[deliverable/linux.git] / drivers / net / phy / bcm7xxx.c

/*
 * Broadcom BCM7xxx internal transceivers support.
 *
 * Copyright (C) 2014, Broadcom Corporation
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * as published by the Free Software Foundation; either version
 * 2 of the License, or (at your option) any later version.
 */

#include <linux/module.h>
#include <linux/phy.h>
#include <linux/delay.h>
#include <linux/bitops.h>
#include <linux/brcmphy.h>
#include <linux/mdio.h>

/* Broadcom BCM7xxx internal PHY registers */
#define MII_BCM7XXX_CHANNEL_WIDTH	0x2000

/* 40nm only register definitions */
#define MII_BCM7XXX_100TX_AUX_CTL	0x10
#define MII_BCM7XXX_100TX_FALSE_CAR	0x13
#define MII_BCM7XXX_100TX_DISC		0x14
#define MII_BCM7XXX_AUX_MODE		0x1d
#define  MII_BCM7XX_64CLK_MDIO		BIT(12)
#define MII_BCM7XXX_CORE_BASE1E		0x1e
#define MII_BCM7XXX_TEST		0x1f
#define  MII_BCM7XXX_SHD_MODE_2		BIT(2)

/* 28nm only register definitions */
#define MISC_ADDR(base, channel)	base, channel

#define DSP_TAP10			MISC_ADDR(0x0a, 0)
#define PLL_PLLCTRL_1			MISC_ADDR(0x32, 1)
#define PLL_PLLCTRL_2			MISC_ADDR(0x32, 2)
#define PLL_PLLCTRL_4			MISC_ADDR(0x33, 0)

#define AFE_RXCONFIG_0			MISC_ADDR(0x38, 0)
#define AFE_RXCONFIG_1			MISC_ADDR(0x38, 1)
#define AFE_RXCONFIG_2			MISC_ADDR(0x38, 2)
#define AFE_RX_LP_COUNTER		MISC_ADDR(0x38, 3)
#define AFE_TX_CONFIG			MISC_ADDR(0x39, 0)
#define AFE_VDCA_ICTRL_0		MISC_ADDR(0x39, 1)
#define AFE_VDAC_OTHERS_0		MISC_ADDR(0x39, 3)
#define AFE_HPF_TRIM_OTHERS		MISC_ADDR(0x3a, 0)

#define CORE_EXPB0			0xb0

static void phy_write_exp(struct phy_device *phydev,
					u16 reg, u16 value)
{
	phy_write(phydev, MII_BCM54XX_EXP_SEL, MII_BCM54XX_EXP_SEL_ER | reg);
	phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
}

static void phy_write_misc(struct phy_device *phydev,
					u16 reg, u16 chl, u16 value)
{
	int tmp;

	phy_write(phydev, MII_BCM54XX_AUX_CTL, MII_BCM54XX_AUXCTL_SHDWSEL_MISC);

	tmp = phy_read(phydev, MII_BCM54XX_AUX_CTL);
	tmp |= MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA;
	phy_write(phydev, MII_BCM54XX_AUX_CTL, tmp);

	tmp = (chl * MII_BCM7XXX_CHANNEL_WIDTH) | reg;
	phy_write(phydev, MII_BCM54XX_EXP_SEL, tmp);

	phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
}

static void r_rc_cal_reset(struct phy_device *phydev)
{
	/* Reset R_CAL/RC_CAL Engine */
	phy_write_exp(phydev, 0x00b0, 0x0010);

	/* Disable Reset R_AL/RC_CAL Engine */
	phy_write_exp(phydev, 0x00b0, 0x0000);
}

static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev)
{
	/* Increase VCO range to prevent unlocking problem of PLL at low
	 * temp
	 */
	phy_write_misc(phydev, PLL_PLLCTRL_1, 0x0048);

	/* Change Ki to 011 */
	phy_write_misc(phydev, PLL_PLLCTRL_2, 0x021b);

	/* Disable loading of TVCO buffer to bandgap, set bandgap trim
	 * to 111
	 */
	phy_write_misc(phydev, PLL_PLLCTRL_4, 0x0e20);

	/* Adjust bias current trim by -3 */
	phy_write_misc(phydev, DSP_TAP10, 0x690b);

	/* Switch to CORE_BASE1E */
	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0xd);

	r_rc_cal_reset(phydev);

	/* write AFE_RXCONFIG_0 */
	phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19);

	/* write AFE_RXCONFIG_1 */
	phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9a3f);

	/* write AFE_RX_LP_COUNTER */
	phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);

	/* write AFE_HPF_TRIM_OTHERS */
	phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x000b);

