Commit | Line | Data |
---|---|---|
d843fc6e FT |
1 | /* |
2 | * mfd.c: driver for High Speed UART device of Intel Medfield platform | |
3 | * | |
4 | * Refer pxa.c, 8250.c and some other drivers in drivers/serial/ | |
5 | * | |
06c77e21 | 6 | * (C) Copyright 2010 Intel Corporation |
d843fc6e FT |
7 | * |
8 | * This program is free software; you can redistribute it and/or | |
9 | * modify it under the terms of the GNU General Public License | |
10 | * as published by the Free Software Foundation; version 2 | |
11 | * of the License. | |
12 | */ | |
13 | ||
d843fc6e | 14 | /* Notes: |
06c77e21 FT |
15 | * 1. DMA channel allocation: 0/1 channel are assigned to port 0, |
16 | * 2/3 chan to port 1, 4/5 chan to port 3. Even number chans | |
17 | * are used for RX, odd chans for TX | |
d843fc6e | 18 | * |
085a4f75 | 19 | * 2. The RI/DSR/DCD/DTR are not pinned out, DCD & DSR are always |
06c77e21 FT |
20 | * asserted, only when the HW is reset the DDCD and DDSR will |
21 | * be triggered | |
d843fc6e FT |
22 | */ |
23 | ||
24 | #include <linux/module.h> | |
25 | #include <linux/init.h> | |
26 | #include <linux/console.h> | |
27 | #include <linux/sysrq.h> | |
63d66cab | 28 | #include <linux/slab.h> |
d843fc6e FT |
29 | #include <linux/serial_reg.h> |
30 | #include <linux/circ_buf.h> | |
31 | #include <linux/delay.h> | |
32 | #include <linux/interrupt.h> | |
33 | #include <linux/tty.h> | |
34 | #include <linux/tty_flip.h> | |
35 | #include <linux/serial_core.h> | |
36 | #include <linux/serial_mfd.h> | |
37 | #include <linux/dma-mapping.h> | |
38 | #include <linux/pci.h> | |
50827fbd | 39 | #include <linux/nmi.h> |
d843fc6e FT |
40 | #include <linux/io.h> |
41 | #include <linux/debugfs.h> | |
88e5173f | 42 | #include <linux/pm_runtime.h> |
d843fc6e | 43 | |
d843fc6e FT |
44 | #define HSU_DMA_BUF_SIZE 2048 |
45 | ||
46 | #define chan_readl(chan, offset) readl(chan->reg + offset) | |
47 | #define chan_writel(chan, offset, val) writel(val, chan->reg + offset) | |
48 | ||
49 | #define mfd_readl(obj, offset) readl(obj->reg + offset) | |
50 | #define mfd_writel(obj, offset, val) writel(val, obj->reg + offset) | |
51 | ||
f023eab3 FT |
52 | static int hsu_dma_enable; |
53 | module_param(hsu_dma_enable, int, 0); | |
85ee7a1d JP |
54 | MODULE_PARM_DESC(hsu_dma_enable, |
55 | "It is a bitmap to set working mode, if bit[x] is 1, then port[x] will work in DMA mode, otherwise in PIO mode."); | |
f023eab3 | 56 | |
d843fc6e FT |
57 | struct hsu_dma_buffer { |
58 | u8 *buf; | |
59 | dma_addr_t dma_addr; | |
60 | u32 dma_size; | |
61 | u32 ofs; | |
62 | }; | |
63 | ||
64 | struct hsu_dma_chan { | |
65 | u32 id; | |
06c77e21 | 66 | enum dma_data_direction dirt; |
d843fc6e | 67 | struct uart_hsu_port *uport; |
669b7a09 | 68 | void __iomem *reg; |
d843fc6e FT |
69 | }; |
70 | ||
71 | struct uart_hsu_port { | |
72 | struct uart_port port; | |
73 | unsigned char ier; | |
74 | unsigned char lcr; | |
75 | unsigned char mcr; | |
76 | unsigned int lsr_break_flag; | |
77 | char name[12]; | |
78 | int index; | |
79 | struct device *dev; | |
80 | ||
81 | struct hsu_dma_chan *txc; | |
82 | struct hsu_dma_chan *rxc; | |
83 | struct hsu_dma_buffer txbuf; | |
84 | struct hsu_dma_buffer rxbuf; | |
85 | int use_dma; /* flag for DMA/PIO */ | |
86 | int running; | |
87 | int dma_tx_on; | |
88 | }; | |
89 | ||
90 | /* Top level data structure of HSU */ | |
91 | struct hsu_port { | |
d843fc6e FT |
92 | void __iomem *reg; |
93 | unsigned long paddr; | |
94 | unsigned long iolen; | |
95 | u32 irq; | |
96 | ||
97 | struct uart_hsu_port port[3]; | |
98 | struct hsu_dma_chan chans[10]; | |
99 | ||
d843fc6e | 100 | struct dentry *debugfs; |
d843fc6e FT |
101 | }; |
102 | ||
d843fc6e FT |
103 | static inline unsigned int serial_in(struct uart_hsu_port *up, int offset) |
104 | { | |
105 | unsigned int val; | |
106 | ||
107 | if (offset > UART_MSR) { | |
108 | offset <<= 2; | |
109 | val = readl(up->port.membase + offset); | |
110 | } else | |
111 | val = (unsigned int)readb(up->port.membase + offset); | |
112 | ||
113 | return val; | |
114 | } | |
115 | ||
116 | static inline void serial_out(struct uart_hsu_port *up, int offset, int value) | |
117 | { | |
118 | if (offset > UART_MSR) { | |
119 | offset <<= 2; | |
120 | writel(value, up->port.membase + offset); | |
121 | } else { | |
122 | unsigned char val = value & 0xff; | |
123 | writeb(val, up->port.membase + offset); | |
124 | } | |
125 | } | |
126 | ||
127 | #ifdef CONFIG_DEBUG_FS | |
128 | ||
129 | #define HSU_REGS_BUFSIZE 1024 | |
130 | ||
d843fc6e FT |
131 | |
132 | static ssize_t port_show_regs(struct file *file, char __user *user_buf, | |
133 | size_t count, loff_t *ppos) | |
134 | { | |
135 | struct uart_hsu_port *up = file->private_data; | |
136 | char *buf; | |
137 | u32 len = 0; | |
138 | ssize_t ret; | |
139 | ||
140 | buf = kzalloc(HSU_REGS_BUFSIZE, GFP_KERNEL); | |
141 | if (!buf) | |
142 | return 0; | |
143 | ||
144 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
145 | "MFD HSU port[%d] regs:\n", up->index); | |
146 | ||
147 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
148 | "=================================\n"); | |
149 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
150 | "IER: \t\t0x%08x\n", serial_in(up, UART_IER)); | |
151 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
152 | "IIR: \t\t0x%08x\n", serial_in(up, UART_IIR)); | |
153 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
154 | "LCR: \t\t0x%08x\n", serial_in(up, UART_LCR)); | |
155 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
156 | "MCR: \t\t0x%08x\n", serial_in(up, UART_MCR)); | |
157 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
158 | "LSR: \t\t0x%08x\n", serial_in(up, UART_LSR)); | |
159 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
160 | "MSR: \t\t0x%08x\n", serial_in(up, UART_MSR)); | |
161 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
162 | "FOR: \t\t0x%08x\n", serial_in(up, UART_FOR)); | |
163 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
164 | "PS: \t\t0x%08x\n", serial_in(up, UART_PS)); | |
165 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
166 | "MUL: \t\t0x%08x\n", serial_in(up, UART_MUL)); | |
167 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
168 | "DIV: \t\t0x%08x\n", serial_in(up, UART_DIV)); | |
169 | ||
a9589811 DC |
170 | if (len > HSU_REGS_BUFSIZE) |
171 | len = HSU_REGS_BUFSIZE; | |
172 | ||
d843fc6e FT |
173 | ret = simple_read_from_buffer(user_buf, count, ppos, buf, len); |
174 | kfree(buf); | |
175 | return ret; | |
176 | } | |
177 | ||
