Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* hamachi.c: A Packet Engines GNIC-II Gigabit Ethernet driver for Linux. */ |
2 | /* | |
3 | Written 1998-2000 by Donald Becker. | |
4 | Updates 2000 by Keith Underwood. | |
5 | ||
6 | This software may be used and distributed according to the terms of | |
7 | the GNU General Public License (GPL), incorporated herein by reference. | |
8 | Drivers based on or derived from this code fall under the GPL and must | |
9 | retain the authorship, copyright and license notice. This file is not | |
10 | a complete program and may only be used when the entire operating | |
11 | system is licensed under the GPL. | |
12 | ||
13 | The author may be reached as becker@scyld.com, or C/O | |
14 | Scyld Computing Corporation | |
15 | 410 Severn Ave., Suite 210 | |
16 | Annapolis MD 21403 | |
17 | ||
18 | This driver is for the Packet Engines GNIC-II PCI Gigabit Ethernet | |
19 | adapter. | |
20 | ||
21 | Support and updates available at | |
22 | http://www.scyld.com/network/hamachi.html | |
23 | or | |
24 | http://www.parl.clemson.edu/~keithu/hamachi.html | |
25 | ||
26 | ||
27 | ||
28 | Linux kernel changelog: | |
29 | ||
30 | LK1.0.1: | |
31 | - fix lack of pci_dev<->dev association | |
32 | - ethtool support (jgarzik) | |
33 | ||
34 | */ | |
35 | ||
36 | #define DRV_NAME "hamachi" | |
37 | #define DRV_VERSION "1.01+LK1.0.1" | |
38 | #define DRV_RELDATE "5/18/2001" | |
39 | ||
40 | ||
41 | /* A few user-configurable values. */ | |
42 | ||
43 | static int debug = 1; /* 1 normal messages, 0 quiet .. 7 verbose. */ | |
44 | #define final_version | |
45 | #define hamachi_debug debug | |
46 | /* Maximum events (Rx packets, etc.) to handle at each interrupt. */ | |
47 | static int max_interrupt_work = 40; | |
48 | static int mtu; | |
49 | /* Default values selected by testing on a dual processor PIII-450 */ | |
50 | /* These six interrupt control parameters may be set directly when loading the | |
51 | * module, or through the rx_params and tx_params variables | |
52 | */ | |
53 | static int max_rx_latency = 0x11; | |
54 | static int max_rx_gap = 0x05; | |
55 | static int min_rx_pkt = 0x18; | |
56 | static int max_tx_latency = 0x00; | |
57 | static int max_tx_gap = 0x00; | |
58 | static int min_tx_pkt = 0x30; | |
59 | ||
60 | /* Set the copy breakpoint for the copy-only-tiny-frames scheme. | |
61 | -Setting to > 1518 causes all frames to be copied | |
62 | -Setting to 0 disables copies | |
63 | */ | |
64 | static int rx_copybreak; | |
65 | ||
66 | /* An override for the hardware detection of bus width. | |
67 | Set to 1 to force 32 bit PCI bus detection. Set to 4 to force 64 bit. | |
68 | Add 2 to disable parity detection. | |
69 | */ | |
70 | static int force32; | |
71 | ||
72 | ||
73 | /* Used to pass the media type, etc. | |
74 | These exist for driver interoperability. | |
75 | No media types are currently defined. | |
76 | - The lower 4 bits are reserved for the media type. | |
77 | - The next three bits may be set to one of the following: | |
78 | 0x00000000 : Autodetect PCI bus | |
79 | 0x00000010 : Force 32 bit PCI bus | |
80 | 0x00000020 : Disable parity detection | |
81 | 0x00000040 : Force 64 bit PCI bus | |
82 | Default is autodetect | |
83 | - The next bit can be used to force half-duplex. This is a bad | |
84 | idea since no known implementations implement half-duplex, and, | |
85 | in general, half-duplex for gigabit ethernet is a bad idea. | |
86 | 0x00000080 : Force half-duplex | |
87 | Default is full-duplex. | |
88 | - In the original driver, the ninth bit could be used to force | |
89 | full-duplex. Maintain that for compatibility | |
90 | 0x00000200 : Force full-duplex | |
91 | */ | |
92 | #define MAX_UNITS 8 /* More are supported, limit only on options */ | |
93 | static int options[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1}; | |
94 | static int full_duplex[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1}; | |
95 | /* The Hamachi chipset supports 3 parameters each for Rx and Tx | |
96 | * interruput management. Parameters will be loaded as specified into | |
97 | * the TxIntControl and RxIntControl registers. | |
98 | * | |
99 | * The registers are arranged as follows: | |
100 | * 23 - 16 15 - 8 7 - 0 | |
101 | * _________________________________ | |
102 | * | min_pkt | max_gap | max_latency | | |
103 | * --------------------------------- | |
104 | * min_pkt : The minimum number of packets processed between | |
105 | * interrupts. | |
106 | * max_gap : The maximum inter-packet gap in units of 8.192 us | |
107 | * max_latency : The absolute time between interrupts in units of 8.192 us | |
108 | * | |
109 | */ | |
110 | static int rx_params[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1}; | |
111 | static int tx_params[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1}; | |
112 | ||
113 | /* Operational parameters that are set at compile time. */ | |
114 | ||
115 | /* Keep the ring sizes a power of two for compile efficiency. | |
116 | The compiler will convert <unsigned>'%'<2^N> into a bit mask. | |
117 | Making the Tx ring too large decreases the effectiveness of channel | |
118 | bonding and packet priority. | |
119 | There are no ill effects from too-large receive rings, except for | |
120 | excessive memory usage */ | |
121 | /* Empirically it appears that the Tx ring needs to be a little bigger | |
122 | for these Gbit adapters or you get into an overrun condition really | |
123 | easily. Also, things appear to work a bit better in back-to-back | |
124 | configurations if the Rx ring is 8 times the size of the Tx ring | |
125 | */ | |
126 | #define TX_RING_SIZE 64 | |
127 | #define RX_RING_SIZE 512 | |
128 | #define TX_TOTAL_SIZE TX_RING_SIZE*sizeof(struct hamachi_desc) | |
129 | #define RX_TOTAL_SIZE RX_RING_SIZE*sizeof(struct hamachi_desc) | |
130 | ||
131 | /* | |
132 | * Enable netdev_ioctl. Added interrupt coalescing parameter adjustment. | |
133 | * 2/19/99 Pete Wyckoff <wyckoff@ca.sandia.gov> | |
134 | */ | |
135 | ||
136 | /* play with 64-bit addrlen; seems to be a teensy bit slower --pw */ | |
137 | /* #define ADDRLEN 64 */ | |
138 | ||
139 | /* | |
140 | * RX_CHECKSUM turns on card-generated receive checksum generation for | |
141 | * TCP and UDP packets. Otherwise the upper layers do the calculation. | |
142 | * TX_CHECKSUM won't do anything too useful, even if it works. There's no | |
143 | * easy mechanism by which to tell the TCP/UDP stack that it need not | |
144 | * generate checksums for this device. But if somebody can find a way | |
145 | * to get that to work, most of the card work is in here already. | |
146 | * 3/10/1999 Pete Wyckoff <wyckoff@ca.sandia.gov> | |
147 | */ | |
148 | #undef TX_CHECKSUM | |
149 | #define RX_CHECKSUM | |
150 | ||
151 | /* Operational parameters that usually are not changed. */ | |
152 | /* Time in jiffies before concluding the transmitter is hung. */ | |
153 | #define TX_TIMEOUT (5*HZ) | |
154 | ||
155 | #include <linux/module.h> | |
156 | #include <linux/kernel.h> | |
157 | #include <linux/string.h> | |
158 | #include <linux/timer.h> | |
159 | #include <linux/time.h> | |
160 | #include <linux/errno.h> | |
161 | #include <linux/ioport.h> | |
162 | #include <linux/slab.h> | |
163 | #include <linux/interrupt.h> | |
164 | #include <linux/pci.h> | |
165 | #include <linux/init.h> | |
166 | #include <linux/ethtool.h> | |
167 | #include <linux/mii.h> | |
168 | #include <linux/netdevice.h> | |
169 | #include <linux/etherdevice.h> | |
170 | #include <linux/skbuff.h> | |
171 | #include <linux/ip.h> | |
172 | #include <linux/delay.h> | |
173 | #include <linux/bitops.h> | |
174 | ||
175 | #include <asm/uaccess.h> | |
176 | #include <asm/processor.h> /* Processor type for cache alignment. */ | |
177 | #include <asm/io.h> | |
178 | #include <asm/unaligned.h> | |
179 | #include <asm/cache.h> | |
180 | ||
181 | static char version[] __devinitdata = | |
182 | KERN_INFO DRV_NAME ".c:v" DRV_VERSION " " DRV_RELDATE " Written by Donald Becker\n" | |
183 | KERN_INFO " Some modifications by Eric kasten <kasten@nscl.msu.edu>\n" | |
184 | KERN_INFO " Further modifications by Keith Underwood <keithu@parl.clemson.edu>\n"; | |
185 | ||
186 | ||
187 | /* IP_MF appears to be only defined in <netinet/ip.h>, however, | |
188 | we need it for hardware checksumming support. FYI... some of | |
189 | the definitions in <netinet/ip.h> conflict/duplicate those in | |
190 | other linux headers causing many compiler warnings. | |
191 | */ | |
192 | #ifndef IP_MF | |
193 | #define IP_MF 0x2000 /* IP more frags from <netinet/ip.h> */ | |
194 | #endif | |
195 | ||
196 | /* Define IP_OFFSET to be IPOPT_OFFSET */ | |
197 | #ifndef IP_OFFSET | |
198 | #ifdef IPOPT_OFFSET | |
199 | #define IP_OFFSET IPOPT_OFFSET | |
200 | #else | |
201 | #define IP_OFFSET 2 | |
202 | #endif | |
203 | #endif | |
204 | ||
205 | #define RUN_AT(x) (jiffies + (x)) | |
206 | ||
f20badbe Z |
207 | #ifndef ADDRLEN |
208 | #define ADDRLEN 32 | |
209 | #endif | |
210 | ||
1da177e4 LT |
211 | /* Condensed bus+endian portability operations. */ |
212 | #if ADDRLEN == 64 | |
213 | #define cpu_to_leXX(addr) cpu_to_le64(addr) | |
214 | #else | |
215 | #define cpu_to_leXX(addr) cpu_to_le32(addr) | |
216 | #endif | |
217 | ||
218 | ||
219 | /* | |
220 | Theory of Operation | |
221 | ||
222 | I. Board Compatibility | |
223 | ||
224 | This device driver is designed for the Packet Engines "Hamachi" | |
225 | Gigabit Ethernet chip. The only PCA currently supported is the GNIC-II 64-bit | |
226 | 66Mhz PCI card. | |
227 | ||
228 | II. Board-specific settings | |
229 | ||
230 | No jumpers exist on the board. The chip supports software correction of | |
231 | various motherboard wiring errors, however this driver does not support | |
232 | that feature. | |
233 | ||
234 | III. Driver operation | |
235 | ||
236 | IIIa. Ring buffers | |
237 | ||
238 | The Hamachi uses a typical descriptor based bus-master architecture. | |
239 | The descriptor list is similar to that used by the Digital Tulip. | |
240 | This driver uses two statically allocated fixed-size descriptor lists | |
241 | formed into rings by a branch from the final descriptor to the beginning of | |
242 | the list. The ring sizes are set at compile time by RX/TX_RING_SIZE. | |
243 | ||
244 | This driver uses a zero-copy receive and transmit scheme similar my other | |
245 | network drivers. | |
246 | The driver allocates full frame size skbuffs for the Rx ring buffers at | |
247 | open() time and passes the skb->data field to the Hamachi as receive data | |
