Commit | Line | Data |
---|---|---|
d87a6d95 | 1 | /* |
1da177e4 LT |
2 | * su.c: Small serial driver for keyboard/mouse interface on sparc32/PCI |
3 | * | |
4 | * Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be) | |
5 | * Copyright (C) 1998-1999 Pete Zaitcev (zaitcev@yahoo.com) | |
6 | * | |
7 | * This is mainly a variation of 8250.c, credits go to authors mentioned | |
8 | * therein. In fact this driver should be merged into the generic 8250.c | |
9 | * infrastructure perhaps using a 8250_sparc.c module. | |
10 | * | |
11 | * Fixed to use tty_get_baud_rate(). | |
12 | * Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12 | |
13 | * | |
14 | * Converted to new 2.5.x UART layer. | |
9efc3715 | 15 | * David S. Miller (davem@davemloft.net), 2002-Jul-29 |
1da177e4 LT |
16 | */ |
17 | ||
1da177e4 LT |
18 | #include <linux/module.h> |
19 | #include <linux/kernel.h> | |
1da177e4 LT |
20 | #include <linux/spinlock.h> |
21 | #include <linux/errno.h> | |
22 | #include <linux/tty.h> | |
23 | #include <linux/tty_flip.h> | |
24 | #include <linux/major.h> | |
25 | #include <linux/string.h> | |
26 | #include <linux/ptrace.h> | |
27 | #include <linux/ioport.h> | |
28 | #include <linux/circ_buf.h> | |
29 | #include <linux/serial.h> | |
30 | #include <linux/sysrq.h> | |
31 | #include <linux/console.h> | |
5a0e3ad6 | 32 | #include <linux/slab.h> |
1da177e4 LT |
33 | #ifdef CONFIG_SERIO |
34 | #include <linux/serio.h> | |
35 | #endif | |
36 | #include <linux/serial_reg.h> | |
37 | #include <linux/init.h> | |
38 | #include <linux/delay.h> | |
c6ed413d | 39 | #include <linux/of_device.h> |
1da177e4 LT |
40 | |
41 | #include <asm/io.h> | |
42 | #include <asm/irq.h> | |
1708d242 | 43 | #include <asm/prom.h> |
1da177e4 LT |
44 | |
45 | #if defined(CONFIG_SERIAL_SUNSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) | |
46 | #define SUPPORT_SYSRQ | |
47 | #endif | |
48 | ||
49 | #include <linux/serial_core.h> | |
50 | ||
51 | #include "suncore.h" | |
52 | ||
53 | /* We are on a NS PC87303 clocked with 24.0 MHz, which results | |
54 | * in a UART clock of 1.8462 MHz. | |
55 | */ | |
56 | #define SU_BASE_BAUD (1846200 / 16) | |
57 | ||
58 | enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT }; | |
59 | static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" }; | |
60 | ||
61 | /* | |
62 | * Here we define the default xmit fifo size used for each type of UART. | |
63 | */ | |
64 | static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = { | |
65 | { "unknown", 1, 0 }, | |
66 | { "8250", 1, 0 }, | |
67 | { "16450", 1, 0 }, | |
68 | { "16550", 1, 0 }, | |
69 | { "16550A", 16, UART_CLEAR_FIFO | UART_USE_FIFO }, | |
70 | { "Cirrus", 1, 0 }, | |
71 | { "ST16650", 1, UART_CLEAR_FIFO | UART_STARTECH }, | |
72 | { "ST16650V2", 32, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH }, | |
73 | { "TI16750", 64, UART_CLEAR_FIFO | UART_USE_FIFO }, | |
74 | { "Startech", 1, 0 }, | |
75 | { "16C950/954", 128, UART_CLEAR_FIFO | UART_USE_FIFO }, | |
76 | { "ST16654", 64, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH }, | |
77 | { "XR16850", 128, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH }, | |
78 | { "RSA", 2048, UART_CLEAR_FIFO | UART_USE_FIFO } | |
79 | }; | |
80 | ||
81 | struct uart_sunsu_port { | |
82 | struct uart_port port; | |
83 | unsigned char acr; | |
84 | unsigned char ier; | |
85 | unsigned short rev; | |
86 | unsigned char lcr; | |
87 | unsigned int lsr_break_flag; | |
88 | unsigned int cflag; | |
89 | ||
90 | /* Probing information. */ | |
91 | enum su_type su_type; | |
92 | unsigned int type_probed; /* XXX Stupid */ | |
1708d242 | 93 | unsigned long reg_size; |
1da177e4 LT |
94 | |
95 | #ifdef CONFIG_SERIO | |
1708d242 | 96 | struct serio serio; |
1da177e4 LT |
97 | int serio_open; |
98 | #endif | |
99 | }; | |
100 | ||
41c28ff1 | 101 | static unsigned int serial_in(struct uart_sunsu_port *up, int offset) |
1da177e4 LT |
102 | { |
103 | offset <<= up->port.regshift; | |
104 | ||
105 | switch (up->port.iotype) { | |
9b4a1617 | 106 | case UPIO_HUB6: |
1da177e4 LT |
107 | outb(up->port.hub6 - 1 + offset, up->port.iobase); |
108 | return inb(up->port.iobase + 1); | |
109 | ||
9b4a1617 | 110 | case UPIO_MEM: |
1da177e4 LT |
111 | return readb(up->port.membase + offset); |
112 | ||
113 | default: | |
114 | return inb(up->port.iobase + offset); | |
115 | } | |
116 | } | |
117 | ||
41c28ff1 | 118 | static void serial_out(struct uart_sunsu_port *up, int offset, int value) |
1da177e4 LT |
119 | { |
120 | #ifndef CONFIG_SPARC64 | |
121 | /* | |
122 | * MrCoffee has weird schematics: IRQ4 & P10(?) pins of SuperIO are | |
123 | * connected with a gate then go to SlavIO. When IRQ4 goes tristated | |
124 | * gate outputs a logical one. Since we use level triggered interrupts | |
125 | * we have lockup and watchdog reset. We cannot mask IRQ because | |
126 | * keyboard shares IRQ with us (Word has it as Bob Smelik's design). | |
127 | * This problem is similar to what Alpha people suffer, see serial.c. | |
128 | */ | |
129 | if (offset == UART_MCR) | |
130 | value |= UART_MCR_OUT2; | |
131 | #endif | |
132 | offset <<= up->port.regshift; | |
133 | ||
134 | switch (up->port.iotype) { | |
9b4a1617 | 135 | case UPIO_HUB6: |
1da177e4 LT |
136 | outb(up->port.hub6 - 1 + offset, up->port.iobase); |
137 | outb(value, up->port.iobase + 1); | |
138 | break; | |
139 | ||
9b4a1617 | 140 | case UPIO_MEM: |
1da177e4 LT |
141 | writeb(value, up->port.membase + offset); |
142 | break; | |
143 | ||
144 | default: | |
145 | outb(value, up->port.iobase + offset); | |
146 | } | |
147 | } | |
148 | ||
149 | /* | |
150 | * We used to support using pause I/O for certain machines. We | |
151 | * haven't supported this for a while, but just in case it's badly | |
152 | * needed for certain old 386 machines, I've left these #define's | |
153 | * in.... | |
154 | */ | |
155 | #define serial_inp(up, offset) serial_in(up, offset) | |
156 | #define serial_outp(up, offset, value) serial_out(up, offset, value) | |
157 | ||
158 | ||
159 | /* | |
160 | * For the 16C950 | |
161 | */ | |
162 | static void serial_icr_write(struct uart_sunsu_port *up, int offset, int value) | |
163 | { | |
164 | serial_out(up, UART_SCR, offset); | |
165 | serial_out(up, UART_ICR, value); | |
166 | } | |
167 | ||
168 | #if 0 /* Unused currently */ | |
169 | static unsigned int serial_icr_read(struct uart_sunsu_port *up, int offset) | |
170 | { | |
171 | unsigned int value; | |
172 | ||
173 | serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD); | |
174 | serial_out(up, UART_SCR, offset); | |
175 | value = serial_in(up, UART_ICR); | |
176 | serial_icr_write(up, UART_ACR, up->acr); | |
177 | ||
178 | return value; | |
179 | } | |
180 | #endif | |
181 | ||
182 | #ifdef CONFIG_SERIAL_8250_RSA | |
183 | /* | |
184 | * Attempts to turn on the RSA FIFO. Returns zero on failure. | |
185 | * We set the port uart clock rate if we succeed. | |
186 | */ | |
187 | static int __enable_rsa(struct uart_sunsu_port *up) | |
188 | { | |
