Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* hermes.h |
2 | * | |
3 | * Driver core for the "Hermes" wireless MAC controller, as used in | |
4 | * the Lucent Orinoco and Cabletron RoamAbout cards. It should also | |
5 | * work on the hfa3841 and hfa3842 MAC controller chips used in the | |
6 | * Prism I & II chipsets. | |
7 | * | |
8 | * This is not a complete driver, just low-level access routines for | |
9 | * the MAC controller itself. | |
10 | * | |
11 | * Based on the prism2 driver from Absolute Value Systems' linux-wlan | |
12 | * project, the Linux wvlan_cs driver, Lucent's HCF-Light | |
13 | * (wvlan_hcf.c) library, and the NetBSD wireless driver. | |
14 | * | |
15 | * Copyright (C) 2000, David Gibson, Linuxcare Australia. | |
16 | * (C) Copyright David Gibson, IBM Corp. 2001-2003. | |
17 | * | |
18 | * Portions taken from hfa384x.h, Copyright (C) 1999 AbsoluteValue Systems, Inc. All Rights Reserved. | |
19 | * | |
20 | * This file distributed under the GPL, version 2. | |
21 | */ | |
22 | ||
23 | #ifndef _HERMES_H | |
24 | #define _HERMES_H | |
25 | ||
26 | /* Notes on locking: | |
27 | * | |
28 | * As a module of low level hardware access routines, there is no | |
29 | * locking. Users of this module should ensure that they serialize | |
30 | * access to the hermes_t structure, and to the hardware | |
31 | */ | |
32 | ||
1da177e4 | 33 | #include <linux/if_ether.h> |
ef846bf0 | 34 | #include <asm/io.h> |
1da177e4 LT |
35 | |
36 | /* | |
37 | * Limits and constants | |
38 | */ | |
39 | #define HERMES_ALLOC_LEN_MIN (4) | |
40 | #define HERMES_ALLOC_LEN_MAX (2400) | |
41 | #define HERMES_LTV_LEN_MAX (34) | |
42 | #define HERMES_BAP_DATALEN_MAX (4096) | |
43 | #define HERMES_BAP_OFFSET_MAX (4096) | |
44 | #define HERMES_PORTID_MAX (7) | |
45 | #define HERMES_NUMPORTS_MAX (HERMES_PORTID_MAX+1) | |
46 | #define HERMES_PDR_LEN_MAX (260) /* in bytes, from EK */ | |
47 | #define HERMES_PDA_RECS_MAX (200) /* a guess */ | |
48 | #define HERMES_PDA_LEN_MAX (1024) /* in bytes, from EK */ | |
49 | #define HERMES_SCANRESULT_MAX (35) | |
50 | #define HERMES_CHINFORESULT_MAX (8) | |
51 | #define HERMES_MAX_MULTICAST (16) | |
52 | #define HERMES_MAGIC (0x7d1f) | |
53 | ||
54 | /* | |
55 | * Hermes register offsets | |
56 | */ | |
57 | #define HERMES_CMD (0x00) | |
58 | #define HERMES_PARAM0 (0x02) | |
59 | #define HERMES_PARAM1 (0x04) | |
60 | #define HERMES_PARAM2 (0x06) | |
61 | #define HERMES_STATUS (0x08) | |
62 | #define HERMES_RESP0 (0x0A) | |
63 | #define HERMES_RESP1 (0x0C) | |
64 | #define HERMES_RESP2 (0x0E) | |
65 | #define HERMES_INFOFID (0x10) | |
66 | #define HERMES_RXFID (0x20) | |
67 | #define HERMES_ALLOCFID (0x22) | |
68 | #define HERMES_TXCOMPLFID (0x24) | |
69 | #define HERMES_SELECT0 (0x18) | |