248 | buffers. When an incoming frame is less than RX_COPYBREAK bytes long, | |
249 | a fresh skbuff is allocated and the frame is copied to the new skbuff. | |
250 | When the incoming frame is larger, the skbuff is passed directly up the | |
251 | protocol stack and replaced by a newly allocated skbuff. | |
252 | ||
253 | The RX_COPYBREAK value is chosen to trade-off the memory wasted by | |
254 | using a full-sized skbuff for small frames vs. the copying costs of larger | |
255 | frames. Gigabit cards are typically used on generously configured machines | |
256 | and the underfilled buffers have negligible impact compared to the benefit of | |
257 | a single allocation size, so the default value of zero results in never | |
258 | copying packets. | |
259 | ||
260 | IIIb/c. Transmit/Receive Structure | |
261 | ||
262 | The Rx and Tx descriptor structure are straight-forward, with no historical | |
263 | baggage that must be explained. Unlike the awkward DBDMA structure, there | |
264 | are no unused fields or option bits that had only one allowable setting. | |
265 | ||
266 | Two details should be noted about the descriptors: The chip supports both 32 | |
267 | bit and 64 bit address structures, and the length field is overwritten on | |
268 | the receive descriptors. The descriptor length is set in the control word | |
269 | for each channel. The development driver uses 32 bit addresses only, however | |
270 | 64 bit addresses may be enabled for 64 bit architectures e.g. the Alpha. | |
271 | ||
272 | IIId. Synchronization | |
273 | ||
274 | This driver is very similar to my other network drivers. | |
275 | The driver runs as two independent, single-threaded flows of control. One | |
276 | is the send-packet routine, which enforces single-threaded use by the | |
277 | dev->tbusy flag. The other thread is the interrupt handler, which is single | |
278 | threaded by the hardware and other software. | |
279 | ||
280 | The send packet thread has partial control over the Tx ring and 'dev->tbusy' | |
281 | flag. It sets the tbusy flag whenever it's queuing a Tx packet. If the next | |
282 | queue slot is empty, it clears the tbusy flag when finished otherwise it sets | |
283 | the 'hmp->tx_full' flag. | |
284 | ||
285 | The interrupt handler has exclusive control over the Rx ring and records stats | |
286 | from the Tx ring. After reaping the stats, it marks the Tx queue entry as | |
287 | empty by incrementing the dirty_tx mark. Iff the 'hmp->tx_full' flag is set, it | |
288 | clears both the tx_full and tbusy flags. | |
289 | ||
290 | IV. Notes | |
291 | ||
292 | Thanks to Kim Stearns of Packet Engines for providing a pair of GNIC-II boards. | |
293 | ||
294 | IVb. References | |
295 | ||
296 | Hamachi Engineering Design Specification, 5/15/97 | |
297 | (Note: This version was marked "Confidential".) | |
298 | ||
299 | IVc. Errata | |
300 | ||
301 | None noted. | |
302 | ||
303 | V. Recent Changes | |
304 | ||
305 | 01/15/1999 EPK Enlargement of the TX and RX ring sizes. This appears | |
306 | to help avoid some stall conditions -- this needs further research. | |
307 | ||
308 | 01/15/1999 EPK Creation of the hamachi_tx function. This function cleans | |
309 | the Tx ring and is called from hamachi_start_xmit (this used to be | |
310 | called from hamachi_interrupt but it tends to delay execution of the | |
311 | interrupt handler and thus reduce bandwidth by reducing the latency | |
312 | between hamachi_rx()'s). Notably, some modification has been made so | |
313 | that the cleaning loop checks only to make sure that the DescOwn bit | |
314 | isn't set in the status flag since the card is not required | |
315 | to set the entire flag to zero after processing. | |
316 | ||
317 | 01/15/1999 EPK In the hamachi_start_tx function, the Tx ring full flag is | |
318 | checked before attempting to add a buffer to the ring. If the ring is full | |
319 | an attempt is made to free any dirty buffers and thus find space for | |
320 | the new buffer or the function returns non-zero which should case the | |
321 | scheduler to reschedule the buffer later. | |
322 | ||
323 | 01/15/1999 EPK Some adjustments were made to the chip initialization. | |
324 | End-to-end flow control should now be fully active and the interrupt | |
325 | algorithm vars have been changed. These could probably use further tuning. | |
326 | ||
327 | 01/15/1999 EPK Added the max_{rx,tx}_latency options. These are used to | |
328 | set the rx and tx latencies for the Hamachi interrupts. If you're having | |
329 | problems with network stalls, try setting these to higher values. | |
330 | Valid values are 0x00 through 0xff. | |
331 | ||
332 | 01/15/1999 EPK In general, the overall bandwidth has increased and | |
333 | latencies are better (sometimes by a factor of 2). Stalls are rare at | |
334 | this point, however there still appears to be a bug somewhere between the | |
335 | hardware and driver. TCP checksum errors under load also appear to be | |
336 | eliminated at this point. | |
337 | ||
338 | 01/18/1999 EPK Ensured that the DescEndRing bit was being set on both the | |
339 | Rx and Tx rings. This appears to have been affecting whether a particular | |
340 | peer-to-peer connection would hang under high load. I believe the Rx | |
341 | rings was typically getting set correctly, but the Tx ring wasn't getting | |
342 | the DescEndRing bit set during initialization. ??? Does this mean the | |
343 | hamachi card is using the DescEndRing in processing even if a particular | |
344 | slot isn't in use -- hypothetically, the card might be searching the | |
345 | entire Tx ring for slots with the DescOwn bit set and then processing | |
346 | them. If the DescEndRing bit isn't set, then it might just wander off | |
347 | through memory until it hits a chunk of data with that bit set | |
348 | and then looping back. | |
349 | ||
350 | 02/09/1999 EPK Added Michel Mueller's TxDMA Interrupt and Tx-timeout | |
351 | problem (TxCmd and RxCmd need only to be set when idle or stopped. | |
352 | ||
353 | 02/09/1999 EPK Added code to check/reset dev->tbusy in hamachi_interrupt. | |
354 | (Michel Mueller pointed out the ``permanently busy'' potential | |
355 | problem here). | |
356 | ||
357 | 02/22/1999 EPK Added Pete Wyckoff's ioctl to control the Tx/Rx latencies. | |
358 | ||
359 | 02/23/1999 EPK Verified that the interrupt status field bits for Tx were | |
360 | incorrectly defined and corrected (as per Michel Mueller). | |
361 | ||
362 | 02/23/1999 EPK Corrected the Tx full check to check that at least 4 slots | |
363 | were available before reseting the tbusy and tx_full flags | |
364 | (as per Michel Mueller). | |
365 | ||
366 | 03/11/1999 EPK Added Pete Wyckoff's hardware checksumming support. | |
367 | ||
368 | 12/31/1999 KDU Cleaned up assorted things and added Don's code to force | |
369 | 32 bit. | |
370 | ||
371 | 02/20/2000 KDU Some of the control was just plain odd. Cleaned up the | |
372 | hamachi_start_xmit() and hamachi_interrupt() code. There is still some | |
373 | re-structuring I would like to do. | |
374 | ||
375 | 03/01/2000 KDU Experimenting with a WIDE range of interrupt mitigation | |
376 | parameters on a dual P3-450 setup yielded the new default interrupt | |
377 | mitigation parameters. Tx should interrupt VERY infrequently due to | |
378 | Eric's scheme. Rx should be more often... | |
379 | ||
380 | 03/13/2000 KDU Added a patch to make the Rx Checksum code interact | |
381 | nicely with non-linux machines. | |
382 | ||
383 | 03/13/2000 KDU Experimented with some of the configuration values: | |
384 | ||
385 | -It seems that enabling PCI performance commands for descriptors | |
386 | (changing RxDMACtrl and TxDMACtrl lower nibble from 5 to D) has minimal | |
387 | performance impact for any of my tests. (ttcp, netpipe, netperf) I will | |
388 | leave them that way until I hear further feedback. | |
389 | ||
390 | -Increasing the PCI_LATENCY_TIMER to 130 | |
391 | (2 + (burst size of 128 * (0 wait states + 1))) seems to slightly | |
392 | degrade performance. Leaving default at 64 pending further information. | |
393 | ||
394 | 03/14/2000 KDU Further tuning: | |
395 | ||
396 | -adjusted boguscnt in hamachi_rx() to depend on interrupt | |
397 | mitigation parameters chosen. | |
398 | ||
399 | -Selected a set of interrupt parameters based on some extensive testing. | |
400 | These may change with more testing. | |
401 | ||
402 | TO DO: | |
403 | ||
404 | -Consider borrowing from the acenic driver code to check PCI_COMMAND for | |
405 | PCI_COMMAND_INVALIDATE. Set maximum burst size to cache line size in | |
406 | that case. | |
407 | ||
408 | -fix the reset procedure. It doesn't quite work. | |
409 | */ | |
410 | ||
411 | /* A few values that may be tweaked. */ | |
412 | /* Size of each temporary Rx buffer, calculated as: | |
413 | * 1518 bytes (ethernet packet) + 2 bytes (to get 8 byte alignment for | |
414 | * the card) + 8 bytes of status info + 8 bytes for the Rx Checksum + | |
415 | * 2 more because we use skb_reserve. | |
416 | */ | |
417 | #define PKT_BUF_SZ 1538 | |
418 | ||
419 | /* For now, this is going to be set to the maximum size of an ethernet | |
420 | * packet. Eventually, we may want to make it a variable that is | |
421 | * related to the MTU | |
422 | */ | |
423 | #define MAX_FRAME_SIZE 1518 | |
424 | ||
425 | /* The rest of these values should never change. */ | |
426 | ||
427 | static void hamachi_timer(unsigned long data); | |
428 | ||
429 | enum capability_flags {CanHaveMII=1, }; | |
f71e1309 | 430 | static const struct chip_info { |
1da177e4 LT |
431 | u16 vendor_id, device_id, device_id_mask, pad; |
432 | const char *name; | |
433 | void (*media_timer)(unsigned long data); | |
434 | int flags; | |
435 | } chip_tbl[] = { | |
436 | {0x1318, 0x0911, 0xffff, 0, "Hamachi GNIC-II", hamachi_timer, 0}, | |
437 | {0,}, | |
438 | }; | |
439 | ||
440 | /* Offsets to the Hamachi registers. Various sizes. */ | |
441 | enum hamachi_offsets { | |
442 | TxDMACtrl=0x00, TxCmd=0x04, TxStatus=0x06, TxPtr=0x08, TxCurPtr=0x10, | |
443 | RxDMACtrl=0x20, RxCmd=0x24, RxStatus=0x26, RxPtr=0x28, RxCurPtr=0x30, | |
444 | PCIClkMeas=0x060, MiscStatus=0x066, ChipRev=0x68, ChipReset=0x06B, | |
445 | LEDCtrl=0x06C, VirtualJumpers=0x06D, GPIO=0x6E, | |
446 | TxChecksum=0x074, RxChecksum=0x076, | |
447 | TxIntrCtrl=0x078, RxIntrCtrl=0x07C, | |
448 | InterruptEnable=0x080, InterruptClear=0x084, IntrStatus=0x088, | |
449 | EventStatus=0x08C, | |
