Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /*====================================================================== |
2 | ||
3 | A PCMCIA ethernet driver for Asix AX88190-based cards | |
4 | ||
5 | The Asix AX88190 is a NS8390-derived chipset with a few nasty | |
6 | idiosyncracies that make it very inconvenient to support with a | |
7 | standard 8390 driver. This driver is based on pcnet_cs, with the | |
8 | tweaked 8390 code grafted on the end. Much of what I did was to | |
9 | clean up and update a similar driver supplied by Asix, which was | |
10 | adapted by William Lee, william@asix.com.tw. | |
11 | ||
12 | Copyright (C) 2001 David A. Hinds -- dahinds@users.sourceforge.net | |
13 | ||
14 | axnet_cs.c 1.28 2002/06/29 06:27:37 | |
15 | ||
16 | The network driver code is based on Donald Becker's NE2000 code: | |
17 | ||
18 | Written 1992,1993 by Donald Becker. | |
19 | Copyright 1993 United States Government as represented by the | |
20 | Director, National Security Agency. This software may be used and | |
21 | distributed according to the terms of the GNU General Public License, | |
22 | incorporated herein by reference. | |
23 | Donald Becker may be reached at becker@scyld.com | |
24 | ||
25 | ======================================================================*/ | |
26 | ||
27 | #include <linux/kernel.h> | |
28 | #include <linux/module.h> | |
29 | #include <linux/init.h> | |
30 | #include <linux/ptrace.h> | |
31 | #include <linux/slab.h> | |
32 | #include <linux/string.h> | |
33 | #include <linux/timer.h> | |
34 | #include <linux/delay.h> | |
35 | #include <linux/spinlock.h> | |
36 | #include <linux/ethtool.h> | |
37 | #include <linux/netdevice.h> | |
3dd20516 | 38 | #include <linux/etherdevice.h> |
b8ab2dc3 | 39 | #include <linux/crc32.h> |
0fa0ee05 | 40 | #include <linux/mii.h> |
1da177e4 LT |
41 | #include "../8390.h" |
42 | ||
1da177e4 LT |
43 | #include <pcmcia/cs_types.h> |
44 | #include <pcmcia/cs.h> | |
45 | #include <pcmcia/cistpl.h> | |
46 | #include <pcmcia/ciscode.h> | |
47 | #include <pcmcia/ds.h> | |
48 | #include <pcmcia/cisreg.h> | |
49 | ||
50 | #include <asm/io.h> | |
51 | #include <asm/system.h> | |
52 | #include <asm/byteorder.h> | |
53 | #include <asm/uaccess.h> | |
54 | ||
55 | #define AXNET_CMD 0x00 | |
56 | #define AXNET_DATAPORT 0x10 /* NatSemi-defined port window offset. */ | |
57 | #define AXNET_RESET 0x1f /* Issue a read to reset, a write to clear. */ | |
58 | #define AXNET_MII_EEP 0x14 /* Offset of MII access port */ | |
59 | #define AXNET_TEST 0x15 /* Offset of TEST Register port */ | |
60 | #define AXNET_GPIO 0x17 /* Offset of General Purpose Register Port */ | |
61 | ||
62 | #define AXNET_START_PG 0x40 /* First page of TX buffer */ | |
63 | #define AXNET_STOP_PG 0x80 /* Last page +1 of RX ring */ | |
64 | ||
65 | #define AXNET_RDC_TIMEOUT 0x02 /* Max wait in jiffies for Tx RDC */ | |
66 | ||
67 | #define IS_AX88190 0x0001 | |
68 | #define IS_AX88790 0x0002 | |
69 | ||
70 | /*====================================================================*/ | |
71 | ||
72 | /* Module parameters */ | |
73 | ||
74 | MODULE_AUTHOR("David Hinds <dahinds@users.sourceforge.net>"); | |
75 | MODULE_DESCRIPTION("Asix AX88190 PCMCIA ethernet driver"); | |
76 | MODULE_LICENSE("GPL"); | |
77 | ||
1da177e4 LT |
78 | |
79 | /*====================================================================*/ | |
80 | ||
15b99ac1 | 81 | static int axnet_config(struct pcmcia_device *link); |
fba395ee | 82 | static void axnet_release(struct pcmcia_device *link); |
1da177e4 LT |
83 | static int axnet_open(struct net_device *dev); |
84 | static int axnet_close(struct net_device *dev); | |
85 | static int axnet_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); | |
dbf02fae SH |
86 | static netdev_tx_t axnet_start_xmit(struct sk_buff *skb, |
87 | struct net_device *dev); | |
3dd20516 SH |
88 | static struct net_device_stats *get_stats(struct net_device *dev); |
89 | static void set_multicast_list(struct net_device *dev); | |
90 | static void axnet_tx_timeout(struct net_device *dev); | |
7282d491 | 91 | static const struct ethtool_ops netdev_ethtool_ops; |
7d12e780 | 92 | static irqreturn_t ei_irq_wrapper(int irq, void *dev_id); |
1da177e4 LT |
93 | static void ei_watchdog(u_long arg); |
94 | static void axnet_reset_8390(struct net_device *dev); | |
95 | ||
906da809 OJ |
96 | static int mdio_read(unsigned int addr, int phy_id, int loc); |
97 | static void mdio_write(unsigned int addr, int phy_id, int loc, int value); | |
1da177e4 LT |
98 | |
99 | static void get_8390_hdr(struct net_device *, | |
100 | struct e8390_pkt_hdr *, int); | |
101 | static void block_input(struct net_device *dev, int count, | |
102 | struct sk_buff *skb, int ring_offset); | |
103 | static void block_output(struct net_device *dev, int count, | |
104 | const u_char *buf, const int start_page); | |
105 | ||
cc3b4866 | 106 | static void axnet_detach(struct pcmcia_device *p_dev); |
1da177e4 | 107 | |
1da177e4 LT |
108 | static void AX88190_init(struct net_device *dev, int startp); |
109 | static int ax_open(struct net_device *dev); | |
110 | static int ax_close(struct net_device *dev); | |
7d12e780 | 111 | static irqreturn_t ax_interrupt(int irq, void *dev_id); |
1da177e4 LT |
112 | |
113 | /*====================================================================*/ | |
114 | ||
115 | typedef struct axnet_dev_t { | |
fd238232 | 116 | struct pcmcia_device *p_dev; |
1da177e4 LT |
117 | dev_node_t node; |
118 | caddr_t base; | |
119 | struct timer_list watchdog; | |
120 | int stale, fast_poll; | |
121 | u_short link_status; | |
122 | u_char duplex_flag; | |
123 | int phy_id; | |
124 | int flags; | |
125 | } axnet_dev_t; | |
126 | ||
127 | static inline axnet_dev_t *PRIV(struct net_device *dev) | |
128 | { | |
129 | void *p = (char *)netdev_priv(dev) + sizeof(struct ei_device); | |
130 | return p; | |
131 | } | |
132 | ||
3dd20516 SH |
133 | static const struct net_device_ops axnet_netdev_ops = { |
134 | .ndo_open = axnet_open, | |
135 | .ndo_stop = axnet_close, | |
136 | .ndo_do_ioctl = axnet_ioctl, | |
137 | .ndo_start_xmit = axnet_start_xmit, | |
138 | .ndo_tx_timeout = axnet_tx_timeout, | |
139 | .ndo_get_stats = get_stats, | |
140 | .ndo_set_multicast_list = set_multicast_list, | |
141 | .ndo_change_mtu = eth_change_mtu, | |
142 | .ndo_set_mac_address = eth_mac_addr, | |
143 | .ndo_validate_addr = eth_validate_addr, | |
144 | }; | |
145 | ||
1da177e4 LT |
146 | /*====================================================================== |
147 | ||
148 | axnet_attach() creates an "instance" of the driver, allocating | |
149 | local data structures for one device. The device is registered | |
150 | with Card Services. | |
151 | ||
152 | ======================================================================*/ | |
153 | ||
15b99ac1 | 154 | static int axnet_probe(struct pcmcia_device *link) |
1da177e4 LT |
155 | { |
156 | axnet_dev_t *info; | |
1da177e4 | 157 | struct net_device *dev; |
3dd20516 | 158 | struct ei_device *ei_local; |
1da177e4 | 159 | |
dd0fab5b | 160 | dev_dbg(&link->dev, "axnet_attach()\n"); |
1da177e4 | 161 | |
3dd20516 | 162 | dev = alloc_etherdev(sizeof(struct ei_device) + sizeof(axnet_dev_t)); |
1da177e4 | 163 | if (!dev) |
f8cfa618 | 164 | return -ENOMEM; |
1da177e4 | 165 | |
3dd20516 SH |
166 | ei_local = netdev_priv(dev); |
167 | spin_lock_init(&ei_local->page_lock); | |
168 | ||
1da177e4 | 169 | info = PRIV(dev); |
fba395ee | 170 | info->p_dev = link; |
1da177e4 | 171 | link->priv = dev; |
5e7bf8cc | 172 | link->irq.Attributes = IRQ_TYPE_DYNAMIC_SHARING; |
1da177e4 LT |
173 | link->conf.Attributes = CONF_ENABLE_IRQ; |
174 | link->conf.IntType = INT_MEMORY_AND_IO; | |
175 | ||
3dd20516 SH |
176 | dev->netdev_ops = &axnet_netdev_ops; |
177 | ||
1da177e4 | 178 | SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops); |
3dd20516 | 179 | dev->watchdog_timeo = TX_TIMEOUT; |
1da177e4 | 180 | |
15b99ac1 | 181 | return axnet_config(link); |
1da177e4 LT |
182 | } /* axnet_attach */ |
183 | ||
184 | /*====================================================================== | |
185 | ||
186 | This deletes a driver "instance". The device is de-registered | |
187 | with Card Services. If it has been released, all local data | |
188 | structures are freed. Otherwise, the structures will be freed | |
189 | when the device is released. | |
190 | ||
191 | ======================================================================*/ | |
192 | ||
fba395ee | 193 | static void axnet_detach(struct pcmcia_device *link) |
1da177e4 LT |
194 | { |
195 | struct net_device *dev = link->priv; | |
1da177e4 | 196 | |
dd0fab5b | 197 | dev_dbg(&link->dev, "axnet_detach(0x%p)\n", link); |
1da177e4 | 198 | |
fd238232 | 199 | if (link->dev_node) |
1da177e4 LT |
200 | unregister_netdev(dev); |
201 | ||
e2d40963 | 202 | axnet_release(link); |
1da177e4 | 203 | |
1da177e4 LT |
204 | free_netdev(dev); |
205 | } /* axnet_detach */ | |
206 | ||
207 | /*====================================================================== | |
208 | ||
209 | This probes for a card's hardware address by reading the PROM. | |
210 | ||
