Commit | Line | Data |
---|---|---|
2ac4ad2a VG |
1 | /* |
2 | * ARC On-Chip(fpga) UART Driver | |
3 | * | |
4 | * Copyright (C) 2010-2012 Synopsys, Inc. (www.synopsys.com) | |
5 | * | |
6 | * This program is free software; you can redistribute it and/or modify | |
7 | * it under the terms of the GNU General Public License version 2 as | |
8 | * published by the Free Software Foundation. | |
9 | * | |
10 | * vineetg: July 10th 2012 | |
11 | * -Decoupled the driver from arch/arc | |
12 | * +Using platform_get_resource() for irq/membase (thx to bfin_uart.c) | |
13 | * +Using early_platform_xxx() for early console (thx to mach-shmobile/xxx) | |
14 | * | |
15 | * Vineetg: Aug 21st 2010 | |
16 | * -Is uart_tx_stopped() not done in tty write path as it has already been | |
17 | * taken care of, in serial core | |
18 | * | |
19 | * Vineetg: Aug 18th 2010 | |
20 | * -New Serial Core based ARC UART driver | |
21 | * -Derived largely from blackfin driver albiet with some major tweaks | |
22 | * | |
23 | * TODO: | |
24 | * -check if sysreq works | |
25 | */ | |
26 | ||
27 | #if defined(CONFIG_SERIAL_ARC_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) | |
28 | #define SUPPORT_SYSRQ | |
29 | #endif | |
30 | ||
31 | #include <linux/module.h> | |
32 | #include <linux/serial.h> | |
33 | #include <linux/console.h> | |
34 | #include <linux/sysrq.h> | |
35 | #include <linux/platform_device.h> | |
36 | #include <linux/tty.h> | |
37 | #include <linux/tty_flip.h> | |
38 | #include <linux/serial_core.h> | |
39 | #include <linux/io.h> | |
ea28fd56 VG |
40 | #include <linux/of.h> |
41 | #include <linux/of_platform.h> | |
2ac4ad2a VG |
42 | |
43 | /************************************* | |
44 | * ARC UART Hardware Specs | |
45 | ************************************/ | |
46 | #define ARC_UART_TX_FIFO_SIZE 1 | |
47 | ||
48 | /* | |
49 | * UART Register set (this is not a Standards Compliant IP) | |
50 | * Also each reg is Word aligned, but only 8 bits wide | |
51 | */ | |
52 | #define R_ID0 0 | |
53 | #define R_ID1 4 | |
54 | #define R_ID2 8 | |
55 | #define R_ID3 12 | |
56 | #define R_DATA 16 | |
57 | #define R_STS 20 | |
58 | #define R_BAUDL 24 | |
59 | #define R_BAUDH 28 | |
60 | ||
61 | /* Bits for UART Status Reg (R/W) */ | |
62 | #define RXIENB 0x04 /* Receive Interrupt Enable */ | |
63 | #define TXIENB 0x40 /* Transmit Interrupt Enable */ | |
64 | ||
65 | #define RXEMPTY 0x20 /* Receive FIFO Empty: No char receivede */ | |
66 | #define TXEMPTY 0x80 /* Transmit FIFO Empty, thus char can be written into */ | |
67 | ||
68 | #define RXFULL 0x08 /* Receive FIFO full */ | |
69 | #define RXFULL1 0x10 /* Receive FIFO has space for 1 char (tot space=4) */ | |
70 | ||
71 | #define RXFERR 0x01 /* Frame Error: Stop Bit not detected */ | |
72 | #define RXOERR 0x02 /* OverFlow Err: Char recv but RXFULL still set */ | |
73 | ||
74 | /* Uart bit fiddling helpers: lowest level */ | |
12d15e6f | 75 | #define RBASE(port, reg) (port->membase + reg) |
2ac4ad2a VG |
76 | #define UART_REG_SET(u, r, v) writeb((v), RBASE(u, r)) |
77 | #define UART_REG_GET(u, r) readb(RBASE(u, r)) | |
78 | ||
79 | #define UART_REG_OR(u, r, v) UART_REG_SET(u, r, UART_REG_GET(u, r) | (v)) | |
80 | #define UART_REG_CLR(u, r, v) UART_REG_SET(u, r, UART_REG_GET(u, r) & ~(v)) | |
