Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* 3c574.c: A PCMCIA ethernet driver for the 3com 3c574 "RoadRunner". |
2 | ||
3 | Written 1993-1998 by | |
4 | Donald Becker, becker@scyld.com, (driver core) and | |
5 | David Hinds, dahinds@users.sourceforge.net (from his PC card code). | |
6 | Locking fixes (C) Copyright 2003 Red Hat Inc | |
7 | ||
8 | This software may be used and distributed according to the terms of | |
9 | the GNU General Public License, incorporated herein by reference. | |
10 | ||
11 | This driver derives from Donald Becker's 3c509 core, which has the | |
12 | following copyright: | |
13 | Copyright 1993 United States Government as represented by the | |
14 | Director, National Security Agency. | |
15 | ||
16 | ||
17 | */ | |
18 | ||
19 | /* | |
20 | Theory of Operation | |
21 | ||
22 | I. Board Compatibility | |
23 | ||
24 | This device driver is designed for the 3Com 3c574 PC card Fast Ethernet | |
25 | Adapter. | |
26 | ||
27 | II. Board-specific settings | |
28 | ||
29 | None -- PC cards are autoconfigured. | |
30 | ||
31 | III. Driver operation | |
32 | ||
33 | The 3c574 uses a Boomerang-style interface, without the bus-master capability. | |
34 | See the Boomerang driver and documentation for most details. | |
35 | ||
36 | IV. Notes and chip documentation. | |
37 | ||
38 | Two added registers are used to enhance PIO performance, RunnerRdCtrl and | |
39 | RunnerWrCtrl. These are 11 bit down-counters that are preloaded with the | |
40 | count of word (16 bits) reads or writes the driver is about to do to the Rx | |
41 | or Tx FIFO. The chip is then able to hide the internal-PCI-bus to PC-card | |
42 | translation latency by buffering the I/O operations with an 8 word FIFO. | |
43 | Note: No other chip accesses are permitted when this buffer is used. | |
44 | ||
45 | A second enhancement is that both attribute and common memory space | |
46 | 0x0800-0x0fff can translated to the PIO FIFO. Thus memory operations (faster | |
47 | with *some* PCcard bridges) may be used instead of I/O operations. | |
48 | This is enabled by setting the 0x10 bit in the PCMCIA LAN COR. | |
49 | ||
50 | Some slow PC card bridges work better if they never see a WAIT signal. | |
51 | This is configured by setting the 0x20 bit in the PCMCIA LAN COR. | |
52 | Only do this after testing that it is reliable and improves performance. | |
53 | ||
54 | The upper five bits of RunnerRdCtrl are used to window into PCcard | |
55 | configuration space registers. Window 0 is the regular Boomerang/Odie | |
56 | register set, 1-5 are various PC card control registers, and 16-31 are | |
57 | the (reversed!) CIS table. | |
58 | ||
59 | A final note: writing the InternalConfig register in window 3 with an | |
60 | invalid ramWidth is Very Bad. | |
61 | ||
62 | V. References | |
63 | ||
64 | http://www.scyld.com/expert/NWay.html | |
65 | http://www.national.com/pf/DP/DP83840.html | |
66 | ||
67 | Thanks to Terry Murphy of 3Com for providing development information for | |
68 | earlier 3Com products. | |
69 | ||
70 | */ | |
71 | ||
72 | #include <linux/module.h> | |
73 | #include <linux/kernel.h> | |
74 | #include <linux/init.h> | |
75 | #include <linux/slab.h> | |
76 | #include <linux/string.h> | |
77 | #include <linux/timer.h> | |
78 | #include <linux/interrupt.h> | |
79 | #include <linux/in.h> | |
80 | #include <linux/delay.h> | |
81 | #include <linux/netdevice.h> | |
82 | #include <linux/etherdevice.h> | |
83 | #include <linux/skbuff.h> | |
84 | #include <linux/if_arp.h> | |
85 | #include <linux/ioport.h> | |
1da177e4 | 86 | #include <linux/bitops.h> |
0fa0ee05 | 87 | #include <linux/mii.h> |
1da177e4 | 88 | |
1da177e4 LT |
89 | #include <pcmcia/cs.h> |
90 | #include <pcmcia/cistpl.h> | |
91 | #include <pcmcia/cisreg.h> | |
92 | #include <pcmcia/ciscode.h> | |
93 | #include <pcmcia/ds.h> | |
1da177e4 LT |
94 | |
95 | #include <asm/uaccess.h> | |
96 | #include <asm/io.h> | |
97 | #include <asm/system.h> | |
98 | ||
99 | /*====================================================================*/ | |
100 | ||
101 | /* Module parameters */ | |
102 | ||
103 | MODULE_AUTHOR("David Hinds <dahinds@users.sourceforge.net>"); | |
104 | MODULE_DESCRIPTION("3Com 3c574 series PCMCIA ethernet driver"); | |
105 | MODULE_LICENSE("GPL"); | |
106 | ||
107 | #define INT_MODULE_PARM(n, v) static int n = v; module_param(n, int, 0) | |
108 | ||
109 | /* Maximum events (Rx packets, etc.) to handle at each interrupt. */ | |
110 | INT_MODULE_PARM(max_interrupt_work, 32); | |
111 | ||
112 | /* Force full duplex modes? */ | |
113 | INT_MODULE_PARM(full_duplex, 0); | |
114 | ||
115 | /* Autodetect link polarity reversal? */ | |
116 | INT_MODULE_PARM(auto_polarity, 1); | |
117 | ||
1da177e4 LT |
118 | |
119 | /*====================================================================*/ | |
120 | ||
121 | /* Time in jiffies before concluding the transmitter is hung. */ | |
122 | #define TX_TIMEOUT ((800*HZ)/1000) | |
123 | ||
124 | /* To minimize the size of the driver source and make the driver more | |
125 | readable not all constants are symbolically defined. | |
126 | You'll need the manual if you want to understand driver details anyway. */ | |
127 | /* Offsets from base I/O address. */ | |
128 | #define EL3_DATA 0x00 | |
129 | #define EL3_CMD 0x0e | |
130 | #define EL3_STATUS 0x0e | |
131 | ||
132 | #define EL3WINDOW(win_num) outw(SelectWindow + (win_num), ioaddr + EL3_CMD) | |
133 | ||
134 | /* The top five bits written to EL3_CMD are a command, the lower | |
135 | 11 bits are the parameter, if applicable. */ | |
136 | enum el3_cmds { | |
137 | TotalReset = 0<<11, SelectWindow = 1<<11, StartCoax = 2<<11, | |
138 | RxDisable = 3<<11, RxEnable = 4<<11, RxReset = 5<<11, RxDiscard = 8<<11, | |
139 | TxEnable = 9<<11, TxDisable = 10<<11, TxReset = 11<<11, | |
140 | FakeIntr = 12<<11, AckIntr = 13<<11, SetIntrEnb = 14<<11, | |
141 | SetStatusEnb = 15<<11, SetRxFilter = 16<<11, SetRxThreshold = 17<<11, | |
142 | SetTxThreshold = 18<<11, SetTxStart = 19<<11, StatsEnable = 21<<11, | |