450 | MACCnfg=0x0A0, FrameGap0=0x0A2, FrameGap1=0x0A4, | |
451 | /* See enum MII_offsets below. */ | |
452 | MACCnfg2=0x0B0, RxDepth=0x0B8, FlowCtrl=0x0BC, MaxFrameSize=0x0CE, | |
453 | AddrMode=0x0D0, StationAddr=0x0D2, | |
454 | /* Gigabit AutoNegotiation. */ | |
455 | ANCtrl=0x0E0, ANStatus=0x0E2, ANXchngCtrl=0x0E4, ANAdvertise=0x0E8, | |
456 | ANLinkPartnerAbility=0x0EA, | |
457 | EECmdStatus=0x0F0, EEData=0x0F1, EEAddr=0x0F2, | |
458 | FIFOcfg=0x0F8, | |
459 | }; | |
460 | ||
461 | /* Offsets to the MII-mode registers. */ | |
462 | enum MII_offsets { | |
463 | MII_Cmd=0xA6, MII_Addr=0xA8, MII_Wr_Data=0xAA, MII_Rd_Data=0xAC, | |
464 | MII_Status=0xAE, | |
465 | }; | |
466 | ||
467 | /* Bits in the interrupt status/mask registers. */ | |
468 | enum intr_status_bits { | |
469 | IntrRxDone=0x01, IntrRxPCIFault=0x02, IntrRxPCIErr=0x04, | |
470 | IntrTxDone=0x100, IntrTxPCIFault=0x200, IntrTxPCIErr=0x400, | |
471 | LinkChange=0x10000, NegotiationChange=0x20000, StatsMax=0x40000, }; | |
472 | ||
473 | /* The Hamachi Rx and Tx buffer descriptors. */ | |
474 | struct hamachi_desc { | |
475 | u32 status_n_length; | |
476 | #if ADDRLEN == 64 | |
477 | u32 pad; | |
478 | u64 addr; | |
479 | #else | |
480 | u32 addr; | |
481 | #endif | |
482 | }; | |
483 | ||
484 | /* Bits in hamachi_desc.status_n_length */ | |
485 | enum desc_status_bits { | |
486 | DescOwn=0x80000000, DescEndPacket=0x40000000, DescEndRing=0x20000000, | |
487 | DescIntr=0x10000000, | |
488 | }; | |
489 | ||
490 | #define PRIV_ALIGN 15 /* Required alignment mask */ | |
491 | #define MII_CNT 4 | |
492 | struct hamachi_private { | |
493 | /* Descriptor rings first for alignment. Tx requires a second descriptor | |
494 | for status. */ | |
495 | struct hamachi_desc *rx_ring; | |
496 | struct hamachi_desc *tx_ring; | |
497 | struct sk_buff* rx_skbuff[RX_RING_SIZE]; | |
498 | struct sk_buff* tx_skbuff[TX_RING_SIZE]; | |
499 | dma_addr_t tx_ring_dma; | |
500 | dma_addr_t rx_ring_dma; | |
501 | struct net_device_stats stats; | |
502 | struct timer_list timer; /* Media selection timer. */ | |
503 | /* Frequently used and paired value: keep adjacent for cache effect. */ | |
504 | spinlock_t lock; | |
505 | int chip_id; | |
506 | unsigned int cur_rx, dirty_rx; /* Producer/consumer ring indices */ | |
507 | unsigned int cur_tx, dirty_tx; | |
508 | unsigned int rx_buf_sz; /* Based on MTU+slack. */ | |
509 | unsigned int tx_full:1; /* The Tx queue is full. */ | |
510 | unsigned int duplex_lock:1; | |
511 | unsigned int default_port:4; /* Last dev->if_port value. */ | |
512 | /* MII transceiver section. */ | |
513 | int mii_cnt; /* MII device addresses. */ | |
514 | struct mii_if_info mii_if; /* MII lib hooks/info */ | |
515 | unsigned char phys[MII_CNT]; /* MII device addresses, only first one used. */ | |
516 | u32 rx_int_var, tx_int_var; /* interrupt control variables */ | |
517 | u32 option; /* Hold on to a copy of the options */ | |
518 | struct pci_dev *pci_dev; | |
519 | void __iomem *base; | |
520 | }; | |
521 | ||
522 | MODULE_AUTHOR("Donald Becker <becker@scyld.com>, Eric Kasten <kasten@nscl.msu.edu>, Keith Underwood <keithu@parl.clemson.edu>"); | |
523 | MODULE_DESCRIPTION("Packet Engines 'Hamachi' GNIC-II Gigabit Ethernet driver"); | |
524 | MODULE_LICENSE("GPL"); | |
525 | ||
526 | module_param(max_interrupt_work, int, 0); | |
527 | module_param(mtu, int, 0); | |
528 | module_param(debug, int, 0); | |
529 | module_param(min_rx_pkt, int, 0); | |
530 | module_param(max_rx_gap, int, 0); | |
531 | module_param(max_rx_latency, int, 0); | |
532 | module_param(min_tx_pkt, int, 0); | |
533 | module_param(max_tx_gap, int, 0); | |
534 | module_param(max_tx_latency, int, 0); | |
535 | module_param(rx_copybreak, int, 0); | |
536 | module_param_array(rx_params, int, NULL, 0); | |
537 | module_param_array(tx_params, int, NULL, 0); | |
538 | module_param_array(options, int, NULL, 0); | |
539 | module_param_array(full_duplex, int, NULL, 0); | |
540 | module_param(force32, int, 0); | |
541 | MODULE_PARM_DESC(max_interrupt_work, "GNIC-II maximum events handled per interrupt"); | |
542 | MODULE_PARM_DESC(mtu, "GNIC-II MTU (all boards)"); | |
543 | MODULE_PARM_DESC(debug, "GNIC-II debug level (0-7)"); | |
544 | MODULE_PARM_DESC(min_rx_pkt, "GNIC-II minimum Rx packets processed between interrupts"); | |
545 | MODULE_PARM_DESC(max_rx_gap, "GNIC-II maximum Rx inter-packet gap in 8.192 microsecond units"); | |
546 | MODULE_PARM_DESC(max_rx_latency, "GNIC-II time between Rx interrupts in 8.192 microsecond units"); | |
547 | MODULE_PARM_DESC(min_tx_pkt, "GNIC-II minimum Tx packets processed between interrupts"); | |
548 | MODULE_PARM_DESC(max_tx_gap, "GNIC-II maximum Tx inter-packet gap in 8.192 microsecond units"); | |
549 | MODULE_PARM_DESC(max_tx_latency, "GNIC-II time between Tx interrupts in 8.192 microsecond units"); | |
550 | MODULE_PARM_DESC(rx_copybreak, "GNIC-II copy breakpoint for copy-only-tiny-frames"); | |
551 | MODULE_PARM_DESC(rx_params, "GNIC-II min_rx_pkt+max_rx_gap+max_rx_latency"); | |
552 | MODULE_PARM_DESC(tx_params, "GNIC-II min_tx_pkt+max_tx_gap+max_tx_latency"); | |
553 | MODULE_PARM_DESC(options, "GNIC-II Bits 0-3: media type, bits 4-6: as force32, bit 7: half duplex, bit 9 full duplex"); | |
554 | MODULE_PARM_DESC(full_duplex, "GNIC-II full duplex setting(s) (1)"); | |
555 | MODULE_PARM_DESC(force32, "GNIC-II: Bit 0: 32 bit PCI, bit 1: disable parity, bit 2: 64 bit PCI (all boards)"); | |
556 | ||
557 | static int read_eeprom(void __iomem *ioaddr, int location); | |
558 | static int mdio_read(struct net_device *dev, int phy_id, int location); | |
559 | static void mdio_write(struct net_device *dev, int phy_id, int location, int value); | |
560 | static int hamachi_open(struct net_device *dev); | |
561 | static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); | |
562 | static void hamachi_timer(unsigned long data); | |
563 | static void hamachi_tx_timeout(struct net_device *dev); | |
564 | static void hamachi_init_ring(struct net_device *dev); | |
565 | static int hamachi_start_xmit(struct sk_buff *skb, struct net_device *dev); | |
566 | static irqreturn_t hamachi_interrupt(int irq, void *dev_instance, struct pt_regs *regs); | |
567 | static int hamachi_rx(struct net_device *dev); | |
568 | static inline int hamachi_tx(struct net_device *dev); | |
569 | static void hamachi_error(struct net_device *dev, int intr_status); | |
570 | static int hamachi_close(struct net_device *dev); | |
571 | static struct net_device_stats *hamachi_get_stats(struct net_device *dev); | |
572 | static void set_rx_mode(struct net_device *dev); | |
573 | static struct ethtool_ops ethtool_ops; | |
574 | static struct ethtool_ops ethtool_ops_no_mii; | |
575 | ||
576 | static int __devinit hamachi_init_one (struct pci_dev *pdev, | |
577 | const struct pci_device_id *ent) | |
578 | { | |
579 | struct hamachi_private *hmp; | |
580 | int option, i, rx_int_var, tx_int_var, boguscnt; | |
581 | int chip_id = ent->driver_data; | |
582 | int irq; | |
583 | void __iomem *ioaddr; | |
584 | unsigned long base; | |
585 | static int card_idx; | |
586 | struct net_device *dev; | |
587 | void *ring_space; | |
588 | dma_addr_t ring_dma; | |
589 | int ret = -ENOMEM; | |
590 | ||
591 | /* when built into the kernel, we only print version if device is found */ | |
592 | #ifndef MODULE | |
593 | static int printed_version; | |
594 | if (!printed_version++) | |
595 | printk(version); | |
596 | #endif | |
597 | ||
598 | if (pci_enable_device(pdev)) { | |
599 | ret = -EIO; | |
600 | goto err_out; | |
601 | } | |
602 | ||
603 | base = pci_resource_start(pdev, 0); | |
604 | #ifdef __alpha__ /* Really "64 bit addrs" */ | |
605 | base |= (pci_resource_start(pdev, 1) << 32); | |
606 | #endif | |
607 | ||
608 | pci_set_master(pdev); | |
609 | ||
610 | i = pci_request_regions(pdev, DRV_NAME); | |
611 | if (i) return i; | |
612 | ||
613 | irq = pdev->irq; | |
614 | ioaddr = ioremap(base, 0x400); | |
615 | if (!ioaddr) | |
616 | goto err_out_release; | |
617 | ||
618 | dev = alloc_etherdev(sizeof(struct hamachi_private)); | |
619 | if (!dev) | |
620 | goto err_out_iounmap; | |
621 | ||
622 | SET_MODULE_OWNER(dev); | |
623 | SET_NETDEV_DEV(dev, &pdev->dev); | |
624 | ||
625 | #ifdef TX_CHECKSUM | |
626 | printk("check that skbcopy in ip_queue_xmit isn't happening\n"); | |
627 | dev->hard_header_len += 8; /* for cksum tag */ | |
628 | #endif | |
629 | ||
630 | for (i = 0; i < 6; i++) | |
631 | dev->dev_addr[i] = 1 ? read_eeprom(ioaddr, 4 + i) | |
632 | : readb(ioaddr + StationAddr + i); | |
633 | ||
634 | #if ! defined(final_version) | |
635 | if (hamachi_debug > 4) | |
636 | for (i = 0; i < 0x10; i++) | |
637 | printk("%2.2x%s", | |
638 | read_eeprom(ioaddr, i), i % 16 != 15 ? " " : "\n"); | |
639 | #endif | |
640 | ||
641 | hmp = netdev_priv(dev); | |
642 | spin_lock_init(&hmp->lock); | |
643 | ||
644 | hmp->mii_if.dev = dev; | |
645 | hmp->mii_if.mdio_read = mdio_read; | |
646 | hmp->mii_if.mdio_write = mdio_write; | |
647 | hmp->mii_if.phy_id_mask = 0x1f; | |
648 | hmp->mii_if.reg_num_mask = 0x1f; | |
649 | ||
650 | ring_space = pci_alloc_consistent(pdev, TX_TOTAL_SIZE, &ring_dma); | |
651 | if (!ring_space) | |
652 | goto err_out_cleardev; | |
653 | hmp->tx_ring = (struct hamachi_desc *)ring_space; | |
654 | hmp->tx_ring_dma = ring_dma; | |
655 | ||
656 | ring_space = pci_alloc_consistent(pdev, RX_TOTAL_SIZE, &ring_dma); | |
657 | if (!ring_space) | |
658 | goto err_out_unmap_tx; | |
659 | hmp->rx_ring = (struct hamachi_desc *)ring_space; | |
660 | hmp->rx_ring_dma = ring_dma; | |
661 | ||
662 | /* Check for options being passed in */ | |
663 | option = card_idx < MAX_UNITS ? options[card_idx] : 0; | |
664 | if (dev->mem_start) | |
665 | option = dev->mem_start; | |
666 | ||
667 | /* If the bus size is misidentified, do the following. */ | |
668 | force32 = force32 ? force32 : | |
669 | ((option >= 0) ? ((option & 0x00000070) >> 4) : 0 ); | |
670 | if (force32) | |
671 | writeb(force32, ioaddr + VirtualJumpers); | |
672 | ||
673 | /* Hmmm, do we really need to reset the chip???. */ | |
674 | writeb(0x01, ioaddr + ChipReset); | |
675 | ||
676 | /* After a reset, the clock speed measurement of the PCI bus will not | |
677 | * be valid for a moment. Wait for a little while until it is. If | |
678 | * it takes more than 10ms, forget it. | |
679 | */ | |
680 | udelay(10); | |
681 | i = readb(ioaddr + PCIClkMeas); | |
682 | for (boguscnt = 0; (!(i & 0x080)) && boguscnt < 1000; boguscnt++){ | |
683 | udelay(10); | |
684 | i = readb(ioaddr + PCIClkMeas); | |