81 | ||
82 | /* Uart bit fiddling helpers: API level */ | |
83 | #define UART_SET_DATA(uart, val) UART_REG_SET(uart, R_DATA, val) | |
84 | #define UART_GET_DATA(uart) UART_REG_GET(uart, R_DATA) | |
85 | ||
86 | #define UART_SET_BAUDH(uart, val) UART_REG_SET(uart, R_BAUDH, val) | |
87 | #define UART_SET_BAUDL(uart, val) UART_REG_SET(uart, R_BAUDL, val) | |
88 | ||
89 | #define UART_CLR_STATUS(uart, val) UART_REG_CLR(uart, R_STS, val) | |
90 | #define UART_GET_STATUS(uart) UART_REG_GET(uart, R_STS) | |
91 | ||
92 | #define UART_ALL_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, RXIENB|TXIENB) | |
93 | #define UART_RX_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, RXIENB) | |
94 | #define UART_TX_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, TXIENB) | |
95 | ||
96 | #define UART_ALL_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, RXIENB|TXIENB) | |
97 | #define UART_RX_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, RXIENB) | |
98 | #define UART_TX_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, TXIENB) | |
99 | ||
100 | #define ARC_SERIAL_DEV_NAME "ttyARC" | |
101 | ||
102 | struct arc_uart_port { | |
103 | struct uart_port port; | |
104 | unsigned long baud; | |
2ac4ad2a VG |
105 | }; |
106 | ||
107 | #define to_arc_port(uport) container_of(uport, struct arc_uart_port, port) | |
108 | ||
109 | static struct arc_uart_port arc_uart_ports[CONFIG_SERIAL_ARC_NR_PORTS]; | |
110 | ||
111 | #ifdef CONFIG_SERIAL_ARC_CONSOLE | |
112 | static struct console arc_console; | |
113 | #endif | |
114 | ||
115 | #define DRIVER_NAME "arc-uart" | |
116 | ||
117 | static struct uart_driver arc_uart_driver = { | |
118 | .owner = THIS_MODULE, | |
119 | .driver_name = DRIVER_NAME, | |
120 | .dev_name = ARC_SERIAL_DEV_NAME, | |
121 | .major = 0, | |
122 | .minor = 0, | |
123 | .nr = CONFIG_SERIAL_ARC_NR_PORTS, | |
124 | #ifdef CONFIG_SERIAL_ARC_CONSOLE | |
125 | .cons = &arc_console, | |
126 | #endif | |
127 | }; | |
128 | ||
129 | static void arc_serial_stop_rx(struct uart_port *port) | |
130 | { | |
12d15e6f | 131 | UART_RX_IRQ_DISABLE(port); |
2ac4ad2a VG |
132 | } |
133 | ||
134 | static void arc_serial_stop_tx(struct uart_port *port) | |
135 | { | |
12d15e6f | 136 | while (!(UART_GET_STATUS(port) & TXEMPTY)) |
2ac4ad2a VG |
137 | cpu_relax(); |
138 | ||
12d15e6f | 139 | UART_TX_IRQ_DISABLE(port); |
2ac4ad2a VG |
140 | } |
141 | ||
142 | /* | |
143 | * Return TIOCSER_TEMT when transmitter is not busy. | |
144 | */ | |
145 | static unsigned int arc_serial_tx_empty(struct uart_port *port) | |
146 | { | |
2ac4ad2a VG |
147 | unsigned int stat; |
148 | ||
12d15e6f | 149 | stat = UART_GET_STATUS(port); |
2ac4ad2a VG |
150 | if (stat & TXEMPTY) |
151 | return TIOCSER_TEMT; | |
152 | ||
153 | return 0; | |
154 | } | |
155 | ||
156 | /* | |
157 | * Driver internal routine, used by both tty(serial core) as well as tx-isr | |
158 | * -Called under spinlock in either cases | |
ee797069 | 159 | * -also tty->stopped has already been checked |
2ac4ad2a VG |
160 | * = by uart_start( ) before calling us |
161 | * = tx_ist checks that too before calling | |
162 | */ | |
12d15e6f | 163 | static void arc_serial_tx_chars(struct uart_port *port) |