143 | StatsDisable = 22<<11, StopCoax = 23<<11, | |
144 | }; | |
145 | ||
146 | enum elxl_status { | |
147 | IntLatch = 0x0001, AdapterFailure = 0x0002, TxComplete = 0x0004, | |
148 | TxAvailable = 0x0008, RxComplete = 0x0010, RxEarly = 0x0020, | |
149 | IntReq = 0x0040, StatsFull = 0x0080, CmdBusy = 0x1000 }; | |
150 | ||
151 | /* The SetRxFilter command accepts the following classes: */ | |
152 | enum RxFilter { | |
153 | RxStation = 1, RxMulticast = 2, RxBroadcast = 4, RxProm = 8 | |
154 | }; | |
155 | ||
156 | enum Window0 { | |
157 | Wn0EepromCmd = 10, Wn0EepromData = 12, /* EEPROM command/address, data. */ | |
158 | IntrStatus=0x0E, /* Valid in all windows. */ | |
159 | }; | |
160 | /* These assumes the larger EEPROM. */ | |
161 | enum Win0_EEPROM_cmds { | |
162 | EEPROM_Read = 0x200, EEPROM_WRITE = 0x100, EEPROM_ERASE = 0x300, | |
163 | EEPROM_EWENB = 0x30, /* Enable erasing/writing for 10 msec. */ | |
164 | EEPROM_EWDIS = 0x00, /* Disable EWENB before 10 msec timeout. */ | |
165 | }; | |
166 | ||
167 | /* Register window 1 offsets, the window used in normal operation. | |
168 | On the "Odie" this window is always mapped at offsets 0x10-0x1f. | |
169 | Except for TxFree, which is overlapped by RunnerWrCtrl. */ | |
170 | enum Window1 { | |
171 | TX_FIFO = 0x10, RX_FIFO = 0x10, RxErrors = 0x14, | |
172 | RxStatus = 0x18, Timer=0x1A, TxStatus = 0x1B, | |
173 | TxFree = 0x0C, /* Remaining free bytes in Tx buffer. */ | |
174 | RunnerRdCtrl = 0x16, RunnerWrCtrl = 0x1c, | |
175 | }; | |
176 | ||
177 | enum Window3 { /* Window 3: MAC/config bits. */ | |
178 | Wn3_Config=0, Wn3_MAC_Ctrl=6, Wn3_Options=8, | |
179 | }; | |
b6659824 AV |
180 | enum wn3_config { |
181 | Ram_size = 7, | |
182 | Ram_width = 8, | |
183 | Ram_speed = 0x30, | |
184 | Rom_size = 0xc0, | |
185 | Ram_split_shift = 16, | |
186 | Ram_split = 3 << Ram_split_shift, | |
187 | Xcvr_shift = 20, | |
188 | Xcvr = 7 << Xcvr_shift, | |
189 | Autoselect = 0x1000000, | |
1da177e4 LT |
190 | }; |
191 | ||
192 | enum Window4 { /* Window 4: Xcvr/media bits. */ | |
193 | Wn4_FIFODiag = 4, Wn4_NetDiag = 6, Wn4_PhysicalMgmt=8, Wn4_Media = 10, | |
194 | }; | |
195 | ||
196 | #define MEDIA_TP 0x00C0 /* Enable link beat and jabber for 10baseT. */ | |
197 | ||
198 | struct el3_private { | |
fd238232 | 199 | struct pcmcia_device *p_dev; |
1da177e4 LT |
200 | u16 advertising, partner; /* NWay media advertisement */ |
201 | unsigned char phys; /* MII device address */ | |
202 | unsigned int autoselect:1, default_media:3; /* Read from the EEPROM/Wn3_Config. */ | |
203 | /* for transceiver monitoring */ | |
204 | struct timer_list media; | |
205 | unsigned short media_status; | |
206 | unsigned short fast_poll; | |
207 | unsigned long last_irq; | |
208 | spinlock_t window_lock; /* Guards the Window selection */ | |
209 | }; | |
210 | ||
211 | /* Set iff a MII transceiver on any interface requires mdio preamble. | |
212 | This only set with the original DP83840 on older 3c905 boards, so the extra | |
213 | code size of a per-interface flag is not worthwhile. */ | |
214 | static char mii_preamble_required = 0; | |
215 | ||
216 | /* Index of functions. */ | |
217 | ||
15b99ac1 | 218 | static int tc574_config(struct pcmcia_device *link); |
fba395ee | 219 | static void tc574_release(struct pcmcia_device *link); |
1da177e4 | 220 | |
906da809 OJ |
221 | static void mdio_sync(unsigned int ioaddr, int bits); |
222 | static int mdio_read(unsigned int ioaddr, int phy_id, int location); | |
223 | static void mdio_write(unsigned int ioaddr, int phy_id, int location, | |
224 | int value); | |
225 | static unsigned short read_eeprom(unsigned int ioaddr, int index); | |
1da177e4 LT |
226 | static void tc574_wait_for_completion(struct net_device *dev, int cmd); |
227 | ||
228 | static void tc574_reset(struct net_device *dev); | |
229 | static void media_check(unsigned long arg); | |
230 | static int el3_open(struct net_device *dev); | |
dbf02fae SH |
231 | static netdev_tx_t el3_start_xmit(struct sk_buff *skb, |
232 | struct net_device *dev); | |
7d12e780 | 233 | static irqreturn_t el3_interrupt(int irq, void *dev_id); |
1da177e4 LT |
234 | static void update_stats(struct net_device *dev); |
235 | static struct net_device_stats *el3_get_stats(struct net_device *dev); | |
236 | static int el3_rx(struct net_device *dev, int worklimit); | |
237 | static int el3_close(struct net_device *dev); | |
238 | static void el3_tx_timeout(struct net_device *dev); | |
239 | static int el3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); | |
1da177e4 | 240 | static void set_rx_mode(struct net_device *dev); |
e3eef534 | 241 | static void set_multicast_list(struct net_device *dev); |
1da177e4 | 242 | |
cc3b4866 | 243 | static void tc574_detach(struct pcmcia_device *p_dev); |
1da177e4 | 244 | |
1da177e4 LT |
245 | /* |
246 | tc574_attach() creates an "instance" of the driver, allocating | |
247 | local data structures for one device. The device is registered | |
248 | with Card Services. | |
249 | */ | |
fb72e2ff SH |
250 | static const struct net_device_ops el3_netdev_ops = { |
251 | .ndo_open = el3_open, | |
252 | .ndo_stop = el3_close, | |
253 | .ndo_start_xmit = el3_start_xmit, | |
254 | .ndo_tx_timeout = el3_tx_timeout, | |
255 | .ndo_get_stats = el3_get_stats, | |
256 | .ndo_do_ioctl = el3_ioctl, | |
e3eef534 | 257 | .ndo_set_multicast_list = set_multicast_list, |
fb72e2ff SH |
258 | .ndo_change_mtu = eth_change_mtu, |
259 | .ndo_set_mac_address = eth_mac_addr, | |
260 | .ndo_validate_addr = eth_validate_addr, | |
261 | }; | |
1da177e4 | 262 | |
15b99ac1 | 263 | static int tc574_probe(struct pcmcia_device *link) |
1da177e4 LT |
264 | { |
265 | struct el3_private *lp; | |
1da177e4 | 266 | struct net_device *dev; |
1da177e4 | 267 | |
dd0fab5b | 268 | dev_dbg(&link->dev, "3c574_attach()\n"); |
1da177e4 LT |
269 | |
270 | /* Create the PC card device object. */ | |
271 | dev = alloc_etherdev(sizeof(struct el3_private)); | |
272 | if (!dev) | |
f8cfa618 | 273 | return -ENOMEM; |