189 | unsigned char mode; | |
190 | int result; | |
191 | ||
192 | mode = serial_inp(up, UART_RSA_MSR); | |
193 | result = mode & UART_RSA_MSR_FIFO; | |
194 | ||
195 | if (!result) { | |
196 | serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO); | |
197 | mode = serial_inp(up, UART_RSA_MSR); | |
198 | result = mode & UART_RSA_MSR_FIFO; | |
199 | } | |
200 | ||
201 | if (result) | |
202 | up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16; | |
203 | ||
204 | return result; | |
205 | } | |
206 | ||
207 | static void enable_rsa(struct uart_sunsu_port *up) | |
208 | { | |
209 | if (up->port.type == PORT_RSA) { | |
210 | if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) { | |
211 | spin_lock_irq(&up->port.lock); | |
212 | __enable_rsa(up); | |
213 | spin_unlock_irq(&up->port.lock); | |
214 | } | |
215 | if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) | |
216 | serial_outp(up, UART_RSA_FRR, 0); | |
217 | } | |
218 | } | |
219 | ||
220 | /* | |
221 | * Attempts to turn off the RSA FIFO. Returns zero on failure. | |
222 | * It is unknown why interrupts were disabled in here. However, | |
223 | * the caller is expected to preserve this behaviour by grabbing | |
224 | * the spinlock before calling this function. | |
225 | */ | |
226 | static void disable_rsa(struct uart_sunsu_port *up) | |
227 | { | |
228 | unsigned char mode; | |
229 | int result; | |
230 | ||
231 | if (up->port.type == PORT_RSA && | |
232 | up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) { | |
233 | spin_lock_irq(&up->port.lock); | |
234 | ||
235 | mode = serial_inp(up, UART_RSA_MSR); | |
236 | result = !(mode & UART_RSA_MSR_FIFO); | |
237 | ||
238 | if (!result) { | |
239 | serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO); | |
240 | mode = serial_inp(up, UART_RSA_MSR); | |
241 | result = !(mode & UART_RSA_MSR_FIFO); | |
242 | } | |
243 | ||
244 | if (result) | |
245 | up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16; | |
246 | spin_unlock_irq(&up->port.lock); | |
247 | } | |
248 | } | |
249 | #endif /* CONFIG_SERIAL_8250_RSA */ | |
250 | ||
b129a8cc RK |
251 | static inline void __stop_tx(struct uart_sunsu_port *p) |
252 | { | |
253 | if (p->ier & UART_IER_THRI) { | |
254 | p->ier &= ~UART_IER_THRI; | |
255 | serial_out(p, UART_IER, p->ier); | |
256 | } | |
257 | } | |
258 | ||
259 | static void sunsu_stop_tx(struct uart_port *port) | |
1da177e4 LT |
260 | { |
261 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
262 | ||
b129a8cc RK |
263 | __stop_tx(up); |
264 | ||
3d9c9948 AV |
265 | /* |
266 | * We really want to stop the transmitter from sending. | |
267 | */ | |
268 | if (up->port.type == PORT_16C950) { | |
1da177e4 LT |
269 | up->acr |= UART_ACR_TXDIS; |
270 | serial_icr_write(up, UART_ACR, up->acr); | |
271 | } | |
272 | } | |
273 | ||
b129a8cc | 274 | static void sunsu_start_tx(struct uart_port *port) |
1da177e4 LT |
275 | { |
276 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
277 | ||
278 | if (!(up->ier & UART_IER_THRI)) { | |
279 | up->ier |= UART_IER_THRI; | |
280 | serial_out(up, UART_IER, up->ier); | |
281 | } | |
3d9c9948 | 282 | |
1da177e4 | 283 | /* |
3d9c9948 | 284 | * Re-enable the transmitter if we disabled it. |
1da177e4 | 285 | */ |
3d9c9948 | 286 | if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) { |
1da177e4 LT |
287 | up->acr &= ~UART_ACR_TXDIS; |
288 | serial_icr_write(up, UART_ACR, up->acr); | |
289 | } | |
290 | } | |
291 | ||
292 | static void sunsu_stop_rx(struct uart_port *port) | |
293 | { | |
294 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
1da177e4 | 295 | |
1da177e4 LT |
296 | up->ier &= ~UART_IER_RLSI; |
297 | up->port.read_status_mask &= ~UART_LSR_DR; | |
298 | serial_out(up, UART_IER, up->ier); | |
1da177e4 LT |
299 | } |
300 | ||
301 | static void sunsu_enable_ms(struct uart_port *port) | |
302 | { | |
303 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
304 | unsigned long flags; | |
305 | ||
306 | spin_lock_irqsave(&up->port.lock, flags); | |
307 | up->ier |= UART_IER_MSI; | |
308 | serial_out(up, UART_IER, up->ier); | |
309 | spin_unlock_irqrestore(&up->port.lock, flags); | |
310 | } | |
311 | ||
41c28ff1 | 312 | static struct tty_struct * |
7d12e780 | 313 | receive_chars(struct uart_sunsu_port *up, unsigned char *status) |
1da177e4 | 314 | { |
ebd2c8f6 | 315 | struct tty_struct *tty = up->port.state->port.tty; |
33f0f88f | 316 | unsigned char ch, flag; |
1da177e4 LT |
317 | int max_count = 256; |
318 | int saw_console_brk = 0; | |
319 | ||
320 | do { | |
1da177e4 | 321 | ch = serial_inp(up, UART_RX); |
33f0f88f | 322 | flag = TTY_NORMAL; |
1da177e4 LT |
323 | up->port.icount.rx++; |
324 | ||
325 | if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE | | |
326 | UART_LSR_FE | UART_LSR_OE))) { | |
327 | /* | |
328 | * For statistics only | |
329 | */ | |
330 | if (*status & UART_LSR_BI) { | |
331 | *status &= ~(UART_LSR_FE | UART_LSR_PE); | |
332 | up->port.icount.brk++; | |
333 | if (up->port.cons != NULL && | |
334 | up->port.line == up->port.cons->index) | |
335 | saw_console_brk = 1; | |
336 | /* | |
337 | * We do the SysRQ and SAK checking | |
338 | * here because otherwise the break | |
339 | * may get masked by ignore_status_mask | |
340 | * or read_status_mask. | |
341 | */ | |
342 | if (uart_handle_break(&up->port)) | |
343 | goto ignore_char; | |
344 | } else if (*status & UART_LSR_PE) | |
345 | up->port.icount.parity++; | |
346 | else if (*status & UART_LSR_FE) | |
347 | up->port.icount.frame++; | |
348 | if (*status & UART_LSR_OE) | |
349 | up->port.icount.overrun++; | |
350 | ||
351 | /* | |
352 | * Mask off conditions which should be ingored. | |
353 | */ | |
354 | *status &= up->port.read_status_mask; | |
355 | ||
356 | if (up->port.cons != NULL && | |
357 | up->port.line == up->port.cons->index) { | |
358 | /* Recover the break flag from console xmit */ | |
359 | *status |= up->lsr_break_flag; | |
360 | up->lsr_break_flag = 0; | |
361 | } | |
362 | ||
363 | if (*status & UART_LSR_BI) { | |
33f0f88f | 364 | flag = TTY_BREAK; |
1da177e4 | 365 | } else if (*status & UART_LSR_PE) |
33f0f88f | 366 | flag = TTY_PARITY; |
1da177e4 | 367 | else if (*status & UART_LSR_FE) |
33f0f88f | 368 | flag = TTY_FRAME; |
1da177e4 | 369 | } |
7d12e780 | 370 | if (uart_handle_sysrq_char(&up->port, ch)) |
1da177e4 | 371 | goto ignore_char; |
33f0f88f AC |
372 | if ((*status & up->port.ignore_status_mask) == 0) |
373 | tty_insert_flip_char(tty, ch, flag); | |
374 | if (*status & UART_LSR_OE) | |
1da177e4 LT |
375 | /* |
376 | * Overrun is special, since it's reported | |
377 | * immediately, and doesn't affect the current | |
378 | * character. | |
379 | */ | |
33f0f88f | 380 | tty_insert_flip_char(tty, 0, TTY_OVERRUN); |
1da177e4 LT |
381 | ignore_char: |
382 | *status = serial_inp(up, UART_LSR); | |
383 | } while ((*status & UART_LSR_DR) && (max_count-- > 0)); | |
384 | ||
385 | if (saw_console_brk) | |
386 | sun_do_break(); | |
387 | ||
388 | return tty; | |
389 | } | |
390 | ||
