projects / deliverable / linux.git / blame
| Commit | Line | Data |
|---|---|---|
| e85d0918 DD |
1 | /* zd_chip.h |
| 2 | * | |
| 3 | * This program is free software; you can redistribute it and/or modify | |
| 4 | * it under the terms of the GNU General Public License as published by | |
| 5 | * the Free Software Foundation; either version 2 of the License, or | |
| 6 | * (at your option) any later version. | |
| 7 | * | |
| 8 | * This program is distributed in the hope that it will be useful, | |
| 9 | * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| 10 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| 11 | * GNU General Public License for more details. | |
| 12 | * | |
| 13 | * You should have received a copy of the GNU General Public License | |
| 14 | * along with this program; if not, write to the Free Software | |
| 15 | * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA | |
| 16 | */ | |
| 17 | ||
| 18 | #ifndef _ZD_CHIP_H | |
| 19 | #define _ZD_CHIP_H | |
| 20 | ||
| 21 | #include "zd_types.h" | |
| 22 | #include "zd_rf.h" | |
| 23 | #include "zd_usb.h" | |
| 24 | ||
| 25 | /* Header for the Media Access Controller (MAC) and the Baseband Processor | |
| 26 | * (BBP). It appears that the ZD1211 wraps the old ZD1205 with USB glue and | |
| 27 | * adds a processor for handling the USB protocol. | |
| 28 | */ | |
| 29 | ||
| 30 | /* 8-bit hardware registers */ | |
| 31 | #define CR0 CTL_REG(0x0000) | |
| 32 | #define CR1 CTL_REG(0x0004) | |
| 33 | #define CR2 CTL_REG(0x0008) | |
| 34 | #define CR3 CTL_REG(0x000C) | |
| 35 | ||
| 36 | #define CR5 CTL_REG(0x0010) | |
| 37 | /* bit 5: if set short preamble used | |
| 38 | * bit 6: filter band - Japan channel 14 on, else off | |
| 39 | */ | |
| 40 | #define CR6 CTL_REG(0x0014) | |
| 41 | #define CR7 CTL_REG(0x0018) | |
| 42 | #define CR8 CTL_REG(0x001C) | |
| 43 | ||
| 44 | #define CR4 CTL_REG(0x0020) | |
| 45 | ||
| 46 | #define CR9 CTL_REG(0x0024) | |
| 47 | /* bit 2: antenna switch (together with CR10) */ | |
| 48 | #define CR10 CTL_REG(0x0028) | |
| 49 | /* bit 1: antenna switch (together with CR9) | |
| 50 | * RF2959 controls with CR11 radion on and off | |
| 51 | */ | |
| 52 | #define CR11 CTL_REG(0x002C) | |
| 53 | /* bit 6: TX power control for OFDM | |
| 54 | * RF2959 controls with CR10 radio on and off | |
| 55 | */ | |
| 56 | #define CR12 CTL_REG(0x0030) | |
| 57 | #define CR13 CTL_REG(0x0034) | |
| 58 | #define CR14 CTL_REG(0x0038) | |
| 59 | #define CR15 CTL_REG(0x003C) | |
| 60 | #define CR16 CTL_REG(0x0040) | |
| 61 | #define CR17 CTL_REG(0x0044) | |
| 62 | #define CR18 CTL_REG(0x0048) | |
| 63 | #define CR19 CTL_REG(0x004C) | |
| 64 | #define CR20 CTL_REG(0x0050) | |
| 65 | #define CR21 CTL_REG(0x0054) | |
| 66 | #define CR22 CTL_REG(0x0058) | |
| 67 | #define CR23 CTL_REG(0x005C) | |
| 68 | #define CR24 CTL_REG(0x0060) /* CCA threshold */ | |
| 69 | #define CR25 CTL_REG(0x0064) | |
| 70 | #define CR26 CTL_REG(0x0068) | |
| 71 | #define CR27 CTL_REG(0x006C) | |
| 72 | #define CR28 CTL_REG(0x0070) | |
| 73 | #define CR29 CTL_REG(0x0074) | |
| 74 | #define CR30 CTL_REG(0x0078) | |
| 75 | #define CR31 CTL_REG(0x007C) /* TX power control for RF in CCK mode */ | |
| 76 | #define CR32 CTL_REG(0x0080) | |
| 77 | #define CR33 CTL_REG(0x0084) | |
| 78 | #define CR34 CTL_REG(0x0088) | |
| 79 | #define CR35 CTL_REG(0x008C) | |
| 80 | #define CR36 CTL_REG(0x0090) | |
| 81 | #define CR37 CTL_REG(0x0094) | |
| 82 | #define CR38 CTL_REG(0x0098) | |
| 83 | #define CR39 CTL_REG(0x009C) | |
| 84 | #define CR40 CTL_REG(0x00A0) | |
| 85 | #define CR41 CTL_REG(0x00A4) | |
| 86 | #define CR42 CTL_REG(0x00A8) | |
| 87 | #define CR43 CTL_REG(0x00AC) | |
| 88 | #define CR44 CTL_REG(0x00B0) | |
| 89 | #define CR45 CTL_REG(0x00B4) | |
| 90 | #define CR46 CTL_REG(0x00B8) | |
| 91 | #define CR47 CTL_REG(0x00BC) /* CCK baseband gain | |
| 92 | * (patch value might be in EEPROM) | |
| 93 | */ | |
| 94 | #define CR48 CTL_REG(0x00C0) | |
| 95 | #define CR49 CTL_REG(0x00C4) | |
| 96 | #define CR50 CTL_REG(0x00C8) | |
| 97 | #define CR51 CTL_REG(0x00CC) /* TX power control for RF in 6-36M modes */ | |
| 98 | #define CR52 CTL_REG(0x00D0) /* TX power control for RF in 48M mode */ | |
| 99 | #define CR53 CTL_REG(0x00D4) /* TX power control for RF in 54M mode */ | |
| 100 | #define CR54 CTL_REG(0x00D8) | |
| 101 | #define CR55 CTL_REG(0x00DC) | |
| 102 | #define CR56 CTL_REG(0x00E0) | |
| 103 | #define CR57 CTL_REG(0x00E4) | |
| 104 | #define CR58 CTL_REG(0x00E8) | |
| 105 | #define CR59 CTL_REG(0x00EC) | |