178 | static ssize_t dma_show_regs(struct file *file, char __user *user_buf, | |
179 | size_t count, loff_t *ppos) | |
180 | { | |
181 | struct hsu_dma_chan *chan = file->private_data; | |
182 | char *buf; | |
183 | u32 len = 0; | |
184 | ssize_t ret; | |
185 | ||
186 | buf = kzalloc(HSU_REGS_BUFSIZE, GFP_KERNEL); | |
187 | if (!buf) | |
188 | return 0; | |
189 | ||
190 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
191 | "MFD HSU DMA channel [%d] regs:\n", chan->id); | |
192 | ||
193 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
194 | "=================================\n"); | |
195 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
196 | "CR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_CR)); | |
197 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
198 | "DCR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_DCR)); | |
199 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
200 | "BSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_BSR)); | |
201 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
202 | "MOTSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_MOTSR)); | |
203 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
204 | "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D0SAR)); | |
205 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
206 | "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D0TSR)); | |
207 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
208 | "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D1SAR)); | |
209 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
210 | "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D1TSR)); | |
211 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
212 | "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D2SAR)); | |
213 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
214 | "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D2TSR)); | |
215 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
216 | "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D3SAR)); | |
217 | len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, | |
218 | "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D3TSR)); | |
219 | ||
a9589811 DC |
220 | if (len > HSU_REGS_BUFSIZE) |
221 | len = HSU_REGS_BUFSIZE; | |
222 | ||
d843fc6e FT |
223 | ret = simple_read_from_buffer(user_buf, count, ppos, buf, len); |
224 | kfree(buf); | |
225 | return ret; | |
226 | } | |
227 | ||
228 | static const struct file_operations port_regs_ops = { | |
229 | .owner = THIS_MODULE, | |
234e3405 | 230 | .open = simple_open, |
d843fc6e | 231 | .read = port_show_regs, |
6038f373 | 232 | .llseek = default_llseek, |
d843fc6e FT |
233 | }; |
234 | ||
235 | static const struct file_operations dma_regs_ops = { | |
236 | .owner = THIS_MODULE, | |
234e3405 | 237 | .open = simple_open, |
d843fc6e | 238 | .read = dma_show_regs, |
6038f373 | 239 | .llseek = default_llseek, |
d843fc6e FT |
240 | }; |
241 | ||
242 | static int hsu_debugfs_init(struct hsu_port *hsu) | |
243 | { | |
244 | int i; | |
245 | char name[32]; | |
246 | ||
247 | hsu->debugfs = debugfs_create_dir("hsu", NULL); | |
248 | if (!hsu->debugfs) | |
249 | return -ENOMEM; | |
250 | ||
251 | for (i = 0; i < 3; i++) { | |
252 | snprintf(name, sizeof(name), "port_%d_regs", i); | |
253 | debugfs_create_file(name, S_IFREG | S_IRUGO, | |
254 | hsu->debugfs, (void *)(&hsu->port[i]), &port_regs_ops); | |
255 | } | |
256 | ||
257 | for (i = 0; i < 6; i++) { | |
258 | snprintf(name, sizeof(name), "dma_chan_%d_regs", i); | |
259 | debugfs_create_file(name, S_IFREG | S_IRUGO, | |
260 | hsu->debugfs, (void *)&hsu->chans[i], &dma_regs_ops); | |
261 | } | |
262 | ||
263 | return 0; | |
264 | } | |
265 | ||
266 | static void hsu_debugfs_remove(struct hsu_port *hsu) | |
267 | { | |
268 | if (hsu->debugfs) | |
269 | debugfs_remove_recursive(hsu->debugfs); | |
270 | } | |
271 | ||
272 | #else | |
273 | static inline int hsu_debugfs_init(struct hsu_port *hsu) | |
274 | { | |
275 | return 0; | |
276 | } | |
277 | ||
278 | static inline void hsu_debugfs_remove(struct hsu_port *hsu) | |
279 | { | |
280 | } | |
281 | #endif /* CONFIG_DEBUG_FS */ | |
282 | ||
283 | static void serial_hsu_enable_ms(struct uart_port *port) | |
284 | { | |
285 | struct uart_hsu_port *up = | |
286 | container_of(port, struct uart_hsu_port, port); | |
287 | ||
288 | up->ier |= UART_IER_MSI; | |
289 | serial_out(up, UART_IER, up->ier); | |
290 | } | |
291 | ||
292 | void hsu_dma_tx(struct uart_hsu_port *up) | |
293 | { | |
294 | struct circ_buf *xmit = &up->port.state->xmit; | |
295 | struct hsu_dma_buffer *dbuf = &up->txbuf; | |
296 | int count; | |
297 | ||
298 | /* test_and_set_bit may be better, but anyway it's in lock protected mode */ | |
299 | if (up->dma_tx_on) | |
300 | return; | |
301 | ||
302 | /* Update the circ buf info */ | |
303 | xmit->tail += dbuf->ofs; | |
304 | xmit->tail &= UART_XMIT_SIZE - 1; | |
305 | ||
306 | up->port.icount.tx += dbuf->ofs; | |
307 | dbuf->ofs = 0; | |
308 | ||
309 | /* Disable the channel */ | |
310 | chan_writel(up->txc, HSU_CH_CR, 0x0); | |
311 | ||
312 | if (!uart_circ_empty(xmit) && !uart_tx_stopped(&up->port)) { | |
313 | dma_sync_single_for_device(up->port.dev, | |
314 | dbuf->dma_addr, | |
315 | dbuf->dma_size, | |
316 | DMA_TO_DEVICE); | |
317 | ||
318 | count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); | |
319 | dbuf->ofs = count; | |
320 | ||
321 | /* Reprogram the channel */ | |
322 | chan_writel(up->txc, HSU_CH_D0SAR, dbuf->dma_addr + xmit->tail); | |
323 | chan_writel(up->txc, HSU_CH_D0TSR, count); | |
324 | ||
325 | /* Reenable the channel */ | |
326 | chan_writel(up->txc, HSU_CH_DCR, 0x1 | |
327 | | (0x1 << 8) | |
328 | | (0x1 << 16) | |
329 | | (0x1 << 24)); | |
d843fc6e FT |
330 | up->dma_tx_on = 1; |
331 | chan_writel(up->txc, HSU_CH_CR, 0x1); | |
332 | } | |
333 | ||
334 | if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) | |
335 | uart_write_wakeup(&up->port); | |
336 | } | |
337 | ||
338 | /* The buffer is already cache coherent */ | |
339 | void hsu_dma_start_rx_chan(struct hsu_dma_chan *rxc, struct hsu_dma_buffer *dbuf) | |
340 | { | |
d843fc6e FT |
341 | dbuf->ofs = 0; |
342 | ||
343 | chan_writel(rxc, HSU_CH_BSR, 32); | |
344 | chan_writel(rxc, HSU_CH_MOTSR, 4); | |
345 | ||
346 | chan_writel(rxc, HSU_CH_D0SAR, dbuf->dma_addr); | |
347 | chan_writel(rxc, HSU_CH_D0TSR, dbuf->dma_size); | |
348 | chan_writel(rxc, HSU_CH_DCR, 0x1 | (0x1 << 8) | |
349 | | (0x1 << 16) | |
350 | | (0x1 << 24) /* timeout bit, see HSU Errata 1 */ | |
351 | ); | |