685 | } | |
686 | ||
687 | hmp->base = ioaddr; | |
688 | dev->base_addr = (unsigned long)ioaddr; | |
689 | dev->irq = irq; | |
690 | pci_set_drvdata(pdev, dev); | |
691 | ||
692 | hmp->chip_id = chip_id; | |
693 | hmp->pci_dev = pdev; | |
694 | ||
695 | /* The lower four bits are the media type. */ | |
696 | if (option > 0) { | |
697 | hmp->option = option; | |
698 | if (option & 0x200) | |
699 | hmp->mii_if.full_duplex = 1; | |
700 | else if (option & 0x080) | |
701 | hmp->mii_if.full_duplex = 0; | |
702 | hmp->default_port = option & 15; | |
703 | if (hmp->default_port) | |
704 | hmp->mii_if.force_media = 1; | |
705 | } | |
706 | if (card_idx < MAX_UNITS && full_duplex[card_idx] > 0) | |
707 | hmp->mii_if.full_duplex = 1; | |
708 | ||
709 | /* lock the duplex mode if someone specified a value */ | |
710 | if (hmp->mii_if.full_duplex || (option & 0x080)) | |
711 | hmp->duplex_lock = 1; | |
712 | ||
713 | /* Set interrupt tuning parameters */ | |
714 | max_rx_latency = max_rx_latency & 0x00ff; | |
715 | max_rx_gap = max_rx_gap & 0x00ff; | |
716 | min_rx_pkt = min_rx_pkt & 0x00ff; | |
717 | max_tx_latency = max_tx_latency & 0x00ff; | |
718 | max_tx_gap = max_tx_gap & 0x00ff; | |
719 | min_tx_pkt = min_tx_pkt & 0x00ff; | |
720 | ||
721 | rx_int_var = card_idx < MAX_UNITS ? rx_params[card_idx] : -1; | |
722 | tx_int_var = card_idx < MAX_UNITS ? tx_params[card_idx] : -1; | |
723 | hmp->rx_int_var = rx_int_var >= 0 ? rx_int_var : | |
724 | (min_rx_pkt << 16 | max_rx_gap << 8 | max_rx_latency); | |
725 | hmp->tx_int_var = tx_int_var >= 0 ? tx_int_var : | |
726 | (min_tx_pkt << 16 | max_tx_gap << 8 | max_tx_latency); | |
727 | ||
728 | ||
729 | /* The Hamachi-specific entries in the device structure. */ | |
730 | dev->open = &hamachi_open; | |
731 | dev->hard_start_xmit = &hamachi_start_xmit; | |
732 | dev->stop = &hamachi_close; | |
733 | dev->get_stats = &hamachi_get_stats; | |
734 | dev->set_multicast_list = &set_rx_mode; | |
735 | dev->do_ioctl = &netdev_ioctl; | |
736 | if (chip_tbl[hmp->chip_id].flags & CanHaveMII) | |
737 | SET_ETHTOOL_OPS(dev, ðtool_ops); | |
738 | else | |
739 | SET_ETHTOOL_OPS(dev, ðtool_ops_no_mii); | |
740 | dev->tx_timeout = &hamachi_tx_timeout; | |
741 | dev->watchdog_timeo = TX_TIMEOUT; | |
742 | if (mtu) | |
743 | dev->mtu = mtu; | |
744 | ||
745 | i = register_netdev(dev); | |
746 | if (i) { | |
747 | ret = i; | |
748 | goto err_out_unmap_rx; | |
749 | } | |
750 | ||
751 | printk(KERN_INFO "%s: %s type %x at %p, ", | |
752 | dev->name, chip_tbl[chip_id].name, readl(ioaddr + ChipRev), | |
753 | ioaddr); | |
754 | for (i = 0; i < 5; i++) | |
755 | printk("%2.2x:", dev->dev_addr[i]); | |
756 | printk("%2.2x, IRQ %d.\n", dev->dev_addr[i], irq); | |
757 | i = readb(ioaddr + PCIClkMeas); | |
758 | printk(KERN_INFO "%s: %d-bit %d Mhz PCI bus (%d), Virtual Jumpers " | |
759 | "%2.2x, LPA %4.4x.\n", | |
760 | dev->name, readw(ioaddr + MiscStatus) & 1 ? 64 : 32, | |
761 | i ? 2000/(i&0x7f) : 0, i&0x7f, (int)readb(ioaddr + VirtualJumpers), | |
762 | readw(ioaddr + ANLinkPartnerAbility)); | |
763 | ||
764 | if (chip_tbl[hmp->chip_id].flags & CanHaveMII) { | |
765 | int phy, phy_idx = 0; | |
766 | for (phy = 0; phy < 32 && phy_idx < MII_CNT; phy++) { | |
767 | int mii_status = mdio_read(dev, phy, MII_BMSR); | |
768 | if (mii_status != 0xffff && | |
769 | mii_status != 0x0000) { | |
770 | hmp->phys[phy_idx++] = phy; | |
771 | hmp->mii_if.advertising = mdio_read(dev, phy, MII_ADVERTISE); | |
772 | printk(KERN_INFO "%s: MII PHY found at address %d, status " | |
773 | "0x%4.4x advertising %4.4x.\n", | |
774 | dev->name, phy, mii_status, hmp->mii_if.advertising); | |
775 | } | |
776 | } | |
777 | hmp->mii_cnt = phy_idx; | |
778 | if (hmp->mii_cnt > 0) | |
779 | hmp->mii_if.phy_id = hmp->phys[0]; | |
780 | else | |
781 | memset(&hmp->mii_if, 0, sizeof(hmp->mii_if)); | |
782 | } | |
783 | /* Configure gigabit autonegotiation. */ | |
784 | writew(0x0400, ioaddr + ANXchngCtrl); /* Enable legacy links. */ | |
785 | writew(0x08e0, ioaddr + ANAdvertise); /* Set our advertise word. */ | |
786 | writew(0x1000, ioaddr + ANCtrl); /* Enable negotiation */ | |
787 | ||
788 | card_idx++; | |
789 | return 0; | |
790 | ||
791 | err_out_unmap_rx: | |
792 | pci_free_consistent(pdev, RX_TOTAL_SIZE, hmp->rx_ring, | |
793 | hmp->rx_ring_dma); | |
794 | err_out_unmap_tx: | |
795 | pci_free_consistent(pdev, TX_TOTAL_SIZE, hmp->tx_ring, | |
796 | hmp->tx_ring_dma); | |
797 | err_out_cleardev: | |
798 | free_netdev (dev); | |
799 | err_out_iounmap: | |
800 | iounmap(ioaddr); | |
801 | err_out_release: | |
802 | pci_release_regions(pdev); | |
803 | err_out: | |
804 | return ret; | |
805 | } | |
806 | ||
807 | static int __devinit read_eeprom(void __iomem *ioaddr, int location) | |
808 | { | |
809 | int bogus_cnt = 1000; | |
810 | ||
811 | /* We should check busy first - per docs -KDU */ | |
812 | while ((readb(ioaddr + EECmdStatus) & 0x40) && --bogus_cnt > 0); | |
813 | writew(location, ioaddr + EEAddr); | |
814 | writeb(0x02, ioaddr + EECmdStatus); | |
815 | bogus_cnt = 1000; | |
816 | while ((readb(ioaddr + EECmdStatus) & 0x40) && --bogus_cnt > 0); | |
817 | if (hamachi_debug > 5) | |
818 | printk(" EEPROM status is %2.2x after %d ticks.\n", | |
819 | (int)readb(ioaddr + EECmdStatus), 1000- bogus_cnt); | |
820 | return readb(ioaddr + EEData); | |
821 | } | |
822 | ||
823 | /* MII Managemen Data I/O accesses. | |
824 | These routines assume the MDIO controller is idle, and do not exit until | |
825 | the command is finished. */ | |
826 | ||
827 | static int mdio_read(struct net_device *dev, int phy_id, int location) | |
828 | { | |
829 | struct hamachi_private *hmp = netdev_priv(dev); | |
830 | void __iomem *ioaddr = hmp->base; | |
831 | int i; | |
832 | ||
833 | /* We should check busy first - per docs -KDU */ | |
834 | for (i = 10000; i >= 0; i--) | |
835 | if ((readw(ioaddr + MII_Status) & 1) == 0) | |
836 | break; | |
837 | writew((phy_id<<8) + location, ioaddr + MII_Addr); | |
838 | writew(0x0001, ioaddr + MII_Cmd); | |
839 | for (i = 10000; i >= 0; i--) | |
840 | if ((readw(ioaddr + MII_Status) & 1) == 0) | |
841 | break; | |
842 | return readw(ioaddr + MII_Rd_Data); | |
843 | } | |
844 | ||
845 | static void mdio_write(struct net_device *dev, int phy_id, int location, int value) | |
846 | { | |
847 | struct hamachi_private *hmp = netdev_priv(dev); | |
848 | void __iomem *ioaddr = hmp->base; | |
849 | int i; | |
850 | ||
851 | /* We should check busy first - per docs -KDU */ | |
852 | for (i = 10000; i >= 0; i--) | |
853 | if ((readw(ioaddr + MII_Status) & 1) == 0) | |
854 | break; | |
855 | writew((phy_id<<8) + location, ioaddr + MII_Addr); | |
856 | writew(value, ioaddr + MII_Wr_Data); | |
857 | ||
858 | /* Wait for the command to finish. */ | |
859 | for (i = 10000; i >= 0; i--) | |
860 | if ((readw(ioaddr + MII_Status) & 1) == 0) | |
861 | break; | |
862 | return; | |
863 | } | |
864 | ||
865 | \f | |
866 | static int hamachi_open(struct net_device *dev) | |
867 | { | |
868 | struct hamachi_private *hmp = netdev_priv(dev); | |
869 | void __iomem *ioaddr = hmp->base; | |
870 | int i; | |
871 | u32 rx_int_var, tx_int_var; | |
872 | u16 fifo_info; | |
873 | ||
874 | i = request_irq(dev->irq, &hamachi_interrupt, SA_SHIRQ, dev->name, dev); | |
875 | if (i) | |
876 | return i; | |
877 | ||
878 | if (hamachi_debug > 1) | |
879 | printk(KERN_DEBUG "%s: hamachi_open() irq %d.\n", | |
880 | dev->name, dev->irq); | |
881 | ||
882 | hamachi_init_ring(dev); | |
883 | ||
884 | #if ADDRLEN == 64 | |
885 | /* writellll anyone ? */ | |
886 | writel(cpu_to_le64(hmp->rx_ring_dma), ioaddr + RxPtr); | |
887 | writel(cpu_to_le64(hmp->rx_ring_dma) >> 32, ioaddr + RxPtr + 4); | |
888 | writel(cpu_to_le64(hmp->tx_ring_dma), ioaddr + TxPtr); | |
889 | writel(cpu_to_le64(hmp->tx_ring_dma) >> 32, ioaddr + TxPtr + 4); | |
890 | #else | |
891 | writel(cpu_to_le32(hmp->rx_ring_dma), ioaddr + RxPtr); | |
892 | writel(cpu_to_le32(hmp->tx_ring_dma), ioaddr + TxPtr); | |
893 | #endif | |
894 | ||
895 | /* TODO: It would make sense to organize this as words since the card | |
896 | * documentation does. -KDU | |
897 | */ | |
898 | for (i = 0; i < 6; i++) | |
899 | writeb(dev->dev_addr[i], ioaddr + StationAddr + i); | |
900 | ||
901 | /* Initialize other registers: with so many this eventually this will | |
902 | converted to an offset/value list. */ | |
903 | ||
904 | /* Configure the FIFO */ | |
905 | fifo_info = (readw(ioaddr + GPIO) & 0x00C0) >> 6; | |
906 | switch (fifo_info){ | |
907 | case 0 : | |
908 | /* No FIFO */ | |
909 | writew(0x0000, ioaddr + FIFOcfg); | |
910 | break; | |
911 | case 1 : | |
912 | /* Configure the FIFO for 512K external, 16K used for Tx. */ | |
913 | writew(0x0028, ioaddr + FIFOcfg); | |
914 | break; | |
915 | case 2 : | |
916 | /* Configure the FIFO for 1024 external, 32K used for Tx. */ | |
917 | writew(0x004C, ioaddr + FIFOcfg); | |
918 | break; | |
919 | case 3 : | |
920 | /* Configure the FIFO for 2048 external, 32K used for Tx. */ | |
921 | writew(0x006C, ioaddr + FIFOcfg); | |
922 | break; | |
923 | default : | |
924 | printk(KERN_WARNING "%s: Unsupported external memory config!\n", | |
925 | dev->name); | |
926 | /* Default to no FIFO */ | |
927 | writew(0x0000, ioaddr + FIFOcfg); | |
928 | break; | |
929 | } | |
930 | ||
931 | if (dev->if_port == 0) | |
932 | dev->if_port = hmp->default_port; | |
933 | ||
934 | ||
935 | /* Setting the Rx mode will start the Rx process. */ | |
936 | /* If someone didn't choose a duplex, default to full-duplex */ | |
937 | if (hmp->duplex_lock != 1) | |
938 | hmp->mii_if.full_duplex = 1; | |
939 | ||
940 | /* always 1, takes no more time to do it */ | |
941 | writew(0x0001, ioaddr + RxChecksum); | |
942 | #ifdef TX_CHECKSUM | |
943 | writew(0x0001, ioaddr + TxChecksum); | |
944 | #else | |
945 | writew(0x0000, ioaddr + TxChecksum); | |
946 | #endif | |
947 | writew(0x8000, ioaddr + MACCnfg); /* Soft reset the MAC */ | |
948 | writew(0x215F, ioaddr + MACCnfg); | |
949 | writew(0x000C, ioaddr + FrameGap0); | |
950 | /* WHAT?!?!? Why isn't this documented somewhere? -KDU */ | |
951 | writew(0x1018, ioaddr + FrameGap1); | |
952 | /* Why do we enable receives/transmits here? -KDU */ | |
953 | writew(0x0780, ioaddr + MACCnfg2); /* Upper 16 bits control LEDs. */ | |
954 | /* Enable automatic generation of flow control frames, period 0xffff. */ | |
955 | writel(0x0030FFFF, ioaddr + FlowCtrl); | |
956 | writew(MAX_FRAME_SIZE, ioaddr + MaxFrameSize); /* dev->mtu+14 ??? */ | |
957 | ||