| 106 | #define CR60 CTL_REG(0x00F0) | |
| 107 | #define CR61 CTL_REG(0x00F4) | |
| 108 | #define CR62 CTL_REG(0x00F8) | |
| 109 | #define CR63 CTL_REG(0x00FC) | |
| 110 | #define CR64 CTL_REG(0x0100) | |
| 111 | #define CR65 CTL_REG(0x0104) /* OFDM 54M calibration */ | |
| 112 | #define CR66 CTL_REG(0x0108) /* OFDM 48M calibration */ | |
| 113 | #define CR67 CTL_REG(0x010C) /* OFDM 36M calibration */ | |
| 114 | #define CR68 CTL_REG(0x0110) /* CCK calibration */ | |
| 115 | #define CR69 CTL_REG(0x0114) | |
| 116 | #define CR70 CTL_REG(0x0118) | |
| 117 | #define CR71 CTL_REG(0x011C) | |
| 118 | #define CR72 CTL_REG(0x0120) | |
| 119 | #define CR73 CTL_REG(0x0124) | |
| 120 | #define CR74 CTL_REG(0x0128) | |
| 121 | #define CR75 CTL_REG(0x012C) | |
| 122 | #define CR76 CTL_REG(0x0130) | |
| 123 | #define CR77 CTL_REG(0x0134) | |
| 124 | #define CR78 CTL_REG(0x0138) | |
| 125 | #define CR79 CTL_REG(0x013C) | |
| 126 | #define CR80 CTL_REG(0x0140) | |
| 127 | #define CR81 CTL_REG(0x0144) | |
| 128 | #define CR82 CTL_REG(0x0148) | |
| 129 | #define CR83 CTL_REG(0x014C) | |
| 130 | #define CR84 CTL_REG(0x0150) | |
| 131 | #define CR85 CTL_REG(0x0154) | |
| 132 | #define CR86 CTL_REG(0x0158) | |
| 133 | #define CR87 CTL_REG(0x015C) | |
| 134 | #define CR88 CTL_REG(0x0160) | |
| 135 | #define CR89 CTL_REG(0x0164) | |
| 136 | #define CR90 CTL_REG(0x0168) | |
| 137 | #define CR91 CTL_REG(0x016C) | |
| 138 | #define CR92 CTL_REG(0x0170) | |
| 139 | #define CR93 CTL_REG(0x0174) | |
| 140 | #define CR94 CTL_REG(0x0178) | |
| 141 | #define CR95 CTL_REG(0x017C) | |
| 142 | #define CR96 CTL_REG(0x0180) | |
| 143 | #define CR97 CTL_REG(0x0184) | |
| 144 | #define CR98 CTL_REG(0x0188) | |
| 145 | #define CR99 CTL_REG(0x018C) | |
| 146 | #define CR100 CTL_REG(0x0190) | |
| 147 | #define CR101 CTL_REG(0x0194) | |
| 148 | #define CR102 CTL_REG(0x0198) | |
| 149 | #define CR103 CTL_REG(0x019C) | |
| 150 | #define CR104 CTL_REG(0x01A0) | |
| 151 | #define CR105 CTL_REG(0x01A4) | |
| 152 | #define CR106 CTL_REG(0x01A8) | |
| 153 | #define CR107 CTL_REG(0x01AC) | |
| 154 | #define CR108 CTL_REG(0x01B0) | |
| 155 | #define CR109 CTL_REG(0x01B4) | |
| 156 | #define CR110 CTL_REG(0x01B8) | |
| 157 | #define CR111 CTL_REG(0x01BC) | |
| 158 | #define CR112 CTL_REG(0x01C0) | |
| 159 | #define CR113 CTL_REG(0x01C4) | |
| 160 | #define CR114 CTL_REG(0x01C8) | |
| 161 | #define CR115 CTL_REG(0x01CC) | |
| 162 | #define CR116 CTL_REG(0x01D0) | |
| 163 | #define CR117 CTL_REG(0x01D4) | |
| 164 | #define CR118 CTL_REG(0x01D8) | |
| 165 | #define CR119 CTL_REG(0x01DC) | |
| 166 | #define CR120 CTL_REG(0x01E0) | |
| 167 | #define CR121 CTL_REG(0x01E4) | |
| 168 | #define CR122 CTL_REG(0x01E8) | |
| 169 | #define CR123 CTL_REG(0x01EC) | |
| 170 | #define CR124 CTL_REG(0x01F0) | |
| 171 | #define CR125 CTL_REG(0x01F4) | |
| 172 | #define CR126 CTL_REG(0x01F8) | |
| 173 | #define CR127 CTL_REG(0x01FC) | |
| 174 | #define CR128 CTL_REG(0x0200) | |
| 175 | #define CR129 CTL_REG(0x0204) | |
| 176 | #define CR130 CTL_REG(0x0208) | |
| 177 | #define CR131 CTL_REG(0x020C) | |
| 178 | #define CR132 CTL_REG(0x0210) | |
| 179 | #define CR133 CTL_REG(0x0214) | |
| 180 | #define CR134 CTL_REG(0x0218) | |
| 181 | #define CR135 CTL_REG(0x021C) | |
| 182 | #define CR136 CTL_REG(0x0220) | |
| 183 | #define CR137 CTL_REG(0x0224) | |
| 184 | #define CR138 CTL_REG(0x0228) | |
| 185 | #define CR139 CTL_REG(0x022C) | |
| 186 | #define CR140 CTL_REG(0x0230) | |
| 187 | #define CR141 CTL_REG(0x0234) | |
| 188 | #define CR142 CTL_REG(0x0238) | |
| 189 | #define CR143 CTL_REG(0x023C) | |
| 190 | #define CR144 CTL_REG(0x0240) | |
| 191 | #define CR145 CTL_REG(0x0244) | |
| 192 | #define CR146 CTL_REG(0x0248) | |
| 193 | #define CR147 CTL_REG(0x024C) | |
| 194 | #define CR148 CTL_REG(0x0250) | |
| 195 | #define CR149 CTL_REG(0x0254) | |
| 196 | #define CR150 CTL_REG(0x0258) | |
| 197 | #define CR151 CTL_REG(0x025C) | |
| 198 | #define CR152 CTL_REG(0x0260) | |
| 199 | #define CR153 CTL_REG(0x0264) | |
| 200 | #define CR154 CTL_REG(0x0268) | |
| 201 | #define CR155 CTL_REG(0x026C) | |
| 202 | #define CR156 CTL_REG(0x0270) | |
| 203 | #define CR157 CTL_REG(0x0274) | |
| 204 | #define CR158 CTL_REG(0x0278) | |
| 205 | #define CR159 CTL_REG(0x027C) | |
| 206 | #define CR160 CTL_REG(0x0280) | |
| 207 | #define CR161 CTL_REG(0x0284) | |
| 208 | #define CR162 CTL_REG(0x0288) | |
| 209 | #define CR163 CTL_REG(0x028C) | |
| 210 | #define CR164 CTL_REG(0x0290) | |
| 211 | #define CR165 CTL_REG(0x0294) | |
| 212 | #define CR166 CTL_REG(0x0298) | |
