Commit | Line | Data |
---|---|---|
011f23a3 MW |
1 | /* |
2 | * Driver for Cirrus Logic EP93xx SPI controller. | |
3 | * | |
626a96db | 4 | * Copyright (C) 2010-2011 Mika Westerberg |
011f23a3 MW |
5 | * |
6 | * Explicit FIFO handling code was inspired by amba-pl022 driver. | |
7 | * | |
8 | * Chip select support using other than built-in GPIOs by H. Hartley Sweeten. | |
9 | * | |
10 | * For more information about the SPI controller see documentation on Cirrus | |
11 | * Logic web site: | |
12 | * http://www.cirrus.com/en/pubs/manual/EP93xx_Users_Guide_UM1.pdf | |
13 | * | |
14 | * This program is free software; you can redistribute it and/or modify | |
15 | * it under the terms of the GNU General Public License version 2 as | |
16 | * published by the Free Software Foundation. | |
17 | */ | |
18 | ||
19 | #include <linux/io.h> | |
20 | #include <linux/clk.h> | |
21 | #include <linux/err.h> | |
22 | #include <linux/delay.h> | |
23 | #include <linux/device.h> | |
626a96db | 24 | #include <linux/dmaengine.h> |
011f23a3 MW |
25 | #include <linux/bitops.h> |
26 | #include <linux/interrupt.h> | |
27 | #include <linux/platform_device.h> | |
28 | #include <linux/workqueue.h> | |
29 | #include <linux/sched.h> | |
626a96db | 30 | #include <linux/scatterlist.h> |
011f23a3 MW |
31 | #include <linux/spi/spi.h> |
32 | ||
626a96db | 33 | #include <mach/dma.h> |
011f23a3 MW |
34 | #include <mach/ep93xx_spi.h> |
35 | ||
36 | #define SSPCR0 0x0000 | |
37 | #define SSPCR0_MODE_SHIFT 6 | |
38 | #define SSPCR0_SCR_SHIFT 8 | |
39 | ||
40 | #define SSPCR1 0x0004 | |
41 | #define SSPCR1_RIE BIT(0) | |
42 | #define SSPCR1_TIE BIT(1) | |
43 | #define SSPCR1_RORIE BIT(2) | |
44 | #define SSPCR1_LBM BIT(3) | |
45 | #define SSPCR1_SSE BIT(4) | |
46 | #define SSPCR1_MS BIT(5) | |
47 | #define SSPCR1_SOD BIT(6) | |
48 | ||
49 | #define SSPDR 0x0008 | |
50 | ||
51 | #define SSPSR 0x000c | |
52 | #define SSPSR_TFE BIT(0) | |
53 | #define SSPSR_TNF BIT(1) | |
54 | #define SSPSR_RNE BIT(2) | |
55 | #define SSPSR_RFF BIT(3) | |
56 | #define SSPSR_BSY BIT(4) | |
57 | #define SSPCPSR 0x0010 | |
58 | ||
59 | #define SSPIIR 0x0014 | |
60 | #define SSPIIR_RIS BIT(0) | |
61 | #define SSPIIR_TIS BIT(1) | |
62 | #define SSPIIR_RORIS BIT(2) | |
63 | #define SSPICR SSPIIR | |
64 | ||
65 | /* timeout in milliseconds */ | |
66 | #define SPI_TIMEOUT 5 | |
67 | /* maximum depth of RX/TX FIFO */ | |
68 | #define SPI_FIFO_SIZE 8 | |
69 | ||
70 | /** | |
71 | * struct ep93xx_spi - EP93xx SPI controller structure | |
72 | * @lock: spinlock that protects concurrent accesses to fields @running, | |
73 | * @current_msg and @msg_queue | |
74 | * @pdev: pointer to platform device | |
75 | * @clk: clock for the controller | |
76 | * @regs_base: pointer to ioremap()'d registers | |
626a96db | 77 | * @sspdr_phys: physical address of the SSPDR register |
011f23a3 MW |
78 | * @irq: IRQ number used by the driver |
79 | * @min_rate: minimum clock rate (in Hz) supported by the controller | |
80 | * @max_rate: maximum clock rate (in Hz) supported by the controller | |
81 | * @running: is the queue running | |
82 | * @wq: workqueue used by the driver | |
83 | * @msg_work: work that is queued for the driver | |
84 | * @wait: wait here until given transfer is completed | |
85 | * @msg_queue: queue for the messages | |
86 | * @current_msg: message that is currently processed (or %NULL if none) | |
87 | * @tx: current byte in transfer to transmit | |
88 | * @rx: current byte in transfer to receive | |
89 | * @fifo_level: how full is FIFO (%0..%SPI_FIFO_SIZE - %1). Receiving one | |
90 | * frame decreases this level and sending one frame increases it. | |
626a96db MW |
91 | * @dma_rx: RX DMA channel |
92 | * @dma_tx: TX DMA channel | |
93 | * @dma_rx_data: RX parameters passed to the DMA engine | |
94 | * @dma_tx_data: TX parameters passed to the DMA engine | |
95 | * @rx_sgt: sg table for RX transfers | |
96 | * @tx_sgt: sg table for TX transfers | |
97 | * @zeropage: dummy page used as RX buffer when only TX buffer is passed in by | |
98 | * the client | |
011f23a3 MW |
99 | * |
100 | * This structure holds EP93xx SPI controller specific information. When | |
101 | * @running is %true, driver accepts transfer requests from protocol drivers. | |
102 | * @current_msg is used to hold pointer to the message that is currently | |
103 | * processed. If @current_msg is %NULL, it means that no processing is going | |
104 | * on. | |
105 | * | |
106 | * Most of the fields are only written once and they can be accessed without | |
107 | * taking the @lock. Fields that are accessed concurrently are: @current_msg, | |
108 | * @running, and @msg_queue. | |
109 | */ | |
110 | struct ep93xx_spi { | |
111 | spinlock_t lock; | |
112 | const struct platform_device *pdev; | |
113 | struct clk *clk; | |
114 | void __iomem *regs_base; | |
626a96db | 115 | unsigned long sspdr_phys; |
011f23a3 MW |
116 | int irq; |
117 | unsigned long min_rate; | |
118 | unsigned long max_rate; | |
119 | bool running; | |
120 | struct workqueue_struct *wq; | |
121 | struct work_struct msg_work; | |
122 | struct completion wait; | |
123 | struct list_head msg_queue; | |
124 | struct spi_message *current_msg; | |
125 | size_t tx; | |
126 | size_t rx; | |
127 | size_t fifo_level; | |
626a96db MW |
128 | struct dma_chan *dma_rx; |
129 | struct dma_chan *dma_tx; | |
130 | struct ep93xx_dma_data dma_rx_data; | |
