Commit | Line | Data |
---|---|---|
1da177e4 | 1 | /* |
1da177e4 LT |
2 | * Serial driver for the amiga builtin port. |
3 | * | |
4 | * This code was created by taking serial.c version 4.30 from kernel | |
5 | * release 2.3.22, replacing all hardware related stuff with the | |
6 | * corresponding amiga hardware actions, and removing all irrelevant | |
7 | * code. As a consequence, it uses many of the constants and names | |
8 | * associated with the registers and bits of 16550 compatible UARTS - | |
9 | * but only to keep track of status, etc in the state variables. It | |
10 | * was done this was to make it easier to keep the code in line with | |
11 | * (non hardware specific) changes to serial.c. | |
12 | * | |
13 | * The port is registered with the tty driver as minor device 64, and | |
14 | * therefore other ports should should only use 65 upwards. | |
15 | * | |
16 | * Richard Lucock 28/12/99 | |
17 | * | |
18 | * Copyright (C) 1991, 1992 Linus Torvalds | |
19 | * Copyright (C) 1992, 1993, 1994, 1995, 1996, 1997, | |
20 | * 1998, 1999 Theodore Ts'o | |
21 | * | |
22 | */ | |
23 | ||
24 | /* | |
25 | * Serial driver configuration section. Here are the various options: | |
26 | * | |
27 | * SERIAL_PARANOIA_CHECK | |
28 | * Check the magic number for the async_structure where | |
29 | * ever possible. | |
30 | */ | |
31 | ||
1da177e4 LT |
32 | #include <linux/delay.h> |
33 | ||
34 | #undef SERIAL_PARANOIA_CHECK | |
1da177e4 LT |
35 | |
36 | /* Set of debugging defines */ | |
37 | ||
38 | #undef SERIAL_DEBUG_INTR | |
39 | #undef SERIAL_DEBUG_OPEN | |
40 | #undef SERIAL_DEBUG_FLOW | |
41 | #undef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT | |
42 | ||
43 | /* Sanity checks */ | |
44 | ||
1da177e4 LT |
45 | #if defined(MODULE) && defined(SERIAL_DEBUG_MCOUNT) |
46 | #define DBG_CNT(s) printk("(%s): [%x] refc=%d, serc=%d, ttyc=%d -> %s\n", \ | |
01bd730d | 47 | tty->name, (info->tport.flags), serial_driver->refcount,info->count,tty->count,s) |
1da177e4 LT |
48 | #else |
49 | #define DBG_CNT(s) | |
50 | #endif | |
51 | ||
52 | /* | |
53 | * End of serial driver configuration section. | |
54 | */ | |
55 | ||
56 | #include <linux/module.h> | |
57 | ||
58 | #include <linux/types.h> | |
59 | #include <linux/serial.h> | |
1da177e4 LT |
60 | #include <linux/serial_reg.h> |
61 | static char *serial_version = "4.30"; | |
62 | ||
63 | #include <linux/errno.h> | |
64 | #include <linux/signal.h> | |
65 | #include <linux/sched.h> | |
66 | #include <linux/kernel.h> | |
67 | #include <linux/timer.h> | |
68 | #include <linux/interrupt.h> | |
69 | #include <linux/tty.h> | |
70 | #include <linux/tty_flip.h> | |
6fe18d26 | 71 | #include <linux/circ_buf.h> |
1da177e4 LT |
72 | #include <linux/console.h> |
73 | #include <linux/major.h> | |
74 | #include <linux/string.h> | |
75 | #include <linux/fcntl.h> | |
76 | #include <linux/ptrace.h> | |
77 | #include <linux/ioport.h> | |
78 | #include <linux/mm.h> | |
d594027d | 79 | #include <linux/seq_file.h> |
1da177e4 LT |
80 | #include <linux/slab.h> |
81 | #include <linux/init.h> | |
82 | #include <linux/bitops.h> | |
826e8c8c | 83 | #include <linux/platform_device.h> |
1da177e4 LT |
84 | |
85 | #include <asm/setup.h> | |
86 | ||
1da177e4 LT |
87 | |
88 | #include <asm/irq.h> | |
89 | ||
90 | #include <asm/amigahw.h> | |
91 | #include <asm/amigaints.h> | |
92 | ||
6fe18d26 JS |
93 | struct serial_state { |
94 | struct tty_port tport; | |
95 | struct circ_buf xmit; | |
96 | struct async_icount icount; | |
97 | ||
98 | unsigned long port; | |
99 | int baud_base; | |
100 | int xmit_fifo_size; | |
101 | int custom_divisor; | |
102 | int read_status_mask; | |
103 | int ignore_status_mask; | |
104 | int timeout; | |
105 | int quot; | |
106 | int IER; /* Interrupt Enable Register */ | |
107 | int MCR; /* Modem control register */ | |
108 | int x_char; /* xon/xoff character */ | |
109 | }; | |
110 | ||
b4290a23 | 111 | #define custom amiga_custom |
1da177e4 LT |
112 | static char *serial_name = "Amiga-builtin serial driver"; |
113 | ||
114 | static struct tty_driver *serial_driver; | |
115 | ||
116 | /* number of characters left in xmit buffer before we ask for more */ | |
117 | #define WAKEUP_CHARS 256 | |
118 | ||
1da177e4 LT |
119 | static unsigned char current_ctl_bits; |
120 | ||
588993dd JS |
121 | static void change_speed(struct tty_struct *tty, struct serial_state *info, |
122 | struct ktermios *old); | |
1da177e4 LT |
123 | static void rs_wait_until_sent(struct tty_struct *tty, int timeout); |
124 | ||
125 | ||
126 | static struct serial_state rs_table[1]; | |
127 | ||
fe971071 | 128 | #define NR_PORTS ARRAY_SIZE(rs_table) |
1da177e4 | 129 | |
1da177e4 LT |
130 | #include <asm/uaccess.h> |
131 | ||
132 | #define serial_isroot() (capable(CAP_SYS_ADMIN)) | |
133 | ||
134 | ||
916b7656 | 135 | static inline int serial_paranoia_check(struct serial_state *info, |
1da177e4 LT |
136 | char *name, const char *routine) |
137 | { | |
138 | #ifdef SERIAL_PARANOIA_CHECK | |
139 | static const char *badmagic = | |
140 | "Warning: bad magic number for serial struct (%s) in %s\n"; | |
141 | static const char *badinfo = | |
142 | "Warning: null async_struct for (%s) in %s\n"; | |
143 | ||
144 | if (!info) { | |
145 | printk(badinfo, name, routine); | |
146 | return 1; | |
147 | } | |
148 | if (info->magic != SERIAL_MAGIC) { | |
149 | printk(badmagic, name, routine); | |
150 | return 1; | |
151 | } | |
152 | #endif | |
153 | return 0; | |
154 | } | |
155 | ||
156 | /* some serial hardware definitions */ | |
157 | #define SDR_OVRUN (1<<15) | |
158 | #define SDR_RBF (1<<14) | |
159 | #define SDR_TBE (1<<13) | |
160 | #define SDR_TSRE (1<<12) | |
161 | ||
162 | #define SERPER_PARENB (1<<15) | |
163 | ||
164 | #define AC_SETCLR (1<<15) | |
165 | #define AC_UARTBRK (1<<11) | |
166 | ||
167 | #define SER_DTR (1<<7) | |
168 | #define SER_RTS (1<<6) | |
169 | #define SER_DCD (1<<5) | |
170 | #define SER_CTS (1<<4) | |
171 | #define SER_DSR (1<<3) | |
172 | ||
173 | static __inline__ void rtsdtr_ctrl(int bits) | |
174 | { | |
175 | ciab.pra = ((bits & (SER_RTS | SER_DTR)) ^ (SER_RTS | SER_DTR)) | (ciab.pra & ~(SER_RTS | SER_DTR)); | |
176 | } | |
177 | ||
178 | /* | |
179 | * ------------------------------------------------------------ | |
180 | * rs_stop() and rs_start() | |
181 | * | |
182 | * This routines are called before setting or resetting tty->stopped. | |
183 | * They enable or disable transmitter interrupts, as necessary. | |
184 | * ------------------------------------------------------------ | |
185 | */ | |
186 | static void rs_stop(struct tty_struct *tty) | |
187 | { | |
916b7656 | 188 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
189 | unsigned long flags; |
190 | ||
191 | if (serial_paranoia_check(info, tty->name, "rs_stop")) | |
192 | return; | |
193 | ||
194 | local_irq_save(flags); | |
195 | if (info->IER & UART_IER_THRI) { | |
196 | info->IER &= ~UART_IER_THRI; | |
197 | /* disable Tx interrupt and remove any pending interrupts */ | |
198 | custom.intena = IF_TBE; | |
199 | mb(); | |
200 | custom.intreq = IF_TBE; | |
201 | mb(); | |
202 | } | |
203 | local_irq_restore(flags); | |
204 | } | |
205 | ||
206 | static void rs_start(struct tty_struct *tty) | |
207 | { | |
916b7656 | 208 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
209 | unsigned long flags; |
210 | ||
211 | if (serial_paranoia_check(info, tty->name, "rs_start")) | |
212 | return; | |
213 | ||
214 | local_irq_save(flags); | |
215 | if (info->xmit.head != info->xmit.tail | |
216 | && info->xmit.buf | |
217 | && !(info->IER & UART_IER_THRI)) { | |
218 | info->IER |= UART_IER_THRI; | |
219 | custom.intena = IF_SETCLR | IF_TBE; | |
220 | mb(); | |
221 | /* set a pending Tx Interrupt, transmitter should restart now */ | |
222 | custom.intreq = IF_SETCLR | IF_TBE; | |
223 | mb(); | |
224 | } | |
225 | local_irq_restore(flags); | |
226 | } | |
227 | ||
228 | /* | |
229 | * ---------------------------------------------------------------------- | |
230 | * | |
231 | * Here starts the interrupt handling routines. All of the following | |
232 | * subroutines are declared as inline and are folded into | |
233 | * rs_interrupt(). They were separated out for readability's sake. | |
234 | * | |
235 | * Note: rs_interrupt() is a "fast" interrupt, which means that it | |
236 | * runs with interrupts turned off. People who may want to modify | |
237 | * rs_interrupt() should try to keep the interrupt handler as fast as | |
238 | * possible. After you are done making modifications, it is not a bad | |
239 | * idea to do: | |
240 | * | |