1da177e4 | 274 | lp = netdev_priv(dev); |
1da177e4 | 275 | link->priv = dev; |
fba395ee | 276 | lp->p_dev = link; |
1da177e4 LT |
277 | |
278 | spin_lock_init(&lp->window_lock); | |
90abdc3b DB |
279 | link->resource[0]->end = 32; |
280 | link->resource[0]->flags |= IO_DATA_PATH_WIDTH_16; | |
1da177e4 | 281 | link->conf.Attributes = CONF_ENABLE_IRQ; |
1da177e4 LT |
282 | link->conf.IntType = INT_MEMORY_AND_IO; |
283 | link->conf.ConfigIndex = 1; | |
1da177e4 | 284 | |
fb72e2ff | 285 | dev->netdev_ops = &el3_netdev_ops; |
1da177e4 | 286 | dev->watchdog_timeo = TX_TIMEOUT; |
1da177e4 | 287 | |
15b99ac1 | 288 | return tc574_config(link); |
1da177e4 LT |
289 | } /* tc574_attach */ |
290 | ||
291 | /* | |
292 | ||
293 | This deletes a driver "instance". The device is de-registered | |
294 | with Card Services. If it has been released, all local data | |
295 | structures are freed. Otherwise, the structures will be freed | |
296 | when the device is released. | |
297 | ||
298 | */ | |
299 | ||
fba395ee | 300 | static void tc574_detach(struct pcmcia_device *link) |
1da177e4 LT |
301 | { |
302 | struct net_device *dev = link->priv; | |
1da177e4 | 303 | |
dd0fab5b | 304 | dev_dbg(&link->dev, "3c574_detach()\n"); |
1da177e4 | 305 | |
c7c2fa07 | 306 | unregister_netdev(dev); |
1da177e4 | 307 | |
e2d40963 | 308 | tc574_release(link); |
1da177e4 | 309 | |
1da177e4 LT |
310 | free_netdev(dev); |
311 | } /* tc574_detach */ | |
312 | ||
313 | /* | |
314 | tc574_config() is scheduled to run after a CARD_INSERTION event | |
315 | is received, to configure the PCMCIA socket, and to make the | |
316 | ethernet device available to the system. | |
317 | */ | |
318 | ||
f71e1309 | 319 | static const char *ram_split[] = {"5:3", "3:1", "1:1", "3:5"}; |
1da177e4 | 320 | |
15b99ac1 | 321 | static int tc574_config(struct pcmcia_device *link) |
1da177e4 | 322 | { |
1da177e4 LT |
323 | struct net_device *dev = link->priv; |
324 | struct el3_private *lp = netdev_priv(dev); | |
dd0fab5b | 325 | int ret, i, j; |
906da809 | 326 | unsigned int ioaddr; |
b1e247ad | 327 | __be16 *phys_addr; |
1da177e4 | 328 | char *cardname; |
b6659824 | 329 | __u32 config; |
dddfbd82 DB |
330 | u8 *buf; |
331 | size_t len; | |
1da177e4 | 332 | |
b1e247ad | 333 | phys_addr = (__be16 *)dev->dev_addr; |
1da177e4 | 334 | |
dd0fab5b | 335 | dev_dbg(&link->dev, "3c574_config()\n"); |
1da177e4 | 336 | |
90abdc3b DB |
337 | link->io_lines = 16; |
338 | ||
1da177e4 | 339 | for (i = j = 0; j < 0x400; j += 0x20) { |
90abdc3b DB |
340 | link->resource[0]->start = j ^ 0x300; |
341 | i = pcmcia_request_io(link); | |
4c89e88b DB |
342 | if (i == 0) |
343 | break; | |
1da177e4 | 344 | } |
dd0fab5b DB |
345 | if (i != 0) |
346 | goto failed; | |
347 | ||
eb14120f | 348 | ret = pcmcia_request_irq(link, el3_interrupt); |
dd0fab5b DB |
349 | if (ret) |
350 | goto failed; | |
351 | ||
352 | ret = pcmcia_request_configuration(link, &link->conf); | |
353 | if (ret) | |
1da177e4 | 354 | goto failed; |
1da177e4 | 355 | |
eb14120f | 356 | dev->irq = link->irq; |
9a017a91 | 357 | dev->base_addr = link->resource[0]->start; |
1da177e4 LT |
358 | |
359 | ioaddr = dev->base_addr; | |
360 | ||
361 | /* The 3c574 normally uses an EEPROM for configuration info, including | |
362 | the hardware address. The future products may include a modem chip | |
363 | and put the address in the CIS. */ | |
dddfbd82 DB |
364 | |
365 | len = pcmcia_get_tuple(link, 0x88, &buf); | |
366 | if (buf && len >= 6) { | |
1da177e4 | 367 | for (i = 0; i < 3; i++) |
dddfbd82 DB |
368 | phys_addr[i] = htons(le16_to_cpu(buf[i * 2])); |
369 | kfree(buf); | |
1da177e4 | 370 | } else { |
dddfbd82 | 371 | kfree(buf); /* 0 < len < 6 */ |
1da177e4 LT |
372 | EL3WINDOW(0); |
373 | for (i = 0; i < 3; i++) | |
374 | phys_addr[i] = htons(read_eeprom(ioaddr, i + 10)); | |
b1e247ad | 375 | if (phys_addr[0] == htons(0x6060)) { |
1da177e4 LT |
376 | printk(KERN_NOTICE "3c574_cs: IO port conflict at 0x%03lx" |
377 | "-0x%03lx\n", dev->base_addr, dev->base_addr+15); | |
378 | goto failed; | |
379 | } | |
380 | } | |
a9606fd3 DB |
381 | if (link->prod_id[1]) |
382 | cardname = link->prod_id[1]; | |
383 | else | |
1da177e4 LT |
384 | cardname = "3Com 3c574"; |
385 | ||
386 | { | |
387 | u_char mcr; | |
388 | outw(2<<11, ioaddr + RunnerRdCtrl); | |
389 | mcr = inb(ioaddr + 2); | |
390 | outw(0<<11, ioaddr + RunnerRdCtrl); | |
391 | printk(KERN_INFO " ASIC rev %d,", mcr>>3); | |
392 | EL3WINDOW(3); | |
b6659824 AV |
393 | config = inl(ioaddr + Wn3_Config); |
394 | lp->default_media = (config & Xcvr) >> Xcvr_shift; | |
395 | lp->autoselect = config & Autoselect ? 1 : 0; | |
1da177e4 LT |
396 | } |
397 | ||
398 | init_timer(&lp->media); | |
399 | ||
400 | { | |
401 | int phy; | |
402 | ||
403 | /* Roadrunner only: Turn on the MII transceiver */ | |
404 | outw(0x8040, ioaddr + Wn3_Options); | |
405 | mdelay(1); | |
406 | outw(0xc040, ioaddr + Wn3_Options); | |
407 | tc574_wait_for_completion(dev, TxReset); | |
408 | tc574_wait_for_completion(dev, RxReset); | |
409 | mdelay(1); | |
410 | outw(0x8040, ioaddr + Wn3_Options); | |
411 | ||
412 | EL3WINDOW(4); | |
413 | for (phy = 1; phy <= 32; phy++) { | |
414 | int mii_status; | |
415 | mdio_sync(ioaddr, 32); | |
416 | mii_status = mdio_read(ioaddr, phy & 0x1f, 1); | |
417 | if (mii_status != 0xffff) { | |
418 | lp->phys = phy & 0x1f; | |
dd0fab5b DB |
419 | dev_dbg(&link->dev, " MII transceiver at " |
420 | "index %d, status %x.\n", | |
1da177e4 LT |
421 | phy, mii_status); |
422 | if ((mii_status & 0x0040) == 0) | |
423 | mii_preamble_required = 1; | |
424 | break; | |
425 | } | |
426 | } | |
427 | if (phy > 32) { | |
428 | printk(KERN_NOTICE " No MII transceivers found!\n"); | |
429 | goto failed; | |
430 | } | |
431 | i = mdio_read(ioaddr, lp->phys, 16) | 0x40; | |
432 | mdio_write(ioaddr, lp->phys, 16, i); | |
433 | lp->advertising = mdio_read(ioaddr, lp->phys, 4); | |
434 | if (full_duplex) { | |
435 | /* Only advertise the FD media types. */ | |
436 | lp->advertising &= ~0x02a0; | |
437 | mdio_write(ioaddr, lp->phys, 4, lp->advertising); | |