131 | struct ep93xx_dma_data dma_tx_data; | |
132 | struct sg_table rx_sgt; | |
133 | struct sg_table tx_sgt; | |
134 | void *zeropage; | |
011f23a3 MW |
135 | }; |
136 | ||
137 | /** | |
138 | * struct ep93xx_spi_chip - SPI device hardware settings | |
139 | * @spi: back pointer to the SPI device | |
140 | * @rate: max rate in hz this chip supports | |
141 | * @div_cpsr: cpsr (pre-scaler) divider | |
142 | * @div_scr: scr divider | |
143 | * @dss: bits per word (4 - 16 bits) | |
144 | * @ops: private chip operations | |
145 | * | |
146 | * This structure is used to store hardware register specific settings for each | |
147 | * SPI device. Settings are written to hardware by function | |
148 | * ep93xx_spi_chip_setup(). | |
149 | */ | |
150 | struct ep93xx_spi_chip { | |
151 | const struct spi_device *spi; | |
152 | unsigned long rate; | |
153 | u8 div_cpsr; | |
154 | u8 div_scr; | |
155 | u8 dss; | |
156 | struct ep93xx_spi_chip_ops *ops; | |
157 | }; | |
158 | ||
159 | /* converts bits per word to CR0.DSS value */ | |
160 | #define bits_per_word_to_dss(bpw) ((bpw) - 1) | |
161 | ||
162 | static inline void | |
163 | ep93xx_spi_write_u8(const struct ep93xx_spi *espi, u16 reg, u8 value) | |
164 | { | |
165 | __raw_writeb(value, espi->regs_base + reg); | |
166 | } | |
167 | ||
168 | static inline u8 | |
169 | ep93xx_spi_read_u8(const struct ep93xx_spi *spi, u16 reg) | |
170 | { | |
171 | return __raw_readb(spi->regs_base + reg); | |
172 | } | |
173 | ||
174 | static inline void | |
175 | ep93xx_spi_write_u16(const struct ep93xx_spi *espi, u16 reg, u16 value) | |
176 | { | |
177 | __raw_writew(value, espi->regs_base + reg); | |
178 | } | |
179 | ||
180 | static inline u16 | |
181 | ep93xx_spi_read_u16(const struct ep93xx_spi *spi, u16 reg) | |
182 | { | |
183 | return __raw_readw(spi->regs_base + reg); | |
184 | } | |
185 | ||
186 | static int ep93xx_spi_enable(const struct ep93xx_spi *espi) | |
187 | { | |
188 | u8 regval; | |
189 | int err; | |
190 | ||
191 | err = clk_enable(espi->clk); | |
192 | if (err) | |
193 | return err; | |
194 | ||
195 | regval = ep93xx_spi_read_u8(espi, SSPCR1); | |
196 | regval |= SSPCR1_SSE; | |
197 | ep93xx_spi_write_u8(espi, SSPCR1, regval); | |
198 | ||
199 | return 0; | |
200 | } | |
201 | ||
202 | static void ep93xx_spi_disable(const struct ep93xx_spi *espi) | |
203 | { | |
204 | u8 regval; | |
205 | ||
206 | regval = ep93xx_spi_read_u8(espi, SSPCR1); | |
207 | regval &= ~SSPCR1_SSE; | |
208 | ep93xx_spi_write_u8(espi, SSPCR1, regval); | |
209 | ||
210 | clk_disable(espi->clk); | |
211 | } | |
212 | ||
213 | static void ep93xx_spi_enable_interrupts(const struct ep93xx_spi *espi) | |
214 | { | |
215 | u8 regval; | |
216 | ||
217 | regval = ep93xx_spi_read_u8(espi, SSPCR1); | |
218 | regval |= (SSPCR1_RORIE | SSPCR1_TIE | SSPCR1_RIE); | |
219 | ep93xx_spi_write_u8(espi, SSPCR1, regval); | |
220 | } | |
221 | ||
222 | static void ep93xx_spi_disable_interrupts(const struct ep93xx_spi *espi) | |
223 | { | |
224 | u8 regval; | |
225 | ||
226 | regval = ep93xx_spi_read_u8(espi, SSPCR1); | |
227 | regval &= ~(SSPCR1_RORIE | SSPCR1_TIE | SSPCR1_RIE); | |
228 | ep93xx_spi_write_u8(espi, SSPCR1, regval); | |
229 | } | |
230 | ||
231 | /** | |
232 | * ep93xx_spi_calc_divisors() - calculates SPI clock divisors | |
233 | * @espi: ep93xx SPI controller struct | |
234 | * @chip: divisors are calculated for this chip | |
235 | * @rate: desired SPI output clock rate | |
236 | * | |
237 | * Function calculates cpsr (clock pre-scaler) and scr divisors based on | |
238 | * given @rate and places them to @chip->div_cpsr and @chip->div_scr. If, | |
239 | * for some reason, divisors cannot be calculated nothing is stored and | |
240 | * %-EINVAL is returned. | |
241 | */ | |
242 | static int ep93xx_spi_calc_divisors(const struct ep93xx_spi *espi, | |
243 | struct ep93xx_spi_chip *chip, | |
244 | unsigned long rate) | |
245 | { | |
246 | unsigned long spi_clk_rate = clk_get_rate(espi->clk); | |
247 | int cpsr, scr; | |
248 | ||
249 | /* | |
250 | * Make sure that max value is between values supported by the | |
251 | * controller. Note that minimum value is already checked in | |
252 | * ep93xx_spi_transfer(). | |
253 | */ | |
254 | rate = clamp(rate, espi->min_rate, espi->max_rate); | |
255 | ||
256 | /* | |
257 | * Calculate divisors so that we can get speed according the | |
258 | * following formula: | |
259 | * rate = spi_clock_rate / (cpsr * (1 + scr)) | |
260 | * | |
261 | * cpsr must be even number and starts from 2, scr can be any number | |
262 | * between 0 and 255. | |
263 | */ | |
264 | for (cpsr = 2; cpsr <= 254; cpsr += 2) { | |
265 | for (scr = 0; scr <= 255; scr++) { | |
266 | if ((spi_clk_rate / (cpsr * (scr + 1))) <= rate) { | |
267 | chip->div_scr = (u8)scr; | |
268 | chip->div_cpsr = (u8)cpsr; | |
269 | return 0; | |
270 | } | |
271 | } | |
272 | } | |
273 | ||
274 | return -EINVAL; | |
275 | } | |
276 | ||
277 | static void ep93xx_spi_cs_control(struct spi_device *spi, bool control) | |
278 | { | |
279 | struct ep93xx_spi_chip *chip = spi_get_ctldata(spi); | |
280 | int value = (spi->mode & SPI_CS_HIGH) ? control : !control; | |
281 | ||
282 | if (chip->ops && chip->ops->cs_control) | |
283 | chip->ops->cs_control(spi, value); | |
284 | } | |
285 | ||
286 | /** | |
287 | * ep93xx_spi_setup() - setup an SPI device | |
288 | * @spi: SPI device to setup | |
289 | * | |