241 | * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c | |
242 | * | |
243 | * and look at the resulting assemble code in serial.s. | |
244 | * | |
245 | * - Ted Ts'o (tytso@mit.edu), 7-Mar-93 | |
246 | * ----------------------------------------------------------------------- | |
247 | */ | |
248 | ||
916b7656 | 249 | static void receive_chars(struct serial_state *info) |
1da177e4 LT |
250 | { |
251 | int status; | |
252 | int serdatr; | |
33f0f88f | 253 | unsigned char ch, flag; |
1da177e4 | 254 | struct async_icount *icount; |
33f0f88f | 255 | int oe = 0; |
1da177e4 | 256 | |
916b7656 | 257 | icount = &info->icount; |
1da177e4 LT |
258 | |
259 | status = UART_LSR_DR; /* We obviously have a character! */ | |
260 | serdatr = custom.serdatr; | |
261 | mb(); | |
262 | custom.intreq = IF_RBF; | |
263 | mb(); | |
264 | ||
265 | if((serdatr & 0x1ff) == 0) | |
266 | status |= UART_LSR_BI; | |
267 | if(serdatr & SDR_OVRUN) | |
268 | status |= UART_LSR_OE; | |
269 | ||
270 | ch = serdatr & 0xff; | |
1da177e4 LT |
271 | icount->rx++; |
272 | ||
273 | #ifdef SERIAL_DEBUG_INTR | |
274 | printk("DR%02x:%02x...", ch, status); | |
275 | #endif | |
33f0f88f | 276 | flag = TTY_NORMAL; |
1da177e4 LT |
277 | |
278 | /* | |
279 | * We don't handle parity or frame errors - but I have left | |
280 | * the code in, since I'm not sure that the errors can't be | |
281 | * detected. | |
282 | */ | |
283 | ||
284 | if (status & (UART_LSR_BI | UART_LSR_PE | | |
285 | UART_LSR_FE | UART_LSR_OE)) { | |
286 | /* | |
287 | * For statistics only | |
288 | */ | |
289 | if (status & UART_LSR_BI) { | |
290 | status &= ~(UART_LSR_FE | UART_LSR_PE); | |
291 | icount->brk++; | |
292 | } else if (status & UART_LSR_PE) | |
293 | icount->parity++; | |
294 | else if (status & UART_LSR_FE) | |
295 | icount->frame++; | |
296 | if (status & UART_LSR_OE) | |
297 | icount->overrun++; | |
298 | ||
299 | /* | |
300 | * Now check to see if character should be | |
301 | * ignored, and mask off conditions which | |
302 | * should be ignored. | |
303 | */ | |
304 | if (status & info->ignore_status_mask) | |
33f0f88f | 305 | goto out; |
1da177e4 LT |
306 | |
307 | status &= info->read_status_mask; | |
308 | ||
309 | if (status & (UART_LSR_BI)) { | |
310 | #ifdef SERIAL_DEBUG_INTR | |
311 | printk("handling break...."); | |
312 | #endif | |
33f0f88f | 313 | flag = TTY_BREAK; |
01bd730d | 314 | if (info->tport.flags & ASYNC_SAK) |
2e124b4a | 315 | do_SAK(info->tport.tty); |
1da177e4 | 316 | } else if (status & UART_LSR_PE) |
33f0f88f | 317 | flag = TTY_PARITY; |
1da177e4 | 318 | else if (status & UART_LSR_FE) |
33f0f88f | 319 | flag = TTY_FRAME; |
1da177e4 LT |
320 | if (status & UART_LSR_OE) { |
321 | /* | |
322 | * Overrun is special, since it's | |
323 | * reported immediately, and doesn't | |
324 | * affect the current character | |
325 | */ | |
33f0f88f | 326 | oe = 1; |
1da177e4 LT |
327 | } |
328 | } | |
92a19f9c | 329 | tty_insert_flip_char(&info->tport, ch, flag); |
33f0f88f | 330 | if (oe == 1) |
92a19f9c | 331 | tty_insert_flip_char(&info->tport, 0, TTY_OVERRUN); |
2e124b4a | 332 | tty_flip_buffer_push(&info->tport); |
33f0f88f AC |
333 | out: |
334 | return; | |
1da177e4 LT |
335 | } |
336 | ||
916b7656 | 337 | static void transmit_chars(struct serial_state *info) |
1da177e4 LT |
338 | { |
339 | custom.intreq = IF_TBE; | |
340 | mb(); | |
341 | if (info->x_char) { | |
342 | custom.serdat = info->x_char | 0x100; | |
343 | mb(); | |
916b7656 | 344 | info->icount.tx++; |
1da177e4 LT |
345 | info->x_char = 0; |
346 | return; | |
347 | } | |
348 | if (info->xmit.head == info->xmit.tail | |
87758791 JS |
349 | || info->tport.tty->stopped |
350 | || info->tport.tty->hw_stopped) { | |
1da177e4 LT |
351 | info->IER &= ~UART_IER_THRI; |
352 | custom.intena = IF_TBE; | |
353 | mb(); | |
354 | return; | |
355 | } | |
356 | ||
357 | custom.serdat = info->xmit.buf[info->xmit.tail++] | 0x100; | |
358 | mb(); | |
359 | info->xmit.tail = info->xmit.tail & (SERIAL_XMIT_SIZE-1); | |
916b7656 | 360 | info->icount.tx++; |
1da177e4 LT |
361 | |
362 | if (CIRC_CNT(info->xmit.head, | |
363 | info->xmit.tail, | |
364 | SERIAL_XMIT_SIZE) < WAKEUP_CHARS) | |
87758791 | 365 | tty_wakeup(info->tport.tty); |
1da177e4 LT |
366 | |
367 | #ifdef SERIAL_DEBUG_INTR | |
368 | printk("THRE..."); | |
369 | #endif | |
370 | if (info->xmit.head == info->xmit.tail) { | |
371 | custom.intena = IF_TBE; | |
372 | mb(); | |
373 | info->IER &= ~UART_IER_THRI; | |
374 | } | |
375 | } | |
376 | ||
916b7656 | 377 | static void check_modem_status(struct serial_state *info) |
1da177e4 | 378 | { |
7188dc20 | 379 | struct tty_port *port = &info->tport; |
1da177e4 LT |
380 | unsigned char status = ciab.pra & (SER_DCD | SER_CTS | SER_DSR); |
381 | unsigned char dstatus; | |
382 | struct async_icount *icount; | |
383 | ||
384 | /* Determine bits that have changed */ | |
385 | dstatus = status ^ current_ctl_bits; | |
386 | current_ctl_bits = status; | |
387 | ||
388 | if (dstatus) { | |
916b7656 | 389 | icount = &info->icount; |
1da177e4 LT |
390 | /* update input line counters */ |
391 | if (dstatus & SER_DSR) | |
392 | icount->dsr++; | |
393 | if (dstatus & SER_DCD) { | |
394 | icount->dcd++; | |
1da177e4 LT |
395 | } |
396 | if (dstatus & SER_CTS) | |
397 | icount->cts++; | |
7188dc20 | 398 | wake_up_interruptible(&port->delta_msr_wait); |
1da177e4 LT |
399 | } |
400 | ||
7188dc20 | 401 | if ((port->flags & ASYNC_CHECK_CD) && (dstatus & SER_DCD)) { |
1da177e4 LT |
402 | #if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR)) |
403 | printk("ttyS%d CD now %s...", info->line, | |
404 | (!(status & SER_DCD)) ? "on" : "off"); | |
405 | #endif | |
406 | if (!(status & SER_DCD)) | |
7188dc20 | 407 | wake_up_interruptible(&port->open_wait); |
1da177e4 LT |
408 | else { |
409 | #ifdef SERIAL_DEBUG_OPEN | |
410 | printk("doing serial hangup..."); | |
411 | #endif | |
7188dc20 JS |
412 | if (port->tty) |
413 | tty_hangup(port->tty); | |
1da177e4 LT |
414 | } |
415 | } | |
f21ec3d2 | 416 | if (tty_port_cts_enabled(port)) { |
7188dc20 | 417 | if (port->tty->hw_stopped) { |
1da177e4 LT |
418 | if (!(status & SER_CTS)) { |
419 | #if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW)) | |
420 | printk("CTS tx start..."); | |
421 | #endif | |
7188dc20 | 422 | port->tty->hw_stopped = 0; |
1da177e4 LT |
423 | info->IER |= UART_IER_THRI; |
424 | custom.intena = IF_SETCLR | IF_TBE; | |
425 | mb(); | |
426 | /* set a pending Tx Interrupt, transmitter should restart now */ | |
427 | custom.intreq = IF_SETCLR | IF_TBE; | |
428 | mb(); | |
7188dc20 | 429 | tty_wakeup(port->tty); |
1da177e4 LT |
430 | return; |
431 | } | |
432 | } else { | |
433 | if ((status & SER_CTS)) { | |
434 | #if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW)) | |
435 | printk("CTS tx stop..."); | |
436 | #endif | |
7188dc20 | 437 | port->tty->hw_stopped = 1; |
1da177e4 LT |
438 | info->IER &= ~UART_IER_THRI; |
439 | /* disable Tx interrupt and remove any pending interrupts */ | |
440 | custom.intena = IF_TBE; | |
441 | mb(); | |
442 | custom.intreq = IF_TBE; | |
443 | mb(); | |
444 | } | |
445 | } | |
446 | } | |
447 | } | |
448 | ||
7d12e780 | 449 | static irqreturn_t ser_vbl_int( int irq, void *data) |
1da177e4 LT |
450 | { |
451 | /* vbl is just a periodic interrupt we tie into to update modem status */ | |
916b7656 | 452 | struct serial_state *info = data; |
1da177e4 LT |
453 | /* |
454 | * TBD - is it better to unregister from this interrupt or to | |
455 | * ignore it if MSI is clear ? | |
456 | */ | |
457 | if(info->IER & UART_IER_MSI) | |
458 | check_modem_status(info); | |
459 | return IRQ_HANDLED; | |
460 | } | |
461 | ||
7d12e780 | 462 | static irqreturn_t ser_rx_int(int irq, void *dev_id) |
1da177e4 | 463 | { |
916b7656 | 464 | struct serial_state *info = dev_id; |
1da177e4 LT |
465 | |
466 | #ifdef SERIAL_DEBUG_INTR | |
467 | printk("ser_rx_int..."); | |
468 | #endif | |
469 | ||
87758791 | 470 | if (!info->tport.tty) |
1da177e4 LT |
471 | return IRQ_NONE; |
472 | ||
473 | receive_chars(info); | |
1da177e4 LT |
474 | #ifdef SERIAL_DEBUG_INTR |
475 | printk("end.\n"); | |
476 | #endif | |
477 | return IRQ_HANDLED; | |
478 | } | |
479 | ||
7d12e780 | 480 | static irqreturn_t ser_tx_int(int irq, void *dev_id) |
1da177e4 | 481 | { |
916b7656 | 482 | struct serial_state *info = dev_id; |
1da177e4 LT |
483 | |
484 | if (custom.serdatr & SDR_TBE) { | |
485 | #ifdef SERIAL_DEBUG_INTR | |
486 | printk("ser_tx_int..."); | |
487 | #endif | |
488 | ||
87758791 | 489 | if (!info->tport.tty) |
1da177e4 LT |
490 | return IRQ_NONE; |
491 | ||
492 | transmit_chars(info); | |