438 | } | |
439 | } | |
440 | ||
dd2e5a15 | 441 | SET_NETDEV_DEV(dev, &link->dev); |
1da177e4 LT |
442 | |
443 | if (register_netdev(dev) != 0) { | |
444 | printk(KERN_NOTICE "3c574_cs: register_netdev() failed\n"); | |
1da177e4 LT |
445 | goto failed; |
446 | } | |
447 | ||
0795af57 | 448 | printk(KERN_INFO "%s: %s at io %#3lx, irq %d, " |
e174961c | 449 | "hw_addr %pM.\n", |
0795af57 | 450 | dev->name, cardname, dev->base_addr, dev->irq, |
e174961c | 451 | dev->dev_addr); |
1da177e4 | 452 | printk(" %dK FIFO split %s Rx:Tx, %sMII interface.\n", |
b6659824 AV |
453 | 8 << config & Ram_size, |
454 | ram_split[(config & Ram_split) >> Ram_split_shift], | |
455 | config & Autoselect ? "autoselect " : ""); | |
1da177e4 | 456 | |
15b99ac1 | 457 | return 0; |
1da177e4 | 458 | |
1da177e4 LT |
459 | failed: |
460 | tc574_release(link); | |
15b99ac1 | 461 | return -ENODEV; |
1da177e4 LT |
462 | |
463 | } /* tc574_config */ | |
464 | ||
465 | /* | |
466 | After a card is removed, tc574_release() will unregister the net | |
467 | device, and release the PCMCIA configuration. If the device is | |
468 | still open, this will be postponed until it is closed. | |
469 | */ | |
470 | ||
fba395ee | 471 | static void tc574_release(struct pcmcia_device *link) |
1da177e4 | 472 | { |
fba395ee | 473 | pcmcia_disable_device(link); |
1da177e4 LT |
474 | } |
475 | ||
fba395ee | 476 | static int tc574_suspend(struct pcmcia_device *link) |
98e4c28b | 477 | { |
98e4c28b DB |
478 | struct net_device *dev = link->priv; |
479 | ||
e2d40963 | 480 | if (link->open) |
8661bb5b | 481 | netif_device_detach(dev); |
98e4c28b DB |
482 | |
483 | return 0; | |
484 | } | |
485 | ||
fba395ee | 486 | static int tc574_resume(struct pcmcia_device *link) |
98e4c28b | 487 | { |
98e4c28b DB |
488 | struct net_device *dev = link->priv; |
489 | ||
e2d40963 | 490 | if (link->open) { |
8661bb5b DB |
491 | tc574_reset(dev); |
492 | netif_device_attach(dev); | |
98e4c28b DB |
493 | } |
494 | ||
495 | return 0; | |
496 | } | |
497 | ||
1da177e4 LT |
498 | static void dump_status(struct net_device *dev) |
499 | { | |
906da809 | 500 | unsigned int ioaddr = dev->base_addr; |
1da177e4 LT |
501 | EL3WINDOW(1); |
502 | printk(KERN_INFO " irq status %04x, rx status %04x, tx status " | |
503 | "%02x, tx free %04x\n", inw(ioaddr+EL3_STATUS), | |
504 | inw(ioaddr+RxStatus), inb(ioaddr+TxStatus), | |
505 | inw(ioaddr+TxFree)); | |
506 | EL3WINDOW(4); | |
507 | printk(KERN_INFO " diagnostics: fifo %04x net %04x ethernet %04x" | |
508 | " media %04x\n", inw(ioaddr+0x04), inw(ioaddr+0x06), | |
509 | inw(ioaddr+0x08), inw(ioaddr+0x0a)); | |
510 | EL3WINDOW(1); | |
511 | } | |
512 | ||
513 | /* | |
514 | Use this for commands that may take time to finish | |
515 | */ | |
516 | static void tc574_wait_for_completion(struct net_device *dev, int cmd) | |
517 | { | |
518 | int i = 1500; | |
519 | outw(cmd, dev->base_addr + EL3_CMD); | |
520 | while (--i > 0) | |
521 | if (!(inw(dev->base_addr + EL3_STATUS) & 0x1000)) break; | |
522 | if (i == 0) | |
523 | printk(KERN_NOTICE "%s: command 0x%04x did not complete!\n", dev->name, cmd); | |
524 | } | |
525 | ||
526 | /* Read a word from the EEPROM using the regular EEPROM access register. | |
527 | Assume that we are in register window zero. | |
528 | */ | |
906da809 | 529 | static unsigned short read_eeprom(unsigned int ioaddr, int index) |
1da177e4 LT |
530 | { |
531 | int timer; | |
532 | outw(EEPROM_Read + index, ioaddr + Wn0EepromCmd); | |
533 | /* Pause for at least 162 usec for the read to take place. */ | |
534 | for (timer = 1620; timer >= 0; timer--) { | |
535 | if ((inw(ioaddr + Wn0EepromCmd) & 0x8000) == 0) | |
536 | break; | |
537 | } | |
538 | return inw(ioaddr + Wn0EepromData); | |
539 | } | |
540 | ||
541 | /* MII transceiver control section. | |
542 | Read and write the MII registers using software-generated serial | |
543 | MDIO protocol. See the MII specifications or DP83840A data sheet | |
544 | for details. | |
545 | The maxium data clock rate is 2.5 Mhz. The timing is easily met by the | |
546 | slow PC card interface. */ | |
547 | ||
548 | #define MDIO_SHIFT_CLK 0x01 | |
549 | #define MDIO_DIR_WRITE 0x04 | |
550 | #define MDIO_DATA_WRITE0 (0x00 | MDIO_DIR_WRITE) | |
551 | #define MDIO_DATA_WRITE1 (0x02 | MDIO_DIR_WRITE) | |
552 | #define MDIO_DATA_READ 0x02 | |
553 | #define MDIO_ENB_IN 0x00 | |
554 | ||
555 | /* Generate the preamble required for initial synchronization and | |
556 | a few older transceivers. */ | |
906da809 | 557 | static void mdio_sync(unsigned int ioaddr, int bits) |
1da177e4 | 558 | { |
906da809 | 559 | unsigned int mdio_addr = ioaddr + Wn4_PhysicalMgmt; |
1da177e4 LT |
560 | |
561 | /* Establish sync by sending at least 32 logic ones. */ | |
562 | while (-- bits >= 0) { | |
563 | outw(MDIO_DATA_WRITE1, mdio_addr); | |
564 | outw(MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, mdio_addr); | |
565 | } | |
566 | } | |
567 | ||
906da809 | 568 | static int mdio_read(unsigned int ioaddr, int phy_id, int location) |
1da177e4 LT |
569 | { |
570 | int i; | |
571 | int read_cmd = (0xf6 << 10) | (phy_id << 5) | location; | |
572 | unsigned int retval = 0; | |
906da809 | 573 | unsigned int mdio_addr = ioaddr + Wn4_PhysicalMgmt; |
1da177e4 LT |
574 | |
575 | if (mii_preamble_required) | |
576 | mdio_sync(ioaddr, 32); | |
577 | ||
578 | /* Shift the read command bits out. */ | |
579 | for (i = 14; i >= 0; i--) { | |
580 | int dataval = (read_cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0; | |
581 | outw(dataval, mdio_addr); | |
582 | outw(dataval | MDIO_SHIFT_CLK, mdio_addr); | |
583 | } | |
584 | /* Read the two transition, 16 data, and wire-idle bits. */ | |
585 | for (i = 19; i > 0; i--) { | |
586 | outw(MDIO_ENB_IN, mdio_addr); | |
587 | retval = (retval << 1) | ((inw(mdio_addr) & MDIO_DATA_READ) ? 1 : 0); | |
588 | outw(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr); | |
589 | } | |
590 | return (retval>>1) & 0xffff; | |
591 | } | |
592 | ||