41c28ff1 | 391 | static void transmit_chars(struct uart_sunsu_port *up) |
1da177e4 | 392 | { |
ebd2c8f6 | 393 | struct circ_buf *xmit = &up->port.state->xmit; |
1da177e4 LT |
394 | int count; |
395 | ||
396 | if (up->port.x_char) { | |
397 | serial_outp(up, UART_TX, up->port.x_char); | |
398 | up->port.icount.tx++; | |
399 | up->port.x_char = 0; | |
400 | return; | |
401 | } | |
b129a8cc RK |
402 | if (uart_tx_stopped(&up->port)) { |
403 | sunsu_stop_tx(&up->port); | |
404 | return; | |
405 | } | |
406 | if (uart_circ_empty(xmit)) { | |
407 | __stop_tx(up); | |
1da177e4 LT |
408 | return; |
409 | } | |
410 | ||
411 | count = up->port.fifosize; | |
412 | do { | |
413 | serial_out(up, UART_TX, xmit->buf[xmit->tail]); | |
414 | xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); | |
415 | up->port.icount.tx++; | |
416 | if (uart_circ_empty(xmit)) | |
417 | break; | |
418 | } while (--count > 0); | |
419 | ||
420 | if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) | |
421 | uart_write_wakeup(&up->port); | |
422 | ||
423 | if (uart_circ_empty(xmit)) | |
b129a8cc | 424 | __stop_tx(up); |
1da177e4 LT |
425 | } |
426 | ||
41c28ff1 | 427 | static void check_modem_status(struct uart_sunsu_port *up) |
1da177e4 LT |
428 | { |
429 | int status; | |
430 | ||
431 | status = serial_in(up, UART_MSR); | |
432 | ||
433 | if ((status & UART_MSR_ANY_DELTA) == 0) | |
434 | return; | |
435 | ||
436 | if (status & UART_MSR_TERI) | |
437 | up->port.icount.rng++; | |
438 | if (status & UART_MSR_DDSR) | |
439 | up->port.icount.dsr++; | |
440 | if (status & UART_MSR_DDCD) | |
441 | uart_handle_dcd_change(&up->port, status & UART_MSR_DCD); | |
442 | if (status & UART_MSR_DCTS) | |
443 | uart_handle_cts_change(&up->port, status & UART_MSR_CTS); | |
444 | ||
bdc04e31 | 445 | wake_up_interruptible(&up->port.state->port.delta_msr_wait); |
1da177e4 LT |
446 | } |
447 | ||
7d12e780 | 448 | static irqreturn_t sunsu_serial_interrupt(int irq, void *dev_id) |
1da177e4 LT |
449 | { |
450 | struct uart_sunsu_port *up = dev_id; | |
451 | unsigned long flags; | |
452 | unsigned char status; | |
453 | ||
454 | spin_lock_irqsave(&up->port.lock, flags); | |
455 | ||
456 | do { | |
457 | struct tty_struct *tty; | |
458 | ||
459 | status = serial_inp(up, UART_LSR); | |
460 | tty = NULL; | |
461 | if (status & UART_LSR_DR) | |
7d12e780 | 462 | tty = receive_chars(up, &status); |
1da177e4 LT |
463 | check_modem_status(up); |
464 | if (status & UART_LSR_THRE) | |
465 | transmit_chars(up); | |
466 | ||
467 | spin_unlock_irqrestore(&up->port.lock, flags); | |
468 | ||
469 | if (tty) | |
470 | tty_flip_buffer_push(tty); | |
471 | ||
472 | spin_lock_irqsave(&up->port.lock, flags); | |
473 | ||
474 | } while (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)); | |
475 | ||
476 | spin_unlock_irqrestore(&up->port.lock, flags); | |
477 | ||
478 | return IRQ_HANDLED; | |
479 | } | |
480 | ||
481 | /* Separate interrupt handling path for keyboard/mouse ports. */ | |
482 | ||
483 | static void | |
484 | sunsu_change_speed(struct uart_port *port, unsigned int cflag, | |
485 | unsigned int iflag, unsigned int quot); | |
486 | ||
487 | static void sunsu_change_mouse_baud(struct uart_sunsu_port *up) | |
488 | { | |
489 | unsigned int cur_cflag = up->cflag; | |
490 | int quot, new_baud; | |
491 | ||
492 | up->cflag &= ~CBAUD; | |
493 | up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud); | |
494 | ||
495 | quot = up->port.uartclk / (16 * new_baud); | |
496 | ||
1da177e4 | 497 | sunsu_change_speed(&up->port, up->cflag, 0, quot); |
1da177e4 LT |
498 | } |
499 | ||
7d12e780 | 500 | static void receive_kbd_ms_chars(struct uart_sunsu_port *up, int is_break) |
1da177e4 LT |
501 | { |
502 | do { | |
503 | unsigned char ch = serial_inp(up, UART_RX); | |
504 | ||
505 | /* Stop-A is handled by drivers/char/keyboard.c now. */ | |
506 | if (up->su_type == SU_PORT_KBD) { | |
507 | #ifdef CONFIG_SERIO | |
7d12e780 | 508 | serio_interrupt(&up->serio, ch, 0); |
1da177e4 LT |
509 | #endif |
510 | } else if (up->su_type == SU_PORT_MS) { | |
511 | int ret = suncore_mouse_baud_detection(ch, is_break); | |
512 | ||
513 | switch (ret) { | |
514 | case 2: | |
515 | sunsu_change_mouse_baud(up); | |
516 | /* fallthru */ | |
517 | case 1: | |
518 | break; | |
519 | ||
520 | case 0: | |
521 | #ifdef CONFIG_SERIO | |
7d12e780 | 522 | serio_interrupt(&up->serio, ch, 0); |
1da177e4 LT |
523 | #endif |
524 | break; | |
525 | }; | |
526 | } | |
527 | } while (serial_in(up, UART_LSR) & UART_LSR_DR); | |
528 | } | |
529 | ||
7d12e780 | 530 | static irqreturn_t sunsu_kbd_ms_interrupt(int irq, void *dev_id) |
1da177e4 LT |
531 | { |
532 | struct uart_sunsu_port *up = dev_id; | |
533 | ||
534 | if (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)) { | |
535 | unsigned char status = serial_inp(up, UART_LSR); | |
536 | ||
537 | if ((status & UART_LSR_DR) || (status & UART_LSR_BI)) | |
7d12e780 | 538 | receive_kbd_ms_chars(up, (status & UART_LSR_BI) != 0); |
1da177e4 LT |
539 | } |
540 | ||
541 | return IRQ_HANDLED; | |
542 | } | |
543 | ||
544 | static unsigned int sunsu_tx_empty(struct uart_port *port) | |
545 | { | |
546 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
547 | unsigned long flags; | |
548 | unsigned int ret; | |
549 | ||
550 | spin_lock_irqsave(&up->port.lock, flags); | |
551 | ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0; | |
552 | spin_unlock_irqrestore(&up->port.lock, flags); | |
553 | ||
554 | return ret; | |
555 | } | |
556 | ||
557 | static unsigned int sunsu_get_mctrl(struct uart_port *port) | |
558 | { | |
559 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
1da177e4 LT |
560 | unsigned char status; |
561 | unsigned int ret; | |
562 | ||
1da177e4 | 563 | status = serial_in(up, UART_MSR); |
1da177e4 LT |
564 | |
565 | ret = 0; | |
566 | if (status & UART_MSR_DCD) | |
567 | ret |= TIOCM_CAR; | |
568 | if (status & UART_MSR_RI) | |
569 | ret |= TIOCM_RNG; | |
570 | if (status & UART_MSR_DSR) | |
571 | ret |= TIOCM_DSR; | |
572 | if (status & UART_MSR_CTS) | |
573 | ret |= TIOCM_CTS; | |
574 | return ret; | |
575 | } | |
576 | ||
577 | static void sunsu_set_mctrl(struct uart_port *port, unsigned int mctrl) | |
578 | { | |
579 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
580 | unsigned char mcr = 0; | |
581 | ||
582 | if (mctrl & TIOCM_RTS) | |
583 | mcr |= UART_MCR_RTS; | |
584 | if (mctrl & TIOCM_DTR) | |
585 | mcr |= UART_MCR_DTR; | |
586 | if (mctrl & TIOCM_OUT1) | |
587 | mcr |= UART_MCR_OUT1; | |
588 | if (mctrl & TIOCM_OUT2) | |
589 | mcr |= UART_MCR_OUT2; | |
590 | if (mctrl & TIOCM_LOOP) | |
591 | mcr |= UART_MCR_LOOP; | |
592 | ||
593 | serial_out(up, UART_MCR, mcr); | |
594 | } | |
595 | ||
596 | static void sunsu_break_ctl(struct uart_port *port, int break_state) | |
597 | { | |
598 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
599 | unsigned long flags; | |
600 | ||
601 | spin_lock_irqsave(&up->port.lock, flags); | |
602 | if (break_state == -1) | |
603 | up->lcr |= UART_LCR_SBC; | |
604 | else | |