290 | * This function sets up SPI device mode, speed etc. Can be called multiple | |
291 | * times for a single device. Returns %0 in case of success, negative error in | |
292 | * case of failure. When this function returns success, the device is | |
293 | * deselected. | |
294 | */ | |
295 | static int ep93xx_spi_setup(struct spi_device *spi) | |
296 | { | |
297 | struct ep93xx_spi *espi = spi_master_get_devdata(spi->master); | |
298 | struct ep93xx_spi_chip *chip; | |
299 | ||
300 | if (spi->bits_per_word < 4 || spi->bits_per_word > 16) { | |
301 | dev_err(&espi->pdev->dev, "invalid bits per word %d\n", | |
302 | spi->bits_per_word); | |
303 | return -EINVAL; | |
304 | } | |
305 | ||
306 | chip = spi_get_ctldata(spi); | |
307 | if (!chip) { | |
308 | dev_dbg(&espi->pdev->dev, "initial setup for %s\n", | |
309 | spi->modalias); | |
310 | ||
311 | chip = kzalloc(sizeof(*chip), GFP_KERNEL); | |
312 | if (!chip) | |
313 | return -ENOMEM; | |
314 | ||
315 | chip->spi = spi; | |
316 | chip->ops = spi->controller_data; | |
317 | ||
318 | if (chip->ops && chip->ops->setup) { | |
319 | int ret = chip->ops->setup(spi); | |
320 | if (ret) { | |
321 | kfree(chip); | |
322 | return ret; | |
323 | } | |
324 | } | |
325 | ||
326 | spi_set_ctldata(spi, chip); | |
327 | } | |
328 | ||
329 | if (spi->max_speed_hz != chip->rate) { | |
330 | int err; | |
331 | ||
332 | err = ep93xx_spi_calc_divisors(espi, chip, spi->max_speed_hz); | |
333 | if (err != 0) { | |
334 | spi_set_ctldata(spi, NULL); | |
335 | kfree(chip); | |
336 | return err; | |
337 | } | |
338 | chip->rate = spi->max_speed_hz; | |
339 | } | |
340 | ||
341 | chip->dss = bits_per_word_to_dss(spi->bits_per_word); | |
342 | ||
343 | ep93xx_spi_cs_control(spi, false); | |
344 | return 0; | |
345 | } | |
346 | ||
347 | /** | |
348 | * ep93xx_spi_transfer() - queue message to be transferred | |
349 | * @spi: target SPI device | |
350 | * @msg: message to be transferred | |
351 | * | |
352 | * This function is called by SPI device drivers when they are going to transfer | |
353 | * a new message. It simply puts the message in the queue and schedules | |
354 | * workqueue to perform the actual transfer later on. | |
355 | * | |
356 | * Returns %0 on success and negative error in case of failure. | |
357 | */ | |
358 | static int ep93xx_spi_transfer(struct spi_device *spi, struct spi_message *msg) | |
359 | { | |
360 | struct ep93xx_spi *espi = spi_master_get_devdata(spi->master); | |
361 | struct spi_transfer *t; | |
362 | unsigned long flags; | |
363 | ||
364 | if (!msg || !msg->complete) | |
365 | return -EINVAL; | |
366 | ||
367 | /* first validate each transfer */ | |
368 | list_for_each_entry(t, &msg->transfers, transfer_list) { | |
369 | if (t->bits_per_word) { | |
370 | if (t->bits_per_word < 4 || t->bits_per_word > 16) | |
371 | return -EINVAL; | |
372 | } | |
373 | if (t->speed_hz && t->speed_hz < espi->min_rate) | |
374 | return -EINVAL; | |
375 | } | |
376 | ||
377 | /* | |
378 | * Now that we own the message, let's initialize it so that it is | |
379 | * suitable for us. We use @msg->status to signal whether there was | |
380 | * error in transfer and @msg->state is used to hold pointer to the | |
381 | * current transfer (or %NULL if no active current transfer). | |
382 | */ | |
383 | msg->state = NULL; | |
384 | msg->status = 0; | |
385 | msg->actual_length = 0; | |
386 | ||
387 | spin_lock_irqsave(&espi->lock, flags); | |
388 | if (!espi->running) { | |
389 | spin_unlock_irqrestore(&espi->lock, flags); | |
390 | return -ESHUTDOWN; | |
391 | } | |
392 | list_add_tail(&msg->queue, &espi->msg_queue); | |
393 | queue_work(espi->wq, &espi->msg_work); | |
394 | spin_unlock_irqrestore(&espi->lock, flags); | |
395 | ||
396 | return 0; | |
397 | } | |
398 | ||
399 | /** | |
400 | * ep93xx_spi_cleanup() - cleans up master controller specific state | |
401 | * @spi: SPI device to cleanup | |
402 | * | |
403 | * This function releases master controller specific state for given @spi | |
404 | * device. | |
405 | */ | |
406 | static void ep93xx_spi_cleanup(struct spi_device *spi) | |
407 | { | |
408 | struct ep93xx_spi_chip *chip; | |
409 | ||
410 | chip = spi_get_ctldata(spi); | |
411 | if (chip) { | |
412 | if (chip->ops && chip->ops->cleanup) | |
413 | chip->ops->cleanup(spi); | |
414 | spi_set_ctldata(spi, NULL); | |
415 | kfree(chip); | |
416 | } | |
417 | } | |
418 | ||
419 | /** | |
420 | * ep93xx_spi_chip_setup() - configures hardware according to given @chip | |
421 | * @espi: ep93xx SPI controller struct | |
422 | * @chip: chip specific settings | |
423 | * | |
424 | * This function sets up the actual hardware registers with settings given in | |
425 | * @chip. Note that no validation is done so make sure that callers validate | |
426 | * settings before calling this. | |
427 | */ | |
428 | static void ep93xx_spi_chip_setup(const struct ep93xx_spi *espi, | |
429 | const struct ep93xx_spi_chip *chip) | |
430 | { | |
431 | u16 cr0; | |
432 | ||
433 | cr0 = chip->div_scr << SSPCR0_SCR_SHIFT; | |
434 | cr0 |= (chip->spi->mode & (SPI_CPHA|SPI_CPOL)) << SSPCR0_MODE_SHIFT; | |
435 | cr0 |= chip->dss; | |
436 | ||
437 | dev_dbg(&espi->pdev->dev, "setup: mode %d, cpsr %d, scr %d, dss %d\n", | |
438 | chip->spi->mode, chip->div_cpsr, chip->div_scr, chip->dss); | |
439 | dev_dbg(&espi->pdev->dev, "setup: cr0 %#x", cr0); | |
440 | ||
441 | ep93xx_spi_write_u8(espi, SSPCPSR, chip->div_cpsr); | |