958 | /* Enable legacy links. */ | |
959 | writew(0x0400, ioaddr + ANXchngCtrl); /* Enable legacy links. */ | |
960 | /* Initial Link LED to blinking red. */ | |
961 | writeb(0x03, ioaddr + LEDCtrl); | |
962 | ||
963 | /* Configure interrupt mitigation. This has a great effect on | |
964 | performance, so systems tuning should start here!. */ | |
965 | ||
966 | rx_int_var = hmp->rx_int_var; | |
967 | tx_int_var = hmp->tx_int_var; | |
968 | ||
969 | if (hamachi_debug > 1) { | |
970 | printk("max_tx_latency: %d, max_tx_gap: %d, min_tx_pkt: %d\n", | |
971 | tx_int_var & 0x00ff, (tx_int_var & 0x00ff00) >> 8, | |
972 | (tx_int_var & 0x00ff0000) >> 16); | |
973 | printk("max_rx_latency: %d, max_rx_gap: %d, min_rx_pkt: %d\n", | |
974 | rx_int_var & 0x00ff, (rx_int_var & 0x00ff00) >> 8, | |
975 | (rx_int_var & 0x00ff0000) >> 16); | |
976 | printk("rx_int_var: %x, tx_int_var: %x\n", rx_int_var, tx_int_var); | |
977 | } | |
978 | ||
979 | writel(tx_int_var, ioaddr + TxIntrCtrl); | |
980 | writel(rx_int_var, ioaddr + RxIntrCtrl); | |
981 | ||
982 | set_rx_mode(dev); | |
983 | ||
984 | netif_start_queue(dev); | |
985 | ||
986 | /* Enable interrupts by setting the interrupt mask. */ | |
987 | writel(0x80878787, ioaddr + InterruptEnable); | |
988 | writew(0x0000, ioaddr + EventStatus); /* Clear non-interrupting events */ | |
989 | ||
990 | /* Configure and start the DMA channels. */ | |
991 | /* Burst sizes are in the low three bits: size = 4<<(val&7) */ | |
992 | #if ADDRLEN == 64 | |
993 | writew(0x005D, ioaddr + RxDMACtrl); /* 128 dword bursts */ | |
994 | writew(0x005D, ioaddr + TxDMACtrl); | |
995 | #else | |
996 | writew(0x001D, ioaddr + RxDMACtrl); | |
997 | writew(0x001D, ioaddr + TxDMACtrl); | |
998 | #endif | |
999 | writew(0x0001, ioaddr + RxCmd); | |
1000 | ||
1001 | if (hamachi_debug > 2) { | |
1002 | printk(KERN_DEBUG "%s: Done hamachi_open(), status: Rx %x Tx %x.\n", | |
1003 | dev->name, readw(ioaddr + RxStatus), readw(ioaddr + TxStatus)); | |
1004 | } | |
1005 | /* Set the timer to check for link beat. */ | |
1006 | init_timer(&hmp->timer); | |
1007 | hmp->timer.expires = RUN_AT((24*HZ)/10); /* 2.4 sec. */ | |
1008 | hmp->timer.data = (unsigned long)dev; | |
1009 | hmp->timer.function = &hamachi_timer; /* timer handler */ | |
1010 | add_timer(&hmp->timer); | |
1011 | ||
1012 | return 0; | |
1013 | } | |
1014 | ||
1015 | static inline int hamachi_tx(struct net_device *dev) | |
1016 | { | |
1017 | struct hamachi_private *hmp = netdev_priv(dev); | |
1018 | ||
1019 | /* Update the dirty pointer until we find an entry that is | |
1020 | still owned by the card */ | |
1021 | for (; hmp->cur_tx - hmp->dirty_tx > 0; hmp->dirty_tx++) { | |
1022 | int entry = hmp->dirty_tx % TX_RING_SIZE; | |
1023 | struct sk_buff *skb; | |
1024 | ||
1025 | if (hmp->tx_ring[entry].status_n_length & cpu_to_le32(DescOwn)) | |
1026 | break; | |
1027 | /* Free the original skb. */ | |
1028 | skb = hmp->tx_skbuff[entry]; | |
1029 | if (skb != 0) { | |
1030 | pci_unmap_single(hmp->pci_dev, | |
1031 | hmp->tx_ring[entry].addr, skb->len, | |
1032 | PCI_DMA_TODEVICE); | |
1033 | dev_kfree_skb(skb); | |
1034 | hmp->tx_skbuff[entry] = NULL; | |
1035 | } | |
1036 | hmp->tx_ring[entry].status_n_length = 0; | |
1037 | if (entry >= TX_RING_SIZE-1) | |
1038 | hmp->tx_ring[TX_RING_SIZE-1].status_n_length |= | |
1039 | cpu_to_le32(DescEndRing); | |
1040 | hmp->stats.tx_packets++; | |
1041 | } | |
1042 | ||
1043 | return 0; | |
1044 | } | |
1045 | ||
1046 | static void hamachi_timer(unsigned long data) | |
1047 | { | |
1048 | struct net_device *dev = (struct net_device *)data; | |
1049 | struct hamachi_private *hmp = netdev_priv(dev); | |
1050 | void __iomem *ioaddr = hmp->base; | |
1051 | int next_tick = 10*HZ; | |
1052 | ||
1053 | if (hamachi_debug > 2) { | |
1054 | printk(KERN_INFO "%s: Hamachi Autonegotiation status %4.4x, LPA " | |
1055 | "%4.4x.\n", dev->name, readw(ioaddr + ANStatus), | |
1056 | readw(ioaddr + ANLinkPartnerAbility)); | |
1057 | printk(KERN_INFO "%s: Autonegotiation regs %4.4x %4.4x %4.4x " | |
1058 | "%4.4x %4.4x %4.4x.\n", dev->name, | |
1059 | readw(ioaddr + 0x0e0), | |
1060 | readw(ioaddr + 0x0e2), | |
1061 | readw(ioaddr + 0x0e4), | |
1062 | readw(ioaddr + 0x0e6), | |
1063 | readw(ioaddr + 0x0e8), | |
1064 | readw(ioaddr + 0x0eA)); | |
1065 | } | |
1066 | /* We could do something here... nah. */ | |
1067 | hmp->timer.expires = RUN_AT(next_tick); | |
1068 | add_timer(&hmp->timer); | |
1069 | } | |
1070 | ||
1071 | static void hamachi_tx_timeout(struct net_device *dev) | |
1072 | { | |
1073 | int i; | |
1074 | struct hamachi_private *hmp = netdev_priv(dev); | |
1075 | void __iomem *ioaddr = hmp->base; | |
1076 | ||
1077 | printk(KERN_WARNING "%s: Hamachi transmit timed out, status %8.8x," | |
1078 | " resetting...\n", dev->name, (int)readw(ioaddr + TxStatus)); | |
1079 | ||
1080 | { | |
1081 | int i; | |
1082 | printk(KERN_DEBUG " Rx ring %p: ", hmp->rx_ring); | |
1083 | for (i = 0; i < RX_RING_SIZE; i++) | |
1084 | printk(" %8.8x", (unsigned int)hmp->rx_ring[i].status_n_length); | |
1085 | printk("\n"KERN_DEBUG" Tx ring %p: ", hmp->tx_ring); | |
1086 | for (i = 0; i < TX_RING_SIZE; i++) | |
1087 | printk(" %4.4x", hmp->tx_ring[i].status_n_length); | |
1088 | printk("\n"); | |
1089 | } | |
1090 | ||
1091 | /* Reinit the hardware and make sure the Rx and Tx processes | |
1092 | are up and running. | |
1093 | */ | |
1094 | dev->if_port = 0; | |
1095 | /* The right way to do Reset. -KDU | |
1096 | * -Clear OWN bit in all Rx/Tx descriptors | |
1097 | * -Wait 50 uS for channels to go idle | |
1098 | * -Turn off MAC receiver | |
1099 | * -Issue Reset | |
1100 | */ | |
1101 | ||
1102 | for (i = 0; i < RX_RING_SIZE; i++) | |
1103 | hmp->rx_ring[i].status_n_length &= cpu_to_le32(~DescOwn); | |
1104 | ||
1105 | /* Presume that all packets in the Tx queue are gone if we have to | |
1106 | * re-init the hardware. | |
1107 | */ | |
1108 | for (i = 0; i < TX_RING_SIZE; i++){ | |
1109 | struct sk_buff *skb; | |
1110 | ||
1111 | if (i >= TX_RING_SIZE - 1) | |
1112 | hmp->tx_ring[i].status_n_length = cpu_to_le32( | |
1113 | DescEndRing | | |
1114 | (hmp->tx_ring[i].status_n_length & 0x0000FFFF)); | |
1115 | else | |
1116 | hmp->tx_ring[i].status_n_length &= 0x0000ffff; | |
1117 | skb = hmp->tx_skbuff[i]; | |
1118 | if (skb){ | |
1119 | pci_unmap_single(hmp->pci_dev, hmp->tx_ring[i].addr, | |
1120 | skb->len, PCI_DMA_TODEVICE); | |
1121 | dev_kfree_skb(skb); | |
1122 | hmp->tx_skbuff[i] = NULL; | |
1123 | } | |
1124 | } | |
1125 | ||
1126 | udelay(60); /* Sleep 60 us just for safety sake */ | |
1127 | writew(0x0002, ioaddr + RxCmd); /* STOP Rx */ | |
1128 | ||
1129 | writeb(0x01, ioaddr + ChipReset); /* Reinit the hardware */ | |
1130 | ||
1131 | hmp->tx_full = 0; | |
1132 | hmp->cur_rx = hmp->cur_tx = 0; | |
1133 | hmp->dirty_rx = hmp->dirty_tx = 0; | |
1134 | /* Rx packets are also presumed lost; however, we need to make sure a | |
1135 | * ring of buffers is in tact. -KDU | |
1136 | */ | |
1137 | for (i = 0; i < RX_RING_SIZE; i++){ | |
1138 | struct sk_buff *skb = hmp->rx_skbuff[i]; | |
1139 | ||
1140 | if (skb){ | |
1141 | pci_unmap_single(hmp->pci_dev, hmp->rx_ring[i].addr, | |
1142 | hmp->rx_buf_sz, PCI_DMA_FROMDEVICE); | |
1143 | dev_kfree_skb(skb); | |
1144 | hmp->rx_skbuff[i] = NULL; | |
1145 | } | |
1146 | } | |
1147 | /* Fill in the Rx buffers. Handle allocation failure gracefully. */ | |
1148 | for (i = 0; i < RX_RING_SIZE; i++) { | |
1149 | struct sk_buff *skb = dev_alloc_skb(hmp->rx_buf_sz); | |
1150 | hmp->rx_skbuff[i] = skb; | |
1151 | if (skb == NULL) | |
1152 | break; | |
1153 | skb->dev = dev; /* Mark as being used by this device. */ | |
1154 | skb_reserve(skb, 2); /* 16 byte align the IP header. */ | |
1155 | hmp->rx_ring[i].addr = cpu_to_leXX(pci_map_single(hmp->pci_dev, | |
689be439 | 1156 | skb->data, hmp->rx_buf_sz, PCI_DMA_FROMDEVICE)); |
1da177e4 LT |
1157 | hmp->rx_ring[i].status_n_length = cpu_to_le32(DescOwn | |
1158 | DescEndPacket | DescIntr | (hmp->rx_buf_sz - 2)); | |
1159 | } | |
1160 | hmp->dirty_rx = (unsigned int)(i - RX_RING_SIZE); | |
1161 | /* Mark the last entry as wrapping the ring. */ | |
1162 | hmp->rx_ring[RX_RING_SIZE-1].status_n_length |= cpu_to_le32(DescEndRing); | |
1163 | ||
1164 | /* Trigger an immediate transmit demand. */ | |
1165 | dev->trans_start = jiffies; | |
1166 | hmp->stats.tx_errors++; | |
1167 | ||
1168 | /* Restart the chip's Tx/Rx processes . */ | |
1169 | writew(0x0002, ioaddr + TxCmd); /* STOP Tx */ | |
1170 | writew(0x0001, ioaddr + TxCmd); /* START Tx */ | |
1171 | writew(0x0001, ioaddr + RxCmd); /* START Rx */ | |
1172 | ||
1173 | netif_wake_queue(dev); | |
1174 | } | |
1175 | ||
1176 | ||
1177 | /* Initialize the Rx and Tx rings, along with various 'dev' bits. */ | |
1178 | static void hamachi_init_ring(struct net_device *dev) | |
1179 | { | |
1180 | struct hamachi_private *hmp = netdev_priv(dev); | |
1181 | int i; | |
1182 | ||
1183 | hmp->tx_full = 0; | |
1184 | hmp->cur_rx = hmp->cur_tx = 0; | |
1185 | hmp->dirty_rx = hmp->dirty_tx = 0; | |
1186 | ||
1187 | #if 0 | |
1188 | /* This is wrong. I'm not sure what the original plan was, but this | |
1189 | * is wrong. An MTU of 1 gets you a buffer of 1536, while an MTU | |
1190 | * of 1501 gets a buffer of 1533? -KDU | |
1191 | */ | |
1192 | hmp->rx_buf_sz = (dev->mtu <= 1500 ? PKT_BUF_SZ : dev->mtu + 32); | |
1193 | #endif | |
1194 | /* My attempt at a reasonable correction */ | |
1195 | /* +26 gets the maximum ethernet encapsulation, +7 & ~7 because the | |
1196 | * card needs room to do 8 byte alignment, +2 so we can reserve | |
1197 | * the first 2 bytes, and +16 gets room for the status word from the | |
1198 | * card. -KDU | |
1199 | */ | |
1200 | hmp->rx_buf_sz = (dev->mtu <= 1492 ? PKT_BUF_SZ : | |
1201 | (((dev->mtu+26+7) & ~7) + 2 + 16)); | |
1202 | ||
1203 | /* Initialize all Rx descriptors. */ | |
1204 | for (i = 0; i < RX_RING_SIZE; i++) { | |
1205 | hmp->rx_ring[i].status_n_length = 0; | |
1206 | hmp->rx_skbuff[i] = NULL; | |
1207 | } | |
1208 | /* Fill in the Rx buffers. Handle allocation failure gracefully. */ | |
1209 | for (i = 0; i < RX_RING_SIZE; i++) { | |
1210 | struct sk_buff *skb = dev_alloc_skb(hmp->rx_buf_sz); | |
1211 | hmp->rx_skbuff[i] = skb; | |
1212 | if (skb == NULL) | |
1213 | break; | |
1214 | skb->dev = dev; /* Mark as being used by this device. */ | |
1215 | skb_reserve(skb, 2); /* 16 byte align the IP header. */ | |
1216 | hmp->rx_ring[i].addr = cpu_to_leXX(pci_map_single(hmp->pci_dev, | |
689be439 | 1217 | skb->data, hmp->rx_buf_sz, PCI_DMA_FROMDEVICE)); |