352 | chan_writel(rxc, HSU_CH_CR, 0x3); | |
353 | } | |
354 | ||
355 | /* Protected by spin_lock_irqsave(port->lock) */ | |
356 | static void serial_hsu_start_tx(struct uart_port *port) | |
357 | { | |
358 | struct uart_hsu_port *up = | |
359 | container_of(port, struct uart_hsu_port, port); | |
360 | ||
361 | if (up->use_dma) { | |
362 | hsu_dma_tx(up); | |
363 | } else if (!(up->ier & UART_IER_THRI)) { | |
364 | up->ier |= UART_IER_THRI; | |
365 | serial_out(up, UART_IER, up->ier); | |
366 | } | |
367 | } | |
368 | ||
369 | static void serial_hsu_stop_tx(struct uart_port *port) | |
370 | { | |
371 | struct uart_hsu_port *up = | |
372 | container_of(port, struct uart_hsu_port, port); | |
373 | struct hsu_dma_chan *txc = up->txc; | |
374 | ||
375 | if (up->use_dma) | |
376 | chan_writel(txc, HSU_CH_CR, 0x0); | |
377 | else if (up->ier & UART_IER_THRI) { | |
378 | up->ier &= ~UART_IER_THRI; | |
379 | serial_out(up, UART_IER, up->ier); | |
380 | } | |
381 | } | |
382 | ||
383 | /* This is always called in spinlock protected mode, so | |
384 | * modify timeout timer is safe here */ | |
385 | void hsu_dma_rx(struct uart_hsu_port *up, u32 int_sts) | |
386 | { | |
387 | struct hsu_dma_buffer *dbuf = &up->rxbuf; | |
388 | struct hsu_dma_chan *chan = up->rxc; | |
389 | struct uart_port *port = &up->port; | |
390 | struct tty_struct *tty = port->state->port.tty; | |
391 | int count; | |
392 | ||
393 | if (!tty) | |
394 | return; | |
395 | ||
396 | /* | |
06c77e21 | 397 | * First need to know how many is already transferred, |
d843fc6e FT |
398 | * then check if its a timeout DMA irq, and return |
399 | * the trail bytes out, push them up and reenable the | |
06c77e21 | 400 | * channel |
d843fc6e FT |
401 | */ |
402 | ||
06c77e21 | 403 | /* Timeout IRQ, need wait some time, see Errata 2 */ |
d843fc6e FT |
404 | if (int_sts & 0xf00) |
405 | udelay(2); | |
406 | ||
407 | /* Stop the channel */ | |
408 | chan_writel(chan, HSU_CH_CR, 0x0); | |
409 | ||
d843fc6e | 410 | count = chan_readl(chan, HSU_CH_D0SAR) - dbuf->dma_addr; |
669b7a09 | 411 | if (!count) { |
06c77e21 | 412 | /* Restart the channel before we leave */ |
669b7a09 | 413 | chan_writel(chan, HSU_CH_CR, 0x3); |
d843fc6e | 414 | return; |
669b7a09 | 415 | } |
d843fc6e FT |
416 | |
417 | dma_sync_single_for_cpu(port->dev, dbuf->dma_addr, | |
418 | dbuf->dma_size, DMA_FROM_DEVICE); | |
419 | ||
420 | /* | |
06c77e21 | 421 | * Head will only wrap around when we recycle |
d843fc6e FT |
422 | * the DMA buffer, and when that happens, we |
423 | * explicitly set tail to 0. So head will | |
424 | * always be greater than tail. | |
425 | */ | |
426 | tty_insert_flip_string(tty, dbuf->buf, count); | |
427 | port->icount.rx += count; | |
428 | ||
429 | dma_sync_single_for_device(up->port.dev, dbuf->dma_addr, | |
430 | dbuf->dma_size, DMA_FROM_DEVICE); | |
431 | ||
432 | /* Reprogram the channel */ | |
433 | chan_writel(chan, HSU_CH_D0SAR, dbuf->dma_addr); | |
434 | chan_writel(chan, HSU_CH_D0TSR, dbuf->dma_size); | |
435 | chan_writel(chan, HSU_CH_DCR, 0x1 | |
436 | | (0x1 << 8) | |
437 | | (0x1 << 16) | |
438 | | (0x1 << 24) /* timeout bit, see HSU Errata 1 */ | |
439 | ); | |
669b7a09 FT |
440 | tty_flip_buffer_push(tty); |
441 | ||
d843fc6e FT |
442 | chan_writel(chan, HSU_CH_CR, 0x3); |
443 | ||
d843fc6e FT |
444 | } |
445 | ||
446 | static void serial_hsu_stop_rx(struct uart_port *port) | |
447 | { | |
448 | struct uart_hsu_port *up = | |
449 | container_of(port, struct uart_hsu_port, port); | |
450 | struct hsu_dma_chan *chan = up->rxc; | |
451 | ||
452 | if (up->use_dma) | |
453 | chan_writel(chan, HSU_CH_CR, 0x2); | |
454 | else { | |
455 | up->ier &= ~UART_IER_RLSI; | |
456 | up->port.read_status_mask &= ~UART_LSR_DR; | |
457 | serial_out(up, UART_IER, up->ier); | |
458 | } | |
459 | } | |
460 | ||
d843fc6e FT |
461 | static inline void receive_chars(struct uart_hsu_port *up, int *status) |
462 | { | |
463 | struct tty_struct *tty = up->port.state->port.tty; | |
464 | unsigned int ch, flag; | |
465 | unsigned int max_count = 256; | |
466 | ||
467 | if (!tty) | |
468 | return; | |
469 | ||
470 | do { | |
471 | ch = serial_in(up, UART_RX); | |
472 | flag = TTY_NORMAL; | |
473 | up->port.icount.rx++; | |
474 | ||
475 | if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE | | |
476 | UART_LSR_FE | UART_LSR_OE))) { | |
477 | ||
478 | dev_warn(up->dev, "We really rush into ERR/BI case" | |
479 | "status = 0x%02x", *status); | |
480 | /* For statistics only */ | |
481 | if (*status & UART_LSR_BI) { | |
482 | *status &= ~(UART_LSR_FE | UART_LSR_PE); | |
483 | up->port.icount.brk++; | |
484 | /* | |
485 | * We do the SysRQ and SAK checking | |
486 | * here because otherwise the break | |
487 | * may get masked by ignore_status_mask | |
488 | * or read_status_mask. | |
489 | */ | |
490 | if (uart_handle_break(&up->port)) | |
491 | goto ignore_char; | |
492 | } else if (*status & UART_LSR_PE) | |
493 | up->port.icount.parity++; | |
494 | else if (*status & UART_LSR_FE) | |
495 | up->port.icount.frame++; | |
496 | if (*status & UART_LSR_OE) | |
497 | up->port.icount.overrun++; | |
498 | ||
499 | /* Mask off conditions which should be ignored. */ | |
500 | *status &= up->port.read_status_mask; | |
501 | ||
502 | #ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE | |
503 | if (up->port.cons && | |
504 | up->port.cons->index == up->port.line) { | |
505 | /* Recover the break flag from console xmit */ | |
506 | *status |= up->lsr_break_flag; | |
507 | up->lsr_break_flag = 0; | |
508 | } | |
509 | #endif | |
510 | if (*status & UART_LSR_BI) { | |
511 | flag = TTY_BREAK; | |
512 | } else if (*status & UART_LSR_PE) | |
513 | flag = TTY_PARITY; | |
514 | else if (*status & UART_LSR_FE) | |
515 | flag = TTY_FRAME; | |
516 | } | |
517 | ||
518 | if (uart_handle_sysrq_char(&up->port, ch)) | |
519 | goto ignore_char; | |
520 | ||
521 | uart_insert_char(&up->port, *status, UART_LSR_OE, ch, flag); | |
522 | ignore_char: | |
523 | *status = serial_in(up, UART_LSR); | |
524 | } while ((*status & UART_LSR_DR) && max_count--); | |
525 | tty_flip_buffer_push(tty); | |
526 | } | |
527 | ||
528 | static void transmit_chars(struct uart_hsu_port *up) | |
529 | { | |
530 | struct circ_buf *xmit = &up->port.state->xmit; | |
531 | int count; | |
d843fc6e FT |
532 | |
533 | if (up->port.x_char) { | |
534 | serial_out(up, UART_TX, up->port.x_char); | |
535 | up->port.icount.tx++; | |
536 | up->port.x_char = 0; | |
537 | return; | |
538 | } | |
539 | if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) { | |
