projects / deliverable / linux.git / blame
| Commit | Line | Data |
|---|---|---|
| bcc9736c JK |
1 | # |
| 2 | # Micrel device configuration | |
| 3 | # | |
| 4 | ||
| 5 | config NET_VENDOR_MICREL | |
| 6 | bool "Micrel devices" | |
| 88f07484 | 7 | default y |
| bcc9736c JK |
8 | depends on (HAS_IOMEM && DMA_ENGINE) || SPI || PCI || HAS_IOMEM || \ |
| 9 | (ARM && ARCH_KS8695) | |
| 10 | ---help--- | |
| 11 | If you have a network (Ethernet) card belonging to this class, say Y | |
| 12 | and read the Ethernet-HOWTO, available from | |
| 13 | <http://www.tldp.org/docs.html#howto>. | |
| 14 | ||
| 15 | Note that the answer to this question doesn't directly affect the | |
| 16 | kernel: saying N will just cause the configurator to skip all | |
| 17 | the questions about Micrel devices. If you say Y, you will be asked | |
| 18 | for your specific card in the following questions. | |
| 19 | ||
| 20 | if NET_VENDOR_MICREL | |
| 21 | ||
| 22 | config ARM_KS8695_ETHER | |
| 23 | tristate "KS8695 Ethernet support" | |
| 24 | depends on ARM && ARCH_KS8695 | |
| 25 | select MII | |
| 26 | ---help--- | |
| 27 | If you wish to compile a kernel for the KS8695 and want to | |
| 28 | use the internal ethernet then you should answer Y to this. | |
| 29 | ||
| 30 | config KS8842 | |
| 31 | tristate "Micrel KSZ8841/42 with generic bus interface" | |
| 32 | depends on HAS_IOMEM && DMA_ENGINE | |
| 33 | ---help--- | |
| 34 | This platform driver is for KSZ8841(1-port) / KS8842(2-port) | |
| 35 | ethernet switch chip (managed, VLAN, QoS) from Micrel or | |
| 36 | Timberdale(FPGA). | |
| 37 | ||
| 38 | config KS8851 | |
| 39 | tristate "Micrel KS8851 SPI" | |
| 40 | depends on SPI | |
| 41 | select MII | |
| 42 | select CRC32 | |
| 51b7b1c3 | 43 | select EEPROM_93CX6 |
| bcc9736c JK |
44 | ---help--- |
| 45 | SPI driver for Micrel KS8851 SPI attached network chip. | |
| 46 | ||
| 47 | config KS8851_MLL | |
| 48 | tristate "Micrel KS8851 MLL" | |
| 49 | depends on HAS_IOMEM | |
| 50 | select MII | |
| 51 | ---help--- | |
| 52 | This platform driver is for Micrel KS8851 Address/data bus | |
| 53 | multiplexed network chip. | |
| 54 | ||
| 55 | config KSZ884X_PCI | |
| 56 | tristate "Micrel KSZ8841/2 PCI" | |
| 57 | depends on PCI | |
| 58 | select MII | |
| 59 | select CRC32 | |
| 60 | ---help--- | |
| 61 | This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip. | |
| 62 | ||
| 63 | To compile this driver as a module, choose M here. The module | |
| 64 | will be called ksz884x. | |
| 65 | ||
| 66 | endif # NET_VENDOR_MICREL |