211 | ======================================================================*/ | |
212 | ||
fba395ee | 213 | static int get_prom(struct pcmcia_device *link) |
1da177e4 LT |
214 | { |
215 | struct net_device *dev = link->priv; | |
906da809 | 216 | unsigned int ioaddr = dev->base_addr; |
1da177e4 LT |
217 | int i, j; |
218 | ||
219 | /* This is based on drivers/net/ne.c */ | |
220 | struct { | |
221 | u_char value, offset; | |
222 | } program_seq[] = { | |
223 | {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/ | |
224 | {0x01, EN0_DCFG}, /* Set word-wide access. */ | |
225 | {0x00, EN0_RCNTLO}, /* Clear the count regs. */ | |
226 | {0x00, EN0_RCNTHI}, | |
227 | {0x00, EN0_IMR}, /* Mask completion irq. */ | |
228 | {0xFF, EN0_ISR}, | |
229 | {E8390_RXOFF|0x40, EN0_RXCR}, /* 0x60 Set to monitor */ | |
230 | {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */ | |
231 | {0x10, EN0_RCNTLO}, | |
232 | {0x00, EN0_RCNTHI}, | |
233 | {0x00, EN0_RSARLO}, /* DMA starting at 0x0400. */ | |
234 | {0x04, EN0_RSARHI}, | |
235 | {E8390_RREAD+E8390_START, E8390_CMD}, | |
236 | }; | |
237 | ||
238 | /* Not much of a test, but the alternatives are messy */ | |
239 | if (link->conf.ConfigBase != 0x03c0) | |
240 | return 0; | |
241 | ||
242 | axnet_reset_8390(dev); | |
243 | mdelay(10); | |
244 | ||
ff8ac609 | 245 | for (i = 0; i < ARRAY_SIZE(program_seq); i++) |
1da177e4 LT |
246 | outb_p(program_seq[i].value, ioaddr + program_seq[i].offset); |
247 | ||
248 | for (i = 0; i < 6; i += 2) { | |
249 | j = inw(ioaddr + AXNET_DATAPORT); | |
250 | dev->dev_addr[i] = j & 0xff; | |
251 | dev->dev_addr[i+1] = j >> 8; | |
252 | } | |
253 | return 1; | |
254 | } /* get_prom */ | |
255 | ||
256 | /*====================================================================== | |
257 | ||
258 | axnet_config() is scheduled to run after a CARD_INSERTION event | |
259 | is received, to configure the PCMCIA socket, and to make the | |
260 | ethernet device available to the system. | |
261 | ||
262 | ======================================================================*/ | |
263 | ||
fba395ee | 264 | static int try_io_port(struct pcmcia_device *link) |
1da177e4 LT |
265 | { |
266 | int j, ret; | |
267 | if (link->io.NumPorts1 == 32) { | |
268 | link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; | |
269 | if (link->io.NumPorts2 > 0) { | |
270 | /* for master/slave multifunction cards */ | |
271 | link->io.Attributes2 = IO_DATA_PATH_WIDTH_8; | |
4c89e88b | 272 | link->irq.Attributes = |
e15c1c1f | 273 | IRQ_TYPE_DYNAMIC_SHARING; |
1da177e4 LT |
274 | } |
275 | } else { | |
276 | /* This should be two 16-port windows */ | |
277 | link->io.Attributes1 = IO_DATA_PATH_WIDTH_8; | |
278 | link->io.Attributes2 = IO_DATA_PATH_WIDTH_16; | |
279 | } | |
280 | if (link->io.BasePort1 == 0) { | |
281 | link->io.IOAddrLines = 16; | |
282 | for (j = 0; j < 0x400; j += 0x20) { | |
283 | link->io.BasePort1 = j ^ 0x300; | |
284 | link->io.BasePort2 = (j ^ 0x300) + 0x10; | |
fba395ee | 285 | ret = pcmcia_request_io(link, &link->io); |
4c89e88b DB |
286 | if (ret == 0) |
287 | return ret; | |
1da177e4 LT |
288 | } |
289 | return ret; | |
290 | } else { | |
fba395ee | 291 | return pcmcia_request_io(link, &link->io); |
1da177e4 LT |
292 | } |
293 | } | |
294 | ||
b54bf94b DB |
295 | static int axnet_configcheck(struct pcmcia_device *p_dev, |
296 | cistpl_cftable_entry_t *cfg, | |
8e2fc39d | 297 | cistpl_cftable_entry_t *dflt, |
ad913c11 | 298 | unsigned int vcc, |
b54bf94b DB |
299 | void *priv_data) |
300 | { | |
301 | int i; | |
302 | cistpl_io_t *io = &cfg->io; | |
303 | ||
304 | if (cfg->index == 0 || cfg->io.nwin == 0) | |
305 | return -ENODEV; | |
306 | ||
307 | p_dev->conf.ConfigIndex = 0x05; | |
308 | /* For multifunction cards, by convention, we configure the | |
309 | network function with window 0, and serial with window 1 */ | |
310 | if (io->nwin > 1) { | |
311 | i = (io->win[1].len > io->win[0].len); | |
312 | p_dev->io.BasePort2 = io->win[1-i].base; | |
313 | p_dev->io.NumPorts2 = io->win[1-i].len; | |
314 | } else { | |
315 | i = p_dev->io.NumPorts2 = 0; | |
316 | } | |
317 | p_dev->io.BasePort1 = io->win[i].base; | |
318 | p_dev->io.NumPorts1 = io->win[i].len; | |
319 | p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK; | |
320 | if (p_dev->io.NumPorts1 + p_dev->io.NumPorts2 >= 32) | |
321 | return try_io_port(p_dev); | |
322 | ||
323 | return -ENODEV; | |
324 | } | |
325 | ||
15b99ac1 | 326 | static int axnet_config(struct pcmcia_device *link) |
1da177e4 | 327 | { |
1da177e4 LT |
328 | struct net_device *dev = link->priv; |
329 | axnet_dev_t *info = PRIV(dev); | |
dd0fab5b | 330 | int i, j, j2, ret; |
1da177e4 | 331 | |
dd0fab5b | 332 | dev_dbg(&link->dev, "axnet_config(0x%p)\n", link); |
1da177e4 | 333 | |
1da177e4 LT |
334 | /* don't trust the CIS on this; Linksys got it wrong */ |
335 | link->conf.Present = 0x63; | |
dd0fab5b DB |
336 | ret = pcmcia_loop_config(link, axnet_configcheck, NULL); |
337 | if (ret != 0) | |
1da177e4 | 338 | goto failed; |
1da177e4 | 339 | |
dd0fab5b DB |
340 | ret = pcmcia_request_irq(link, &link->irq); |
341 | if (ret) | |
342 | goto failed; | |
1da177e4 LT |
343 | |
344 | if (link->io.NumPorts2 == 8) { | |
345 | link->conf.Attributes |= CONF_ENABLE_SPKR; | |
346 | link->conf.Status = CCSR_AUDIO_ENA; | |
347 | } | |
348 | ||
dd0fab5b DB |
349 | ret = pcmcia_request_configuration(link, &link->conf); |
350 | if (ret) | |
351 | goto failed; | |
352 | ||
1da177e4 LT |
353 | dev->irq = link->irq.AssignedIRQ; |
354 | dev->base_addr = link->io.BasePort1; | |
355 | ||
356 | if (!get_prom(link)) { | |
357 | printk(KERN_NOTICE "axnet_cs: this is not an AX88190 card!\n"); | |
358 | printk(KERN_NOTICE "axnet_cs: use pcnet_cs instead.\n"); | |
359 | goto failed; | |
360 | } | |
361 | ||
362 | ei_status.name = "AX88190"; | |
363 | ei_status.word16 = 1; | |
364 | ei_status.tx_start_page = AXNET_START_PG; | |
365 | ei_status.rx_start_page = AXNET_START_PG + TX_PAGES; | |
366 | ei_status.stop_page = AXNET_STOP_PG; | |
367 | ei_status.reset_8390 = &axnet_reset_8390; | |
368 | ei_status.get_8390_hdr = &get_8390_hdr; | |
369 | ei_status.block_input = &block_input; | |
370 | ei_status.block_output = &block_output; | |
371 | ||
372 | if (inb(dev->base_addr + AXNET_TEST) != 0) | |
373 | info->flags |= IS_AX88790; | |
374 | else | |
375 | info->flags |= IS_AX88190; | |
376 | ||
377 | if (info->flags & IS_AX88790) | |
378 | outb(0x10, dev->base_addr + AXNET_GPIO); /* select Internal PHY */ | |
379 | ||
380 | for (i = 0; i < 32; i++) { | |
381 | j = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 1); | |
ad3620a0 KK |
382 | j2 = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 2); |
383 | if (j == j2) continue; | |
1da177e4 LT |
384 | if ((j != 0) && (j != 0xffff)) break; |
385 | } | |
386 | ||
387 | /* Maybe PHY is in power down mode. (PPD_SET = 1) | |
388 | Bit 2 of CCSR is active low. */ | |
389 | if (i == 32) { | |
390 | conf_reg_t reg = { 0, CS_WRITE, CISREG_CCSR, 0x04 }; | |
fba395ee | 391 | pcmcia_access_configuration_register(link, ®); |
1da177e4 LT |
392 | for (i = 0; i < 32; i++) { |
393 | j = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 1); | |
ad3620a0 KK |
394 | j2 = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 2); |
395 | if (j == j2) continue; | |
1da177e4 LT |
396 | if ((j != 0) && (j != 0xffff)) break; |
397 | } | |
398 | } | |
399 | ||
400 | info->phy_id = (i < 32) ? i : -1; | |
fd238232 | 401 | link->dev_node = &info->node; |
dd2e5a15 | 402 | SET_NETDEV_DEV(dev, &link->dev); |
1da177e4 LT |
403 | |
404 | if (register_netdev(dev) != 0) { | |
405 | printk(KERN_NOTICE "axnet_cs: register_netdev() failed\n"); | |
fd238232 | 406 | link->dev_node = NULL; |
1da177e4 LT |
407 | goto failed; |
408 | } | |
409 | ||
410 | strcpy(info->node.dev_name, dev->name); | |
411 | ||
0795af57 | 412 | printk(KERN_INFO "%s: Asix AX88%d90: io %#3lx, irq %d, " |
e174961c | 413 | "hw_addr %pM\n", |
1da177e4 | 414 | dev->name, ((info->flags & IS_AX88790) ? 7 : 1), |
0795af57 | 415 | dev->base_addr, dev->irq, |
e174961c | 416 | dev->dev_addr); |
1da177e4 | 417 | if (info->phy_id != -1) { |
dd0fab5b | 418 | dev_dbg(&link->dev, " MII transceiver at index %d, status %x.\n", info->phy_id, j); |
1da177e4 LT |
419 | } else { |
420 | printk(KERN_NOTICE " No MII transceivers found!\n"); | |
421 | } | |
15b99ac1 | 422 | return 0; |
1da177e4 | 423 | |
1da177e4 LT |
424 | failed: |
425 | axnet_release(link); | |
15b99ac1 | 426 | return -ENODEV; |
1da177e4 LT |
427 | } /* axnet_config */ |
428 | ||
429 | /*====================================================================== | |
430 | ||
431 | After a card is removed, axnet_release() will unregister the net | |
432 | device, and release the PCMCIA configuration. If the device is | |
433 | still open, this will be postponed until it is closed. | |
434 | ||
435 | ======================================================================*/ | |
436 | ||
fba395ee | 437 | static void axnet_release(struct pcmcia_device *link) |
1da177e4 | 438 | { |
fba395ee | 439 | pcmcia_disable_device(link); |
1da177e4 LT |
440 | } |
441 | ||
fba395ee | 442 | static int axnet_suspend(struct pcmcia_device *link) |