540 | serial_hsu_stop_tx(&up->port); | |
541 | return; | |
542 | } | |
543 | ||
085a4f75 | 544 | /* The IRQ is for TX FIFO half-empty */ |
d843fc6e | 545 | count = up->port.fifosize / 2; |
085a4f75 | 546 | |
d843fc6e FT |
547 | do { |
548 | serial_out(up, UART_TX, xmit->buf[xmit->tail]); | |
549 | xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); | |
d843fc6e FT |
550 | |
551 | up->port.icount.tx++; | |
552 | if (uart_circ_empty(xmit)) | |
553 | break; | |
554 | } while (--count > 0); | |
555 | ||
556 | if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) | |
557 | uart_write_wakeup(&up->port); | |
558 | ||
559 | if (uart_circ_empty(xmit)) | |
560 | serial_hsu_stop_tx(&up->port); | |
561 | } | |
562 | ||
563 | static inline void check_modem_status(struct uart_hsu_port *up) | |
564 | { | |
565 | int status; | |
566 | ||
567 | status = serial_in(up, UART_MSR); | |
568 | ||
569 | if ((status & UART_MSR_ANY_DELTA) == 0) | |
570 | return; | |
571 | ||
572 | if (status & UART_MSR_TERI) | |
573 | up->port.icount.rng++; | |
574 | if (status & UART_MSR_DDSR) | |
575 | up->port.icount.dsr++; | |
576 | /* We may only get DDCD when HW init and reset */ | |
577 | if (status & UART_MSR_DDCD) | |
578 | uart_handle_dcd_change(&up->port, status & UART_MSR_DCD); | |
06c77e21 | 579 | /* Will start/stop_tx accordingly */ |
d843fc6e FT |
580 | if (status & UART_MSR_DCTS) |
581 | uart_handle_cts_change(&up->port, status & UART_MSR_CTS); | |
582 | ||
583 | wake_up_interruptible(&up->port.state->port.delta_msr_wait); | |
584 | } | |
585 | ||
586 | /* | |
587 | * This handles the interrupt from one port. | |
588 | */ | |
589 | static irqreturn_t port_irq(int irq, void *dev_id) | |
590 | { | |
591 | struct uart_hsu_port *up = dev_id; | |
592 | unsigned int iir, lsr; | |
593 | unsigned long flags; | |
594 | ||
595 | if (unlikely(!up->running)) | |
596 | return IRQ_NONE; | |
597 | ||
06c77e21 | 598 | spin_lock_irqsave(&up->port.lock, flags); |
d843fc6e FT |
599 | if (up->use_dma) { |
600 | lsr = serial_in(up, UART_LSR); | |
601 | if (unlikely(lsr & (UART_LSR_BI | UART_LSR_PE | | |
602 | UART_LSR_FE | UART_LSR_OE))) | |
603 | dev_warn(up->dev, | |
604 | "Got lsr irq while using DMA, lsr = 0x%2x\n", | |
605 | lsr); | |
606 | check_modem_status(up); | |
06c77e21 | 607 | spin_unlock_irqrestore(&up->port.lock, flags); |
d843fc6e FT |
608 | return IRQ_HANDLED; |
609 | } | |
610 | ||
d843fc6e FT |
611 | iir = serial_in(up, UART_IIR); |
612 | if (iir & UART_IIR_NO_INT) { | |
613 | spin_unlock_irqrestore(&up->port.lock, flags); | |
614 | return IRQ_NONE; | |
615 | } | |
616 | ||
617 | lsr = serial_in(up, UART_LSR); | |
d843fc6e FT |
618 | if (lsr & UART_LSR_DR) |
619 | receive_chars(up, &lsr); | |
06c77e21 | 620 | check_modem_status(up); |
d843fc6e FT |
621 | |
622 | /* lsr will be renewed during the receive_chars */ | |
623 | if (lsr & UART_LSR_THRE) | |
624 | transmit_chars(up); | |
625 | ||
626 | spin_unlock_irqrestore(&up->port.lock, flags); | |
627 | return IRQ_HANDLED; | |
628 | } | |
629 | ||
630 | static inline void dma_chan_irq(struct hsu_dma_chan *chan) | |
631 | { | |
632 | struct uart_hsu_port *up = chan->uport; | |
633 | unsigned long flags; | |
634 | u32 int_sts; | |
635 | ||
636 | spin_lock_irqsave(&up->port.lock, flags); | |
637 | ||
638 | if (!up->use_dma || !up->running) | |
639 | goto exit; | |
640 | ||
641 | /* | |
642 | * No matter what situation, need read clear the IRQ status | |
643 | * There is a bug, see Errata 5, HSD 2900918 | |
644 | */ | |
645 | int_sts = chan_readl(chan, HSU_CH_SR); | |
646 | ||
647 | /* Rx channel */ | |
648 | if (chan->dirt == DMA_FROM_DEVICE) | |
649 | hsu_dma_rx(up, int_sts); | |
650 | ||
651 | /* Tx channel */ | |
652 | if (chan->dirt == DMA_TO_DEVICE) { | |
d843fc6e FT |
653 | chan_writel(chan, HSU_CH_CR, 0x0); |
654 | up->dma_tx_on = 0; | |
655 | hsu_dma_tx(up); | |
656 | } | |
657 | ||
658 | exit: | |
659 | spin_unlock_irqrestore(&up->port.lock, flags); | |
660 | return; | |
661 | } | |
662 | ||
663 | static irqreturn_t dma_irq(int irq, void *dev_id) | |
664 | { | |
665 | struct hsu_port *hsu = dev_id; | |
666 | u32 int_sts, i; | |
667 | ||
668 | int_sts = mfd_readl(hsu, HSU_GBL_DMAISR); | |
669 | ||
670 | /* Currently we only have 6 channels may be used */ | |
671 | for (i = 0; i < 6; i++) { | |
672 | if (int_sts & 0x1) | |
673 | dma_chan_irq(&hsu->chans[i]); | |
674 | int_sts >>= 1; | |
675 | } | |
676 | ||
677 | return IRQ_HANDLED; | |
678 | } | |
679 | ||
680 | static unsigned int serial_hsu_tx_empty(struct uart_port *port) | |
681 | { | |
682 | struct uart_hsu_port *up = | |
683 | container_of(port, struct uart_hsu_port, port); | |
684 | unsigned long flags; | |
685 | unsigned int ret; | |
686 | ||
687 | spin_lock_irqsave(&up->port.lock, flags); | |
688 | ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0; | |
689 | spin_unlock_irqrestore(&up->port.lock, flags); | |
690 | ||
691 | return ret; | |
692 | } | |
693 | ||
694 | static unsigned int serial_hsu_get_mctrl(struct uart_port *port) | |
695 | { | |
696 | struct uart_hsu_port *up = | |
697 | container_of(port, struct uart_hsu_port, port); | |
698 | unsigned char status; | |
699 | unsigned int ret; | |
700 | ||
701 | status = serial_in(up, UART_MSR); | |
702 | ||
703 | ret = 0; | |
704 | if (status & UART_MSR_DCD) | |
705 | ret |= TIOCM_CAR; | |
706 | if (status & UART_MSR_RI) | |
707 | ret |= TIOCM_RNG; | |
708 | if (status & UART_MSR_DSR) | |
709 | ret |= TIOCM_DSR; | |
710 | if (status & UART_MSR_CTS) | |
711 | ret |= TIOCM_CTS; | |
712 | return ret; | |
713 | } | |
714 | ||
715 | static void serial_hsu_set_mctrl(struct uart_port *port, unsigned int mctrl) | |
716 | { | |
717 | struct uart_hsu_port *up = | |
718 | container_of(port, struct uart_hsu_port, port); | |
719 | unsigned char mcr = 0; | |
720 | ||
721 | if (mctrl & TIOCM_RTS) | |
722 | mcr |= UART_MCR_RTS; | |
723 | if (mctrl & TIOCM_DTR) | |
724 | mcr |= UART_MCR_DTR; | |
725 | if (mctrl & TIOCM_OUT1) | |
726 | mcr |= UART_MCR_OUT1; | |
727 | if (mctrl & TIOCM_OUT2) | |
728 | mcr |= UART_MCR_OUT2; | |
729 | if (mctrl & TIOCM_LOOP) | |
730 | mcr |= UART_MCR_LOOP; | |
731 | ||
732 | mcr |= up->mcr; | |
733 | ||
734 | serial_out(up, UART_MCR, mcr); | |
735 | } | |
736 | ||
737 | static void serial_hsu_break_ctl(struct uart_port *port, int break_state) | |
738 | { | |
739 | struct uart_hsu_port *up = | |
740 | container_of(port, struct uart_hsu_port, port); | |
741 | unsigned long flags; | |
742 | ||
743 | spin_lock_irqsave(&up->port.lock, flags); | |
744 | if (break_state == -1) | |
745 | up->lcr |= UART_LCR_SBC; | |