605 | up->lcr &= ~UART_LCR_SBC; | |
606 | serial_out(up, UART_LCR, up->lcr); | |
607 | spin_unlock_irqrestore(&up->port.lock, flags); | |
608 | } | |
609 | ||
610 | static int sunsu_startup(struct uart_port *port) | |
611 | { | |
612 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
613 | unsigned long flags; | |
614 | int retval; | |
615 | ||
616 | if (up->port.type == PORT_16C950) { | |
617 | /* Wake up and initialize UART */ | |
618 | up->acr = 0; | |
619 | serial_outp(up, UART_LCR, 0xBF); | |
620 | serial_outp(up, UART_EFR, UART_EFR_ECB); | |
621 | serial_outp(up, UART_IER, 0); | |
622 | serial_outp(up, UART_LCR, 0); | |
623 | serial_icr_write(up, UART_CSR, 0); /* Reset the UART */ | |
624 | serial_outp(up, UART_LCR, 0xBF); | |
625 | serial_outp(up, UART_EFR, UART_EFR_ECB); | |
626 | serial_outp(up, UART_LCR, 0); | |
627 | } | |
628 | ||
629 | #ifdef CONFIG_SERIAL_8250_RSA | |
630 | /* | |
631 | * If this is an RSA port, see if we can kick it up to the | |
632 | * higher speed clock. | |
633 | */ | |
634 | enable_rsa(up); | |
635 | #endif | |
636 | ||
637 | /* | |
638 | * Clear the FIFO buffers and disable them. | |
7f927fcc | 639 | * (they will be reenabled in set_termios()) |
1da177e4 LT |
640 | */ |
641 | if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) { | |
642 | serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); | |
643 | serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | | |
644 | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); | |
645 | serial_outp(up, UART_FCR, 0); | |
646 | } | |
647 | ||
648 | /* | |
649 | * Clear the interrupt registers. | |
650 | */ | |
651 | (void) serial_inp(up, UART_LSR); | |
652 | (void) serial_inp(up, UART_RX); | |
653 | (void) serial_inp(up, UART_IIR); | |
654 | (void) serial_inp(up, UART_MSR); | |
655 | ||
656 | /* | |
657 | * At this point, there's no way the LSR could still be 0xff; | |
658 | * if it is, then bail out, because there's likely no UART | |
659 | * here. | |
660 | */ | |
ce8337cb | 661 | if (!(up->port.flags & UPF_BUGGY_UART) && |
1da177e4 LT |
662 | (serial_inp(up, UART_LSR) == 0xff)) { |
663 | printk("ttyS%d: LSR safety check engaged!\n", up->port.line); | |
664 | return -ENODEV; | |
665 | } | |
666 | ||
667 | if (up->su_type != SU_PORT_PORT) { | |
668 | retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt, | |
40663cc7 | 669 | IRQF_SHARED, su_typev[up->su_type], up); |
1da177e4 LT |
670 | } else { |
671 | retval = request_irq(up->port.irq, sunsu_serial_interrupt, | |
40663cc7 | 672 | IRQF_SHARED, su_typev[up->su_type], up); |
1da177e4 LT |
673 | } |
674 | if (retval) { | |
675 | printk("su: Cannot register IRQ %d\n", up->port.irq); | |
676 | return retval; | |
677 | } | |
678 | ||
679 | /* | |
680 | * Now, initialize the UART | |
681 | */ | |
682 | serial_outp(up, UART_LCR, UART_LCR_WLEN8); | |
683 | ||
684 | spin_lock_irqsave(&up->port.lock, flags); | |
685 | ||
686 | up->port.mctrl |= TIOCM_OUT2; | |
687 | ||
688 | sunsu_set_mctrl(&up->port, up->port.mctrl); | |
689 | spin_unlock_irqrestore(&up->port.lock, flags); | |
690 | ||
691 | /* | |
692 | * Finally, enable interrupts. Note: Modem status interrupts | |
693 | * are set via set_termios(), which will be occurring imminently | |
694 | * anyway, so we don't enable them here. | |
695 | */ | |
696 | up->ier = UART_IER_RLSI | UART_IER_RDI; | |
697 | serial_outp(up, UART_IER, up->ier); | |
698 | ||
ce8337cb | 699 | if (up->port.flags & UPF_FOURPORT) { |
1da177e4 LT |
700 | unsigned int icp; |
701 | /* | |
702 | * Enable interrupts on the AST Fourport board | |
703 | */ | |
704 | icp = (up->port.iobase & 0xfe0) | 0x01f; | |
705 | outb_p(0x80, icp); | |
706 | (void) inb_p(icp); | |
707 | } | |
708 | ||
709 | /* | |
710 | * And clear the interrupt registers again for luck. | |
711 | */ | |
712 | (void) serial_inp(up, UART_LSR); | |
713 | (void) serial_inp(up, UART_RX); | |
714 | (void) serial_inp(up, UART_IIR); | |
715 | (void) serial_inp(up, UART_MSR); | |
716 | ||
717 | return 0; | |
718 | } | |
719 | ||
720 | static void sunsu_shutdown(struct uart_port *port) | |
721 | { | |
722 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
723 | unsigned long flags; | |
724 | ||
725 | /* | |
726 | * Disable interrupts from this port | |
727 | */ | |
728 | up->ier = 0; | |
729 | serial_outp(up, UART_IER, 0); | |
730 | ||
731 | spin_lock_irqsave(&up->port.lock, flags); | |
ce8337cb | 732 | if (up->port.flags & UPF_FOURPORT) { |
1da177e4 LT |
733 | /* reset interrupts on the AST Fourport board */ |
734 | inb((up->port.iobase & 0xfe0) | 0x1f); | |
735 | up->port.mctrl |= TIOCM_OUT1; | |
736 | } else | |
737 | up->port.mctrl &= ~TIOCM_OUT2; | |
738 | ||
739 | sunsu_set_mctrl(&up->port, up->port.mctrl); | |
740 | spin_unlock_irqrestore(&up->port.lock, flags); | |
741 | ||
742 | /* | |
743 | * Disable break condition and FIFOs | |
744 | */ | |
745 | serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC); | |
746 | serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | | |
747 | UART_FCR_CLEAR_RCVR | | |
748 | UART_FCR_CLEAR_XMIT); | |
749 | serial_outp(up, UART_FCR, 0); | |
750 | ||
751 | #ifdef CONFIG_SERIAL_8250_RSA | |
752 | /* | |
753 | * Reset the RSA board back to 115kbps compat mode. | |
754 | */ | |
755 | disable_rsa(up); | |
756 | #endif | |
757 | ||
758 | /* | |
759 | * Read data port to reset things. | |
760 | */ | |
761 | (void) serial_in(up, UART_RX); | |
762 | ||
763 | free_irq(up->port.irq, up); | |
764 | } | |
765 | ||
766 | static void | |
767 | sunsu_change_speed(struct uart_port *port, unsigned int cflag, | |
768 | unsigned int iflag, unsigned int quot) | |
769 | { | |
770 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
771 | unsigned char cval, fcr = 0; | |
772 | unsigned long flags; | |
773 | ||
774 | switch (cflag & CSIZE) { | |
775 | case CS5: | |
776 | cval = 0x00; | |
777 | break; | |
778 | case CS6: | |
779 | cval = 0x01; | |
780 | break; | |
781 | case CS7: | |
782 | cval = 0x02; | |
783 | break; | |
784 | default: | |
785 | case CS8: | |
786 | cval = 0x03; | |
787 | break; | |
788 | } | |
789 | ||
790 | if (cflag & CSTOPB) | |
791 | cval |= 0x04; | |
792 | if (cflag & PARENB) | |
793 | cval |= UART_LCR_PARITY; | |
794 | if (!(cflag & PARODD)) | |
795 | cval |= UART_LCR_EPAR; | |
796 | #ifdef CMSPAR | |
797 | if (cflag & CMSPAR) | |
798 | cval |= UART_LCR_SPAR; | |
799 | #endif | |
800 | ||
801 | /* | |
802 | * Work around a bug in the Oxford Semiconductor 952 rev B | |
803 | * chip which causes it to seriously miscalculate baud rates | |
804 | * when DLL is 0. | |
805 | */ | |
806 | if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 && | |
807 | up->rev == 0x5201) | |
808 | quot ++; | |
809 | ||
810 | if (uart_config[up->port.type].flags & UART_USE_FIFO) { | |
811 | if ((up->port.uartclk / quot) < (2400 * 16)) | |
812 | fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1; | |
813 | #ifdef CONFIG_SERIAL_8250_RSA | |
814 | else if (up->port.type == PORT_RSA) | |
815 | fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_14; | |