98e4c28b | 443 | { |
98e4c28b DB |
444 | struct net_device *dev = link->priv; |
445 | ||
e2d40963 DB |
446 | if (link->open) |
447 | netif_device_detach(dev); | |
98e4c28b DB |
448 | |
449 | return 0; | |
450 | } | |
451 | ||
fba395ee | 452 | static int axnet_resume(struct pcmcia_device *link) |
98e4c28b | 453 | { |
98e4c28b DB |
454 | struct net_device *dev = link->priv; |
455 | ||
e2d40963 | 456 | if (link->open) { |
8661bb5b DB |
457 | axnet_reset_8390(dev); |
458 | AX88190_init(dev, 1); | |
459 | netif_device_attach(dev); | |
98e4c28b DB |
460 | } |
461 | ||
462 | return 0; | |
463 | } | |
464 | ||
465 | ||
1da177e4 LT |
466 | /*====================================================================== |
467 | ||
468 | MII interface support | |
469 | ||
470 | ======================================================================*/ | |
471 | ||
472 | #define MDIO_SHIFT_CLK 0x01 | |
473 | #define MDIO_DATA_WRITE0 0x00 | |
474 | #define MDIO_DATA_WRITE1 0x08 | |
475 | #define MDIO_DATA_READ 0x04 | |
476 | #define MDIO_MASK 0x0f | |
477 | #define MDIO_ENB_IN 0x02 | |
478 | ||
906da809 | 479 | static void mdio_sync(unsigned int addr) |
1da177e4 LT |
480 | { |
481 | int bits; | |
482 | for (bits = 0; bits < 32; bits++) { | |
483 | outb_p(MDIO_DATA_WRITE1, addr); | |
484 | outb_p(MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, addr); | |
485 | } | |
486 | } | |
487 | ||
906da809 | 488 | static int mdio_read(unsigned int addr, int phy_id, int loc) |
1da177e4 LT |
489 | { |
490 | u_int cmd = (0xf6<<10)|(phy_id<<5)|loc; | |
491 | int i, retval = 0; | |
492 | ||
493 | mdio_sync(addr); | |
494 | for (i = 14; i >= 0; i--) { | |
495 | int dat = (cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0; | |
496 | outb_p(dat, addr); | |
497 | outb_p(dat | MDIO_SHIFT_CLK, addr); | |
498 | } | |
499 | for (i = 19; i > 0; i--) { | |
500 | outb_p(MDIO_ENB_IN, addr); | |
501 | retval = (retval << 1) | ((inb_p(addr) & MDIO_DATA_READ) != 0); | |
502 | outb_p(MDIO_ENB_IN | MDIO_SHIFT_CLK, addr); | |
503 | } | |
504 | return (retval>>1) & 0xffff; | |
505 | } | |
506 | ||
906da809 | 507 | static void mdio_write(unsigned int addr, int phy_id, int loc, int value) |
1da177e4 LT |
508 | { |
509 | u_int cmd = (0x05<<28)|(phy_id<<23)|(loc<<18)|(1<<17)|value; | |
510 | int i; | |
511 | ||
512 | mdio_sync(addr); | |
513 | for (i = 31; i >= 0; i--) { | |
514 | int dat = (cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0; | |
515 | outb_p(dat, addr); | |
516 | outb_p(dat | MDIO_SHIFT_CLK, addr); | |
517 | } | |
518 | for (i = 1; i >= 0; i--) { | |
519 | outb_p(MDIO_ENB_IN, addr); | |
520 | outb_p(MDIO_ENB_IN | MDIO_SHIFT_CLK, addr); | |
521 | } | |
522 | } | |
523 | ||
524 | /*====================================================================*/ | |
525 | ||
526 | static int axnet_open(struct net_device *dev) | |
527 | { | |
59b34c12 | 528 | int ret; |
1da177e4 | 529 | axnet_dev_t *info = PRIV(dev); |
fba395ee | 530 | struct pcmcia_device *link = info->p_dev; |
54299ef7 | 531 | unsigned int nic_base = dev->base_addr; |
1da177e4 | 532 | |
dd0fab5b | 533 | dev_dbg(&link->dev, "axnet_open('%s')\n", dev->name); |
1da177e4 | 534 | |
9940ec36 | 535 | if (!pcmcia_dev_present(link)) |
1da177e4 LT |
536 | return -ENODEV; |
537 | ||
54299ef7 | 538 | outb_p(0xFF, nic_base + EN0_ISR); /* Clear bogus intr. */ |
59b34c12 YY |
539 | ret = request_irq(dev->irq, ei_irq_wrapper, IRQF_SHARED, "axnet_cs", dev); |
540 | if (ret) | |
541 | return ret; | |
1da177e4 | 542 | |
59b34c12 | 543 | link->open++; |
1da177e4 LT |
544 | |
545 | info->link_status = 0x00; | |
546 | init_timer(&info->watchdog); | |
547 | info->watchdog.function = &ei_watchdog; | |
548 | info->watchdog.data = (u_long)dev; | |
549 | info->watchdog.expires = jiffies + HZ; | |
550 | add_timer(&info->watchdog); | |
551 | ||
552 | return ax_open(dev); | |
553 | } /* axnet_open */ | |
554 | ||
555 | /*====================================================================*/ | |
556 | ||
557 | static int axnet_close(struct net_device *dev) | |
558 | { | |
559 | axnet_dev_t *info = PRIV(dev); | |
fba395ee | 560 | struct pcmcia_device *link = info->p_dev; |
1da177e4 | 561 | |
dd0fab5b | 562 | dev_dbg(&link->dev, "axnet_close('%s')\n", dev->name); |
1da177e4 LT |
563 | |
564 | ax_close(dev); | |
565 | free_irq(dev->irq, dev); | |
566 | ||
567 | link->open--; | |
568 | netif_stop_queue(dev); | |
569 | del_timer_sync(&info->watchdog); | |
570 | ||
571 | return 0; | |
572 | } /* axnet_close */ | |
573 | ||
574 | /*====================================================================== | |
575 | ||
576 | Hard reset the card. This used to pause for the same period that | |
577 | a 8390 reset command required, but that shouldn't be necessary. | |
578 | ||
579 | ======================================================================*/ | |
580 | ||
581 | static void axnet_reset_8390(struct net_device *dev) | |
582 | { | |
906da809 | 583 | unsigned int nic_base = dev->base_addr; |
1da177e4 LT |
584 | int i; |
585 | ||
586 | ei_status.txing = ei_status.dmaing = 0; | |
587 | ||
588 | outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, nic_base + E8390_CMD); | |
589 | ||
590 | outb(inb(nic_base + AXNET_RESET), nic_base + AXNET_RESET); | |
591 | ||
592 | for (i = 0; i < 100; i++) { | |
593 | if ((inb_p(nic_base+EN0_ISR) & ENISR_RESET) != 0) | |
594 | break; | |
595 | udelay(100); | |
596 | } | |
597 | outb_p(ENISR_RESET, nic_base + EN0_ISR); /* Ack intr. */ | |
598 | ||
599 | if (i == 100) | |
600 | printk(KERN_ERR "%s: axnet_reset_8390() did not complete.\n", | |
601 | dev->name); | |
602 | ||
603 | } /* axnet_reset_8390 */ | |
604 | ||
605 | /*====================================================================*/ | |
606 | ||
7d12e780 | 607 | static irqreturn_t ei_irq_wrapper(int irq, void *dev_id) |
1da177e4 LT |
608 | { |
609 | struct net_device *dev = dev_id; | |
610 | PRIV(dev)->stale = 0; | |
7d12e780 | 611 | return ax_interrupt(irq, dev_id); |
1da177e4 LT |
612 | } |
613 | ||
614 | static void ei_watchdog(u_long arg) | |
615 | { | |
616 | struct net_device *dev = (struct net_device *)(arg); | |
617 | axnet_dev_t *info = PRIV(dev); | |
906da809 OJ |
618 | unsigned int nic_base = dev->base_addr; |
619 | unsigned int mii_addr = nic_base + AXNET_MII_EEP; | |
1da177e4 LT |
620 | u_short link; |
621 | ||
622 | if (!netif_device_present(dev)) goto reschedule; | |
623 | ||
624 | /* Check for pending interrupt with expired latency timer: with | |
625 | this, we can limp along even if the interrupt is blocked */ | |
626 | if (info->stale++ && (inb_p(nic_base + EN0_ISR) & ENISR_ALL)) { | |
627 | if (!info->fast_poll) | |
628 | printk(KERN_INFO "%s: interrupt(s) dropped!\n", dev->name); | |
7d12e780 | 629 | ei_irq_wrapper(dev->irq, dev); |
1da177e4 LT |
630 | info->fast_poll = HZ; |
631 | } | |
632 | if (info->fast_poll) { | |
633 | info->fast_poll--; | |
634 | info->watchdog.expires = jiffies + 1; | |
635 | add_timer(&info->watchdog); | |
636 | return; | |
637 | } | |
638 | ||
639 | if (info->phy_id < 0) | |
640 | goto reschedule; | |
641 | link = mdio_read(mii_addr, info->phy_id, 1); | |
642 | if (!link || (link == 0xffff)) { | |
643 | printk(KERN_INFO "%s: MII is missing!\n", dev->name); | |
644 | info->phy_id = -1; | |
645 | goto reschedule; | |
646 | } | |
647 | ||
648 | link &= 0x0004; | |
649 | if (link != info->link_status) { | |
650 | u_short p = mdio_read(mii_addr, info->phy_id, 5); | |
651 | printk(KERN_INFO "%s: %s link beat\n", dev->name, | |
652 | (link) ? "found" : "lost"); | |
653 | if (link) { | |
654 | info->duplex_flag = (p & 0x0140) ? 0x80 : 0x00; | |
655 | if (p) | |
656 | printk(KERN_INFO "%s: autonegotiation complete: " | |
657 | "%sbaseT-%cD selected\n", dev->name, | |
658 | ((p & 0x0180) ? "100" : "10"), | |
659 | ((p & 0x0140) ? 'F' : 'H')); | |
660 | else | |
661 | printk(KERN_INFO "%s: link partner did not autonegotiate\n", | |
662 | dev->name); | |
663 | AX88190_init(dev, 1); | |
664 | } | |
665 | info->link_status = link; | |
666 | } | |
667 | ||
668 | reschedule: | |
669 | info->watchdog.expires = jiffies + HZ; | |
670 | add_timer(&info->watchdog); | |
671 | } | |
672 | ||
673 | static void netdev_get_drvinfo(struct net_device *dev, | |
674 | struct ethtool_drvinfo *info) | |
675 | { | |
676 | strcpy(info->driver, "axnet_cs"); | |
677 | } | |
678 | ||
7282d491 | 679 | static const struct ethtool_ops netdev_ethtool_ops = { |
1da177e4 LT |
680 | .get_drvinfo = netdev_get_drvinfo, |
681 | }; | |
682 | ||
683 | /*====================================================================*/ | |
684 | ||
685 | static int axnet_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) | |
686 | { | |
687 | axnet_dev_t *info = PRIV(dev); | |
0fa0ee05 | 688 | struct mii_ioctl_data *data = if_mii(rq); |
906da809 | 689 | unsigned int mii_addr = dev->base_addr + AXNET_MII_EEP; |
1da177e4 LT |
690 | switch (cmd) { |
691 | case SIOCGMIIPHY: | |
0fa0ee05 | 692 | data->phy_id = info->phy_id; |
1da177e4 | 693 | case SIOCGMIIREG: /* Read MII PHY register. */ |
0fa0ee05 | 694 | data->val_out = mdio_read(mii_addr, data->phy_id, data->reg_num & 0x1f); |
1da177e4 LT |
695 | return 0; |