1da177e4 LT |
1218 | /* -2 because it doesn't REALLY have that first 2 bytes -KDU */ |
1219 | hmp->rx_ring[i].status_n_length = cpu_to_le32(DescOwn | | |
1220 | DescEndPacket | DescIntr | (hmp->rx_buf_sz -2)); | |
1221 | } | |
1222 | hmp->dirty_rx = (unsigned int)(i - RX_RING_SIZE); | |
1223 | hmp->rx_ring[RX_RING_SIZE-1].status_n_length |= cpu_to_le32(DescEndRing); | |
1224 | ||
1225 | for (i = 0; i < TX_RING_SIZE; i++) { | |
1226 | hmp->tx_skbuff[i] = NULL; | |
1227 | hmp->tx_ring[i].status_n_length = 0; | |
1228 | } | |
1229 | /* Mark the last entry of the ring */ | |
1230 | hmp->tx_ring[TX_RING_SIZE-1].status_n_length |= cpu_to_le32(DescEndRing); | |
1231 | ||
1232 | return; | |
1233 | } | |
1234 | ||
1235 | ||
1236 | #ifdef TX_CHECKSUM | |
1237 | #define csum_add(it, val) \ | |
1238 | do { \ | |
1239 | it += (u16) (val); \ | |
1240 | if (it & 0xffff0000) { \ | |
1241 | it &= 0xffff; \ | |
1242 | ++it; \ | |
1243 | } \ | |
1244 | } while (0) | |
1245 | /* printk("add %04x --> %04x\n", val, it); \ */ | |
1246 | ||
1247 | /* uh->len already network format, do not swap */ | |
1248 | #define pseudo_csum_udp(sum,ih,uh) do { \ | |
1249 | sum = 0; \ | |
1250 | csum_add(sum, (ih)->saddr >> 16); \ | |
1251 | csum_add(sum, (ih)->saddr & 0xffff); \ | |
1252 | csum_add(sum, (ih)->daddr >> 16); \ | |
1253 | csum_add(sum, (ih)->daddr & 0xffff); \ | |
1254 | csum_add(sum, __constant_htons(IPPROTO_UDP)); \ | |
1255 | csum_add(sum, (uh)->len); \ | |
1256 | } while (0) | |
1257 | ||
1258 | /* swap len */ | |
1259 | #define pseudo_csum_tcp(sum,ih,len) do { \ | |
1260 | sum = 0; \ | |
1261 | csum_add(sum, (ih)->saddr >> 16); \ | |
1262 | csum_add(sum, (ih)->saddr & 0xffff); \ | |
1263 | csum_add(sum, (ih)->daddr >> 16); \ | |
1264 | csum_add(sum, (ih)->daddr & 0xffff); \ | |
1265 | csum_add(sum, __constant_htons(IPPROTO_TCP)); \ | |
1266 | csum_add(sum, htons(len)); \ | |
1267 | } while (0) | |
1268 | #endif | |
1269 | ||
1270 | static int hamachi_start_xmit(struct sk_buff *skb, struct net_device *dev) | |
1271 | { | |
1272 | struct hamachi_private *hmp = netdev_priv(dev); | |
1273 | unsigned entry; | |
1274 | u16 status; | |
1275 | ||
1276 | /* Ok, now make sure that the queue has space before trying to | |
1277 | add another skbuff. if we return non-zero the scheduler | |
1278 | should interpret this as a queue full and requeue the buffer | |
1279 | for later. | |
1280 | */ | |
1281 | if (hmp->tx_full) { | |
1282 | /* We should NEVER reach this point -KDU */ | |
1283 | printk(KERN_WARNING "%s: Hamachi transmit queue full at slot %d.\n",dev->name, hmp->cur_tx); | |
1284 | ||
1285 | /* Wake the potentially-idle transmit channel. */ | |
1286 | /* If we don't need to read status, DON'T -KDU */ | |
1287 | status=readw(hmp->base + TxStatus); | |
1288 | if( !(status & 0x0001) || (status & 0x0002)) | |
1289 | writew(0x0001, hmp->base + TxCmd); | |
1290 | return 1; | |
1291 | } | |
1292 | ||
1293 | /* Caution: the write order is important here, set the field | |
1294 | with the "ownership" bits last. */ | |
1295 | ||
1296 | /* Calculate the next Tx descriptor entry. */ | |
1297 | entry = hmp->cur_tx % TX_RING_SIZE; | |
1298 | ||
1299 | hmp->tx_skbuff[entry] = skb; | |
1300 | ||
1301 | #ifdef TX_CHECKSUM | |
1302 | { | |
1303 | /* tack on checksum tag */ | |
1304 | u32 tagval = 0; | |
1305 | struct ethhdr *eh = (struct ethhdr *)skb->data; | |
1306 | if (eh->h_proto == __constant_htons(ETH_P_IP)) { | |
1307 | struct iphdr *ih = (struct iphdr *)((char *)eh + ETH_HLEN); | |
1308 | if (ih->protocol == IPPROTO_UDP) { | |
1309 | struct udphdr *uh | |
1310 | = (struct udphdr *)((char *)ih + ih->ihl*4); | |
1311 | u32 offset = ((unsigned char *)uh + 6) - skb->data; | |
1312 | u32 pseudo; | |
1313 | pseudo_csum_udp(pseudo, ih, uh); | |
1314 | pseudo = htons(pseudo); | |
1315 | printk("udp cksum was %04x, sending pseudo %04x\n", | |
1316 | uh->check, pseudo); | |
1317 | uh->check = 0; /* zero out uh->check before card calc */ | |
1318 | /* | |
1319 | * start at 14 (skip ethhdr), store at offset (uh->check), | |
1320 | * use pseudo value given. | |
1321 | */ | |
1322 | tagval = (14 << 24) | (offset << 16) | pseudo; | |
1323 | } else if (ih->protocol == IPPROTO_TCP) { | |
1324 | printk("tcp, no auto cksum\n"); | |
1325 | } | |
1326 | } | |
1327 | *(u32 *)skb_push(skb, 8) = tagval; | |
1328 | } | |
1329 | #endif | |
1330 | ||
1331 | hmp->tx_ring[entry].addr = cpu_to_leXX(pci_map_single(hmp->pci_dev, | |
1332 | skb->data, skb->len, PCI_DMA_TODEVICE)); | |
1333 | ||
1334 | /* Hmmmm, could probably put a DescIntr on these, but the way | |
1335 | the driver is currently coded makes Tx interrupts unnecessary | |
1336 | since the clearing of the Tx ring is handled by the start_xmit | |
1337 | routine. This organization helps mitigate the interrupts a | |
1338 | bit and probably renders the max_tx_latency param useless. | |
1339 | ||
1340 | Update: Putting a DescIntr bit on all of the descriptors and | |
1341 | mitigating interrupt frequency with the tx_min_pkt parameter. -KDU | |
1342 | */ | |
1343 | if (entry >= TX_RING_SIZE-1) /* Wrap ring */ | |
1344 | hmp->tx_ring[entry].status_n_length = cpu_to_le32(DescOwn | | |
1345 | DescEndPacket | DescEndRing | DescIntr | skb->len); | |
1346 | else | |
1347 | hmp->tx_ring[entry].status_n_length = cpu_to_le32(DescOwn | | |
1348 | DescEndPacket | DescIntr | skb->len); | |
1349 | hmp->cur_tx++; | |
1350 | ||
1351 | /* Non-x86 Todo: explicitly flush cache lines here. */ | |
1352 | ||
1353 | /* Wake the potentially-idle transmit channel. */ | |
1354 | /* If we don't need to read status, DON'T -KDU */ | |
1355 | status=readw(hmp->base + TxStatus); | |
1356 | if( !(status & 0x0001) || (status & 0x0002)) | |
1357 | writew(0x0001, hmp->base + TxCmd); | |
1358 | ||
1359 | /* Immediately before returning, let's clear as many entries as we can. */ | |
1360 | hamachi_tx(dev); | |
1361 | ||
1362 | /* We should kick the bottom half here, since we are not accepting | |
1363 | * interrupts with every packet. i.e. realize that Gigabit ethernet | |
1364 | * can transmit faster than ordinary machines can load packets; | |
1365 | * hence, any packet that got put off because we were in the transmit | |
1366 | * routine should IMMEDIATELY get a chance to be re-queued. -KDU | |
1367 | */ | |
1368 | if ((hmp->cur_tx - hmp->dirty_tx) < (TX_RING_SIZE - 4)) | |
1369 | netif_wake_queue(dev); /* Typical path */ | |
1370 | else { | |
1371 | hmp->tx_full = 1; | |
1372 | netif_stop_queue(dev); | |
1373 | } | |
1374 | dev->trans_start = jiffies; | |
1375 | ||
1376 | if (hamachi_debug > 4) { | |
1377 | printk(KERN_DEBUG "%s: Hamachi transmit frame #%d queued in slot %d.\n", | |
1378 | dev->name, hmp->cur_tx, entry); | |
1379 | } | |
1380 | return 0; | |
1381 | } | |
1382 | ||
1383 | /* The interrupt handler does all of the Rx thread work and cleans up | |
1384 | after the Tx thread. */ | |
1385 | static irqreturn_t hamachi_interrupt(int irq, void *dev_instance, struct pt_regs *rgs) | |
1386 | { | |
1387 | struct net_device *dev = dev_instance; | |
1388 | struct hamachi_private *hmp = netdev_priv(dev); | |
1389 | void __iomem *ioaddr = hmp->base; | |
1390 | long boguscnt = max_interrupt_work; | |
1391 | int handled = 0; | |
1392 | ||
1393 | #ifndef final_version /* Can never occur. */ | |
1394 | if (dev == NULL) { | |
1395 | printk (KERN_ERR "hamachi_interrupt(): irq %d for unknown device.\n", irq); | |
1396 | return IRQ_NONE; | |
1397 | } | |
1398 | #endif | |
1399 | ||
1400 | spin_lock(&hmp->lock); | |
1401 | ||
1402 | do { | |
1403 | u32 intr_status = readl(ioaddr + InterruptClear); | |
1404 | ||
1405 | if (hamachi_debug > 4) | |
1406 | printk(KERN_DEBUG "%s: Hamachi interrupt, status %4.4x.\n", | |
1407 | dev->name, intr_status); | |
1408 | ||
1409 | if (intr_status == 0) | |
1410 | break; | |
1411 | ||
1412 | handled = 1; | |
1413 | ||
1414 | if (intr_status & IntrRxDone) | |
1415 | hamachi_rx(dev); | |
1416 | ||
1417 | if (intr_status & IntrTxDone){ | |
1418 | /* This code should RARELY need to execute. After all, this is | |
1419 | * a gigabit link, it should consume packets as fast as we put | |
1420 | * them in AND we clear the Tx ring in hamachi_start_xmit(). | |
1421 | */ | |
1422 | if (hmp->tx_full){ | |
1423 | for (; hmp->cur_tx - hmp->dirty_tx > 0; hmp->dirty_tx++){ | |
1424 | int entry = hmp->dirty_tx % TX_RING_SIZE; | |
1425 | struct sk_buff *skb; | |
1426 | ||
1427 | if (hmp->tx_ring[entry].status_n_length & cpu_to_le32(DescOwn)) | |
1428 | break; | |
1429 | skb = hmp->tx_skbuff[entry]; | |
1430 | /* Free the original skb. */ | |
1431 | if (skb){ | |
1432 | pci_unmap_single(hmp->pci_dev, | |
1433 | hmp->tx_ring[entry].addr, | |
1434 | skb->len, | |
1435 | PCI_DMA_TODEVICE); | |
1436 | dev_kfree_skb_irq(skb); | |
1437 | hmp->tx_skbuff[entry] = NULL; | |
1438 | } | |
1439 | hmp->tx_ring[entry].status_n_length = 0; | |
1440 | if (entry >= TX_RING_SIZE-1) | |
1441 | hmp->tx_ring[TX_RING_SIZE-1].status_n_length |= | |
1442 | cpu_to_le32(DescEndRing); | |
1443 | hmp->stats.tx_packets++; | |
1444 | } | |
1445 | if (hmp->cur_tx - hmp->dirty_tx < TX_RING_SIZE - 4){ | |
1446 | /* The ring is no longer full */ | |
1447 | hmp->tx_full = 0; | |
1448 | netif_wake_queue(dev); | |
1449 | } | |
1450 | } else { | |
1451 | netif_wake_queue(dev); | |
1452 | } | |
1453 | } | |
1454 | ||
1455 | ||
1456 | /* Abnormal error summary/uncommon events handlers. */ | |
1457 | if (intr_status & | |
1458 | (IntrTxPCIFault | IntrTxPCIErr | IntrRxPCIFault | IntrRxPCIErr | | |
1459 | LinkChange | NegotiationChange | StatsMax)) | |
1460 | hamachi_error(dev, intr_status); | |
1461 | ||
1462 | if (--boguscnt < 0) { | |
1463 | printk(KERN_WARNING "%s: Too much work at interrupt, status=0x%4.4x.\n", | |
1464 | dev->name, intr_status); | |
1465 | break; | |
1466 | } | |
1467 | } while (1); | |
1468 | ||
1469 | if (hamachi_debug > 3) | |
1470 | printk(KERN_DEBUG "%s: exiting interrupt, status=%#4.4x.\n", | |
1471 | dev->name, readl(ioaddr + IntrStatus)); | |
1472 | ||
1473 | #ifndef final_version | |
1474 | /* Code that should never be run! Perhaps remove after testing.. */ | |
1475 | { | |
1476 | static int stopit = 10; | |
1477 | if (dev->start == 0 && --stopit < 0) { | |
1478 | printk(KERN_ERR "%s: Emergency stop, looping startup interrupt.\n", | |
1479 | dev->name); | |
1480 | free_irq(irq, dev); | |
1481 | } | |
1482 | } | |
1483 | #endif | |
1484 | ||
1485 | spin_unlock(&hmp->lock); | |
1486 | return IRQ_RETVAL(handled); | |
1487 | } | |
1488 | ||