442 | ep93xx_spi_write_u16(espi, SSPCR0, cr0); | |
443 | } | |
444 | ||
445 | static inline int bits_per_word(const struct ep93xx_spi *espi) | |
446 | { | |
447 | struct spi_message *msg = espi->current_msg; | |
448 | struct spi_transfer *t = msg->state; | |
449 | ||
450 | return t->bits_per_word ? t->bits_per_word : msg->spi->bits_per_word; | |
451 | } | |
452 | ||
453 | static void ep93xx_do_write(struct ep93xx_spi *espi, struct spi_transfer *t) | |
454 | { | |
455 | if (bits_per_word(espi) > 8) { | |
456 | u16 tx_val = 0; | |
457 | ||
458 | if (t->tx_buf) | |
459 | tx_val = ((u16 *)t->tx_buf)[espi->tx]; | |
460 | ep93xx_spi_write_u16(espi, SSPDR, tx_val); | |
461 | espi->tx += sizeof(tx_val); | |
462 | } else { | |
463 | u8 tx_val = 0; | |
464 | ||
465 | if (t->tx_buf) | |
466 | tx_val = ((u8 *)t->tx_buf)[espi->tx]; | |
467 | ep93xx_spi_write_u8(espi, SSPDR, tx_val); | |
468 | espi->tx += sizeof(tx_val); | |
469 | } | |
470 | } | |
471 | ||
472 | static void ep93xx_do_read(struct ep93xx_spi *espi, struct spi_transfer *t) | |
473 | { | |
474 | if (bits_per_word(espi) > 8) { | |
475 | u16 rx_val; | |
476 | ||
477 | rx_val = ep93xx_spi_read_u16(espi, SSPDR); | |
478 | if (t->rx_buf) | |
479 | ((u16 *)t->rx_buf)[espi->rx] = rx_val; | |
480 | espi->rx += sizeof(rx_val); | |
481 | } else { | |
482 | u8 rx_val; | |
483 | ||
484 | rx_val = ep93xx_spi_read_u8(espi, SSPDR); | |
485 | if (t->rx_buf) | |
486 | ((u8 *)t->rx_buf)[espi->rx] = rx_val; | |
487 | espi->rx += sizeof(rx_val); | |
488 | } | |
489 | } | |
490 | ||
491 | /** | |
492 | * ep93xx_spi_read_write() - perform next RX/TX transfer | |
493 | * @espi: ep93xx SPI controller struct | |
494 | * | |
495 | * This function transfers next bytes (or half-words) to/from RX/TX FIFOs. If | |
496 | * called several times, the whole transfer will be completed. Returns | |
497 | * %-EINPROGRESS when current transfer was not yet completed otherwise %0. | |
498 | * | |
499 | * When this function is finished, RX FIFO should be empty and TX FIFO should be | |
500 | * full. | |
501 | */ | |
502 | static int ep93xx_spi_read_write(struct ep93xx_spi *espi) | |
503 | { | |
504 | struct spi_message *msg = espi->current_msg; | |
505 | struct spi_transfer *t = msg->state; | |
506 | ||
507 | /* read as long as RX FIFO has frames in it */ | |
508 | while ((ep93xx_spi_read_u8(espi, SSPSR) & SSPSR_RNE)) { | |
509 | ep93xx_do_read(espi, t); | |
510 | espi->fifo_level--; | |
511 | } | |
512 | ||
513 | /* write as long as TX FIFO has room */ | |
514 | while (espi->fifo_level < SPI_FIFO_SIZE && espi->tx < t->len) { | |
515 | ep93xx_do_write(espi, t); | |
516 | espi->fifo_level++; | |
517 | } | |
518 | ||
626a96db | 519 | if (espi->rx == t->len) |
011f23a3 | 520 | return 0; |
011f23a3 MW |
521 | |
522 | return -EINPROGRESS; | |
523 | } | |
524 | ||
626a96db MW |
525 | static void ep93xx_spi_pio_transfer(struct ep93xx_spi *espi) |
526 | { | |
527 | /* | |
528 | * Now everything is set up for the current transfer. We prime the TX | |
529 | * FIFO, enable interrupts, and wait for the transfer to complete. | |
530 | */ | |
531 | if (ep93xx_spi_read_write(espi)) { | |
532 | ep93xx_spi_enable_interrupts(espi); | |
533 | wait_for_completion(&espi->wait); | |
534 | } | |
535 | } | |
536 | ||
537 | /** | |
538 | * ep93xx_spi_dma_prepare() - prepares a DMA transfer | |
539 | * @espi: ep93xx SPI controller struct | |
540 | * @dir: DMA transfer direction | |
541 | * | |
542 | * Function configures the DMA, maps the buffer and prepares the DMA | |
543 | * descriptor. Returns a valid DMA descriptor in case of success and ERR_PTR | |
544 | * in case of failure. | |
545 | */ | |
546 | static struct dma_async_tx_descriptor * | |
547 | ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_data_direction dir) | |
548 | { | |
549 | struct spi_transfer *t = espi->current_msg->state; | |
550 | struct dma_async_tx_descriptor *txd; | |
551 | enum dma_slave_buswidth buswidth; | |
552 | struct dma_slave_config conf; | |
553 | struct scatterlist *sg; | |
554 | struct sg_table *sgt; | |
555 | struct dma_chan *chan; | |
556 | const void *buf, *pbuf; | |
557 | size_t len = t->len; | |
558 | int i, ret, nents; | |
559 | ||
560 | if (bits_per_word(espi) > 8) | |
561 | buswidth = DMA_SLAVE_BUSWIDTH_2_BYTES; | |
562 | else | |
563 | buswidth = DMA_SLAVE_BUSWIDTH_1_BYTE; | |
564 | ||
565 | memset(&conf, 0, sizeof(conf)); | |
566 | conf.direction = dir; | |
567 | ||
568 | if (dir == DMA_FROM_DEVICE) { | |
569 | chan = espi->dma_rx; | |
570 | buf = t->rx_buf; | |
571 | sgt = &espi->rx_sgt; | |
572 | ||
573 | conf.src_addr = espi->sspdr_phys; | |
574 | conf.src_addr_width = buswidth; | |
575 | } else { | |
576 | chan = espi->dma_tx; | |
577 | buf = t->tx_buf; | |
578 | sgt = &espi->tx_sgt; | |
579 | ||
580 | conf.dst_addr = espi->sspdr_phys; | |
581 | conf.dst_addr_width = buswidth; | |
582 | } | |
583 | ||
584 | ret = dmaengine_slave_config(chan, &conf); | |
585 | if (ret) | |
586 | return ERR_PTR(ret); | |
587 | ||
588 | /* | |
589 | * We need to split the transfer into PAGE_SIZE'd chunks. This is | |
590 | * because we are using @espi->zeropage to provide a zero RX buffer | |
591 | * for the TX transfers and we have only allocated one page for that. | |
592 | * | |
593 | * For performance reasons we allocate a new sg_table only when | |
594 | * needed. Otherwise we will re-use the current one. Eventually the | |