696 | case SIOCSMIIREG: /* Write MII PHY register. */ | |
0fa0ee05 | 697 | mdio_write(mii_addr, data->phy_id, data->reg_num & 0x1f, data->val_in); |
1da177e4 LT |
698 | return 0; |
699 | } | |
700 | return -EOPNOTSUPP; | |
701 | } | |
702 | ||
703 | /*====================================================================*/ | |
704 | ||
705 | static void get_8390_hdr(struct net_device *dev, | |
706 | struct e8390_pkt_hdr *hdr, | |
707 | int ring_page) | |
708 | { | |
906da809 | 709 | unsigned int nic_base = dev->base_addr; |
1da177e4 LT |
710 | |
711 | outb_p(0, nic_base + EN0_RSARLO); /* On page boundary */ | |
712 | outb_p(ring_page, nic_base + EN0_RSARHI); | |
713 | outb_p(E8390_RREAD+E8390_START, nic_base + AXNET_CMD); | |
714 | ||
715 | insw(nic_base + AXNET_DATAPORT, hdr, | |
716 | sizeof(struct e8390_pkt_hdr)>>1); | |
717 | /* Fix for big endian systems */ | |
718 | hdr->count = le16_to_cpu(hdr->count); | |
719 | ||
720 | } | |
721 | ||
722 | /*====================================================================*/ | |
723 | ||
724 | static void block_input(struct net_device *dev, int count, | |
725 | struct sk_buff *skb, int ring_offset) | |
726 | { | |
906da809 | 727 | unsigned int nic_base = dev->base_addr; |
1da177e4 LT |
728 | int xfer_count = count; |
729 | char *buf = skb->data; | |
730 | ||
1da177e4 | 731 | if ((ei_debug > 4) && (count != 4)) |
dd0fab5b | 732 | pr_debug("%s: [bi=%d]\n", dev->name, count+4); |
1da177e4 LT |
733 | outb_p(ring_offset & 0xff, nic_base + EN0_RSARLO); |
734 | outb_p(ring_offset >> 8, nic_base + EN0_RSARHI); | |
735 | outb_p(E8390_RREAD+E8390_START, nic_base + AXNET_CMD); | |
736 | ||
737 | insw(nic_base + AXNET_DATAPORT,buf,count>>1); | |
738 | if (count & 0x01) | |
739 | buf[count-1] = inb(nic_base + AXNET_DATAPORT), xfer_count++; | |
740 | ||
741 | } | |
742 | ||
743 | /*====================================================================*/ | |
744 | ||
745 | static void block_output(struct net_device *dev, int count, | |
746 | const u_char *buf, const int start_page) | |
747 | { | |
906da809 | 748 | unsigned int nic_base = dev->base_addr; |
1da177e4 | 749 | |
dd0fab5b | 750 | pr_debug("%s: [bo=%d]\n", dev->name, count); |
1da177e4 LT |
751 | |
752 | /* Round the count up for word writes. Do we need to do this? | |
753 | What effect will an odd byte count have on the 8390? | |
754 | I should check someday. */ | |
755 | if (count & 0x01) | |
756 | count++; | |
757 | ||
758 | outb_p(0x00, nic_base + EN0_RSARLO); | |
759 | outb_p(start_page, nic_base + EN0_RSARHI); | |
760 | outb_p(E8390_RWRITE+E8390_START, nic_base + AXNET_CMD); | |
761 | outsw(nic_base + AXNET_DATAPORT, buf, count>>1); | |
762 | } | |
763 | ||
c414f755 DB |
764 | static struct pcmcia_device_id axnet_ids[] = { |
765 | PCMCIA_PFC_DEVICE_MANF_CARD(0, 0x016c, 0x0081), | |
766 | PCMCIA_DEVICE_MANF_CARD(0x018a, 0x0301), | |
767 | PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0301), | |
768 | PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0303), | |
769 | PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0309), | |
770 | PCMCIA_DEVICE_MANF_CARD(0x0274, 0x1106), | |
771 | PCMCIA_DEVICE_MANF_CARD(0x8a01, 0xc1ab), | |
c67eebd6 | 772 | PCMCIA_DEVICE_MANF_CARD(0x021b, 0x0202), |
dad8c737 | 773 | PCMCIA_DEVICE_MANF_CARD(0xffff, 0x1090), |
2fe22a8b | 774 | PCMCIA_DEVICE_PROD_ID12("AmbiCom,Inc.", "Fast Ethernet PC Card(AMB8110)", 0x49b020a7, 0x119cc9fc), |
c414f755 DB |
775 | PCMCIA_DEVICE_PROD_ID124("Fast Ethernet", "16-bit PC Card", "AX88190", 0xb4be14e3, 0x9a12eb6a, 0xab9be5ef), |
776 | PCMCIA_DEVICE_PROD_ID12("ASIX", "AX88190", 0x0959823b, 0xab9be5ef), | |
777 | PCMCIA_DEVICE_PROD_ID12("Billionton", "LNA-100B", 0x552ab682, 0xbc3b87e1), | |
778 | PCMCIA_DEVICE_PROD_ID12("CHEETAH ETHERCARD", "EN2228", 0x00fa7bc8, 0x00e990cc), | |
779 | PCMCIA_DEVICE_PROD_ID12("CNet", "CNF301", 0xbc477dde, 0x78c5f40b), | |
780 | PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega FEther PCC-TXD", 0x5261440f, 0x436768c5), | |
781 | PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega FEtherII PCC-TXD", 0x5261440f, 0x730df72e), | |
782 | PCMCIA_DEVICE_PROD_ID12("Dynalink", "L100C16", 0x55632fd5, 0x66bc2a90), | |
2dcc9ff7 | 783 | PCMCIA_DEVICE_PROD_ID12("IO DATA", "ETXPCM", 0x547e66dc, 0x233adac2), |
c414f755 DB |
784 | PCMCIA_DEVICE_PROD_ID12("Linksys", "EtherFast 10/100 PC Card (PCMPC100 V3)", 0x0733cc81, 0x232019a8), |
785 | PCMCIA_DEVICE_PROD_ID12("MELCO", "LPC3-TX", 0x481e0094, 0xf91af609), | |
208fbec5 | 786 | PCMCIA_DEVICE_PROD_ID12("NETGEAR", "FA411", 0x9aa79dc3, 0x40fad875), |
c414f755 DB |
787 | PCMCIA_DEVICE_PROD_ID12("PCMCIA", "100BASE", 0x281f1c5d, 0x7c2add04), |
788 | PCMCIA_DEVICE_PROD_ID12("PCMCIA", "FastEtherCard", 0x281f1c5d, 0x7ef26116), | |
789 | PCMCIA_DEVICE_PROD_ID12("PCMCIA", "FEP501", 0x281f1c5d, 0x2e272058), | |
790 | PCMCIA_DEVICE_PROD_ID14("Network Everywhere", "AX88190", 0x820a67b6, 0xab9be5ef), | |
c414f755 DB |
791 | PCMCIA_DEVICE_NULL, |
792 | }; | |
793 | MODULE_DEVICE_TABLE(pcmcia, axnet_ids); | |
794 | ||
1da177e4 LT |
795 | static struct pcmcia_driver axnet_cs_driver = { |
796 | .owner = THIS_MODULE, | |
797 | .drv = { | |
798 | .name = "axnet_cs", | |
799 | }, | |
15b99ac1 | 800 | .probe = axnet_probe, |
cc3b4866 | 801 | .remove = axnet_detach, |
c414f755 | 802 | .id_table = axnet_ids, |
98e4c28b DB |
803 | .suspend = axnet_suspend, |
804 | .resume = axnet_resume, | |
1da177e4 LT |
805 | }; |
806 | ||
807 | static int __init init_axnet_cs(void) | |
808 | { | |
809 | return pcmcia_register_driver(&axnet_cs_driver); | |
810 | } | |
811 | ||
812 | static void __exit exit_axnet_cs(void) | |
813 | { | |
814 | pcmcia_unregister_driver(&axnet_cs_driver); | |
1da177e4 LT |
815 | } |
816 | ||
817 | module_init(init_axnet_cs); | |
818 | module_exit(exit_axnet_cs); | |
819 | ||
820 | /*====================================================================*/ | |
821 | ||
822 | /* 8390.c: A general NS8390 ethernet driver core for linux. */ | |
823 | /* | |
824 | Written 1992-94 by Donald Becker. | |
825 | ||
826 | Copyright 1993 United States Government as represented by the | |
827 | Director, National Security Agency. | |
828 | ||
829 | This software may be used and distributed according to the terms | |
830 | of the GNU General Public License, incorporated herein by reference. | |
831 | ||
832 | The author may be reached as becker@scyld.com, or C/O | |
833 | Scyld Computing Corporation | |
834 | 410 Severn Ave., Suite 210 | |
835 | Annapolis MD 21403 | |
836 | ||
837 | This is the chip-specific code for many 8390-based ethernet adaptors. | |
838 | This is not a complete driver, it must be combined with board-specific | |
839 | code such as ne.c, wd.c, 3c503.c, etc. | |
840 | ||
841 | Seeing how at least eight drivers use this code, (not counting the | |
842 | PCMCIA ones either) it is easy to break some card by what seems like | |
843 | a simple innocent change. Please contact me or Donald if you think | |
844 | you have found something that needs changing. -- PG | |
845 | ||
846 | Changelog: | |
847 | ||
848 | Paul Gortmaker : remove set_bit lock, other cleanups. | |
849 | Paul Gortmaker : add ei_get_8390_hdr() so we can pass skb's to | |
850 | ei_block_input() for eth_io_copy_and_sum(). | |
851 | Paul Gortmaker : exchange static int ei_pingpong for a #define, | |
852 | also add better Tx error handling. | |
853 | Paul Gortmaker : rewrite Rx overrun handling as per NS specs. | |
854 | Alexey Kuznetsov : use the 8390's six bit hash multicast filter. | |
855 | Paul Gortmaker : tweak ANK's above multicast changes a bit. | |
856 | Paul Gortmaker : update packet statistics for v2.1.x | |
857 | Alan Cox : support arbitary stupid port mappings on the | |
858 | 68K Macintosh. Support >16bit I/O spaces | |
859 | Paul Gortmaker : add kmod support for auto-loading of the 8390 | |
860 | module by all drivers that require it. | |
861 | Alan Cox : Spinlocking work, added 'BUG_83C690' | |
862 | Paul Gortmaker : Separate out Tx timeout code from Tx path. | |
863 | ||
864 | Sources: | |
865 | The National Semiconductor LAN Databook, and the 3Com 3c503 databook. | |
866 | ||
867 | */ | |
868 | ||
6ae03851 | 869 | static const char version_8390[] = KERN_INFO \ |
1da177e4 LT |
870 | "8390.c:v1.10cvs 9/23/94 Donald Becker (becker@scyld.com)\n"; |
871 | ||
872 | #include <linux/bitops.h> | |
873 | #include <asm/irq.h> | |
874 | #include <linux/fcntl.h> | |
875 | #include <linux/in.h> | |
876 | #include <linux/interrupt.h> | |
877 | ||
1da177e4 LT |
878 | #define BUG_83C690 |
879 | ||
880 | /* These are the operational function interfaces to board-specific | |
881 | routines. | |
882 | void reset_8390(struct net_device *dev) | |
883 | Resets the board associated with DEV, including a hardware reset of | |
884 | the 8390. This is only called when there is a transmit timeout, and | |
885 | it is always followed by 8390_init(). | |
886 | void block_output(struct net_device *dev, int count, const unsigned char *buf, | |
887 | int start_page) | |
888 | Write the COUNT bytes of BUF to the packet buffer at START_PAGE. The | |
889 | "page" value uses the 8390's 256-byte pages. | |