2ac4ad2a | 164 | { |
12d15e6f | 165 | struct circ_buf *xmit = &port->state->xmit; |
2ac4ad2a VG |
166 | int sent = 0; |
167 | unsigned char ch; | |
168 | ||
12d15e6f VG |
169 | if (unlikely(port->x_char)) { |
170 | UART_SET_DATA(port, port->x_char); | |
171 | port->icount.tx++; | |
172 | port->x_char = 0; | |
2ac4ad2a VG |
173 | sent = 1; |
174 | } else if (xmit->tail != xmit->head) { /* TODO: uart_circ_empty */ | |
175 | ch = xmit->buf[xmit->tail]; | |
176 | xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); | |
12d15e6f VG |
177 | port->icount.tx++; |
178 | while (!(UART_GET_STATUS(port) & TXEMPTY)) | |
2ac4ad2a | 179 | cpu_relax(); |
12d15e6f | 180 | UART_SET_DATA(port, ch); |
2ac4ad2a VG |
181 | sent = 1; |
182 | } | |
183 | ||
184 | /* | |
185 | * If num chars in xmit buffer are too few, ask tty layer for more. | |
186 | * By Hard ISR to schedule processing in software interrupt part | |
187 | */ | |
188 | if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) | |
12d15e6f | 189 | uart_write_wakeup(port); |
2ac4ad2a VG |
190 | |
191 | if (sent) | |
12d15e6f | 192 | UART_TX_IRQ_ENABLE(port); |
2ac4ad2a VG |
193 | } |
194 | ||
195 | /* | |
196 | * port is locked and interrupts are disabled | |
197 | * uart_start( ) calls us under the port spinlock irqsave | |
198 | */ | |
199 | static void arc_serial_start_tx(struct uart_port *port) | |
200 | { | |
12d15e6f | 201 | arc_serial_tx_chars(port); |
2ac4ad2a VG |
202 | } |
203 | ||
12d15e6f | 204 | static void arc_serial_rx_chars(struct uart_port *port, unsigned int status) |
2ac4ad2a | 205 | { |
5284eba7 | 206 | unsigned int ch, flg = 0; |
2ac4ad2a | 207 | |
2ac4ad2a VG |
208 | /* |
209 | * UART has 4 deep RX-FIFO. Driver's recongnition of this fact | |
210 | * is very subtle. Here's how ... | |
211 | * Upon getting a RX-Intr, such that RX-EMPTY=0, meaning data available, | |
212 | * driver reads the DATA Reg and keeps doing that in a loop, until | |
213 | * RX-EMPTY=1. Multiple chars being avail, with a single Interrupt, | |
214 | * before RX-EMPTY=0, implies some sort of buffering going on in the | |
215 | * controller, which is indeed the Rx-FIFO. | |
216 | */ | |
5284eba7 VG |
217 | do { |
218 | /* | |
219 | * This could be an Rx Intr for err (no data), | |
220 | * so check err and clear that Intr first | |
221 | */ | |
2ac4ad2a VG |
222 | if (unlikely(status & (RXOERR | RXFERR))) { |
223 | if (status & RXOERR) { | |
12d15e6f | 224 | port->icount.overrun++; |
2ac4ad2a | 225 | flg = TTY_OVERRUN; |
12d15e6f | 226 | UART_CLR_STATUS(port, RXOERR); |
2ac4ad2a VG |
227 | } |
228 | ||
229 | if (status & RXFERR) { | |
12d15e6f | 230 | port->icount.frame++; |
2ac4ad2a | 231 | flg = TTY_FRAME; |
12d15e6f | 232 | UART_CLR_STATUS(port, RXFERR); |
2ac4ad2a VG |
233 | } |
234 | } else | |
235 | flg = TTY_NORMAL; | |
236 | ||
5284eba7 VG |
237 | if (status & RXEMPTY) |
238 | continue; | |
239 | ||
12d15e6f VG |
240 | ch = UART_GET_DATA(port); |
241 | port->icount.rx++; | |
5284eba7 | 242 | |
12d15e6f VG |
243 | if (!(uart_handle_sysrq_char(port, ch))) |
244 | uart_insert_char(port, status, RXOERR, ch, flg); | |
2ac4ad2a | 245 | |
12d15e6f VG |
246 | spin_unlock(&port->lock); |
247 | tty_flip_buffer_push(&port->state->port); | |