746 | else | |
747 | up->lcr &= ~UART_LCR_SBC; | |
748 | serial_out(up, UART_LCR, up->lcr); | |
749 | spin_unlock_irqrestore(&up->port.lock, flags); | |
750 | } | |
751 | ||
752 | /* | |
753 | * What special to do: | |
754 | * 1. chose the 64B fifo mode | |
085a4f75 FT |
755 | * 2. start dma or pio depends on configuration |
756 | * 3. we only allocate dma memory when needed | |
d843fc6e FT |
757 | */ |
758 | static int serial_hsu_startup(struct uart_port *port) | |
759 | { | |
760 | struct uart_hsu_port *up = | |
761 | container_of(port, struct uart_hsu_port, port); | |
762 | unsigned long flags; | |
763 | ||
88e5173f KCA |
764 | pm_runtime_get_sync(up->dev); |
765 | ||
d843fc6e FT |
766 | /* |
767 | * Clear the FIFO buffers and disable them. | |
768 | * (they will be reenabled in set_termios()) | |
769 | */ | |
770 | serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); | |
771 | serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | | |
772 | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); | |
773 | serial_out(up, UART_FCR, 0); | |
774 | ||
775 | /* Clear the interrupt registers. */ | |
776 | (void) serial_in(up, UART_LSR); | |
777 | (void) serial_in(up, UART_RX); | |
778 | (void) serial_in(up, UART_IIR); | |
779 | (void) serial_in(up, UART_MSR); | |
780 | ||
781 | /* Now, initialize the UART, default is 8n1 */ | |
782 | serial_out(up, UART_LCR, UART_LCR_WLEN8); | |
783 | ||
784 | spin_lock_irqsave(&up->port.lock, flags); | |
785 | ||
786 | up->port.mctrl |= TIOCM_OUT2; | |
787 | serial_hsu_set_mctrl(&up->port, up->port.mctrl); | |
788 | ||
789 | /* | |
790 | * Finally, enable interrupts. Note: Modem status interrupts | |
791 | * are set via set_termios(), which will be occurring imminently | |
792 | * anyway, so we don't enable them here. | |
793 | */ | |
794 | if (!up->use_dma) | |
795 | up->ier = UART_IER_RLSI | UART_IER_RDI | UART_IER_RTOIE; | |
796 | else | |
797 | up->ier = 0; | |
798 | serial_out(up, UART_IER, up->ier); | |
799 | ||
800 | spin_unlock_irqrestore(&up->port.lock, flags); | |
801 | ||
802 | /* DMA init */ | |
d843fc6e FT |
803 | if (up->use_dma) { |
804 | struct hsu_dma_buffer *dbuf; | |
805 | struct circ_buf *xmit = &port->state->xmit; | |
806 | ||
807 | up->dma_tx_on = 0; | |
808 | ||
809 | /* First allocate the RX buffer */ | |
810 | dbuf = &up->rxbuf; | |
811 | dbuf->buf = kzalloc(HSU_DMA_BUF_SIZE, GFP_KERNEL); | |
812 | if (!dbuf->buf) { | |
813 | up->use_dma = 0; | |
814 | goto exit; | |
815 | } | |
816 | dbuf->dma_addr = dma_map_single(port->dev, | |
817 | dbuf->buf, | |
818 | HSU_DMA_BUF_SIZE, | |
819 | DMA_FROM_DEVICE); | |
820 | dbuf->dma_size = HSU_DMA_BUF_SIZE; | |
821 | ||
822 | /* Start the RX channel right now */ | |
823 | hsu_dma_start_rx_chan(up->rxc, dbuf); | |
824 | ||
825 | /* Next init the TX DMA */ | |
826 | dbuf = &up->txbuf; | |
827 | dbuf->buf = xmit->buf; | |
828 | dbuf->dma_addr = dma_map_single(port->dev, | |
829 | dbuf->buf, | |
830 | UART_XMIT_SIZE, | |
831 | DMA_TO_DEVICE); | |
832 | dbuf->dma_size = UART_XMIT_SIZE; | |
833 | ||
834 | /* This should not be changed all around */ | |
835 | chan_writel(up->txc, HSU_CH_BSR, 32); | |
836 | chan_writel(up->txc, HSU_CH_MOTSR, 4); | |
837 | dbuf->ofs = 0; | |
838 | } | |
839 | ||
840 | exit: | |
841 | /* And clear the interrupt registers again for luck. */ | |
842 | (void) serial_in(up, UART_LSR); | |
843 | (void) serial_in(up, UART_RX); | |
844 | (void) serial_in(up, UART_IIR); | |
845 | (void) serial_in(up, UART_MSR); | |
846 | ||
847 | up->running = 1; | |
848 | return 0; | |
849 | } | |
850 | ||
851 | static void serial_hsu_shutdown(struct uart_port *port) | |
852 | { | |
853 | struct uart_hsu_port *up = | |
854 | container_of(port, struct uart_hsu_port, port); | |
855 | unsigned long flags; | |
856 | ||
857 | /* Disable interrupts from this port */ | |
858 | up->ier = 0; | |
859 | serial_out(up, UART_IER, 0); | |
860 | up->running = 0; | |
861 | ||
862 | spin_lock_irqsave(&up->port.lock, flags); | |
863 | up->port.mctrl &= ~TIOCM_OUT2; | |
864 | serial_hsu_set_mctrl(&up->port, up->port.mctrl); | |
865 | spin_unlock_irqrestore(&up->port.lock, flags); | |
866 | ||
867 | /* Disable break condition and FIFOs */ | |
868 | serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC); | |
869 | serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | | |
870 | UART_FCR_CLEAR_RCVR | | |
871 | UART_FCR_CLEAR_XMIT); | |
872 | serial_out(up, UART_FCR, 0); | |
88e5173f KCA |
873 | |
874 | pm_runtime_put(up->dev); | |
d843fc6e FT |
875 | } |
876 | ||
877 | static void | |
878 | serial_hsu_set_termios(struct uart_port *port, struct ktermios *termios, | |
879 | struct ktermios *old) | |
880 | { | |
881 | struct uart_hsu_port *up = | |
882 | container_of(port, struct uart_hsu_port, port); | |
d843fc6e FT |
883 | unsigned char cval, fcr = 0; |
884 | unsigned long flags; | |
885 | unsigned int baud, quot; | |
a5880a9e | 886 | u32 ps, mul; |
d843fc6e FT |
887 | |
888 | switch (termios->c_cflag & CSIZE) { | |
889 | case CS5: | |
890 | cval = UART_LCR_WLEN5; | |
891 | break; | |
892 | case CS6: | |
893 | cval = UART_LCR_WLEN6; | |
894 | break; | |
895 | case CS7: | |
896 | cval = UART_LCR_WLEN7; | |
897 | break; | |
898 | default: | |
899 | case CS8: | |
900 | cval = UART_LCR_WLEN8; | |
901 | break; | |
902 | } | |
903 | ||
904 | /* CMSPAR isn't supported by this driver */ | |
604fdb75 | 905 | termios->c_cflag &= ~CMSPAR; |
d843fc6e FT |
906 | |
907 | if (termios->c_cflag & CSTOPB) | |
908 | cval |= UART_LCR_STOP; | |
909 | if (termios->c_cflag & PARENB) | |
910 | cval |= UART_LCR_PARITY; | |
911 | if (!(termios->c_cflag & PARODD)) | |
912 | cval |= UART_LCR_EPAR; | |
913 | ||
914 | /* | |
e5586ecc FT |
915 | * The base clk is 50Mhz, and the baud rate come from: |
916 | * baud = 50M * MUL / (DIV * PS * DLAB) | |
917 | * | |
d843fc6e | 918 | * For those basic low baud rate we can get the direct |
e5586ecc FT |
919 | * scalar from 2746800, like 115200 = 2746800/24. For those |
920 | * higher baud rate, we handle them case by case, mainly by | |
921 | * adjusting the MUL/PS registers, and DIV register is kept | |
922 | * as default value 0x3d09 to make things simple | |
d843fc6e FT |
923 | */ |
924 | baud = uart_get_baud_rate(port, termios, old, 0, 4000000); | |
d843fc6e | 925 | |
e5586ecc | 926 | quot = 1; |
a5880a9e FT |
927 | ps = 0x10; |
928 | mul = 0x3600; | |
d843fc6e FT |
929 | switch (baud) { |
930 | case 3500000: | |
931 | mul = 0x3345; | |
932 | ps = 0xC; | |
e5586ecc | 933 | break; |
e5586ecc | 934 | case 1843200: |