890 | void get_8390_hdr(struct net_device *dev, struct e8390_hdr *hdr, int ring_page) | |
891 | Read the 4 byte, page aligned 8390 header. *If* there is a | |
892 | subsequent read, it will be of the rest of the packet. | |
893 | void block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset) | |
894 | Read COUNT bytes from the packet buffer into the skb data area. Start | |
895 | reading from RING_OFFSET, the address as the 8390 sees it. This will always | |
896 | follow the read of the 8390 header. | |
897 | */ | |
898 | #define ei_reset_8390 (ei_local->reset_8390) | |
899 | #define ei_block_output (ei_local->block_output) | |
900 | #define ei_block_input (ei_local->block_input) | |
901 | #define ei_get_8390_hdr (ei_local->get_8390_hdr) | |
902 | ||
903 | /* use 0 for production, 1 for verification, >2 for debug */ | |
904 | #ifndef ei_debug | |
905 | int ei_debug = 1; | |
906 | #endif | |
907 | ||
908 | /* Index to functions. */ | |
909 | static void ei_tx_intr(struct net_device *dev); | |
910 | static void ei_tx_err(struct net_device *dev); | |
1da177e4 LT |
911 | static void ei_receive(struct net_device *dev); |
912 | static void ei_rx_overrun(struct net_device *dev); | |
913 | ||
914 | /* Routines generic to NS8390-based boards. */ | |
915 | static void NS8390_trigger_send(struct net_device *dev, unsigned int length, | |
916 | int start_page); | |
1da177e4 LT |
917 | static void do_set_multicast_list(struct net_device *dev); |
918 | ||
919 | /* | |
920 | * SMP and the 8390 setup. | |
921 | * | |
922 | * The 8390 isnt exactly designed to be multithreaded on RX/TX. There is | |
923 | * a page register that controls bank and packet buffer access. We guard | |
924 | * this with ei_local->page_lock. Nobody should assume or set the page other | |
925 | * than zero when the lock is not held. Lock holders must restore page 0 | |
926 | * before unlocking. Even pure readers must take the lock to protect in | |
927 | * page 0. | |
928 | * | |
929 | * To make life difficult the chip can also be very slow. We therefore can't | |
930 | * just use spinlocks. For the longer lockups we disable the irq the device | |
931 | * sits on and hold the lock. We must hold the lock because there is a dual | |
932 | * processor case other than interrupts (get stats/set multicast list in | |
933 | * parallel with each other and transmit). | |
934 | * | |
935 | * Note: in theory we can just disable the irq on the card _but_ there is | |
936 | * a latency on SMP irq delivery. So we can easily go "disable irq" "sync irqs" | |
937 | * enter lock, take the queued irq. So we waddle instead of flying. | |
938 | * | |
939 | * Finally by special arrangement for the purpose of being generally | |
940 | * annoying the transmit function is called bh atomic. That places | |
941 | * restrictions on the user context callers as disable_irq won't save | |
942 | * them. | |
943 | */ | |
944 | ||
945 | /** | |
946 | * ax_open - Open/initialize the board. | |
947 | * @dev: network device to initialize | |
948 | * | |
949 | * This routine goes all-out, setting everything | |
950 | * up anew at each open, even though many of these registers should only | |
951 | * need to be set once at boot. | |
952 | */ | |
953 | static int ax_open(struct net_device *dev) | |
954 | { | |
955 | unsigned long flags; | |
956 | struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
957 | ||
1da177e4 LT |
958 | /* |
959 | * Grab the page lock so we own the register set, then call | |
960 | * the init function. | |
961 | */ | |
962 | ||
963 | spin_lock_irqsave(&ei_local->page_lock, flags); | |
964 | AX88190_init(dev, 1); | |
965 | /* Set the flag before we drop the lock, That way the IRQ arrives | |
966 | after its set and we get no silly warnings */ | |
967 | netif_start_queue(dev); | |
968 | spin_unlock_irqrestore(&ei_local->page_lock, flags); | |
969 | ei_local->irqlock = 0; | |
970 | return 0; | |
971 | } | |
972 | ||
973 | #define dev_lock(dev) (((struct ei_device *)netdev_priv(dev))->page_lock) | |
974 | ||
975 | /** | |
976 | * ax_close - shut down network device | |
977 | * @dev: network device to close | |
978 | * | |
979 | * Opposite of ax_open(). Only used when "ifconfig <devname> down" is done. | |
980 | */ | |
6b2e4386 | 981 | static int ax_close(struct net_device *dev) |
1da177e4 LT |
982 | { |
983 | unsigned long flags; | |
984 | ||
985 | /* | |
986 | * Hold the page lock during close | |
987 | */ | |
988 | ||
989 | spin_lock_irqsave(&dev_lock(dev), flags); | |
990 | AX88190_init(dev, 0); | |
991 | spin_unlock_irqrestore(&dev_lock(dev), flags); | |
992 | netif_stop_queue(dev); | |
993 | return 0; | |
994 | } | |
995 | ||
996 | /** | |
70eb1bfd | 997 | * axnet_tx_timeout - handle transmit time out condition |
1da177e4 LT |
998 | * @dev: network device which has apparently fallen asleep |
999 | * | |
1000 | * Called by kernel when device never acknowledges a transmit has | |
1001 | * completed (or failed) - i.e. never posted a Tx related interrupt. | |
1002 | */ | |
1003 | ||
70eb1bfd | 1004 | static void axnet_tx_timeout(struct net_device *dev) |
1da177e4 LT |
1005 | { |
1006 | long e8390_base = dev->base_addr; | |
1007 | struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
1008 | int txsr, isr, tickssofar = jiffies - dev->trans_start; | |
1009 | unsigned long flags; | |
1010 | ||
8e269165 | 1011 | dev->stats.tx_errors++; |
1da177e4 LT |
1012 | |
1013 | spin_lock_irqsave(&ei_local->page_lock, flags); | |
1014 | txsr = inb(e8390_base+EN0_TSR); | |
1015 | isr = inb(e8390_base+EN0_ISR); | |
1016 | spin_unlock_irqrestore(&ei_local->page_lock, flags); | |
1017 | ||
1018 | printk(KERN_DEBUG "%s: Tx timed out, %s TSR=%#2x, ISR=%#2x, t=%d.\n", | |
1019 | dev->name, (txsr & ENTSR_ABT) ? "excess collisions." : | |
1020 | (isr) ? "lost interrupt?" : "cable problem?", txsr, isr, tickssofar); | |
1021 | ||
8e269165 | 1022 | if (!isr && !dev->stats.tx_packets) |
1da177e4 LT |
1023 | { |
1024 | /* The 8390 probably hasn't gotten on the cable yet. */ | |
1025 | ei_local->interface_num ^= 1; /* Try a different xcvr. */ | |
1026 | } | |
1027 | ||
1028 | /* Ugly but a reset can be slow, yet must be protected */ | |
1029 | ||
bd5a9346 | 1030 | spin_lock_irqsave(&ei_local->page_lock, flags); |
1da177e4 LT |
1031 | |
1032 | /* Try to restart the card. Perhaps the user has fixed something. */ | |
1033 | ei_reset_8390(dev); | |
1034 | AX88190_init(dev, 1); | |
1035 | ||
bd5a9346 | 1036 | spin_unlock_irqrestore(&ei_local->page_lock, flags); |
1da177e4 LT |
1037 | netif_wake_queue(dev); |
1038 | } | |
1039 | ||
1040 | /** | |
70eb1bfd | 1041 | * axnet_start_xmit - begin packet transmission |
1da177e4 LT |
1042 | * @skb: packet to be sent |
1043 | * @dev: network device to which packet is sent | |
1044 | * | |
1045 | * Sends a packet to an 8390 network device. | |
1046 | */ | |
1047 | ||
dbf02fae SH |
1048 | static netdev_tx_t axnet_start_xmit(struct sk_buff *skb, |
1049 | struct net_device *dev) | |
1da177e4 LT |
1050 | { |
1051 | long e8390_base = dev->base_addr; | |
1052 | struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
1053 | int length, send_length, output_page; | |
1054 | unsigned long flags; | |
1055 | u8 packet[ETH_ZLEN]; | |
1056 | ||
1057 | netif_stop_queue(dev); | |
1058 | ||
1059 | length = skb->len; | |
1060 | ||
1061 | /* Mask interrupts from the ethercard. | |
1062 | SMP: We have to grab the lock here otherwise the IRQ handler | |
1063 | on another CPU can flip window and race the IRQ mask set. We end | |
1064 | up trashing the mcast filter not disabling irqs if we don't lock */ | |
1065 | ||
1066 | spin_lock_irqsave(&ei_local->page_lock, flags); | |
1067 | outb_p(0x00, e8390_base + EN0_IMR); | |
1da177e4 LT |
1068 | |
1069 | /* | |
1070 | * Slow phase with lock held. | |
1071 | */ | |
1072 | ||
1da177e4 LT |
1073 | ei_local->irqlock = 1; |
1074 | ||
c61f26fa RK |
1075 | send_length = max(length, ETH_ZLEN); |
1076 | ||
1da177e4 LT |
1077 | /* |
1078 | * We have two Tx slots available for use. Find the first free | |
1079 | * slot, and then perform some sanity checks. With two Tx bufs, | |
1080 | * you get very close to transmitting back-to-back packets. With | |
1081 | * only one Tx buf, the transmitter sits idle while you reload the | |
1082 | * card, leaving a substantial gap between each transmitted packet. | |
1083 | */ | |
1084 | ||
1085 | if (ei_local->tx1 == 0) | |
1086 | { | |
1087 | output_page = ei_local->tx_start_page; | |
1088 | ei_local->tx1 = send_length; | |
1089 | if (ei_debug && ei_local->tx2 > 0) | |
1090 | printk(KERN_DEBUG "%s: idle transmitter tx2=%d, lasttx=%d, txing=%d.\n", | |
1091 | dev->name, ei_local->tx2, ei_local->lasttx, ei_local->txing); | |
1092 | } | |
1093 | else if (ei_local->tx2 == 0) | |
1094 | { | |
1095 | output_page = ei_local->tx_start_page + TX_PAGES/2; | |
1096 | ei_local->tx2 = send_length; | |
1097 | if (ei_debug && ei_local->tx1 > 0) | |
1098 | printk(KERN_DEBUG "%s: idle transmitter, tx1=%d, lasttx=%d, txing=%d.\n", | |
1099 | dev->name, ei_local->tx1, ei_local->lasttx, ei_local->txing); | |
1100 | } | |
1101 | else | |
1102 | { /* We should never get here. */ | |
1103 | if (ei_debug) | |