1489 | /* This routine is logically part of the interrupt handler, but separated | |
1490 | for clarity and better register allocation. */ | |
1491 | static int hamachi_rx(struct net_device *dev) | |
1492 | { | |
1493 | struct hamachi_private *hmp = netdev_priv(dev); | |
1494 | int entry = hmp->cur_rx % RX_RING_SIZE; | |
1495 | int boguscnt = (hmp->dirty_rx + RX_RING_SIZE) - hmp->cur_rx; | |
1496 | ||
1497 | if (hamachi_debug > 4) { | |
1498 | printk(KERN_DEBUG " In hamachi_rx(), entry %d status %4.4x.\n", | |
1499 | entry, hmp->rx_ring[entry].status_n_length); | |
1500 | } | |
1501 | ||
1502 | /* If EOP is set on the next entry, it's a new packet. Send it up. */ | |
1503 | while (1) { | |
1504 | struct hamachi_desc *desc = &(hmp->rx_ring[entry]); | |
1505 | u32 desc_status = le32_to_cpu(desc->status_n_length); | |
1506 | u16 data_size = desc_status; /* Implicit truncate */ | |
1507 | u8 *buf_addr; | |
1508 | s32 frame_status; | |
1509 | ||
1510 | if (desc_status & DescOwn) | |
1511 | break; | |
1512 | pci_dma_sync_single_for_cpu(hmp->pci_dev, | |
1513 | desc->addr, | |
1514 | hmp->rx_buf_sz, | |
1515 | PCI_DMA_FROMDEVICE); | |
689be439 | 1516 | buf_addr = (u8 *) hmp->rx_skbuff[entry]->data; |
1da177e4 LT |
1517 | frame_status = le32_to_cpu(get_unaligned((s32*)&(buf_addr[data_size - 12]))); |
1518 | if (hamachi_debug > 4) | |
1519 | printk(KERN_DEBUG " hamachi_rx() status was %8.8x.\n", | |
1520 | frame_status); | |
1521 | if (--boguscnt < 0) | |
1522 | break; | |
1523 | if ( ! (desc_status & DescEndPacket)) { | |
1524 | printk(KERN_WARNING "%s: Oversized Ethernet frame spanned " | |
1525 | "multiple buffers, entry %#x length %d status %4.4x!\n", | |
1526 | dev->name, hmp->cur_rx, data_size, desc_status); | |
1527 | printk(KERN_WARNING "%s: Oversized Ethernet frame %p vs %p.\n", | |
1528 | dev->name, desc, &hmp->rx_ring[hmp->cur_rx % RX_RING_SIZE]); | |
1529 | printk(KERN_WARNING "%s: Oversized Ethernet frame -- next status %x/%x last status %x.\n", | |
1530 | dev->name, | |
1531 | hmp->rx_ring[(hmp->cur_rx+1) % RX_RING_SIZE].status_n_length & 0xffff0000, | |
1532 | hmp->rx_ring[(hmp->cur_rx+1) % RX_RING_SIZE].status_n_length & 0x0000ffff, | |
1533 | hmp->rx_ring[(hmp->cur_rx-1) % RX_RING_SIZE].status_n_length); | |
1534 | hmp->stats.rx_length_errors++; | |
1535 | } /* else Omit for prototype errata??? */ | |
1536 | if (frame_status & 0x00380000) { | |
1537 | /* There was an error. */ | |
1538 | if (hamachi_debug > 2) | |
1539 | printk(KERN_DEBUG " hamachi_rx() Rx error was %8.8x.\n", | |
1540 | frame_status); | |
1541 | hmp->stats.rx_errors++; | |
1542 | if (frame_status & 0x00600000) hmp->stats.rx_length_errors++; | |
1543 | if (frame_status & 0x00080000) hmp->stats.rx_frame_errors++; | |
1544 | if (frame_status & 0x00100000) hmp->stats.rx_crc_errors++; | |
1545 | if (frame_status < 0) hmp->stats.rx_dropped++; | |
1546 | } else { | |
1547 | struct sk_buff *skb; | |
1548 | /* Omit CRC */ | |
1549 | u16 pkt_len = (frame_status & 0x07ff) - 4; | |
1550 | #ifdef RX_CHECKSUM | |
1551 | u32 pfck = *(u32 *) &buf_addr[data_size - 8]; | |
1552 | #endif | |
1553 | ||
1554 | ||
1555 | #ifndef final_version | |
1556 | if (hamachi_debug > 4) | |
1557 | printk(KERN_DEBUG " hamachi_rx() normal Rx pkt length %d" | |
1558 | " of %d, bogus_cnt %d.\n", | |
1559 | pkt_len, data_size, boguscnt); | |
1560 | if (hamachi_debug > 5) | |
1561 | printk(KERN_DEBUG"%s: rx status %8.8x %8.8x %8.8x %8.8x %8.8x.\n", | |
1562 | dev->name, | |
1563 | *(s32*)&(buf_addr[data_size - 20]), | |
1564 | *(s32*)&(buf_addr[data_size - 16]), | |
1565 | *(s32*)&(buf_addr[data_size - 12]), | |
1566 | *(s32*)&(buf_addr[data_size - 8]), | |
1567 | *(s32*)&(buf_addr[data_size - 4])); | |
1568 | #endif | |
1569 | /* Check if the packet is long enough to accept without copying | |
1570 | to a minimally-sized skbuff. */ | |
1571 | if (pkt_len < rx_copybreak | |
1572 | && (skb = dev_alloc_skb(pkt_len + 2)) != NULL) { | |
1573 | #ifdef RX_CHECKSUM | |
1574 | printk(KERN_ERR "%s: rx_copybreak non-zero " | |
1575 | "not good with RX_CHECKSUM\n", dev->name); | |
1576 | #endif | |
1577 | skb->dev = dev; | |
1578 | skb_reserve(skb, 2); /* 16 byte align the IP header */ | |
1579 | pci_dma_sync_single_for_cpu(hmp->pci_dev, | |
1580 | hmp->rx_ring[entry].addr, | |
1581 | hmp->rx_buf_sz, | |
1582 | PCI_DMA_FROMDEVICE); | |
1583 | /* Call copy + cksum if available. */ | |
1584 | #if 1 || USE_IP_COPYSUM | |
1585 | eth_copy_and_sum(skb, | |
1586 | hmp->rx_skbuff[entry]->data, pkt_len, 0); | |
1587 | skb_put(skb, pkt_len); | |
1588 | #else | |
1589 | memcpy(skb_put(skb, pkt_len), hmp->rx_ring_dma | |
1590 | + entry*sizeof(*desc), pkt_len); | |
1591 | #endif | |
1592 | pci_dma_sync_single_for_device(hmp->pci_dev, | |
1593 | hmp->rx_ring[entry].addr, | |
1594 | hmp->rx_buf_sz, | |
1595 | PCI_DMA_FROMDEVICE); | |
1596 | } else { | |
1597 | pci_unmap_single(hmp->pci_dev, | |
1598 | hmp->rx_ring[entry].addr, | |
1599 | hmp->rx_buf_sz, PCI_DMA_FROMDEVICE); | |
1600 | skb_put(skb = hmp->rx_skbuff[entry], pkt_len); | |
1601 | hmp->rx_skbuff[entry] = NULL; | |
1602 | } | |
1603 | skb->protocol = eth_type_trans(skb, dev); | |
1604 | ||
1605 | ||
1606 | #ifdef RX_CHECKSUM | |
1607 | /* TCP or UDP on ipv4, DIX encoding */ | |
1608 | if (pfck>>24 == 0x91 || pfck>>24 == 0x51) { | |
1609 | struct iphdr *ih = (struct iphdr *) skb->data; | |
1610 | /* Check that IP packet is at least 46 bytes, otherwise, | |
1611 | * there may be pad bytes included in the hardware checksum. | |
1612 | * This wouldn't happen if everyone padded with 0. | |
1613 | */ | |
1614 | if (ntohs(ih->tot_len) >= 46){ | |
1615 | /* don't worry about frags */ | |
1616 | if (!(ih->frag_off & __constant_htons(IP_MF|IP_OFFSET))) { | |
1617 | u32 inv = *(u32 *) &buf_addr[data_size - 16]; | |
1618 | u32 *p = (u32 *) &buf_addr[data_size - 20]; | |
1619 | register u32 crc, p_r, p_r1; | |
1620 | ||
1621 | if (inv & 4) { | |
1622 | inv &= ~4; | |
1623 | --p; | |
1624 | } | |
1625 | p_r = *p; | |
1626 | p_r1 = *(p-1); | |
1627 | switch (inv) { | |
1628 | case 0: | |
1629 | crc = (p_r & 0xffff) + (p_r >> 16); | |
1630 | break; | |
1631 | case 1: | |
1632 | crc = (p_r >> 16) + (p_r & 0xffff) | |
1633 | + (p_r1 >> 16 & 0xff00); | |
1634 | break; | |
1635 | case 2: | |
1636 | crc = p_r + (p_r1 >> 16); | |
1637 | break; | |
1638 | case 3: | |
1639 | crc = p_r + (p_r1 & 0xff00) + (p_r1 >> 16); | |
1640 | break; | |
1641 | default: /*NOTREACHED*/ crc = 0; | |
1642 | } | |
1643 | if (crc & 0xffff0000) { | |
1644 | crc &= 0xffff; | |
1645 | ++crc; | |
1646 | } | |
1647 | /* tcp/udp will add in pseudo */ | |
1648 | skb->csum = ntohs(pfck & 0xffff); | |
1649 | if (skb->csum > crc) | |
1650 | skb->csum -= crc; | |
1651 | else | |
1652 | skb->csum += (~crc & 0xffff); | |
1653 | /* | |
1654 | * could do the pseudo myself and return | |
1655 | * CHECKSUM_UNNECESSARY | |
1656 | */ | |
1657 | skb->ip_summed = CHECKSUM_HW; | |
1658 | } | |
1659 | } | |
1660 | } | |
1661 | #endif /* RX_CHECKSUM */ | |
1662 | ||
1663 | netif_rx(skb); | |
1664 | dev->last_rx = jiffies; | |
1665 | hmp->stats.rx_packets++; | |
1666 | } | |
1667 | entry = (++hmp->cur_rx) % RX_RING_SIZE; | |
1668 | } | |
1669 | ||
1670 | /* Refill the Rx ring buffers. */ | |
1671 | for (; hmp->cur_rx - hmp->dirty_rx > 0; hmp->dirty_rx++) { | |
1672 | struct hamachi_desc *desc; | |
1673 | ||
1674 | entry = hmp->dirty_rx % RX_RING_SIZE; | |
1675 | desc = &(hmp->rx_ring[entry]); | |
1676 | if (hmp->rx_skbuff[entry] == NULL) { | |
1677 | struct sk_buff *skb = dev_alloc_skb(hmp->rx_buf_sz); | |
1678 | ||
1679 | hmp->rx_skbuff[entry] = skb; | |
1680 | if (skb == NULL) | |
1681 | break; /* Better luck next round. */ | |
1682 | skb->dev = dev; /* Mark as being used by this device. */ | |
1683 | skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */ | |
1684 | desc->addr = cpu_to_leXX(pci_map_single(hmp->pci_dev, | |
689be439 | 1685 | skb->data, hmp->rx_buf_sz, PCI_DMA_FROMDEVICE)); |
1da177e4 LT |
1686 | } |
1687 | desc->status_n_length = cpu_to_le32(hmp->rx_buf_sz); | |
1688 | if (entry >= RX_RING_SIZE-1) | |
1689 | desc->status_n_length |= cpu_to_le32(DescOwn | | |
1690 | DescEndPacket | DescEndRing | DescIntr); | |
1691 | else | |
1692 | desc->status_n_length |= cpu_to_le32(DescOwn | | |
1693 | DescEndPacket | DescIntr); | |
1694 | } | |
1695 | ||
1696 | /* Restart Rx engine if stopped. */ | |
1697 | /* If we don't need to check status, don't. -KDU */ | |
1698 | if (readw(hmp->base + RxStatus) & 0x0002) | |
1699 | writew(0x0001, hmp->base + RxCmd); | |
1700 | ||
1701 | return 0; | |
1702 | } | |
1703 | ||
1704 | /* This is more properly named "uncommon interrupt events", as it covers more | |
1705 | than just errors. */ | |
1706 | static void hamachi_error(struct net_device *dev, int intr_status) | |
1707 | { | |
1708 | struct hamachi_private *hmp = netdev_priv(dev); | |
1709 | void __iomem *ioaddr = hmp->base; | |
1710 | ||
1711 | if (intr_status & (LinkChange|NegotiationChange)) { | |
1712 | if (hamachi_debug > 1) | |
1713 | printk(KERN_INFO "%s: Link changed: AutoNegotiation Ctrl" | |
1714 | " %4.4x, Status %4.4x %4.4x Intr status %4.4x.\n", | |
1715 | dev->name, readw(ioaddr + 0x0E0), readw(ioaddr + 0x0E2), | |
1716 | readw(ioaddr + ANLinkPartnerAbility), | |
1717 | readl(ioaddr + IntrStatus)); | |
1718 | if (readw(ioaddr + ANStatus) & 0x20) | |
1719 | writeb(0x01, ioaddr + LEDCtrl); | |
1720 | else | |
1721 | writeb(0x03, ioaddr + LEDCtrl); | |
1722 | } | |
1723 | if (intr_status & StatsMax) { | |
1724 | hamachi_get_stats(dev); | |
1725 | /* Read the overflow bits to clear. */ | |
1726 | readl(ioaddr + 0x370); | |
1727 | readl(ioaddr + 0x3F0); | |
1728 | } | |
1729 | if ((intr_status & ~(LinkChange|StatsMax|NegotiationChange|IntrRxDone|IntrTxDone)) | |
1730 | && hamachi_debug) | |
1731 | printk(KERN_ERR "%s: Something Wicked happened! %4.4x.\n", | |
1732 | dev->name, intr_status); | |
1733 | /* Hmmmmm, it's not clear how to recover from PCI faults. */ | |
1734 | if (intr_status & (IntrTxPCIErr | IntrTxPCIFault)) | |
1735 | hmp->stats.tx_fifo_errors++; | |
1736 | if (intr_status & (IntrRxPCIErr | IntrRxPCIFault)) | |
1737 | hmp->stats.rx_fifo_errors++; | |
1738 | } | |
1739 | ||
1740 | static int hamachi_close(struct net_device *dev) | |
1741 | { | |
1742 | struct hamachi_private *hmp = netdev_priv(dev); | |
1743 | void __iomem *ioaddr = hmp->base; | |
1744 | struct sk_buff *skb; | |
1745 | int i; | |
1746 | ||
1747 | netif_stop_queue(dev); | |
1748 | ||
1749 | if (hamachi_debug > 1) { | |
