342 | printk(KERN_WARNING "%s: CU start timed out, status %04x, cmd %04x\n", dev->name, scb_status(dev), scb_rdcmd(dev)); | |
1343 | scb_wrcbl(dev, lp->tx_link); | |
1344 | scb_command(dev, SCB_CUstart); | |
1345 | outb(0,ioaddr+SIGNAL_CA); | |
1346 | boguscount = 100; | |
1347 | } | |
1348 | else | |
1349 | { | |
1350 | printk(KERN_WARNING "%s: Failed to restart CU, resetting board...\n",dev->name); | |
1351 | eexp_hw_init586(dev); | |
1352 | netif_wake_queue(dev); | |
1353 | return; | |
1354 | } | |
1355 | } | |
1356 | } | |
1357 | } | |
1358 | } | |
1359 | ||
1360 | /* | |
1361 | * Writes down the list of transmit buffers into card memory. Each | |
1362 | * entry consists of an 82586 transmit command, followed by a jump | |
1363 | * pointing to itself. When we want to transmit a packet, we write | |
1364 | * the data into the appropriate transmit buffer and then modify the | |
1365 | * preceding jump to point at the new transmit command. This means that | |
1366 | * the 586 command unit is continuously active. | |
1367 | */ | |
1368 | ||
1369 | static void eexp_hw_txinit(struct net_device *dev) | |
1370 | { | |
1371 | struct net_local *lp = netdev_priv(dev); | |
1372 | unsigned short tx_block = TX_BUF_START; | |
1373 | unsigned short curtbuf; | |
1374 | unsigned short ioaddr = dev->base_addr; | |
1375 | ||
1376 | for ( curtbuf=0 ; curtbuf<lp->num_tx_bufs ; curtbuf++ ) | |
1377 | { | |
1378 | outw(tx_block, ioaddr + WRITE_PTR); | |
1379 | ||
1380 | outw(0x0000, ioaddr + DATAPORT); | |
1381 | outw(Cmd_INT|Cmd_Xmit, ioaddr + DATAPORT); | |
1382 | outw(tx_block+0x08, ioaddr + DATAPORT); | |
1383 | outw(tx_block+0x0e, ioaddr + DATAPORT); | |
1384 | ||
1385 | outw(0x0000, ioaddr + DATAPORT); | |
1386 | outw(0x0000, ioaddr + DATAPORT); | |
1387 | outw(tx_block+0x08, ioaddr + DATAPORT); | |
1388 | ||
1389 | outw(0x8000, ioaddr + DATAPORT); | |
1390 | outw(-1, ioaddr + DATAPORT); | |
1391 | outw(tx_block+0x16, ioaddr + DATAPORT); | |
1392 | outw(0x0000, ioaddr + DATAPORT); | |
1393 | ||
1394 | tx_block += TX_BUF_SIZE; | |
1395 | } | |
1396 | lp->tx_head = TX_BUF_START; | |
1397 | lp->tx_reap = TX_BUF_START; | |
1398 | lp->tx_tail = tx_block - TX_BUF_SIZE; | |
1399 | lp->tx_link = lp->tx_tail + 0x08; | |
1400 | lp->rx_buf_start = tx_block; | |
1401 | ||
1402 | } | |
1403 | ||
1404 | /* | |
1405 | * Write the circular list of receive buffer descriptors to card memory. | |
1406 | * The end of the list isn't marked, which means that the 82586 receive | |
1407 | * unit will loop until buffers become available (this avoids it giving us | |
1408 | * "out of resources" messages). | |
1409 | */ | |
1410 | ||
1411 | static void eexp_hw_rxinit(struct net_device *dev) | |
1412 | { | |
1413 | struct net_local *lp = netdev_priv(dev); | |
1414 | unsigned short rx_block = lp->rx_buf_start; | |