906da809 | 593 | static void mdio_write(unsigned int ioaddr, int phy_id, int location, int value) |
1da177e4 LT |
594 | { |
595 | int write_cmd = 0x50020000 | (phy_id << 23) | (location << 18) | value; | |
906da809 | 596 | unsigned int mdio_addr = ioaddr + Wn4_PhysicalMgmt; |
1da177e4 LT |
597 | int i; |
598 | ||
599 | if (mii_preamble_required) | |
600 | mdio_sync(ioaddr, 32); | |
601 | ||
602 | /* Shift the command bits out. */ | |
603 | for (i = 31; i >= 0; i--) { | |
604 | int dataval = (write_cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0; | |
605 | outw(dataval, mdio_addr); | |
606 | outw(dataval | MDIO_SHIFT_CLK, mdio_addr); | |
607 | } | |
608 | /* Leave the interface idle. */ | |
609 | for (i = 1; i >= 0; i--) { | |
610 | outw(MDIO_ENB_IN, mdio_addr); | |
611 | outw(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr); | |
612 | } | |
1da177e4 LT |
613 | } |
614 | ||
615 | /* Reset and restore all of the 3c574 registers. */ | |
616 | static void tc574_reset(struct net_device *dev) | |
617 | { | |
618 | struct el3_private *lp = netdev_priv(dev); | |
619 | int i; | |
906da809 | 620 | unsigned int ioaddr = dev->base_addr; |
1da177e4 LT |
621 | unsigned long flags; |
622 | ||
623 | tc574_wait_for_completion(dev, TotalReset|0x10); | |
624 | ||
625 | spin_lock_irqsave(&lp->window_lock, flags); | |
626 | /* Clear any transactions in progress. */ | |
627 | outw(0, ioaddr + RunnerWrCtrl); | |
628 | outw(0, ioaddr + RunnerRdCtrl); | |
629 | ||
630 | /* Set the station address and mask. */ | |
631 | EL3WINDOW(2); | |
632 | for (i = 0; i < 6; i++) | |
633 | outb(dev->dev_addr[i], ioaddr + i); | |
634 | for (; i < 12; i+=2) | |
635 | outw(0, ioaddr + i); | |
636 | ||
637 | /* Reset config options */ | |
638 | EL3WINDOW(3); | |
639 | outb((dev->mtu > 1500 ? 0x40 : 0), ioaddr + Wn3_MAC_Ctrl); | |
640 | outl((lp->autoselect ? 0x01000000 : 0) | 0x0062001b, | |
641 | ioaddr + Wn3_Config); | |
642 | /* Roadrunner only: Turn on the MII transceiver. */ | |
643 | outw(0x8040, ioaddr + Wn3_Options); | |
644 | mdelay(1); | |
645 | outw(0xc040, ioaddr + Wn3_Options); | |
646 | EL3WINDOW(1); | |
647 | spin_unlock_irqrestore(&lp->window_lock, flags); | |
648 | ||
649 | tc574_wait_for_completion(dev, TxReset); | |
650 | tc574_wait_for_completion(dev, RxReset); | |
651 | mdelay(1); | |
652 | spin_lock_irqsave(&lp->window_lock, flags); | |
653 | EL3WINDOW(3); | |
654 | outw(0x8040, ioaddr + Wn3_Options); | |
655 | ||
656 | /* Switch to the stats window, and clear all stats by reading. */ | |
657 | outw(StatsDisable, ioaddr + EL3_CMD); | |
658 | EL3WINDOW(6); | |
659 | for (i = 0; i < 10; i++) | |
660 | inb(ioaddr + i); | |
661 | inw(ioaddr + 10); | |
662 | inw(ioaddr + 12); | |
663 | EL3WINDOW(4); | |
664 | inb(ioaddr + 12); | |
665 | inb(ioaddr + 13); | |
666 | ||
667 | /* .. enable any extra statistics bits.. */ | |
668 | outw(0x0040, ioaddr + Wn4_NetDiag); | |
669 | ||
670 | EL3WINDOW(1); | |
671 | spin_unlock_irqrestore(&lp->window_lock, flags); | |
672 | ||
673 | /* .. re-sync MII and re-fill what NWay is advertising. */ | |
674 | mdio_sync(ioaddr, 32); | |
675 | mdio_write(ioaddr, lp->phys, 4, lp->advertising); | |
676 | if (!auto_polarity) { | |
677 | /* works for TDK 78Q2120 series MII's */ | |
1569d9e8 | 678 | i = mdio_read(ioaddr, lp->phys, 16) | 0x20; |
1da177e4 LT |
679 | mdio_write(ioaddr, lp->phys, 16, i); |
680 | } | |
681 | ||
682 | spin_lock_irqsave(&lp->window_lock, flags); | |
683 | /* Switch to register set 1 for normal use, just for TxFree. */ | |
684 | set_rx_mode(dev); | |
685 | spin_unlock_irqrestore(&lp->window_lock, flags); | |
686 | outw(StatsEnable, ioaddr + EL3_CMD); /* Turn on statistics. */ | |
687 | outw(RxEnable, ioaddr + EL3_CMD); /* Enable the receiver. */ | |
688 | outw(TxEnable, ioaddr + EL3_CMD); /* Enable transmitter. */ | |
689 | /* Allow status bits to be seen. */ | |
690 | outw(SetStatusEnb | 0xff, ioaddr + EL3_CMD); | |
691 | /* Ack all pending events, and set active indicator mask. */ | |
692 | outw(AckIntr | IntLatch | TxAvailable | RxEarly | IntReq, | |
693 | ioaddr + EL3_CMD); | |
694 | outw(SetIntrEnb | IntLatch | TxAvailable | RxComplete | StatsFull | |
695 | | AdapterFailure | RxEarly, ioaddr + EL3_CMD); | |
696 | } | |
697 | ||
698 | static int el3_open(struct net_device *dev) | |
699 | { | |
700 | struct el3_private *lp = netdev_priv(dev); | |
fba395ee | 701 | struct pcmcia_device *link = lp->p_dev; |
1da177e4 | 702 | |
9940ec36 | 703 | if (!pcmcia_dev_present(link)) |
1da177e4 LT |
704 | return -ENODEV; |
705 | ||
706 | link->open++; | |
707 | netif_start_queue(dev); | |
708 | ||
709 | tc574_reset(dev); | |
710 | lp->media.function = &media_check; | |
711 | lp->media.data = (unsigned long) dev; | |
712 | lp->media.expires = jiffies + HZ; | |
713 | add_timer(&lp->media); | |
714 | ||
dd0fab5b | 715 | dev_dbg(&link->dev, "%s: opened, status %4.4x.\n", |
1da177e4 LT |
716 | dev->name, inw(dev->base_addr + EL3_STATUS)); |
717 | ||
718 | return 0; | |
719 | } | |
720 | ||
721 | static void el3_tx_timeout(struct net_device *dev) | |
722 | { | |
906da809 | 723 | unsigned int ioaddr = dev->base_addr; |
1da177e4 LT |
724 | |
725 | printk(KERN_NOTICE "%s: Transmit timed out!\n", dev->name); | |
726 | dump_status(dev); | |
2e8d31d5 | 727 | dev->stats.tx_errors++; |
1ae5dc34 | 728 | dev->trans_start = jiffies; /* prevent tx timeout */ |
1da177e4 LT |
729 | /* Issue TX_RESET and TX_START commands. */ |
730 | tc574_wait_for_completion(dev, TxReset); | |
731 | outw(TxEnable, ioaddr + EL3_CMD); | |
732 | netif_wake_queue(dev); | |
733 | } | |
734 | ||
735 | static void pop_tx_status(struct net_device *dev) | |
736 | { | |
906da809 | 737 | unsigned int ioaddr = dev->base_addr; |
1da177e4 LT |
738 | int i; |
739 | ||
740 | /* Clear the Tx status stack. */ | |
741 | for (i = 32; i > 0; i--) { | |
742 | u_char tx_status = inb(ioaddr + TxStatus); | |
743 | if (!(tx_status & 0x84)) | |
744 | break; | |
745 | /* reset transmitter on jabber error or underrun */ | |
746 | if (tx_status & 0x30) | |