248 | spin_lock(&port->lock); | |
249 | } while (!((status = UART_GET_STATUS(port)) & RXEMPTY)); | |
2ac4ad2a VG |
250 | } |
251 | ||
252 | /* | |
253 | * A note on the Interrupt handling state machine of this driver | |
254 | * | |
255 | * kernel printk writes funnel thru the console driver framework and in order | |
256 | * to keep things simple as well as efficient, it writes to UART in polled | |
257 | * mode, in one shot, and exits. | |
258 | * | |
259 | * OTOH, Userland output (via tty layer), uses interrupt based writes as there | |
260 | * can be undeterministic delay between char writes. | |
261 | * | |
262 | * Thus Rx-interrupts are always enabled, while tx-interrupts are by default | |
263 | * disabled. | |
264 | * | |
265 | * When tty has some data to send out, serial core calls driver's start_tx | |
266 | * which | |
267 | * -checks-if-tty-buffer-has-char-to-send | |
268 | * -writes-data-to-uart | |
269 | * -enable-tx-intr | |
270 | * | |
271 | * Once data bits are pushed out, controller raises the Tx-room-avail-Interrupt. | |
272 | * The first thing Tx ISR does is disable further Tx interrupts (as this could | |
273 | * be the last char to send, before settling down into the quiet polled mode). | |
274 | * It then calls the exact routine used by tty layer write to send out any | |
275 | * more char in tty buffer. In case of sending, it re-enables Tx-intr. In case | |
276 | * of no data, it remains disabled. | |
277 | * This is how the transmit state machine is dynamically switched on/off | |
278 | */ | |
279 | ||
280 | static irqreturn_t arc_serial_isr(int irq, void *dev_id) | |
281 | { | |
12d15e6f | 282 | struct uart_port *port = dev_id; |
2ac4ad2a VG |
283 | unsigned int status; |
284 | ||
12d15e6f | 285 | status = UART_GET_STATUS(port); |
2ac4ad2a VG |
286 | |
287 | /* | |
288 | * Single IRQ for both Rx (data available) Tx (room available) Interrupt | |
289 | * notifications from the UART Controller. | |
290 | * To demultiplex between the two, we check the relevant bits | |
291 | */ | |
5284eba7 | 292 | if (status & RXIENB) { |
2ac4ad2a VG |
293 | |
294 | /* already in ISR, no need of xx_irqsave */ | |
12d15e6f VG |
295 | spin_lock(&port->lock); |
296 | arc_serial_rx_chars(port, status); | |
297 | spin_unlock(&port->lock); | |
2ac4ad2a VG |
298 | } |
299 | ||
300 | if ((status & TXIENB) && (status & TXEMPTY)) { | |
301 | ||
302 | /* Unconditionally disable further Tx-Interrupts. | |
303 | * will be enabled by tx_chars() if needed. | |
304 | */ | |
12d15e6f | 305 | UART_TX_IRQ_DISABLE(port); |
2ac4ad2a | 306 | |
12d15e6f | 307 | spin_lock(&port->lock); |
2ac4ad2a | 308 | |
12d15e6f VG |
309 | if (!uart_tx_stopped(port)) |
310 | arc_serial_tx_chars(port); | |
2ac4ad2a | 311 | |
12d15e6f | 312 | spin_unlock(&port->lock); |
2ac4ad2a VG |
313 | } |
314 | ||
315 | return IRQ_HANDLED; | |
316 | } | |
317 | ||
318 | static unsigned int arc_serial_get_mctrl(struct uart_port *port) | |
319 | { | |
320 | /* | |
321 | * Pretend we have a Modem status reg and following bits are | |
322 | * always set, to satify the serial core state machine | |
323 | * (DSR) Data Set Ready | |
324 | * (CTS) Clear To Send | |
325 | * (CAR) Carrier Detect | |
326 | */ | |
327 | return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; | |
