Commit | Line | Data |
---|---|---|
7be2c7c9 | 1 | # |
c58411e9 AZ |
2 | # RTC class/drivers configuration |
3 | # | |
4 | ||
5 | config RTC_LIB | |
b4d246b1 | 6 | bool |
0c86edc0 | 7 | |
bb35fb20 | 8 | menuconfig RTC_CLASS |
b4d246b1 | 9 | bool "Real Time Clock" |
0c86edc0 | 10 | default n |
3369465e | 11 | depends on !S390 && !UML |
0c86edc0 AZ |
12 | select RTC_LIB |
13 | help | |
14 | Generic RTC class support. If you say yes here, you will | |
15 | be allowed to plug one or more RTCs to your system. You will | |
27ae4104 | 16 | probably want to enable one or more of the interfaces below. |
0c86edc0 | 17 | |
bb35fb20 JE |
18 | if RTC_CLASS |
19 | ||
0c86edc0 | 20 | config RTC_HCTOSYS |
7ca1d488 | 21 | bool "Set system time from RTC on startup and resume" |
0c86edc0 AZ |
22 | default y |
23 | help | |
7ca1d488 DB |
24 | If you say yes here, the system time (wall clock) will be set using |
25 | the value read from a specified RTC device. This is useful to avoid | |
26 | unnecessary fsck runs at boot time, and to network better. | |
0c86edc0 | 27 | |
023f333a JG |
28 | config RTC_SYSTOHC |
29 | bool "Set the RTC time based on NTP synchronization" | |
30 | default y | |
31 | help | |
32 | If you say yes here, the system time (wall clock) will be stored | |
33 | in the RTC specified by RTC_HCTOSYS_DEVICE approximately every 11 | |
34 | minutes if userspace reports synchronized NTP status. | |
35 | ||
0c86edc0 | 36 | config RTC_HCTOSYS_DEVICE |
7ca1d488 | 37 | string "RTC used to set the system time" |
023f333a | 38 | depends on RTC_HCTOSYS = y || RTC_SYSTOHC = y |
0c86edc0 AZ |
39 | default "rtc0" |
40 | help | |
7ca1d488 | 41 | The RTC device that will be used to (re)initialize the system |
ae64d169 AZ |
42 | clock, usually rtc0. Initialization is done when the system |
43 | starts up, and when it resumes from a low power state. This | |
779d2089 DB |
44 | device should record time in UTC, since the kernel won't do |
45 | timezone correction. | |
7ca1d488 | 46 | |
55ff1aba DB |
47 | The driver for this RTC device must be loaded before late_initcall |
48 | functions run, so it must usually be statically linked. | |
49 | ||
7ca1d488 | 50 | This clock should be battery-backed, so that it reads the correct |
ae64d169 | 51 | time when the system boots from a power-off state. Otherwise, your |
7ca1d488 DB |
52 | system will need an external clock source (like an NTP server). |
53 | ||
54 | If the clock you specify here is not battery backed, it may still | |
55 | be useful to reinitialize system time when resuming from system | |
09b6bdb3 | 56 | sleep states. Do not specify an RTC here unless it stays powered |
7ca1d488 | 57 | during all this system's supported sleep states. |
0c86edc0 | 58 | |
9e86ecb6 DB |
59 | config RTC_DEBUG |
60 | bool "RTC debug support" | |
9e86ecb6 DB |
61 | help |
62 | Say yes here to enable debugging support in the RTC framework | |
63 | and individual RTC drivers. | |
64 | ||
0c86edc0 | 65 | comment "RTC interfaces" |
0c86edc0 | 66 | |
c5c3e192 | 67 | config RTC_INTF_SYSFS |
e40659c5 | 68 | boolean "/sys/class/rtc/rtcN (sysfs)" |
bb35fb20 | 69 | depends on SYSFS |
8dc08395 | 70 | default RTC_CLASS |
c5c3e192 | 71 | help |
9e86ecb6 DB |
72 | Say yes here if you want to use your RTCs using sysfs interfaces, |
73 | /sys/class/rtc/rtc0 through /sys/.../rtcN. | |
c5c3e192 | 74 | |
ae64d169 | 75 | If unsure, say Y. |
c5c3e192 | 76 | |
728a2947 | 77 | config RTC_INTF_PROC |
92589c98 | 78 | boolean "/proc/driver/rtc (procfs for rtcN)" |
bb35fb20 | 79 | depends on PROC_FS |
8dc08395 | 80 | default RTC_CLASS |
728a2947 | 81 | help |
92589c98 KM |
82 | Say yes here if you want to use your system clock RTC through |
83 | the proc interface, /proc/driver/rtc. | |
84 | Other RTCs will not be available through that API. | |
85 | If there is no RTC for the system clock, then the first RTC(rtc0) | |
86 | is used by default. | |
728a2947 | 87 | |
ae64d169 | 88 | If unsure, say Y. |
728a2947 | 89 | |
e824290e | 90 | config RTC_INTF_DEV |
e40659c5 | 91 | boolean "/dev/rtcN (character devices)" |
8dc08395 | 92 | default RTC_CLASS |
e824290e | 93 | help |
9e86ecb6 DB |
94 | Say yes here if you want to use your RTCs using the /dev |
95 | interfaces, which "udev" sets up as /dev/rtc0 through | |
ae64d169 | 96 | /dev/rtcN. |
e824290e | 97 | |
ae64d169 AZ |
98 | You may want to set up a symbolic link so one of these |
99 | can be accessed as /dev/rtc, which is a name | |
100 | expected by "hwclock" and some other programs. Recent | |
101 | versions of "udev" are known to set up the symlink for you. | |
102 | ||
103 | If unsure, say Y. | |
e824290e | 104 | |
6e57b1d6 JS |
105 | config RTC_INTF_DEV_UIE_EMUL |
106 | bool "RTC UIE emulation on dev interface" | |
107 | depends on RTC_INTF_DEV | |
108 | help | |
109 | Provides an emulation for RTC_UIE if the underlying rtc chip | |
110 | driver does not expose RTC_UIE ioctls. Those requests generate | |
111 | once-per-second update interrupts, used for synchronization. | |
112 | ||
113 | The emulation code will read the time from the hardware | |
114 | clock several times per second, please enable this option | |
115 | only if you know that you really need it. | |
116 | ||
09a21e56 AZ |
117 | config RTC_DRV_TEST |
118 | tristate "Test driver/device" | |
1fec7c66 AZ |
119 | help |
120 | If you say yes here you get support for the | |
09a21e56 AZ |
121 | RTC test driver. It's a software RTC which can be |
122 | used to test the RTC subsystem APIs. It gets | |
123 | the time from the system clock. | |
124 | You want this driver only if you are doing development | |
125 | on the RTC subsystem. Please read the source code | |
126 | for further details. | |
1fec7c66 AZ |
127 | |
128 | This driver can also be built as a module. If so, the module | |
09a21e56 AZ |
129 | will be called rtc-test. |
130 | ||
131 | comment "I2C RTC drivers" | |
bb35fb20 JE |
132 | depends on I2C |
133 | ||
134 | if I2C | |
1fec7c66 | 135 | |
008b3040 HZ |
136 | config RTC_DRV_88PM860X |
137 | tristate "Marvell 88PM860x" | |
6b8029fa | 138 | depends on I2C && MFD_88PM860X |
008b3040 HZ |
139 | help |
140 | If you say yes here you get support for RTC function in Marvell | |
141 | 88PM860x chips. | |
142 | ||
143 | This driver can also be built as a module. If so, the module | |
144 | will be called rtc-88pm860x. | |
145 | ||
2985c29c QZ |
146 | config RTC_DRV_88PM80X |
147 | tristate "Marvell 88PM80x" | |
6b8029fa | 148 | depends on I2C && MFD_88PM800 |
2985c29c QZ |
149 | help |
150 | If you say yes here you get support for RTC function in Marvell | |
151 | 88PM80x chips. | |
152 | ||
153 | This driver can also be built as a module. If so, the module | |
154 | will be called rtc-88pm80x. | |
155 | ||
b4506261 LD |
156 | config RTC_DRV_AS3722 |
157 | tristate "ams AS3722 RTC driver" | |
158 | depends on MFD_AS3722 | |
159 | help | |
160 | If you say yes here you get support for the RTC of ams AS3722 PMIC | |
161 | chips. | |
162 | ||
163 | This driver can also be built as a module. If so, the module | |
164 | will be called rtc-as3722. | |
165 | ||
1abb0dc9 | 166 | config RTC_DRV_DS1307 |
a2166858 | 167 | tristate "Dallas/Maxim DS1307/37/38/39/40, ST M41T00, EPSON RX-8025" |
1abb0dc9 DB |
168 | help |
169 | If you say yes here you get support for various compatible RTC | |