816 | #endif | |
817 | else | |
818 | fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8; | |
819 | } | |
820 | if (up->port.type == PORT_16750) | |
821 | fcr |= UART_FCR7_64BYTE; | |
822 | ||
823 | /* | |
824 | * Ok, we're now changing the port state. Do it with | |
825 | * interrupts disabled. | |
826 | */ | |
827 | spin_lock_irqsave(&up->port.lock, flags); | |
828 | ||
829 | /* | |
830 | * Update the per-port timeout. | |
831 | */ | |
832 | uart_update_timeout(port, cflag, (port->uartclk / (16 * quot))); | |
833 | ||
834 | up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; | |
835 | if (iflag & INPCK) | |
836 | up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE; | |
837 | if (iflag & (BRKINT | PARMRK)) | |
838 | up->port.read_status_mask |= UART_LSR_BI; | |
839 | ||
840 | /* | |
841 | * Characteres to ignore | |
842 | */ | |
843 | up->port.ignore_status_mask = 0; | |
844 | if (iflag & IGNPAR) | |
845 | up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; | |
846 | if (iflag & IGNBRK) { | |
847 | up->port.ignore_status_mask |= UART_LSR_BI; | |
848 | /* | |
849 | * If we're ignoring parity and break indicators, | |
850 | * ignore overruns too (for real raw support). | |
851 | */ | |
852 | if (iflag & IGNPAR) | |
853 | up->port.ignore_status_mask |= UART_LSR_OE; | |
854 | } | |
855 | ||
856 | /* | |
857 | * ignore all characters if CREAD is not set | |
858 | */ | |
859 | if ((cflag & CREAD) == 0) | |
860 | up->port.ignore_status_mask |= UART_LSR_DR; | |
861 | ||
862 | /* | |
863 | * CTS flow control flag and modem status interrupts | |
864 | */ | |
865 | up->ier &= ~UART_IER_MSI; | |
866 | if (UART_ENABLE_MS(&up->port, cflag)) | |
867 | up->ier |= UART_IER_MSI; | |
868 | ||
869 | serial_out(up, UART_IER, up->ier); | |
870 | ||
871 | if (uart_config[up->port.type].flags & UART_STARTECH) { | |
872 | serial_outp(up, UART_LCR, 0xBF); | |
873 | serial_outp(up, UART_EFR, cflag & CRTSCTS ? UART_EFR_CTS :0); | |
874 | } | |
875 | serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */ | |
876 | serial_outp(up, UART_DLL, quot & 0xff); /* LS of divisor */ | |
877 | serial_outp(up, UART_DLM, quot >> 8); /* MS of divisor */ | |
878 | if (up->port.type == PORT_16750) | |
879 | serial_outp(up, UART_FCR, fcr); /* set fcr */ | |
880 | serial_outp(up, UART_LCR, cval); /* reset DLAB */ | |
881 | up->lcr = cval; /* Save LCR */ | |
882 | if (up->port.type != PORT_16750) { | |
883 | if (fcr & UART_FCR_ENABLE_FIFO) { | |
884 | /* emulated UARTs (Lucent Venus 167x) need two steps */ | |
885 | serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); | |
886 | } | |
887 | serial_outp(up, UART_FCR, fcr); /* set fcr */ | |
888 | } | |
889 | ||
890 | up->cflag = cflag; | |
891 | ||
892 | spin_unlock_irqrestore(&up->port.lock, flags); | |
893 | } | |
894 | ||
895 | static void | |
606d099c AC |
896 | sunsu_set_termios(struct uart_port *port, struct ktermios *termios, |
897 | struct ktermios *old) | |
1da177e4 LT |
898 | { |
899 | unsigned int baud, quot; | |
900 | ||
901 | /* | |
902 | * Ask the core to calculate the divisor for us. | |
903 | */ | |
904 | baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); | |
905 | quot = uart_get_divisor(port, baud); | |
906 | ||
907 | sunsu_change_speed(port, termios->c_cflag, termios->c_iflag, quot); | |
908 | } | |
909 | ||
910 | static void sunsu_release_port(struct uart_port *port) | |
911 | { | |
912 | } | |
913 | ||
914 | static int sunsu_request_port(struct uart_port *port) | |
915 | { | |
916 | return 0; | |
917 | } | |
918 | ||
919 | static void sunsu_config_port(struct uart_port *port, int flags) | |
920 | { | |
921 | struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; | |
922 | ||
923 | if (flags & UART_CONFIG_TYPE) { | |
924 | /* | |
925 | * We are supposed to call autoconfig here, but this requires | |
926 | * splitting all the OBP probing crap from the UART probing. | |
927 | * We'll do it when we kill sunsu.c altogether. | |
928 | */ | |
929 | port->type = up->type_probed; /* XXX */ | |
930 | } | |
931 | } | |
932 | ||
933 | static int | |
934 | sunsu_verify_port(struct uart_port *port, struct serial_struct *ser) | |
935 | { | |
936 | return -EINVAL; | |
937 | } | |
938 | ||
939 | static const char * | |
940 | sunsu_type(struct uart_port *port) | |
941 | { | |
942 | int type = port->type; | |
943 | ||
944 | if (type >= ARRAY_SIZE(uart_config)) | |
945 | type = 0; | |
946 | return uart_config[type].name; | |
947 | } | |
948 | ||
949 | static struct uart_ops sunsu_pops = { | |
950 | .tx_empty = sunsu_tx_empty, | |
951 | .set_mctrl = sunsu_set_mctrl, | |
952 | .get_mctrl = sunsu_get_mctrl, | |
953 | .stop_tx = sunsu_stop_tx, | |
954 | .start_tx = sunsu_start_tx, | |
955 | .stop_rx = sunsu_stop_rx, | |
956 | .enable_ms = sunsu_enable_ms, | |
957 | .break_ctl = sunsu_break_ctl, | |
958 | .startup = sunsu_startup, | |
959 | .shutdown = sunsu_shutdown, | |
960 | .set_termios = sunsu_set_termios, | |
961 | .type = sunsu_type, | |
962 | .release_port = sunsu_release_port, | |
963 | .request_port = sunsu_request_port, | |
964 | .config_port = sunsu_config_port, | |
965 | .verify_port = sunsu_verify_port, | |
966 | }; | |
967 | ||
968 | #define UART_NR 4 | |
969 | ||
970 | static struct uart_sunsu_port sunsu_ports[UART_NR]; | |
971 | ||
972 | #ifdef CONFIG_SERIO | |
973 | ||
974 | static DEFINE_SPINLOCK(sunsu_serio_lock); | |
975 | ||
976 | static int sunsu_serio_write(struct serio *serio, unsigned char ch) | |
977 | { | |
978 | struct uart_sunsu_port *up = serio->port_data; | |
979 | unsigned long flags; | |
980 | int lsr; | |
981 | ||
982 | spin_lock_irqsave(&sunsu_serio_lock, flags); | |
983 | ||
984 | do { | |
985 | lsr = serial_in(up, UART_LSR); | |
986 | } while (!(lsr & UART_LSR_THRE)); | |
987 | ||
988 | /* Send the character out. */ | |
989 | serial_out(up, UART_TX, ch); | |
990 | ||
991 | spin_unlock_irqrestore(&sunsu_serio_lock, flags); | |
992 | ||
993 | return 0; | |
994 | } | |
995 | ||
996 | static int sunsu_serio_open(struct serio *serio) | |
997 | { | |
998 | struct uart_sunsu_port *up = serio->port_data; | |
999 | unsigned long flags; | |
1000 | int ret; | |
1001 | ||
1002 | spin_lock_irqsave(&sunsu_serio_lock, flags); | |
1003 | if (!up->serio_open) { | |
1004 | up->serio_open = 1; | |
1005 | ret = 0; | |
1006 | } else | |
1007 | ret = -EBUSY; | |
1008 | spin_unlock_irqrestore(&sunsu_serio_lock, flags); | |
1009 | ||
1010 | return ret; | |
1011 | } | |
1012 | ||
1013 | static void sunsu_serio_close(struct serio *serio) | |
1014 | { | |
1015 | struct uart_sunsu_port *up = serio->port_data; | |
1016 | unsigned long flags; | |
1017 | ||
1018 | spin_lock_irqsave(&sunsu_serio_lock, flags); | |
1019 | up->serio_open = 0; | |
1020 | spin_unlock_irqrestore(&sunsu_serio_lock, flags); | |
1021 | } | |
1022 | ||
1023 | #endif /* CONFIG_SERIO */ | |
1024 | ||
1025 | static void sunsu_autoconfig(struct uart_sunsu_port *up) | |
1026 | { | |
1027 | unsigned char status1, status2, scratch, scratch2, scratch3; | |