| 213 | #define CR167 CTL_REG(0x029C) | |
| 214 | #define CR168 CTL_REG(0x02A0) | |
| 215 | #define CR169 CTL_REG(0x02A4) | |
| 216 | #define CR170 CTL_REG(0x02A8) | |
| 217 | #define CR171 CTL_REG(0x02AC) | |
| 218 | #define CR172 CTL_REG(0x02B0) | |
| 219 | #define CR173 CTL_REG(0x02B4) | |
| 220 | #define CR174 CTL_REG(0x02B8) | |
| 221 | #define CR175 CTL_REG(0x02BC) | |
| 222 | #define CR176 CTL_REG(0x02C0) | |
| 223 | #define CR177 CTL_REG(0x02C4) | |
| 224 | #define CR178 CTL_REG(0x02C8) | |
| 225 | #define CR179 CTL_REG(0x02CC) | |
| 226 | #define CR180 CTL_REG(0x02D0) | |
| 227 | #define CR181 CTL_REG(0x02D4) | |
| 228 | #define CR182 CTL_REG(0x02D8) | |
| 229 | #define CR183 CTL_REG(0x02DC) | |
| 230 | #define CR184 CTL_REG(0x02E0) | |
| 231 | #define CR185 CTL_REG(0x02E4) | |
| 232 | #define CR186 CTL_REG(0x02E8) | |
| 233 | #define CR187 CTL_REG(0x02EC) | |
| 234 | #define CR188 CTL_REG(0x02F0) | |
| 235 | #define CR189 CTL_REG(0x02F4) | |
| 236 | #define CR190 CTL_REG(0x02F8) | |
| 237 | #define CR191 CTL_REG(0x02FC) | |
| 238 | #define CR192 CTL_REG(0x0300) | |
| 239 | #define CR193 CTL_REG(0x0304) | |
| 240 | #define CR194 CTL_REG(0x0308) | |
| 241 | #define CR195 CTL_REG(0x030C) | |
| 242 | #define CR196 CTL_REG(0x0310) | |
| 243 | #define CR197 CTL_REG(0x0314) | |
| 244 | #define CR198 CTL_REG(0x0318) | |
| 245 | #define CR199 CTL_REG(0x031C) | |
| 246 | #define CR200 CTL_REG(0x0320) | |
| 247 | #define CR201 CTL_REG(0x0324) | |
| 248 | #define CR202 CTL_REG(0x0328) | |
| 249 | #define CR203 CTL_REG(0x032C) /* I2C bus template value & flash control */ | |
| 250 | #define CR204 CTL_REG(0x0330) | |
| 251 | #define CR205 CTL_REG(0x0334) | |
| 252 | #define CR206 CTL_REG(0x0338) | |
| 253 | #define CR207 CTL_REG(0x033C) | |
| 254 | #define CR208 CTL_REG(0x0340) | |
| 255 | #define CR209 CTL_REG(0x0344) | |
| 256 | #define CR210 CTL_REG(0x0348) | |
| 257 | #define CR211 CTL_REG(0x034C) | |
| 258 | #define CR212 CTL_REG(0x0350) | |
| 259 | #define CR213 CTL_REG(0x0354) | |
| 260 | #define CR214 CTL_REG(0x0358) | |
| 261 | #define CR215 CTL_REG(0x035C) | |
| 262 | #define CR216 CTL_REG(0x0360) | |
| 263 | #define CR217 CTL_REG(0x0364) | |
| 264 | #define CR218 CTL_REG(0x0368) | |
| 265 | #define CR219 CTL_REG(0x036C) | |
| 266 | #define CR220 CTL_REG(0x0370) | |
| 267 | #define CR221 CTL_REG(0x0374) | |
| 268 | #define CR222 CTL_REG(0x0378) | |
| 269 | #define CR223 CTL_REG(0x037C) | |
| 270 | #define CR224 CTL_REG(0x0380) | |
| 271 | #define CR225 CTL_REG(0x0384) | |
| 272 | #define CR226 CTL_REG(0x0388) | |
| 273 | #define CR227 CTL_REG(0x038C) | |
| 274 | #define CR228 CTL_REG(0x0390) | |
| 275 | #define CR229 CTL_REG(0x0394) | |
| 276 | #define CR230 CTL_REG(0x0398) | |
| 277 | #define CR231 CTL_REG(0x039C) | |
| 278 | #define CR232 CTL_REG(0x03A0) | |
| 279 | #define CR233 CTL_REG(0x03A4) | |
| 280 | #define CR234 CTL_REG(0x03A8) | |
| 281 | #define CR235 CTL_REG(0x03AC) | |
| 282 | #define CR236 CTL_REG(0x03B0) | |
| 283 | ||
| 284 | #define CR240 CTL_REG(0x03C0) | |
| 285 | /* bit 7: host-controlled RF register writes | |
| 286 | * CR241-CR245: for hardware controlled writing of RF bits, not needed for | |
| 287 | * USB | |
| 288 | */ | |
| 289 | #define CR241 CTL_REG(0x03C4) | |
| 290 | #define CR242 CTL_REG(0x03C8) | |
| 291 | #define CR243 CTL_REG(0x03CC) | |
| 292 | #define CR244 CTL_REG(0x03D0) | |
| 293 | #define CR245 CTL_REG(0x03D4) | |
| 294 | ||
| 295 | #define CR251 CTL_REG(0x03EC) /* only used for activation and deactivation of | |
| 296 | * Airoha RFs AL2230 and AL7230B | |
| 297 | */ | |
| 298 | #define CR252 CTL_REG(0x03F0) | |
| 299 | #define CR253 CTL_REG(0x03F4) | |
| 300 | #define CR254 CTL_REG(0x03F8) | |
| 301 | #define CR255 CTL_REG(0x03FC) | |
| 302 | ||
| 303 | #define CR_MAX_PHY_REG 255 | |
| 304 | ||
| 305 | /* Taken from the ZYDAS driver, not all of them are relevant for the ZSD1211 | |
| 306 | * driver. | |
| 307 | */ | |
| 308 | ||
| 309 | #define CR_RF_IF_CLK CTL_REG(0x0400) | |
| 310 | #define CR_RF_IF_DATA CTL_REG(0x0404) | |
| 311 | #define CR_PE1_PE2 CTL_REG(0x0408) | |
| 312 | #define CR_PE2_DLY CTL_REG(0x040C) | |
| 313 | #define CR_LE1 CTL_REG(0x0410) | |
| 314 | #define CR_LE2 CTL_REG(0x0414) | |
| 315 | /* Seems to enable/disable GPI (General Purpose IO?) */ | |
| 316 | #define CR_GPI_EN CTL_REG(0x0418) | |
| 317 | #define CR_RADIO_PD CTL_REG(0x042C) | |
| 318 | #define CR_RF2948_PD CTL_REG(0x042C) | |
| 319 | #define CR_ENABLE_PS_MANUAL_AGC CTL_REG(0x043C) | |