	/* write AFTE_TX_CONFIG */
	phy_write_misc(phydev, AFE_TX_CONFIG, 0x0800);

	return 0;
}

static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev)
{
	/* AFE_RXCONFIG_0 */
	phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15);

	/* AFE_RXCONFIG_1 */
	phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);

	/* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2 code */
	phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003);

	/* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */
	phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);

	/* AFE_TX_CONFIG, set 1000BT Cfeed=110 for all ports */
	phy_write_misc(phydev, AFE_TX_CONFIG, 0x0061);

	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
	phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);

	/* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */
	phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020);

	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
	 * offset for HT=0 code
	 */
	phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);

	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010);

	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
	phy_write_misc(phydev, DSP_TAP10, 0x011b);

	/* Reset R_CAL/RC_CAL engine */
	r_rc_cal_reset(phydev);

	return 0;
}

static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev)
{
	/* AFE_RXCONFIG_1, provide more margin for INL/DNL measurement */
	phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);

	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
	phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);

	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
	 * offset for HT=0 code
	 */
	phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);

	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010);

	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
	phy_write_misc(phydev, DSP_TAP10, 0x011b);

	/* Reset R_CAL/RC_CAL engine */
	r_rc_cal_reset(phydev);

	return 0;
}

static int bcm7xxx_apd_enable(struct phy_device *phydev)
{
	int val;

	/* Enable powering down of the DLL during auto-power down */
	val = bcm54xx_shadow_read(phydev, BCM54XX_SHD_SCR3);
	if (val < 0)
		return val;

	val |= BCM54XX_SHD_SCR3_DLLAPD_DIS;
	bcm54xx_shadow_write(phydev, BCM54XX_SHD_SCR3, val);

	/* Enable auto-power down */
	val = bcm54xx_shadow_read(phydev, BCM54XX_SHD_APD);
	if (val < 0)
		return val;

	val |= BCM54XX_SHD_APD_EN;
	return bcm54xx_shadow_write(phydev, BCM54XX_SHD_APD, val);
}

static int bcm7xxx_eee_enable(struct phy_device *phydev)
{
	int val;

	val = phy_read_mmd_indirect(phydev, BRCM_CL45VEN_EEE_CONTROL,
				    MDIO_MMD_AN, phydev->addr);
	if (val < 0)
		return val;

	/* Enable general EEE feature at the PHY level */
	val |= LPI_FEATURE_EN | LPI_FEATURE_EN_DIG1000X;

	phy_write_mmd_indirect(phydev, BRCM_CL45VEN_EEE_CONTROL,
			       MDIO_MMD_AN, phydev->addr, val);

	/* Advertise supported modes */
	val = phy_read_mmd_indirect(phydev, MDIO_AN_EEE_ADV,
				    MDIO_MMD_AN, phydev->addr);

	val |= (MDIO_AN_EEE_ADV_100TX | MDIO_AN_EEE_ADV_1000T);
	phy_write_mmd_indirect(phydev, MDIO_AN_EEE_ADV,
			       MDIO_MMD_AN, phydev->addr, val);

	return 0;
}

static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
{
	u8 rev = PHY_BRCM_7XXX_REV(phydev->dev_flags);
	u8 patch = PHY_BRCM_7XXX_PATCH(phydev->dev_flags);
	int ret = 0;

	pr_info_once("%s: %s PHY revision: 0x%02x, patch: %d\n",
		     dev_name(&phydev->dev), phydev->drv->name, rev, patch);

	switch (rev) {
	case 0xb0:
		ret = bcm7xxx_28nm_b0_afe_config_init(phydev);
		break;
	case 0xd0:
		ret = bcm7xxx_28nm_d0_afe_config_init(phydev);
		break;
	case 0xe0:
	case 0xf0:
		ret = bcm7xxx_28nm_e0_plus_afe_config_init(phydev);
		break;
	default:
		break;
	}

	if (ret)
		return ret;

	ret = bcm7xxx_eee_enable(phydev);
	if (ret)
		return ret;

	return bcm7xxx_apd_enable(phydev);
}

static int bcm7xxx_28nm_resume(struct phy_device *phydev)
{
	int ret;

	/* Re-apply workarounds coming out suspend/resume */
	ret = bcm7xxx_28nm_config_init(phydev);
	if (ret)
		return ret;