ae64d169 | 170 | chips (often with battery backup) connected with I2C. This driver |
1abb0dc9 | 171 | should handle DS1307, DS1337, DS1338, DS1339, DS1340, ST M41T00, |
a2166858 MF |
172 | EPSON RX-8025 and probably other chips. In some cases the RTC |
173 | must already have been initialized (by manufacturing or a | |
174 | bootloader). | |
1abb0dc9 DB |
175 | |
176 | The first seven registers on these chips hold an RTC, and other | |
177 | registers may add features such as NVRAM, a trickle charger for | |
ae64d169 | 178 | the RTC/NVRAM backup power, and alarms. NVRAM is visible in |
682d73f6 | 179 | sysfs, but other chip features may not be available. |
1abb0dc9 DB |
180 | |
181 | This driver can also be built as a module. If so, the module | |
182 | will be called rtc-ds1307. | |
183 | ||
bf4994d7 | 184 | config RTC_DRV_DS1374 |
09b6bdb3 | 185 | tristate "Dallas/Maxim DS1374" |
6b8029fa | 186 | depends on I2C |
bf4994d7 SW |
187 | help |
188 | If you say yes here you get support for Dallas Semiconductor | |
ae64d169 | 189 | DS1374 real-time clock chips. If an interrupt is associated |
bf4994d7 SW |
190 | with the device, the alarm functionality is supported. |
191 | ||
ae64d169 | 192 | This driver can also be built as a module. If so, the module |
bf4994d7 SW |
193 | will be called rtc-ds1374. |
194 | ||
920f91e5 SA |
195 | config RTC_DRV_DS1374_WDT |
196 | bool "Dallas/Maxim DS1374 watchdog timer" | |
197 | depends on RTC_DRV_DS1374 | |
198 | help | |
199 | If you say Y here you will get support for the | |
200 | watchdog timer in the Dallas Semiconductor DS1374 | |
201 | real-time clock chips. | |
202 | ||
09a21e56 AZ |
203 | config RTC_DRV_DS1672 |
204 | tristate "Dallas/Maxim DS1672" | |
9bf5b4f5 AN |
205 | help |
206 | If you say yes here you get support for the | |
09a21e56 | 207 | Dallas/Maxim DS1672 timekeeping chip. |
9bf5b4f5 AN |
208 | |
209 | This driver can also be built as a module. If so, the module | |
09a21e56 | 210 | will be called rtc-ds1672. |
9bf5b4f5 | 211 | |
c03675f0 RZ |
212 | config RTC_DRV_DS3232 |
213 | tristate "Dallas/Maxim DS3232" | |
6b8029fa | 214 | depends on I2C |
c03675f0 RZ |
215 | help |
216 | If you say yes here you get support for Dallas Semiconductor | |
f46418c5 LCB |
217 | DS3232 real-time clock chips. If an interrupt is associated |
218 | with the device, the alarm functionality is supported. | |
c03675f0 RZ |
219 | |
220 | This driver can also be built as a module. If so, the module | |
221 | will be called rtc-ds3232. | |
222 | ||
dcaf0384 HS |
223 | config RTC_DRV_HYM8563 |
224 | tristate "Haoyu Microelectronics HYM8563" | |
225 | depends on I2C && OF | |
226 | help | |
227 | Say Y to enable support for the HYM8563 I2C RTC chip. Apart | |
228 | from the usual rtc functions it provides a clock output of | |
229 | up to 32kHz. | |
230 | ||
231 | This driver can also be built as a module. If so, the module | |
232 | will be called rtc-hym8563. | |
233 | ||
38ae176e KM |
234 | config RTC_DRV_LP8788 |
235 | tristate "TI LP8788 RTC driver" | |
236 | depends on MFD_LP8788 | |
237 | help | |
238 | Say Y to enable support for the LP8788 RTC/ALARM driver. | |
239 | ||
09a21e56 | 240 | config RTC_DRV_MAX6900 |
09b6bdb3 | 241 | tristate "Maxim MAX6900" |
7e56a7dc | 242 | help |
09a21e56 AZ |
243 | If you say yes here you will get support for the |
244 | Maxim MAX6900 I2C RTC chip. | |
7e56a7dc HVR |
245 | |
246 | This driver can also be built as a module. If so, the module | |
09a21e56 | 247 | will be called rtc-max6900. |
7e56a7dc | 248 | |
94c01ab6 SW |
249 | config RTC_DRV_MAX8907 |
250 | tristate "Maxim MAX8907" | |
251 | depends on MFD_MAX8907 | |
252 | help | |
253 | If you say yes here you will get support for the | |
254 | RTC of Maxim MAX8907 PMIC. | |
255 | ||
256 | This driver can also be built as a module. If so, the module | |
257 | will be called rtc-max8907. | |
258 | ||
a39069f6 HZ |
259 | config RTC_DRV_MAX8925 |
260 | tristate "Maxim MAX8925" | |
261 | depends on MFD_MAX8925 | |
262 | help | |
263 | If you say yes here you will get support for the | |
264 | RTC of Maxim MAX8925 PMIC. | |
265 | ||
266 | This driver can also be built as a module. If so, the module | |
267 | will be called rtc-max8925. | |
268 | ||
9b16c0a4 JS |
269 | config RTC_DRV_MAX8998 |
270 | tristate "Maxim MAX8998" | |
271 | depends on MFD_MAX8998 | |
272 | help | |
273 | If you say yes here you will get support for the | |
274 | RTC of Maxim MAX8998 PMIC. | |
275 | ||
276 | This driver can also be built as a module. If so, the module | |
277 | will be called rtc-max8998. | |
278 | ||
5e0b2704 JL |
279 | config RTC_DRV_MAX8997 |
280 | tristate "Maxim MAX8997" | |
281 | depends on MFD_MAX8997 | |
282 | help | |
283 | If you say yes here you will get support for the | |
284 | RTC of Maxim MAX8997 PMIC. | |
285 | ||
286 | This driver can also be built as a module. If so, the module | |
287 | will be called rtc-max8997. | |
288 | ||
fca1dd03 JL |
289 | config RTC_DRV_MAX77686 |
290 | tristate "Maxim MAX77686" | |
291 | depends on MFD_MAX77686 | |
292 | help | |
293 | If you say yes here you will get support for the | |
294 | RTC of Maxim MAX77686 PMIC. | |
295 | ||
296 | This driver can also be built as a module. If so, the module | |
297 | will be called rtc-max77686. | |
298 | ||
3ca1e326 CZ |
299 | config RTC_DRV_RK808 |
300 | tristate "Rockchip RK808 RTC" | |
301 | depends on MFD_RK808 | |
302 | help | |
303 | If you say yes here you will get support for the | |
304 | RTC of RK808 PMIC. | |
305 | ||
306 | This driver can also be built as a module. If so, the module | |
307 | will be called rk808-rtc. | |
308 | ||
a4d4121b JMC |
309 | config RTC_DRV_MAX77802 |
310 | tristate "Maxim 77802 RTC" | |
311 | depends on MFD_MAX77686 | |
312 | help | |
313 | If you say yes here you will get support for the | |
314 | RTC of Maxim MAX77802 PMIC. | |
315 | ||
316 | This driver can also be built as a module. If so, the module | |
317 | will be called rtc-max77802. | |
318 | ||
09a21e56 | 319 | config RTC_DRV_RS5C372 |
5d4529be | 320 | tristate "Ricoh R2025S/D, RS5C372A/B, RV5C386, RV5C387A" |
edf1aaa3 AZ |
321 | help |
322 | If you say yes here you get support for the | |
5d4529be | 323 | Ricoh R2025S/D, RS5C372A, RS5C372B, RV5C386, and RV5C387A RTC chips. |
edf1aaa3 AZ |
324 | |
325 | This driver can also be built as a module. If so, the module | |
09a21e56 | 326 | will be called rtc-rs5c372. |
edf1aaa3 | 327 | |
09a21e56 | 328 | config RTC_DRV_ISL1208 |
09b6bdb3 | 329 | tristate "Intersil ISL1208" |
5ec3e4b7 AN |
330 | help |
331 | If you say yes here you get support for the | |
09b6bdb3 | 332 | Intersil ISL1208 RTC chip. |
5ec3e4b7 AN |
333 | |
334 | This driver can also be built as a module. If so, the module | |
09a21e56 | 335 | will be called rtc-isl1208. |
5ec3e4b7 | 336 | |
d6c7428f RF |
337 | config RTC_DRV_ISL12022 |
338 | tristate "Intersil ISL12022" | |
339 | help | |
340 | If you say yes here you get support for the | |
341 | Intersil ISL12022 RTC chip. | |
342 | ||
343 | This driver can also be built as a module. If so, the module | |
344 | will be called rtc-isl12022. | |
345 | ||
70e12337 AE |
346 | config RTC_DRV_ISL12057 |
347 | depends on I2C | |
348 | select REGMAP_I2C | |
349 | tristate "Intersil ISL12057" | |
350 | help | |
351 | If you say yes here you get support for the Intersil ISL12057 | |
352 | I2C RTC chip. | |