328 | } | |
329 | ||
330 | static void arc_serial_set_mctrl(struct uart_port *port, unsigned int mctrl) | |
331 | { | |
332 | /* MCR not present */ | |
333 | } | |
334 | ||
2ac4ad2a VG |
335 | static void arc_serial_break_ctl(struct uart_port *port, int break_state) |
336 | { | |
337 | /* ARC UART doesn't support sending Break signal */ | |
338 | } | |
339 | ||
340 | static int arc_serial_startup(struct uart_port *port) | |
341 | { | |
2ac4ad2a | 342 | /* Before we hook up the ISR, Disable all UART Interrupts */ |
12d15e6f | 343 | UART_ALL_IRQ_DISABLE(port); |
2ac4ad2a | 344 | |
12d15e6f VG |
345 | if (request_irq(port->irq, arc_serial_isr, 0, "arc uart rx-tx", port)) { |
346 | dev_warn(port->dev, "Unable to attach ARC UART intr\n"); | |
2ac4ad2a VG |
347 | return -EBUSY; |
348 | } | |
349 | ||
12d15e6f | 350 | UART_RX_IRQ_ENABLE(port); /* Only Rx IRQ enabled to begin with */ |
2ac4ad2a VG |
351 | |
352 | return 0; | |
353 | } | |
354 | ||
355 | /* This is not really needed */ | |
356 | static void arc_serial_shutdown(struct uart_port *port) | |
357 | { | |
12d15e6f | 358 | free_irq(port->irq, port); |
2ac4ad2a VG |
359 | } |
360 | ||
361 | static void | |
362 | arc_serial_set_termios(struct uart_port *port, struct ktermios *new, | |
363 | struct ktermios *old) | |
364 | { | |
365 | struct arc_uart_port *uart = to_arc_port(port); | |
366 | unsigned int baud, uartl, uarth, hw_val; | |
367 | unsigned long flags; | |
368 | ||
369 | /* | |
370 | * Use the generic handler so that any specially encoded baud rates | |
371 | * such as SPD_xx flags or "%B0" can be handled | |
372 | * Max Baud I suppose will not be more than current 115K * 4 | |
373 | * Formula for ARC UART is: hw-val = ((CLK/(BAUD*4)) -1) | |
374 | * spread over two 8-bit registers | |
375 | */ | |
376 | baud = uart_get_baud_rate(port, new, old, 0, 460800); | |
377 | ||
378 | hw_val = port->uartclk / (uart->baud * 4) - 1; | |
379 | uartl = hw_val & 0xFF; | |
380 | uarth = (hw_val >> 8) & 0xFF; | |
381 | ||
2ac4ad2a VG |
382 | spin_lock_irqsave(&port->lock, flags); |
383 | ||
12d15e6f | 384 | UART_ALL_IRQ_DISABLE(port); |
2ac4ad2a | 385 | |
12d15e6f VG |
386 | UART_SET_BAUDL(port, uartl); |
387 | UART_SET_BAUDH(port, uarth); | |
2ac4ad2a | 388 | |
12d15e6f | 389 | UART_RX_IRQ_ENABLE(port); |
2ac4ad2a VG |
390 | |
391 | /* | |
392 | * UART doesn't support Parity/Hardware Flow Control; | |
393 | * Only supports 8N1 character size | |
394 | */ | |
395 | new->c_cflag &= ~(CMSPAR|CRTSCTS|CSIZE); | |
396 | new->c_cflag |= CS8; | |
397 | ||
398 | if (old) | |
399 | tty_termios_copy_hw(new, old); | |
400 | ||
401 | /* Don't rewrite B0 */ | |
402 | if (tty_termios_baud_rate(new)) | |
403 | tty_termios_encode_baud_rate(new, baud, baud); | |
404 | ||
405 | uart_update_timeout(port, new->c_cflag, baud); | |
406 | ||
407 | spin_unlock_irqrestore(&port->lock, flags); | |
408 | } | |
409 | ||
410 | static const char *arc_serial_type(struct uart_port *port) | |
411 | { | |
12d15e6f | 412 | return port->type == PORT_ARC ? DRIVER_NAME : NULL; |
2ac4ad2a VG |
413 | } |
414 | ||
415 | static void arc_serial_release_port(struct uart_port *port) | |
416 | { | |
417 | } | |
418 | ||
419 | static int arc_serial_request_port(struct uart_port *port) | |