70 | #define HERMES_OFFSET0 (0x1C) | |
71 | #define HERMES_DATA0 (0x36) | |
72 | #define HERMES_SELECT1 (0x1A) | |
73 | #define HERMES_OFFSET1 (0x1E) | |
74 | #define HERMES_DATA1 (0x38) | |
75 | #define HERMES_EVSTAT (0x30) | |
76 | #define HERMES_INTEN (0x32) | |
77 | #define HERMES_EVACK (0x34) | |
78 | #define HERMES_CONTROL (0x14) | |
79 | #define HERMES_SWSUPPORT0 (0x28) | |
80 | #define HERMES_SWSUPPORT1 (0x2A) | |
81 | #define HERMES_SWSUPPORT2 (0x2C) | |
82 | #define HERMES_AUXPAGE (0x3A) | |
83 | #define HERMES_AUXOFFSET (0x3C) | |
84 | #define HERMES_AUXDATA (0x3E) | |
85 | ||
86 | /* | |
87 | * CMD register bitmasks | |
88 | */ | |
89 | #define HERMES_CMD_BUSY (0x8000) | |
90 | #define HERMES_CMD_AINFO (0x7f00) | |
91 | #define HERMES_CMD_MACPORT (0x0700) | |
92 | #define HERMES_CMD_RECL (0x0100) | |
93 | #define HERMES_CMD_WRITE (0x0100) | |
94 | #define HERMES_CMD_PROGMODE (0x0300) | |
95 | #define HERMES_CMD_CMDCODE (0x003f) | |
96 | ||
97 | /* | |
98 | * STATUS register bitmasks | |
99 | */ | |
100 | #define HERMES_STATUS_RESULT (0x7f00) | |
101 | #define HERMES_STATUS_CMDCODE (0x003f) | |
102 | ||
103 | /* | |
104 | * OFFSET register bitmasks | |
105 | */ | |
106 | #define HERMES_OFFSET_BUSY (0x8000) | |
107 | #define HERMES_OFFSET_ERR (0x4000) | |
108 | #define HERMES_OFFSET_DATAOFF (0x0ffe) | |
109 | ||
110 | /* | |
111 | * Event register bitmasks (INTEN, EVSTAT, EVACK) | |
112 | */ | |
113 | #define HERMES_EV_TICK (0x8000) | |
114 | #define HERMES_EV_WTERR (0x4000) | |
115 | #define HERMES_EV_INFDROP (0x2000) | |
116 | #define HERMES_EV_INFO (0x0080) | |
117 | #define HERMES_EV_DTIM (0x0020) | |
118 | #define HERMES_EV_CMD (0x0010) | |
119 | #define HERMES_EV_ALLOC (0x0008) | |
120 | #define HERMES_EV_TXEXC (0x0004) | |
121 | #define HERMES_EV_TX (0x0002) | |
122 | #define HERMES_EV_RX (0x0001) | |
123 | ||
124 | /* | |
125 | * Command codes | |
126 | */ | |
127 | /*--- Controller Commands ----------------------------*/ | |
128 | #define HERMES_CMD_INIT (0x0000) | |
129 | #define HERMES_CMD_ENABLE (0x0001) | |
130 | #define HERMES_CMD_DISABLE (0x0002) | |
131 | #define HERMES_CMD_DIAG (0x0003) | |
132 | ||
133 | /*--- Buffer Mgmt Commands ---------------------------*/ | |
134 | #define HERMES_CMD_ALLOC (0x000A) | |
135 | #define HERMES_CMD_TX (0x000B) | |
136 | ||
137 | /*--- Regulate Commands ------------------------------*/ | |
138 | #define HERMES_CMD_NOTIFY (0x0010) | |
139 | #define HERMES_CMD_INQUIRE (0x0011) | |
140 | ||
141 | /*--- Configure Commands -----------------------------*/ | |
142 | #define HERMES_CMD_ACCESS (0x0021) | |
143 | #define HERMES_CMD_DOWNLD (0x0022) | |
144 | ||
145 | /*--- Serial I/O Commands ----------------------------*/ | |
146 | #define HERMES_CMD_READMIF (0x0030) | |
147 | #define HERMES_CMD_WRITEMIF (0x0031) | |