1104 | printk(KERN_DEBUG "%s: No Tx buffers free! tx1=%d tx2=%d last=%d\n", | |
1105 | dev->name, ei_local->tx1, ei_local->tx2, ei_local->lasttx); | |
1106 | ei_local->irqlock = 0; | |
1107 | netif_stop_queue(dev); | |
1108 | outb_p(ENISR_ALL, e8390_base + EN0_IMR); | |
bd5a9346 | 1109 | spin_unlock_irqrestore(&ei_local->page_lock, flags); |
8e269165 | 1110 | dev->stats.tx_errors++; |
5b548140 | 1111 | return NETDEV_TX_BUSY; |
1da177e4 LT |
1112 | } |
1113 | ||
1114 | /* | |
1115 | * Okay, now upload the packet and trigger a send if the transmitter | |
1116 | * isn't already sending. If it is busy, the interrupt handler will | |
1117 | * trigger the send later, upon receiving a Tx done interrupt. | |
1118 | */ | |
1119 | ||
1120 | if (length == skb->len) | |
1121 | ei_block_output(dev, length, skb->data, output_page); | |
1122 | else { | |
1123 | memset(packet, 0, ETH_ZLEN); | |
d626f62b | 1124 | skb_copy_from_linear_data(skb, packet, skb->len); |
1da177e4 LT |
1125 | ei_block_output(dev, length, packet, output_page); |
1126 | } | |
1127 | ||
1128 | if (! ei_local->txing) | |
1129 | { | |
1130 | ei_local->txing = 1; | |
1131 | NS8390_trigger_send(dev, send_length, output_page); | |
1132 | dev->trans_start = jiffies; | |
1133 | if (output_page == ei_local->tx_start_page) | |
1134 | { | |
1135 | ei_local->tx1 = -1; | |
1136 | ei_local->lasttx = -1; | |
1137 | } | |
1138 | else | |
1139 | { | |
1140 | ei_local->tx2 = -1; | |
1141 | ei_local->lasttx = -2; | |
1142 | } | |
1143 | } | |
1144 | else ei_local->txqueue++; | |
1145 | ||
1146 | if (ei_local->tx1 && ei_local->tx2) | |
1147 | netif_stop_queue(dev); | |
1148 | else | |
1149 | netif_start_queue(dev); | |
1150 | ||
1151 | /* Turn 8390 interrupts back on. */ | |
1152 | ei_local->irqlock = 0; | |
1153 | outb_p(ENISR_ALL, e8390_base + EN0_IMR); | |
1154 | ||
bd5a9346 | 1155 | spin_unlock_irqrestore(&ei_local->page_lock, flags); |
1da177e4 LT |
1156 | |
1157 | dev_kfree_skb (skb); | |
8e269165 | 1158 | dev->stats.tx_bytes += send_length; |
1da177e4 | 1159 | |
6ed10654 | 1160 | return NETDEV_TX_OK; |
1da177e4 LT |
1161 | } |
1162 | ||
1163 | /** | |
1164 | * ax_interrupt - handle the interrupts from an 8390 | |
1165 | * @irq: interrupt number | |
1166 | * @dev_id: a pointer to the net_device | |
1da177e4 LT |
1167 | * |
1168 | * Handle the ether interface interrupts. We pull packets from | |
1169 | * the 8390 via the card specific functions and fire them at the networking | |
1170 | * stack. We also handle transmit completions and wake the transmit path if | |
1171 | * necessary. We also update the counters and do other housekeeping as | |
1172 | * needed. | |
1173 | */ | |
1174 | ||
7d12e780 | 1175 | static irqreturn_t ax_interrupt(int irq, void *dev_id) |
1da177e4 LT |
1176 | { |
1177 | struct net_device *dev = dev_id; | |
1178 | long e8390_base; | |
1179 | int interrupts, nr_serviced = 0, i; | |
1180 | struct ei_device *ei_local; | |
1181 | int handled = 0; | |
1182 | ||
1da177e4 | 1183 | e8390_base = dev->base_addr; |
c31f28e7 | 1184 | ei_local = netdev_priv(dev); |
1da177e4 LT |
1185 | |
1186 | /* | |
1187 | * Protect the irq test too. | |
1188 | */ | |
1189 | ||
1190 | spin_lock(&ei_local->page_lock); | |
1191 | ||
1192 | if (ei_local->irqlock) | |
1193 | { | |
1194 | #if 1 /* This might just be an interrupt for a PCI device sharing this line */ | |
1195 | /* The "irqlock" check is only for testing. */ | |
1196 | printk(ei_local->irqlock | |
1197 | ? "%s: Interrupted while interrupts are masked! isr=%#2x imr=%#2x.\n" | |
1198 | : "%s: Reentering the interrupt handler! isr=%#2x imr=%#2x.\n", | |
1199 | dev->name, inb_p(e8390_base + EN0_ISR), | |
1200 | inb_p(e8390_base + EN0_IMR)); | |
1201 | #endif | |
1202 | spin_unlock(&ei_local->page_lock); | |
1203 | return IRQ_NONE; | |
1204 | } | |
1205 | ||
1206 | if (ei_debug > 3) | |
1207 | printk(KERN_DEBUG "%s: interrupt(isr=%#2.2x).\n", dev->name, | |
1208 | inb_p(e8390_base + EN0_ISR)); | |
1209 | ||
1210 | outb_p(0x00, e8390_base + EN0_ISR); | |
1211 | ei_local->irqlock = 1; | |
1212 | ||
1213 | /* !!Assumption!! -- we stay in page 0. Don't break this. */ | |
8e95a202 JP |
1214 | while ((interrupts = inb_p(e8390_base + EN0_ISR)) != 0 && |
1215 | ++nr_serviced < MAX_SERVICE) | |
1da177e4 LT |
1216 | { |
1217 | if (!netif_running(dev) || (interrupts == 0xff)) { | |
1218 | if (ei_debug > 1) | |
1219 | printk(KERN_WARNING "%s: interrupt from stopped card\n", dev->name); | |
1220 | outb_p(interrupts, e8390_base + EN0_ISR); | |
1221 | interrupts = 0; | |
1222 | break; | |
1223 | } | |
1224 | handled = 1; | |
1225 | ||
1226 | /* AX88190 bug fix. */ | |
1227 | outb_p(interrupts, e8390_base + EN0_ISR); | |
1228 | for (i = 0; i < 10; i++) { | |
1229 | if (!(inb(e8390_base + EN0_ISR) & interrupts)) | |
1230 | break; | |
1231 | outb_p(0, e8390_base + EN0_ISR); | |
1232 | outb_p(interrupts, e8390_base + EN0_ISR); | |
1233 | } | |
1234 | if (interrupts & ENISR_OVER) | |
1235 | ei_rx_overrun(dev); | |
1236 | else if (interrupts & (ENISR_RX+ENISR_RX_ERR)) | |
1237 | { | |
1238 | /* Got a good (?) packet. */ | |
1239 | ei_receive(dev); | |
1240 | } | |
1241 | /* Push the next to-transmit packet through. */ | |
1242 | if (interrupts & ENISR_TX) | |
1243 | ei_tx_intr(dev); | |
1244 | else if (interrupts & ENISR_TX_ERR) | |
1245 | ei_tx_err(dev); | |
1246 | ||
1247 | if (interrupts & ENISR_COUNTERS) | |
1248 | { | |
8e269165 PZ |
1249 | dev->stats.rx_frame_errors += inb_p(e8390_base + EN0_COUNTER0); |
1250 | dev->stats.rx_crc_errors += inb_p(e8390_base + EN0_COUNTER1); | |
1251 | dev->stats.rx_missed_errors+= inb_p(e8390_base + EN0_COUNTER2); | |
1da177e4 LT |
1252 | } |
1253 | } | |
1254 | ||
36c86bd2 | 1255 | if (interrupts && ei_debug > 3) |
1da177e4 LT |
1256 | { |
1257 | handled = 1; | |
1258 | if (nr_serviced >= MAX_SERVICE) | |
1259 | { | |
1260 | /* 0xFF is valid for a card removal */ | |
1261 | if(interrupts!=0xFF) | |
1262 | printk(KERN_WARNING "%s: Too much work at interrupt, status %#2.2x\n", | |
1263 | dev->name, interrupts); | |
1264 | outb_p(ENISR_ALL, e8390_base + EN0_ISR); /* Ack. most intrs. */ | |
1265 | } else { | |
1266 | printk(KERN_WARNING "%s: unknown interrupt %#2x\n", dev->name, interrupts); | |
1267 | outb_p(0xff, e8390_base + EN0_ISR); /* Ack. all intrs. */ | |
1268 | } | |
1269 | } | |
1270 | ||
1271 | /* Turn 8390 interrupts back on. */ | |
1272 | ei_local->irqlock = 0; | |
1273 | outb_p(ENISR_ALL, e8390_base + EN0_IMR); | |
1274 | ||
1275 | spin_unlock(&ei_local->page_lock); | |
1276 | return IRQ_RETVAL(handled); | |
1277 | } | |
1278 | ||
1279 | /** | |
1280 | * ei_tx_err - handle transmitter error | |
1281 | * @dev: network device which threw the exception | |
1282 | * | |
1283 | * A transmitter error has happened. Most likely excess collisions (which | |
1284 | * is a fairly normal condition). If the error is one where the Tx will | |
1285 | * have been aborted, we try and send another one right away, instead of | |
1286 | * letting the failed packet sit and collect dust in the Tx buffer. This | |
1287 | * is a much better solution as it avoids kernel based Tx timeouts, and | |
1288 | * an unnecessary card reset. | |
1289 | * | |
1290 | * Called with lock held. | |
1291 | */ | |
1292 | ||
1293 | static void ei_tx_err(struct net_device *dev) | |
1294 | { | |
1295 | long e8390_base = dev->base_addr; | |
1da177e4 LT |
1296 | unsigned char txsr = inb_p(e8390_base+EN0_TSR); |
1297 | unsigned char tx_was_aborted = txsr & (ENTSR_ABT+ENTSR_FU); | |
1298 | ||
1299 | #ifdef VERBOSE_ERROR_DUMP | |
1300 | printk(KERN_DEBUG "%s: transmitter error (%#2x): ", dev->name, txsr); | |
1301 | if (txsr & ENTSR_ABT) | |
1302 | printk("excess-collisions "); | |
1303 | if (txsr & ENTSR_ND) | |
1304 | printk("non-deferral "); | |
1305 | if (txsr & ENTSR_CRS) | |
1306 | printk("lost-carrier "); | |
1307 | if (txsr & ENTSR_FU) | |
1308 | printk("FIFO-underrun "); | |
1309 | if (txsr & ENTSR_CDH) | |
1310 | printk("lost-heartbeat "); | |
1311 | printk("\n"); | |
1312 | #endif | |
1313 | ||
1314 | if (tx_was_aborted) | |
1315 | ei_tx_intr(dev); | |
1316 | else | |
1317 | { | |
8e269165 PZ |
1318 | dev->stats.tx_errors++; |
1319 | if (txsr & ENTSR_CRS) dev->stats.tx_carrier_errors++; | |
1320 | if (txsr & ENTSR_CDH) dev->stats.tx_heartbeat_errors++; | |
1321 | if (txsr & ENTSR_OWC) dev->stats.tx_window_errors++; | |
1da177e4 LT |
1322 | } |
1323 | } | |
1324 | ||
1325 | /** | |
1326 | * ei_tx_intr - transmit interrupt handler | |
1327 | * @dev: network device for which tx intr is handled | |
1328 | * | |
1329 | * We have finished a transmit: check for errors and then trigger the next | |
1330 | * packet to be sent. Called with lock held. | |
1331 | */ | |
1332 | ||
1333 | static void ei_tx_intr(struct net_device *dev) | |
1334 | { | |
1335 | long e8390_base = dev->base_addr; | |
1336 | struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
1337 | int status = inb(e8390_base + EN0_TSR); | |
1338 | ||
1339 | /* | |
1340 | * There are two Tx buffers, see which one finished, and trigger | |
1341 | * the send of another one if it exists. | |
1342 | */ | |
1343 | ei_local->txqueue--; | |
1344 | ||
1345 | if (ei_local->tx1 < 0) | |