1da177e4 LT |
493 | #ifdef SERIAL_DEBUG_INTR |
494 | printk("end.\n"); | |
495 | #endif | |
496 | } | |
497 | return IRQ_HANDLED; | |
498 | } | |
499 | ||
500 | /* | |
501 | * ------------------------------------------------------------------- | |
502 | * Here ends the serial interrupt routines. | |
503 | * ------------------------------------------------------------------- | |
504 | */ | |
505 | ||
1da177e4 LT |
506 | /* |
507 | * --------------------------------------------------------------- | |
508 | * Low level utility subroutines for the serial driver: routines to | |
509 | * figure out the appropriate timeout for an interrupt chain, routines | |
510 | * to initialize and startup a serial port, and routines to shutdown a | |
511 | * serial port. Useful stuff like that. | |
512 | * --------------------------------------------------------------- | |
513 | */ | |
514 | ||
588993dd | 515 | static int startup(struct tty_struct *tty, struct serial_state *info) |
1da177e4 | 516 | { |
01bd730d | 517 | struct tty_port *port = &info->tport; |
1da177e4 LT |
518 | unsigned long flags; |
519 | int retval=0; | |
520 | unsigned long page; | |
521 | ||
522 | page = get_zeroed_page(GFP_KERNEL); | |
523 | if (!page) | |
524 | return -ENOMEM; | |
525 | ||
526 | local_irq_save(flags); | |
527 | ||
01bd730d | 528 | if (port->flags & ASYNC_INITIALIZED) { |
1da177e4 LT |
529 | free_page(page); |
530 | goto errout; | |
531 | } | |
532 | ||
533 | if (info->xmit.buf) | |
534 | free_page(page); | |
535 | else | |
536 | info->xmit.buf = (unsigned char *) page; | |
537 | ||
538 | #ifdef SERIAL_DEBUG_OPEN | |
539 | printk("starting up ttys%d ...", info->line); | |
540 | #endif | |
541 | ||
542 | /* Clear anything in the input buffer */ | |
543 | ||
544 | custom.intreq = IF_RBF; | |
545 | mb(); | |
546 | ||
547 | retval = request_irq(IRQ_AMIGA_VERTB, ser_vbl_int, 0, "serial status", info); | |
548 | if (retval) { | |
549 | if (serial_isroot()) { | |
588993dd | 550 | set_bit(TTY_IO_ERROR, &tty->flags); |
1da177e4 LT |
551 | retval = 0; |
552 | } | |
553 | goto errout; | |
554 | } | |
555 | ||
556 | /* enable both Rx and Tx interrupts */ | |
557 | custom.intena = IF_SETCLR | IF_RBF | IF_TBE; | |
558 | mb(); | |
559 | info->IER = UART_IER_MSI; | |
560 | ||
561 | /* remember current state of the DCD and CTS bits */ | |
562 | current_ctl_bits = ciab.pra & (SER_DCD | SER_CTS | SER_DSR); | |
563 | ||
1da177e4 | 564 | info->MCR = 0; |
588993dd | 565 | if (C_BAUD(tty)) |
1da177e4 LT |
566 | info->MCR = SER_DTR | SER_RTS; |
567 | rtsdtr_ctrl(info->MCR); | |
568 | ||
588993dd | 569 | clear_bit(TTY_IO_ERROR, &tty->flags); |
1da177e4 LT |
570 | info->xmit.head = info->xmit.tail = 0; |
571 | ||
572 | /* | |
573 | * Set up the tty->alt_speed kludge | |
574 | */ | |
01bd730d | 575 | if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) |
588993dd | 576 | tty->alt_speed = 57600; |
01bd730d | 577 | if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) |
588993dd | 578 | tty->alt_speed = 115200; |
01bd730d | 579 | if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) |
588993dd | 580 | tty->alt_speed = 230400; |
01bd730d | 581 | if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) |
588993dd | 582 | tty->alt_speed = 460800; |
1da177e4 LT |
583 | |
584 | /* | |
585 | * and set the speed of the serial port | |
586 | */ | |
588993dd | 587 | change_speed(tty, info, NULL); |
1da177e4 | 588 | |
01bd730d | 589 | port->flags |= ASYNC_INITIALIZED; |
1da177e4 LT |
590 | local_irq_restore(flags); |
591 | return 0; | |
592 | ||
593 | errout: | |
594 | local_irq_restore(flags); | |
595 | return retval; | |
596 | } | |
597 | ||
598 | /* | |
599 | * This routine will shutdown a serial port; interrupts are disabled, and | |
600 | * DTR is dropped if the hangup on close termio flag is on. | |
601 | */ | |
588993dd | 602 | static void shutdown(struct tty_struct *tty, struct serial_state *info) |
1da177e4 LT |
603 | { |
604 | unsigned long flags; | |
605 | struct serial_state *state; | |
606 | ||
01bd730d | 607 | if (!(info->tport.flags & ASYNC_INITIALIZED)) |
1da177e4 LT |
608 | return; |
609 | ||
916b7656 | 610 | state = info; |
1da177e4 LT |
611 | |
612 | #ifdef SERIAL_DEBUG_OPEN | |
613 | printk("Shutting down serial port %d ....\n", info->line); | |
614 | #endif | |
615 | ||
616 | local_irq_save(flags); /* Disable interrupts */ | |
617 | ||
618 | /* | |
619 | * clear delta_msr_wait queue to avoid mem leaks: we may free the irq | |
620 | * here so the queue might never be waken up | |
621 | */ | |
87758791 | 622 | wake_up_interruptible(&info->tport.delta_msr_wait); |
1da177e4 | 623 | |
1da177e4 LT |
624 | /* |
625 | * Free the IRQ, if necessary | |
626 | */ | |
627 | free_irq(IRQ_AMIGA_VERTB, info); | |
628 | ||
629 | if (info->xmit.buf) { | |
630 | free_page((unsigned long) info->xmit.buf); | |
631 | info->xmit.buf = NULL; | |
632 | } | |
633 | ||
634 | info->IER = 0; | |
635 | custom.intena = IF_RBF | IF_TBE; | |
636 | mb(); | |
637 | ||
638 | /* disable break condition */ | |
639 | custom.adkcon = AC_UARTBRK; | |
640 | mb(); | |
641 | ||
adc8d746 | 642 | if (tty->termios.c_cflag & HUPCL) |
1da177e4 LT |
643 | info->MCR &= ~(SER_DTR|SER_RTS); |
644 | rtsdtr_ctrl(info->MCR); | |
645 | ||
588993dd | 646 | set_bit(TTY_IO_ERROR, &tty->flags); |
1da177e4 | 647 | |
01bd730d | 648 | info->tport.flags &= ~ASYNC_INITIALIZED; |
1da177e4 LT |
649 | local_irq_restore(flags); |
650 | } | |
651 | ||
652 | ||
653 | /* | |
654 | * This routine is called to set the UART divisor registers to match | |
655 | * the specified baud rate for a serial port. | |
656 | */ | |
588993dd | 657 | static void change_speed(struct tty_struct *tty, struct serial_state *info, |
606d099c | 658 | struct ktermios *old_termios) |
1da177e4 | 659 | { |
01bd730d | 660 | struct tty_port *port = &info->tport; |
1da177e4 LT |
661 | int quot = 0, baud_base, baud; |
662 | unsigned cflag, cval = 0; | |
663 | int bits; | |
664 | unsigned long flags; | |
665 | ||
adc8d746 | 666 | cflag = tty->termios.c_cflag; |
1da177e4 LT |
667 | |
668 | /* Byte size is always 8 bits plus parity bit if requested */ | |
669 | ||
670 | cval = 3; bits = 10; | |
671 | if (cflag & CSTOPB) { | |
672 | cval |= 0x04; | |
673 | bits++; | |
674 | } | |
675 | if (cflag & PARENB) { | |
676 | cval |= UART_LCR_PARITY; | |
677 | bits++; | |
678 | } | |
679 | if (!(cflag & PARODD)) | |
680 | cval |= UART_LCR_EPAR; | |
681 | #ifdef CMSPAR | |
682 | if (cflag & CMSPAR) | |
683 | cval |= UART_LCR_SPAR; | |
684 | #endif | |
685 | ||
686 | /* Determine divisor based on baud rate */ | |
588993dd | 687 | baud = tty_get_baud_rate(tty); |
1da177e4 LT |
688 | if (!baud) |
689 | baud = 9600; /* B0 transition handled in rs_set_termios */ | |
916b7656 | 690 | baud_base = info->baud_base; |
01bd730d | 691 | if (baud == 38400 && (port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) |
916b7656 | 692 | quot = info->custom_divisor; |
1da177e4 LT |
693 | else { |
694 | if (baud == 134) | |
695 | /* Special case since 134 is really 134.5 */ | |
696 | quot = (2*baud_base / 269); | |
697 | else if (baud) | |
698 | quot = baud_base / baud; | |
699 | } | |
700 | /* If the quotient is zero refuse the change */ | |
701 | if (!quot && old_termios) { | |
db0ef08e | 702 | /* FIXME: Will need updating for new tty in the end */ |
adc8d746 AC |
703 | tty->termios.c_cflag &= ~CBAUD; |
704 | tty->termios.c_cflag |= (old_termios->c_cflag & CBAUD); | |
588993dd | 705 | baud = tty_get_baud_rate(tty); |
1da177e4 LT |
706 | if (!baud) |
707 | baud = 9600; | |
708 | if (baud == 38400 && | |
01bd730d | 709 | (port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) |
916b7656 | 710 | quot = info->custom_divisor; |
1da177e4 LT |
711 | else { |
712 | if (baud == 134) | |
713 | /* Special case since 134 is really 134.5 */ | |
714 | quot = (2*baud_base / 269); | |
715 | else if (baud) | |
716 | quot = baud_base / baud; | |
717 | } | |
718 | } | |
719 | /* As a last resort, if the quotient is zero, default to 9600 bps */ | |
720 | if (!quot) | |
721 | quot = baud_base / 9600; | |
722 | info->quot = quot; | |
916b7656 | 723 | info->timeout = ((info->xmit_fifo_size*HZ*bits*quot) / baud_base); |
1da177e4 LT |
724 | info->timeout += HZ/50; /* Add .02 seconds of slop */ |
725 | ||
726 | /* CTS flow control flag and modem status interrupts */ | |
727 | info->IER &= ~UART_IER_MSI; | |
01bd730d | 728 | if (port->flags & ASYNC_HARDPPS_CD) |
1da177e4 LT |
729 | info->IER |= UART_IER_MSI; |
730 | if (cflag & CRTSCTS) { | |
01bd730d | 731 | port->flags |= ASYNC_CTS_FLOW; |
1da177e4 LT |