420 | { | |
421 | return 0; | |
422 | } | |
423 | ||
424 | /* | |
425 | * Verify the new serial_struct (for TIOCSSERIAL). | |
426 | */ | |
427 | static int | |
428 | arc_serial_verify_port(struct uart_port *port, struct serial_struct *ser) | |
429 | { | |
430 | if (port->type != PORT_UNKNOWN && ser->type != PORT_ARC) | |
431 | return -EINVAL; | |
432 | ||
433 | return 0; | |
434 | } | |
435 | ||
436 | /* | |
437 | * Configure/autoconfigure the port. | |
438 | */ | |
439 | static void arc_serial_config_port(struct uart_port *port, int flags) | |
440 | { | |
2ac4ad2a | 441 | if (flags & UART_CONFIG_TYPE) |
12d15e6f | 442 | port->type = PORT_ARC; |
2ac4ad2a VG |
443 | } |
444 | ||
445 | #if defined(CONFIG_CONSOLE_POLL) || defined(CONFIG_SERIAL_ARC_CONSOLE) | |
446 | ||
3bce1b70 | 447 | static void arc_serial_poll_putchar(struct uart_port *port, int chr) |
2ac4ad2a | 448 | { |
12d15e6f | 449 | while (!(UART_GET_STATUS(port) & TXEMPTY)) |
2ac4ad2a VG |
450 | cpu_relax(); |
451 | ||
12d15e6f | 452 | UART_SET_DATA(port, (unsigned char)chr); |
2ac4ad2a VG |
453 | } |
454 | #endif | |
455 | ||
456 | #ifdef CONFIG_CONSOLE_POLL | |
457 | static int arc_serial_poll_getchar(struct uart_port *port) | |
458 | { | |
2ac4ad2a VG |
459 | unsigned char chr; |
460 | ||
12d15e6f | 461 | while (!(UART_GET_STATUS(port) & RXEMPTY)) |
2ac4ad2a VG |
462 | cpu_relax(); |
463 | ||
12d15e6f | 464 | chr = UART_GET_DATA(port); |
2ac4ad2a VG |
465 | return chr; |
466 | } | |
467 | #endif | |
468 | ||
469 | static struct uart_ops arc_serial_pops = { | |
470 | .tx_empty = arc_serial_tx_empty, | |
471 | .set_mctrl = arc_serial_set_mctrl, | |
472 | .get_mctrl = arc_serial_get_mctrl, | |
473 | .stop_tx = arc_serial_stop_tx, | |
474 | .start_tx = arc_serial_start_tx, | |
475 | .stop_rx = arc_serial_stop_rx, | |
2ac4ad2a VG |
476 | .break_ctl = arc_serial_break_ctl, |
477 | .startup = arc_serial_startup, | |
478 | .shutdown = arc_serial_shutdown, | |
479 | .set_termios = arc_serial_set_termios, | |
480 | .type = arc_serial_type, | |
481 | .release_port = arc_serial_release_port, | |
482 | .request_port = arc_serial_request_port, | |
483 | .config_port = arc_serial_config_port, | |
484 | .verify_port = arc_serial_verify_port, | |
485 | #ifdef CONFIG_CONSOLE_POLL | |
486 | .poll_put_char = arc_serial_poll_putchar, | |
487 | .poll_get_char = arc_serial_poll_getchar, | |
488 | #endif | |
489 | }; | |
490 | ||
9671f099 | 491 | static int |
026bb292 | 492 | arc_uart_init_one(struct platform_device *pdev, int dev_id) |
2ac4ad2a VG |
493 | { |
494 | struct resource *res, *res2; | |
026bb292 | 495 | struct arc_uart_port *uart = &arc_uart_ports[dev_id]; |
12d15e6f | 496 | struct uart_port *port = &uart->port; |
2ac4ad2a | 497 | |
2e6fb7cb VG |
498 | struct device_node *np = pdev->dev.of_node; |
499 | u32 val; | |
d6c0d06b | 500 | |
2e6fb7cb VG |
501 | if (of_property_read_u32(np, "clock-frequency", &val)) { |
502 | dev_err(&pdev->dev, "clock-frequency property NOTset\n"); | |
503 | return -EINVAL; | |
ea28fd56 | 504 | } |
2e6fb7cb VG |
505 | port->uartclk = val; |
506 | ||
507 | if (of_property_read_u32(np, "current-speed", &val)) { | |
508 | dev_err(&pdev->dev, "current-speed property NOT set\n"); | |