1415 | unsigned short ioaddr = dev->base_addr; | |
1416 | ||
1417 | lp->num_rx_bufs = 0; | |
1418 | lp->rx_first = lp->rx_ptr = rx_block; | |
1419 | do | |
1420 | { | |
1421 | lp->num_rx_bufs++; | |
1422 | ||
1423 | outw(rx_block, ioaddr + WRITE_PTR); | |
1424 | ||
1425 | outw(0, ioaddr + DATAPORT); outw(0, ioaddr+DATAPORT); | |
1426 | outw(rx_block + RX_BUF_SIZE, ioaddr+DATAPORT); | |
1427 | outw(0xffff, ioaddr+DATAPORT); | |
1428 | ||
1429 | outw(0x0000, ioaddr+DATAPORT); | |
1430 | outw(0xdead, ioaddr+DATAPORT); | |
1431 | outw(0xdead, ioaddr+DATAPORT); | |
1432 | outw(0xdead, ioaddr+DATAPORT); | |
1433 | outw(0xdead, ioaddr+DATAPORT); | |
1434 | outw(0xdead, ioaddr+DATAPORT); | |
1435 | outw(0xdead, ioaddr+DATAPORT); | |
1436 | ||
1437 | outw(0x0000, ioaddr+DATAPORT); | |
1438 | outw(rx_block + RX_BUF_SIZE + 0x16, ioaddr+DATAPORT); | |
1439 | outw(rx_block + 0x20, ioaddr+DATAPORT); | |
1440 | outw(0, ioaddr+DATAPORT); | |
1441 | outw(RX_BUF_SIZE-0x20, ioaddr+DATAPORT); | |
1442 | ||
1443 | lp->rx_last = rx_block; | |
1444 | rx_block += RX_BUF_SIZE; | |
1445 | } while (rx_block <= lp->rx_buf_end-RX_BUF_SIZE); | |
1446 | ||
1447 | ||
1448 | /* Make first Rx frame descriptor point to first Rx buffer | |
1449 | descriptor */ | |
1450 | outw(lp->rx_first + 6, ioaddr+WRITE_PTR); | |
1451 | outw(lp->rx_first + 0x16, ioaddr+DATAPORT); | |
1452 | ||
1453 | /* Close Rx frame descriptor ring */ | |
1454 | outw(lp->rx_last + 4, ioaddr+WRITE_PTR); | |
1455 | outw(lp->rx_first, ioaddr+DATAPORT); | |
6aa20a22 | 1456 | |
1da177e4 LT |
1457 | /* Close Rx buffer descriptor ring */ |
1458 | outw(lp->rx_last + 0x16 + 2, ioaddr+WRITE_PTR); | |
1459 | outw(lp->rx_first + 0x16, ioaddr+DATAPORT); | |
6aa20a22 | 1460 | |
1da177e4 LT |
1461 | } |
1462 | ||
1463 | /* | |
1464 | * Un-reset the 586, and start the configuration sequence. We don't wait for | |
1465 | * this to finish, but allow the interrupt handler to start the CU and RU for | |
1466 | * us. We can't start the receive/transmission system up before we know that | |
1467 | * the hardware is configured correctly. | |
1468 | */ | |
1469 | ||
1470 | static void eexp_hw_init586(struct net_device *dev) | |
1471 | { | |
1472 | struct net_local *lp = netdev_priv(dev); | |
1473 | unsigned short ioaddr = dev->base_addr; | |
1474 | int i; | |
1475 | ||
1476 | #if NET_DEBUG > 6 | |
1477 | printk("%s: eexp_hw_init586()\n", dev->name); | |
1478 | #endif | |
1479 | ||
1480 | lp->started = 0; | |
1481 | ||
1482 | set_loopback(dev); | |
1483 | ||
1484 | outb(SIRQ_dis|irqrmap[dev->irq],ioaddr+SET_IRQ); | |
1485 | ||
1486 | /* Download the startup code */ | |
1487 | outw(lp->rx_buf_end & ~31, ioaddr + SM_PTR); | |
1488 | outw(lp->width?0x0001:0x0000, ioaddr + 0x8006); | |
1489 | outw(0x0000, ioaddr + 0x8008); | |
1490 | outw(0x0000, ioaddr + 0x800a); | |
1491 | outw(0x0000, ioaddr + 0x800c); | |