595 | * last sg_table is released in ep93xx_spi_release_dma(). | |
596 | */ | |
597 | ||
598 | nents = DIV_ROUND_UP(len, PAGE_SIZE); | |
599 | if (nents != sgt->nents) { | |
600 | sg_free_table(sgt); | |
601 | ||
602 | ret = sg_alloc_table(sgt, nents, GFP_KERNEL); | |
603 | if (ret) | |
604 | return ERR_PTR(ret); | |
605 | } | |
606 | ||
607 | pbuf = buf; | |
608 | for_each_sg(sgt->sgl, sg, sgt->nents, i) { | |
609 | size_t bytes = min_t(size_t, len, PAGE_SIZE); | |
610 | ||
611 | if (buf) { | |
612 | sg_set_page(sg, virt_to_page(pbuf), bytes, | |
613 | offset_in_page(pbuf)); | |
614 | } else { | |
615 | sg_set_page(sg, virt_to_page(espi->zeropage), | |
616 | bytes, 0); | |
617 | } | |
618 | ||
619 | pbuf += bytes; | |
620 | len -= bytes; | |
621 | } | |
622 | ||
623 | if (WARN_ON(len)) { | |
624 | dev_warn(&espi->pdev->dev, "len = %d expected 0!", len); | |
625 | return ERR_PTR(-EINVAL); | |
626 | } | |
627 | ||
628 | nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir); | |
629 | if (!nents) | |
630 | return ERR_PTR(-ENOMEM); | |
631 | ||
632 | txd = chan->device->device_prep_slave_sg(chan, sgt->sgl, nents, | |
633 | dir, DMA_CTRL_ACK); | |
634 | if (!txd) { | |
635 | dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir); | |
636 | return ERR_PTR(-ENOMEM); | |
637 | } | |
638 | return txd; | |
639 | } | |
640 | ||
641 | /** | |
642 | * ep93xx_spi_dma_finish() - finishes with a DMA transfer | |
643 | * @espi: ep93xx SPI controller struct | |
644 | * @dir: DMA transfer direction | |
645 | * | |
646 | * Function finishes with the DMA transfer. After this, the DMA buffer is | |
647 | * unmapped. | |
648 | */ | |
649 | static void ep93xx_spi_dma_finish(struct ep93xx_spi *espi, | |
650 | enum dma_data_direction dir) | |
651 | { | |
652 | struct dma_chan *chan; | |
653 | struct sg_table *sgt; | |
654 | ||
655 | if (dir == DMA_FROM_DEVICE) { | |
656 | chan = espi->dma_rx; | |
657 | sgt = &espi->rx_sgt; | |
658 | } else { | |
659 | chan = espi->dma_tx; | |
660 | sgt = &espi->tx_sgt; | |
661 | } | |
662 | ||
663 | dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir); | |
664 | } | |
665 | ||
666 | static void ep93xx_spi_dma_callback(void *callback_param) | |
667 | { | |
668 | complete(callback_param); | |
669 | } | |
670 | ||
671 | static void ep93xx_spi_dma_transfer(struct ep93xx_spi *espi) | |
672 | { | |
673 | struct spi_message *msg = espi->current_msg; | |
674 | struct dma_async_tx_descriptor *rxd, *txd; | |
675 | ||
676 | rxd = ep93xx_spi_dma_prepare(espi, DMA_FROM_DEVICE); | |
677 | if (IS_ERR(rxd)) { | |
678 | dev_err(&espi->pdev->dev, "DMA RX failed: %ld\n", PTR_ERR(rxd)); | |
679 | msg->status = PTR_ERR(rxd); | |
680 | return; | |
681 | } | |
682 | ||
683 | txd = ep93xx_spi_dma_prepare(espi, DMA_TO_DEVICE); | |
684 | if (IS_ERR(txd)) { | |
685 | ep93xx_spi_dma_finish(espi, DMA_FROM_DEVICE); | |
686 | dev_err(&espi->pdev->dev, "DMA TX failed: %ld\n", PTR_ERR(rxd)); | |
687 | msg->status = PTR_ERR(txd); | |
688 | return; | |
689 | } | |
690 | ||
691 | /* We are ready when RX is done */ | |
692 | rxd->callback = ep93xx_spi_dma_callback; | |
693 | rxd->callback_param = &espi->wait; | |
694 | ||
695 | /* Now submit both descriptors and wait while they finish */ | |
696 | dmaengine_submit(rxd); | |
697 | dmaengine_submit(txd); | |
698 | ||
699 | dma_async_issue_pending(espi->dma_rx); | |
700 | dma_async_issue_pending(espi->dma_tx); | |
701 | ||
702 | wait_for_completion(&espi->wait); | |
703 | ||
704 | ep93xx_spi_dma_finish(espi, DMA_TO_DEVICE); | |
705 | ep93xx_spi_dma_finish(espi, DMA_FROM_DEVICE); | |
706 | } | |
707 | ||
011f23a3 MW |
708 | /** |
709 | * ep93xx_spi_process_transfer() - processes one SPI transfer | |
710 | * @espi: ep93xx SPI controller struct | |
711 | * @msg: current message | |
712 | * @t: transfer to process | |
713 | * | |
714 | * This function processes one SPI transfer given in @t. Function waits until | |
715 | * transfer is complete (may sleep) and updates @msg->status based on whether | |
25985edc | 716 | * transfer was successfully processed or not. |
011f23a3 MW |
717 | */ |
718 | static void ep93xx_spi_process_transfer(struct ep93xx_spi *espi, | |
719 | struct spi_message *msg, | |
720 | struct spi_transfer *t) | |
721 | { | |
722 | struct ep93xx_spi_chip *chip = spi_get_ctldata(msg->spi); | |
723 | ||
724 | msg->state = t; | |
725 | ||
726 | /* | |
727 | * Handle any transfer specific settings if needed. We use | |
728 | * temporary chip settings here and restore original later when | |
729 | * the transfer is finished. | |
730 | */ | |
731 | if (t->speed_hz || t->bits_per_word) { | |
732 | struct ep93xx_spi_chip tmp_chip = *chip; | |
733 | ||
734 | if (t->speed_hz) { | |
735 | int err; | |
736 | ||
737 | err = ep93xx_spi_calc_divisors(espi, &tmp_chip, | |
738 | t->speed_hz); | |
739 | if (err) { | |
740 | dev_err(&espi->pdev->dev, | |
741 | "failed to adjust speed\n"); | |
742 | msg->status = err; | |
743 | return; | |
744 | } | |
745 | } | |
746 | ||
747 | if (t->bits_per_word) | |
748 | tmp_chip.dss = bits_per_word_to_dss(t->bits_per_word); | |
749 | ||
750 | /* | |
751 | * Set up temporary new hw settings for this transfer. | |
752 | */ | |
753 | ep93xx_spi_chip_setup(espi, &tmp_chip); | |
754 | } | |
755 | ||
756 | espi->rx = 0; | |
757 | espi->tx = 0; | |
758 | ||
759 | /* | |
626a96db MW |
760 | * There is no point of setting up DMA for the transfers which will |