732 | info->IER |= UART_IER_MSI; |
733 | } else | |
01bd730d | 734 | port->flags &= ~ASYNC_CTS_FLOW; |
1da177e4 | 735 | if (cflag & CLOCAL) |
01bd730d | 736 | port->flags &= ~ASYNC_CHECK_CD; |
1da177e4 | 737 | else { |
01bd730d | 738 | port->flags |= ASYNC_CHECK_CD; |
1da177e4 LT |
739 | info->IER |= UART_IER_MSI; |
740 | } | |
741 | /* TBD: | |
4b512d26 | 742 | * Does clearing IER_MSI imply that we should disable the VBL interrupt ? |
1da177e4 LT |
743 | */ |
744 | ||
745 | /* | |
746 | * Set up parity check flag | |
747 | */ | |
1da177e4 LT |
748 | |
749 | info->read_status_mask = UART_LSR_OE | UART_LSR_DR; | |
588993dd | 750 | if (I_INPCK(tty)) |
1da177e4 | 751 | info->read_status_mask |= UART_LSR_FE | UART_LSR_PE; |
588993dd | 752 | if (I_BRKINT(tty) || I_PARMRK(tty)) |
1da177e4 LT |
753 | info->read_status_mask |= UART_LSR_BI; |
754 | ||
755 | /* | |
756 | * Characters to ignore | |
757 | */ | |
758 | info->ignore_status_mask = 0; | |
588993dd | 759 | if (I_IGNPAR(tty)) |
1da177e4 | 760 | info->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; |
588993dd | 761 | if (I_IGNBRK(tty)) { |
1da177e4 LT |
762 | info->ignore_status_mask |= UART_LSR_BI; |
763 | /* | |
764 | * If we're ignore parity and break indicators, ignore | |
765 | * overruns too. (For real raw support). | |
766 | */ | |
588993dd | 767 | if (I_IGNPAR(tty)) |
1da177e4 LT |
768 | info->ignore_status_mask |= UART_LSR_OE; |
769 | } | |
770 | /* | |
771 | * !!! ignore all characters if CREAD is not set | |
772 | */ | |
773 | if ((cflag & CREAD) == 0) | |
774 | info->ignore_status_mask |= UART_LSR_DR; | |
775 | local_irq_save(flags); | |
776 | ||
777 | { | |
778 | short serper; | |
779 | ||
780 | /* Set up the baud rate */ | |
781 | serper = quot - 1; | |
782 | ||
783 | /* Enable or disable parity bit */ | |
784 | ||
785 | if(cval & UART_LCR_PARITY) | |
786 | serper |= (SERPER_PARENB); | |
787 | ||
788 | custom.serper = serper; | |
789 | mb(); | |
790 | } | |
791 | ||
1da177e4 LT |
792 | local_irq_restore(flags); |
793 | } | |
794 | ||
257afa3c | 795 | static int rs_put_char(struct tty_struct *tty, unsigned char ch) |
1da177e4 | 796 | { |
916b7656 | 797 | struct serial_state *info; |
1da177e4 LT |
798 | unsigned long flags; |
799 | ||
d9ad7ef1 TJRMI |
800 | info = tty->driver_data; |
801 | ||
1da177e4 | 802 | if (serial_paranoia_check(info, tty->name, "rs_put_char")) |
257afa3c | 803 | return 0; |
1da177e4 | 804 | |
d9ad7ef1 | 805 | if (!info->xmit.buf) |
257afa3c | 806 | return 0; |
1da177e4 LT |
807 | |
808 | local_irq_save(flags); | |
809 | if (CIRC_SPACE(info->xmit.head, | |
810 | info->xmit.tail, | |
811 | SERIAL_XMIT_SIZE) == 0) { | |
812 | local_irq_restore(flags); | |
257afa3c | 813 | return 0; |
1da177e4 LT |
814 | } |
815 | ||
816 | info->xmit.buf[info->xmit.head++] = ch; | |
817 | info->xmit.head &= SERIAL_XMIT_SIZE-1; | |
818 | local_irq_restore(flags); | |
257afa3c | 819 | return 1; |
1da177e4 LT |
820 | } |
821 | ||
822 | static void rs_flush_chars(struct tty_struct *tty) | |
823 | { | |
916b7656 | 824 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
825 | unsigned long flags; |
826 | ||
827 | if (serial_paranoia_check(info, tty->name, "rs_flush_chars")) | |
828 | return; | |
829 | ||
830 | if (info->xmit.head == info->xmit.tail | |
831 | || tty->stopped | |
832 | || tty->hw_stopped | |
833 | || !info->xmit.buf) | |
834 | return; | |
835 | ||
836 | local_irq_save(flags); | |
837 | info->IER |= UART_IER_THRI; | |
838 | custom.intena = IF_SETCLR | IF_TBE; | |
839 | mb(); | |
840 | /* set a pending Tx Interrupt, transmitter should restart now */ | |
841 | custom.intreq = IF_SETCLR | IF_TBE; | |
842 | mb(); | |
843 | local_irq_restore(flags); | |
844 | } | |
845 | ||
846 | static int rs_write(struct tty_struct * tty, const unsigned char *buf, int count) | |
847 | { | |
848 | int c, ret = 0; | |
916b7656 | 849 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
850 | unsigned long flags; |
851 | ||
852 | if (serial_paranoia_check(info, tty->name, "rs_write")) | |
853 | return 0; | |
854 | ||
b3218a79 | 855 | if (!info->xmit.buf) |
1da177e4 LT |
856 | return 0; |
857 | ||
3abf3bed | 858 | local_irq_save(flags); |
1da177e4 LT |
859 | while (1) { |
860 | c = CIRC_SPACE_TO_END(info->xmit.head, | |
861 | info->xmit.tail, | |
862 | SERIAL_XMIT_SIZE); | |
863 | if (count < c) | |
864 | c = count; | |
865 | if (c <= 0) { | |
866 | break; | |
867 | } | |
868 | memcpy(info->xmit.buf + info->xmit.head, buf, c); | |
869 | info->xmit.head = ((info->xmit.head + c) & | |
870 | (SERIAL_XMIT_SIZE-1)); | |
871 | buf += c; | |
872 | count -= c; | |
873 | ret += c; | |
874 | } | |
875 | local_irq_restore(flags); | |
876 | ||
877 | if (info->xmit.head != info->xmit.tail | |
878 | && !tty->stopped | |
879 | && !tty->hw_stopped | |
880 | && !(info->IER & UART_IER_THRI)) { | |
881 | info->IER |= UART_IER_THRI; | |
882 | local_irq_disable(); | |
883 | custom.intena = IF_SETCLR | IF_TBE; | |
884 | mb(); | |
885 | /* set a pending Tx Interrupt, transmitter should restart now */ | |
886 | custom.intreq = IF_SETCLR | IF_TBE; | |
887 | mb(); | |
888 | local_irq_restore(flags); | |
889 | } | |
890 | return ret; | |
891 | } | |
892 | ||
893 | static int rs_write_room(struct tty_struct *tty) | |
894 | { | |
916b7656 | 895 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
896 | |
897 | if (serial_paranoia_check(info, tty->name, "rs_write_room")) | |
898 | return 0; | |
899 | return CIRC_SPACE(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); | |
900 | } | |
901 | ||
902 | static int rs_chars_in_buffer(struct tty_struct *tty) | |
903 | { | |
916b7656 | 904 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
905 | |
906 | if (serial_paranoia_check(info, tty->name, "rs_chars_in_buffer")) | |
907 | return 0; | |
908 | return CIRC_CNT(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); | |
909 | } | |
910 | ||
911 | static void rs_flush_buffer(struct tty_struct *tty) | |
912 | { | |
916b7656 | 913 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
914 | unsigned long flags; |
915 | ||
916 | if (serial_paranoia_check(info, tty->name, "rs_flush_buffer")) | |
917 | return; | |
918 | local_irq_save(flags); | |
919 | info->xmit.head = info->xmit.tail = 0; | |
920 | local_irq_restore(flags); | |
1da177e4 LT |
921 | tty_wakeup(tty); |
922 | } | |
923 | ||
924 | /* | |
925 | * This function is used to send a high-priority XON/XOFF character to | |
926 | * the device | |
927 | */ | |
928 | static void rs_send_xchar(struct tty_struct *tty, char ch) | |
929 | { | |
916b7656 | 930 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
931 | unsigned long flags; |
932 | ||
1d6a5e4c | 933 | if (serial_paranoia_check(info, tty->name, "rs_send_xchar")) |
1da177e4 LT |
934 | return; |
935 | ||
936 | info->x_char = ch; | |
937 | if (ch) { | |
938 | /* Make sure transmit interrupts are on */ | |
939 | ||
940 | /* Check this ! */ | |
941 | local_irq_save(flags); | |
942 | if(!(custom.intenar & IF_TBE)) { | |
943 | custom.intena = IF_SETCLR | IF_TBE; | |
944 | mb(); | |
945 | /* set a pending Tx Interrupt, transmitter should restart now */ | |
946 | custom.intreq = IF_SETCLR | IF_TBE; | |
947 | mb(); | |
948 | } | |
949 | local_irq_restore(flags); | |
950 | ||
951 | info->IER |= UART_IER_THRI; | |
952 | } | |
953 | } | |
954 | ||
955 | /* | |
956 | * ------------------------------------------------------------ | |
957 | * rs_throttle() | |
958 | * | |
959 | * This routine is called by the upper-layer tty layer to signal that | |
960 | * incoming characters should be throttled. | |
961 | * ------------------------------------------------------------ | |
962 | */ | |
963 | static void rs_throttle(struct tty_struct * tty) | |
964 | { | |
916b7656 | 965 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
966 | unsigned long flags; |
967 | #ifdef SERIAL_DEBUG_THROTTLE | |
429b4749 | 968 | printk("throttle %s: %d....\n", tty_name(tty), |
1da177e4 LT |
969 | tty->ldisc.chars_in_buffer(tty)); |
970 | #endif | |
971 | ||
972 | if (serial_paranoia_check(info, tty->name, "rs_throttle")) | |
973 | return; | |
974 | ||
975 | if (I_IXOFF(tty)) | |
976 | rs_send_xchar(tty, STOP_CHAR(tty)); | |
977 | ||
adc8d746 | 978 | if (tty->termios.c_cflag & CRTSCTS) |
1da177e4 LT |
979 | info->MCR &= ~SER_RTS; |
980 | ||
981 | local_irq_save(flags); | |
982 | rtsdtr_ctrl(info->MCR); | |
983 | local_irq_restore(flags); | |
984 | } | |
985 | ||
986 | static void rs_unthrottle(struct tty_struct * tty) | |
987 | { | |
916b7656 | 988 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
989 | unsigned long flags; |
990 | #ifdef SERIAL_DEBUG_THROTTLE | |