353 | ||
354 | This driver can also be built as a module. If so, the module | |
355 | will be called rtc-isl12057. | |
356 | ||
09a21e56 AZ |
357 | config RTC_DRV_X1205 |
358 | tristate "Xicor/Intersil X1205" | |
db68b189 | 359 | help |
09a21e56 AZ |
360 | If you say yes here you get support for the |
361 | Xicor/Intersil X1205 RTC chip. | |
362 | ||
363 | This driver can also be built as a module. If so, the module | |
364 | will be called rtc-x1205. | |
db68b189 | 365 | |
0101e53c LD |
366 | config RTC_DRV_PALMAS |
367 | tristate "TI Palmas RTC driver" | |
368 | depends on MFD_PALMAS | |
369 | help | |
370 | If you say yes here you get support for the RTC of TI PALMA series PMIC | |
371 | chips. | |
372 | ||
373 | This driver can also be built as a module. If so, the module | |
374 | will be called rtc-palma. | |
375 | ||
18cb6368 RC |
376 | config RTC_DRV_PCF2127 |
377 | tristate "NXP PCF2127" | |
378 | help | |
379 | If you say yes here you get support for the NXP PCF2127/29 RTC | |
380 | chips. | |
381 | ||
382 | This driver can also be built as a module. If so, the module | |
383 | will be called rtc-pcf2127. | |
384 | ||
f803f0d0 TR |
385 | config RTC_DRV_PCF8523 |
386 | tristate "NXP PCF8523" | |
387 | help | |
388 | If you say yes here you get support for the NXP PCF8523 RTC | |
389 | chips. | |
390 | ||
391 | This driver can also be built as a module. If so, the module | |
392 | will be called rtc-pcf8523. | |
393 | ||
b5a82d62 AZ |
394 | config RTC_DRV_PCF8563 |
395 | tristate "Philips PCF8563/Epson RTC8564" | |
b5a82d62 AZ |
396 | help |
397 | If you say yes here you get support for the | |
398 | Philips PCF8563 RTC chip. The Epson RTC8564 | |
399 | should work as well. | |
400 | ||
401 | This driver can also be built as a module. If so, the module | |
402 | will be called rtc-pcf8563. | |
403 | ||
796b7abb SA |
404 | config RTC_DRV_PCF85063 |
405 | tristate "nxp PCF85063" | |
406 | help | |
407 | If you say yes here you get support for the PCF85063 RTC chip | |
408 | ||
409 | This driver can also be built as a module. If so, the module | |
410 | will be called rtc-pcf85063. | |
411 | ||
9c0c5705 L |
412 | config RTC_DRV_PCF8583 |
413 | tristate "Philips PCF8583" | |
9c0c5705 | 414 | help |
bb71f99f | 415 | If you say yes here you get support for the Philips PCF8583 |
09a21e56 | 416 | RTC chip found on Acorn RiscPCs. This driver supports the |
bb71f99f | 417 | platform specific method of retrieving the current year from |
09a21e56 AZ |
418 | the RTC's SRAM. It will work on other platforms with the same |
419 | chip, but the year will probably have to be tweaked. | |
9c0c5705 L |
420 | |
421 | This driver can also be built as a module. If so, the module | |
422 | will be called rtc-pcf8583. | |
423 | ||
caaff562 | 424 | config RTC_DRV_M41T80 |
6b1a5235 | 425 | tristate "ST M41T62/65/M41T80/81/82/83/84/85/87 and compatible" |
caaff562 | 426 | help |
d3a126fc SF |
427 | If you say Y here you will get support for the ST M41T60 |
428 | and M41T80 RTC chips series. Currently, the following chips are | |
f30281f4 | 429 | supported: M41T62, M41T65, M41T80, M41T81, M41T82, M41T83, M41ST84, |
6b1a5235 | 430 | M41ST85, M41ST87, and MicroCrystal RV4162. |
caaff562 AN |
431 | |
432 | This driver can also be built as a module. If so, the module | |
433 | will be called rtc-m41t80. | |
434 | ||
617780d2 | 435 | config RTC_DRV_M41T80_WDT |
d3a126fc | 436 | bool "ST M41T65/M41T80 series RTC watchdog timer" |
617780d2 AN |
437 | depends on RTC_DRV_M41T80 |
438 | help | |
439 | If you say Y here you will get support for the | |
d3a126fc | 440 | watchdog timer in the ST M41T60 and M41T80 RTC chips series. |
617780d2 | 441 | |
1ce7c83f PZ |
442 | config RTC_DRV_BQ32K |
443 | tristate "TI BQ32000" | |
444 | help | |
445 | If you say Y here you will get support for the TI | |
446 | BQ32000 I2C RTC chip. | |
447 | ||
448 | This driver can also be built as a module. If so, the module | |
449 | will be called rtc-bq32k. | |
450 | ||
afd8d0f9 DB |
451 | config RTC_DRV_DM355EVM |
452 | tristate "TI DaVinci DM355 EVM RTC" | |
453 | depends on MFD_DM355EVM_MSP | |
454 | help | |
455 | Supports the RTC firmware in the MSP430 on the DM355 EVM. | |
456 | ||
0c4a59fe TL |
457 | config RTC_DRV_TWL92330 |
458 | boolean "TI TWL92330/Menelaus" | |
bb35fb20 | 459 | depends on MENELAUS |
0c4a59fe TL |
460 | help |
461 | If you say yes here you get support for the RTC on the | |
01dd2fbf | 462 | TWL92330 "Menelaus" power management chip, used with OMAP2 |
ae64d169 | 463 | platforms. The support is integrated with the rest of |
0c4a59fe TL |
464 | the Menelaus driver; it's not separate module. |
465 | ||
f96411ab | 466 | config RTC_DRV_TWL4030 |
a6b49ffd | 467 | tristate "TI TWL4030/TWL5030/TWL6030/TPS659x0" |
6b8029fa | 468 | depends on TWL4030_CORE |
f96411ab DB |
469 | help |
470 | If you say yes here you get support for the RTC on the | |
a6b49ffd | 471 | TWL4030/TWL5030/TWL6030 family chips, used mostly with OMAP3 platforms. |
f96411ab DB |
472 | |
473 | This driver can also be built as a module. If so, the module | |
a6b49ffd | 474 | will be called rtc-twl. |
f96411ab | 475 | |
dc59ed38 LD |
476 | config RTC_DRV_TPS6586X |
477 | tristate "TI TPS6586X RTC driver" | |
478 | depends on MFD_TPS6586X | |
479 | help | |
a895d57d | 480 | TI Power Management IC TPS6586X supports RTC functionality |
dc59ed38 LD |
481 | along with alarm. This driver supports the RTC driver for |
482 | the TPS6586X RTC module. | |
483 | ||
0e783980 VB |
484 | config RTC_DRV_TPS65910 |
485 | tristate "TI TPS65910 RTC driver" | |
486 | depends on RTC_CLASS && MFD_TPS65910 | |
487 | help | |
488 | If you say yes here you get support for the RTC on the | |
489 | TPS65910 chips. | |
490 | ||
491 | This driver can also be built as a module. If so, the module | |
492 | will be called rtc-tps65910. | |
493 | ||
36d61824 LD |
494 | config RTC_DRV_TPS80031 |
495 | tristate "TI TPS80031/TPS80032 RTC driver" | |
496 | depends on MFD_TPS80031 | |
497 | help | |
a895d57d | 498 | TI Power Management IC TPS80031 supports RTC functionality |
36d61824 LD |
499 | along with alarm. This driver supports the RTC driver for |
500 | the TPS80031 RTC module. | |
501 | ||
90829c08 VB |
502 | config RTC_DRV_RC5T583 |
503 | tristate "RICOH 5T583 RTC driver" | |
504 | depends on MFD_RC5T583 | |
505 | help | |
506 | If you say yes here you get support for the RTC on the | |
507 | RICOH 5T583 chips. | |
508 | ||
509 | This driver can also be built as a module. If so, the module | |
510 | will be called rtc-rc5t583. | |
511 | ||
c46288b0 BB |
512 | config RTC_DRV_S35390A |
513 | tristate "Seiko Instruments S-35390A" | |
d479540d | 514 | select BITREVERSE |
c46288b0 BB |
515 | help |
516 | If you say yes here you will get support for the Seiko | |
517 | Instruments S-35390A. | |
518 | ||
519 | This driver can also be built as a module. If so the module | |
520 | will be called rtc-s35390a. | |
521 | ||
c6d8f400 SL |
522 | config RTC_DRV_FM3130 |
523 | tristate "Ramtron FM3130" | |
524 | help | |
525 | If you say Y here you will get support for the | |
526 | Ramtron FM3130 RTC chips. | |
527 | Ramtron FM3130 is a chip with two separate devices inside, | |
528 | RTC clock and FRAM. This driver provides only RTC functionality. | |
529 | ||
530 | This driver can also be built as a module. If so the module | |