761 | * fit into the FIFO and can be transferred with a single interrupt. | |
762 | * So in these cases we will be using PIO and don't bother for DMA. | |
011f23a3 | 763 | */ |
626a96db MW |
764 | if (espi->dma_rx && t->len > SPI_FIFO_SIZE) |
765 | ep93xx_spi_dma_transfer(espi); | |
766 | else | |
767 | ep93xx_spi_pio_transfer(espi); | |
011f23a3 MW |
768 | |
769 | /* | |
770 | * In case of error during transmit, we bail out from processing | |
771 | * the message. | |
772 | */ | |
773 | if (msg->status) | |
774 | return; | |
775 | ||
626a96db MW |
776 | msg->actual_length += t->len; |
777 | ||
011f23a3 MW |
778 | /* |
779 | * After this transfer is finished, perform any possible | |
780 | * post-transfer actions requested by the protocol driver. | |
781 | */ | |
782 | if (t->delay_usecs) { | |
783 | set_current_state(TASK_UNINTERRUPTIBLE); | |
784 | schedule_timeout(usecs_to_jiffies(t->delay_usecs)); | |
785 | } | |
786 | if (t->cs_change) { | |
787 | if (!list_is_last(&t->transfer_list, &msg->transfers)) { | |
788 | /* | |
789 | * In case protocol driver is asking us to drop the | |
790 | * chipselect briefly, we let the scheduler to handle | |
791 | * any "delay" here. | |
792 | */ | |
793 | ep93xx_spi_cs_control(msg->spi, false); | |
794 | cond_resched(); | |
795 | ep93xx_spi_cs_control(msg->spi, true); | |
796 | } | |
797 | } | |
798 | ||
799 | if (t->speed_hz || t->bits_per_word) | |
800 | ep93xx_spi_chip_setup(espi, chip); | |
801 | } | |
802 | ||
803 | /* | |
804 | * ep93xx_spi_process_message() - process one SPI message | |
805 | * @espi: ep93xx SPI controller struct | |
806 | * @msg: message to process | |
807 | * | |
808 | * This function processes a single SPI message. We go through all transfers in | |
809 | * the message and pass them to ep93xx_spi_process_transfer(). Chipselect is | |
810 | * asserted during the whole message (unless per transfer cs_change is set). | |
811 | * | |
812 | * @msg->status contains %0 in case of success or negative error code in case of | |
813 | * failure. | |
814 | */ | |
815 | static void ep93xx_spi_process_message(struct ep93xx_spi *espi, | |
816 | struct spi_message *msg) | |
817 | { | |
818 | unsigned long timeout; | |
819 | struct spi_transfer *t; | |
820 | int err; | |
821 | ||
822 | /* | |
823 | * Enable the SPI controller and its clock. | |
824 | */ | |
825 | err = ep93xx_spi_enable(espi); | |
826 | if (err) { | |
827 | dev_err(&espi->pdev->dev, "failed to enable SPI controller\n"); | |
828 | msg->status = err; | |
829 | return; | |
830 | } | |
831 | ||
832 | /* | |
833 | * Just to be sure: flush any data from RX FIFO. | |
834 | */ | |
835 | timeout = jiffies + msecs_to_jiffies(SPI_TIMEOUT); | |
836 | while (ep93xx_spi_read_u16(espi, SSPSR) & SSPSR_RNE) { | |
837 | if (time_after(jiffies, timeout)) { | |
838 | dev_warn(&espi->pdev->dev, | |
839 | "timeout while flushing RX FIFO\n"); | |
840 | msg->status = -ETIMEDOUT; | |
841 | return; | |
842 | } | |
843 | ep93xx_spi_read_u16(espi, SSPDR); | |
844 | } | |
845 | ||
846 | /* | |
847 | * We explicitly handle FIFO level. This way we don't have to check TX | |
848 | * FIFO status using %SSPSR_TNF bit which may cause RX FIFO overruns. | |
849 | */ | |
850 | espi->fifo_level = 0; | |
851 | ||
852 | /* | |
853 | * Update SPI controller registers according to spi device and assert | |
854 | * the chipselect. | |
855 | */ | |
856 | ep93xx_spi_chip_setup(espi, spi_get_ctldata(msg->spi)); | |
857 | ep93xx_spi_cs_control(msg->spi, true); | |
858 | ||
859 | list_for_each_entry(t, &msg->transfers, transfer_list) { | |
860 | ep93xx_spi_process_transfer(espi, msg, t); | |
861 | if (msg->status) | |
862 | break; | |
863 | } | |
864 | ||
865 | /* | |
866 | * Now the whole message is transferred (or failed for some reason). We | |
867 | * deselect the device and disable the SPI controller. | |
868 | */ | |
869 | ep93xx_spi_cs_control(msg->spi, false); | |
870 | ep93xx_spi_disable(espi); | |
871 | } | |
872 | ||
873 | #define work_to_espi(work) (container_of((work), struct ep93xx_spi, msg_work)) | |
874 | ||
875 | /** | |
876 | * ep93xx_spi_work() - EP93xx SPI workqueue worker function | |
877 | * @work: work struct | |
878 | * | |
879 | * Workqueue worker function. This function is called when there are new | |
880 | * SPI messages to be processed. Message is taken out from the queue and then | |
881 | * passed to ep93xx_spi_process_message(). | |
882 | * | |
883 | * After message is transferred, protocol driver is notified by calling | |
884 | * @msg->complete(). In case of error, @msg->status is set to negative error | |
885 | * number, otherwise it contains zero (and @msg->actual_length is updated). | |
886 | */ | |
887 | static void ep93xx_spi_work(struct work_struct *work) | |
888 | { | |
889 | struct ep93xx_spi *espi = work_to_espi(work); | |
890 | struct spi_message *msg; | |
891 | ||
892 | spin_lock_irq(&espi->lock); | |
893 | if (!espi->running || espi->current_msg || | |
894 | list_empty(&espi->msg_queue)) { | |
895 | spin_unlock_irq(&espi->lock); | |
896 | return; | |
897 | } | |
898 | msg = list_first_entry(&espi->msg_queue, struct spi_message, queue); | |
899 | list_del_init(&msg->queue); | |
900 | espi->current_msg = msg; | |
901 | spin_unlock_irq(&espi->lock); | |
902 | ||
903 | ep93xx_spi_process_message(espi, msg); | |
904 | ||
905 | /* | |
906 | * Update the current message and re-schedule ourselves if there are | |