429b4749 | 991 | printk("unthrottle %s: %d....\n", tty_name(tty), |
1da177e4 LT |
992 | tty->ldisc.chars_in_buffer(tty)); |
993 | #endif | |
994 | ||
995 | if (serial_paranoia_check(info, tty->name, "rs_unthrottle")) | |
996 | return; | |
997 | ||
998 | if (I_IXOFF(tty)) { | |
999 | if (info->x_char) | |
1000 | info->x_char = 0; | |
1001 | else | |
1002 | rs_send_xchar(tty, START_CHAR(tty)); | |
1003 | } | |
adc8d746 | 1004 | if (tty->termios.c_cflag & CRTSCTS) |
1da177e4 LT |
1005 | info->MCR |= SER_RTS; |
1006 | local_irq_save(flags); | |
1007 | rtsdtr_ctrl(info->MCR); | |
1008 | local_irq_restore(flags); | |
1009 | } | |
1010 | ||
1011 | /* | |
1012 | * ------------------------------------------------------------ | |
1013 | * rs_ioctl() and friends | |
1014 | * ------------------------------------------------------------ | |
1015 | */ | |
1016 | ||
ff169e5c | 1017 | static int get_serial_info(struct tty_struct *tty, struct serial_state *state, |
ab14caec | 1018 | struct serial_struct __user * retinfo) |
1da177e4 LT |
1019 | { |
1020 | struct serial_struct tmp; | |
1da177e4 LT |
1021 | |
1022 | if (!retinfo) | |
1023 | return -EFAULT; | |
1024 | memset(&tmp, 0, sizeof(tmp)); | |
89c8d91e | 1025 | tty_lock(tty); |
ff169e5c | 1026 | tmp.line = tty->index; |
1da177e4 | 1027 | tmp.port = state->port; |
01bd730d | 1028 | tmp.flags = state->tport.flags; |
1da177e4 LT |
1029 | tmp.xmit_fifo_size = state->xmit_fifo_size; |
1030 | tmp.baud_base = state->baud_base; | |
799be6ff JS |
1031 | tmp.close_delay = state->tport.close_delay; |
1032 | tmp.closing_wait = state->tport.closing_wait; | |
1da177e4 | 1033 | tmp.custom_divisor = state->custom_divisor; |
89c8d91e | 1034 | tty_unlock(tty); |
1da177e4 LT |
1035 | if (copy_to_user(retinfo,&tmp,sizeof(*retinfo))) |
1036 | return -EFAULT; | |
1037 | return 0; | |
1038 | } | |
1039 | ||
588993dd | 1040 | static int set_serial_info(struct tty_struct *tty, struct serial_state *state, |
ab14caec | 1041 | struct serial_struct __user * new_info) |
1da177e4 | 1042 | { |
01bd730d | 1043 | struct tty_port *port = &state->tport; |
1da177e4 | 1044 | struct serial_struct new_serial; |
0f9b9684 | 1045 | bool change_spd; |
1da177e4 LT |
1046 | int retval = 0; |
1047 | ||
1048 | if (copy_from_user(&new_serial,new_info,sizeof(new_serial))) | |
1049 | return -EFAULT; | |
e18ce49b | 1050 | |
89c8d91e | 1051 | tty_lock(tty); |
01bd730d | 1052 | change_spd = ((new_serial.flags ^ port->flags) & ASYNC_SPD_MASK) || |
0f9b9684 | 1053 | new_serial.custom_divisor != state->custom_divisor; |
ff169e5c | 1054 | if (new_serial.irq || new_serial.port != state->port || |
0f9b9684 | 1055 | new_serial.xmit_fifo_size != state->xmit_fifo_size) { |
89c8d91e | 1056 | tty_unlock(tty); |
0f9b9684 | 1057 | return -EINVAL; |
e18ce49b | 1058 | } |
1da177e4 LT |
1059 | |
1060 | if (!serial_isroot()) { | |
1061 | if ((new_serial.baud_base != state->baud_base) || | |
01bd730d | 1062 | (new_serial.close_delay != port->close_delay) || |
1da177e4 LT |
1063 | (new_serial.xmit_fifo_size != state->xmit_fifo_size) || |
1064 | ((new_serial.flags & ~ASYNC_USR_MASK) != | |
d3a7b83f | 1065 | (port->flags & ~ASYNC_USR_MASK))) { |
89c8d91e | 1066 | tty_unlock(tty); |
1da177e4 | 1067 | return -EPERM; |
d3a7b83f | 1068 | } |
01bd730d | 1069 | port->flags = ((port->flags & ~ASYNC_USR_MASK) | |
1da177e4 | 1070 | (new_serial.flags & ASYNC_USR_MASK)); |
1da177e4 LT |
1071 | state->custom_divisor = new_serial.custom_divisor; |
1072 | goto check_and_exit; | |
1073 | } | |
1074 | ||
e18ce49b | 1075 | if (new_serial.baud_base < 9600) { |
89c8d91e | 1076 | tty_unlock(tty); |
1da177e4 | 1077 | return -EINVAL; |
e18ce49b | 1078 | } |
1da177e4 LT |
1079 | |
1080 | /* | |
1081 | * OK, past this point, all the error checking has been done. | |
1082 | * At this point, we start making changes..... | |
1083 | */ | |
1084 | ||
1085 | state->baud_base = new_serial.baud_base; | |
01bd730d | 1086 | port->flags = ((port->flags & ~ASYNC_FLAGS) | |
1da177e4 | 1087 | (new_serial.flags & ASYNC_FLAGS)); |
1da177e4 | 1088 | state->custom_divisor = new_serial.custom_divisor; |
01bd730d JS |
1089 | port->close_delay = new_serial.close_delay * HZ/100; |
1090 | port->closing_wait = new_serial.closing_wait * HZ/100; | |
d6c53c0e | 1091 | port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0; |
1da177e4 LT |
1092 | |
1093 | check_and_exit: | |
01bd730d | 1094 | if (port->flags & ASYNC_INITIALIZED) { |
0f9b9684 | 1095 | if (change_spd) { |
01bd730d | 1096 | if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) |
588993dd | 1097 | tty->alt_speed = 57600; |
01bd730d | 1098 | if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) |
588993dd | 1099 | tty->alt_speed = 115200; |
01bd730d | 1100 | if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) |
588993dd | 1101 | tty->alt_speed = 230400; |
01bd730d | 1102 | if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) |
588993dd JS |
1103 | tty->alt_speed = 460800; |
1104 | change_speed(tty, state, NULL); | |
1da177e4 LT |
1105 | } |
1106 | } else | |
588993dd | 1107 | retval = startup(tty, state); |
89c8d91e | 1108 | tty_unlock(tty); |
1da177e4 LT |
1109 | return retval; |
1110 | } | |
1111 | ||
1112 | ||
1113 | /* | |
1114 | * get_lsr_info - get line status register info | |
1115 | * | |
1116 | * Purpose: Let user call ioctl() to get info when the UART physically | |
1117 | * is emptied. On bus types like RS485, the transmitter must | |
1118 | * release the bus after transmitting. This must be done when | |
1119 | * the transmit shift register is empty, not be done when the | |
1120 | * transmit holding register is empty. This functionality | |
1121 | * allows an RS485 driver to be written in user space. | |
1122 | */ | |
916b7656 | 1123 | static int get_lsr_info(struct serial_state *info, unsigned int __user *value) |
1da177e4 LT |
1124 | { |
1125 | unsigned char status; | |
1126 | unsigned int result; | |
1127 | unsigned long flags; | |
1128 | ||
1129 | local_irq_save(flags); | |
1130 | status = custom.serdatr; | |
1131 | mb(); | |
1132 | local_irq_restore(flags); | |
1133 | result = ((status & SDR_TSRE) ? TIOCSER_TEMT : 0); | |
1134 | if (copy_to_user(value, &result, sizeof(int))) | |
1135 | return -EFAULT; | |
1136 | return 0; | |
1137 | } | |
1138 | ||
1139 | ||
60b33c13 | 1140 | static int rs_tiocmget(struct tty_struct *tty) |
1da177e4 | 1141 | { |
916b7656 | 1142 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
1143 | unsigned char control, status; |
1144 | unsigned long flags; | |
1145 | ||
1146 | if (serial_paranoia_check(info, tty->name, "rs_ioctl")) | |
1147 | return -ENODEV; | |
1148 | if (tty->flags & (1 << TTY_IO_ERROR)) | |
1149 | return -EIO; | |
1150 | ||
1151 | control = info->MCR; | |
1152 | local_irq_save(flags); | |
1153 | status = ciab.pra; | |
1154 | local_irq_restore(flags); | |
1155 | return ((control & SER_RTS) ? TIOCM_RTS : 0) | |
1156 | | ((control & SER_DTR) ? TIOCM_DTR : 0) | |
1157 | | (!(status & SER_DCD) ? TIOCM_CAR : 0) | |
1158 | | (!(status & SER_DSR) ? TIOCM_DSR : 0) | |
1159 | | (!(status & SER_CTS) ? TIOCM_CTS : 0); | |
1160 | } | |
1161 | ||
20b9d177 AC |
1162 | static int rs_tiocmset(struct tty_struct *tty, unsigned int set, |
1163 | unsigned int clear) | |
1da177e4 | 1164 | { |
916b7656 | 1165 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
1166 | unsigned long flags; |
1167 | ||
1168 | if (serial_paranoia_check(info, tty->name, "rs_ioctl")) | |
1169 | return -ENODEV; | |
1170 | if (tty->flags & (1 << TTY_IO_ERROR)) | |
1171 | return -EIO; | |
1172 | ||
1173 | local_irq_save(flags); | |
1174 | if (set & TIOCM_RTS) | |
1175 | info->MCR |= SER_RTS; | |
1176 | if (set & TIOCM_DTR) | |
1177 | info->MCR |= SER_DTR; | |
1178 | if (clear & TIOCM_RTS) | |
1179 | info->MCR &= ~SER_RTS; | |
1180 | if (clear & TIOCM_DTR) | |
1181 | info->MCR &= ~SER_DTR; | |
1182 | rtsdtr_ctrl(info->MCR); | |
1183 | local_irq_restore(flags); | |
1184 | return 0; | |
1185 | } | |
1186 | ||
1187 | /* | |
1188 | * rs_break() --- routine which turns the break handling on or off | |
1189 | */ | |
9e98966c | 1190 | static int rs_break(struct tty_struct *tty, int break_state) |
1da177e4 | 1191 | { |
916b7656 | 1192 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
1193 | unsigned long flags; |
1194 | ||
1195 | if (serial_paranoia_check(info, tty->name, "rs_break")) | |
970a8a51 | 1196 | return -EINVAL; |
1da177e4 LT |
1197 | |
1198 | local_irq_save(flags); | |
1199 | if (break_state == -1) | |
1200 | custom.adkcon = AC_SETCLR | AC_UARTBRK; | |
1201 | else | |
1202 | custom.adkcon = AC_UARTBRK; | |