148 | ||
149 | /*--- Debugging Commands -----------------------------*/ | |
150 | #define HERMES_CMD_TEST (0x0038) | |
151 | ||
152 | ||
153 | /* Test command arguments */ | |
154 | #define HERMES_TEST_SET_CHANNEL 0x0800 | |
155 | #define HERMES_TEST_MONITOR 0x0b00 | |
156 | #define HERMES_TEST_STOP 0x0f00 | |
157 | ||
158 | /* Authentication algorithms */ | |
159 | #define HERMES_AUTH_OPEN 1 | |
160 | #define HERMES_AUTH_SHARED_KEY 2 | |
161 | ||
162 | /* WEP settings */ | |
163 | #define HERMES_WEP_PRIVACY_INVOKED 0x0001 | |
164 | #define HERMES_WEP_EXCL_UNENCRYPTED 0x0002 | |
165 | #define HERMES_WEP_HOST_ENCRYPT 0x0010 | |
166 | #define HERMES_WEP_HOST_DECRYPT 0x0080 | |
167 | ||
168 | /* Symbol hostscan options */ | |
169 | #define HERMES_HOSTSCAN_SYMBOL_5SEC 0x0001 | |
170 | #define HERMES_HOSTSCAN_SYMBOL_ONCE 0x0002 | |
171 | #define HERMES_HOSTSCAN_SYMBOL_PASSIVE 0x0040 | |
172 | #define HERMES_HOSTSCAN_SYMBOL_BCAST 0x0080 | |
173 | ||
174 | /* | |
175 | * Frame structures and constants | |
176 | */ | |
177 | ||
178 | #define HERMES_DESCRIPTOR_OFFSET 0 | |
179 | #define HERMES_802_11_OFFSET (14) | |
180 | #define HERMES_802_3_OFFSET (14+32) | |
181 | #define HERMES_802_2_OFFSET (14+32+14) | |
182 | ||
183 | #define HERMES_RXSTAT_ERR (0x0003) | |
184 | #define HERMES_RXSTAT_BADCRC (0x0001) | |
185 | #define HERMES_RXSTAT_UNDECRYPTABLE (0x0002) | |
186 | #define HERMES_RXSTAT_MACPORT (0x0700) | |
187 | #define HERMES_RXSTAT_PCF (0x1000) /* Frame was received in CF period */ | |
188 | #define HERMES_RXSTAT_MSGTYPE (0xE000) | |
189 | #define HERMES_RXSTAT_1042 (0x2000) /* RFC-1042 frame */ | |
190 | #define HERMES_RXSTAT_TUNNEL (0x4000) /* bridge-tunnel encoded frame */ | |
191 | #define HERMES_RXSTAT_WMP (0x6000) /* Wavelan-II Management Protocol frame */ | |
192 | ||
193 | struct hermes_tx_descriptor { | |
d133ae4c PR |
194 | __le16 status; |
195 | __le16 reserved1; | |
196 | __le16 reserved2; | |
197 | __le32 sw_support; | |
1da177e4 LT |
198 | u8 retry_count; |
199 | u8 tx_rate; | |
d133ae4c | 200 | __le16 tx_control; |
1da177e4 LT |
201 | } __attribute__ ((packed)); |
202 | ||
203 | #define HERMES_TXSTAT_RETRYERR (0x0001) | |
204 | #define HERMES_TXSTAT_AGEDERR (0x0002) | |
205 | #define HERMES_TXSTAT_DISCON (0x0004) | |
206 | #define HERMES_TXSTAT_FORMERR (0x0008) | |
207 | ||
208 | #define HERMES_TXCTRL_TX_OK (0x0002) /* ?? interrupt on Tx complete */ | |
209 | #define HERMES_TXCTRL_TX_EX (0x0004) /* ?? interrupt on Tx exception */ | |
210 | #define HERMES_TXCTRL_802_11 (0x0008) /* We supply 802.11 header */ | |
211 | #define HERMES_TXCTRL_ALT_RTRY (0x0020) | |
212 | ||
213 | /* Inquiry constants and data types */ | |
214 | ||
215 | #define HERMES_INQ_TALLIES (0xF100) | |
216 | #define HERMES_INQ_SCAN (0xF101) | |
