Commit | Line | Data |
---|---|---|
d7584ed2 TT |
1 | /* |
2 | * Freescale QUICC Engine UART device driver | |
3 | * | |
4 | * Author: Timur Tabi <timur@freescale.com> | |
5 | * | |
6 | * Copyright 2007 Freescale Semiconductor, Inc. This file is licensed under | |
7 | * the terms of the GNU General Public License version 2. This program | |
8 | * is licensed "as is" without any warranty of any kind, whether express | |
9 | * or implied. | |
10 | * | |
11 | * This driver adds support for UART devices via Freescale's QUICC Engine | |
12 | * found on some Freescale SOCs. | |
13 | * | |
14 | * If Soft-UART support is needed but not already present, then this driver | |
15 | * will request and upload the "Soft-UART" microcode upon probe. The | |
16 | * filename of the microcode should be fsl_qe_ucode_uart_X_YZ.bin, where "X" | |
17 | * is the name of the SOC (e.g. 8323), and YZ is the revision of the SOC, | |
18 | * (e.g. "11" for 1.1). | |
19 | */ | |
20 | ||
21 | #include <linux/module.h> | |
22 | #include <linux/serial.h> | |
23 | #include <linux/serial_core.h> | |
ee160a38 JS |
24 | #include <linux/slab.h> |
25 | #include <linux/tty.h> | |
26 | #include <linux/tty_flip.h> | |
d7584ed2 TT |
27 | #include <linux/io.h> |
28 | #include <linux/of_platform.h> | |
29 | #include <linux/dma-mapping.h> | |
30 | ||
31 | #include <linux/fs_uart_pd.h> | |
32 | #include <asm/ucc_slow.h> | |
33 | ||
34 | #include <linux/firmware.h> | |
35 | #include <asm/reg.h> | |
36 | ||
37 | /* | |
38 | * The GUMR flag for Soft UART. This would normally be defined in qe.h, | |
39 | * but Soft-UART is a hack and we want to keep everything related to it in | |
40 | * this file. | |
41 | */ | |
42 | #define UCC_SLOW_GUMR_H_SUART 0x00004000 /* Soft-UART */ | |
43 | ||
44 | /* | |
45 | * soft_uart is 1 if we need to use Soft-UART mode | |
46 | */ | |
47 | static int soft_uart; | |
48 | /* | |
49 | * firmware_loaded is 1 if the firmware has been loaded, 0 otherwise. | |
50 | */ | |
51 | static int firmware_loaded; | |
52 | ||
53 | /* Enable this macro to configure all serial ports in internal loopback | |
54 | mode */ | |
55 | /* #define LOOPBACK */ | |
56 | ||
57 | /* The major and minor device numbers are defined in | |
58 | * http://www.lanana.org/docs/device-list/devices-2.6+.txt. For the QE | |
59 | * UART, we have major number 204 and minor numbers 46 - 49, which are the | |
60 | * same as for the CPM2. This decision was made because no Freescale part | |
61 | * has both a CPM and a QE. | |
62 | */ | |
63 | #define SERIAL_QE_MAJOR 204 | |
64 | #define SERIAL_QE_MINOR 46 | |
65 | ||
66 | /* Since we only have minor numbers 46 - 49, there is a hard limit of 4 ports */ | |
67 | #define UCC_MAX_UART 4 | |
68 | ||
69 | /* The number of buffer descriptors for receiving characters. */ | |
70 | #define RX_NUM_FIFO 4 | |
71 | ||
72 | /* The number of buffer descriptors for transmitting characters. */ | |
73 | #define TX_NUM_FIFO 4 | |
74 | ||
75 | /* The maximum size of the character buffer for a single RX BD. */ | |
76 | #define RX_BUF_SIZE 32 | |
77 | ||
78 | /* The maximum size of the character buffer for a single TX BD. */ | |
79 | #define TX_BUF_SIZE 32 | |
80 | ||
81 | /* | |
82 | * The number of jiffies to wait after receiving a close command before the | |
83 | * device is actually closed. This allows the last few characters to be | |
84 | * sent over the wire. | |
85 | */ | |
86 | #define UCC_WAIT_CLOSING 100 | |
87 | ||
88 | struct ucc_uart_pram { | |
89 | struct ucc_slow_pram common; | |
90 | u8 res1[8]; /* reserved */ | |
91 | __be16 maxidl; /* Maximum idle chars */ | |
92 | __be16 idlc; /* temp idle counter */ | |
93 | __be16 brkcr; /* Break count register */ | |
94 | __be16 parec; /* receive parity error counter */ | |
95 | __be16 frmec; /* receive framing error counter */ | |