531 | will be called rtc-fm3130. | |
532 | ||
a7fa9851 MW |
533 | config RTC_DRV_RX8581 |
534 | tristate "Epson RX-8581" | |
535 | help | |
536 | If you say yes here you will get support for the Epson RX-8581. | |
537 | ||
538 | This driver can also be built as a module. If so the module | |
539 | will be called rtc-rx8581. | |
540 | ||
3c2b9075 WG |
541 | config RTC_DRV_RX8025 |
542 | tristate "Epson RX-8025SA/NB" | |
543 | help | |
544 | If you say yes here you get support for the Epson | |
545 | RX-8025SA/NB RTC chips. | |
546 | ||
547 | This driver can also be built as a module. If so, the module | |
548 | will be called rtc-rx8025. | |
549 | ||
ae3551f9 MR |
550 | config RTC_DRV_EM3027 |
551 | tristate "EM Microelectronic EM3027" | |
552 | help | |
553 | If you say yes here you get support for the EM | |
554 | Microelectronic EM3027 RTC chips. | |
555 | ||
556 | This driver can also be built as a module. If so, the module | |
557 | will be called rtc-em3027. | |
558 | ||
52365230 HS |
559 | config RTC_DRV_RV3029C2 |
560 | tristate "Micro Crystal RTC" | |
561 | help | |
562 | If you say yes here you get support for the Micro Crystal | |
563 | RV3029-C2 RTC chips. | |
564 | ||
565 | This driver can also be built as a module. If so, the module | |
566 | will be called rtc-rv3029c2. | |
567 | ||
5bccae6e | 568 | config RTC_DRV_S5M |
0c5deb1e | 569 | tristate "Samsung S2M/S5M series" |
5bccae6e SK |
570 | depends on MFD_SEC_CORE |
571 | help | |
572 | If you say yes here you will get support for the | |
0c5deb1e | 573 | RTC of Samsung S2MPS14 and S5M PMIC series. |
5bccae6e SK |
574 | |
575 | This driver can also be built as a module. If so, the module | |
576 | will be called rtc-s5m. | |
577 | ||
bb35fb20 JE |
578 | endif # I2C |
579 | ||
09a21e56 | 580 | comment "SPI RTC drivers" |
bb35fb20 JE |
581 | |
582 | if SPI_MASTER | |
09a21e56 | 583 | |
74d34d4b VN |
584 | config RTC_DRV_M41T93 |
585 | tristate "ST M41T93" | |
586 | help | |
587 | If you say yes here you will get support for the | |
588 | ST M41T93 SPI RTC chip. | |
589 | ||
590 | This driver can also be built as a module. If so, the module | |
591 | will be called rtc-m41t93. | |
592 | ||
8fc2c767 KH |
593 | config RTC_DRV_M41T94 |
594 | tristate "ST M41T94" | |
595 | help | |
596 | If you say yes here you will get support for the | |
597 | ST M41T94 SPI RTC chip. | |
598 | ||
599 | This driver can also be built as a module. If so, the module | |
600 | will be called rtc-m41t94. | |
601 | ||
53e84b67 DB |
602 | config RTC_DRV_DS1305 |
603 | tristate "Dallas/Maxim DS1305/DS1306" | |
604 | help | |
605 | Select this driver to get support for the Dallas/Maxim DS1305 | |
ae64d169 | 606 | and DS1306 real time clock chips. These support a trickle |
53e84b67 DB |
607 | charger, alarms, and NVRAM in addition to the clock. |
608 | ||
609 | This driver can also be built as a module. If so, the module | |
610 | will be called rtc-ds1305. | |
611 | ||
1d6316f5 | 612 | config RTC_DRV_DS1343 |
0dd449b1 | 613 | select REGMAP_SPI |
1d6316f5 RG |
614 | tristate "Dallas/Maxim DS1343/DS1344" |
615 | help | |
616 | If you say yes here you get support for the | |
617 | Dallas/Maxim DS1343 and DS1344 real time clock chips. | |
618 | Support for trickle charger, alarm is provided. | |
619 | ||
620 | This driver can also be built as a module. If so, the module | |
621 | will be called rtc-ds1343. | |
622 | ||
617b26a0 RG |
623 | config RTC_DRV_DS1347 |
624 | tristate "Dallas/Maxim DS1347" | |
625 | help | |
626 | If you say yes here you get support for the | |
627 | Dallas/Maxim DS1347 chips. | |
628 | ||
629 | This driver only supports the RTC feature, and not other chip | |
630 | features such as alarms. | |
631 | ||
632 | This driver can also be built as a module. If so, the module | |
633 | will be called rtc-ds1347. | |
634 | ||
06de1808 MJ |
635 | config RTC_DRV_DS1390 |
636 | tristate "Dallas/Maxim DS1390/93/94" | |
637 | help | |
7b9b2ef1 AZ |
638 | If you say yes here you get support for the |
639 | Dallas/Maxim DS1390/93/94 chips. | |
06de1808 MJ |
640 | |
641 | This driver only supports the RTC feature, and not other chip | |
642 | features such as alarms and trickle charging. | |
643 | ||
644 | This driver can also be built as a module. If so, the module | |
645 | will be called rtc-ds1390. | |
646 | ||
09b6bdb3 AZ |
647 | config RTC_DRV_MAX6902 |
648 | tristate "Maxim MAX6902" | |
649 | help | |
650 | If you say yes here you will get support for the | |
651 | Maxim MAX6902 SPI RTC chip. | |
652 | ||
653 | This driver can also be built as a module. If so, the module | |
654 | will be called rtc-max6902. | |
655 | ||
2805b969 MD |
656 | config RTC_DRV_R9701 |
657 | tristate "Epson RTC-9701JE" | |
658 | help | |
659 | If you say yes here you will get support for the | |
660 | Epson RTC-9701JE SPI RTC chip. | |
661 | ||
662 | This driver can also be built as a module. If so, the module | |
663 | will be called rtc-r9701. | |
664 | ||
e0ac4761 AN |
665 | config RTC_DRV_RS5C348 |
666 | tristate "Ricoh RS5C348A/B" | |
e0ac4761 AN |
667 | help |
668 | If you say yes here you get support for the | |
669 | Ricoh RS5C348A and RS5C348B RTC chips. | |
670 | ||
671 | This driver can also be built as a module. If so, the module | |
672 | will be called rtc-rs5c348. | |
673 | ||
2f9b75e0 DA |
674 | config RTC_DRV_DS3234 |
675 | tristate "Maxim/Dallas DS3234" | |
676 | help | |
677 | If you say yes here you get support for the | |
678 | Maxim/Dallas DS3234 SPI RTC chip. | |
679 | ||
680 | This driver can also be built as a module. If so, the module | |
681 | will be called rtc-ds3234. | |
682 | ||
7f3923a1 CV |
683 | config RTC_DRV_PCF2123 |
684 | tristate "NXP PCF2123" | |
685 | help | |
686 | If you say yes here you get support for the NXP PCF2123 | |
687 | RTC chip. | |
688 | ||
689 | This driver can also be built as a module. If so, the module | |
690 | will be called rtc-pcf2123. | |
691 | ||
cce2da9a TH |
692 | config RTC_DRV_RX4581 |
693 | tristate "Epson RX-4581" | |
694 | help | |
695 | If you say yes here you will get support for the Epson RX-4581. | |
696 | ||
697 | This driver can also be built as a module. If so the module | |
698 | will be called rtc-rx4581. | |
699 | ||
1fcbe42c JG |
700 | config RTC_DRV_MCP795 |
701 | tristate "Microchip MCP795" | |
702 | help | |
703 | If you say yes here you will get support for the Microchip MCP795. | |
704 | ||
705 | This driver can also be built as a module. If so the module | |
706 | will be called rtc-mcp795. | |
707 | ||
bb35fb20 JE |
708 | endif # SPI_MASTER |
709 | ||
09a21e56 | 710 | comment "Platform RTC drivers" |
09a21e56 AZ |
711 | |
712 | # this 'CMOS' RTC driver is arch dependent because <asm-generic/rtc.h> | |
713 | # requires <asm/mc146818rtc.h> defining CMOS_READ/CMOS_WRITE, and a | |
714 | # global rtc_lock ... it's not yet just another platform_device. | |
715 | ||
716 | config RTC_DRV_CMOS | |
717 | tristate "PC-style 'CMOS'" | |
41c9dbf4 | 718 | depends on X86 || ARM || M32R || PPC || MIPS || SPARC64 |
c7500900 | 719 | default y if X86 |
09a21e56 AZ |
720 | help |
721 | Say "yes" here to get direct support for the real time clock | |
722 | found in every PC or ACPI-based system, and some other boards. | |
723 | Specifically the original MC146818, compatibles like those in | |