509 | return -EINVAL; | |
510 | } | |
511 | uart->baud = val; | |
2ac4ad2a VG |
512 | |
513 | res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
514 | if (!res) | |
515 | return -ENODEV; | |
516 | ||
517 | res2 = platform_get_resource(pdev, IORESOURCE_IRQ, 0); | |
518 | if (!res2) | |
519 | return -ENODEV; | |
520 | ||
12d15e6f VG |
521 | port->mapbase = res->start; |
522 | port->membase = ioremap_nocache(res->start, resource_size(res)); | |
523 | if (!port->membase) | |
2ac4ad2a VG |
524 | /* No point of dev_err since UART itself is hosed here */ |
525 | return -ENXIO; | |
526 | ||
12d15e6f VG |
527 | port->irq = res2->start; |
528 | port->dev = &pdev->dev; | |
529 | port->iotype = UPIO_MEM; | |
530 | port->flags = UPF_BOOT_AUTOCONF; | |
531 | port->line = dev_id; | |
532 | port->ops = &arc_serial_pops; | |
2ac4ad2a | 533 | |
12d15e6f | 534 | port->fifosize = ARC_UART_TX_FIFO_SIZE; |
2ac4ad2a VG |
535 | |
536 | /* | |
537 | * uart_insert_char( ) uses it in decideding whether to ignore a | |
538 | * char or not. Explicitly setting it here, removes the subtelty | |
539 | */ | |
12d15e6f | 540 | port->ignore_status_mask = 0; |
2ac4ad2a | 541 | |
2ac4ad2a VG |
542 | return 0; |
543 | } | |
544 | ||
545 | #ifdef CONFIG_SERIAL_ARC_CONSOLE | |
546 | ||
9671f099 | 547 | static int arc_serial_console_setup(struct console *co, char *options) |
2ac4ad2a VG |
548 | { |
549 | struct uart_port *port; | |
550 | int baud = 115200; | |
551 | int bits = 8; | |
552 | int parity = 'n'; | |
553 | int flow = 'n'; | |
554 | ||
555 | if (co->index < 0 || co->index >= CONFIG_SERIAL_ARC_NR_PORTS) | |
556 | return -ENODEV; | |
557 | ||
558 | /* | |
559 | * The uart port backing the console (e.g. ttyARC1) might not have been | |
560 | * init yet. If so, defer the console setup to after the port. | |
561 | */ | |
562 | port = &arc_uart_ports[co->index].port; | |
563 | if (!port->membase) | |
564 | return -ENODEV; | |
565 | ||
566 | if (options) | |
567 | uart_parse_options(options, &baud, &parity, &bits, &flow); | |
568 | ||
569 | /* | |
570 | * Serial core will call port->ops->set_termios( ) | |
571 | * which will set the baud reg | |
572 | */ | |
573 | return uart_set_options(port, co, baud, parity, bits, flow); | |
574 | } | |
575 | ||
2ac4ad2a VG |
576 | /* |
577 | * Interrupts are disabled on entering | |
578 | */ | |
579 | static void arc_serial_console_write(struct console *co, const char *s, | |
580 | unsigned int count) | |
581 | { | |
582 | struct uart_port *port = &arc_uart_ports[co->index].port; | |
583 | unsigned long flags; | |
584 | ||
585 | spin_lock_irqsave(&port->lock, flags); | |
3bce1b70 | 586 | uart_console_write(port, s, count, arc_serial_poll_putchar); |
2ac4ad2a VG |
587 | spin_unlock_irqrestore(&port->lock, flags); |
588 | } | |
589 | ||
590 | static struct console arc_console = { | |
591 | .name = ARC_SERIAL_DEV_NAME, | |
592 | .write = arc_serial_console_write, | |
593 | .device = uart_console_device, | |
594 | .setup = arc_serial_console_setup, | |
595 | .flags = CON_PRINTBUFFER, | |
596 | .index = -1, | |
597 | .data = &arc_uart_driver | |
598 | }; | |
599 | ||
27cfe4ec VG |
600 | static __init void arc_early_serial_write(struct console *con, const char *s, |
601 | unsigned int n) | |