747 | tc574_wait_for_completion(dev, TxReset); | |
748 | if (tx_status & 0x38) { | |
dd0fab5b | 749 | pr_debug("%s: transmit error: status 0x%02x\n", |
1da177e4 LT |
750 | dev->name, tx_status); |
751 | outw(TxEnable, ioaddr + EL3_CMD); | |
2e8d31d5 | 752 | dev->stats.tx_aborted_errors++; |
1da177e4 LT |
753 | } |
754 | outb(0x00, ioaddr + TxStatus); /* Pop the status stack. */ | |
755 | } | |
756 | } | |
757 | ||
dbf02fae SH |
758 | static netdev_tx_t el3_start_xmit(struct sk_buff *skb, |
759 | struct net_device *dev) | |
1da177e4 | 760 | { |
906da809 | 761 | unsigned int ioaddr = dev->base_addr; |
1da177e4 LT |
762 | struct el3_private *lp = netdev_priv(dev); |
763 | unsigned long flags; | |
764 | ||
dd0fab5b | 765 | pr_debug("%s: el3_start_xmit(length = %ld) called, " |
1da177e4 LT |
766 | "status %4.4x.\n", dev->name, (long)skb->len, |
767 | inw(ioaddr + EL3_STATUS)); | |
768 | ||
769 | spin_lock_irqsave(&lp->window_lock, flags); | |
df245dce AK |
770 | |
771 | dev->stats.tx_bytes += skb->len; | |
772 | ||
773 | /* Put out the doubleword header... */ | |
1da177e4 LT |
774 | outw(skb->len, ioaddr + TX_FIFO); |
775 | outw(0, ioaddr + TX_FIFO); | |
df245dce | 776 | /* ... and the packet rounded to a doubleword. */ |
1da177e4 LT |
777 | outsl(ioaddr + TX_FIFO, skb->data, (skb->len+3)>>2); |
778 | ||
1da177e4 LT |
779 | /* TxFree appears only in Window 1, not offset 0x1c. */ |
780 | if (inw(ioaddr + TxFree) <= 1536) { | |
781 | netif_stop_queue(dev); | |
782 | /* Interrupt us when the FIFO has room for max-sized packet. | |
783 | The threshold is in units of dwords. */ | |
784 | outw(SetTxThreshold + (1536>>2), ioaddr + EL3_CMD); | |
785 | } | |
786 | ||
787 | pop_tx_status(dev); | |
788 | spin_unlock_irqrestore(&lp->window_lock, flags); | |
789 | dev_kfree_skb(skb); | |
6ed10654 | 790 | return NETDEV_TX_OK; |
1da177e4 LT |
791 | } |
792 | ||
793 | /* The EL3 interrupt handler. */ | |
7d12e780 | 794 | static irqreturn_t el3_interrupt(int irq, void *dev_id) |
1da177e4 LT |
795 | { |
796 | struct net_device *dev = (struct net_device *) dev_id; | |
797 | struct el3_private *lp = netdev_priv(dev); | |
906da809 | 798 | unsigned int ioaddr; |
1da177e4 LT |
799 | unsigned status; |
800 | int work_budget = max_interrupt_work; | |
801 | int handled = 0; | |
802 | ||
803 | if (!netif_device_present(dev)) | |
804 | return IRQ_NONE; | |
805 | ioaddr = dev->base_addr; | |
806 | ||
dd0fab5b | 807 | pr_debug("%s: interrupt, status %4.4x.\n", |
1da177e4 LT |
808 | dev->name, inw(ioaddr + EL3_STATUS)); |
809 | ||
810 | spin_lock(&lp->window_lock); | |
811 | ||
812 | while ((status = inw(ioaddr + EL3_STATUS)) & | |
813 | (IntLatch | RxComplete | RxEarly | StatsFull)) { | |
814 | if (!netif_device_present(dev) || | |
815 | ((status & 0xe000) != 0x2000)) { | |
dd0fab5b | 816 | pr_debug("%s: Interrupt from dead card\n", dev->name); |
1da177e4 LT |
817 | break; |
818 | } | |
819 | ||
820 | handled = 1; | |
821 | ||
822 | if (status & RxComplete) | |
823 | work_budget = el3_rx(dev, work_budget); | |
824 | ||
825 | if (status & TxAvailable) { | |
dd0fab5b | 826 | pr_debug(" TX room bit was handled.\n"); |
1da177e4 LT |
827 | /* There's room in the FIFO for a full-sized packet. */ |
828 | outw(AckIntr | TxAvailable, ioaddr + EL3_CMD); | |
829 | netif_wake_queue(dev); | |
830 | } | |
831 | ||
832 | if (status & TxComplete) | |
833 | pop_tx_status(dev); | |
834 | ||
835 | if (status & (AdapterFailure | RxEarly | StatsFull)) { | |
836 | /* Handle all uncommon interrupts. */ | |
837 | if (status & StatsFull) | |
838 | update_stats(dev); | |
839 | if (status & RxEarly) { | |
840 | work_budget = el3_rx(dev, work_budget); | |
841 | outw(AckIntr | RxEarly, ioaddr + EL3_CMD); | |
842 | } | |
843 | if (status & AdapterFailure) { | |
844 | u16 fifo_diag; | |
845 | EL3WINDOW(4); | |
846 | fifo_diag = inw(ioaddr + Wn4_FIFODiag); | |
847 | EL3WINDOW(1); | |
848 | printk(KERN_NOTICE "%s: adapter failure, FIFO diagnostic" | |
849 | " register %04x.\n", dev->name, fifo_diag); | |
850 | if (fifo_diag & 0x0400) { | |
851 | /* Tx overrun */ | |
852 | tc574_wait_for_completion(dev, TxReset); | |
853 | outw(TxEnable, ioaddr + EL3_CMD); | |
854 | } | |
855 | if (fifo_diag & 0x2000) { | |
856 | /* Rx underrun */ | |
857 | tc574_wait_for_completion(dev, RxReset); | |
858 | set_rx_mode(dev); | |
859 | outw(RxEnable, ioaddr + EL3_CMD); | |
860 | } | |
861 | outw(AckIntr | AdapterFailure, ioaddr + EL3_CMD); | |
862 | } | |
863 | } | |
864 | ||
865 | if (--work_budget < 0) { | |
dd0fab5b | 866 | pr_debug("%s: Too much work in interrupt, " |
1da177e4 LT |
867 | "status %4.4x.\n", dev->name, status); |
868 | /* Clear all interrupts */ | |
869 | outw(AckIntr | 0xFF, ioaddr + EL3_CMD); | |
870 | break; | |
871 | } | |
872 | /* Acknowledge the IRQ. */ | |
873 | outw(AckIntr | IntReq | IntLatch, ioaddr + EL3_CMD); | |
874 | } | |
875 | ||
dd0fab5b | 876 | pr_debug("%s: exiting interrupt, status %4.4x.\n", |
1da177e4 LT |
877 | dev->name, inw(ioaddr + EL3_STATUS)); |
878 | ||
879 | spin_unlock(&lp->window_lock); | |
880 | return IRQ_RETVAL(handled); | |
881 | } | |
882 | ||
883 | /* | |
884 | This timer serves two purposes: to check for missed interrupts | |
885 | (and as a last resort, poll the NIC for events), and to monitor | |
886 | the MII, reporting changes in cable status. | |
887 | */ | |
888 | static void media_check(unsigned long arg) | |
889 | { | |
890 | struct net_device *dev = (struct net_device *) arg; | |
891 | struct el3_private *lp = netdev_priv(dev); | |
906da809 | 892 | unsigned int ioaddr = dev->base_addr; |
1da177e4 LT |
893 | unsigned long flags; |
894 | unsigned short /* cable, */ media, partner; | |
895 | ||
896 | if (!netif_device_present(dev)) | |
897 | goto reschedule; | |
898 | ||
899 | /* Check for pending interrupt with expired latency timer: with | |
900 | this, we can limp along even if the interrupt is blocked */ | |
901 | if ((inw(ioaddr + EL3_STATUS) & IntLatch) && (inb(ioaddr + Timer) == 0xff)) { | |
902 | if (!lp->fast_poll) | |
903 | printk(KERN_INFO "%s: interrupt(s) dropped!\n", dev->name); | |