724 | PC south bridges, the DS12887 or M48T86, some multifunction | |
725 | or LPC bus chips, and so on. | |
726 | ||
727 | Your system will need to define the platform device used by | |
ae64d169 | 728 | this driver, otherwise it won't be accessible. This means |
09a21e56 AZ |
729 | you can safely enable this driver if you don't know whether |
730 | or not your board has this kind of hardware. | |
731 | ||
732 | This driver can also be built as a module. If so, the module | |
733 | will be called rtc-cmos. | |
734 | ||
85d0b3a5 RH |
735 | config RTC_DRV_ALPHA |
736 | bool "Alpha PC-style CMOS" | |
737 | depends on ALPHA | |
738 | default y | |
739 | help | |
740 | Direct support for the real-time clock found on every Alpha | |
741 | system, specifically MC146818 compatibles. If in doubt, say Y. | |
742 | ||
0146f261 | 743 | config RTC_DRV_VRTC |
933b9463 AC |
744 | tristate "Virtual RTC for Intel MID platforms" |
745 | depends on X86_INTEL_MID | |
746 | default y if X86_INTEL_MID | |
0146f261 FT |
747 | |
748 | help | |
749 | Say "yes" here to get direct support for the real time clock | |
750 | found on Moorestown platforms. The VRTC is a emulated RTC that | |
751 | derives its clock source from a real RTC in the PMIC. The MC146818 | |
752 | style programming interface is mostly conserved, but any | |
753 | updates are done via IPC calls to the system controller FW. | |
754 | ||
537739de TB |
755 | config RTC_DRV_DS1216 |
756 | tristate "Dallas DS1216" | |
bb35fb20 | 757 | depends on SNI_RM |
537739de TB |
758 | help |
759 | If you say yes here you get support for the Dallas DS1216 RTC chips. | |
760 | ||
5f119f29 TB |
761 | config RTC_DRV_DS1286 |
762 | tristate "Dallas DS1286" | |
706b632d | 763 | depends on HAS_IOMEM |
5f119f29 TB |
764 | help |
765 | If you say yes here you get support for the Dallas DS1286 RTC chips. | |
766 | ||
739d340d PM |
767 | config RTC_DRV_DS1302 |
768 | tristate "Dallas DS1302" | |
769 | depends on SH_SECUREEDGE5410 | |
770 | help | |
771 | If you say yes here you get support for the Dallas DS1302 RTC chips. | |
772 | ||
8f26795a AS |
773 | config RTC_DRV_DS1511 |
774 | tristate "Dallas DS1511" | |
706b632d | 775 | depends on HAS_IOMEM |
8f26795a AS |
776 | help |
777 | If you say yes here you get support for the | |
778 | Dallas DS1511 timekeeping/watchdog chip. | |
779 | ||
780 | This driver can also be built as a module. If so, the module | |
781 | will be called rtc-ds1511. | |
782 | ||
09a21e56 | 783 | config RTC_DRV_DS1553 |
09b6bdb3 | 784 | tristate "Maxim/Dallas DS1553" |
706b632d | 785 | depends on HAS_IOMEM |
7520b94d AZ |
786 | help |
787 | If you say yes here you get support for the | |
09b6bdb3 | 788 | Maxim/Dallas DS1553 timekeeping chip. |
7520b94d AZ |
789 | |
790 | This driver can also be built as a module. If so, the module | |
09a21e56 AZ |
791 | will be called rtc-ds1553. |
792 | ||
09b6bdb3 AZ |
793 | config RTC_DRV_DS1742 |
794 | tristate "Maxim/Dallas DS1742/1743" | |
706b632d | 795 | depends on HAS_IOMEM |
02964115 TH |
796 | help |
797 | If you say yes here you get support for the | |
09b6bdb3 | 798 | Maxim/Dallas DS1742/1743 timekeeping chip. |
02964115 TH |
799 | |
800 | This driver can also be built as a module. If so, the module | |
09b6bdb3 | 801 | will be called rtc-ds1742. |
02964115 | 802 | |
ad0200f7 JD |
803 | config RTC_DRV_DS2404 |
804 | tristate "Maxim/Dallas DS2404" | |
805 | help | |
806 | If you say yes here you get support for the | |
807 | Dallas DS2404 RTC chip. | |
808 | ||
809 | This driver can also be built as a module. If so, the module | |
810 | will be called rtc-ds2404. | |
811 | ||
fef931ff AJ |
812 | config RTC_DRV_DA9052 |
813 | tristate "Dialog DA9052/DA9053 RTC" | |
814 | depends on PMIC_DA9052 | |
815 | help | |
816 | Say y here to support the RTC driver for Dialog Semiconductor | |
817 | DA9052-BC and DA9053-AA/Bx PMICs. | |
818 | ||
6920d996 AJ |
819 | config RTC_DRV_DA9055 |
820 | tristate "Dialog Semiconductor DA9055 RTC" | |
821 | depends on MFD_DA9055 | |
822 | help | |
823 | If you say yes here you will get support for the | |
824 | RTC of the Dialog DA9055 PMIC. | |
825 | ||
826 | This driver can also be built as a module. If so, the module | |
827 | will be called rtc-da9055 | |
828 | ||
c2a57550 OST |
829 | config RTC_DRV_DA9063 |
830 | tristate "Dialog Semiconductor DA9063 RTC" | |
831 | depends on MFD_DA9063 | |
832 | help | |
833 | If you say yes here you will get support for the RTC subsystem | |
834 | of the Dialog Semiconductor DA9063. | |
835 | ||
836 | This driver can also be built as a module. If so, the module | |
837 | will be called "rtc-da9063". | |
838 | ||
5e3fd9e5 | 839 | config RTC_DRV_EFI |
840 | tristate "EFI RTC" | |
7efe6659 | 841 | depends on EFI && !X86 |
5e3fd9e5 | 842 | help |
843 | If you say yes here you will get support for the EFI | |
844 | Real Time Clock. | |
845 | ||
846 | This driver can also be built as a module. If so, the module | |
847 | will be called rtc-efi. | |
848 | ||
09b6bdb3 AZ |
849 | config RTC_DRV_STK17TA8 |
850 | tristate "Simtek STK17TA8" | |
706b632d | 851 | depends on HAS_IOMEM |
09a21e56 AZ |
852 | help |
853 | If you say yes here you get support for the | |
09b6bdb3 | 854 | Simtek STK17TA8 timekeeping chip. |
09a21e56 AZ |
855 | |
856 | This driver can also be built as a module. If so, the module | |
09b6bdb3 | 857 | will be called rtc-stk17ta8. |
09a21e56 AZ |
858 | |
859 | config RTC_DRV_M48T86 | |
860 | tristate "ST M48T86/Dallas DS12887" | |
09a21e56 AZ |
861 | help |
862 | If you say Y here you will get support for the | |
863 | ST M48T86 and Dallas DS12887 RTC chips. | |
864 | ||
865 | This driver can also be built as a module. If so, the module | |
866 | will be called rtc-m48t86. | |
867 | ||
d1dbd82e TB |
868 | config RTC_DRV_M48T35 |
869 | tristate "ST M48T35" | |
706b632d | 870 | depends on HAS_IOMEM |
d1dbd82e TB |
871 | help |
872 | If you say Y here you will get support for the | |
873 | ST M48T35 RTC chip. | |
874 | ||
875 | This driver can also be built as a module, if so, the module | |
876 | will be called "rtc-m48t35". | |
877 | ||
2e774c7c | 878 | config RTC_DRV_M48T59 |
94fe7424 | 879 | tristate "ST M48T59/M48T08/M48T02" |
706b632d | 880 | depends on HAS_IOMEM |
2e774c7c MZ |
881 | help |
882 | If you say Y here you will get support for the | |
94fe7424 KH |
883 | ST M48T59 RTC chip and compatible ST M48T08 and M48T02. |
884 | ||
885 | These chips are usually found in Sun SPARC and UltraSPARC | |
886 | workstations. | |
2e774c7c MZ |
887 | |
888 | This driver can also be built as a module, if so, the module | |
889 | will be called "rtc-m48t59". | |
890 | ||
4f9b9bba GU |
891 | config RTC_DRV_MSM6242 |
892 | tristate "Oki MSM6242" | |
706b632d | 893 | depends on HAS_IOMEM |
4f9b9bba GU |
894 | help |
895 | If you say yes here you get support for the Oki MSM6242 | |
896 | timekeeping chip. It is used in some Amiga models (e.g. A2000). | |
897 | ||
898 | This driver can also be built as a module. If so, the module | |
899 | will be called rtc-msm6242. | |
900 | ||
cca4c231 DM |
901 | config RTC_DRV_BQ4802 |
902 | tristate "TI BQ4802" | |
706b632d | 903 | depends on HAS_IOMEM |
cca4c231 DM |
904 | help |
905 | If you say Y here you will get support for the TI | |
906 | BQ4802 RTC chip. | |
907 | ||
908 | This driver can also be built as a module. If so, the module | |