| 320 | #define CR_CONFIG_PHILIPS CTL_REG(0x0440) | |
| 321 | #define CR_SA2400_SER_AP CTL_REG(0x0444) | |
| 322 | #define CR_I2C_WRITE CTL_REG(0x0444) | |
| 323 | #define CR_SA2400_SER_RP CTL_REG(0x0448) | |
| 324 | #define CR_RADIO_PE CTL_REG(0x0458) | |
| 325 | #define CR_RST_BUS_MASTER CTL_REG(0x045C) | |
| 326 | #define CR_RFCFG CTL_REG(0x0464) | |
| 327 | #define CR_HSTSCHG CTL_REG(0x046C) | |
| 328 | #define CR_PHY_ON CTL_REG(0x0474) | |
| 329 | #define CR_RX_DELAY CTL_REG(0x0478) | |
| 330 | #define CR_RX_PE_DELAY CTL_REG(0x047C) | |
| 331 | #define CR_GPIO_1 CTL_REG(0x0490) | |
| 332 | #define CR_GPIO_2 CTL_REG(0x0494) | |
| 333 | #define CR_EncryBufMux CTL_REG(0x04A8) | |
| 334 | #define CR_PS_CTRL CTL_REG(0x0500) | |
| 335 | #define CR_ADDA_PWR_DWN CTL_REG(0x0504) | |
| 336 | #define CR_ADDA_MBIAS_WARMTIME CTL_REG(0x0508) | |
| 337 | #define CR_MAC_PS_STATE CTL_REG(0x050C) | |
| 338 | ||
| 339 | #define CR_INTERRUPT CTL_REG(0x0510) | |
| 340 | #define INT_TX_COMPLETE 0x00000001 | |
| 341 | #define INT_RX_COMPLETE 0x00000002 | |
| 342 | #define INT_RETRY_FAIL 0x00000004 | |
| 343 | #define INT_WAKEUP 0x00000008 | |
| 344 | #define INT_DTIM_NOTIFY 0x00000020 | |
| 345 | #define INT_CFG_NEXT_BCN 0x00000040 | |
| 346 | #define INT_BUS_ABORT 0x00000080 | |
| 347 | #define INT_TX_FIFO_READY 0x00000100 | |
| 348 | #define INT_UART 0x00000200 | |
| 349 | #define INT_TX_COMPLETE_EN 0x00010000 | |
| 350 | #define INT_RX_COMPLETE_EN 0x00020000 | |
| 351 | #define INT_RETRY_FAIL_EN 0x00040000 | |
| 352 | #define INT_WAKEUP_EN 0x00080000 | |
| 353 | #define INT_DTIM_NOTIFY_EN 0x00200000 | |
| 354 | #define INT_CFG_NEXT_BCN_EN 0x00400000 | |
| 355 | #define INT_BUS_ABORT_EN 0x00800000 | |
| 356 | #define INT_TX_FIFO_READY_EN 0x01000000 | |
| 357 | #define INT_UART_EN 0x02000000 | |
| 358 | ||
| 359 | #define CR_TSF_LOW_PART CTL_REG(0x0514) | |
| 360 | #define CR_TSF_HIGH_PART CTL_REG(0x0518) | |
| 361 | ||
| 362 | /* Following three values are in time units (1024us) | |
| 363 | * Following condition must be met: | |
| 364 | * atim < tbtt < bcn | |
| 365 | */ | |
| 366 | #define CR_ATIM_WND_PERIOD CTL_REG(0x051C) | |
| 367 | #define CR_BCN_INTERVAL CTL_REG(0x0520) | |
| 368 | #define CR_PRE_TBTT CTL_REG(0x0524) | |
| 369 | /* in units of TU(1024us) */ | |
| 370 | ||
| 371 | /* for UART support */ | |
| 372 | #define CR_UART_RBR_THR_DLL CTL_REG(0x0540) | |
| 373 | #define CR_UART_DLM_IER CTL_REG(0x0544) | |
| 374 | #define CR_UART_IIR_FCR CTL_REG(0x0548) | |
| 375 | #define CR_UART_LCR CTL_REG(0x054c) | |
| 376 | #define CR_UART_MCR CTL_REG(0x0550) | |
| 377 | #define CR_UART_LSR CTL_REG(0x0554) | |
| 378 | #define CR_UART_MSR CTL_REG(0x0558) | |
| 379 | #define CR_UART_ECR CTL_REG(0x055c) | |
| 380 | #define CR_UART_STATUS CTL_REG(0x0560) | |
| 381 | ||
| 382 | #define CR_PCI_TX_ADDR_P1 CTL_REG(0x0600) | |
| 383 | #define CR_PCI_TX_AddR_P2 CTL_REG(0x0604) | |
| 384 | #define CR_PCI_RX_AddR_P1 CTL_REG(0x0608) | |
| 385 | #define CR_PCI_RX_AddR_P2 CTL_REG(0x060C) | |
| 386 | ||
| 387 | /* must be overwritten if custom MAC address will be used */ | |
| 388 | #define CR_MAC_ADDR_P1 CTL_REG(0x0610) | |
| 389 | #define CR_MAC_ADDR_P2 CTL_REG(0x0614) | |
| 390 | #define CR_BSSID_P1 CTL_REG(0x0618) | |
| 391 | #define CR_BSSID_P2 CTL_REG(0x061C) | |
| 392 | #define CR_BCN_PLCP_CFG CTL_REG(0x0620) | |
| 393 | #define CR_GROUP_HASH_P1 CTL_REG(0x0624) | |
| 394 | #define CR_GROUP_HASH_P2 CTL_REG(0x0628) | |
| 395 | #define CR_RX_TIMEOUT CTL_REG(0x062C) | |
| 396 | ||
| 397 | /* Basic rates supported by the BSS. When producing ACK or CTS messages, the | |
| 398 | * device will use a rate in this table that is less than or equal to the rate | |
| 399 | * of the incoming frame which prompted the response */ | |
| 400 | #define CR_BASIC_RATE_TBL CTL_REG(0x0630) | |
| 401 | #define CR_RATE_1M 0x0001 /* 802.11b */ | |
| 402 | #define CR_RATE_2M 0x0002 /* 802.11b */ | |
| 403 | #define CR_RATE_5_5M 0x0004 /* 802.11b */ | |
| 404 | #define CR_RATE_11M 0x0008 /* 802.11b */ | |
| 405 | #define CR_RATE_6M 0x0100 /* 802.11g */ | |
| 406 | #define CR_RATE_9M 0x0200 /* 802.11g */ | |
| 407 | #define CR_RATE_12M 0x0400 /* 802.11g */ | |
| 408 | #define CR_RATE_18M 0x0800 /* 802.11g */ | |
| 409 | #define CR_RATE_24M 0x1000 /* 802.11g */ | |
| 410 | #define CR_RATE_36M 0x2000 /* 802.11g */ | |
| 411 | #define CR_RATE_48M 0x4000 /* 802.11g */ | |
| 412 | #define CR_RATE_54M 0x8000 /* 802.11g */ | |
| 413 | #define CR_RATES_80211G 0xff00 | |
| 414 | #define CR_RATES_80211B 0x000f | |
| 415 | ||