d843fc6e | 935 | mul = 0x2400; |
d843fc6e | 936 | break; |
a5880a9e FT |
937 | case 3000000: |
938 | case 2500000: | |
939 | case 2000000: | |
d843fc6e | 940 | case 1500000: |
e5586ecc | 941 | case 1000000: |
e5586ecc | 942 | case 500000: |
a5880a9e FT |
943 | /* mul/ps/quot = 0x9C4/0x10/0x1 will make a 500000 bps */ |
944 | mul = baud / 500000 * 0x9C4; | |
d843fc6e FT |
945 | break; |
946 | default: | |
e5586ecc FT |
947 | /* Use uart_get_divisor to get quot for other baud rates */ |
948 | quot = 0; | |
d843fc6e FT |
949 | } |
950 | ||
e5586ecc FT |
951 | if (!quot) |
952 | quot = uart_get_divisor(port, baud); | |
953 | ||
d843fc6e FT |
954 | if ((up->port.uartclk / quot) < (2400 * 16)) |
955 | fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_1B; | |
956 | else if ((up->port.uartclk / quot) < (230400 * 16)) | |
957 | fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_16B; | |
958 | else | |
959 | fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_32B; | |
960 | ||
961 | fcr |= UART_FCR_HSU_64B_FIFO; | |
d843fc6e FT |
962 | |
963 | /* | |
964 | * Ok, we're now changing the port state. Do it with | |
965 | * interrupts disabled. | |
966 | */ | |
967 | spin_lock_irqsave(&up->port.lock, flags); | |
968 | ||
969 | /* Update the per-port timeout */ | |
970 | uart_update_timeout(port, termios->c_cflag, baud); | |
971 | ||
972 | up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; | |
973 | if (termios->c_iflag & INPCK) | |
974 | up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE; | |
975 | if (termios->c_iflag & (BRKINT | PARMRK)) | |
976 | up->port.read_status_mask |= UART_LSR_BI; | |
977 | ||
978 | /* Characters to ignore */ | |
979 | up->port.ignore_status_mask = 0; | |
980 | if (termios->c_iflag & IGNPAR) | |
981 | up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; | |
982 | if (termios->c_iflag & IGNBRK) { | |
983 | up->port.ignore_status_mask |= UART_LSR_BI; | |
984 | /* | |
985 | * If we're ignoring parity and break indicators, | |
986 | * ignore overruns too (for real raw support). | |
987 | */ | |
988 | if (termios->c_iflag & IGNPAR) | |
989 | up->port.ignore_status_mask |= UART_LSR_OE; | |
990 | } | |
991 | ||
992 | /* Ignore all characters if CREAD is not set */ | |
993 | if ((termios->c_cflag & CREAD) == 0) | |
994 | up->port.ignore_status_mask |= UART_LSR_DR; | |
995 | ||
996 | /* | |
997 | * CTS flow control flag and modem status interrupts, disable | |
998 | * MSI by default | |
999 | */ | |
1000 | up->ier &= ~UART_IER_MSI; | |
1001 | if (UART_ENABLE_MS(&up->port, termios->c_cflag)) | |
1002 | up->ier |= UART_IER_MSI; | |
1003 | ||
1004 | serial_out(up, UART_IER, up->ier); | |
1005 | ||
1006 | if (termios->c_cflag & CRTSCTS) | |
1007 | up->mcr |= UART_MCR_AFE | UART_MCR_RTS; | |
1008 | else | |
1009 | up->mcr &= ~UART_MCR_AFE; | |
1010 | ||
1011 | serial_out(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */ | |
1012 | serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */ | |
1013 | serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */ | |
1014 | serial_out(up, UART_LCR, cval); /* reset DLAB */ | |
1015 | serial_out(up, UART_MUL, mul); /* set MUL */ | |
1016 | serial_out(up, UART_PS, ps); /* set PS */ | |
1017 | up->lcr = cval; /* Save LCR */ | |
1018 | serial_hsu_set_mctrl(&up->port, up->port.mctrl); | |
1019 | serial_out(up, UART_FCR, fcr); | |
1020 | spin_unlock_irqrestore(&up->port.lock, flags); | |
1021 | } | |
1022 | ||
1023 | static void | |
1024 | serial_hsu_pm(struct uart_port *port, unsigned int state, | |
1025 | unsigned int oldstate) | |
1026 | { | |
1027 | } | |
1028 | ||
1029 | static void serial_hsu_release_port(struct uart_port *port) | |
1030 | { | |
1031 | } | |
1032 | ||
1033 | static int serial_hsu_request_port(struct uart_port *port) | |
1034 | { | |
1035 | return 0; | |
1036 | } | |
1037 | ||
1038 | static void serial_hsu_config_port(struct uart_port *port, int flags) | |
1039 | { | |
d843fc6e FT |
1040 | struct uart_hsu_port *up = |
1041 | container_of(port, struct uart_hsu_port, port); | |
1042 | up->port.type = PORT_MFD; | |
d843fc6e FT |
1043 | } |
1044 | ||
1045 | static int | |
1046 | serial_hsu_verify_port(struct uart_port *port, struct serial_struct *ser) | |
1047 | { | |
1048 | /* We don't want the core code to modify any port params */ | |
1049 | return -EINVAL; | |
1050 | } | |
1051 | ||
1052 | static const char * | |
1053 | serial_hsu_type(struct uart_port *port) | |
1054 | { | |
1055 | struct uart_hsu_port *up = | |
1056 | container_of(port, struct uart_hsu_port, port); | |
1057 | return up->name; | |
1058 | } | |
1059 | ||
1060 | /* Mainly for uart console use */ | |
1061 | static struct uart_hsu_port *serial_hsu_ports[3]; | |
1062 | static struct uart_driver serial_hsu_reg; | |
1063 | ||
1064 | #ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE | |
1065 | ||
1066 | #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) | |
1067 | ||
1068 | /* Wait for transmitter & holding register to empty */ | |
1069 | static inline void wait_for_xmitr(struct uart_hsu_port *up) | |
1070 | { | |
1071 | unsigned int status, tmout = 1000; | |
1072 | ||
1073 | /* Wait up to 1ms for the character to be sent. */ | |
1074 | do { | |
1075 | status = serial_in(up, UART_LSR); | |
1076 | ||
1077 | if (status & UART_LSR_BI) | |
1078 | up->lsr_break_flag = UART_LSR_BI; | |
1079 | ||
1080 | if (--tmout == 0) | |
1081 | break; | |
1082 | udelay(1); | |
1083 | } while (!(status & BOTH_EMPTY)); | |
1084 | ||
1085 | /* Wait up to 1s for flow control if necessary */ | |
1086 | if (up->port.flags & UPF_CONS_FLOW) { | |
1087 | tmout = 1000000; | |
1088 | while (--tmout && | |
1089 | ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0)) | |
1090 | udelay(1); | |
1091 | } | |
1092 | } | |
1093 | ||
1094 | static void serial_hsu_console_putchar(struct uart_port *port, int ch) | |
1095 | { | |
1096 | struct uart_hsu_port *up = | |
1097 | container_of(port, struct uart_hsu_port, port); | |
1098 | ||
1099 | wait_for_xmitr(up); | |
1100 | serial_out(up, UART_TX, ch); | |
1101 | } | |
1102 | ||
1103 | /* | |
1104 | * Print a string to the serial port trying not to disturb | |
1105 | * any possible real use of the port... | |
1106 | * | |
1107 | * The console_lock must be held when we get here. | |
1108 | */ | |
1109 | static void | |
1110 | serial_hsu_console_write(struct console *co, const char *s, unsigned int count) | |
1111 | { | |
1112 | struct uart_hsu_port *up = serial_hsu_ports[co->index]; | |
1113 | unsigned long flags; | |
1114 | unsigned int ier; | |
1115 | int locked = 1; | |