217 | #define HERMES_INQ_CHANNELINFO (0xF102) | |
218 | #define HERMES_INQ_HOSTSCAN (0xF103) | |
219 | #define HERMES_INQ_HOSTSCAN_SYMBOL (0xF104) | |
220 | #define HERMES_INQ_LINKSTATUS (0xF200) | |
221 | #define HERMES_INQ_SEC_STAT_AGERE (0xF202) | |
222 | ||
223 | struct hermes_tallies_frame { | |
d133ae4c PR |
224 | __le16 TxUnicastFrames; |
225 | __le16 TxMulticastFrames; | |
226 | __le16 TxFragments; | |
227 | __le16 TxUnicastOctets; | |
228 | __le16 TxMulticastOctets; | |
229 | __le16 TxDeferredTransmissions; | |
230 | __le16 TxSingleRetryFrames; | |
231 | __le16 TxMultipleRetryFrames; | |
232 | __le16 TxRetryLimitExceeded; | |
233 | __le16 TxDiscards; | |
234 | __le16 RxUnicastFrames; | |
235 | __le16 RxMulticastFrames; | |
236 | __le16 RxFragments; | |
237 | __le16 RxUnicastOctets; | |
238 | __le16 RxMulticastOctets; | |
239 | __le16 RxFCSErrors; | |
240 | __le16 RxDiscards_NoBuffer; | |
241 | __le16 TxDiscardsWrongSA; | |
242 | __le16 RxWEPUndecryptable; | |
243 | __le16 RxMsgInMsgFragments; | |
244 | __le16 RxMsgInBadMsgFragments; | |
1da177e4 | 245 | /* Those last are probably not available in very old firmwares */ |
d133ae4c PR |
246 | __le16 RxDiscards_WEPICVError; |
247 | __le16 RxDiscards_WEPExcluded; | |
1da177e4 LT |
248 | } __attribute__ ((packed)); |
249 | ||
250 | /* Grabbed from wlan-ng - Thanks Mark... - Jean II | |
251 | * This is the result of a scan inquiry command */ | |
252 | /* Structure describing info about an Access Point */ | |
253 | struct prism2_scan_apinfo { | |
d133ae4c PR |
254 | __le16 channel; /* Channel where the AP sits */ |
255 | __le16 noise; /* Noise level */ | |
256 | __le16 level; /* Signal level */ | |
1da177e4 | 257 | u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ |
d133ae4c PR |
258 | __le16 beacon_interv; /* Beacon interval */ |
259 | __le16 capabilities; /* Capabilities */ | |
260 | __le16 essid_len; /* ESSID length */ | |
1da177e4 LT |
261 | u8 essid[32]; /* ESSID of the network */ |
262 | u8 rates[10]; /* Bit rate supported */ | |
d133ae4c PR |
263 | __le16 proberesp_rate; /* Data rate of the response frame */ |
264 | __le16 atim; /* ATIM window time, Kus (hostscan only) */ | |
1da177e4 LT |
265 | } __attribute__ ((packed)); |
266 | ||
267 | /* Same stuff for the Lucent/Agere card. | |
268 | * Thanks to h1kari <h1kari AT dachb0den.com> - Jean II */ | |
269 | struct agere_scan_apinfo { | |
d133ae4c PR |
270 | __le16 channel; /* Channel where the AP sits */ |
271 | __le16 noise; /* Noise level */ | |
272 | __le16 level; /* Signal level */ | |
1da177e4 | 273 | u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ |
d133ae4c PR |
274 | __le16 beacon_interv; /* Beacon interval */ |
275 | __le16 capabilities; /* Capabilities */ | |
1da177e4 | 276 | /* bits: 0-ess, 1-ibss, 4-privacy [wep] */ |