| 416 | /* Mandatory rates required in the BSS. When producing ACK or CTS messages, if | |
| 417 | * the device could not find an appropriate rate in CR_BASIC_RATE_TBL, it will | |
| 418 | * look for a rate in this table that is less than or equal to the rate of | |
| 419 | * the incoming frame. */ | |
| 420 | #define CR_MANDATORY_RATE_TBL CTL_REG(0x0634) | |
| 421 | #define CR_RTS_CTS_RATE CTL_REG(0x0638) | |
| 422 | ||
| 423 | #define CR_WEP_PROTECT CTL_REG(0x063C) | |
| 424 | #define CR_RX_THRESHOLD CTL_REG(0x0640) | |
| 425 | ||
| 426 | /* register for controlling the LEDS */ | |
| 427 | #define CR_LED CTL_REG(0x0644) | |
| 428 | /* masks for controlling LEDs */ | |
| 429 | #define LED1 0x0100 | |
| 430 | #define LED2 0x0200 | |
| 431 | ||
| 432 | /* Seems to indicate that the configuration is over. | |
| 433 | */ | |
| 434 | #define CR_AFTER_PNP CTL_REG(0x0648) | |
| 435 | #define CR_ACK_TIME_80211 CTL_REG(0x0658) | |
| 436 | ||
| 437 | #define CR_RX_OFFSET CTL_REG(0x065c) | |
| 438 | ||
| 439 | #define CR_PHY_DELAY CTL_REG(0x066C) | |
| 440 | #define CR_BCN_FIFO CTL_REG(0x0670) | |
| 441 | #define CR_SNIFFER_ON CTL_REG(0x0674) | |
| 442 | ||
| 443 | #define CR_ENCRYPTION_TYPE CTL_REG(0x0678) | |
| 444 | #define NO_WEP 0 | |
| 445 | #define WEP64 1 | |
| 446 | #define WEP128 5 | |
| 447 | #define WEP256 6 | |
| 448 | #define ENC_SNIFFER 8 | |
| 449 | ||
| 450 | #define CR_ZD1211_RETRY_MAX CTL_REG(0x067C) | |
| 451 | ||
| 452 | #define CR_REG1 CTL_REG(0x0680) | |
| 453 | /* Setting the bit UNLOCK_PHY_REGS disallows the write access to physical | |
| 454 | * registers, so one could argue it is a LOCK bit. But calling it | |
| 455 | * LOCK_PHY_REGS makes it confusing. | |
| 456 | */ | |
| 457 | #define UNLOCK_PHY_REGS 0x0080 | |
| 458 | ||
| 459 | #define CR_DEVICE_STATE CTL_REG(0x0684) | |
| 460 | #define CR_UNDERRUN_CNT CTL_REG(0x0688) | |
| 461 | ||
| 462 | #define CR_RX_FILTER CTL_REG(0x068c) | |
| 463 | #define RX_FILTER_ASSOC_RESPONSE 0x0002 | |
| 71eae25e | 464 | #define RX_FILTER_REASSOC_RESPONSE 0x0008 |
| e85d0918 DD |
465 | #define RX_FILTER_PROBE_RESPONSE 0x0020 |
| 466 | #define RX_FILTER_BEACON 0x0100 | |
| 71eae25e | 467 | #define RX_FILTER_DISASSOC 0x0400 |
| e85d0918 | 468 | #define RX_FILTER_AUTH 0x0800 |
| fde627b5 UK |
469 | #define AP_RX_FILTER 0x0400feff |
| 470 | #define STA_RX_FILTER 0x0000ffff | |
| 471 | ||
| 71eae25e | 472 | /* Monitor mode sets filter to 0xfffff */ |
| e85d0918 DD |
473 | |
| 474 | #define CR_ACK_TIMEOUT_EXT CTL_REG(0x0690) | |
| 475 | #define CR_BCN_FIFO_SEMAPHORE CTL_REG(0x0694) | |
| 98227a90 | 476 | |
| e85d0918 | 477 | #define CR_IFS_VALUE CTL_REG(0x0698) |
| 98227a90 DD |
478 | #define IFS_VALUE_DIFS_SH 0 |
| 479 | #define IFS_VALUE_EIFS_SH 12 | |
| 480 | #define IFS_VALUE_SIFS_SH 24 | |
| 481 | #define IFS_VALUE_DEFAULT (( 50 << IFS_VALUE_DIFS_SH) | \ | |
| 482 | (1148 << IFS_VALUE_EIFS_SH) | \ | |
| 483 | ( 10 << IFS_VALUE_SIFS_SH)) | |
| 484 | ||
| e85d0918 DD |
485 | #define CR_RX_TIME_OUT CTL_REG(0x069C) |
| 486 | #define CR_TOTAL_RX_FRM CTL_REG(0x06A0) | |
| 487 | #define CR_CRC32_CNT CTL_REG(0x06A4) | |
| 488 | #define CR_CRC16_CNT CTL_REG(0x06A8) | |
| 489 | #define CR_DECRYPTION_ERR_UNI CTL_REG(0x06AC) | |
| 490 | #define CR_RX_FIFO_OVERRUN CTL_REG(0x06B0) | |
| 491 | ||
| 492 | #define CR_DECRYPTION_ERR_MUL CTL_REG(0x06BC) | |
| 493 | ||
| 494 | #define CR_NAV_CNT CTL_REG(0x06C4) | |
| 495 | #define CR_NAV_CCA CTL_REG(0x06C8) | |
| 496 | #define CR_RETRY_CNT CTL_REG(0x06CC) | |
| 497 | ||
| 498 | #define CR_READ_TCB_ADDR CTL_REG(0x06E8) | |
| 499 | #define CR_READ_RFD_ADDR CTL_REG(0x06EC) | |
| 500 | #define CR_CWMIN_CWMAX CTL_REG(0x06F0) | |
| 501 | #define CR_TOTAL_TX_FRM CTL_REG(0x06F4) | |
| 502 | ||
| 503 | /* CAM: Continuous Access Mode (power management) */ | |
| 504 | #define CR_CAM_MODE CTL_REG(0x0700) | |
| 505 | #define CR_CAM_ROLL_TB_LOW CTL_REG(0x0704) | |
| 506 | #define CR_CAM_ROLL_TB_HIGH CTL_REG(0x0708) | |
| 507 | #define CR_CAM_ADDRESS CTL_REG(0x070C) | |
| 508 | #define CR_CAM_DATA CTL_REG(0x0710) | |
| 509 | ||
| 510 | #define CR_ROMDIR CTL_REG(0x0714) | |
| 511 | ||
| 512 | #define CR_DECRY_ERR_FLG_LOW CTL_REG(0x0714) | |
| 513 | #define CR_DECRY_ERR_FLG_HIGH CTL_REG(0x0718) | |
| 514 | ||
| 515 | #define CR_WEPKEY0 CTL_REG(0x0720) | |
| 516 | #define CR_WEPKEY1 CTL_REG(0x0724) | |
| 517 | #define CR_WEPKEY2 CTL_REG(0x0728) | |
| 518 | #define CR_WEPKEY3 CTL_REG(0x072C) | |
| 519 | #define CR_WEPKEY4 CTL_REG(0x0730) | |
| 520 | #define CR_WEPKEY5 CTL_REG(0x0734) | |