909 | will be called rtc-bq4802. | |
910 | ||
4f672ce2 GU |
911 | config RTC_DRV_RP5C01 |
912 | tristate "Ricoh RP5C01" | |
706b632d | 913 | depends on HAS_IOMEM |
4f672ce2 GU |
914 | help |
915 | If you say yes here you get support for the Ricoh RP5C01 | |
916 | timekeeping chip. It is used in some Amiga models (e.g. A3000 | |
917 | and A4000). | |
918 | ||
919 | This driver can also be built as a module. If so, the module | |
920 | will be called rtc-rp5c01. | |
921 | ||
09a21e56 AZ |
922 | config RTC_DRV_V3020 |
923 | tristate "EM Microelectronic V3020" | |
09a21e56 AZ |
924 | help |
925 | If you say yes here you will get support for the | |
926 | EM Microelectronic v3020 RTC chip. | |
927 | ||
928 | This driver can also be built as a module. If so, the module | |
929 | will be called rtc-v3020. | |
930 | ||
35c86bf6 MB |
931 | config RTC_DRV_WM831X |
932 | tristate "Wolfson Microelectronics WM831x RTC" | |
933 | depends on MFD_WM831X | |
934 | help | |
935 | If you say yes here you will get support for the RTC subsystem | |
936 | of the Wolfson Microelectronics WM831X series PMICs. | |
937 | ||
938 | This driver can also be built as a module. If so, the module | |
939 | will be called "rtc-wm831x". | |
940 | ||
077eaf5b MB |
941 | config RTC_DRV_WM8350 |
942 | tristate "Wolfson Microelectronics WM8350 RTC" | |
943 | depends on MFD_WM8350 | |
944 | help | |
945 | If you say yes here you will get support for the RTC subsystem | |
946 | of the Wolfson Microelectronics WM8350. | |
947 | ||
948 | This driver can also be built as a module. If so, the module | |
949 | will be called "rtc-wm8350". | |
950 | ||
0942a71e RK |
951 | config RTC_DRV_SPEAR |
952 | tristate "SPEAR ST RTC" | |
953 | depends on PLAT_SPEAR | |
954 | default y | |
955 | help | |
956 | If you say Y here you will get support for the RTC found on | |
957 | spear | |
958 | ||
eae854b2 BR |
959 | config RTC_DRV_PCF50633 |
960 | depends on MFD_PCF50633 | |
961 | tristate "NXP PCF50633 RTC" | |
962 | help | |
963 | If you say yes here you get support for the RTC subsystem of the | |
964 | NXP PCF50633 used in embedded systems. | |
965 | ||
bd207cfb LW |
966 | config RTC_DRV_AB3100 |
967 | tristate "ST-Ericsson AB3100 RTC" | |
968 | depends on AB3100_CORE | |
969 | default y if AB3100_CORE | |
970 | help | |
971 | Select this to enable the ST-Ericsson AB3100 Mixed Signal IC RTC | |
972 | support. This chip contains a battery- and capacitor-backed RTC. | |
973 | ||
0af62f4d VS |
974 | config RTC_DRV_AB8500 |
975 | tristate "ST-Ericsson AB8500 RTC" | |
976 | depends on AB8500_CORE | |
651fb480 | 977 | select RTC_INTF_DEV |
dc43d4a2 | 978 | select RTC_INTF_DEV_UIE_EMUL |
0af62f4d VS |
979 | help |
980 | Select this to enable the ST-Ericsson AB8500 power management IC RTC | |
981 | support. This chip contains a battery- and capacitor-backed RTC. | |
982 | ||
afd49a7e WZ |
983 | config RTC_DRV_NUC900 |
984 | tristate "NUC910/NUC920 RTC driver" | |
6b8029fa | 985 | depends on ARCH_W90X900 |
afd49a7e WZ |
986 | help |
987 | If you say yes here you get support for the RTC subsystem of the | |
988 | NUC910/NUC920 used in embedded systems. | |
bd207cfb | 989 | |
16b1d26e NG |
990 | config RTC_DRV_OPAL |
991 | tristate "IBM OPAL RTC driver" | |
992 | depends on PPC_POWERNV | |
993 | default y | |
994 | help | |
995 | If you say yes here you get support for the PowerNV platform RTC | |
996 | driver based on OPAL interfaces. | |
997 | ||
998 | This driver can also be built as a module. If so, the module | |
999 | will be called rtc-opal. | |
1000 | ||
09a21e56 | 1001 | comment "on-CPU RTC drivers" |
09a21e56 | 1002 | |
8ecf6c54 MA |
1003 | config RTC_DRV_DAVINCI |
1004 | tristate "TI DaVinci RTC" | |
1005 | depends on ARCH_DAVINCI_DM365 | |
1006 | help | |
1007 | If you say yes here you get support for the RTC on the | |
1008 | DaVinci platforms (DM365). | |
1009 | ||
1010 | This driver can also be built as a module. If so, the module | |
1011 | will be called rtc-davinci. | |
1012 | ||
b224b9ac FE |
1013 | config RTC_DRV_IMXDI |
1014 | tristate "Freescale IMX DryIce Real Time Clock" | |
ef216ad0 | 1015 | depends on ARCH_MXC |
b224b9ac FE |
1016 | help |
1017 | Support for Freescale IMX DryIce RTC | |
1018 | ||
1019 | This driver can also be built as a module, if so, the module | |
1020 | will be called "rtc-imxdi". | |
1021 | ||
09a21e56 AZ |
1022 | config RTC_DRV_OMAP |
1023 | tristate "TI OMAP1" | |
427af9a6 | 1024 | depends on ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730 || ARCH_DAVINCI_DA8XX || SOC_AM33XX |
09a21e56 | 1025 | help |
427af9a6 AM |
1026 | Say "yes" here to support the on chip real time clock |
1027 | present on TI OMAP1, AM33xx and DA8xx/OMAP-L13x. | |
1028 | ||
1029 | This driver can also be built as a module, if so, module | |
1030 | will be called rtc-omap. | |
7520b94d | 1031 | |
16f4efe7 AD |
1032 | config HAVE_S3C_RTC |
1033 | bool | |
1034 | help | |
1035 | This will include RTC support for Samsung SoCs. If | |
1036 | you want to include RTC support for any machine, kindly | |
1037 | select this in the respective mach-XXXX/Kconfig file. | |
1038 | ||
1add6781 BD |
1039 | config RTC_DRV_S3C |
1040 | tristate "Samsung S3C series SoC RTC" | |
b130d5c2 | 1041 | depends on ARCH_S3C64XX || HAVE_S3C_RTC |
1add6781 BD |
1042 | help |
1043 | RTC (Realtime Clock) driver for the clock inbuilt into the | |
1044 | Samsung S3C24XX series of SoCs. This can provide periodic | |
1045 | interrupt rates from 1Hz to 64Hz for user programs, and | |
1046 | wakeup from Alarm. | |
1047 | ||
1048 | The driver currently supports the common features on all the | |
1049 | S3C24XX range, such as the S3C2410, S3C2412, S3C2413, S3C2440 | |
1050 | and S3C2442. | |
1051 | ||
1052 | This driver can also be build as a module. If so, the module | |
1053 | will be called rtc-s3c. | |
1054 | ||
fd507e2f AZ |
1055 | config RTC_DRV_EP93XX |
1056 | tristate "Cirrus Logic EP93XX" | |
bb35fb20 | 1057 | depends on ARCH_EP93XX |
fd507e2f AZ |
1058 | help |
1059 | If you say yes here you get support for the | |
1060 | RTC embedded in the Cirrus Logic EP93XX processors. | |
1061 | ||
1062 | This driver can also be built as a module. If so, the module | |
1063 | will be called rtc-ep93xx. | |
1064 | ||
e842f1c8 | 1065 | config RTC_DRV_SA1100 |
3888c090 HZ |
1066 | tristate "SA11x0/PXA2xx/PXA910" |
1067 | depends on ARCH_SA1100 || ARCH_PXA || ARCH_MMP | |
e842f1c8 RP |
1068 | help |
1069 | If you say Y here you will get access to the real time clock | |
1070 | built into your SA11x0 or PXA2xx CPU. | |
1071 | ||
1072 | To compile this driver as a module, choose M here: the | |
1073 | module will be called rtc-sa1100. | |
fd507e2f | 1074 | |
317a6104 PM |
1075 | config RTC_DRV_SH |
1076 | tristate "SuperH On-Chip RTC" | |
6b8029fa | 1077 | depends on SUPERH && HAVE_CLK |
317a6104 PM |
1078 | help |
1079 | Say Y here to enable support for the on-chip RTC found in | |
1080 | most SuperH processors. | |
1081 | ||
1082 | To compile this driver as a module, choose M here: the | |
1083 | module will be called rtc-sh. | |
1084 | ||
8417eb7a | 1085 | config RTC_DRV_VR41XX |
3e16f6af | 1086 | tristate "NEC VR41XX" |
bb35fb20 | 1087 | depends on CPU_VR41XX |
3e16f6af AZ |
1088 | help |
1089 | If you say Y here you will get access to the real time clock | |
1090 | built into your NEC VR41XX CPU. | |