1750 | printk(KERN_DEBUG "%s: Shutting down ethercard, status was Tx %4.4x Rx %4.4x Int %2.2x.\n", | |
1751 | dev->name, readw(ioaddr + TxStatus), | |
1752 | readw(ioaddr + RxStatus), readl(ioaddr + IntrStatus)); | |
1753 | printk(KERN_DEBUG "%s: Queue pointers were Tx %d / %d, Rx %d / %d.\n", | |
1754 | dev->name, hmp->cur_tx, hmp->dirty_tx, hmp->cur_rx, hmp->dirty_rx); | |
1755 | } | |
1756 | ||
1757 | /* Disable interrupts by clearing the interrupt mask. */ | |
1758 | writel(0x0000, ioaddr + InterruptEnable); | |
1759 | ||
1760 | /* Stop the chip's Tx and Rx processes. */ | |
1761 | writel(2, ioaddr + RxCmd); | |
1762 | writew(2, ioaddr + TxCmd); | |
1763 | ||
1764 | #ifdef __i386__ | |
1765 | if (hamachi_debug > 2) { | |
1766 | printk("\n"KERN_DEBUG" Tx ring at %8.8x:\n", | |
1767 | (int)hmp->tx_ring_dma); | |
1768 | for (i = 0; i < TX_RING_SIZE; i++) | |
1769 | printk(" %c #%d desc. %8.8x %8.8x.\n", | |
1770 | readl(ioaddr + TxCurPtr) == (long)&hmp->tx_ring[i] ? '>' : ' ', | |
1771 | i, hmp->tx_ring[i].status_n_length, hmp->tx_ring[i].addr); | |
1772 | printk("\n"KERN_DEBUG " Rx ring %8.8x:\n", | |
1773 | (int)hmp->rx_ring_dma); | |
1774 | for (i = 0; i < RX_RING_SIZE; i++) { | |
1775 | printk(KERN_DEBUG " %c #%d desc. %4.4x %8.8x\n", | |
1776 | readl(ioaddr + RxCurPtr) == (long)&hmp->rx_ring[i] ? '>' : ' ', | |
1777 | i, hmp->rx_ring[i].status_n_length, hmp->rx_ring[i].addr); | |
1778 | if (hamachi_debug > 6) { | |
689be439 | 1779 | if (*(u8*)hmp->rx_skbuff[i]->data != 0x69) { |
1da177e4 | 1780 | u16 *addr = (u16 *) |
689be439 | 1781 | hmp->rx_skbuff[i]->data; |
1da177e4 LT |
1782 | int j; |
1783 | ||
1784 | for (j = 0; j < 0x50; j++) | |
1785 | printk(" %4.4x", addr[j]); | |
1786 | printk("\n"); | |
1787 | } | |
1788 | } | |
1789 | } | |
1790 | } | |
1791 | #endif /* __i386__ debugging only */ | |
1792 | ||
1793 | free_irq(dev->irq, dev); | |
1794 | ||
1795 | del_timer_sync(&hmp->timer); | |
1796 | ||
1797 | /* Free all the skbuffs in the Rx queue. */ | |
1798 | for (i = 0; i < RX_RING_SIZE; i++) { | |
1799 | skb = hmp->rx_skbuff[i]; | |
1800 | hmp->rx_ring[i].status_n_length = 0; | |
1801 | hmp->rx_ring[i].addr = 0xBADF00D0; /* An invalid address. */ | |
1802 | if (skb) { | |
1803 | pci_unmap_single(hmp->pci_dev, | |
1804 | hmp->rx_ring[i].addr, hmp->rx_buf_sz, | |
1805 | PCI_DMA_FROMDEVICE); | |
1806 | dev_kfree_skb(skb); | |
1807 | hmp->rx_skbuff[i] = NULL; | |
1808 | } | |
1809 | } | |
1810 | for (i = 0; i < TX_RING_SIZE; i++) { | |
1811 | skb = hmp->tx_skbuff[i]; | |
1812 | if (skb) { | |
1813 | pci_unmap_single(hmp->pci_dev, | |
1814 | hmp->tx_ring[i].addr, skb->len, | |
1815 | PCI_DMA_TODEVICE); | |
1816 | dev_kfree_skb(skb); | |
1817 | hmp->tx_skbuff[i] = NULL; | |
1818 | } | |
1819 | } | |
1820 | ||
1821 | writeb(0x00, ioaddr + LEDCtrl); | |
1822 | ||
1823 | return 0; | |
1824 | } | |
1825 | ||
1826 | static struct net_device_stats *hamachi_get_stats(struct net_device *dev) | |
1827 | { | |
1828 | struct hamachi_private *hmp = netdev_priv(dev); | |
1829 | void __iomem *ioaddr = hmp->base; | |
1830 | ||
1831 | /* We should lock this segment of code for SMP eventually, although | |
1832 | the vulnerability window is very small and statistics are | |
1833 | non-critical. */ | |
1834 | /* Ok, what goes here? This appears to be stuck at 21 packets | |
1835 | according to ifconfig. It does get incremented in hamachi_tx(), | |
1836 | so I think I'll comment it out here and see if better things | |
1837 | happen. | |
1838 | */ | |
1839 | /* hmp->stats.tx_packets = readl(ioaddr + 0x000); */ | |
1840 | ||
1841 | hmp->stats.rx_bytes = readl(ioaddr + 0x330); /* Total Uni+Brd+Multi */ | |
1842 | hmp->stats.tx_bytes = readl(ioaddr + 0x3B0); /* Total Uni+Brd+Multi */ | |
1843 | hmp->stats.multicast = readl(ioaddr + 0x320); /* Multicast Rx */ | |
1844 | ||
1845 | hmp->stats.rx_length_errors = readl(ioaddr + 0x368); /* Over+Undersized */ | |
1846 | hmp->stats.rx_over_errors = readl(ioaddr + 0x35C); /* Jabber */ | |
1847 | hmp->stats.rx_crc_errors = readl(ioaddr + 0x360); /* Jabber */ | |
1848 | hmp->stats.rx_frame_errors = readl(ioaddr + 0x364); /* Symbol Errs */ | |
1849 | hmp->stats.rx_missed_errors = readl(ioaddr + 0x36C); /* Dropped */ | |
1850 | ||
1851 | return &hmp->stats; | |
1852 | } | |
1853 | ||
1854 | static void set_rx_mode(struct net_device *dev) | |
1855 | { | |
1856 | struct hamachi_private *hmp = netdev_priv(dev); | |
1857 | void __iomem *ioaddr = hmp->base; | |
1858 | ||
1859 | if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */ | |
1860 | /* Unconditionally log net taps. */ | |
1861 | printk(KERN_NOTICE "%s: Promiscuous mode enabled.\n", dev->name); | |
1862 | writew(0x000F, ioaddr + AddrMode); | |
1863 | } else if ((dev->mc_count > 63) || (dev->flags & IFF_ALLMULTI)) { | |
1864 | /* Too many to match, or accept all multicasts. */ | |
1865 | writew(0x000B, ioaddr + AddrMode); | |
1866 | } else if (dev->mc_count > 0) { /* Must use the CAM filter. */ | |
1867 | struct dev_mc_list *mclist; | |
1868 | int i; | |
1869 | for (i = 0, mclist = dev->mc_list; mclist && i < dev->mc_count; | |
1870 | i++, mclist = mclist->next) { | |
1871 | writel(*(u32*)(mclist->dmi_addr), ioaddr + 0x100 + i*8); | |
1872 | writel(0x20000 | (*(u16*)&mclist->dmi_addr[4]), | |
1873 | ioaddr + 0x104 + i*8); | |
1874 | } | |
1875 | /* Clear remaining entries. */ | |
1876 | for (; i < 64; i++) | |
1877 | writel(0, ioaddr + 0x104 + i*8); | |
1878 | writew(0x0003, ioaddr + AddrMode); | |
1879 | } else { /* Normal, unicast/broadcast-only mode. */ | |
1880 | writew(0x0001, ioaddr + AddrMode); | |
1881 | } | |
1882 | } | |
1883 | ||
1884 | static int check_if_running(struct net_device *dev) | |
1885 | { | |
1886 | if (!netif_running(dev)) | |
1887 | return -EINVAL; | |
1888 | return 0; | |
1889 | } | |
1890 | ||
1891 | static void hamachi_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info) | |
1892 | { | |
1893 | struct hamachi_private *np = netdev_priv(dev); | |
1894 | strcpy(info->driver, DRV_NAME); | |
1895 | strcpy(info->version, DRV_VERSION); | |
1896 | strcpy(info->bus_info, pci_name(np->pci_dev)); | |
1897 | } | |
1898 | ||
1899 | static int hamachi_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd) | |
1900 | { | |
1901 | struct hamachi_private *np = netdev_priv(dev); | |
1902 | spin_lock_irq(&np->lock); | |
1903 | mii_ethtool_gset(&np->mii_if, ecmd); | |
1904 | spin_unlock_irq(&np->lock); | |
1905 | return 0; | |
1906 | } | |
1907 | ||
1908 | static int hamachi_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd) | |
1909 | { | |
1910 | struct hamachi_private *np = netdev_priv(dev); | |
1911 | int res; | |
1912 | spin_lock_irq(&np->lock); | |
1913 | res = mii_ethtool_sset(&np->mii_if, ecmd); | |
1914 | spin_unlock_irq(&np->lock); | |
1915 | return res; | |
1916 | } | |
1917 | ||
1918 | static int hamachi_nway_reset(struct net_device *dev) | |
1919 | { | |
1920 | struct hamachi_private *np = netdev_priv(dev); | |
1921 | return mii_nway_restart(&np->mii_if); | |
1922 | } | |
1923 | ||
1924 | static u32 hamachi_get_link(struct net_device *dev) | |
1925 | { | |
1926 | struct hamachi_private *np = netdev_priv(dev); | |
1927 | return mii_link_ok(&np->mii_if); | |
1928 | } | |
1929 | ||
1930 | static struct ethtool_ops ethtool_ops = { | |
1931 | .begin = check_if_running, | |
1932 | .get_drvinfo = hamachi_get_drvinfo, | |
1933 | .get_settings = hamachi_get_settings, | |
1934 | .set_settings = hamachi_set_settings, | |
1935 | .nway_reset = hamachi_nway_reset, | |
1936 | .get_link = hamachi_get_link, | |
1937 | }; | |
1938 | ||
1939 | static struct ethtool_ops ethtool_ops_no_mii = { | |
1940 | .begin = check_if_running, | |
1941 | .get_drvinfo = hamachi_get_drvinfo, | |
1942 | }; | |
1943 | ||
1944 | static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) | |
1945 | { | |
1946 | struct hamachi_private *np = netdev_priv(dev); | |
1947 | struct mii_ioctl_data *data = if_mii(rq); | |
1948 | int rc; | |
1949 | ||
1950 | if (!netif_running(dev)) | |
1951 | return -EINVAL; | |
1952 | ||
1953 | if (cmd == (SIOCDEVPRIVATE+3)) { /* set rx,tx intr params */ | |
1954 | u32 *d = (u32 *)&rq->ifr_ifru; | |
1955 | /* Should add this check here or an ordinary user can do nasty | |
1956 | * things. -KDU | |
1957 | * | |
1958 | * TODO: Shut down the Rx and Tx engines while doing this. | |
1959 | */ | |
1960 | if (!capable(CAP_NET_ADMIN)) | |
1961 | return -EPERM; | |
1962 | writel(d[0], np->base + TxIntrCtrl); | |
1963 | writel(d[1], np->base + RxIntrCtrl); | |
1964 | printk(KERN_NOTICE "%s: tx %08x, rx %08x intr\n", dev->name, | |
1965 | (u32) readl(np->base + TxIntrCtrl), | |
1966 | (u32) readl(np->base + RxIntrCtrl)); | |
1967 | rc = 0; | |
1968 | } | |
1969 | ||
1970 | else { | |
1971 | spin_lock_irq(&np->lock); | |
1972 | rc = generic_mii_ioctl(&np->mii_if, data, cmd, NULL); | |
1973 | spin_unlock_irq(&np->lock); | |
1974 | } | |
1975 | ||
1976 | return rc; | |
1977 | } | |
1978 | ||
1979 | ||
1980 | static void __devexit hamachi_remove_one (struct pci_dev *pdev) | |
1981 | { | |
1982 | struct net_device *dev = pci_get_drvdata(pdev); | |
1983 | ||
1984 | if (dev) { | |
1985 | struct hamachi_private *hmp = netdev_priv(dev); | |
1986 | ||
1987 | pci_free_consistent(pdev, RX_TOTAL_SIZE, hmp->rx_ring, | |
1988 | hmp->rx_ring_dma); | |
1989 | pci_free_consistent(pdev, TX_TOTAL_SIZE, hmp->tx_ring, | |
1990 | hmp->tx_ring_dma); | |
1991 | unregister_netdev(dev); | |
1992 | iounmap(hmp->base); | |
1993 | free_netdev(dev); | |
1994 | pci_release_regions(pdev); | |
1995 | pci_set_drvdata(pdev, NULL); | |
1996 | } | |
1997 | } | |
1998 | ||
1999 | static struct pci_device_id hamachi_pci_tbl[] = { | |
2000 | { 0x1318, 0x0911, PCI_ANY_ID, PCI_ANY_ID, }, | |
2001 | { 0, } | |
2002 | }; | |
2003 | MODULE_DEVICE_TABLE(pci, hamachi_pci_tbl); | |
2004 | ||
2005 | static struct pci_driver hamachi_driver = { | |
2006 | .name = DRV_NAME, | |
2007 | .id_table = hamachi_pci_tbl, | |
2008 | .probe = hamachi_init_one, | |
2009 | .remove = __devexit_p(hamachi_remove_one), | |
2010 | }; | |
2011 | ||
2012 | static int __init hamachi_init (void) | |
2013 | { | |
2014 | /* when a module, this is printed whether or not devices are found in probe */ | |
2015 | #ifdef MODULE | |
2016 | printk(version); | |
2017 | #endif | |
2018 | return pci_register_driver(&hamachi_driver); | |
2019 | } | |
2020 | ||
2021 | static void __exit hamachi_exit (void) | |
2022 | { | |
2023 | pci_unregister_driver(&hamachi_driver); | |
2024 | } | |
2025 | ||
2026 | ||
2027 | module_init(hamachi_init); | |
2028 | module_exit(hamachi_exit); |