1346 | { | |
1347 | if (ei_local->lasttx != 1 && ei_local->lasttx != -1) | |
1348 | printk(KERN_ERR "%s: bogus last_tx_buffer %d, tx1=%d.\n", | |
1349 | ei_local->name, ei_local->lasttx, ei_local->tx1); | |
1350 | ei_local->tx1 = 0; | |
1351 | if (ei_local->tx2 > 0) | |
1352 | { | |
1353 | ei_local->txing = 1; | |
1354 | NS8390_trigger_send(dev, ei_local->tx2, ei_local->tx_start_page + 6); | |
1355 | dev->trans_start = jiffies; | |
1356 | ei_local->tx2 = -1, | |
1357 | ei_local->lasttx = 2; | |
1358 | } | |
1359 | else ei_local->lasttx = 20, ei_local->txing = 0; | |
1360 | } | |
1361 | else if (ei_local->tx2 < 0) | |
1362 | { | |
1363 | if (ei_local->lasttx != 2 && ei_local->lasttx != -2) | |
1364 | printk("%s: bogus last_tx_buffer %d, tx2=%d.\n", | |
1365 | ei_local->name, ei_local->lasttx, ei_local->tx2); | |
1366 | ei_local->tx2 = 0; | |
1367 | if (ei_local->tx1 > 0) | |
1368 | { | |
1369 | ei_local->txing = 1; | |
1370 | NS8390_trigger_send(dev, ei_local->tx1, ei_local->tx_start_page); | |
1371 | dev->trans_start = jiffies; | |
1372 | ei_local->tx1 = -1; | |
1373 | ei_local->lasttx = 1; | |
1374 | } | |
1375 | else | |
1376 | ei_local->lasttx = 10, ei_local->txing = 0; | |
1377 | } | |
1378 | // else printk(KERN_WARNING "%s: unexpected TX-done interrupt, lasttx=%d.\n", | |
1379 | // dev->name, ei_local->lasttx); | |
1380 | ||
1381 | /* Minimize Tx latency: update the statistics after we restart TXing. */ | |
1382 | if (status & ENTSR_COL) | |
8e269165 | 1383 | dev->stats.collisions++; |
1da177e4 | 1384 | if (status & ENTSR_PTX) |
8e269165 | 1385 | dev->stats.tx_packets++; |
1da177e4 LT |
1386 | else |
1387 | { | |
8e269165 | 1388 | dev->stats.tx_errors++; |
1da177e4 LT |
1389 | if (status & ENTSR_ABT) |
1390 | { | |
8e269165 PZ |
1391 | dev->stats.tx_aborted_errors++; |
1392 | dev->stats.collisions += 16; | |
1da177e4 LT |
1393 | } |
1394 | if (status & ENTSR_CRS) | |
8e269165 | 1395 | dev->stats.tx_carrier_errors++; |
1da177e4 | 1396 | if (status & ENTSR_FU) |
8e269165 | 1397 | dev->stats.tx_fifo_errors++; |
1da177e4 | 1398 | if (status & ENTSR_CDH) |
8e269165 | 1399 | dev->stats.tx_heartbeat_errors++; |
1da177e4 | 1400 | if (status & ENTSR_OWC) |
8e269165 | 1401 | dev->stats.tx_window_errors++; |
1da177e4 LT |
1402 | } |
1403 | netif_wake_queue(dev); | |
1404 | } | |
1405 | ||
1406 | /** | |
1407 | * ei_receive - receive some packets | |
1408 | * @dev: network device with which receive will be run | |
1409 | * | |
1410 | * We have a good packet(s), get it/them out of the buffers. | |
1411 | * Called with lock held. | |
1412 | */ | |
1413 | ||
1414 | static void ei_receive(struct net_device *dev) | |
1415 | { | |
1416 | long e8390_base = dev->base_addr; | |
1417 | struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
1418 | unsigned char rxing_page, this_frame, next_frame; | |
1419 | unsigned short current_offset; | |
1420 | int rx_pkt_count = 0; | |
1421 | struct e8390_pkt_hdr rx_frame; | |
1422 | ||
1423 | while (++rx_pkt_count < 10) | |
1424 | { | |
1425 | int pkt_len, pkt_stat; | |
1426 | ||
1427 | /* Get the rx page (incoming packet pointer). */ | |
1428 | rxing_page = inb_p(e8390_base + EN1_CURPAG -1); | |
1429 | ||
1430 | /* Remove one frame from the ring. Boundary is always a page behind. */ | |
1431 | this_frame = inb_p(e8390_base + EN0_BOUNDARY) + 1; | |
1432 | if (this_frame >= ei_local->stop_page) | |
1433 | this_frame = ei_local->rx_start_page; | |
1434 | ||
1435 | /* Someday we'll omit the previous, iff we never get this message. | |
1436 | (There is at least one clone claimed to have a problem.) | |
1437 | ||
1438 | Keep quiet if it looks like a card removal. One problem here | |
1439 | is that some clones crash in roughly the same way. | |
1440 | */ | |
1441 | if (ei_debug > 0 && this_frame != ei_local->current_page && (this_frame!=0x0 || rxing_page!=0xFF)) | |
1442 | printk(KERN_ERR "%s: mismatched read page pointers %2x vs %2x.\n", | |
1443 | dev->name, this_frame, ei_local->current_page); | |
1444 | ||
1445 | if (this_frame == rxing_page) /* Read all the frames? */ | |
1446 | break; /* Done for now */ | |
1447 | ||
1448 | current_offset = this_frame << 8; | |
1449 | ei_get_8390_hdr(dev, &rx_frame, this_frame); | |
1450 | ||
1451 | pkt_len = rx_frame.count - sizeof(struct e8390_pkt_hdr); | |
1452 | pkt_stat = rx_frame.status; | |
1453 | ||
1454 | next_frame = this_frame + 1 + ((pkt_len+4)>>8); | |
1455 | ||
1456 | if (pkt_len < 60 || pkt_len > 1518) | |
1457 | { | |
1458 | if (ei_debug) | |
1459 | printk(KERN_DEBUG "%s: bogus packet size: %d, status=%#2x nxpg=%#2x.\n", | |
1460 | dev->name, rx_frame.count, rx_frame.status, | |
1461 | rx_frame.next); | |
8e269165 PZ |
1462 | dev->stats.rx_errors++; |
1463 | dev->stats.rx_length_errors++; | |
1da177e4 LT |
1464 | } |
1465 | else if ((pkt_stat & 0x0F) == ENRSR_RXOK) | |
1466 | { | |
1467 | struct sk_buff *skb; | |
1468 | ||
1469 | skb = dev_alloc_skb(pkt_len+2); | |
1470 | if (skb == NULL) | |
1471 | { | |
1472 | if (ei_debug > 1) | |
1473 | printk(KERN_DEBUG "%s: Couldn't allocate a sk_buff of size %d.\n", | |
1474 | dev->name, pkt_len); | |
8e269165 | 1475 | dev->stats.rx_dropped++; |
1da177e4 LT |
1476 | break; |
1477 | } | |
1478 | else | |
1479 | { | |
1480 | skb_reserve(skb,2); /* IP headers on 16 byte boundaries */ | |
1da177e4 LT |
1481 | skb_put(skb, pkt_len); /* Make room */ |
1482 | ei_block_input(dev, pkt_len, skb, current_offset + sizeof(rx_frame)); | |
1483 | skb->protocol=eth_type_trans(skb,dev); | |
1484 | netif_rx(skb); | |
8e269165 PZ |
1485 | dev->stats.rx_packets++; |
1486 | dev->stats.rx_bytes += pkt_len; | |
1da177e4 | 1487 | if (pkt_stat & ENRSR_PHY) |
8e269165 | 1488 | dev->stats.multicast++; |
1da177e4 LT |
1489 | } |
1490 | } | |
1491 | else | |
1492 | { | |
1493 | if (ei_debug) | |
1494 | printk(KERN_DEBUG "%s: bogus packet: status=%#2x nxpg=%#2x size=%d\n", | |
1495 | dev->name, rx_frame.status, rx_frame.next, | |
1496 | rx_frame.count); | |
8e269165 | 1497 | dev->stats.rx_errors++; |
1da177e4 LT |
1498 | /* NB: The NIC counts CRC, frame and missed errors. */ |
1499 | if (pkt_stat & ENRSR_FO) | |
8e269165 | 1500 | dev->stats.rx_fifo_errors++; |
1da177e4 LT |
1501 | } |
1502 | next_frame = rx_frame.next; | |
1503 | ||
1504 | /* This _should_ never happen: it's here for avoiding bad clones. */ | |
1505 | if (next_frame >= ei_local->stop_page) { | |
1506 | printk("%s: next frame inconsistency, %#2x\n", dev->name, | |
1507 | next_frame); | |
1508 | next_frame = ei_local->rx_start_page; | |
1509 | } | |
1510 | ei_local->current_page = next_frame; | |
1511 | outb_p(next_frame-1, e8390_base+EN0_BOUNDARY); | |
1512 | } | |
1513 | ||
1514 | return; | |
1515 | } | |
1516 | ||
1517 | /** | |
1518 | * ei_rx_overrun - handle receiver overrun | |
1519 | * @dev: network device which threw exception | |
1520 | * | |
1521 | * We have a receiver overrun: we have to kick the 8390 to get it started | |
1522 | * again. Problem is that you have to kick it exactly as NS prescribes in | |
1523 | * the updated datasheets, or "the NIC may act in an unpredictable manner." | |
1524 | * This includes causing "the NIC to defer indefinitely when it is stopped | |
1525 | * on a busy network." Ugh. | |
1526 | * Called with lock held. Don't call this with the interrupts off or your | |
1527 | * computer will hate you - it takes 10ms or so. | |
1528 | */ | |
1529 | ||
1530 | static void ei_rx_overrun(struct net_device *dev) | |
1531 | { | |
ff768cd7 | 1532 | axnet_dev_t *info = PRIV(dev); |
1da177e4 LT |
1533 | long e8390_base = dev->base_addr; |
1534 | unsigned char was_txing, must_resend = 0; | |
1da177e4 LT |
1535 | |
1536 | /* | |
1537 | * Record whether a Tx was in progress and then issue the | |
1538 | * stop command. | |
1539 | */ | |
1540 | was_txing = inb_p(e8390_base+E8390_CMD) & E8390_TRANS; | |
1541 | outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, e8390_base+E8390_CMD); | |
1542 | ||
1543 | if (ei_debug > 1) | |
1544 | printk(KERN_DEBUG "%s: Receiver overrun.\n", dev->name); | |
8e269165 | 1545 | dev->stats.rx_over_errors++; |
1da177e4 LT |
1546 | |
1547 | /* | |
1548 | * Wait a full Tx time (1.2ms) + some guard time, NS says 1.6ms total. | |
1549 | * Early datasheets said to poll the reset bit, but now they say that | |
1550 | * it "is not a reliable indicator and subsequently should be ignored." | |
1551 | * We wait at least 10ms. | |
1552 | */ | |
1553 | ||
1554 | mdelay(10); | |
1555 | ||
1556 | /* | |
1557 | * Reset RBCR[01] back to zero as per magic incantation. | |
1558 | */ | |
1559 | outb_p(0x00, e8390_base+EN0_RCNTLO); | |
1560 | outb_p(0x00, e8390_base+EN0_RCNTHI); | |
1561 | ||
1562 | /* | |
1563 | * See if any Tx was interrupted or not. According to NS, this | |
1564 | * step is vital, and skipping it will cause no end of havoc. | |
1565 | */ | |
1566 | ||
1567 | if (was_txing) | |
1568 | { | |
1569 | unsigned char tx_completed = inb_p(e8390_base+EN0_ISR) & (ENISR_TX+ENISR_TX_ERR); | |
1570 | if (!tx_completed) | |
1571 | must_resend = 1; | |
1572 | } | |
1573 | ||
1574 | /* | |
1575 | * Have to enter loopback mode and then restart the NIC before | |
1576 | * you are allowed to slurp packets up off the ring. | |