1028 | unsigned char save_lcr, save_mcr; | |
1da177e4 LT |
1029 | unsigned long flags; |
1030 | ||
1708d242 | 1031 | if (up->su_type == SU_PORT_NONE) |
1da177e4 LT |
1032 | return; |
1033 | ||
1034 | up->type_probed = PORT_UNKNOWN; | |
9b4a1617 | 1035 | up->port.iotype = UPIO_MEM; |
1da177e4 | 1036 | |
1da177e4 LT |
1037 | spin_lock_irqsave(&up->port.lock, flags); |
1038 | ||
ce8337cb | 1039 | if (!(up->port.flags & UPF_BUGGY_UART)) { |
1da177e4 LT |
1040 | /* |
1041 | * Do a simple existence test first; if we fail this, there's | |
1042 | * no point trying anything else. | |
1043 | * | |
1044 | * 0x80 is used as a nonsense port to prevent against false | |
1045 | * positives due to ISA bus float. The assumption is that | |
1046 | * 0x80 is a non-existent port; which should be safe since | |
1047 | * include/asm/io.h also makes this assumption. | |
1048 | */ | |
1049 | scratch = serial_inp(up, UART_IER); | |
1050 | serial_outp(up, UART_IER, 0); | |
1051 | #ifdef __i386__ | |
1052 | outb(0xff, 0x080); | |
1053 | #endif | |
1054 | scratch2 = serial_inp(up, UART_IER); | |
1055 | serial_outp(up, UART_IER, 0x0f); | |
1056 | #ifdef __i386__ | |
1057 | outb(0, 0x080); | |
1058 | #endif | |
1059 | scratch3 = serial_inp(up, UART_IER); | |
1060 | serial_outp(up, UART_IER, scratch); | |
1061 | if (scratch2 != 0 || scratch3 != 0x0F) | |
1062 | goto out; /* We failed; there's nothing here */ | |
1063 | } | |
1064 | ||
1065 | save_mcr = serial_in(up, UART_MCR); | |
1066 | save_lcr = serial_in(up, UART_LCR); | |
1067 | ||
1068 | /* | |
1069 | * Check to see if a UART is really there. Certain broken | |
1070 | * internal modems based on the Rockwell chipset fail this | |
1071 | * test, because they apparently don't implement the loopback | |
1072 | * test mode. So this test is skipped on the COM 1 through | |
1073 | * COM 4 ports. This *should* be safe, since no board | |
1074 | * manufacturer would be stupid enough to design a board | |
1075 | * that conflicts with COM 1-4 --- we hope! | |
1076 | */ | |
ce8337cb | 1077 | if (!(up->port.flags & UPF_SKIP_TEST)) { |
1da177e4 LT |
1078 | serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A); |
1079 | status1 = serial_inp(up, UART_MSR) & 0xF0; | |
1080 | serial_outp(up, UART_MCR, save_mcr); | |
1081 | if (status1 != 0x90) | |
1082 | goto out; /* We failed loopback test */ | |
1083 | } | |
1084 | serial_outp(up, UART_LCR, 0xBF); /* set up for StarTech test */ | |
1085 | serial_outp(up, UART_EFR, 0); /* EFR is the same as FCR */ | |
1086 | serial_outp(up, UART_LCR, 0); | |
1087 | serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); | |
1088 | scratch = serial_in(up, UART_IIR) >> 6; | |
1089 | switch (scratch) { | |
1090 | case 0: | |
1091 | up->port.type = PORT_16450; | |
1092 | break; | |
1093 | case 1: | |
1094 | up->port.type = PORT_UNKNOWN; | |
1095 | break; | |
1096 | case 2: | |
1097 | up->port.type = PORT_16550; | |
1098 | break; | |
1099 | case 3: | |
1100 | up->port.type = PORT_16550A; | |
1101 | break; | |
1102 | } | |
1103 | if (up->port.type == PORT_16550A) { | |
1104 | /* Check for Startech UART's */ | |
1105 | serial_outp(up, UART_LCR, UART_LCR_DLAB); | |
1106 | if (serial_in(up, UART_EFR) == 0) { | |
1107 | up->port.type = PORT_16650; | |
1108 | } else { | |
1109 | serial_outp(up, UART_LCR, 0xBF); | |
1110 | if (serial_in(up, UART_EFR) == 0) | |
1111 | up->port.type = PORT_16650V2; | |
1112 | } | |
1113 | } | |
1114 | if (up->port.type == PORT_16550A) { | |
1115 | /* Check for TI 16750 */ | |
1116 | serial_outp(up, UART_LCR, save_lcr | UART_LCR_DLAB); | |
1117 | serial_outp(up, UART_FCR, | |
1118 | UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); | |
1119 | scratch = serial_in(up, UART_IIR) >> 5; | |
1120 | if (scratch == 7) { | |
1121 | /* | |
1122 | * If this is a 16750, and not a cheap UART | |
1123 | * clone, then it should only go into 64 byte | |
1124 | * mode if the UART_FCR7_64BYTE bit was set | |
1125 | * while UART_LCR_DLAB was latched. | |
1126 | */ | |
1127 | serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); | |
1128 | serial_outp(up, UART_LCR, 0); | |
1129 | serial_outp(up, UART_FCR, | |
1130 | UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); | |
1131 | scratch = serial_in(up, UART_IIR) >> 5; | |
1132 | if (scratch == 6) | |
1133 | up->port.type = PORT_16750; | |
1134 | } | |
1135 | serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); | |
1136 | } | |
1137 | serial_outp(up, UART_LCR, save_lcr); | |
1138 | if (up->port.type == PORT_16450) { | |
1139 | scratch = serial_in(up, UART_SCR); | |
1140 | serial_outp(up, UART_SCR, 0xa5); | |
1141 | status1 = serial_in(up, UART_SCR); | |
1142 | serial_outp(up, UART_SCR, 0x5a); | |
1143 | status2 = serial_in(up, UART_SCR); | |
1144 | serial_outp(up, UART_SCR, scratch); | |
1145 | ||
1146 | if ((status1 != 0xa5) || (status2 != 0x5a)) | |
1147 | up->port.type = PORT_8250; | |
1148 | } | |
1149 | ||
1150 | up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size; | |
1151 | ||
1152 | if (up->port.type == PORT_UNKNOWN) | |
1153 | goto out; | |
1154 | up->type_probed = up->port.type; /* XXX */ | |
1155 | ||
1156 | /* | |
1157 | * Reset the UART. | |
1158 | */ | |
1159 | #ifdef CONFIG_SERIAL_8250_RSA | |
1160 | if (up->port.type == PORT_RSA) | |
1161 | serial_outp(up, UART_RSA_FRR, 0); | |
1162 | #endif | |
1163 | serial_outp(up, UART_MCR, save_mcr); | |
1164 | serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO | | |
1165 | UART_FCR_CLEAR_RCVR | | |
1166 | UART_FCR_CLEAR_XMIT)); | |
1167 | serial_outp(up, UART_FCR, 0); | |
1168 | (void)serial_in(up, UART_RX); | |
1169 | serial_outp(up, UART_IER, 0); | |
1170 | ||
1171 | out: | |
1172 | spin_unlock_irqrestore(&up->port.lock, flags); | |
1173 | } | |
1174 | ||
1175 | static struct uart_driver sunsu_reg = { | |
1176 | .owner = THIS_MODULE, | |
32039f49 | 1177 | .driver_name = "sunsu", |
1da177e4 LT |
1178 | .dev_name = "ttyS", |
1179 | .major = TTY_MAJOR, | |
1180 | }; | |
1181 | ||
f5d378ac | 1182 | static int __devinit sunsu_kbd_ms_init(struct uart_sunsu_port *up) |
1da177e4 | 1183 | { |
623f41eb | 1184 | int quot, baud; |
1da177e4 LT |
1185 | #ifdef CONFIG_SERIO |
1186 | struct serio *serio; | |
1187 | #endif | |
1188 | ||
623f41eb | 1189 | if (up->su_type == SU_PORT_KBD) { |
1da177e4 | 1190 | up->cflag = B1200 | CS8 | CLOCAL | CREAD; |
623f41eb DM |
1191 | baud = 1200; |
1192 | } else { | |
1da177e4 | 1193 | up->cflag = B4800 | CS8 | CLOCAL | CREAD; |
623f41eb DM |
1194 | baud = 4800; |
1195 | } | |
1196 | quot = up->port.uartclk / (16 * baud); | |
1da177e4 LT |
1197 | |
1198 | sunsu_autoconfig(up); | |
1199 | if (up->port.type == PORT_UNKNOWN) | |
1708d242 | 1200 | return -ENODEV; |
1da177e4 | 1201 | |
4f1296a5 | 1202 | printk("%s: %s port at %llx, irq %u\n", |
61c7a080 | 1203 | to_of_device(up->port.dev)->dev.of_node->full_name, |
c964521c | 1204 | (up->su_type == SU_PORT_KBD) ? "Keyboard" : "Mouse", |
4f1296a5 DM |
1205 | (unsigned long long) up->port.mapbase, |
1206 | up->port.irq); | |
c964521c | 1207 | |