	/* 28nm Gigabit PHYs come out of reset without any half-duplex
	 * or "hub" compliant advertised mode, fix that. This does not
	 * cause any problems with the PHY library since genphy_config_aneg()
	 * gracefully handles auto-negotiated and forced modes.
	 */
	return genphy_config_aneg(phydev);
}

static int phy_set_clr_bits(struct phy_device *dev, int location,
					int set_mask, int clr_mask)
{
	int v, ret;

	v = phy_read(dev, location);
	if (v < 0)
		return v;

	v &= ~clr_mask;
	v |= set_mask;

	ret = phy_write(dev, location, v);
	if (ret < 0)
		return ret;

	return v;
}

static int bcm7xxx_config_init(struct phy_device *phydev)
{
	int ret;

	/* Enable 64 clock MDIO */
	phy_write(phydev, MII_BCM7XXX_AUX_MODE, MII_BCM7XX_64CLK_MDIO);
	phy_read(phydev, MII_BCM7XXX_AUX_MODE);

	/* Workaround only required for 100Mbits/sec capable PHYs */
	if (phydev->supported & PHY_GBIT_FEATURES)
		return 0;

	/* set shadow mode 2 */
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
			MII_BCM7XXX_SHD_MODE_2, MII_BCM7XXX_SHD_MODE_2);
	if (ret < 0)
		return ret;

	/* set iddq_clkbias */
	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0F00);
	udelay(10);

	/* reset iddq_clkbias */
	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0C00);

	phy_write(phydev, MII_BCM7XXX_100TX_FALSE_CAR, 0x7555);

	/* reset shadow mode 2 */
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, MII_BCM7XXX_SHD_MODE_2, 0);
	if (ret < 0)
		return ret;

	return 0;
}

/* Workaround for putting the PHY in IDDQ mode, required
 * for all BCM7XXX 40nm and 65nm PHYs
 */
static int bcm7xxx_suspend(struct phy_device *phydev)
{
	int ret;
	const struct bcm7xxx_regs {
		int reg;
		u16 value;
	} bcm7xxx_suspend_cfg[] = {
		{ MII_BCM7XXX_TEST, 0x008b },
		{ MII_BCM7XXX_100TX_AUX_CTL, 0x01c0 },
		{ MII_BCM7XXX_100TX_DISC, 0x7000 },
		{ MII_BCM7XXX_TEST, 0x000f },
		{ MII_BCM7XXX_100TX_AUX_CTL, 0x20d0 },
		{ MII_BCM7XXX_TEST, 0x000b },
	};
	unsigned int i;

	for (i = 0; i < ARRAY_SIZE(bcm7xxx_suspend_cfg); i++) {
		ret = phy_write(phydev,
				bcm7xxx_suspend_cfg[i].reg,
				bcm7xxx_suspend_cfg[i].value);
		if (ret)
			return ret;
	}

	return 0;
}

static int bcm7xxx_dummy_config_init(struct phy_device *phydev)
{
	return 0;
}

#define BCM7XXX_28NM_GPHY(_oui, _name)					\
{									\
	.phy_id		= (_oui),					\
	.phy_id_mask	= 0xfffffff0,					\
	.name		= _name,					\
	.features	= PHY_GBIT_FEATURES |				\
			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,	\
	.flags		= PHY_IS_INTERNAL,				\
	.config_init	= bcm7xxx_28nm_config_init,			\
	.config_aneg	= genphy_config_aneg,				\
	.read_status	= genphy_read_status,				\
	.resume		= bcm7xxx_28nm_resume,				\
	.driver		= { .owner = THIS_MODULE },			\
}