1091 | ||
1092 | To compile this driver as a module, choose M here: the | |
1093 | module will be called rtc-vr41xx. | |
8417eb7a | 1094 | |
a190901c RK |
1095 | config RTC_DRV_PL030 |
1096 | tristate "ARM AMBA PL030 RTC" | |
1097 | depends on ARM_AMBA | |
1098 | help | |
1099 | If you say Y here you will get access to ARM AMBA | |
1100 | PrimeCell PL030 RTC found on certain ARM SOCs. | |
1101 | ||
1102 | To compile this driver as a module, choose M here: the | |
1103 | module will be called rtc-pl030. | |
1104 | ||
8ae6e163 DS |
1105 | config RTC_DRV_PL031 |
1106 | tristate "ARM AMBA PL031 RTC" | |
bb35fb20 | 1107 | depends on ARM_AMBA |
8ae6e163 DS |
1108 | help |
1109 | If you say Y here you will get access to ARM AMBA | |
09a21e56 | 1110 | PrimeCell PL031 RTC found on certain ARM SOCs. |
8ae6e163 DS |
1111 | |
1112 | To compile this driver as a module, choose M here: the | |
1113 | module will be called rtc-pl031. | |
1114 | ||
fa04e78b HCE |
1115 | config RTC_DRV_AT32AP700X |
1116 | tristate "AT32AP700X series RTC" | |
bb35fb20 | 1117 | depends on PLATFORM_AT32AP |
fa04e78b HCE |
1118 | help |
1119 | Driver for the internal RTC (Realtime Clock) on Atmel AVR32 | |
1120 | AT32AP700x family processors. | |
1121 | ||
7fc39f6d | 1122 | config RTC_DRV_AT91RM9200 |
24cecc1b | 1123 | tristate "AT91RM9200 or some AT91SAM9 RTC" |
938f970e | 1124 | depends on ARCH_AT91 |
4cdf854f DB |
1125 | help |
1126 | Driver for the internal RTC (Realtime Clock) module found on | |
24cecc1b | 1127 | Atmel AT91RM9200's and some AT91SAM9 chips. On AT91SAM9 chips |
4cdf854f DB |
1128 | this is powered by the backup power supply. |
1129 | ||
1130 | config RTC_DRV_AT91SAM9 | |
3969eb48 | 1131 | tristate "AT91SAM9 RTT as RTC" |
ee72f18b | 1132 | depends on ARCH_AT91 |
43e112bb | 1133 | select MFD_SYSCON |
4cdf854f | 1134 | help |
3969eb48 BB |
1135 | Some AT91SAM9 SoCs provide an RTT (Real Time Timer) block which |
1136 | can be used as an RTC thanks to the backup power supply (e.g. a | |
1137 | small coin cell battery) which keeps this block and the GPBR | |
1138 | (General Purpose Backup Registers) block powered when the device | |
1139 | is shutdown. | |
1140 | Some AT91SAM9 SoCs provide a real RTC block, on those ones you'd | |
1141 | probably want to use the real RTC block instead of the "RTT as an | |
1142 | RTC" driver. | |
4cdf854f DB |
1143 | |
1144 | config RTC_DRV_AT91SAM9_RTT | |
1145 | int | |
1146 | range 0 1 | |
1147 | default 0 | |
4cdf854f DB |
1148 | depends on RTC_DRV_AT91SAM9 |
1149 | help | |
3969eb48 BB |
1150 | This option is only relevant for legacy board support and |
1151 | won't be used when booting a DT board. | |
1152 | ||
ae64d169 AZ |
1153 | More than one RTT module is available. You can choose which |
1154 | one will be used as an RTC. The default of zero is normally | |
4cdf854f DB |
1155 | OK to use, though some systems use that for non-RTC purposes. |
1156 | ||
1157 | config RTC_DRV_AT91SAM9_GPBR | |
1158 | int | |
9373090d | 1159 | range 0 3 |
4cdf854f DB |
1160 | default 0 |
1161 | prompt "Backup Register Number" | |
1162 | depends on RTC_DRV_AT91SAM9 | |
1163 | help | |
3969eb48 BB |
1164 | This option is only relevant for legacy board support and |
1165 | won't be used when booting a DT board. | |
1166 | ||
4cdf854f | 1167 | The RTC driver needs to use one of the General Purpose Backup |
ae64d169 AZ |
1168 | Registers (GPBRs) as well as the RTT. You can choose which one |
1169 | will be used. The default of zero is normally OK to use, but | |
4cdf854f | 1170 | on some systems other software needs to use that register. |
788b1fc6 | 1171 | |
45fd8a0c ML |
1172 | config RTC_DRV_AU1XXX |
1173 | tristate "Au1xxx Counter0 RTC support" | |
42a4f17d | 1174 | depends on MIPS_ALCHEMY |
45fd8a0c ML |
1175 | help |
1176 | This is a driver for the Au1xxx on-chip Counter0 (Time-Of-Year | |
1177 | counter) to be used as a RTC. | |
1178 | ||
1179 | This driver can also be built as a module. If so, the module | |
1180 | will be called rtc-au1xxx. | |
1181 | ||
8cc75c9a WB |
1182 | config RTC_DRV_BFIN |
1183 | tristate "Blackfin On-Chip RTC" | |
7f604599 | 1184 | depends on BLACKFIN && !BF561 |
8cc75c9a WB |
1185 | help |
1186 | If you say yes here you will get support for the | |
1187 | Blackfin On-Chip Real Time Clock. | |
1188 | ||
1189 | This driver can also be built as a module. If so, the module | |
1190 | will be called rtc-bfin. | |
1191 | ||
e9f2bd81 NI |
1192 | config RTC_DRV_RS5C313 |
1193 | tristate "Ricoh RS5C313" | |
bb35fb20 | 1194 | depends on SH_LANDISK |
e9f2bd81 NI |
1195 | help |
1196 | If you say yes here you get support for the Ricoh RS5C313 RTC chips. | |
1197 | ||
3afe6d04 GU |
1198 | config RTC_DRV_GENERIC |
1199 | tristate "Generic RTC support" | |
1200 | # Please consider writing a new RTC driver instead of using the generic | |
1201 | # RTC abstraction | |
47c8a08b | 1202 | depends on PARISC || M68K || PPC || SUPERH32 |
9eb16864 | 1203 | help |
3afe6d04 GU |
1204 | Say Y or M here to enable RTC support on systems using the generic |
1205 | RTC abstraction. If you do not know what you are doing, you should | |
9eb16864 KM |
1206 | just say Y. |
1207 | ||
dc944368 RJ |
1208 | config RTC_DRV_PXA |
1209 | tristate "PXA27x/PXA3xx" | |
1210 | depends on ARCH_PXA | |
1211 | help | |
1212 | If you say Y here you will get access to the real time clock | |
1213 | built into your PXA27x or PXA3xx CPU. | |
1214 | ||
1215 | This RTC driver uses PXA RTC registers available since pxa27x | |
1216 | series (RDxR, RYxR) instead of legacy RCNR, RTAR. | |
1217 | ||
f77fbdf9 AC |
1218 | config RTC_DRV_VT8500 |
1219 | tristate "VIA/WonderMedia 85xx SoC RTC" | |
1220 | depends on ARCH_VT8500 | |
1221 | help | |
1222 | If you say Y here you will get access to the real time clock | |
1223 | built into your VIA VT8500 SoC or its relatives. | |
1224 | ||
dc944368 | 1225 | |
7a138ede DM |
1226 | config RTC_DRV_SUN4V |
1227 | bool "SUN4V Hypervisor RTC" | |
1228 | depends on SPARC64 | |
1229 | help | |
1230 | If you say Y here you will get support for the Hypervisor | |
1231 | based RTC on SUN4V systems. | |
1232 | ||
9765d2d9 CYT |
1233 | config RTC_DRV_SUN6I |
1234 | tristate "Allwinner A31 RTC" | |
1235 | depends on MACH_SUN6I || MACH_SUN8I | |
1236 | help | |
1237 | If you say Y here you will get support for the RTC found on | |
1238 | Allwinner A31. | |
1239 | ||
594c6fb9 CC |
1240 | config RTC_DRV_SUNXI |
1241 | tristate "Allwinner sun4i/sun7i RTC" | |
64a1925c | 1242 | depends on MACH_SUN4I || MACH_SUN7I |
594c6fb9 CC |
1243 | help |
1244 | If you say Y here you will get support for the RTC found on | |
1245 | Allwinner A10/A20. | |
1246 | ||
de2cf332 DM |
1247 | config RTC_DRV_STARFIRE |
1248 | bool "Starfire RTC" | |
1249 | depends on SPARC64 | |
1250 | help | |
1251 | If you say Y here you will get support for the RTC found on | |
1252 | Starfire systems. | |
1253 | ||
0e149233 AN |
1254 | config RTC_DRV_TX4939 |
1255 | tristate "TX4939 SoC" | |
1256 | depends on SOC_TX4939 | |
1257 | help | |
1258 | Driver for the internal RTC (Realtime Clock) module found on | |
1259 | Toshiba TX4939 SoC. | |
1260 | ||
defb4514 SB |
1261 | config RTC_DRV_MV |
1262 | tristate "Marvell SoC RTC" | |
ace2c020 | 1263 | depends on ARCH_DOVE || ARCH_MVEBU |
defb4514 SB |
1264 | help |
1265 | If you say yes here you will get support for the in-chip RTC | |