1116 | ||
50827fbd FT |
1117 | touch_nmi_watchdog(); |
1118 | ||
d843fc6e FT |
1119 | local_irq_save(flags); |
1120 | if (up->port.sysrq) | |
1121 | locked = 0; | |
1122 | else if (oops_in_progress) { | |
1123 | locked = spin_trylock(&up->port.lock); | |
1124 | } else | |
1125 | spin_lock(&up->port.lock); | |
1126 | ||
1127 | /* First save the IER then disable the interrupts */ | |
1128 | ier = serial_in(up, UART_IER); | |
1129 | serial_out(up, UART_IER, 0); | |
1130 | ||
1131 | uart_console_write(&up->port, s, count, serial_hsu_console_putchar); | |
1132 | ||
1133 | /* | |
1134 | * Finally, wait for transmitter to become empty | |
1135 | * and restore the IER | |
1136 | */ | |
1137 | wait_for_xmitr(up); | |
1138 | serial_out(up, UART_IER, ier); | |
1139 | ||
1140 | if (locked) | |
1141 | spin_unlock(&up->port.lock); | |
1142 | local_irq_restore(flags); | |
1143 | } | |
1144 | ||
1145 | static struct console serial_hsu_console; | |
1146 | ||
1147 | static int __init | |
1148 | serial_hsu_console_setup(struct console *co, char *options) | |
1149 | { | |
1150 | struct uart_hsu_port *up; | |
1151 | int baud = 115200; | |
1152 | int bits = 8; | |
1153 | int parity = 'n'; | |
1154 | int flow = 'n'; | |
d843fc6e FT |
1155 | |
1156 | if (co->index == -1 || co->index >= serial_hsu_reg.nr) | |
1157 | co->index = 0; | |
1158 | up = serial_hsu_ports[co->index]; | |
1159 | if (!up) | |
1160 | return -ENODEV; | |
1161 | ||
1162 | if (options) | |
1163 | uart_parse_options(options, &baud, &parity, &bits, &flow); | |
1164 | ||
b82e324b | 1165 | return uart_set_options(&up->port, co, baud, parity, bits, flow); |
d843fc6e FT |
1166 | } |
1167 | ||
1168 | static struct console serial_hsu_console = { | |
1169 | .name = "ttyMFD", | |
1170 | .write = serial_hsu_console_write, | |
1171 | .device = uart_console_device, | |
1172 | .setup = serial_hsu_console_setup, | |
1173 | .flags = CON_PRINTBUFFER, | |
b82e324b | 1174 | .index = -1, |
d843fc6e FT |
1175 | .data = &serial_hsu_reg, |
1176 | }; | |
b82e324b MW |
1177 | |
1178 | #define SERIAL_HSU_CONSOLE (&serial_hsu_console) | |
1179 | #else | |
1180 | #define SERIAL_HSU_CONSOLE NULL | |
d843fc6e FT |
1181 | #endif |
1182 | ||
1183 | struct uart_ops serial_hsu_pops = { | |
1184 | .tx_empty = serial_hsu_tx_empty, | |
1185 | .set_mctrl = serial_hsu_set_mctrl, | |
1186 | .get_mctrl = serial_hsu_get_mctrl, | |
1187 | .stop_tx = serial_hsu_stop_tx, | |
1188 | .start_tx = serial_hsu_start_tx, | |
1189 | .stop_rx = serial_hsu_stop_rx, | |
1190 | .enable_ms = serial_hsu_enable_ms, | |
1191 | .break_ctl = serial_hsu_break_ctl, | |
1192 | .startup = serial_hsu_startup, | |
1193 | .shutdown = serial_hsu_shutdown, | |
1194 | .set_termios = serial_hsu_set_termios, | |
1195 | .pm = serial_hsu_pm, | |
1196 | .type = serial_hsu_type, | |
1197 | .release_port = serial_hsu_release_port, | |
1198 | .request_port = serial_hsu_request_port, | |
1199 | .config_port = serial_hsu_config_port, | |
1200 | .verify_port = serial_hsu_verify_port, | |
1201 | }; | |
1202 | ||
1203 | static struct uart_driver serial_hsu_reg = { | |
1204 | .owner = THIS_MODULE, | |
1205 | .driver_name = "MFD serial", | |
1206 | .dev_name = "ttyMFD", | |
1207 | .major = TTY_MAJOR, | |
1208 | .minor = 128, | |
1209 | .nr = 3, | |
b82e324b | 1210 | .cons = SERIAL_HSU_CONSOLE, |
d843fc6e FT |
1211 | }; |
1212 | ||
1213 | #ifdef CONFIG_PM | |
1214 | static int serial_hsu_suspend(struct pci_dev *pdev, pm_message_t state) | |
1215 | { | |
3c4108c8 | 1216 | void *priv = pci_get_drvdata(pdev); |
d843fc6e FT |
1217 | struct uart_hsu_port *up; |
1218 | ||
3c4108c8 FT |
1219 | /* Make sure this is not the internal dma controller */ |
1220 | if (priv && (pdev->device != 0x081E)) { | |
1221 | up = priv; | |
1222 | uart_suspend_port(&serial_hsu_reg, &up->port); | |
1223 | } | |
d843fc6e | 1224 | |
3c4108c8 FT |
1225 | pci_save_state(pdev); |
1226 | pci_set_power_state(pdev, pci_choose_state(pdev, state)); | |
d843fc6e FT |
1227 | return 0; |
1228 | } | |
1229 | ||
1230 | static int serial_hsu_resume(struct pci_dev *pdev) | |
1231 | { | |
3c4108c8 | 1232 | void *priv = pci_get_drvdata(pdev); |
d843fc6e | 1233 | struct uart_hsu_port *up; |
3c4108c8 | 1234 | int ret; |
d843fc6e | 1235 | |
3c4108c8 FT |
1236 | pci_set_power_state(pdev, PCI_D0); |
1237 | pci_restore_state(pdev); | |
1238 | ||
1239 | ret = pci_enable_device(pdev); | |
1240 | if (ret) | |
1241 | dev_warn(&pdev->dev, | |
1242 | "HSU: can't re-enable device, try to continue\n"); | |
1243 | ||
1244 | if (priv && (pdev->device != 0x081E)) { | |
1245 | up = priv; | |
1246 | uart_resume_port(&serial_hsu_reg, &up->port); | |
1247 | } | |
d843fc6e FT |
1248 | return 0; |
1249 | } | |
1250 | #else | |
1251 | #define serial_hsu_suspend NULL | |
1252 | #define serial_hsu_resume NULL | |
1253 | #endif | |
1254 | ||
88e5173f KCA |
1255 | #ifdef CONFIG_PM_RUNTIME |
1256 | static int serial_hsu_runtime_idle(struct device *dev) | |
1257 | { | |
1258 | int err; | |
1259 | ||
1260 | err = pm_schedule_suspend(dev, 500); | |
1261 | if (err) | |
1262 | return -EBUSY; | |
1263 | ||
1264 | return 0; | |
1265 | } | |
1266 | ||
1267 | static int serial_hsu_runtime_suspend(struct device *dev) | |
1268 | { | |
1269 | return 0; | |
1270 | } | |
1271 | ||
1272 | static int serial_hsu_runtime_resume(struct device *dev) | |
1273 | { | |
1274 | return 0; | |
1275 | } | |
1276 | #else | |
1277 | #define serial_hsu_runtime_idle NULL | |
1278 | #define serial_hsu_runtime_suspend NULL | |
1279 | #define serial_hsu_runtime_resume NULL | |
1280 | #endif | |
1281 | ||
1282 | static const struct dev_pm_ops serial_hsu_pm_ops = { | |
1283 | .runtime_suspend = serial_hsu_runtime_suspend, | |
1284 | .runtime_resume = serial_hsu_runtime_resume, | |
1285 | .runtime_idle = serial_hsu_runtime_idle, | |
1286 | }; | |
1287 | ||
d843fc6e FT |
1288 | /* temp global pointer before we settle down on using one or four PCI dev */ |
1289 | static struct hsu_port *phsu; | |
1290 | ||
1291 | static int serial_hsu_probe(struct pci_dev *pdev, | |
1292 | const struct pci_device_id *ent) | |
1293 | { | |
1294 | struct uart_hsu_port *uport; | |
1295 | int index, ret; | |
1296 | ||
1297 | printk(KERN_INFO "HSU: found PCI Serial controller(ID: %04x:%04x)\n", | |
1298 | pdev->vendor, pdev->device); | |
1299 | ||
1300 | switch (pdev->device) { | |
1301 | case 0x081B: | |
1302 | index = 0; | |
1303 | break; | |
1304 | case 0x081C: | |
1305 | index = 1; | |
1306 | break; | |
1307 | case 0x081D: | |
1308 | index = 2; | |
1309 | break; | |
1310 | case 0x081E: | |