1492 | outw(0x0000, ioaddr + 0x800e); | |
1493 | ||
1494 | for (i = 0; i < (sizeof(start_code)); i+=32) { | |
1495 | int j; | |
1496 | outw(i, ioaddr + SM_PTR); | |
1497 | for (j = 0; j < 16; j+=2) | |
1498 | outw(start_code[(i+j)/2], | |
1499 | ioaddr+0x4000+j); | |
1500 | for (j = 0; j < 16; j+=2) | |
1501 | outw(start_code[(i+j+16)/2], | |
1502 | ioaddr+0x8000+j); | |
1503 | } | |
1504 | ||
1505 | /* Do we want promiscuous mode or multicast? */ | |
1506 | outw(CONF_PROMISC & ~31, ioaddr+SM_PTR); | |
1507 | i = inw(ioaddr+SHADOW(CONF_PROMISC)); | |
6aa20a22 | 1508 | outw((dev->flags & IFF_PROMISC)?(i|1):(i & ~1), |
1da177e4 LT |
1509 | ioaddr+SHADOW(CONF_PROMISC)); |
1510 | lp->was_promisc = dev->flags & IFF_PROMISC; | |
1511 | #if 0 | |
1512 | eexp_setup_filter(dev); | |
1513 | #endif | |
1514 | ||
1515 | /* Write our hardware address */ | |
1516 | outw(CONF_HWADDR & ~31, ioaddr+SM_PTR); | |
1517 | outw(((unsigned short *)dev->dev_addr)[0], ioaddr+SHADOW(CONF_HWADDR)); | |
6aa20a22 | 1518 | outw(((unsigned short *)dev->dev_addr)[1], |
1da177e4 LT |
1519 | ioaddr+SHADOW(CONF_HWADDR+2)); |
1520 | outw(((unsigned short *)dev->dev_addr)[2], | |
1521 | ioaddr+SHADOW(CONF_HWADDR+4)); | |
1522 | ||
1523 | eexp_hw_txinit(dev); | |
1524 | eexp_hw_rxinit(dev); | |
1525 | ||
1526 | outb(0,ioaddr+EEPROM_Ctrl); | |
1527 | mdelay(5); | |
1528 | ||
1529 | scb_command(dev, 0xf000); | |
1530 | outb(0,ioaddr+SIGNAL_CA); | |
1531 | ||
1532 | outw(0, ioaddr+SM_PTR); | |
1533 | ||
1534 | { | |
1535 | unsigned short rboguscount=50,rfailcount=5; | |
1536 | while (inw(ioaddr+0x4000)) | |
1537 | { | |
1538 | if (!--rboguscount) | |
1539 | { | |
1540 | printk(KERN_WARNING "%s: i82586 reset timed out, kicking...\n", | |
1541 | dev->name); | |
1542 | scb_command(dev, 0); | |
1543 | outb(0,ioaddr+SIGNAL_CA); | |
1544 | rboguscount = 100; | |
1545 | if (!--rfailcount) | |
1546 | { | |
1547 | printk(KERN_WARNING "%s: i82586 not responding, giving up.\n", | |
1548 | dev->name); | |
1549 | return; | |
1550 | } | |
1551 | } | |
1552 | } | |
1553 | } | |
1554 | ||
1555 | scb_wrcbl(dev, CONF_LINK); | |
1556 | scb_command(dev, 0xf000|SCB_CUstart); | |
1557 | outb(0,ioaddr+SIGNAL_CA); | |
1558 | ||
1559 | { | |
1560 | unsigned short iboguscount=50,ifailcount=5; | |
1561 | while (!scb_status(dev)) | |
1562 | { | |
1563 | if (!--iboguscount) | |
1564 | { | |
1565 | if (--ifailcount) | |
1566 | { | |
1567 | printk(KERN_WARNING "%s: i82586 initialization timed out, status %04x, cmd %04x\n", | |
1568 | dev->name, scb_status(dev), scb_rdcmd(dev)); | |
1569 | scb_wrcbl(dev, CONF_LINK); | |
1570 | scb_command(dev, 0xf000|SCB_CUstart); | |
1571 | outb(0,ioaddr+SIGNAL_CA); | |
1572 | iboguscount = 100; | |
1573 | } | |
1574 | else | |
1575 | { | |
1576 | printk(KERN_WARNING "%s: Failed to initialize i82586, giving up.\n",dev->name); | |