1266 | that can be found in some of Marvell's SoC devices, such as | |
1267 | the Kirkwood 88F6281 and 88F6192. | |
1268 | ||
1269 | This driver can also be built as a module. If so, the module | |
1270 | will be called rtc-mv. | |
1271 | ||
0b5f037a GU |
1272 | config RTC_DRV_PS3 |
1273 | tristate "PS3 RTC" | |
1274 | depends on PPC_PS3 | |
1275 | help | |
1276 | If you say yes here you will get support for the RTC on PS3. | |
1277 | ||
1278 | This driver can also be built as a module. If so, the module | |
1279 | will be called rtc-ps3. | |
1280 | ||
aa958f57 LW |
1281 | config RTC_DRV_COH901331 |
1282 | tristate "ST-Ericsson COH 901 331 RTC" | |
1283 | depends on ARCH_U300 | |
1284 | help | |
1285 | If you say Y here you will get access to ST-Ericsson | |
1286 | COH 901 331 RTC clock found in some ST-Ericsson Mobile | |
1287 | Platforms. | |
1288 | ||
1289 | This driver can also be built as a module. If so, the module | |
1290 | will be called "rtc-coh901331". | |
1291 | ||
1292 | ||
df17f631 | 1293 | config RTC_DRV_STMP |
46b21218 WS |
1294 | tristate "Freescale STMP3xxx/i.MX23/i.MX28 RTC" |
1295 | depends on ARCH_MXS | |
df17f631 | 1296 | help |
1297 | If you say yes here you will get support for the onboard | |
46b21218 | 1298 | STMP3xxx/i.MX23/i.MX28 RTC. |
df17f631 | 1299 | |
1300 | This driver can also be built as a module. If so, the module | |
1301 | will be called rtc-stmp3xxx. | |
1302 | ||
d3c7a3f7 DR |
1303 | config RTC_DRV_PCAP |
1304 | tristate "PCAP RTC" | |
1305 | depends on EZX_PCAP | |
1306 | help | |
1307 | If you say Y here you will get support for the RTC found on | |
1308 | the PCAP2 ASIC used on some Motorola phones. | |
1309 | ||
1c97872b UKK |
1310 | config RTC_DRV_MC13XXX |
1311 | depends on MFD_MC13XXX | |
1312 | tristate "Freescale MC13xxx RTC" | |
43299f28 | 1313 | help |
1c97872b UKK |
1314 | This enables support for the RTCs found on Freescale's PMICs |
1315 | MC13783 and MC13892. | |
43299f28 | 1316 | |
50aae724 AG |
1317 | config RTC_DRV_MPC5121 |
1318 | tristate "Freescale MPC5121 built-in RTC" | |
955dbea3 | 1319 | depends on PPC_MPC512x || PPC_MPC52xx |
50aae724 AG |
1320 | help |
1321 | If you say yes here you will get support for the | |
955dbea3 | 1322 | built-in RTC on MPC5121 or on MPC5200. |
50aae724 AG |
1323 | |
1324 | This driver can also be built as a module. If so, the module | |
1325 | will be called rtc-mpc5121. | |
1326 | ||
3bf0eea8 LPC |
1327 | config RTC_DRV_JZ4740 |
1328 | tristate "Ingenic JZ4740 SoC" | |
3bf0eea8 LPC |
1329 | depends on MACH_JZ4740 |
1330 | help | |
1331 | If you say yes here you get support for the Ingenic JZ4740 SoC RTC | |
1332 | controller. | |
1333 | ||
1334 | This driver can also be buillt as a module. If so, the module | |
1335 | will be called rtc-jz4740. | |
1336 | ||
9aa449be KW |
1337 | config RTC_DRV_LPC32XX |
1338 | depends on ARCH_LPC32XX | |
1339 | tristate "NXP LPC32XX RTC" | |
1340 | help | |
1341 | This enables support for the NXP RTC in the LPC32XX | |
1342 | ||
1343 | This driver can also be buillt as a module. If so, the module | |
1344 | will be called rtc-lpc32xx. | |
1345 | ||
9a9a54ad AG |
1346 | config RTC_DRV_PM8XXX |
1347 | tristate "Qualcomm PMIC8XXX RTC" | |
c8d523a4 | 1348 | depends on MFD_PM8XXX || MFD_SPMI_PMIC |
9a9a54ad AG |
1349 | help |
1350 | If you say yes here you get support for the | |
1351 | Qualcomm PMIC8XXX RTC. | |
1352 | ||
1353 | To compile this driver as a module, choose M here: the | |
1354 | module will be called rtc-pm8xxx. | |
1355 | ||
ff859ba6 AC |
1356 | config RTC_DRV_TEGRA |
1357 | tristate "NVIDIA Tegra Internal RTC driver" | |
6b8029fa | 1358 | depends on ARCH_TEGRA |
ff859ba6 AC |
1359 | help |
1360 | If you say yes here you get support for the | |
1361 | Tegra 200 series internal RTC module. | |
1362 | ||
1363 | This drive can also be built as a module. If so, the module | |
1364 | will be called rtc-tegra. | |
1365 | ||
dd196a2b CM |
1366 | config RTC_DRV_TILE |
1367 | tristate "Tilera hypervisor RTC support" | |
1368 | depends on TILE | |
1369 | help | |
1370 | Enable support for the Linux driver side of the Tilera | |
1371 | hypervisor's real-time clock interface. | |
1372 | ||
2809e80b GX |
1373 | config RTC_DRV_PUV3 |
1374 | tristate "PKUnity v3 RTC support" | |
1375 | depends on ARCH_PUV3 | |
1376 | help | |
1377 | This enables support for the RTC in the PKUnity-v3 SoCs. | |
1378 | ||
1379 | This drive can also be built as a module. If so, the module | |
1380 | will be called rtc-puv3. | |
1381 | ||
b4f0b880 | 1382 | config RTC_DRV_LOONGSON1 |
1383 | tristate "loongson1 RTC support" | |
1384 | depends on MACH_LOONGSON1 | |
1385 | help | |
1386 | This is a driver for the loongson1 on-chip Counter0 (Time-Of-Year | |
1387 | counter) to be used as a RTC. | |
1388 | ||
1389 | This driver can also be built as a module. If so, the module | |
1390 | will be called rtc-ls1x. | |
1391 | ||
79811595 | 1392 | config RTC_DRV_MXC |
b224b9ac FE |
1393 | tristate "Freescale MXC Real Time Clock" |
1394 | depends on ARCH_MXC | |
b224b9ac FE |
1395 | help |
1396 | If you say yes here you get support for the Freescale MXC | |
1397 | RTC module. | |
1398 | ||
1399 | This driver can also be built as a module, if so, the module | |
1400 | will be called "rtc-mxc". | |
1401 | ||
179a502f SG |
1402 | config RTC_DRV_SNVS |
1403 | tristate "Freescale SNVS RTC support" | |
1404 | depends on HAS_IOMEM | |
1405 | depends on OF | |
1406 | help | |
1407 | If you say yes here you get support for the Freescale SNVS | |
1408 | Low Power (LP) RTC module. | |
1409 | ||
1410 | This driver can also be built as a module, if so, the module | |
1411 | will be called "rtc-snvs". | |
1412 | ||
e88b815e XD |
1413 | config RTC_DRV_SIRFSOC |
1414 | tristate "SiRFSOC RTC" | |
1415 | depends on ARCH_SIRF | |
1416 | help | |
1417 | Say "yes" here to support the real time clock on SiRF SOC chips. | |
1418 | This driver can also be built as a module called rtc-sirfsoc. | |
1419 | ||
453b4c6d JJ |
1420 | config RTC_DRV_MOXART |
1421 | tristate "MOXA ART RTC" | |
441fb768 | 1422 | depends on ARCH_MOXART || COMPILE_TEST |
453b4c6d JJ |
1423 | help |
1424 | If you say yes here you get support for the MOXA ART | |
1425 | RTC module. | |
1426 | ||
1427 | This driver can also be built as a module. If so, the module | |
1428 | will be called rtc-moxart | |
1429 | ||
f12d8695 LH |
1430 | config RTC_DRV_XGENE |
1431 | tristate "APM X-Gene RTC" | |
706b632d | 1432 | depends on HAS_IOMEM |
f12d8695 LH |
1433 | help |
1434 | If you say yes here you get support for the APM X-Gene SoC real time | |
1435 | clock. | |
1436 | ||
1437 | This driver can also be built as a module, if so, the module | |
1438 | will be called "rtc-xgene". | |
1439 | ||
62e00cb9 AH |
1440 | comment "HID Sensor RTC drivers" |
1441 | ||
1442 | config RTC_DRV_HID_SENSOR_TIME | |
1443 | tristate "HID Sensor Time" | |
1444 | depends on USB_HID | |
1445 | select IIO | |
1446 | select HID_SENSOR_HUB | |
1447 | select HID_SENSOR_IIO_COMMON | |
1448 | help | |
1449 | Say yes here to build support for the HID Sensors of type Time. | |
1450 | This drivers makes such sensors available as RTCs. | |
1451 | ||
1452 | If this driver is compiled as a module, it will be named | |
1453 | rtc-hid-sensor-time. | |
1454 | ||
1455 | ||
bb35fb20 | 1456 | endif # RTC_CLASS |