static struct phy_driver bcm7xxx_driver[] = {
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7250, "Broadcom BCM7250"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7364, "Broadcom BCM7364"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7366, "Broadcom BCM7366"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7439, "Broadcom BCM7439"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7445, "Broadcom BCM7445"),
{
	.phy_id         = PHY_ID_BCM7425,
	.phy_id_mask    = 0xfffffff0,
	.name           = "Broadcom BCM7425",
	.features       = PHY_GBIT_FEATURES |
			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
	.flags          = 0,
	.config_init    = bcm7xxx_config_init,
	.config_aneg    = genphy_config_aneg,
	.read_status    = genphy_read_status,
	.suspend        = bcm7xxx_suspend,
	.resume         = bcm7xxx_config_init,
	.driver         = { .owner = THIS_MODULE },
}, {
	.phy_id         = PHY_ID_BCM7429,
	.phy_id_mask    = 0xfffffff0,
	.name           = "Broadcom BCM7429",
	.features       = PHY_GBIT_FEATURES |
			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
	.flags          = PHY_IS_INTERNAL,
	.config_init    = bcm7xxx_config_init,
	.config_aneg    = genphy_config_aneg,
	.read_status    = genphy_read_status,
	.suspend        = bcm7xxx_suspend,
	.resume         = bcm7xxx_config_init,
	.driver         = { .owner = THIS_MODULE },
}, {
	.phy_id		= PHY_BCM_OUI_4,
	.phy_id_mask	= 0xffff0000,
	.name		= "Broadcom BCM7XXX 40nm",
	.features	= PHY_GBIT_FEATURES |
			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
	.flags		= PHY_IS_INTERNAL,
	.config_init	= bcm7xxx_config_init,
	.config_aneg	= genphy_config_aneg,
	.read_status	= genphy_read_status,
	.suspend	= bcm7xxx_suspend,
	.resume		= bcm7xxx_config_init,
	.driver		= { .owner = THIS_MODULE },
}, {
	.phy_id		= PHY_BCM_OUI_5,
	.phy_id_mask	= 0xffffff00,
	.name		= "Broadcom BCM7XXX 65nm",
	.features	= PHY_BASIC_FEATURES |
			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
	.flags		= PHY_IS_INTERNAL,
	.config_init	= bcm7xxx_dummy_config_init,
	.config_aneg	= genphy_config_aneg,
	.read_status	= genphy_read_status,
	.suspend	= bcm7xxx_suspend,
	.resume		= bcm7xxx_config_init,
	.driver		= { .owner = THIS_MODULE },
} };

static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = {
	{ PHY_ID_BCM7250, 0xfffffff0, },
	{ PHY_ID_BCM7364, 0xfffffff0, },
	{ PHY_ID_BCM7366, 0xfffffff0, },
	{ PHY_ID_BCM7425, 0xfffffff0, },
	{ PHY_ID_BCM7429, 0xfffffff0, },
	{ PHY_ID_BCM7439, 0xfffffff0, },
	{ PHY_ID_BCM7445, 0xfffffff0, },
	{ PHY_BCM_OUI_4, 0xffff0000 },
	{ PHY_BCM_OUI_5, 0xffffff00 },
	{ }
};

module_phy_driver(bcm7xxx_driver);

MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl);