1577 | */ | |
1578 | outb_p(E8390_TXOFF, e8390_base + EN0_TXCR); | |
1579 | outb_p(E8390_NODMA + E8390_PAGE0 + E8390_START, e8390_base + E8390_CMD); | |
1580 | ||
1581 | /* | |
1582 | * Clear the Rx ring of all the debris, and ack the interrupt. | |
1583 | */ | |
1584 | ei_receive(dev); | |
1585 | ||
1586 | /* | |
1587 | * Leave loopback mode, and resend any packet that got stopped. | |
1588 | */ | |
1589 | outb_p(E8390_TXCONFIG | info->duplex_flag, e8390_base + EN0_TXCR); | |
1590 | if (must_resend) | |
1591 | outb_p(E8390_NODMA + E8390_PAGE0 + E8390_START + E8390_TRANS, e8390_base + E8390_CMD); | |
1592 | } | |
1593 | ||
1594 | /* | |
1595 | * Collect the stats. This is called unlocked and from several contexts. | |
1596 | */ | |
1597 | ||
1598 | static struct net_device_stats *get_stats(struct net_device *dev) | |
1599 | { | |
1600 | long ioaddr = dev->base_addr; | |
1601 | struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
1602 | unsigned long flags; | |
1603 | ||
1604 | /* If the card is stopped, just return the present stats. */ | |
1605 | if (!netif_running(dev)) | |
8e269165 | 1606 | return &dev->stats; |
1da177e4 LT |
1607 | |
1608 | spin_lock_irqsave(&ei_local->page_lock,flags); | |
1609 | /* Read the counter registers, assuming we are in page 0. */ | |
8e269165 PZ |
1610 | dev->stats.rx_frame_errors += inb_p(ioaddr + EN0_COUNTER0); |
1611 | dev->stats.rx_crc_errors += inb_p(ioaddr + EN0_COUNTER1); | |
1612 | dev->stats.rx_missed_errors+= inb_p(ioaddr + EN0_COUNTER2); | |
1da177e4 LT |
1613 | spin_unlock_irqrestore(&ei_local->page_lock, flags); |
1614 | ||
8e269165 | 1615 | return &dev->stats; |
1da177e4 LT |
1616 | } |
1617 | ||
b8ab2dc3 K |
1618 | /* |
1619 | * Form the 64 bit 8390 multicast table from the linked list of addresses | |
1620 | * associated with this dev structure. | |
1621 | */ | |
1622 | ||
1623 | static inline void make_mc_bits(u8 *bits, struct net_device *dev) | |
1624 | { | |
1625 | struct dev_mc_list *dmi; | |
1626 | u32 crc; | |
1627 | ||
91fea585 | 1628 | netdev_for_each_mc_addr(dmi, dev) { |
b8ab2dc3 K |
1629 | crc = ether_crc(ETH_ALEN, dmi->dmi_addr); |
1630 | /* | |
1631 | * The 8390 uses the 6 most significant bits of the | |
1632 | * CRC to index the multicast table. | |
1633 | */ | |
1634 | bits[crc>>29] |= (1<<((crc>>26)&7)); | |
1635 | } | |
1636 | } | |
1637 | ||
1da177e4 LT |
1638 | /** |
1639 | * do_set_multicast_list - set/clear multicast filter | |
1640 | * @dev: net device for which multicast filter is adjusted | |
1641 | * | |
b8ab2dc3 K |
1642 | * Set or clear the multicast filter for this adaptor. |
1643 | * Must be called with lock held. | |
1da177e4 LT |
1644 | */ |
1645 | ||
1646 | static void do_set_multicast_list(struct net_device *dev) | |
1647 | { | |
1648 | long e8390_base = dev->base_addr; | |
b8ab2dc3 K |
1649 | int i; |
1650 | struct ei_device *ei_local = (struct ei_device*)netdev_priv(dev); | |
1651 | ||
1652 | if (!(dev->flags&(IFF_PROMISC|IFF_ALLMULTI))) { | |
1653 | memset(ei_local->mcfilter, 0, 8); | |
91fea585 | 1654 | if (!netdev_mc_empty(dev)) |
b8ab2dc3 K |
1655 | make_mc_bits(ei_local->mcfilter, dev); |
1656 | } else { | |
1657 | /* set to accept-all */ | |
1658 | memset(ei_local->mcfilter, 0xFF, 8); | |
1659 | } | |
1660 | ||
b8ab2dc3 K |
1661 | outb_p(E8390_NODMA + E8390_PAGE1, e8390_base + E8390_CMD); |
1662 | for(i = 0; i < 8; i++) | |
1663 | { | |
1664 | outb_p(ei_local->mcfilter[i], e8390_base + EN1_MULT_SHIFT(i)); | |
1665 | } | |
1666 | outb_p(E8390_NODMA + E8390_PAGE0, e8390_base + E8390_CMD); | |
1da177e4 LT |
1667 | |
1668 | if(dev->flags&IFF_PROMISC) | |
1669 | outb_p(E8390_RXCONFIG | 0x58, e8390_base + EN0_RXCR); | |
91fea585 | 1670 | else if (dev->flags & IFF_ALLMULTI || !netdev_mc_empty(dev)) |
1da177e4 LT |
1671 | outb_p(E8390_RXCONFIG | 0x48, e8390_base + EN0_RXCR); |
1672 | else | |
1673 | outb_p(E8390_RXCONFIG | 0x40, e8390_base + EN0_RXCR); | |
f905703a K |
1674 | |
1675 | outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, e8390_base+E8390_CMD); | |
1da177e4 LT |
1676 | } |
1677 | ||
1678 | /* | |
1679 | * Called without lock held. This is invoked from user context and may | |
1680 | * be parallel to just about everything else. Its also fairly quick and | |
1681 | * not called too often. Must protect against both bh and irq users | |
1682 | */ | |
1683 | ||
1684 | static void set_multicast_list(struct net_device *dev) | |
1685 | { | |
1686 | unsigned long flags; | |
1687 | ||
1688 | spin_lock_irqsave(&dev_lock(dev), flags); | |
1689 | do_set_multicast_list(dev); | |
1690 | spin_unlock_irqrestore(&dev_lock(dev), flags); | |
1691 | } | |
1692 | ||
1da177e4 LT |
1693 | /* This page of functions should be 8390 generic */ |
1694 | /* Follow National Semi's recommendations for initializing the "NIC". */ | |
1695 | ||
1696 | /** | |
1697 | * AX88190_init - initialize 8390 hardware | |
1698 | * @dev: network device to initialize | |
1699 | * @startp: boolean. non-zero value to initiate chip processing | |
1700 | * | |
1701 | * Must be called with lock held. | |
1702 | */ | |
1703 | ||
1704 | static void AX88190_init(struct net_device *dev, int startp) | |
1705 | { | |
1706 | axnet_dev_t *info = PRIV(dev); | |
1707 | long e8390_base = dev->base_addr; | |
1708 | struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
1709 | int i; | |
1710 | int endcfg = ei_local->word16 ? (0x48 | ENDCFG_WTS) : 0x48; | |
1711 | ||
1712 | if(sizeof(struct e8390_pkt_hdr)!=4) | |
1713 | panic("8390.c: header struct mispacked\n"); | |
1714 | /* Follow National Semi's recommendations for initing the DP83902. */ | |
1715 | outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, e8390_base+E8390_CMD); /* 0x21 */ | |
1716 | outb_p(endcfg, e8390_base + EN0_DCFG); /* 0x48 or 0x49 */ | |
1717 | /* Clear the remote byte count registers. */ | |
1718 | outb_p(0x00, e8390_base + EN0_RCNTLO); | |
1719 | outb_p(0x00, e8390_base + EN0_RCNTHI); | |
1720 | /* Set to monitor and loopback mode -- this is vital!. */ | |
1721 | outb_p(E8390_RXOFF|0x40, e8390_base + EN0_RXCR); /* 0x60 */ | |
1722 | outb_p(E8390_TXOFF, e8390_base + EN0_TXCR); /* 0x02 */ | |
1723 | /* Set the transmit page and receive ring. */ | |
1724 | outb_p(ei_local->tx_start_page, e8390_base + EN0_TPSR); | |
1725 | ei_local->tx1 = ei_local->tx2 = 0; | |
1726 | outb_p(ei_local->rx_start_page, e8390_base + EN0_STARTPG); | |
1727 | outb_p(ei_local->stop_page-1, e8390_base + EN0_BOUNDARY); /* 3c503 says 0x3f,NS0x26*/ | |
1728 | ei_local->current_page = ei_local->rx_start_page; /* assert boundary+1 */ | |
1729 | outb_p(ei_local->stop_page, e8390_base + EN0_STOPPG); | |
1730 | /* Clear the pending interrupts and mask. */ | |
1731 | outb_p(0xFF, e8390_base + EN0_ISR); | |
1732 | outb_p(0x00, e8390_base + EN0_IMR); | |
1733 | ||
1734 | /* Copy the station address into the DS8390 registers. */ | |
1735 | ||
1736 | outb_p(E8390_NODMA + E8390_PAGE1 + E8390_STOP, e8390_base+E8390_CMD); /* 0x61 */ | |
1737 | for(i = 0; i < 6; i++) | |
1738 | { | |
1739 | outb_p(dev->dev_addr[i], e8390_base + EN1_PHYS_SHIFT(i)); | |
1740 | if(inb_p(e8390_base + EN1_PHYS_SHIFT(i))!=dev->dev_addr[i]) | |
1741 | printk(KERN_ERR "Hw. address read/write mismap %d\n",i); | |
1742 | } | |
1da177e4 LT |
1743 | |
1744 | outb_p(ei_local->rx_start_page, e8390_base + EN1_CURPAG); | |
1745 | outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, e8390_base+E8390_CMD); | |
1746 | ||
1747 | netif_start_queue(dev); | |
1748 | ei_local->tx1 = ei_local->tx2 = 0; | |
1749 | ei_local->txing = 0; | |
1750 | ||
ad3620a0 KK |
1751 | if (info->flags & IS_AX88790) /* select Internal PHY */ |
1752 | outb(0x10, e8390_base + AXNET_GPIO); | |
1753 | ||
1da177e4 LT |
1754 | if (startp) |
1755 | { | |
1756 | outb_p(0xff, e8390_base + EN0_ISR); | |
1757 | outb_p(ENISR_ALL, e8390_base + EN0_IMR); | |
1758 | outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, e8390_base+E8390_CMD); | |
1759 | outb_p(E8390_TXCONFIG | info->duplex_flag, | |
1760 | e8390_base + EN0_TXCR); /* xmit on. */ | |
1761 | /* 3c503 TechMan says rxconfig only after the NIC is started. */ | |
1762 | outb_p(E8390_RXCONFIG | 0x40, e8390_base + EN0_RXCR); /* rx on, */ | |
1763 | do_set_multicast_list(dev); /* (re)load the mcast table */ | |
1764 | } | |
1765 | } | |
1766 | ||
1767 | /* Trigger a transmit start, assuming the length is valid. | |
1768 | Always called with the page lock held */ | |
1769 | ||
1770 | static void NS8390_trigger_send(struct net_device *dev, unsigned int length, | |
1771 | int start_page) | |
1772 | { | |
1773 | long e8390_base = dev->base_addr; | |
1774 | struct ei_device *ei_local __attribute((unused)) = (struct ei_device *) netdev_priv(dev); | |
1775 | ||
1776 | if (inb_p(e8390_base) & E8390_TRANS) | |
1777 | { | |
1778 | printk(KERN_WARNING "%s: trigger_send() called with the transmitter busy.\n", | |
1779 | dev->name); | |
1780 | return; | |
1781 | } | |
1782 | outb_p(length & 0xff, e8390_base + EN0_TCNTLO); | |
1783 | outb_p(length >> 8, e8390_base + EN0_TCNTHI); | |
1784 | outb_p(start_page, e8390_base + EN0_TPSR); | |
1785 | outb_p(E8390_NODMA+E8390_TRANS+E8390_START, e8390_base+E8390_CMD); | |
1786 | } |