| 521 | #define CR_WEPKEY6 CTL_REG(0x0738) | |
| 522 | #define CR_WEPKEY7 CTL_REG(0x073C) | |
| 523 | #define CR_WEPKEY8 CTL_REG(0x0740) | |
| 524 | #define CR_WEPKEY9 CTL_REG(0x0744) | |
| 525 | #define CR_WEPKEY10 CTL_REG(0x0748) | |
| 526 | #define CR_WEPKEY11 CTL_REG(0x074C) | |
| 527 | #define CR_WEPKEY12 CTL_REG(0x0750) | |
| 528 | #define CR_WEPKEY13 CTL_REG(0x0754) | |
| 529 | #define CR_WEPKEY14 CTL_REG(0x0758) | |
| 530 | #define CR_WEPKEY15 CTL_REG(0x075c) | |
| 531 | #define CR_TKIP_MODE CTL_REG(0x0760) | |
| 532 | ||
| 533 | #define CR_EEPROM_PROTECT0 CTL_REG(0x0758) | |
| 534 | #define CR_EEPROM_PROTECT1 CTL_REG(0x075C) | |
| 535 | ||
| 536 | #define CR_DBG_FIFO_RD CTL_REG(0x0800) | |
| 537 | #define CR_DBG_SELECT CTL_REG(0x0804) | |
| 538 | #define CR_FIFO_Length CTL_REG(0x0808) | |
| 539 | ||
| 540 | ||
| 541 | #define CR_RSSI_MGC CTL_REG(0x0810) | |
| 542 | ||
| 543 | #define CR_PON CTL_REG(0x0818) | |
| 544 | #define CR_RX_ON CTL_REG(0x081C) | |
| 545 | #define CR_TX_ON CTL_REG(0x0820) | |
| 546 | #define CR_CHIP_EN CTL_REG(0x0824) | |
| 547 | #define CR_LO_SW CTL_REG(0x0828) | |
| 548 | #define CR_TXRX_SW CTL_REG(0x082C) | |
| 549 | #define CR_S_MD CTL_REG(0x0830) | |
| 550 | ||
| 551 | #define CR_USB_DEBUG_PORT CTL_REG(0x0888) | |
| 552 | ||
| 553 | #define CR_ZD1211B_TX_PWR_CTL1 CTL_REG(0x0b00) | |
| 554 | #define CR_ZD1211B_TX_PWR_CTL2 CTL_REG(0x0b04) | |
| 555 | #define CR_ZD1211B_TX_PWR_CTL3 CTL_REG(0x0b08) | |
| 556 | #define CR_ZD1211B_TX_PWR_CTL4 CTL_REG(0x0b0c) | |
| 557 | #define CR_ZD1211B_AIFS_CTL1 CTL_REG(0x0b10) | |
| 558 | #define CR_ZD1211B_AIFS_CTL2 CTL_REG(0x0b14) | |
| 559 | #define CR_ZD1211B_TXOP CTL_REG(0x0b20) | |
| 560 | #define CR_ZD1211B_RETRY_MAX CTL_REG(0x0b28) | |
| 561 | ||
| e85d0918 DD |
562 | #define CWIN_SIZE 0x007f043f |
| 563 | ||
| 564 | ||
| 565 | #define HWINT_ENABLED 0x004f0000 | |
| 566 | #define HWINT_DISABLED 0 | |
| 567 | ||
| 568 | #define E2P_PWR_INT_GUARD 8 | |
| 569 | #define E2P_CHANNEL_COUNT 14 | |
| 570 | ||
| 571 | /* If you compare this addresses with the ZYDAS orignal driver, please notify | |
| 572 | * that we use word mapping for the EEPROM. | |
| 573 | */ | |
| 574 | ||
| 575 | /* | |
| 576 | * Upper 16 bit contains the regulatory domain. | |
| 577 | */ | |
| 578 | #define E2P_SUBID E2P_REG(0x00) | |
| 579 | #define E2P_POD E2P_REG(0x02) | |
| 580 | #define E2P_MAC_ADDR_P1 E2P_REG(0x04) | |
| 581 | #define E2P_MAC_ADDR_P2 E2P_REG(0x06) | |
| 582 | #define E2P_PWR_CAL_VALUE1 E2P_REG(0x08) | |
| 583 | #define E2P_PWR_CAL_VALUE2 E2P_REG(0x0a) | |
| 584 | #define E2P_PWR_CAL_VALUE3 E2P_REG(0x0c) | |
| 585 | #define E2P_PWR_CAL_VALUE4 E2P_REG(0x0e) | |
| 586 | #define E2P_PWR_INT_VALUE1 E2P_REG(0x10) | |
| 587 | #define E2P_PWR_INT_VALUE2 E2P_REG(0x12) | |
| 588 | #define E2P_PWR_INT_VALUE3 E2P_REG(0x14) | |
| 589 | #define E2P_PWR_INT_VALUE4 E2P_REG(0x16) | |
| 590 | ||
| 591 | /* Contains a bit for each allowed channel. It gives for Europe (ETSI 0x30) | |
| 592 | * also only 11 channels. */ | |
| 593 | #define E2P_ALLOWED_CHANNEL E2P_REG(0x18) | |
| 594 | ||
| 595 | #define E2P_PHY_REG E2P_REG(0x1a) | |
| 596 | #define E2P_DEVICE_VER E2P_REG(0x20) | |
| 597 | #define E2P_36M_CAL_VALUE1 E2P_REG(0x28) | |
| 598 | #define E2P_36M_CAL_VALUE2 E2P_REG(0x2a) | |
| 599 | #define E2P_36M_CAL_VALUE3 E2P_REG(0x2c) | |
| 600 | #define E2P_36M_CAL_VALUE4 E2P_REG(0x2e) | |
| 601 | #define E2P_11A_INT_VALUE1 E2P_REG(0x30) | |
| 602 | #define E2P_11A_INT_VALUE2 E2P_REG(0x32) | |
| 603 | #define E2P_11A_INT_VALUE3 E2P_REG(0x34) | |
| 604 | #define E2P_11A_INT_VALUE4 E2P_REG(0x36) | |
| 605 | #define E2P_48M_CAL_VALUE1 E2P_REG(0x38) | |
| 606 | #define E2P_48M_CAL_VALUE2 E2P_REG(0x3a) | |
| 607 | #define E2P_48M_CAL_VALUE3 E2P_REG(0x3c) | |
| 608 | #define E2P_48M_CAL_VALUE4 E2P_REG(0x3e) | |
| 609 | #define E2P_48M_INT_VALUE1 E2P_REG(0x40) | |
| 610 | #define E2P_48M_INT_VALUE2 E2P_REG(0x42) | |
| 611 | #define E2P_48M_INT_VALUE3 E2P_REG(0x44) | |
| 612 | #define E2P_48M_INT_VALUE4 E2P_REG(0x46) | |
| 613 | #define E2P_54M_CAL_VALUE1 E2P_REG(0x48) /* ??? */ | |
| 614 | #define E2P_54M_CAL_VALUE2 E2P_REG(0x4a) | |
| 615 | #define E2P_54M_CAL_VALUE3 E2P_REG(0x4c) | |
| 616 | #define E2P_54M_CAL_VALUE4 E2P_REG(0x4e) | |
| 617 | #define E2P_54M_INT_VALUE1 E2P_REG(0x50) | |
| 618 | #define E2P_54M_INT_VALUE2 E2P_REG(0x52) | |
| 619 | #define E2P_54M_INT_VALUE3 E2P_REG(0x54) | |
| 620 | #define E2P_54M_INT_VALUE4 E2P_REG(0x56) | |
| 621 | ||
| 622 | /* All 16 bit values */ | |
| 623 | #define FW_FIRMWARE_VER FW_REG(0) | |