1da177e4 | 1208 | #ifdef CONFIG_SERIO |
1708d242 DM |
1209 | serio = &up->serio; |
1210 | serio->port_data = up; | |
1da177e4 | 1211 | |
1708d242 DM |
1212 | serio->id.type = SERIO_RS232; |
1213 | if (up->su_type == SU_PORT_KBD) { | |
1214 | serio->id.proto = SERIO_SUNKBD; | |
1215 | strlcpy(serio->name, "sukbd", sizeof(serio->name)); | |
1da177e4 | 1216 | } else { |
1708d242 DM |
1217 | serio->id.proto = SERIO_SUN; |
1218 | serio->id.extra = 1; | |
1219 | strlcpy(serio->name, "sums", sizeof(serio->name)); | |
1da177e4 | 1220 | } |
1708d242 DM |
1221 | strlcpy(serio->phys, |
1222 | (!(up->port.line & 1) ? "su/serio0" : "su/serio1"), | |
1223 | sizeof(serio->phys)); | |
1224 | ||
1225 | serio->write = sunsu_serio_write; | |
1226 | serio->open = sunsu_serio_open; | |
1227 | serio->close = sunsu_serio_close; | |
1228 | serio->dev.parent = up->port.dev; | |
1229 | ||
1230 | serio_register_port(serio); | |
1da177e4 LT |
1231 | #endif |
1232 | ||
623f41eb DM |
1233 | sunsu_change_speed(&up->port, up->cflag, 0, quot); |
1234 | ||
1da177e4 LT |
1235 | sunsu_startup(&up->port); |
1236 | return 0; | |
1237 | } | |
1238 | ||
1239 | /* | |
1240 | * ------------------------------------------------------------ | |
1241 | * Serial console driver | |
1242 | * ------------------------------------------------------------ | |
1243 | */ | |
1244 | ||
1245 | #ifdef CONFIG_SERIAL_SUNSU_CONSOLE | |
1246 | ||
1247 | #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) | |
1248 | ||
1249 | /* | |
1250 | * Wait for transmitter & holding register to empty | |
1251 | */ | |
1252 | static __inline__ void wait_for_xmitr(struct uart_sunsu_port *up) | |
1253 | { | |
1254 | unsigned int status, tmout = 10000; | |
1255 | ||
1256 | /* Wait up to 10ms for the character(s) to be sent. */ | |
1257 | do { | |
1258 | status = serial_in(up, UART_LSR); | |
1259 | ||
1260 | if (status & UART_LSR_BI) | |
1261 | up->lsr_break_flag = UART_LSR_BI; | |
1262 | ||
1263 | if (--tmout == 0) | |
1264 | break; | |
1265 | udelay(1); | |
1266 | } while ((status & BOTH_EMPTY) != BOTH_EMPTY); | |
1267 | ||
1268 | /* Wait up to 1s for flow control if necessary */ | |
ce8337cb | 1269 | if (up->port.flags & UPF_CONS_FLOW) { |
1da177e4 LT |
1270 | tmout = 1000000; |
1271 | while (--tmout && | |
1272 | ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0)) | |
1273 | udelay(1); | |
1274 | } | |
1275 | } | |
1276 | ||
d358788f RK |
1277 | static void sunsu_console_putchar(struct uart_port *port, int ch) |
1278 | { | |
1279 | struct uart_sunsu_port *up = (struct uart_sunsu_port *)port; | |
1280 | ||
1281 | wait_for_xmitr(up); | |
1282 | serial_out(up, UART_TX, ch); | |
1283 | } | |
1284 | ||
1da177e4 LT |
1285 | /* |
1286 | * Print a string to the serial port trying not to disturb | |
1287 | * any possible real use of the port... | |
1288 | */ | |
1289 | static void sunsu_console_write(struct console *co, const char *s, | |
1290 | unsigned int count) | |
1291 | { | |
1292 | struct uart_sunsu_port *up = &sunsu_ports[co->index]; | |
f3c681c0 | 1293 | unsigned long flags; |
1da177e4 | 1294 | unsigned int ier; |
f3c681c0 DM |
1295 | int locked = 1; |
1296 | ||
1297 | local_irq_save(flags); | |
1298 | if (up->port.sysrq) { | |
1299 | locked = 0; | |
1300 | } else if (oops_in_progress) { | |
1301 | locked = spin_trylock(&up->port.lock); | |
1302 | } else | |
1303 | spin_lock(&up->port.lock); | |
1da177e4 LT |
1304 | |
1305 | /* | |
1306 | * First save the UER then disable the interrupts | |
1307 | */ | |
1308 | ier = serial_in(up, UART_IER); | |
1309 | serial_out(up, UART_IER, 0); | |
1310 | ||
d358788f | 1311 | uart_console_write(&up->port, s, count, sunsu_console_putchar); |
1da177e4 LT |
1312 | |
1313 | /* | |
1314 | * Finally, wait for transmitter to become empty | |
1315 | * and restore the IER | |
1316 | */ | |
1317 | wait_for_xmitr(up); | |
1318 | serial_out(up, UART_IER, ier); | |
f3c681c0 DM |
1319 | |
1320 | if (locked) | |
1321 | spin_unlock(&up->port.lock); | |
1322 | local_irq_restore(flags); | |
1da177e4 LT |
1323 | } |
1324 | ||
1325 | /* | |
1326 | * Setup initial baud/bits/parity. We do two things here: | |
1327 | * - construct a cflag setting for the first su_open() | |
1328 | * - initialize the serial port | |
1329 | * Return non-zero if we didn't find a serial port. | |
1330 | */ | |
90a660a4 | 1331 | static int __init sunsu_console_setup(struct console *co, char *options) |
1da177e4 | 1332 | { |
be24656a DM |
1333 | static struct ktermios dummy; |
1334 | struct ktermios termios; | |
1da177e4 | 1335 | struct uart_port *port; |
1da177e4 LT |
1336 | |
1337 | printk("Console: ttyS%d (SU)\n", | |
1338 | (sunsu_reg.minor - 64) + co->index); | |
1339 | ||
1340 | /* | |
1341 | * Check whether an invalid uart number has been specified, and | |
1342 | * if so, search for the first available port that does have | |
1343 | * console support. | |
1344 | */ | |
1345 | if (co->index >= UART_NR) | |
1346 | co->index = 0; | |
1347 | port = &sunsu_ports[co->index].port; | |
1348 | ||
1349 | /* | |
1350 | * Temporary fix. | |
1351 | */ | |
1352 | spin_lock_init(&port->lock); | |
1353 | ||
be24656a | 1354 | /* Get firmware console settings. */ |
61c7a080 | 1355 | sunserial_console_termios(co, to_of_device(port->dev)->dev.of_node); |
1da177e4 | 1356 | |
be24656a DM |
1357 | memset(&termios, 0, sizeof(struct ktermios)); |
1358 | termios.c_cflag = co->cflag; | |
1359 | port->mctrl |= TIOCM_DTR; | |
1360 | port->ops->set_termios(port, &termios, &dummy); | |
1361 | ||
1362 | return 0; | |
1da177e4 LT |
1363 | } |
1364 | ||
90a660a4 | 1365 | static struct console sunsu_console = { |
1da177e4 LT |
1366 | .name = "ttyS", |
1367 | .write = sunsu_console_write, | |
1368 | .device = uart_console_device, | |
1369 | .setup = sunsu_console_setup, | |
1370 | .flags = CON_PRINTBUFFER, | |
1371 | .index = -1, | |
1372 | .data = &sunsu_reg, | |
1373 | }; | |
1da177e4 LT |
1374 | |
1375 | /* | |
1376 | * Register console. | |
1377 | */ | |
1378 | ||
c73fcc84 | 1379 | static inline struct console *SUNSU_CONSOLE(void) |
1da177e4 | 1380 | { |
90a660a4 | 1381 | return &sunsu_console; |
1da177e4 LT |
1382 | } |
1383 | #else | |
c73fcc84 | 1384 | #define SUNSU_CONSOLE() (NULL) |
1da177e4 LT |
1385 | #define sunsu_serial_console_init() do { } while (0) |
1386 | #endif | |
1387 | ||
1708d242 | 1388 | static enum su_type __devinit su_get_type(struct device_node *dp) |
1da177e4 | 1389 | { |
1708d242 | 1390 | struct device_node *ap = of_find_node_by_path("/aliases"); |
1da177e4 | 1391 | |
1708d242 | 1392 | if (ap) { |
ccf0dec6 SR |
1393 | const char *keyb = of_get_property(ap, "keyboard", NULL); |
1394 | const char *ms = of_get_property(ap, "mouse", NULL); | |
1da177e4 | 1395 | |
1708d242 DM |
1396 | if (keyb) { |
1397 | if (dp == of_find_node_by_path(keyb)) | |
1398 | return SU_PORT_KBD; | |
1399 | } | |
1400 | if (ms) { | |
1401 | if (dp == of_find_node_by_path(ms)) | |
1402 | return SU_PORT_MS; | |
1403 | } | |
1404 | } | |
1da177e4 | 1405 | |
1708d242 DM |
1406 | return SU_PORT_PORT; |
