Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
[deliverable/linux.git] / drivers / net / ethernet / freescale / Kconfig
CommitLineData
ec21e2ec
JK
1#
2# Freescale device configuration
3#
4
5config NET_VENDOR_FREESCALE
6 bool "Freescale devices"
88f07484 7 default y
ec21e2ec
JK
8 depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
9 M523x || M527x || M5272 || M528x || M520x || M532x || \
433aee04 10 ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM)
ec21e2ec
JK
11 ---help---
12 If you have a network (Ethernet) card belonging to this class, say Y
13 and read the Ethernet-HOWTO, available from
14 <http://www.tldp.org/docs.html#howto>.
15
16 Note that the answer to this question doesn't directly affect the
17 kernel: saying N will just cause the configurator to skip all
230dec61
SG
18 the questions about Freescale devices. If you say Y, you will be
19 asked for your specific card in the following questions.
ec21e2ec
JK
20
21if NET_VENDOR_FREESCALE
22
23config FEC
26cf820d 24 tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
ec21e2ec 25 depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
0d903247
WS
26 ARCH_MXC || SOC_IMX28)
27 default ARCH_MXC || SOC_IMX28 if ARM
ec21e2ec 28 select PHYLIB
ff43da86 29 select PTP_1588_CLOCK
ec21e2ec
JK
30 ---help---
31 Say Y here if you want to use the built-in 10/100 Fast ethernet
32 controller on some Motorola ColdFire and Freescale i.MX processors.
33
34config FEC_MPC52xx
35 tristate "FEC MPC52xx driver"
36 depends on PPC_MPC52xx && PPC_BESTCOMM
37 select CRC32
38 select PHYLIB
39 select PPC_BESTCOMM_FEC
40 ---help---
41 This option enables support for the MPC5200's on-chip
42 Fast Ethernet Controller
43 If compiled as module, it will be called fec_mpc52xx.
44
45config FEC_MPC52xx_MDIO
46 bool "FEC MPC52xx MDIO bus driver"
47 depends on FEC_MPC52xx
48 default y
49 ---help---
50 The MPC5200's FEC can connect to the Ethernet either with
51 an external MII PHY chip or 10 Mbps 7-wire interface
52 (Motorola? industry standard).
53 If your board uses an external PHY connected to FEC, enable this.
54 If not sure, enable.
55 If compiled as module, it will be called fec_mpc52xx_phy.
56
57source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
58
59config FSL_PQ_MDIO
60 tristate "Freescale PQ MDIO"
ec21e2ec
JK
61 select PHYLIB
62 ---help---
63 This driver supports the MDIO bus used by the gianfar and UCC drivers.
64
9f35a734
TT
65config FSL_XGMAC_MDIO
66 tristate "Freescale XGMAC MDIO"
9f35a734 67 select PHYLIB
39f33367 68 select OF_MDIO
9f35a734 69 ---help---
1fcf77c8
AF
70 This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
71 on the FMan mEMAC (which supports both Clauses 22 and 45)
9f35a734 72
ec21e2ec
JK
73config UCC_GETH
74 tristate "Freescale QE Gigabit Ethernet"
75 depends on QUICC_ENGINE
76 select FSL_PQ_MDIO
77 select PHYLIB
78 ---help---
79 This driver supports the Gigabit Ethernet mode of the QUICC Engine,
80 which is available on some Freescale SOCs.
81
82config UGETH_TX_ON_DEMAND
83 bool "Transmit on Demand support"
84 depends on UCC_GETH
85
86config GIANFAR
87 tristate "Gianfar Ethernet"
88 depends on FSL_SOC
89 select FSL_PQ_MDIO
90 select PHYLIB
91 select CRC32
92 ---help---
93 This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
94 and MPC86xx family of chips, and the FEC on the 8540.
95
96endif # NET_VENDOR_FREESCALE
This page took 0.332916 seconds and 5 git commands to generate.