| 624 | /* non-zero if USB high speed connection */ | |
| 625 | #define FW_USB_SPEED FW_REG(1) | |
| 626 | #define FW_FIX_TX_RATE FW_REG(2) | |
| 627 | /* Seems to be able to control LEDs over the firmware */ | |
| 628 | #define FW_LINK_STATUS FW_REG(3) | |
| 629 | #define FW_SOFT_RESET FW_REG(4) | |
| 630 | #define FW_FLASH_CHK FW_REG(5) | |
| 631 | ||
| 632 | enum { | |
| 633 | CR_BASE_OFFSET = 0x9000, | |
| 634 | FW_START_OFFSET = 0xee00, | |
| 635 | FW_BASE_ADDR_OFFSET = FW_START_OFFSET + 0x1d, | |
| 636 | EEPROM_START_OFFSET = 0xf800, | |
| 637 | EEPROM_SIZE = 0x800, /* words */ | |
| 638 | LOAD_CODE_SIZE = 0xe, /* words */ | |
| 639 | LOAD_VECT_SIZE = 0x10000 - 0xfff7, /* words */ | |
| 640 | EEPROM_REGS_OFFSET = LOAD_CODE_SIZE + LOAD_VECT_SIZE, | |
| d066c219 | 641 | EEPROM_REGS_SIZE = 0x7e, /* words */ |
| e85d0918 DD |
642 | E2P_BASE_OFFSET = EEPROM_START_OFFSET + |
| 643 | EEPROM_REGS_OFFSET, | |
| 644 | }; | |
| 645 | ||
| 646 | #define FW_REG_TABLE_ADDR USB_ADDR(FW_START_OFFSET + 0x1d) | |
| 647 | ||
| 648 | enum { | |
| 649 | /* indices for ofdm_cal_values */ | |
| 650 | OFDM_36M_INDEX = 0, | |
| 651 | OFDM_48M_INDEX = 1, | |
| 652 | OFDM_54M_INDEX = 2, | |
| 653 | }; | |
| 654 | ||
| 655 | struct zd_chip { | |
| 656 | struct zd_usb usb; | |
| 657 | struct zd_rf rf; | |
| 658 | struct mutex mutex; | |
| 659 | u8 e2p_mac[ETH_ALEN]; | |
| 660 | /* EepSetPoint in the vendor driver */ | |
| 661 | u8 pwr_cal_values[E2P_CHANNEL_COUNT]; | |
| 662 | /* integration values in the vendor driver */ | |
| 663 | u8 pwr_int_values[E2P_CHANNEL_COUNT]; | |
| 664 | /* SetPointOFDM in the vendor driver */ | |
| 665 | u8 ofdm_cal_values[3][E2P_CHANNEL_COUNT]; | |
| 666 | u8 pa_type:4, patch_cck_gain:1, patch_cr157:1, patch_6m_band_edge:1, | |
| 20fe2176 | 667 | new_phy_layout:1, is_zd1211b:1; |
| e85d0918 DD |
668 | }; |
| 669 | ||
| 670 | static inline struct zd_chip *zd_usb_to_chip(struct zd_usb *usb) | |
| 671 | { | |
| 672 | return container_of(usb, struct zd_chip, usb); | |
| 673 | } | |
| 674 | ||
| 675 | static inline struct zd_chip *zd_rf_to_chip(struct zd_rf *rf) | |
| 676 | { | |
| 677 | return container_of(rf, struct zd_chip, rf); | |
| 678 | } | |
| 679 | ||
| 680 | #define zd_chip_dev(chip) (&(chip)->usb.intf->dev) | |
| 681 | ||
| 682 | void zd_chip_init(struct zd_chip *chip, | |
| 683 | struct net_device *netdev, | |
| 684 | struct usb_interface *intf); | |
| 685 | void zd_chip_clear(struct zd_chip *chip); | |
| 686 | int zd_chip_init_hw(struct zd_chip *chip, u8 device_type); | |
| 687 | int zd_chip_reset(struct zd_chip *chip); | |
| 688 | ||
| 689 | static inline int zd_ioread16v_locked(struct zd_chip *chip, u16 *values, | |
| 690 | const zd_addr_t *addresses, | |
| 691 | unsigned int count) | |
| 692 | { | |
| 693 | ZD_ASSERT(mutex_is_locked(&chip->mutex)); | |
| 694 | return zd_usb_ioread16v(&chip->usb, values, addresses, count); | |
| 695 | } | |
| 696 | ||
| 697 | static inline int zd_ioread16_locked(struct zd_chip *chip, u16 *value, | |
| 698 | const zd_addr_t addr) | |
| 699 | { | |
| 700 | ZD_ASSERT(mutex_is_locked(&chip->mutex)); | |
| 701 | return zd_usb_ioread16(&chip->usb, value, addr); | |
| 702 | } | |
| 703 | ||
| 704 | int zd_ioread32v_locked(struct zd_chip *chip, u32 *values, | |
| 705 | const zd_addr_t *addresses, unsigned int count); | |
| 706 | ||
| 707 | static inline int zd_ioread32_locked(struct zd_chip *chip, u32 *value, | |
| 708 | const zd_addr_t addr) | |
| 709 | { | |
| 710 | return zd_ioread32v_locked(chip, value, (const zd_addr_t *)&addr, 1); | |
| 711 | } | |
| 712 | ||
| 713 | static inline int zd_iowrite16_locked(struct zd_chip *chip, u16 value, | |
| 714 | zd_addr_t addr) | |
| 715 | { | |
| 716 | struct zd_ioreq16 ioreq; | |
| 717 | ||
| 718 | ZD_ASSERT(mutex_is_locked(&chip->mutex)); | |
| 719 | ioreq.addr = addr; | |
| 720 | ioreq.value = value; | |
| 721 | ||
| 722 | return zd_usb_iowrite16v(&chip->usb, &ioreq, 1); | |
| 723 | } | |
| 724 | ||
| 725 | int zd_iowrite16a_locked(struct zd_chip *chip, | |
| 726 | const struct zd_ioreq16 *ioreqs, unsigned int count); | |
| 727 | ||
| 728 | int _zd_iowrite32v_locked(struct zd_chip *chip, const struct zd_ioreq32 *ioreqs, | |
| 729 | unsigned int count); | |
| 730 | ||
| 731 | static inline int zd_iowrite32_locked(struct zd_chip *chip, u32 value, | |
| 732 | zd_addr_t addr) | |
| 733 | { | |
| 734 | struct zd_ioreq32 ioreq; | |
| 735 | ||
| 736 | ioreq.addr = addr; | |
| 737 | ioreq.value = value; | |
| 738 | ||
| 739 | return _zd_iowrite32v_locked(chip, &ioreq, 1); | |