MODULE_DESCRIPTION("Broadcom BCM7xxx internal PHY driver");
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Broadcom Corporation");
Commit	Line	Data
b560a58c FF	1	/*
	2	* Broadcom BCM7xxx internal transceivers support.
	3	*
	4	* Copyright (C) 2014, Broadcom Corporation
	5	*
	6	* This program is free software; you can redistribute it and/or
	7	* modify it under the terms of the GNU General Public License
	8	* as published by the Free Software Foundation; either version
	9	* 2 of the License, or (at your option) any later version.
	10	*/
	11
	12	#include <linux/module.h>
	13	#include <linux/phy.h>
	14	#include <linux/delay.h>
	15	#include <linux/bitops.h>
	16	#include <linux/brcmphy.h>
b8f9a029	17	#include <linux/mdio.h>
b560a58c FF	18
	19	/* Broadcom BCM7xxx internal PHY registers */
	20	#define MII_BCM7XXX_CHANNEL_WIDTH 0x2000
	21
	22	/* 40nm only register definitions */
	23	#define MII_BCM7XXX_100TX_AUX_CTL 0x10
	24	#define MII_BCM7XXX_100TX_FALSE_CAR 0x13
	25	#define MII_BCM7XXX_100TX_DISC 0x14
	26	#define MII_BCM7XXX_AUX_MODE 0x1d
	27	#define MII_BCM7XX_64CLK_MDIO BIT(12)
	28	#define MII_BCM7XXX_CORE_BASE1E 0x1e
	29	#define MII_BCM7XXX_TEST 0x1f
	30	#define MII_BCM7XXX_SHD_MODE_2 BIT(2)
	31
a3622f2c FF	32	/* 28nm only register definitions */
	33	#define MISC_ADDR(base, channel) base, channel
	34
	35	#define DSP_TAP10 MISC_ADDR(0x0a, 0)
	36	#define PLL_PLLCTRL_1 MISC_ADDR(0x32, 1)
	37	#define PLL_PLLCTRL_2 MISC_ADDR(0x32, 2)
	38	#define PLL_PLLCTRL_4 MISC_ADDR(0x33, 0)
	39
	40	#define AFE_RXCONFIG_0 MISC_ADDR(0x38, 0)
	41	#define AFE_RXCONFIG_1 MISC_ADDR(0x38, 1)
a490631f	42	#define AFE_RXCONFIG_2 MISC_ADDR(0x38, 2)
a3622f2c FF	43	#define AFE_RX_LP_COUNTER MISC_ADDR(0x38, 3)
a3622f2c FF	44	#define AFE_TX_CONFIG MISC_ADDR(0x39, 0)
a490631f FF	45	#define AFE_VDCA_ICTRL_0 MISC_ADDR(0x39, 1)
a490631f FF	46	#define AFE_VDAC_OTHERS_0 MISC_ADDR(0x39, 3)
a3622f2c FF	47	#define AFE_HPF_TRIM_OTHERS MISC_ADDR(0x3a, 0)
	48
	49	#define CORE_EXPB0 0xb0
	50
b560a58c FF	51	static void phy_write_exp(struct phy_device *phydev,
	52	u16 reg, u16 value)
	53	{
	54	phy_write(phydev, MII_BCM54XX_EXP_SEL, MII_BCM54XX_EXP_SEL_ER \| reg);
	55	phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
	56	}
	57
	58	static void phy_write_misc(struct phy_device *phydev,
	59	u16 reg, u16 chl, u16 value)
	60	{
	61	int tmp;
	62
	63	phy_write(phydev, MII_BCM54XX_AUX_CTL, MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
	64
	65	tmp = phy_read(phydev, MII_BCM54XX_AUX_CTL);
	66	tmp \|= MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA;
	67	phy_write(phydev, MII_BCM54XX_AUX_CTL, tmp);
	68
	69	tmp = (chl * MII_BCM7XXX_CHANNEL_WIDTH) \| reg;
	70	phy_write(phydev, MII_BCM54XX_EXP_SEL, tmp);
	71
	72	phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
	73	}
	74
9c41f2ba FF	75	static void r_rc_cal_reset(struct phy_device *phydev)
	76	{
	77	/* Reset R_CAL/RC_CAL Engine */
	78	phy_write_exp(phydev, 0x00b0, 0x0010);
	79
	80	/* Disable Reset R_AL/RC_CAL Engine */
	81	phy_write_exp(phydev, 0x00b0, 0x0000);
	82	}
	83
2a9df742	84	static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev)
b560a58c	85	{
b560a58c FF	86	/* Increase VCO range to prevent unlocking problem of PLL at low
	87	* temp
	88	*/
a3622f2c	89	phy_write_misc(phydev, PLL_PLLCTRL_1, 0x0048);
b560a58c FF	90
b560a58c FF	91	/* Change Ki to 011 */
a3622f2c	92	phy_write_misc(phydev, PLL_PLLCTRL_2, 0x021b);
b560a58c FF	93
	94	/* Disable loading of TVCO buffer to bandgap, set bandgap trim
	95	* to 111
	96	*/
a3622f2c	97	phy_write_misc(phydev, PLL_PLLCTRL_4, 0x0e20);
b560a58c FF	98
b560a58c FF	99	/* Adjust bias current trim by -3 */
a3622f2c	100	phy_write_misc(phydev, DSP_TAP10, 0x690b);
b560a58c FF	101
	102	/* Switch to CORE_BASE1E */
	103	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0xd);
	104
9c41f2ba	105	r_rc_cal_reset(phydev);
b560a58c	106
9918542e FF	107	/* write AFE_RXCONFIG_0 */