1577 | return; | |
1578 | } | |
1579 | } | |
1580 | } | |
1581 | } | |
1582 | ||
1583 | clear_loopback(dev); | |
1584 | outb(SIRQ_en|irqrmap[dev->irq],ioaddr+SET_IRQ); | |
1585 | ||
1586 | lp->init_time = jiffies; | |
1587 | #if NET_DEBUG > 6 | |
1588 | printk("%s: leaving eexp_hw_init586()\n", dev->name); | |
1589 | #endif | |
1590 | return; | |
1591 | } | |
1592 | ||
1593 | static void eexp_setup_filter(struct net_device *dev) | |
1594 | { | |
1595 | struct dev_mc_list *dmi = dev->mc_list; | |
1596 | unsigned short ioaddr = dev->base_addr; | |
1597 | int count = dev->mc_count; | |
1598 | int i; | |
1599 | if (count > 8) { | |
1600 | printk(KERN_INFO "%s: too many multicast addresses (%d)\n", | |
1601 | dev->name, count); | |
1602 | count = 8; | |
1603 | } | |
6aa20a22 | 1604 | |
1da177e4 LT |
1605 | outw(CONF_NR_MULTICAST & ~31, ioaddr+SM_PTR); |
1606 | outw(count, ioaddr+SHADOW(CONF_NR_MULTICAST)); | |
1607 | for (i = 0; i < count; i++) { | |
1608 | unsigned short *data = (unsigned short *)dmi->dmi_addr; | |
1609 | if (!dmi) { | |
1610 | printk(KERN_INFO "%s: too few multicast addresses\n", dev->name); | |
1611 | break; | |
1612 | } | |
1613 | if (dmi->dmi_addrlen != ETH_ALEN) { | |
1614 | printk(KERN_INFO "%s: invalid multicast address length given.\n", dev->name); | |
1615 | continue; | |
1616 | } | |
1617 | outw((CONF_MULTICAST+(6*i)) & ~31, ioaddr+SM_PTR); | |
1618 | outw(data[0], ioaddr+SHADOW(CONF_MULTICAST+(6*i))); | |
1619 | outw((CONF_MULTICAST+(6*i)+2) & ~31, ioaddr+SM_PTR); | |
1620 | outw(data[1], ioaddr+SHADOW(CONF_MULTICAST+(6*i)+2)); | |
1621 | outw((CONF_MULTICAST+(6*i)+4) & ~31, ioaddr+SM_PTR); | |
1622 | outw(data[2], ioaddr+SHADOW(CONF_MULTICAST+(6*i)+4)); | |
1623 | } | |
1624 | } | |
1625 | ||
1626 | /* | |
1627 | * Set or clear the multicast filter for this adaptor. | |
1628 | */ | |
1629 | static void | |
1630 | eexp_set_multicast(struct net_device *dev) | |
1631 | { | |
1632 | unsigned short ioaddr = dev->base_addr; | |
1633 | struct net_local *lp = netdev_priv(dev); | |
1634 | int kick = 0, i; | |
1635 | if ((dev->flags & IFF_PROMISC) != lp->was_promisc) { | |
1636 | outw(CONF_PROMISC & ~31, ioaddr+SM_PTR); | |
1637 | i = inw(ioaddr+SHADOW(CONF_PROMISC)); | |
1638 | outw((dev->flags & IFF_PROMISC)?(i|1):(i & ~1), | |
1639 | ioaddr+SHADOW(CONF_PROMISC)); | |
1640 | lp->was_promisc = dev->flags & IFF_PROMISC; | |
1641 | kick = 1; | |
1642 | } | |
1643 | if (!(dev->flags & IFF_PROMISC)) { | |
1644 | eexp_setup_filter(dev); | |
1645 | if (lp->old_mc_count != dev->mc_count) { | |
1646 | kick = 1; | |
1647 | lp->old_mc_count = dev->mc_count; | |
1648 | } | |
1649 | } | |
1650 | if (kick) { | |
1651 | unsigned long oj; | |
1652 | scb_command(dev, SCB_CUsuspend); | |
1653 | outb(0, ioaddr+SIGNAL_CA); | |
1654 | outb(0, ioaddr+SIGNAL_CA); | |
1655 | #if 0 | |