907 | * more messages in the queue. | |
908 | */ | |
909 | spin_lock_irq(&espi->lock); | |
910 | espi->current_msg = NULL; | |
911 | if (espi->running && !list_empty(&espi->msg_queue)) | |
912 | queue_work(espi->wq, &espi->msg_work); | |
913 | spin_unlock_irq(&espi->lock); | |
914 | ||
915 | /* notify the protocol driver that we are done with this message */ | |
916 | msg->complete(msg->context); | |
917 | } | |
918 | ||
919 | static irqreturn_t ep93xx_spi_interrupt(int irq, void *dev_id) | |
920 | { | |
921 | struct ep93xx_spi *espi = dev_id; | |
922 | u8 irq_status = ep93xx_spi_read_u8(espi, SSPIIR); | |
923 | ||
924 | /* | |
925 | * If we got ROR (receive overrun) interrupt we know that something is | |
926 | * wrong. Just abort the message. | |
927 | */ | |
928 | if (unlikely(irq_status & SSPIIR_RORIS)) { | |
929 | /* clear the overrun interrupt */ | |
930 | ep93xx_spi_write_u8(espi, SSPICR, 0); | |
931 | dev_warn(&espi->pdev->dev, | |
932 | "receive overrun, aborting the message\n"); | |
933 | espi->current_msg->status = -EIO; | |
934 | } else { | |
935 | /* | |
936 | * Interrupt is either RX (RIS) or TX (TIS). For both cases we | |
937 | * simply execute next data transfer. | |
938 | */ | |
939 | if (ep93xx_spi_read_write(espi)) { | |
940 | /* | |
941 | * In normal case, there still is some processing left | |
942 | * for current transfer. Let's wait for the next | |
943 | * interrupt then. | |
944 | */ | |
945 | return IRQ_HANDLED; | |
946 | } | |
947 | } | |
948 | ||
949 | /* | |
950 | * Current transfer is finished, either with error or with success. In | |
951 | * any case we disable interrupts and notify the worker to handle | |
952 | * any post-processing of the message. | |
953 | */ | |
954 | ep93xx_spi_disable_interrupts(espi); | |
955 | complete(&espi->wait); | |
956 | return IRQ_HANDLED; | |
957 | } | |
958 | ||
626a96db MW |
959 | static bool ep93xx_spi_dma_filter(struct dma_chan *chan, void *filter_param) |
960 | { | |
961 | if (ep93xx_dma_chan_is_m2p(chan)) | |
962 | return false; | |
963 | ||
964 | chan->private = filter_param; | |
965 | return true; | |
966 | } | |
967 | ||
968 | static int ep93xx_spi_setup_dma(struct ep93xx_spi *espi) | |
969 | { | |
970 | dma_cap_mask_t mask; | |
971 | int ret; | |
972 | ||
973 | espi->zeropage = (void *)get_zeroed_page(GFP_KERNEL); | |
974 | if (!espi->zeropage) | |
975 | return -ENOMEM; | |
976 | ||
977 | dma_cap_zero(mask); | |
978 | dma_cap_set(DMA_SLAVE, mask); | |
979 | ||
980 | espi->dma_rx_data.port = EP93XX_DMA_SSP; | |
981 | espi->dma_rx_data.direction = DMA_FROM_DEVICE; | |
982 | espi->dma_rx_data.name = "ep93xx-spi-rx"; | |
983 | ||
984 | espi->dma_rx = dma_request_channel(mask, ep93xx_spi_dma_filter, | |
985 | &espi->dma_rx_data); | |
986 | if (!espi->dma_rx) { | |
987 | ret = -ENODEV; | |
988 | goto fail_free_page; | |
989 | } | |
990 | ||
991 | espi->dma_tx_data.port = EP93XX_DMA_SSP; | |
992 | espi->dma_tx_data.direction = DMA_TO_DEVICE; | |
993 | espi->dma_tx_data.name = "ep93xx-spi-tx"; | |
994 | ||
995 | espi->dma_tx = dma_request_channel(mask, ep93xx_spi_dma_filter, | |
996 | &espi->dma_tx_data); | |
997 | if (!espi->dma_tx) { | |
998 | ret = -ENODEV; | |
999 | goto fail_release_rx; | |
1000 | } | |
1001 | ||
1002 | return 0; | |
1003 | ||
1004 | fail_release_rx: | |
1005 | dma_release_channel(espi->dma_rx); | |
1006 | espi->dma_rx = NULL; | |
1007 | fail_free_page: | |
1008 | free_page((unsigned long)espi->zeropage); | |
1009 | ||
1010 | return ret; | |
1011 | } | |
1012 | ||
1013 | static void ep93xx_spi_release_dma(struct ep93xx_spi *espi) | |
1014 | { | |
1015 | if (espi->dma_rx) { | |
1016 | dma_release_channel(espi->dma_rx); | |
1017 | sg_free_table(&espi->rx_sgt); | |
1018 | } | |
1019 | if (espi->dma_tx) { | |
1020 | dma_release_channel(espi->dma_tx); | |
1021 | sg_free_table(&espi->tx_sgt); | |
1022 | } | |
1023 | ||
1024 | if (espi->zeropage) | |
1025 | free_page((unsigned long)espi->zeropage); | |
1026 | } | |
1027 | ||
011f23a3 MW |
1028 | static int __init ep93xx_spi_probe(struct platform_device *pdev) |
1029 | { | |
1030 | struct spi_master *master; | |
1031 | struct ep93xx_spi_info *info; | |
1032 | struct ep93xx_spi *espi; | |
1033 | struct resource *res; | |
1034 | int error; | |
1035 | ||
1036 | info = pdev->dev.platform_data; | |
1037 | ||
1038 | master = spi_alloc_master(&pdev->dev, sizeof(*espi)); | |
1039 | if (!master) { | |
1040 | dev_err(&pdev->dev, "failed to allocate spi master\n"); | |
1041 | return -ENOMEM; | |
1042 | } | |
1043 | ||
1044 | master->setup = ep93xx_spi_setup; | |
1045 | master->transfer = ep93xx_spi_transfer; | |
1046 | master->cleanup = ep93xx_spi_cleanup; | |
1047 | master->bus_num = pdev->id; | |
1048 | master->num_chipselect = info->num_chipselect; | |
1049 | master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; | |
1050 | ||
1051 | platform_set_drvdata(pdev, master); | |
1052 | ||
1053 | espi = spi_master_get_devdata(master); | |
1054 | ||
1055 | espi->clk = clk_get(&pdev->dev, NULL); | |
1056 | if (IS_ERR(espi->clk)) { | |
1057 | dev_err(&pdev->dev, "unable to get spi clock\n"); | |
1058 | error = PTR_ERR(espi->clk); | |
1059 | goto fail_release_master; | |
1060 | } | |
1061 | ||
1062 | spin_lock_init(&espi->lock); | |
1063 | init_completion(&espi->wait); | |
1064 | ||
1065 | /* | |
1066 | * Calculate maximum and minimum supported clock rates | |