d133ae4c | 277 | __le16 essid_len; /* ESSID length */ |
1da177e4 LT |
278 | u8 essid[32]; /* ESSID of the network */ |
279 | } __attribute__ ((packed)); | |
280 | ||
281 | /* Moustafa: Scan structure for Symbol cards */ | |
282 | struct symbol_scan_apinfo { | |
283 | u8 channel; /* Channel where the AP sits */ | |
284 | u8 unknown1; /* 8 in 2.9x and 3.9x f/w, 0 otherwise */ | |
d133ae4c PR |
285 | __le16 noise; /* Noise level */ |
286 | __le16 level; /* Signal level */ | |
1da177e4 | 287 | u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ |
d133ae4c PR |
288 | __le16 beacon_interv; /* Beacon interval */ |
289 | __le16 capabilities; /* Capabilities */ | |
1da177e4 | 290 | /* bits: 0-ess, 1-ibss, 4-privacy [wep] */ |
d133ae4c | 291 | __le16 essid_len; /* ESSID length */ |
1da177e4 | 292 | u8 essid[32]; /* ESSID of the network */ |
d133ae4c PR |
293 | __le16 rates[5]; /* Bit rate supported */ |
294 | __le16 basic_rates; /* Basic rates bitmask */ | |
1da177e4 LT |
295 | u8 unknown2[6]; /* Always FF:FF:FF:FF:00:00 */ |
296 | u8 unknown3[8]; /* Always 0, appeared in f/w 3.91-68 */ | |
297 | } __attribute__ ((packed)); | |
298 | ||
299 | union hermes_scan_info { | |
300 | struct agere_scan_apinfo a; | |
301 | struct prism2_scan_apinfo p; | |
302 | struct symbol_scan_apinfo s; | |
303 | }; | |
304 | ||
305 | #define HERMES_LINKSTATUS_NOT_CONNECTED (0x0000) | |
306 | #define HERMES_LINKSTATUS_CONNECTED (0x0001) | |
307 | #define HERMES_LINKSTATUS_DISCONNECTED (0x0002) | |
308 | #define HERMES_LINKSTATUS_AP_CHANGE (0x0003) | |
309 | #define HERMES_LINKSTATUS_AP_OUT_OF_RANGE (0x0004) | |
310 | #define HERMES_LINKSTATUS_AP_IN_RANGE (0x0005) | |
311 | #define HERMES_LINKSTATUS_ASSOC_FAILED (0x0006) | |
312 | ||
313 | struct hermes_linkstatus { | |
d133ae4c | 314 | __le16 linkstatus; /* Link status */ |
1da177e4 LT |
315 | } __attribute__ ((packed)); |
316 | ||
317 | struct hermes_response { | |
318 | u16 status, resp0, resp1, resp2; | |
319 | }; | |
320 | ||
321 | /* "ID" structure - used for ESSID and station nickname */ | |
322 | struct hermes_idstring { | |
d133ae4c PR |
323 | __le16 len; |
324 | __le16 val[16]; | |
1da177e4 LT |
325 | } __attribute__ ((packed)); |
326 | ||
327 | struct hermes_multicast { | |
328 | u8 addr[HERMES_MAX_MULTICAST][ETH_ALEN]; | |
329 | } __attribute__ ((packed)); | |
330 | ||
331 | // #define HERMES_DEBUG_BUFFER 1 | |
332 | #define HERMES_DEBUG_BUFSIZE 4096 | |
333 | struct hermes_debug_entry { | |
334 | int bap; | |
335 | u16 id, offset; | |
336 | int cycles; | |
337 | }; | |
338 | ||
339 | #ifdef __KERNEL__ | |
340 | ||
341 | /* Timeouts */ | |
342 | #define HERMES_BAP_BUSY_TIMEOUT (10000) /* In iterations of ~1us */ | |
343 | ||
344 | /* Basic control structure */ | |
345 | typedef struct hermes { | |