1656 | printk("%s: waiting for CU to go suspended\n", dev->name); | |
1657 | #endif | |
1658 | oj = jiffies; | |
1659 | while ((SCB_CUstat(scb_status(dev)) == 2) && | |
1660 | ((jiffies-oj) < 2000)); | |
1661 | if (SCB_CUstat(scb_status(dev)) == 2) | |
1662 | printk("%s: warning, CU didn't stop\n", dev->name); | |
1663 | lp->started &= ~(STARTED_CU); | |
1664 | scb_wrcbl(dev, CONF_LINK); | |
1665 | scb_command(dev, SCB_CUstart); | |
1666 | outb(0, ioaddr+SIGNAL_CA); | |
1667 | } | |
1668 | } | |
1669 | ||
1670 | ||
1671 | /* | |
1672 | * MODULE stuff | |
1673 | */ | |
1674 | ||
1675 | #ifdef MODULE | |
1676 | ||
1677 | #define EEXP_MAX_CARDS 4 /* max number of cards to support */ | |
1678 | ||
1679 | static struct net_device *dev_eexp[EEXP_MAX_CARDS]; | |
1680 | static int irq[EEXP_MAX_CARDS]; | |
1681 | static int io[EEXP_MAX_CARDS]; | |
1682 | ||
1683 | module_param_array(io, int, NULL, 0); | |
1684 | module_param_array(irq, int, NULL, 0); | |
1685 | MODULE_PARM_DESC(io, "EtherExpress 16 I/O base address(es)"); | |
1686 | MODULE_PARM_DESC(irq, "EtherExpress 16 IRQ number(s)"); | |
1687 | MODULE_LICENSE("GPL"); | |
1688 | ||
1689 | ||
1690 | /* Ideally the user would give us io=, irq= for every card. If any parameters | |
1691 | * are specified, we verify and then use them. If no parameters are given, we | |
1692 | * autoprobe for one card only. | |
1693 | */ | |
b1176b95 | 1694 | int __init init_module(void) |
1da177e4 LT |
1695 | { |
1696 | struct net_device *dev; | |
1697 | int this_dev, found = 0; | |
1698 | ||
1699 | for (this_dev = 0; this_dev < EEXP_MAX_CARDS; this_dev++) { | |
1700 | dev = alloc_etherdev(sizeof(struct net_local)); | |
1701 | dev->irq = irq[this_dev]; | |
1702 | dev->base_addr = io[this_dev]; | |
1703 | if (io[this_dev] == 0) { | |
1704 | if (this_dev) | |
1705 | break; | |
1706 | printk(KERN_NOTICE "eexpress.c: Module autoprobe not recommended, give io=xx.\n"); | |
1707 | } | |
b1fc5505 | 1708 | if (do_express_probe(dev) == 0) { |
1da177e4 LT |
1709 | dev_eexp[this_dev] = dev; |
1710 | found++; | |
1711 | continue; | |
1712 | } | |
1713 | printk(KERN_WARNING "eexpress.c: Failed to register card at 0x%x.\n", io[this_dev]); | |
1714 | free_netdev(dev); | |
1715 | break; | |
1716 | } | |
1717 | if (found) | |
1718 | return 0; | |
1719 | return -ENXIO; | |
1720 | } | |
1721 | ||
1722 | void cleanup_module(void) | |
1723 | { | |
1724 | int this_dev; | |
1725 | ||
1726 | for (this_dev = 0; this_dev < EEXP_MAX_CARDS; this_dev++) { | |
1727 | struct net_device *dev = dev_eexp[this_dev]; | |
1728 | if (dev) { | |
1729 | unregister_netdev(dev); | |
1730 | free_netdev(dev); | |
1731 | } | |
1732 | } | |
1733 | } | |
1734 | #endif | |
1735 | ||
1736 | /* | |
1737 | * Local Variables: | |
1738 | * c-file-style: "linux" | |
1739 | * tab-width: 8 | |
1740 | * End: | |
1741 | */ |