1203 | mb(); | |
1204 | local_irq_restore(flags); | |
9e98966c | 1205 | return 0; |
1da177e4 LT |
1206 | } |
1207 | ||
0587102c AC |
1208 | /* |
1209 | * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) | |
1210 | * Return: write counters to the user passed counter struct | |
1211 | * NB: both 1->0 and 0->1 transitions are counted except for | |
1212 | * RI where only 0->1 is counted. | |
1213 | */ | |
1214 | static int rs_get_icount(struct tty_struct *tty, | |
1215 | struct serial_icounter_struct *icount) | |
1216 | { | |
916b7656 | 1217 | struct serial_state *info = tty->driver_data; |
0587102c AC |
1218 | struct async_icount cnow; |
1219 | unsigned long flags; | |
1220 | ||
1221 | local_irq_save(flags); | |
916b7656 | 1222 | cnow = info->icount; |
0587102c AC |
1223 | local_irq_restore(flags); |
1224 | icount->cts = cnow.cts; | |
1225 | icount->dsr = cnow.dsr; | |
1226 | icount->rng = cnow.rng; | |
1227 | icount->dcd = cnow.dcd; | |
1228 | icount->rx = cnow.rx; | |
1229 | icount->tx = cnow.tx; | |
1230 | icount->frame = cnow.frame; | |
1231 | icount->overrun = cnow.overrun; | |
1232 | icount->parity = cnow.parity; | |
1233 | icount->brk = cnow.brk; | |
1234 | icount->buf_overrun = cnow.buf_overrun; | |
1235 | ||
1236 | return 0; | |
1237 | } | |
1da177e4 | 1238 | |
6caa76b7 | 1239 | static int rs_ioctl(struct tty_struct *tty, |
1da177e4 LT |
1240 | unsigned int cmd, unsigned long arg) |
1241 | { | |
916b7656 | 1242 | struct serial_state *info = tty->driver_data; |
1da177e4 | 1243 | struct async_icount cprev, cnow; /* kernel counter temps */ |
ab14caec | 1244 | void __user *argp = (void __user *)arg; |
1da177e4 | 1245 | unsigned long flags; |
591cee0a AB |
1246 | DEFINE_WAIT(wait); |
1247 | int ret; | |
1da177e4 LT |
1248 | |
1249 | if (serial_paranoia_check(info, tty->name, "rs_ioctl")) | |
1250 | return -ENODEV; | |
1251 | ||
1252 | if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) && | |
1253 | (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGSTRUCT) && | |
1254 | (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) { | |
1255 | if (tty->flags & (1 << TTY_IO_ERROR)) | |
1256 | return -EIO; | |
1257 | } | |
1258 | ||
1259 | switch (cmd) { | |
1260 | case TIOCGSERIAL: | |
ff169e5c | 1261 | return get_serial_info(tty, info, argp); |
1da177e4 | 1262 | case TIOCSSERIAL: |
588993dd | 1263 | return set_serial_info(tty, info, argp); |
1da177e4 LT |
1264 | case TIOCSERCONFIG: |
1265 | return 0; | |
1266 | ||
1267 | case TIOCSERGETLSR: /* Get line status register */ | |
ab14caec | 1268 | return get_lsr_info(info, argp); |
1da177e4 LT |
1269 | |
1270 | case TIOCSERGSTRUCT: | |
ab14caec | 1271 | if (copy_to_user(argp, |
916b7656 | 1272 | info, sizeof(struct serial_state))) |
1da177e4 LT |
1273 | return -EFAULT; |
1274 | return 0; | |
1275 | ||
1276 | /* | |
1277 | * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change | |
1278 | * - mask passed in arg for lines of interest | |
1279 | * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) | |
1280 | * Caller should use TIOCGICOUNT to see which one it was | |
1281 | */ | |
1282 | case TIOCMIWAIT: | |
1283 | local_irq_save(flags); | |
1284 | /* note the counters on entry */ | |
916b7656 | 1285 | cprev = info->icount; |
1da177e4 LT |
1286 | local_irq_restore(flags); |
1287 | while (1) { | |
591cee0a AB |
1288 | prepare_to_wait(&info->tport.delta_msr_wait, |
1289 | &wait, TASK_INTERRUPTIBLE); | |
1da177e4 | 1290 | local_irq_save(flags); |
916b7656 | 1291 | cnow = info->icount; /* atomic copy */ |
1da177e4 LT |
1292 | local_irq_restore(flags); |
1293 | if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && | |
591cee0a AB |
1294 | cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) { |
1295 | ret = -EIO; /* no change => error */ | |
1296 | break; | |
1297 | } | |
1da177e4 LT |
1298 | if ( ((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || |
1299 | ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || | |
1300 | ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || | |
1301 | ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts)) ) { | |
591cee0a AB |
1302 | ret = 0; |
1303 | break; | |
1304 | } | |
1305 | schedule(); | |
1306 | /* see if a signal did it */ | |
1307 | if (signal_pending(current)) { | |
1308 | ret = -ERESTARTSYS; | |
1309 | break; | |
1da177e4 LT |
1310 | } |
1311 | cprev = cnow; | |
1312 | } | |
591cee0a AB |
1313 | finish_wait(&info->tport.delta_msr_wait, &wait); |
1314 | return ret; | |
1da177e4 | 1315 | |
1da177e4 LT |
1316 | case TIOCSERGWILD: |
1317 | case TIOCSERSWILD: | |
1318 | /* "setserial -W" is called in Debian boot */ | |
1319 | printk ("TIOCSER?WILD ioctl obsolete, ignored.\n"); | |
1320 | return 0; | |
1321 | ||
1322 | default: | |
1323 | return -ENOIOCTLCMD; | |
1324 | } | |
1325 | return 0; | |
1326 | } | |
1327 | ||
606d099c | 1328 | static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) |
1da177e4 | 1329 | { |
916b7656 | 1330 | struct serial_state *info = tty->driver_data; |
1da177e4 | 1331 | unsigned long flags; |
adc8d746 | 1332 | unsigned int cflag = tty->termios.c_cflag; |
1da177e4 | 1333 | |
588993dd | 1334 | change_speed(tty, info, old_termios); |
1da177e4 LT |
1335 | |
1336 | /* Handle transition to B0 status */ | |
1337 | if ((old_termios->c_cflag & CBAUD) && | |
1338 | !(cflag & CBAUD)) { | |
1339 | info->MCR &= ~(SER_DTR|SER_RTS); | |
1340 | local_irq_save(flags); | |
1341 | rtsdtr_ctrl(info->MCR); | |
1342 | local_irq_restore(flags); | |
1343 | } | |
1344 | ||
1345 | /* Handle transition away from B0 status */ | |
1346 | if (!(old_termios->c_cflag & CBAUD) && | |
1347 | (cflag & CBAUD)) { | |
1348 | info->MCR |= SER_DTR; | |
adc8d746 | 1349 | if (!(tty->termios.c_cflag & CRTSCTS) || |
1da177e4 LT |
1350 | !test_bit(TTY_THROTTLED, &tty->flags)) { |
1351 | info->MCR |= SER_RTS; | |
1352 | } | |
1353 | local_irq_save(flags); | |
1354 | rtsdtr_ctrl(info->MCR); | |
1355 | local_irq_restore(flags); | |
1356 | } | |
1357 | ||
1358 | /* Handle turning off CRTSCTS */ | |
1359 | if ((old_termios->c_cflag & CRTSCTS) && | |
adc8d746 | 1360 | !(tty->termios.c_cflag & CRTSCTS)) { |
1da177e4 LT |
1361 | tty->hw_stopped = 0; |
1362 | rs_start(tty); | |
1363 | } | |
1364 | ||
1365 | #if 0 | |
1366 | /* | |
1367 | * No need to wake up processes in open wait, since they | |
1368 | * sample the CLOCAL flag once, and don't recheck it. | |
1369 | * XXX It's not clear whether the current behavior is correct | |
1370 | * or not. Hence, this may change..... | |
1371 | */ | |
1372 | if (!(old_termios->c_cflag & CLOCAL) && | |
adc8d746 | 1373 | (tty->termios.c_cflag & CLOCAL)) |
1da177e4 LT |
1374 | wake_up_interruptible(&info->open_wait); |
1375 | #endif | |
1376 | } | |
1377 | ||
1378 | /* | |
1379 | * ------------------------------------------------------------ | |
1380 | * rs_close() | |
1381 | * | |
1382 | * This routine is called when the serial port gets closed. First, we | |
1383 | * wait for the last remaining data to be sent. Then, we unlink its | |
1384 | * async structure from the interrupt chain if necessary, and we free | |
1385 | * that IRQ if nothing is left in the chain. | |
1386 | * ------------------------------------------------------------ | |
1387 | */ | |
1388 | static void rs_close(struct tty_struct *tty, struct file * filp) | |
1389 | { | |
916b7656 | 1390 | struct serial_state *state = tty->driver_data; |
7188dc20 | 1391 | struct tty_port *port = &state->tport; |
1da177e4 | 1392 | |
9b937421 | 1393 | if (serial_paranoia_check(state, tty->name, "rs_close")) |
1da177e4 LT |
1394 | return; |
1395 | ||
9b937421 | 1396 | if (tty_port_close_start(port, tty, filp) == 0) |
1da177e4 | 1397 | return; |
1da177e4 | 1398 | |
1da177e4 LT |
1399 | /* |
1400 | * At this point we stop accepting input. To do this, we | |
1401 | * disable the receive line status interrupts, and tell the | |
1402 | * interrupt driver to stop checking the data ready bit in the | |
1403 | * line status register. | |
1404 | */ | |
916b7656 | 1405 | state->read_status_mask &= ~UART_LSR_DR; |
7188dc20 | 1406 | if (port->flags & ASYNC_INITIALIZED) { |
1da177e4 LT |
1407 | /* disable receive interrupts */ |
1408 | custom.intena = IF_RBF; | |
1409 | mb(); | |
1410 | /* clear any pending receive interrupt */ | |
1411 | custom.intreq = IF_RBF; | |
1412 | mb(); | |
1413 | ||
1414 | /* | |
1415 | * Before we drop DTR, make sure the UART transmitter | |
1416 | * has completely drained; this is especially | |
1417 | * important if there is a transmit FIFO! | |
1418 | */ | |
916b7656 | 1419 | rs_wait_until_sent(tty, state->timeout); |