671c8806 KK |
904 | |
905 | local_irq_save(flags); | |
e363d138 | 906 | el3_interrupt(dev->irq, dev); |
671c8806 KK |
907 | local_irq_restore(flags); |
908 | ||
1da177e4 LT |
909 | lp->fast_poll = HZ; |
910 | } | |
911 | if (lp->fast_poll) { | |
912 | lp->fast_poll--; | |
913 | lp->media.expires = jiffies + 2*HZ/100; | |
914 | add_timer(&lp->media); | |
915 | return; | |
916 | } | |
917 | ||
918 | spin_lock_irqsave(&lp->window_lock, flags); | |
919 | EL3WINDOW(4); | |
920 | media = mdio_read(ioaddr, lp->phys, 1); | |
921 | partner = mdio_read(ioaddr, lp->phys, 5); | |
922 | EL3WINDOW(1); | |
923 | ||
924 | if (media != lp->media_status) { | |
925 | if ((media ^ lp->media_status) & 0x0004) | |
926 | printk(KERN_INFO "%s: %s link beat\n", dev->name, | |
927 | (lp->media_status & 0x0004) ? "lost" : "found"); | |
928 | if ((media ^ lp->media_status) & 0x0020) { | |
929 | lp->partner = 0; | |
930 | if (lp->media_status & 0x0020) { | |
931 | printk(KERN_INFO "%s: autonegotiation restarted\n", | |
932 | dev->name); | |
933 | } else if (partner) { | |
934 | partner &= lp->advertising; | |
935 | lp->partner = partner; | |
936 | printk(KERN_INFO "%s: autonegotiation complete: " | |
937 | "%sbaseT-%cD selected\n", dev->name, | |
938 | ((partner & 0x0180) ? "100" : "10"), | |
939 | ((partner & 0x0140) ? 'F' : 'H')); | |
940 | } else { | |
941 | printk(KERN_INFO "%s: link partner did not autonegotiate\n", | |
942 | dev->name); | |
943 | } | |
944 | ||
945 | EL3WINDOW(3); | |
946 | outb((partner & 0x0140 ? 0x20 : 0) | | |
947 | (dev->mtu > 1500 ? 0x40 : 0), ioaddr + Wn3_MAC_Ctrl); | |
948 | EL3WINDOW(1); | |
949 | ||
950 | } | |
951 | if (media & 0x0010) | |
952 | printk(KERN_INFO "%s: remote fault detected\n", | |
953 | dev->name); | |
954 | if (media & 0x0002) | |
955 | printk(KERN_INFO "%s: jabber detected\n", dev->name); | |
956 | lp->media_status = media; | |
957 | } | |
958 | spin_unlock_irqrestore(&lp->window_lock, flags); | |
959 | ||
960 | reschedule: | |
961 | lp->media.expires = jiffies + HZ; | |
962 | add_timer(&lp->media); | |
963 | } | |
964 | ||
965 | static struct net_device_stats *el3_get_stats(struct net_device *dev) | |
966 | { | |
967 | struct el3_private *lp = netdev_priv(dev); | |
968 | ||
969 | if (netif_device_present(dev)) { | |
970 | unsigned long flags; | |
971 | spin_lock_irqsave(&lp->window_lock, flags); | |
972 | update_stats(dev); | |
973 | spin_unlock_irqrestore(&lp->window_lock, flags); | |
974 | } | |
2e8d31d5 | 975 | return &dev->stats; |
1da177e4 LT |
976 | } |
977 | ||
978 | /* Update statistics. | |
979 | Suprisingly this need not be run single-threaded, but it effectively is. | |
980 | The counters clear when read, so the adds must merely be atomic. | |
981 | */ | |
982 | static void update_stats(struct net_device *dev) | |
983 | { | |
906da809 | 984 | unsigned int ioaddr = dev->base_addr; |
1da177e4 LT |
985 | u8 rx, tx, up; |
986 | ||
dd0fab5b | 987 | pr_debug("%s: updating the statistics.\n", dev->name); |
1da177e4 LT |
988 | |
989 | if (inw(ioaddr+EL3_STATUS) == 0xffff) /* No card. */ | |
990 | return; | |
991 | ||
992 | /* Unlike the 3c509 we need not turn off stats updates while reading. */ | |
993 | /* Switch to the stats window, and read everything. */ | |
994 | EL3WINDOW(6); | |
2e8d31d5 PZ |
995 | dev->stats.tx_carrier_errors += inb(ioaddr + 0); |
996 | dev->stats.tx_heartbeat_errors += inb(ioaddr + 1); | |
1da177e4 | 997 | /* Multiple collisions. */ inb(ioaddr + 2); |
2e8d31d5 PZ |
998 | dev->stats.collisions += inb(ioaddr + 3); |
999 | dev->stats.tx_window_errors += inb(ioaddr + 4); | |
1000 | dev->stats.rx_fifo_errors += inb(ioaddr + 5); | |
1001 | dev->stats.tx_packets += inb(ioaddr + 6); | |
1da177e4 | 1002 | up = inb(ioaddr + 9); |
2e8d31d5 | 1003 | dev->stats.tx_packets += (up&0x30) << 4; |
1da177e4 LT |
1004 | /* Rx packets */ inb(ioaddr + 7); |
1005 | /* Tx deferrals */ inb(ioaddr + 8); | |
1006 | rx = inw(ioaddr + 10); | |
1007 | tx = inw(ioaddr + 12); | |
1008 | ||
1009 | EL3WINDOW(4); | |
1010 | /* BadSSD */ inb(ioaddr + 12); | |
1011 | up = inb(ioaddr + 13); | |
1012 | ||
1da177e4 LT |
1013 | EL3WINDOW(1); |
1014 | } | |
1015 | ||
1016 | static int el3_rx(struct net_device *dev, int worklimit) | |
1017 | { | |
906da809 | 1018 | unsigned int ioaddr = dev->base_addr; |
1da177e4 LT |
1019 | short rx_status; |
1020 | ||
dd0fab5b | 1021 | pr_debug("%s: in rx_packet(), status %4.4x, rx_status %4.4x.\n", |
1da177e4 LT |
1022 | dev->name, inw(ioaddr+EL3_STATUS), inw(ioaddr+RxStatus)); |
1023 | while (!((rx_status = inw(ioaddr + RxStatus)) & 0x8000) && | |
b9bdcd9b RK |
1024 | worklimit > 0) { |
1025 | worklimit--; | |
1da177e4 LT |
1026 | if (rx_status & 0x4000) { /* Error, update stats. */ |
1027 | short error = rx_status & 0x3800; | |
2e8d31d5 | 1028 | dev->stats.rx_errors++; |
1da177e4 | 1029 | switch (error) { |
2e8d31d5 PZ |
1030 | case 0x0000: dev->stats.rx_over_errors++; break; |
1031 | case 0x0800: dev->stats.rx_length_errors++; break; | |
1032 | case 0x1000: dev->stats.rx_frame_errors++; break; | |
1033 | case 0x1800: dev->stats.rx_length_errors++; break; | |
1034 | case 0x2000: dev->stats.rx_frame_errors++; break; | |
1035 | case 0x2800: dev->stats.rx_crc_errors++; break; | |
1da177e4 LT |
1036 | } |
1037 | } else { | |
1038 | short pkt_len = rx_status & 0x7ff; | |
1039 | struct sk_buff *skb; | |
1040 | ||
1041 | skb = dev_alloc_skb(pkt_len+5); | |
1042 | ||
dd0fab5b | 1043 | pr_debug(" Receiving packet size %d status %4.4x.\n", |
1da177e4 LT |
1044 | pkt_len, rx_status); |
1045 | if (skb != NULL) { | |
1da177e4 LT |
1046 | skb_reserve(skb, 2); |
1047 | insl(ioaddr+RX_FIFO, skb_put(skb, pkt_len), | |
1048 | ((pkt_len+3)>>2)); | |
1049 | skb->protocol = eth_type_trans(skb, dev); | |
1050 | netif_rx(skb); | |
2e8d31d5 PZ |
1051 | dev->stats.rx_packets++; |
1052 | dev->stats.rx_bytes += pkt_len; | |
1da177e4 | 1053 | } else { |
dd0fab5b | 1054 | pr_debug("%s: couldn't allocate a sk_buff of" |
1da177e4 | 1055 | " size %d.\n", dev->name, pkt_len); |