346 | void __iomem *iobase; | |
347 | int reg_spacing; | |
348 | #define HERMES_16BIT_REGSPACING 0 | |
349 | #define HERMES_32BIT_REGSPACING 1 | |
350 | ||
351 | u16 inten; /* Which interrupts should be enabled? */ | |
352 | ||
353 | #ifdef HERMES_DEBUG_BUFFER | |
354 | struct hermes_debug_entry dbuf[HERMES_DEBUG_BUFSIZE]; | |
355 | unsigned long dbufp; | |
356 | unsigned long profile[HERMES_BAP_BUSY_TIMEOUT+1]; | |
357 | #endif | |
358 | } hermes_t; | |
359 | ||
360 | /* Register access convenience macros */ | |
361 | #define hermes_read_reg(hw, off) \ | |
362 | (ioread16((hw)->iobase + ( (off) << (hw)->reg_spacing ))) | |
363 | #define hermes_write_reg(hw, off, val) \ | |
364 | (iowrite16((val), (hw)->iobase + ((off) << (hw)->reg_spacing))) | |
365 | #define hermes_read_regn(hw, name) hermes_read_reg((hw), HERMES_##name) | |
366 | #define hermes_write_regn(hw, name, val) hermes_write_reg((hw), HERMES_##name, (val)) | |
367 | ||
368 | /* Function prototypes */ | |
369 | void hermes_struct_init(hermes_t *hw, void __iomem *address, int reg_spacing); | |
370 | int hermes_init(hermes_t *hw); | |
371 | int hermes_docmd_wait(hermes_t *hw, u16 cmd, u16 parm0, | |
372 | struct hermes_response *resp); | |
373 | int hermes_allocate(hermes_t *hw, u16 size, u16 *fid); | |
374 | ||
375 | int hermes_bap_pread(hermes_t *hw, int bap, void *buf, unsigned len, | |
376 | u16 id, u16 offset); | |
377 | int hermes_bap_pwrite(hermes_t *hw, int bap, const void *buf, unsigned len, | |
378 | u16 id, u16 offset); | |
379 | int hermes_read_ltv(hermes_t *hw, int bap, u16 rid, unsigned buflen, | |
380 | u16 *length, void *buf); | |
381 | int hermes_write_ltv(hermes_t *hw, int bap, u16 rid, | |
382 | u16 length, const void *value); | |
383 | ||
384 | /* Inline functions */ | |
385 | ||
386 | static inline int hermes_present(hermes_t *hw) | |
387 | { | |
388 | return hermes_read_regn(hw, SWSUPPORT0) == HERMES_MAGIC; | |
389 | } | |
390 | ||
391 | static inline void hermes_set_irqmask(hermes_t *hw, u16 events) | |
392 | { | |
393 | hw->inten = events; | |
394 | hermes_write_regn(hw, INTEN, events); | |
395 | } | |
396 | ||
397 | static inline int hermes_enable_port(hermes_t *hw, int port) | |
398 | { | |
399 | return hermes_docmd_wait(hw, HERMES_CMD_ENABLE | (port << 8), | |
400 | 0, NULL); | |
401 | } | |
402 | ||
403 | static inline int hermes_disable_port(hermes_t *hw, int port) | |
404 | { | |
405 | return hermes_docmd_wait(hw, HERMES_CMD_DISABLE | (port << 8), | |
406 | 0, NULL); | |
407 | } | |
408 | ||
409 | /* Initiate an INQUIRE command (tallies or scan). The result will come as an | |
410 | * information frame in __orinoco_ev_info() */ | |
411 | static inline int hermes_inquire(hermes_t *hw, u16 rid) | |
412 | { | |