1da177e4 | 1420 | } |
588993dd | 1421 | shutdown(tty, state); |
978e595f | 1422 | rs_flush_buffer(tty); |
1da177e4 LT |
1423 | |
1424 | tty_ldisc_flush(tty); | |
7188dc20 | 1425 | port->tty = NULL; |
b8edebe4 JS |
1426 | |
1427 | tty_port_close_end(port, tty); | |
1da177e4 LT |
1428 | } |
1429 | ||
1430 | /* | |
1431 | * rs_wait_until_sent() --- wait until the transmitter is empty | |
1432 | */ | |
1433 | static void rs_wait_until_sent(struct tty_struct *tty, int timeout) | |
1434 | { | |
916b7656 | 1435 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
1436 | unsigned long orig_jiffies, char_time; |
1437 | int lsr; | |
1438 | ||
1439 | if (serial_paranoia_check(info, tty->name, "rs_wait_until_sent")) | |
1440 | return; | |
1441 | ||
916b7656 | 1442 | if (info->xmit_fifo_size == 0) |
1da177e4 LT |
1443 | return; /* Just in case.... */ |
1444 | ||
1445 | orig_jiffies = jiffies; | |
978e595f | 1446 | |
1da177e4 LT |
1447 | /* |
1448 | * Set the check interval to be 1/5 of the estimated time to | |
1449 | * send a single character, and make it at least 1. The check | |
1450 | * interval should also be less than the timeout. | |
1451 | * | |
1452 | * Note: we have to use pretty tight timings here to satisfy | |
1453 | * the NIST-PCTS. | |
1454 | */ | |
916b7656 | 1455 | char_time = (info->timeout - HZ/50) / info->xmit_fifo_size; |
1da177e4 LT |
1456 | char_time = char_time / 5; |
1457 | if (char_time == 0) | |
1458 | char_time = 1; | |
1459 | if (timeout) | |
1460 | char_time = min_t(unsigned long, char_time, timeout); | |
1461 | /* | |
1462 | * If the transmitter hasn't cleared in twice the approximate | |
1463 | * amount of time to send the entire FIFO, it probably won't | |
1464 | * ever clear. This assumes the UART isn't doing flow | |
1465 | * control, which is currently the case. Hence, if it ever | |
1466 | * takes longer than info->timeout, this is probably due to a | |
1467 | * UART bug of some kind. So, we clamp the timeout parameter at | |
1468 | * 2*info->timeout. | |
1469 | */ | |
1470 | if (!timeout || timeout > 2*info->timeout) | |
1471 | timeout = 2*info->timeout; | |
1472 | #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT | |
1473 | printk("In rs_wait_until_sent(%d) check=%lu...", timeout, char_time); | |
1474 | printk("jiff=%lu...", jiffies); | |
1475 | #endif | |
1476 | while(!((lsr = custom.serdatr) & SDR_TSRE)) { | |
1477 | #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT | |
1478 | printk("serdatr = %d (jiff=%lu)...", lsr, jiffies); | |
1479 | #endif | |
1480 | msleep_interruptible(jiffies_to_msecs(char_time)); | |
1481 | if (signal_pending(current)) | |
1482 | break; | |
1483 | if (timeout && time_after(jiffies, orig_jiffies + timeout)) | |
1484 | break; | |
1485 | } | |
cc0a8fbb | 1486 | __set_current_state(TASK_RUNNING); |
eff4b0b9 | 1487 | |
1da177e4 LT |
1488 | #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT |
1489 | printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies); | |
1490 | #endif | |
1491 | } | |
1492 | ||
1493 | /* | |
1494 | * rs_hangup() --- called by tty_hangup() when a hangup is signaled. | |
1495 | */ | |
1496 | static void rs_hangup(struct tty_struct *tty) | |
1497 | { | |
916b7656 | 1498 | struct serial_state *info = tty->driver_data; |
1da177e4 LT |
1499 | |
1500 | if (serial_paranoia_check(info, tty->name, "rs_hangup")) | |
1501 | return; | |
1502 | ||
1da177e4 | 1503 | rs_flush_buffer(tty); |
588993dd | 1504 | shutdown(tty, info); |
12c80354 | 1505 | info->tport.count = 0; |
01bd730d | 1506 | info->tport.flags &= ~ASYNC_NORMAL_ACTIVE; |
87758791 JS |
1507 | info->tport.tty = NULL; |
1508 | wake_up_interruptible(&info->tport.open_wait); | |
1da177e4 LT |
1509 | } |
1510 | ||
1da177e4 LT |
1511 | /* |
1512 | * This routine is called whenever a serial port is opened. It | |
1513 | * enables interrupts for a serial port, linking in its async structure into | |
1514 | * the IRQ chain. It also performs the serial-specific | |
1515 | * initialization for the tty structure. | |
1516 | */ | |
1517 | static int rs_open(struct tty_struct *tty, struct file * filp) | |
1518 | { | |
916b7656 | 1519 | struct serial_state *info = rs_table + tty->index; |
7188dc20 | 1520 | struct tty_port *port = &info->tport; |
410235fd | 1521 | int retval; |
1da177e4 | 1522 | |
7188dc20 JS |
1523 | port->count++; |
1524 | port->tty = tty; | |
916b7656 | 1525 | tty->driver_data = info; |
7188dc20 | 1526 | tty->port = port; |
1da177e4 LT |
1527 | if (serial_paranoia_check(info, tty->name, "rs_open")) |
1528 | return -ENODEV; | |
1529 | ||
d6c53c0e | 1530 | port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0; |
1da177e4 | 1531 | |
588993dd | 1532 | retval = startup(tty, info); |
1da177e4 LT |
1533 | if (retval) { |
1534 | return retval; | |
1535 | } | |
1536 | ||
6e1aeb03 | 1537 | return tty_port_block_til_ready(port, tty, filp); |
1da177e4 LT |
1538 | } |
1539 | ||
1540 | /* | |
1541 | * /proc fs routines.... | |
1542 | */ | |
1543 | ||
ff169e5c JS |
1544 | static inline void line_info(struct seq_file *m, int line, |
1545 | struct serial_state *state) | |
1da177e4 | 1546 | { |
1da177e4 | 1547 | char stat_buf[30], control, status; |
1da177e4 LT |
1548 | unsigned long flags; |
1549 | ||
ff169e5c | 1550 | seq_printf(m, "%d: uart:amiga_builtin", line); |
1da177e4 | 1551 | |
1da177e4 LT |
1552 | local_irq_save(flags); |
1553 | status = ciab.pra; | |
01bd730d | 1554 | control = (state->tport.flags & ASYNC_INITIALIZED) ? state->MCR : status; |
1da177e4 LT |
1555 | local_irq_restore(flags); |
1556 | ||
1557 | stat_buf[0] = 0; | |
1558 | stat_buf[1] = 0; | |
1559 | if(!(control & SER_RTS)) | |
1560 | strcat(stat_buf, "|RTS"); | |
1561 | if(!(status & SER_CTS)) | |
1562 | strcat(stat_buf, "|CTS"); | |
1563 | if(!(control & SER_DTR)) | |
1564 | strcat(stat_buf, "|DTR"); | |
1565 | if(!(status & SER_DSR)) | |
1566 | strcat(stat_buf, "|DSR"); | |
1567 | if(!(status & SER_DCD)) | |
1568 | strcat(stat_buf, "|CD"); | |
1569 | ||
916b7656 JS |
1570 | if (state->quot) |
1571 | seq_printf(m, " baud:%d", state->baud_base / state->quot); | |
1da177e4 | 1572 | |
d594027d | 1573 | seq_printf(m, " tx:%d rx:%d", state->icount.tx, state->icount.rx); |
1da177e4 LT |
1574 | |
1575 | if (state->icount.frame) | |
d594027d | 1576 | seq_printf(m, " fe:%d", state->icount.frame); |
1da177e4 LT |
1577 | |
1578 | if (state->icount.parity) | |
d594027d | 1579 | seq_printf(m, " pe:%d", state->icount.parity); |
1da177e4 LT |
1580 | |
1581 | if (state->icount.brk) | |
d594027d | 1582 | seq_printf(m, " brk:%d", state->icount.brk); |
1da177e4 LT |
1583 | |
1584 | if (state->icount.overrun) | |
d594027d | 1585 | seq_printf(m, " oe:%d", state->icount.overrun); |
1da177e4 LT |
1586 | |
1587 | /* | |
1588 | * Last thing is the RS-232 status lines | |
1589 | */ | |
d594027d | 1590 | seq_printf(m, " %s\n", stat_buf+1); |
1da177e4 LT |
1591 | } |
1592 | ||
d594027d | 1593 | static int rs_proc_show(struct seq_file *m, void *v) |
1da177e4 | 1594 | { |
d594027d | 1595 | seq_printf(m, "serinfo:1.0 driver:%s\n", serial_version); |
ff169e5c | 1596 | line_info(m, 0, &rs_table[0]); |
d594027d | 1597 | return 0; |
1da177e4 LT |
1598 | } |
1599 | ||
d594027d AD |
1600 | static int rs_proc_open(struct inode *inode, struct file *file) |
1601 | { | |
1602 | return single_open(file, rs_proc_show, NULL); | |
1603 | } | |
1604 | ||
1605 | static const struct file_operations rs_proc_fops = { | |
1606 | .owner = THIS_MODULE, | |
1607 | .open = rs_proc_open, | |
1608 | .read = seq_read, | |
1609 | .llseek = seq_lseek, | |
1610 | .release = single_release, | |
1611 | }; | |
1612 | ||
1da177e4 LT |
1613 | /* |
1614 | * --------------------------------------------------------------------- | |
1615 | * rs_init() and friends | |
1616 | * | |
1617 | * rs_init() is called at boot-time to initialize the serial driver. | |
1618 | * --------------------------------------------------------------------- | |
1619 | */ | |
1620 | ||
1621 | /* | |
1622 | * This routine prints out the appropriate serial driver version | |
1623 | * number, and identifies which options were configured into this | |
1624 | * driver. | |
1625 | */ | |
41c28ff1 | 1626 | static void show_serial_version(void) |
1da177e4 LT |
1627 | { |
1628 | printk(KERN_INFO "%s version %s\n", serial_name, serial_version); | |
1629 | } | |
1630 | ||
1631 | ||
b68e31d0 | 1632 | static const struct tty_operations serial_ops = { |
1da177e4 LT |
1633 | .open = rs_open, |
1634 | .close = rs_close, | |
1635 | .write = rs_write, | |
1636 | .put_char = rs_put_char, | |
1637 | .flush_chars = rs_flush_chars, | |