	108	phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19);
	109
	110	/* write AFE_RXCONFIG_1 */
	111	phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9a3f);
	112
	113	/* write AFE_RX_LP_COUNTER */
a62ea5a7	114	phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);
9918542e FF	115
	116	/* write AFE_HPF_TRIM_OTHERS */
	117	phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x000b);
	118
	119	/* write AFTE_TX_CONFIG */
	120	phy_write_misc(phydev, AFE_TX_CONFIG, 0x0800);
	121
b560a58c FF	122	return 0;
	123	}
	124
a490631f FF	125	static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev)
	126	{
	127	/* AFE_RXCONFIG_0 */
	128	phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15);
	129
	130	/* AFE_RXCONFIG_1 */
	131	phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);
	132
	133	/* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2 code */
	134	phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003);
	135
	136	/* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */
	137	phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);
	138
	139	/* AFE_TX_CONFIG, set 1000BT Cfeed=110 for all ports */
	140	phy_write_misc(phydev, AFE_TX_CONFIG, 0x0061);
	141
	142	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
	143	phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);
	144
	145	/* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */
	146	phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020);
	147
	148	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
	149	* offset for HT=0 code
	150	*/
	151	phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);
	152
	153	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
	154	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010);
	155
	156	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
	157	phy_write_misc(phydev, DSP_TAP10, 0x011b);
	158
	159	/* Reset R_CAL/RC_CAL engine */
	160	r_rc_cal_reset(phydev);
	161
	162	return 0;
	163	}
	164
0c2fdc25 FF	165	static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev)
	166	{
	167	/* AFE_RXCONFIG_1, provide more margin for INL/DNL measurement */
	168	phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);
	169
	170	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
	171	phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);
	172
	173	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
	174	* offset for HT=0 code
	175	*/
	176	phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);
	177
	178	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
	179	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010);
	180
	181	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
	182	phy_write_misc(phydev, DSP_TAP10, 0x011b);
	183
	184	/* Reset R_CAL/RC_CAL engine */
	185	r_rc_cal_reset(phydev);
	186
	187	return 0;
	188	}
	189
9df54dda FF	190	static int bcm7xxx_apd_enable(struct phy_device *phydev)
	191	{
	192	int val;
	193
	194	/* Enable powering down of the DLL during auto-power down */
	195	val = bcm54xx_shadow_read(phydev, BCM54XX_SHD_SCR3);
	196	if (val < 0)
	197	return val;
	198
	199	val \|= BCM54XX_SHD_SCR3_DLLAPD_DIS;
	200	bcm54xx_shadow_write(phydev, BCM54XX_SHD_SCR3, val);
	201
	202	/* Enable auto-power down */
	203	val = bcm54xx_shadow_read(phydev, BCM54XX_SHD_APD);
	204	if (val < 0)
	205	return val;
	206
	207	val \|= BCM54XX_SHD_APD_EN;
	208	return bcm54xx_shadow_write(phydev, BCM54XX_SHD_APD, val);
	209	}
	210
b8f9a029 FF	211	static int bcm7xxx_eee_enable(struct phy_device *phydev)
	212	{
	213	int val;
	214
	215	val = phy_read_mmd_indirect(phydev, BRCM_CL45VEN_EEE_CONTROL,
	216	MDIO_MMD_AN, phydev->addr);
	217	if (val < 0)
	218	return val;
	219
	220	/* Enable general EEE feature at the PHY level */
	221	val \|= LPI_FEATURE_EN \| LPI_FEATURE_EN_DIG1000X;
	222
	223	phy_write_mmd_indirect(phydev, BRCM_CL45VEN_EEE_CONTROL,
	224	MDIO_MMD_AN, phydev->addr, val);
	225