1067 | * for the controller. | |
1068 | */ | |
1069 | espi->max_rate = clk_get_rate(espi->clk) / 2; | |
1070 | espi->min_rate = clk_get_rate(espi->clk) / (254 * 256); | |
1071 | espi->pdev = pdev; | |
1072 | ||
1073 | espi->irq = platform_get_irq(pdev, 0); | |
1074 | if (espi->irq < 0) { | |
1075 | error = -EBUSY; | |
1076 | dev_err(&pdev->dev, "failed to get irq resources\n"); | |
1077 | goto fail_put_clock; | |
1078 | } | |
1079 | ||
1080 | res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
1081 | if (!res) { | |
1082 | dev_err(&pdev->dev, "unable to get iomem resource\n"); | |
1083 | error = -ENODEV; | |
1084 | goto fail_put_clock; | |
1085 | } | |
1086 | ||
1087 | res = request_mem_region(res->start, resource_size(res), pdev->name); | |
1088 | if (!res) { | |
1089 | dev_err(&pdev->dev, "unable to request iomem resources\n"); | |
1090 | error = -EBUSY; | |
1091 | goto fail_put_clock; | |
1092 | } | |
1093 | ||
626a96db | 1094 | espi->sspdr_phys = res->start + SSPDR; |
011f23a3 MW |
1095 | espi->regs_base = ioremap(res->start, resource_size(res)); |
1096 | if (!espi->regs_base) { | |
1097 | dev_err(&pdev->dev, "failed to map resources\n"); | |
1098 | error = -ENODEV; | |
1099 | goto fail_free_mem; | |
1100 | } | |
1101 | ||
1102 | error = request_irq(espi->irq, ep93xx_spi_interrupt, 0, | |
1103 | "ep93xx-spi", espi); | |
1104 | if (error) { | |
1105 | dev_err(&pdev->dev, "failed to request irq\n"); | |
1106 | goto fail_unmap_regs; | |
1107 | } | |
1108 | ||
626a96db MW |
1109 | if (info->use_dma && ep93xx_spi_setup_dma(espi)) |
1110 | dev_warn(&pdev->dev, "DMA setup failed. Falling back to PIO\n"); | |
1111 | ||
011f23a3 MW |
1112 | espi->wq = create_singlethread_workqueue("ep93xx_spid"); |
1113 | if (!espi->wq) { | |
1114 | dev_err(&pdev->dev, "unable to create workqueue\n"); | |
626a96db | 1115 | goto fail_free_dma; |
011f23a3 MW |
1116 | } |
1117 | INIT_WORK(&espi->msg_work, ep93xx_spi_work); | |
1118 | INIT_LIST_HEAD(&espi->msg_queue); | |
1119 | espi->running = true; | |
1120 | ||
1121 | /* make sure that the hardware is disabled */ | |
1122 | ep93xx_spi_write_u8(espi, SSPCR1, 0); | |
1123 | ||
1124 | error = spi_register_master(master); | |
1125 | if (error) { | |
1126 | dev_err(&pdev->dev, "failed to register SPI master\n"); | |
1127 | goto fail_free_queue; | |
1128 | } | |
1129 | ||
1130 | dev_info(&pdev->dev, "EP93xx SPI Controller at 0x%08lx irq %d\n", | |
1131 | (unsigned long)res->start, espi->irq); | |
1132 | ||
1133 | return 0; | |
1134 | ||
1135 | fail_free_queue: | |
1136 | destroy_workqueue(espi->wq); | |
626a96db MW |
1137 | fail_free_dma: |
1138 | ep93xx_spi_release_dma(espi); | |
011f23a3 MW |
1139 | free_irq(espi->irq, espi); |
1140 | fail_unmap_regs: | |
1141 | iounmap(espi->regs_base); | |
1142 | fail_free_mem: | |
1143 | release_mem_region(res->start, resource_size(res)); | |
1144 | fail_put_clock: | |
1145 | clk_put(espi->clk); | |
1146 | fail_release_master: | |
1147 | spi_master_put(master); | |
1148 | platform_set_drvdata(pdev, NULL); | |
1149 | ||
1150 | return error; | |
1151 | } | |
1152 | ||
1153 | static int __exit ep93xx_spi_remove(struct platform_device *pdev) | |
1154 | { | |
1155 | struct spi_master *master = platform_get_drvdata(pdev); | |
1156 | struct ep93xx_spi *espi = spi_master_get_devdata(master); | |
1157 | struct resource *res; | |
1158 | ||
1159 | spin_lock_irq(&espi->lock); | |
1160 | espi->running = false; | |
1161 | spin_unlock_irq(&espi->lock); | |
1162 | ||
1163 | destroy_workqueue(espi->wq); | |
1164 | ||
1165 | /* | |
1166 | * Complete remaining messages with %-ESHUTDOWN status. | |
1167 | */ | |
1168 | spin_lock_irq(&espi->lock); | |
1169 | while (!list_empty(&espi->msg_queue)) { | |
1170 | struct spi_message *msg; | |
1171 | ||
1172 | msg = list_first_entry(&espi->msg_queue, | |
1173 | struct spi_message, queue); | |
1174 | list_del_init(&msg->queue); | |
1175 | msg->status = -ESHUTDOWN; | |
1176 | spin_unlock_irq(&espi->lock); | |
1177 | msg->complete(msg->context); | |
1178 | spin_lock_irq(&espi->lock); | |
1179 | } | |
1180 | spin_unlock_irq(&espi->lock); | |
1181 | ||
626a96db | 1182 | ep93xx_spi_release_dma(espi); |
011f23a3 MW |
1183 | free_irq(espi->irq, espi); |
1184 | iounmap(espi->regs_base); | |
1185 | res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
1186 | release_mem_region(res->start, resource_size(res)); | |
1187 | clk_put(espi->clk); | |
1188 | platform_set_drvdata(pdev, NULL); | |
1189 | ||
1190 | spi_unregister_master(master); | |
1191 | return 0; | |
1192 | } | |
1193 | ||
1194 | static struct platform_driver ep93xx_spi_driver = { | |
1195 | .driver = { | |
1196 | .name = "ep93xx-spi", | |
1197 | .owner = THIS_MODULE, | |
1198 | }, | |
1199 | .remove = __exit_p(ep93xx_spi_remove), | |
1200 | }; | |
1201 | ||
1202 | static int __init ep93xx_spi_init(void) | |
1203 | { | |
1204 | return platform_driver_probe(&ep93xx_spi_driver, ep93xx_spi_probe); | |
1205 | } | |
1206 | module_init(ep93xx_spi_init); | |
1207 | ||
1208 | static void __exit ep93xx_spi_exit(void) | |
1209 | { | |
1210 | platform_driver_unregister(&ep93xx_spi_driver); | |
1211 | } | |
1212 | module_exit(ep93xx_spi_exit); | |
1213 | ||
1214 | MODULE_DESCRIPTION("EP93xx SPI Controller driver"); | |
1215 | MODULE_AUTHOR("Mika Westerberg <mika.westerberg@iki.fi>"); | |
1216 | MODULE_LICENSE("GPL"); | |
1217 | MODULE_ALIAS("platform:ep93xx-spi"); |