602 | { | |
603 | struct earlycon_device *dev = con->data; | |
604 | ||
605 | uart_console_write(&dev->port, s, n, arc_serial_poll_putchar); | |
606 | } | |
607 | ||
608 | static int __init arc_early_console_setup(struct earlycon_device *dev, | |
609 | const char *opt) | |
610 | { | |
611 | struct uart_port *port = &dev->port; | |
612 | unsigned int l, h, hw_val; | |
613 | ||
614 | if (!dev->port.membase) | |
615 | return -ENODEV; | |
616 | ||
617 | hw_val = port->uartclk / (dev->baud * 4) - 1; | |
618 | l = hw_val & 0xFF; | |
619 | h = (hw_val >> 8) & 0xFF; | |
620 | ||
621 | UART_SET_BAUDL(port, l); | |
622 | UART_SET_BAUDH(port, h); | |
623 | ||
624 | dev->con->write = arc_early_serial_write; | |
625 | return 0; | |
626 | } | |
627 | EARLYCON_DECLARE(arc_uart, arc_early_console_setup); | |
628 | ||
2ac4ad2a VG |
629 | #endif /* CONFIG_SERIAL_ARC_CONSOLE */ |
630 | ||
9671f099 | 631 | static int arc_serial_probe(struct platform_device *pdev) |
2ac4ad2a | 632 | { |
026bb292 | 633 | int rc, dev_id; |
ea28fd56 VG |
634 | struct device_node *np = pdev->dev.of_node; |
635 | ||
636 | /* no device tree device */ | |
637 | if (!np) | |
638 | return -ENODEV; | |
639 | ||
640 | dev_id = of_alias_get_id(np, "serial"); | |
11c62d4f VG |
641 | if (dev_id < 0) |
642 | dev_id = 0; | |
2ac4ad2a | 643 | |
026bb292 | 644 | rc = arc_uart_init_one(pdev, dev_id); |
2ac4ad2a VG |
645 | if (rc) |
646 | return rc; | |
647 | ||
026bb292 VG |
648 | rc = uart_add_one_port(&arc_uart_driver, &arc_uart_ports[dev_id].port); |
649 | return rc; | |
2ac4ad2a VG |
650 | } |
651 | ||
ae8d8a14 | 652 | static int arc_serial_remove(struct platform_device *pdev) |
2ac4ad2a VG |
653 | { |
654 | /* This will never be called */ | |
655 | return 0; | |
656 | } | |
657 | ||
ea28fd56 VG |
658 | static const struct of_device_id arc_uart_dt_ids[] = { |
659 | { .compatible = "snps,arc-uart" }, | |
660 | { /* Sentinel */ } | |
661 | }; | |
662 | MODULE_DEVICE_TABLE(of, arc_uart_dt_ids); | |
663 | ||
2ac4ad2a VG |
664 | static struct platform_driver arc_platform_driver = { |
665 | .probe = arc_serial_probe, | |
2d47b716 | 666 | .remove = arc_serial_remove, |
2ac4ad2a VG |
667 | .driver = { |
668 | .name = DRIVER_NAME, | |
669 | .owner = THIS_MODULE, | |
ea28fd56 | 670 | .of_match_table = arc_uart_dt_ids, |
2ac4ad2a VG |
671 | }, |
672 | }; | |
673 | ||
2ac4ad2a VG |
674 | static int __init arc_serial_init(void) |
675 | { | |
676 | int ret; | |
677 | ||
678 | ret = uart_register_driver(&arc_uart_driver); | |
679 | if (ret) | |
680 | return ret; | |
681 | ||
682 | ret = platform_driver_register(&arc_platform_driver); | |
683 | if (ret) | |
684 | uart_unregister_driver(&arc_uart_driver); | |
685 | ||
686 | return ret; | |
687 | } | |
688 | ||
689 | static void __exit arc_serial_exit(void) | |
690 | { | |
691 | platform_driver_unregister(&arc_platform_driver); | |
692 | uart_unregister_driver(&arc_uart_driver); | |
693 | } | |
694 | ||
695 | module_init(arc_serial_init); | |
696 | module_exit(arc_serial_exit); | |
697 | ||
698 | MODULE_LICENSE("GPL"); | |
d5a12ea7 | 699 | MODULE_ALIAS("platform:" DRIVER_NAME); |
2ac4ad2a VG |
700 | MODULE_AUTHOR("Vineet Gupta"); |
701 | MODULE_DESCRIPTION("ARC(Synopsys) On-Chip(fpga) serial driver"); |