	226	/* Advertise supported modes */
	227	val = phy_read_mmd_indirect(phydev, MDIO_AN_EEE_ADV,
	228	MDIO_MMD_AN, phydev->addr);
	229
	230	val \|= (MDIO_AN_EEE_ADV_100TX \| MDIO_AN_EEE_ADV_1000T);
	231	phy_write_mmd_indirect(phydev, MDIO_AN_EEE_ADV,
	232	MDIO_MMD_AN, phydev->addr, val);
	233
	234	return 0;
	235	}
	236
b560a58c FF	237	static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
b560a58c FF	238	{
d8ebfed3 FF	239	u8 rev = PHY_BRCM_7XXX_REV(phydev->dev_flags);
	240	u8 patch = PHY_BRCM_7XXX_PATCH(phydev->dev_flags);
	241	int ret = 0;
	242
6ec259c1 FF	243	pr_info_once("%s: %s PHY revision: 0x%02x, patch: %d\n",
6ec259c1 FF	244	dev_name(&phydev->dev), phydev->drv->name, rev, patch);
d8ebfed3 FF	245
d8ebfed3 FF	246	switch (rev) {
d8ebfed3	247	case 0xb0:
2a9df742	248	ret = bcm7xxx_28nm_b0_afe_config_init(phydev);
d8ebfed3	249	break;
a490631f FF	250	case 0xd0:
	251	ret = bcm7xxx_28nm_d0_afe_config_init(phydev);
	252	break;
0c2fdc25 FF	253	case 0xe0:
	254	case 0xf0:
	255	ret = bcm7xxx_28nm_e0_plus_afe_config_init(phydev);
	256	break;
d8ebfed3	257	default:
d8ebfed3 FF	258	break;
d8ebfed3 FF	259	}
b560a58c	260
9df54dda FF	261	if (ret)
	262	return ret;
	263
b8f9a029 FF	264	ret = bcm7xxx_eee_enable(phydev);
	265	if (ret)
	266	return ret;
	267
9df54dda	268	return bcm7xxx_apd_enable(phydev);
b560a58c FF	269	}
b560a58c FF	270
4fd14e0b FF	271	static int bcm7xxx_28nm_resume(struct phy_device *phydev)
	272	{
	273	int ret;
	274
	275	/* Re-apply workarounds coming out suspend/resume */
	276	ret = bcm7xxx_28nm_config_init(phydev);
	277	if (ret)
	278	return ret;
	279
	280	/* 28nm Gigabit PHYs come out of reset without any half-duplex
	281	* or "hub" compliant advertised mode, fix that. This does not
	282	* cause any problems with the PHY library since genphy_config_aneg()
	283	* gracefully handles auto-negotiated and forced modes.
	284	*/
	285	return genphy_config_aneg(phydev);
	286	}
	287
b560a58c FF	288	static int phy_set_clr_bits(struct phy_device *dev, int location,
	289	int set_mask, int clr_mask)
	290	{
	291	int v, ret;
	292
	293	v = phy_read(dev, location);
	294	if (v < 0)
	295	return v;
	296
	297	v &= ~clr_mask;
	298	v \|= set_mask;
	299
	300	ret = phy_write(dev, location, v);
	301	if (ret < 0)
	302	return ret;
	303
	304	return v;
	305	}
	306
	307	static int bcm7xxx_config_init(struct phy_device *phydev)
	308	{
	309	int ret;
	310
	311	/* Enable 64 clock MDIO */
	312	phy_write(phydev, MII_BCM7XXX_AUX_MODE, MII_BCM7XX_64CLK_MDIO);
	313	phy_read(phydev, MII_BCM7XXX_AUX_MODE);
	314
e18556ee FF	315	/* Workaround only required for 100Mbits/sec capable PHYs */
e18556ee FF	316	if (phydev->supported & PHY_GBIT_FEATURES)
b560a58c FF	317	return 0;
	318
	319	/* set shadow mode 2 */
	320	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
	321	MII_BCM7XXX_SHD_MODE_2, MII_BCM7XXX_SHD_MODE_2);
	322	if (ret < 0)
	323	return ret;
	324
	325	/* set iddq_clkbias */
	326	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0F00);
	327	udelay(10);
	328
	329	/* reset iddq_clkbias */
	330	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0C00);
	331
	332	phy_write(phydev, MII_BCM7XXX_100TX_FALSE_CAR, 0x7555);
	333
	334	/* reset shadow mode 2 */
	335	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, MII_BCM7XXX_SHD_MODE_2, 0);
	336	if (ret < 0)
	337	return ret;
	338
	339	return 0;
	340	}
	341
	342	/* Workaround for putting the PHY in IDDQ mode, required
82c084f5	343	* for all BCM7XXX 40nm and 65nm PHYs
b560a58c FF	344	*/
	345	static int bcm7xxx_suspend(struct phy_device *phydev)
	346	{
	347	int ret;
	348	const struct bcm7xxx_regs {
	349	int reg;
	350	u16 value;
	351	} bcm7xxx_suspend_cfg[] = {
	352	{ MII_BCM7XXX_TEST, 0x008b },
	353	{ MII_BCM7XXX_100TX_AUX_CTL, 0x01c0 },
	354	{ MII_BCM7XXX_100TX_DISC, 0x7000 },
	355	{ MII_BCM7XXX_TEST, 0x000f },
	356	{ MII_BCM7XXX_100TX_AUX_CTL, 0x20d0 },
	357	{ MII_BCM7XXX_TEST, 0x000b },
	358	};