| 740 | } | |
| 741 | ||
| 742 | int zd_iowrite32a_locked(struct zd_chip *chip, | |
| 743 | const struct zd_ioreq32 *ioreqs, unsigned int count); | |
| 744 | ||
| 745 | static inline int zd_rfwrite_locked(struct zd_chip *chip, u32 value, u8 bits) | |
| 746 | { | |
| 747 | ZD_ASSERT(mutex_is_locked(&chip->mutex)); | |
| 748 | return zd_usb_rfwrite(&chip->usb, value, bits); | |
| 749 | } | |
| 750 | ||
| ec62bd91 DD |
751 | int zd_rfwrite_cr_locked(struct zd_chip *chip, u32 value); |
| 752 | ||
| e85d0918 DD |
753 | int zd_rfwritev_locked(struct zd_chip *chip, |
| 754 | const u32* values, unsigned int count, u8 bits); | |
| 20fe2176 DD |
755 | int zd_rfwritev_cr_locked(struct zd_chip *chip, |
| 756 | const u32* values, unsigned int count); | |
| e85d0918 DD |
757 | |
| 758 | /* Locking functions for reading and writing registers. | |
| 759 | * The different parameters are intentional. | |
| 760 | */ | |
| 761 | int zd_ioread16(struct zd_chip *chip, zd_addr_t addr, u16 *value); | |
| 762 | int zd_iowrite16(struct zd_chip *chip, zd_addr_t addr, u16 value); | |
| 763 | int zd_ioread32(struct zd_chip *chip, zd_addr_t addr, u32 *value); | |
| 764 | int zd_iowrite32(struct zd_chip *chip, zd_addr_t addr, u32 value); | |
| 765 | int zd_ioread32v(struct zd_chip *chip, const zd_addr_t *addresses, | |
| 766 | u32 *values, unsigned int count); | |
| 767 | int zd_iowrite32a(struct zd_chip *chip, const struct zd_ioreq32 *ioreqs, | |
| 768 | unsigned int count); | |
| 769 | ||
| 770 | int zd_chip_set_channel(struct zd_chip *chip, u8 channel); | |
| 771 | static inline u8 _zd_chip_get_channel(struct zd_chip *chip) | |
| 772 | { | |
| 773 | return chip->rf.channel; | |
| 774 | } | |
| 775 | u8 zd_chip_get_channel(struct zd_chip *chip); | |
| 776 | int zd_read_regdomain(struct zd_chip *chip, u8 *regdomain); | |
| 777 | void zd_get_e2p_mac_addr(struct zd_chip *chip, u8 *mac_addr); | |
| 778 | int zd_read_mac_addr(struct zd_chip *chip, u8 *mac_addr); | |
| 779 | int zd_write_mac_addr(struct zd_chip *chip, const u8 *mac_addr); | |
| 780 | int zd_chip_switch_radio_on(struct zd_chip *chip); | |
| 781 | int zd_chip_switch_radio_off(struct zd_chip *chip); | |
| 782 | int zd_chip_enable_int(struct zd_chip *chip); | |
| 783 | void zd_chip_disable_int(struct zd_chip *chip); | |
| 784 | int zd_chip_enable_rx(struct zd_chip *chip); | |
| 785 | void zd_chip_disable_rx(struct zd_chip *chip); | |
| 786 | int zd_chip_enable_hwint(struct zd_chip *chip); | |
| 787 | int zd_chip_disable_hwint(struct zd_chip *chip); | |
| 788 | ||
| 789 | static inline int zd_get_encryption_type(struct zd_chip *chip, u32 *type) | |
| 790 | { | |
| 791 | return zd_ioread32(chip, CR_ENCRYPTION_TYPE, type); | |
| 792 | } | |
| 793 | ||
| 794 | static inline int zd_set_encryption_type(struct zd_chip *chip, u32 type) | |
| 795 | { | |
| 796 | return zd_iowrite32(chip, CR_ENCRYPTION_TYPE, type); | |
| 797 | } | |
| 798 | ||
| 799 | static inline int zd_chip_get_basic_rates(struct zd_chip *chip, u16 *cr_rates) | |
| 800 | { | |
| 801 | return zd_ioread16(chip, CR_BASIC_RATE_TBL, cr_rates); | |
| 802 | } | |
| 803 | ||
| 804 | int zd_chip_set_basic_rates(struct zd_chip *chip, u16 cr_rates); | |
| 805 | ||
| 806 | static inline int zd_chip_set_rx_filter(struct zd_chip *chip, u32 filter) | |
| 807 | { | |
| 808 | return zd_iowrite32(chip, CR_RX_FILTER, filter); | |
| 809 | } | |
| 810 | ||
| 811 | int zd_chip_lock_phy_regs(struct zd_chip *chip); | |
| 812 | int zd_chip_unlock_phy_regs(struct zd_chip *chip); | |
| 813 | ||
| 814 | enum led_status { | |
| 815 | LED_OFF = 0, | |
| 816 | LED_ON = 1, | |
| 817 | LED_FLIP = 2, | |
| 818 | LED_STATUS = 3, | |
| 819 | }; | |
| 820 | ||
| 821 | int zd_chip_led_status(struct zd_chip *chip, int led, enum led_status status); | |
| 822 | int zd_chip_led_flip(struct zd_chip *chip, int led, | |
| 823 | const unsigned int *phases_msecs, unsigned int count); | |
| 824 | ||
| 825 | int zd_set_beacon_interval(struct zd_chip *chip, u32 interval); | |
| 826 | ||
| 827 | static inline int zd_get_beacon_interval(struct zd_chip *chip, u32 *interval) | |
| 828 | { | |
| 829 | return zd_ioread32(chip, CR_BCN_INTERVAL, interval); | |
| 830 | } | |
| 831 | ||
| 832 | struct rx_status; | |
| 833 | ||
| 834 | u8 zd_rx_qual_percent(const void *rx_frame, unsigned int size, | |
| 835 | const struct rx_status *status); | |
| 836 | u8 zd_rx_strength_percent(u8 rssi); | |
| 837 | ||
| 838 | u16 zd_rx_rate(const void *rx_frame, const struct rx_status *status); | |
| 839 | ||
| 840 | #endif /* _ZD_CHIP_H */ |