2e8d31d5 | 1056 | dev->stats.rx_dropped++; |
1da177e4 LT |
1057 | } |
1058 | } | |
1059 | tc574_wait_for_completion(dev, RxDiscard); | |
1060 | } | |
1061 | ||
1062 | return worklimit; | |
1063 | } | |
1064 | ||
1da177e4 LT |
1065 | /* Provide ioctl() calls to examine the MII xcvr state. */ |
1066 | static int el3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) | |
1067 | { | |
1068 | struct el3_private *lp = netdev_priv(dev); | |
906da809 | 1069 | unsigned int ioaddr = dev->base_addr; |
0fa0ee05 | 1070 | struct mii_ioctl_data *data = if_mii(rq); |
1da177e4 LT |
1071 | int phy = lp->phys & 0x1f; |
1072 | ||
dd0fab5b | 1073 | pr_debug("%s: In ioct(%-.6s, %#4.4x) %4.4x %4.4x %4.4x %4.4x.\n", |
1da177e4 | 1074 | dev->name, rq->ifr_ifrn.ifrn_name, cmd, |
0fa0ee05 | 1075 | data->phy_id, data->reg_num, data->val_in, data->val_out); |
1da177e4 LT |
1076 | |
1077 | switch(cmd) { | |
1078 | case SIOCGMIIPHY: /* Get the address of the PHY in use. */ | |
0fa0ee05 | 1079 | data->phy_id = phy; |
1da177e4 LT |
1080 | case SIOCGMIIREG: /* Read the specified MII register. */ |
1081 | { | |
1082 | int saved_window; | |
1083 | unsigned long flags; | |
1084 | ||
1085 | spin_lock_irqsave(&lp->window_lock, flags); | |
1086 | saved_window = inw(ioaddr + EL3_CMD) >> 13; | |
1087 | EL3WINDOW(4); | |
0fa0ee05 BH |
1088 | data->val_out = mdio_read(ioaddr, data->phy_id & 0x1f, |
1089 | data->reg_num & 0x1f); | |
1da177e4 LT |
1090 | EL3WINDOW(saved_window); |
1091 | spin_unlock_irqrestore(&lp->window_lock, flags); | |
1092 | return 0; | |
1093 | } | |
1094 | case SIOCSMIIREG: /* Write the specified MII register */ | |
1095 | { | |
1096 | int saved_window; | |
1097 | unsigned long flags; | |
1098 | ||
1da177e4 LT |
1099 | spin_lock_irqsave(&lp->window_lock, flags); |
1100 | saved_window = inw(ioaddr + EL3_CMD) >> 13; | |
1101 | EL3WINDOW(4); | |
0fa0ee05 BH |
1102 | mdio_write(ioaddr, data->phy_id & 0x1f, |
1103 | data->reg_num & 0x1f, data->val_in); | |
1da177e4 LT |
1104 | EL3WINDOW(saved_window); |
1105 | spin_unlock_irqrestore(&lp->window_lock, flags); | |
1106 | return 0; | |
1107 | } | |
1108 | default: | |
1109 | return -EOPNOTSUPP; | |
1110 | } | |
1111 | } | |
1112 | ||
1113 | /* The Odie chip has a 64 bin multicast filter, but the bit layout is not | |
1114 | documented. Until it is we revert to receiving all multicast frames when | |
1115 | any multicast reception is desired. | |
1116 | Note: My other drivers emit a log message whenever promiscuous mode is | |
1117 | entered to help detect password sniffers. This is less desirable on | |
1118 | typical PC card machines, so we omit the message. | |
1119 | */ | |
1120 | ||
1121 | static void set_rx_mode(struct net_device *dev) | |
1122 | { | |
906da809 | 1123 | unsigned int ioaddr = dev->base_addr; |
1da177e4 LT |
1124 | |
1125 | if (dev->flags & IFF_PROMISC) | |
1126 | outw(SetRxFilter | RxStation | RxMulticast | RxBroadcast | RxProm, | |
1127 | ioaddr + EL3_CMD); | |
4cd24eaf | 1128 | else if (!netdev_mc_empty(dev) || (dev->flags & IFF_ALLMULTI)) |
1da177e4 LT |
1129 | outw(SetRxFilter|RxStation|RxMulticast|RxBroadcast, ioaddr + EL3_CMD); |
1130 | else | |
1131 | outw(SetRxFilter | RxStation | RxBroadcast, ioaddr + EL3_CMD); | |
1132 | } | |
1133 | ||
e3eef534 KK |
1134 | static void set_multicast_list(struct net_device *dev) |
1135 | { | |
1136 | struct el3_private *lp = netdev_priv(dev); | |
1137 | unsigned long flags; | |
1138 | ||
1139 | spin_lock_irqsave(&lp->window_lock, flags); | |
1140 | set_rx_mode(dev); | |
1141 | spin_unlock_irqrestore(&lp->window_lock, flags); | |
1142 | } | |
1143 | ||
1da177e4 LT |
1144 | static int el3_close(struct net_device *dev) |
1145 | { | |
906da809 | 1146 | unsigned int ioaddr = dev->base_addr; |
1da177e4 | 1147 | struct el3_private *lp = netdev_priv(dev); |
fba395ee | 1148 | struct pcmcia_device *link = lp->p_dev; |
1da177e4 | 1149 | |
dd0fab5b | 1150 | dev_dbg(&link->dev, "%s: shutting down ethercard.\n", dev->name); |
1da177e4 | 1151 | |
9940ec36 | 1152 | if (pcmcia_dev_present(link)) { |
1da177e4 LT |
1153 | unsigned long flags; |
1154 | ||
1155 | /* Turn off statistics ASAP. We update lp->stats below. */ | |
1156 | outw(StatsDisable, ioaddr + EL3_CMD); | |
1157 | ||
1158 | /* Disable the receiver and transmitter. */ | |
1159 | outw(RxDisable, ioaddr + EL3_CMD); | |
1160 | outw(TxDisable, ioaddr + EL3_CMD); | |
1161 | ||
1162 | /* Note: Switching to window 0 may disable the IRQ. */ | |
1163 | EL3WINDOW(0); | |
1164 | spin_lock_irqsave(&lp->window_lock, flags); | |
1165 | update_stats(dev); | |
1166 | spin_unlock_irqrestore(&lp->window_lock, flags); | |
b9a6eaff DR |
1167 | |
1168 | /* force interrupts off */ | |
1169 | outw(SetIntrEnb | 0x0000, ioaddr + EL3_CMD); | |
1da177e4 LT |
1170 | } |
1171 | ||
1172 | link->open--; | |
1173 | netif_stop_queue(dev); | |
1174 | del_timer_sync(&lp->media); | |
1175 | ||
1176 | return 0; | |
1177 | } | |
1178 | ||
270b6e94 DB |
1179 | static struct pcmcia_device_id tc574_ids[] = { |
1180 | PCMCIA_DEVICE_MANF_CARD(0x0101, 0x0574), | |
f0a3a153 | 1181 | PCMCIA_MFC_DEVICE_CIS_MANF_CARD(0, 0x0101, 0x0556, "cis/3CCFEM556.cis"), |
270b6e94 DB |
1182 | PCMCIA_DEVICE_NULL, |
1183 | }; | |
1184 | MODULE_DEVICE_TABLE(pcmcia, tc574_ids); | |
1185 | ||
1da177e4 LT |
1186 | static struct pcmcia_driver tc574_driver = { |
1187 | .owner = THIS_MODULE, | |
1188 | .drv = { | |
1189 | .name = "3c574_cs", | |
1190 | }, | |
15b99ac1 | 1191 | .probe = tc574_probe, |
cc3b4866 | 1192 | .remove = tc574_detach, |
270b6e94 | 1193 | .id_table = tc574_ids, |
98e4c28b DB |
1194 | .suspend = tc574_suspend, |
1195 | .resume = tc574_resume, | |
1da177e4 LT |
1196 | }; |
1197 | ||
1198 | static int __init init_tc574(void) | |
1199 | { | |
1200 | return pcmcia_register_driver(&tc574_driver); | |
1201 | } | |
1202 | ||
1203 | static void __exit exit_tc574(void) | |
1204 | { | |
1205 | pcmcia_unregister_driver(&tc574_driver); | |
1da177e4 LT |
1206 | } |
1207 | ||
1208 | module_init(init_tc574); | |
1209 | module_exit(exit_tc574); |