1311 | /* internal DMA controller */ | |
1312 | index = 3; | |
1313 | break; | |
1314 | default: | |
1315 | dev_err(&pdev->dev, "HSU: out of index!"); | |
1316 | return -ENODEV; | |
1317 | } | |
1318 | ||
1319 | ret = pci_enable_device(pdev); | |
1320 | if (ret) | |
1321 | return ret; | |
1322 | ||
1323 | if (index == 3) { | |
1324 | /* DMA controller */ | |
1325 | ret = request_irq(pdev->irq, dma_irq, 0, "hsu_dma", phsu); | |
1326 | if (ret) { | |
1327 | dev_err(&pdev->dev, "can not get IRQ\n"); | |
1328 | goto err_disable; | |
1329 | } | |
1330 | pci_set_drvdata(pdev, phsu); | |
1331 | } else { | |
1332 | /* UART port 0~2 */ | |
1333 | uport = &phsu->port[index]; | |
1334 | uport->port.irq = pdev->irq; | |
1335 | uport->port.dev = &pdev->dev; | |
1336 | uport->dev = &pdev->dev; | |
1337 | ||
1338 | ret = request_irq(pdev->irq, port_irq, 0, uport->name, uport); | |
1339 | if (ret) { | |
1340 | dev_err(&pdev->dev, "can not get IRQ\n"); | |
1341 | goto err_disable; | |
1342 | } | |
1343 | uart_add_one_port(&serial_hsu_reg, &uport->port); | |
1344 | ||
d843fc6e FT |
1345 | pci_set_drvdata(pdev, uport); |
1346 | } | |
1347 | ||
88e5173f KCA |
1348 | pm_runtime_put_noidle(&pdev->dev); |
1349 | pm_runtime_allow(&pdev->dev); | |
1350 | ||
d843fc6e FT |
1351 | return 0; |
1352 | ||
1353 | err_disable: | |
1354 | pci_disable_device(pdev); | |
1355 | return ret; | |
1356 | } | |
1357 | ||
1358 | static void hsu_global_init(void) | |
1359 | { | |
1360 | struct hsu_port *hsu; | |
1361 | struct uart_hsu_port *uport; | |
1362 | struct hsu_dma_chan *dchan; | |
1363 | int i, ret; | |
1364 | ||
1365 | hsu = kzalloc(sizeof(struct hsu_port), GFP_KERNEL); | |
1366 | if (!hsu) | |
1367 | return; | |
1368 | ||
1369 | /* Get basic io resource and map it */ | |
1370 | hsu->paddr = 0xffa28000; | |
1371 | hsu->iolen = 0x1000; | |
1372 | ||
1373 | if (!(request_mem_region(hsu->paddr, hsu->iolen, "HSU global"))) | |
1374 | pr_warning("HSU: error in request mem region\n"); | |
1375 | ||
1376 | hsu->reg = ioremap_nocache((unsigned long)hsu->paddr, hsu->iolen); | |
1377 | if (!hsu->reg) { | |
1378 | pr_err("HSU: error in ioremap\n"); | |
1379 | ret = -ENOMEM; | |
1380 | goto err_free_region; | |
1381 | } | |
1382 | ||
1383 | /* Initialise the 3 UART ports */ | |
1384 | uport = hsu->port; | |
1385 | for (i = 0; i < 3; i++) { | |
1386 | uport->port.type = PORT_MFD; | |
1387 | uport->port.iotype = UPIO_MEM; | |
1388 | uport->port.mapbase = (resource_size_t)hsu->paddr | |
1389 | + HSU_PORT_REG_OFFSET | |
1390 | + i * HSU_PORT_REG_LENGTH; | |
1391 | uport->port.membase = hsu->reg + HSU_PORT_REG_OFFSET | |
1392 | + i * HSU_PORT_REG_LENGTH; | |
1393 | ||
1394 | sprintf(uport->name, "hsu_port%d", i); | |
1395 | uport->port.fifosize = 64; | |
1396 | uport->port.ops = &serial_hsu_pops; | |
1397 | uport->port.line = i; | |
1398 | uport->port.flags = UPF_IOREMAP; | |
06c77e21 | 1399 | /* set the scalable maxim support rate to 2746800 bps */ |
d843fc6e FT |
1400 | uport->port.uartclk = 115200 * 24 * 16; |
1401 | ||
1402 | uport->running = 0; | |
1403 | uport->txc = &hsu->chans[i * 2]; | |
1404 | uport->rxc = &hsu->chans[i * 2 + 1]; | |
1405 | ||
1406 | serial_hsu_ports[i] = uport; | |
1407 | uport->index = i; | |
f023eab3 FT |
1408 | |
1409 | if (hsu_dma_enable & (1<<i)) | |
1410 | uport->use_dma = 1; | |
1411 | else | |
1412 | uport->use_dma = 0; | |
1413 | ||
d843fc6e FT |
1414 | uport++; |
1415 | } | |
1416 | ||
1417 | /* Initialise 6 dma channels */ | |
1418 | dchan = hsu->chans; | |
1419 | for (i = 0; i < 6; i++) { | |
1420 | dchan->id = i; | |
1421 | dchan->dirt = (i & 0x1) ? DMA_FROM_DEVICE : DMA_TO_DEVICE; | |
1422 | dchan->uport = &hsu->port[i/2]; | |
1423 | dchan->reg = hsu->reg + HSU_DMA_CHANS_REG_OFFSET + | |
1424 | i * HSU_DMA_CHANS_REG_LENGTH; | |
669b7a09 | 1425 | |
d843fc6e FT |
1426 | dchan++; |
1427 | } | |
1428 | ||
1429 | phsu = hsu; | |
d843fc6e FT |
1430 | hsu_debugfs_init(hsu); |
1431 | return; | |
1432 | ||
1433 | err_free_region: | |
1434 | release_mem_region(hsu->paddr, hsu->iolen); | |
1435 | kfree(hsu); | |
1436 | return; | |
1437 | } | |
1438 | ||
1439 | static void serial_hsu_remove(struct pci_dev *pdev) | |
1440 | { | |
e3671ac4 FT |
1441 | void *priv = pci_get_drvdata(pdev); |
1442 | struct uart_hsu_port *up; | |
d843fc6e | 1443 | |
e3671ac4 | 1444 | if (!priv) |
d843fc6e FT |
1445 | return; |
1446 | ||
88e5173f KCA |
1447 | pm_runtime_forbid(&pdev->dev); |
1448 | pm_runtime_get_noresume(&pdev->dev); | |
1449 | ||
e3671ac4 FT |
1450 | /* For port 0/1/2, priv is the address of uart_hsu_port */ |
1451 | if (pdev->device != 0x081E) { | |
1452 | up = priv; | |
1453 | uart_remove_one_port(&serial_hsu_reg, &up->port); | |
1454 | } | |
d843fc6e FT |
1455 | |
1456 | pci_set_drvdata(pdev, NULL); | |
e3671ac4 | 1457 | free_irq(pdev->irq, priv); |
d843fc6e FT |
1458 | pci_disable_device(pdev); |
1459 | } | |
1460 | ||
1461 | /* First 3 are UART ports, and the 4th is the DMA */ | |
153d3d9b | 1462 | static const struct pci_device_id pci_ids[] __devinitconst = { |
d843fc6e FT |
1463 | { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081B) }, |
1464 | { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081C) }, | |
1465 | { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081D) }, | |
1466 | { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081E) }, | |
1467 | {}, | |
1468 | }; | |
1469 | ||
1470 | static struct pci_driver hsu_pci_driver = { | |
1471 | .name = "HSU serial", | |
1472 | .id_table = pci_ids, | |
1473 | .probe = serial_hsu_probe, | |
2d47b716 | 1474 | .remove = serial_hsu_remove, |
d843fc6e FT |
1475 | .suspend = serial_hsu_suspend, |
1476 | .resume = serial_hsu_resume, | |
88e5173f KCA |
1477 | .driver = { |
1478 | .pm = &serial_hsu_pm_ops, | |
1479 | }, | |
d843fc6e FT |
1480 | }; |
1481 | ||
1482 | static int __init hsu_pci_init(void) | |
1483 | { | |
1484 | int ret; | |
1485 | ||
1486 | hsu_global_init(); | |
1487 | ||
1488 | ret = uart_register_driver(&serial_hsu_reg); | |
1489 | if (ret) | |
1490 | return ret; | |
1491 | ||
1492 | return pci_register_driver(&hsu_pci_driver); | |
1493 | } | |
1494 | ||
1495 | static void __exit hsu_pci_exit(void) | |
1496 | { | |
1497 | pci_unregister_driver(&hsu_pci_driver); | |
1498 | uart_unregister_driver(&serial_hsu_reg); | |
1499 | ||
1500 | hsu_debugfs_remove(phsu); | |
1501 | ||
1502 | kfree(phsu); | |
1503 | } | |
1504 | ||
1505 | module_init(hsu_pci_init); | |
1506 | module_exit(hsu_pci_exit); | |
1507 | ||
1508 | MODULE_LICENSE("GPL v2"); | |
1509 | MODULE_ALIAS("platform:medfield-hsu"); |