1407 | } | |
1da177e4 | 1408 | |
1708d242 DM |
1409 | static int __devinit su_probe(struct of_device *op, const struct of_device_id *match) |
1410 | { | |
1411 | static int inst; | |
61c7a080 | 1412 | struct device_node *dp = op->dev.of_node; |
1708d242 DM |
1413 | struct uart_sunsu_port *up; |
1414 | struct resource *rp; | |
91d1ed1a | 1415 | enum su_type type; |
1917d17b | 1416 | bool ignore_line; |
1708d242 | 1417 | int err; |
1da177e4 | 1418 | |
91d1ed1a DM |
1419 | type = su_get_type(dp); |
1420 | if (type == SU_PORT_PORT) { | |
1421 | if (inst >= UART_NR) | |
1422 | return -EINVAL; | |
1423 | up = &sunsu_ports[inst]; | |
1424 | } else { | |
1425 | up = kzalloc(sizeof(*up), GFP_KERNEL); | |
1426 | if (!up) | |
1427 | return -ENOMEM; | |
1428 | } | |
1da177e4 | 1429 | |
1708d242 | 1430 | up->port.line = inst; |
1da177e4 | 1431 | |
1708d242 | 1432 | spin_lock_init(&up->port.lock); |
1da177e4 | 1433 | |
91d1ed1a | 1434 | up->su_type = type; |
f5deb807 | 1435 | |
1708d242 | 1436 | rp = &op->resource[0]; |
91d1ed1a | 1437 | up->port.mapbase = rp->start; |
1708d242 DM |
1438 | up->reg_size = (rp->end - rp->start) + 1; |
1439 | up->port.membase = of_ioremap(rp, 0, up->reg_size, "su"); | |
91d1ed1a DM |
1440 | if (!up->port.membase) { |
1441 | if (type != SU_PORT_PORT) | |
1442 | kfree(up); | |
1708d242 | 1443 | return -ENOMEM; |
91d1ed1a | 1444 | } |
1ddb7c98 | 1445 | |
1636f8ac | 1446 | up->port.irq = op->archdata.irqs[0]; |
1da177e4 | 1447 | |
1708d242 | 1448 | up->port.dev = &op->dev; |
1da177e4 | 1449 | |
1708d242 DM |
1450 | up->port.type = PORT_UNKNOWN; |
1451 | up->port.uartclk = (SU_BASE_BAUD * 16); | |
1da177e4 | 1452 | |
1708d242 DM |
1453 | err = 0; |
1454 | if (up->su_type == SU_PORT_KBD || up->su_type == SU_PORT_MS) { | |
1455 | err = sunsu_kbd_ms_init(up); | |
91d1ed1a | 1456 | if (err) { |
c4a3987f JL |
1457 | of_iounmap(&op->resource[0], |
1458 | up->port.membase, up->reg_size); | |
91d1ed1a | 1459 | kfree(up); |
c4a3987f | 1460 | return err; |
91d1ed1a DM |
1461 | } |
1462 | dev_set_drvdata(&op->dev, up); | |
a1d22d32 DM |
1463 | |
1464 | return 0; | |
1da177e4 LT |
1465 | } |
1466 | ||
1708d242 | 1467 | up->port.flags |= UPF_BOOT_AUTOCONF; |
1da177e4 | 1468 | |
1708d242 | 1469 | sunsu_autoconfig(up); |
1da177e4 | 1470 | |
1708d242 DM |
1471 | err = -ENODEV; |
1472 | if (up->port.type == PORT_UNKNOWN) | |
1473 | goto out_unmap; | |
1da177e4 | 1474 | |
1708d242 | 1475 | up->port.ops = &sunsu_pops; |
1da177e4 | 1476 | |
1917d17b DM |
1477 | ignore_line = false; |
1478 | if (!strcmp(dp->name, "rsc-console") || | |
1479 | !strcmp(dp->name, "lom-console")) | |
1480 | ignore_line = true; | |
1481 | ||
c73fcc84 | 1482 | sunserial_console_match(SUNSU_CONSOLE(), dp, |
4e3533d0 | 1483 | &sunsu_reg, up->port.line, |
1917d17b | 1484 | ignore_line); |
1708d242 DM |
1485 | err = uart_add_one_port(&sunsu_reg, &up->port); |
1486 | if (err) | |
1487 | goto out_unmap; | |
1da177e4 | 1488 | |
1708d242 | 1489 | dev_set_drvdata(&op->dev, up); |
1da177e4 | 1490 | |
1708d242 | 1491 | inst++; |
1da177e4 | 1492 | |
1708d242 DM |
1493 | return 0; |
1494 | ||
1495 | out_unmap: | |
e3a411a3 | 1496 | of_iounmap(&op->resource[0], up->port.membase, up->reg_size); |
1708d242 | 1497 | return err; |
1da177e4 LT |
1498 | } |
1499 | ||
e3a411a3 | 1500 | static int __devexit su_remove(struct of_device *op) |
1da177e4 | 1501 | { |
e3a411a3 | 1502 | struct uart_sunsu_port *up = dev_get_drvdata(&op->dev); |
9616ff43 | 1503 | bool kbdms = false; |
1da177e4 | 1504 | |
1708d242 | 1505 | if (up->su_type == SU_PORT_MS || |
9616ff43 DM |
1506 | up->su_type == SU_PORT_KBD) |
1507 | kbdms = true; | |
1508 | ||
1509 | if (kbdms) { | |
1708d242 DM |
1510 | #ifdef CONFIG_SERIO |
1511 | serio_unregister_port(&up->serio); | |
1512 | #endif | |
9616ff43 | 1513 | } else if (up->port.type != PORT_UNKNOWN) |
1708d242 | 1514 | uart_remove_one_port(&sunsu_reg, &up->port); |
91d1ed1a | 1515 | |
65da4d81 | 1516 | if (up->port.membase) |
e3a411a3 | 1517 | of_iounmap(&op->resource[0], up->port.membase, up->reg_size); |
65da4d81 | 1518 | |
9616ff43 DM |
1519 | if (kbdms) |
1520 | kfree(up); | |
1521 | ||
e3a411a3 | 1522 | dev_set_drvdata(&op->dev, NULL); |
1da177e4 | 1523 | |
1708d242 DM |
1524 | return 0; |
1525 | } | |
1da177e4 | 1526 | |
fd098316 | 1527 | static const struct of_device_id su_match[] = { |
1708d242 DM |
1528 | { |
1529 | .name = "su", | |
1530 | }, | |
1531 | { | |
1532 | .name = "su_pnp", | |
1533 | }, | |
1534 | { | |
1535 | .name = "serial", | |
1536 | .compatible = "su", | |
1537 | }, | |
8301d386 DM |
1538 | { |
1539 | .type = "serial", | |
1540 | .compatible = "su", | |
1541 | }, | |
1708d242 DM |
1542 | {}, |
1543 | }; | |
1544 | MODULE_DEVICE_TABLE(of, su_match); | |
1da177e4 | 1545 | |
1708d242 | 1546 | static struct of_platform_driver su_driver = { |
4018294b GL |
1547 | .driver = { |
1548 | .name = "su", | |
1549 | .owner = THIS_MODULE, | |
1550 | .of_match_table = su_match, | |
1551 | }, | |
1708d242 DM |
1552 | .probe = su_probe, |
1553 | .remove = __devexit_p(su_remove), | |
1554 | }; | |
1da177e4 | 1555 | |
1708d242 DM |
1556 | static int __init sunsu_init(void) |
1557 | { | |
1558 | struct device_node *dp; | |
1559 | int err; | |
58d784a5 | 1560 | int num_uart = 0; |
1da177e4 | 1561 | |
1708d242 DM |
1562 | for_each_node_by_name(dp, "su") { |
1563 | if (su_get_type(dp) == SU_PORT_PORT) | |
1564 | num_uart++; | |
1da177e4 | 1565 | } |
1708d242 DM |
1566 | for_each_node_by_name(dp, "su_pnp") { |
1567 | if (su_get_type(dp) == SU_PORT_PORT) | |
1568 | num_uart++; | |
1569 | } | |
1570 | for_each_node_by_name(dp, "serial") { | |
1571 | if (of_device_is_compatible(dp, "su")) { | |
1572 | if (su_get_type(dp) == SU_PORT_PORT) | |
1573 | num_uart++; | |
1574 | } | |
1da177e4 | 1575 | } |
8301d386 DM |
1576 | for_each_node_by_type(dp, "serial") { |
1577 | if (of_device_is_compatible(dp, "su")) { | |
1578 | if (su_get_type(dp) == SU_PORT_PORT) | |
1579 | num_uart++; | |
1580 | } | |
1581 | } | |
1da177e4 | 1582 | |
1708d242 | 1583 | if (num_uart) { |
58d784a5 | 1584 | err = sunserial_register_minors(&sunsu_reg, num_uart); |
1708d242 DM |
1585 | if (err) |
1586 | return err; | |
1708d242 | 1587 | } |
1da177e4 | 1588 | |
1ab1d63a | 1589 | err = of_register_platform_driver(&su_driver); |
1708d242 | 1590 | if (err && num_uart) |
58d784a5 | 1591 | sunserial_unregister_minors(&sunsu_reg, num_uart); |
1da177e4 | 1592 | |
1708d242 | 1593 | return err; |
1da177e4 LT |
1594 | } |
1595 | ||
1596 | static void __exit sunsu_exit(void) | |
1597 | { | |
58d784a5 MH |
1598 | if (sunsu_reg.nr) |
1599 | sunserial_unregister_minors(&sunsu_reg, sunsu_reg.nr); | |
1da177e4 LT |
1600 | } |
1601 | ||
1708d242 | 1602 | module_init(sunsu_init); |
1da177e4 | 1603 | module_exit(sunsu_exit); |
9efc3715 DM |
1604 | |
1605 | MODULE_AUTHOR("Eddie C. Dost, Peter Zaitcev, and David S. Miller"); | |
1606 | MODULE_DESCRIPTION("Sun SU serial port driver"); | |
1607 | MODULE_VERSION("2.0"); | |
9a2a9bb2 | 1608 | MODULE_LICENSE("GPL"); |