1638 | .write_room = rs_write_room, | |
1639 | .chars_in_buffer = rs_chars_in_buffer, | |
1640 | .flush_buffer = rs_flush_buffer, | |
1641 | .ioctl = rs_ioctl, | |
1642 | .throttle = rs_throttle, | |
1643 | .unthrottle = rs_unthrottle, | |
1644 | .set_termios = rs_set_termios, | |
1645 | .stop = rs_stop, | |
1646 | .start = rs_start, | |
1647 | .hangup = rs_hangup, | |
1648 | .break_ctl = rs_break, | |
1649 | .send_xchar = rs_send_xchar, | |
1650 | .wait_until_sent = rs_wait_until_sent, | |
1da177e4 LT |
1651 | .tiocmget = rs_tiocmget, |
1652 | .tiocmset = rs_tiocmset, | |
0587102c | 1653 | .get_icount = rs_get_icount, |
d594027d | 1654 | .proc_fops = &rs_proc_fops, |
1da177e4 LT |
1655 | }; |
1656 | ||
f1166604 JS |
1657 | static int amiga_carrier_raised(struct tty_port *port) |
1658 | { | |
1659 | return !(ciab.pra & SER_DCD); | |
1660 | } | |
1661 | ||
1662 | static void amiga_dtr_rts(struct tty_port *port, int raise) | |
1663 | { | |
1664 | struct serial_state *info = container_of(port, struct serial_state, | |
1665 | tport); | |
1666 | unsigned long flags; | |
1667 | ||
1668 | if (raise) | |
1669 | info->MCR |= SER_DTR|SER_RTS; | |
1670 | else | |
1671 | info->MCR &= ~(SER_DTR|SER_RTS); | |
1672 | ||
1673 | local_irq_save(flags); | |
1674 | rtsdtr_ctrl(info->MCR); | |
1675 | local_irq_restore(flags); | |
1676 | } | |
1677 | ||
1678 | static const struct tty_port_operations amiga_port_ops = { | |
1679 | .carrier_raised = amiga_carrier_raised, | |
1680 | .dtr_rts = amiga_dtr_rts, | |
1681 | }; | |
1682 | ||
1da177e4 LT |
1683 | /* |
1684 | * The serial driver boot-time initialization code! | |
1685 | */ | |
826e8c8c | 1686 | static int __init amiga_serial_probe(struct platform_device *pdev) |
1da177e4 LT |
1687 | { |
1688 | unsigned long flags; | |
1689 | struct serial_state * state; | |
5edc304f | 1690 | int error; |
1da177e4 | 1691 | |
410235fd | 1692 | serial_driver = alloc_tty_driver(NR_PORTS); |
1da177e4 LT |
1693 | if (!serial_driver) |
1694 | return -ENOMEM; | |
1695 | ||
1da177e4 LT |
1696 | show_serial_version(); |
1697 | ||
1698 | /* Initialize the tty_driver structure */ | |
1699 | ||
1da177e4 LT |
1700 | serial_driver->driver_name = "amiserial"; |
1701 | serial_driver->name = "ttyS"; | |
1702 | serial_driver->major = TTY_MAJOR; | |
1703 | serial_driver->minor_start = 64; | |
1704 | serial_driver->type = TTY_DRIVER_TYPE_SERIAL; | |
1705 | serial_driver->subtype = SERIAL_TYPE_NORMAL; | |
1706 | serial_driver->init_termios = tty_std_termios; | |
1707 | serial_driver->init_termios.c_cflag = | |
1708 | B9600 | CS8 | CREAD | HUPCL | CLOCAL; | |
1709 | serial_driver->flags = TTY_DRIVER_REAL_RAW; | |
1710 | tty_set_operations(serial_driver, &serial_ops); | |
1711 | ||
1da177e4 | 1712 | state = rs_table; |
1da177e4 | 1713 | state->port = (int)&custom.serdatr; /* Just to give it a value */ |
1da177e4 | 1714 | state->custom_divisor = 0; |
1da177e4 LT |
1715 | state->icount.cts = state->icount.dsr = |
1716 | state->icount.rng = state->icount.dcd = 0; | |
1717 | state->icount.rx = state->icount.tx = 0; | |
1718 | state->icount.frame = state->icount.parity = 0; | |
1719 | state->icount.overrun = state->icount.brk = 0; | |
87758791 | 1720 | tty_port_init(&state->tport); |
f1166604 | 1721 | state->tport.ops = &amiga_port_ops; |
b19e2ca7 JS |
1722 | tty_port_link_device(&state->tport, serial_driver, 0); |
1723 | ||
1724 | error = tty_register_driver(serial_driver); | |
1725 | if (error) | |
1726 | goto fail_put_tty_driver; | |
1da177e4 | 1727 | |
ff169e5c | 1728 | printk(KERN_INFO "ttyS0 is the amiga builtin serial port\n"); |
1da177e4 LT |
1729 | |
1730 | /* Hardware set up */ | |
1731 | ||
1732 | state->baud_base = amiga_colorclock; | |
1733 | state->xmit_fifo_size = 1; | |
1734 | ||
1da177e4 | 1735 | /* set ISRs, and then disable the rx interrupts */ |
5edc304f GU |
1736 | error = request_irq(IRQ_AMIGA_TBE, ser_tx_int, 0, "serial TX", state); |
1737 | if (error) | |
1738 | goto fail_unregister; | |
1739 | ||
9cfb5c05 | 1740 | error = request_irq(IRQ_AMIGA_RBF, ser_rx_int, 0, |
5edc304f GU |
1741 | "serial RX", state); |
1742 | if (error) | |
1743 | goto fail_free_irq; | |
1da177e4 | 1744 | |
c70c036f JL |
1745 | local_irq_save(flags); |
1746 | ||
1da177e4 LT |
1747 | /* turn off Rx and Tx interrupts */ |
1748 | custom.intena = IF_RBF | IF_TBE; | |
1749 | mb(); | |
1750 | ||
1751 | /* clear any pending interrupt */ | |
1752 | custom.intreq = IF_RBF | IF_TBE; | |
1753 | mb(); | |
1754 | ||
1755 | local_irq_restore(flags); | |
1756 | ||
1757 | /* | |
1758 | * set the appropriate directions for the modem control flags, | |
1759 | * and clear RTS and DTR | |
1760 | */ | |
1761 | ciab.ddra |= (SER_DTR | SER_RTS); /* outputs */ | |
1762 | ciab.ddra &= ~(SER_DCD | SER_CTS | SER_DSR); /* inputs */ | |
1763 | ||
826e8c8c GU |
1764 | platform_set_drvdata(pdev, state); |
1765 | ||
1da177e4 | 1766 | return 0; |
5edc304f GU |
1767 | |
1768 | fail_free_irq: | |
1769 | free_irq(IRQ_AMIGA_TBE, state); | |
1770 | fail_unregister: | |
1771 | tty_unregister_driver(serial_driver); | |
5edc304f | 1772 | fail_put_tty_driver: |
191c5f10 | 1773 | tty_port_destroy(&state->tport); |
5edc304f GU |
1774 | put_tty_driver(serial_driver); |
1775 | return error; | |
1da177e4 LT |
1776 | } |
1777 | ||
826e8c8c | 1778 | static int __exit amiga_serial_remove(struct platform_device *pdev) |
1da177e4 LT |
1779 | { |
1780 | int error; | |
826e8c8c | 1781 | struct serial_state *state = platform_get_drvdata(pdev); |
1da177e4 LT |
1782 | |
1783 | /* printk("Unloading %s: version %s\n", serial_name, serial_version); */ | |
2eeaf0bb GKH |
1784 | error = tty_unregister_driver(serial_driver); |
1785 | if (error) | |
1da177e4 LT |
1786 | printk("SERIAL: failed to unregister serial driver (%d)\n", |
1787 | error); | |
1788 | put_tty_driver(serial_driver); | |
191c5f10 | 1789 | tty_port_destroy(&state->tport); |
1da177e4 | 1790 | |
916b7656 JS |
1791 | free_irq(IRQ_AMIGA_TBE, state); |
1792 | free_irq(IRQ_AMIGA_RBF, state); | |
5edc304f | 1793 | |
826e8c8c GU |
1794 | return error; |
1795 | } | |
1796 | ||
1797 | static struct platform_driver amiga_serial_driver = { | |
1798 | .remove = __exit_p(amiga_serial_remove), | |
1799 | .driver = { | |
1800 | .name = "amiga-serial", | |
826e8c8c GU |
1801 | }, |
1802 | }; | |
1803 | ||
fec6bee3 | 1804 | module_platform_driver_probe(amiga_serial_driver, amiga_serial_probe); |
1da177e4 LT |
1805 | |
1806 | ||
d1a35e4d GU |
1807 | #if defined(CONFIG_SERIAL_CONSOLE) && !defined(MODULE) |
1808 | ||
1da177e4 LT |
1809 | /* |
1810 | * ------------------------------------------------------------ | |
1811 | * Serial console driver | |
1812 | * ------------------------------------------------------------ | |
1813 | */ | |
1da177e4 LT |
1814 | |
1815 | static void amiga_serial_putc(char c) | |
1816 | { | |
1817 | custom.serdat = (unsigned char)c | 0x100; | |
1818 | while (!(custom.serdatr & 0x2000)) | |
1819 | barrier(); | |
1820 | } | |
1821 | ||
1822 | /* | |
1823 | * Print a string to the serial port trying not to disturb | |
1824 | * any possible real use of the port... | |
1825 | * | |
1826 | * The console must be locked when we get here. | |
1827 | */ | |
1828 | static void serial_console_write(struct console *co, const char *s, | |
1829 | unsigned count) | |
1830 | { | |
1831 | unsigned short intena = custom.intenar; | |
1832 | ||
1833 | custom.intena = IF_TBE; | |
1834 | ||
1835 | while (count--) { | |
1836 | if (*s == '\n') | |
1837 | amiga_serial_putc('\r'); | |
1838 | amiga_serial_putc(*s++); | |
1839 | } | |
1840 | ||
1841 | custom.intena = IF_SETCLR | (intena & IF_TBE); | |
1842 | } | |
1843 | ||
1844 | static struct tty_driver *serial_console_device(struct console *c, int *index) | |
1845 | { | |
1846 | *index = 0; | |
1847 | return serial_driver; | |
1848 | } | |
1849 | ||
1850 | static struct console sercons = { | |
1851 | .name = "ttyS", | |
1852 | .write = serial_console_write, | |
1853 | .device = serial_console_device, | |
1854 | .flags = CON_PRINTBUFFER, | |
1855 | .index = -1, | |
1856 | }; | |
1857 | ||
1858 | /* | |
1859 | * Register console. | |
1860 | */ | |
1861 | static int __init amiserial_console_init(void) | |
1862 | { | |
3dcf344b GU |
1863 | if (!MACH_IS_AMIGA) |
1864 | return -ENODEV; | |
1865 | ||
1da177e4 LT |
1866 | register_console(&sercons); |
1867 | return 0; | |
1868 | } | |
1869 | console_initcall(amiserial_console_init); | |
d1a35e4d GU |
1870 | |
1871 | #endif /* CONFIG_SERIAL_CONSOLE && !MODULE */ | |
1da177e4 LT |
1872 | |
1873 | MODULE_LICENSE("GPL"); | |
826e8c8c | 1874 | MODULE_ALIAS("platform:amiga-serial"); |