413 | return hermes_docmd_wait(hw, HERMES_CMD_INQUIRE, rid, NULL); | |
414 | } | |
415 | ||
416 | #define HERMES_BYTES_TO_RECLEN(n) ( (((n)+1)/2) + 1 ) | |
417 | #define HERMES_RECLEN_TO_BYTES(n) ( ((n)-1) * 2 ) | |
418 | ||
419 | /* Note that for the next two, the count is in 16-bit words, not bytes */ | |
420 | static inline void hermes_read_words(struct hermes *hw, int off, void *buf, unsigned count) | |
421 | { | |
422 | off = off << hw->reg_spacing; | |
423 | ioread16_rep(hw->iobase + off, buf, count); | |
424 | } | |
425 | ||
426 | static inline void hermes_write_words(struct hermes *hw, int off, const void *buf, unsigned count) | |
427 | { | |
428 | off = off << hw->reg_spacing; | |
429 | iowrite16_rep(hw->iobase + off, buf, count); | |
430 | } | |
431 | ||
432 | static inline void hermes_clear_words(struct hermes *hw, int off, unsigned count) | |
433 | { | |
434 | unsigned i; | |
435 | ||
436 | off = off << hw->reg_spacing; | |
437 | ||
438 | for (i = 0; i < count; i++) | |
439 | iowrite16(0, hw->iobase + off); | |
440 | } | |
441 | ||
442 | #define HERMES_READ_RECORD(hw, bap, rid, buf) \ | |
443 | (hermes_read_ltv((hw),(bap),(rid), sizeof(*buf), NULL, (buf))) | |
444 | #define HERMES_WRITE_RECORD(hw, bap, rid, buf) \ | |
445 | (hermes_write_ltv((hw),(bap),(rid),HERMES_BYTES_TO_RECLEN(sizeof(*buf)),(buf))) | |
446 | ||
447 | static inline int hermes_read_wordrec(hermes_t *hw, int bap, u16 rid, u16 *word) | |
448 | { | |
d133ae4c | 449 | __le16 rec; |
1da177e4 LT |
450 | int err; |
451 | ||
452 | err = HERMES_READ_RECORD(hw, bap, rid, &rec); | |
453 | *word = le16_to_cpu(rec); | |
454 | return err; | |
455 | } | |
456 | ||
457 | static inline int hermes_write_wordrec(hermes_t *hw, int bap, u16 rid, u16 word) | |
458 | { | |
d133ae4c | 459 | __le16 rec = cpu_to_le16(word); |
1da177e4 LT |
460 | return HERMES_WRITE_RECORD(hw, bap, rid, &rec); |
461 | } | |
462 | ||
463 | #else /* ! __KERNEL__ */ | |
464 | ||
465 | /* These are provided for the benefit of userspace drivers and testing programs | |
466 | which use ioperm() or iopl() */ | |
467 | ||
468 | #define hermes_read_reg(base, off) (inw((base) + (off))) | |
469 | #define hermes_write_reg(base, off, val) (outw((val), (base) + (off))) | |
470 | ||
471 | #define hermes_read_regn(base, name) (hermes_read_reg((base), HERMES_##name)) | |
472 | #define hermes_write_regn(base, name, val) (hermes_write_reg((base), HERMES_##name, (val))) | |
473 | ||
474 | /* Note that for the next two, the count is in 16-bit words, not bytes */ | |
475 | #define hermes_read_data(base, off, buf, count) (insw((base) + (off), (buf), (count))) | |
476 | #define hermes_write_data(base, off, buf, count) (outsw((base) + (off), (buf), (count))) | |
477 | ||
478 | #endif /* ! __KERNEL__ */ | |
479 | ||
480 | #endif /* _HERMES_H */ |