	359	unsigned int i;
	360
	361	for (i = 0; i < ARRAY_SIZE(bcm7xxx_suspend_cfg); i++) {
	362	ret = phy_write(phydev,
	363	bcm7xxx_suspend_cfg[i].reg,
	364	bcm7xxx_suspend_cfg[i].value);
	365	if (ret)
	366	return ret;
	367	}
	368
	369	return 0;
	370	}
	371
	372	static int bcm7xxx_dummy_config_init(struct phy_device *phydev)
	373	{
	374	return 0;
	375	}
	376
153df3c7 FF	377	#define BCM7XXX_28NM_GPHY(_oui, _name) \
	378	{ \
	379	.phy_id = (_oui), \
	380	.phy_id_mask = 0xfffffff0, \
	381	.name = _name, \
	382	.features = PHY_GBIT_FEATURES \| \
	383	SUPPORTED_Pause \| SUPPORTED_Asym_Pause, \
	384	.flags = PHY_IS_INTERNAL, \
2a9df742	385	.config_init = bcm7xxx_28nm_config_init, \
153df3c7 FF	386	.config_aneg = genphy_config_aneg, \
	387	.read_status = genphy_read_status, \
	388	.resume = bcm7xxx_28nm_resume, \
	389	.driver = { .owner = THIS_MODULE }, \
	390	}
	391
b560a58c	392	static struct phy_driver bcm7xxx_driver[] = {
430ad68f FF	393	BCM7XXX_28NM_GPHY(PHY_ID_BCM7250, "Broadcom BCM7250"),
430ad68f FF	394	BCM7XXX_28NM_GPHY(PHY_ID_BCM7364, "Broadcom BCM7364"),
153df3c7 FF	395	BCM7XXX_28NM_GPHY(PHY_ID_BCM7366, "Broadcom BCM7366"),
	396	BCM7XXX_28NM_GPHY(PHY_ID_BCM7439, "Broadcom BCM7439"),
	397	BCM7XXX_28NM_GPHY(PHY_ID_BCM7445, "Broadcom BCM7445"),
b560a58c	398	{
d068b02c PG	399	.phy_id = PHY_ID_BCM7425,
	400	.phy_id_mask = 0xfffffff0,
	401	.name = "Broadcom BCM7425",
	402	.features = PHY_GBIT_FEATURES \|
	403	SUPPORTED_Pause \| SUPPORTED_Asym_Pause,
	404	.flags = 0,
	405	.config_init = bcm7xxx_config_init,
	406	.config_aneg = genphy_config_aneg,
	407	.read_status = genphy_read_status,
	408	.suspend = bcm7xxx_suspend,
	409	.resume = bcm7xxx_config_init,
	410	.driver = { .owner = THIS_MODULE },
	411	}, {
	412	.phy_id = PHY_ID_BCM7429,
	413	.phy_id_mask = 0xfffffff0,
	414	.name = "Broadcom BCM7429",
	415	.features = PHY_GBIT_FEATURES \|
	416	SUPPORTED_Pause \| SUPPORTED_Asym_Pause,
	417	.flags = PHY_IS_INTERNAL,
	418	.config_init = bcm7xxx_config_init,
	419	.config_aneg = genphy_config_aneg,
	420	.read_status = genphy_read_status,
	421	.suspend = bcm7xxx_suspend,
	422	.resume = bcm7xxx_config_init,
	423	.driver = { .owner = THIS_MODULE },
	424	}, {
b560a58c FF	425	.phy_id = PHY_BCM_OUI_4,
	426	.phy_id_mask = 0xffff0000,
	427	.name = "Broadcom BCM7XXX 40nm",
	428	.features = PHY_GBIT_FEATURES \|
	429	SUPPORTED_Pause \| SUPPORTED_Asym_Pause,
	430	.flags = PHY_IS_INTERNAL,
	431	.config_init = bcm7xxx_config_init,
	432	.config_aneg = genphy_config_aneg,
	433	.read_status = genphy_read_status,
	434	.suspend = bcm7xxx_suspend,
	435	.resume = bcm7xxx_config_init,
	436	.driver = { .owner = THIS_MODULE },
	437	}, {
	438	.phy_id = PHY_BCM_OUI_5,
	439	.phy_id_mask = 0xffffff00,
	440	.name = "Broadcom BCM7XXX 65nm",
	441	.features = PHY_BASIC_FEATURES \|
	442	SUPPORTED_Pause \| SUPPORTED_Asym_Pause,
	443	.flags = PHY_IS_INTERNAL,
	444	.config_init = bcm7xxx_dummy_config_init,
	445	.config_aneg = genphy_config_aneg,
	446	.read_status = genphy_read_status,
	447	.suspend = bcm7xxx_suspend,
	448	.resume = bcm7xxx_config_init,
	449	.driver = { .owner = THIS_MODULE },
	450	} };
	451
	452	static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = {
430ad68f FF	453	{ PHY_ID_BCM7250, 0xfffffff0, },
430ad68f FF	454	{ PHY_ID_BCM7364, 0xfffffff0, },
b560a58c	455	{ PHY_ID_BCM7366, 0xfffffff0, },
d068b02c PG	456	{ PHY_ID_BCM7425, 0xfffffff0, },
d068b02c PG	457	{ PHY_ID_BCM7429, 0xfffffff0, },
b560a58c FF	458	{ PHY_ID_BCM7439, 0xfffffff0, },
b560a58c FF	459	{ PHY_ID_BCM7445, 0xfffffff0, },
b560a58c FF	460	{ PHY_BCM_OUI_4, 0xffff0000 },
	461	{ PHY_BCM_OUI_5, 0xffffff00 },
	462	{ }
	463	};
	464
50fd7150	465	module_phy_driver(bcm7xxx_driver);
b560a58c FF	466
	467	MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl);
	468
	469	MODULE_DESCRIPTION("Broadcom BCM7xxx internal PHY driver");
	470	MODULE_LICENSE("GPL");
	471	MODULE_AUTHOR("Broadcom Corporation");