96 | __be16 nosec; /* receive noise counter */ | |
97 | __be16 brkec; /* receive break condition counter */ | |
98 | __be16 brkln; /* last received break length */ | |
99 | __be16 uaddr[2]; /* UART address character 1 & 2 */ | |
100 | __be16 rtemp; /* Temp storage */ | |
101 | __be16 toseq; /* Transmit out of sequence char */ | |
102 | __be16 cchars[8]; /* control characters 1-8 */ | |
103 | __be16 rccm; /* receive control character mask */ | |
104 | __be16 rccr; /* receive control character register */ | |
105 | __be16 rlbc; /* receive last break character */ | |
106 | __be16 res2; /* reserved */ | |
107 | __be32 res3; /* reserved, should be cleared */ | |
108 | u8 res4; /* reserved, should be cleared */ | |
109 | u8 res5[3]; /* reserved, should be cleared */ | |
110 | __be32 res6; /* reserved, should be cleared */ | |
111 | __be32 res7; /* reserved, should be cleared */ | |
112 | __be32 res8; /* reserved, should be cleared */ | |
113 | __be32 res9; /* reserved, should be cleared */ | |
114 | __be32 res10; /* reserved, should be cleared */ | |
115 | __be32 res11; /* reserved, should be cleared */ | |
116 | __be32 res12; /* reserved, should be cleared */ | |
117 | __be32 res13; /* reserved, should be cleared */ | |
118 | /* The rest is for Soft-UART only */ | |
119 | __be16 supsmr; /* 0x90, Shadow UPSMR */ | |
120 | __be16 res92; /* 0x92, reserved, initialize to 0 */ | |
121 | __be32 rx_state; /* 0x94, RX state, initialize to 0 */ | |
122 | __be32 rx_cnt; /* 0x98, RX count, initialize to 0 */ | |
123 | u8 rx_length; /* 0x9C, Char length, set to 1+CL+PEN+1+SL */ | |
124 | u8 rx_bitmark; /* 0x9D, reserved, initialize to 0 */ | |
125 | u8 rx_temp_dlst_qe; /* 0x9E, reserved, initialize to 0 */ | |
126 | u8 res14[0xBC - 0x9F]; /* reserved */ | |
127 | __be32 dump_ptr; /* 0xBC, Dump pointer */ | |
128 | __be32 rx_frame_rem; /* 0xC0, reserved, initialize to 0 */ | |
129 | u8 rx_frame_rem_size; /* 0xC4, reserved, initialize to 0 */ | |
130 | u8 tx_mode; /* 0xC5, mode, 0=AHDLC, 1=UART */ | |
131 | __be16 tx_state; /* 0xC6, TX state */ | |
132 | u8 res15[0xD0 - 0xC8]; /* reserved */ | |
133 | __be32 resD0; /* 0xD0, reserved, initialize to 0 */ | |
134 | u8 resD4; /* 0xD4, reserved, initialize to 0 */ | |
135 | __be16 resD5; /* 0xD5, reserved, initialize to 0 */ | |
136 | } __attribute__ ((packed)); | |
137 | ||
138 | /* SUPSMR definitions, for Soft-UART only */ | |
139 | #define UCC_UART_SUPSMR_SL 0x8000 | |
140 | #define UCC_UART_SUPSMR_RPM_MASK 0x6000 | |
141 | #define UCC_UART_SUPSMR_RPM_ODD 0x0000 | |
142 | #define UCC_UART_SUPSMR_RPM_LOW 0x2000 | |
143 | #define UCC_UART_SUPSMR_RPM_EVEN 0x4000 | |
144 | #define UCC_UART_SUPSMR_RPM_HIGH 0x6000 | |
145 | #define UCC_UART_SUPSMR_PEN 0x1000 | |
146 | #define UCC_UART_SUPSMR_TPM_MASK 0x0C00 | |
147 | #define UCC_UART_SUPSMR_TPM_ODD 0x0000 | |
148 | #define UCC_UART_SUPSMR_TPM_LOW 0x0400 | |
149 | #define UCC_UART_SUPSMR_TPM_EVEN 0x0800 | |
150 | #define UCC_UART_SUPSMR_TPM_HIGH 0x0C00 | |
151 | #define UCC_UART_SUPSMR_FRZ 0x0100 | |
152 | #define UCC_UART_SUPSMR_UM_MASK 0x00c0 | |
153 | #define UCC_UART_SUPSMR_UM_NORMAL 0x0000 | |
154 | #define UCC_UART_SUPSMR_UM_MAN_MULTI 0x0040 | |
155 | #define UCC_UART_SUPSMR_UM_AUTO_MULTI 0x00c0 | |
156 | #define UCC_UART_SUPSMR_CL_MASK 0x0030 | |
157 | #define UCC_UART_SUPSMR_CL_8 0x0030 | |
158 | #define UCC_UART_SUPSMR_CL_7 0x0020 | |
159 | #define UCC_UART_SUPSMR_CL_6 0x0010 | |
160 | #define UCC_UART_SUPSMR_CL_5 0x0000 | |
161 | ||
162 | #define UCC_UART_TX_STATE_AHDLC 0x00 | |
163 | #define UCC_UART_TX_STATE_UART 0x01 | |
164 | #define UCC_UART_TX_STATE_X1 0x00 | |
165 | #define UCC_UART_TX_STATE_X16 0x80 | |
166 | ||
167 | #define UCC_UART_PRAM_ALIGNMENT 0x100 | |
168 | ||
169 | #define UCC_UART_SIZE_OF_BD UCC_SLOW_SIZE_OF_BD | |
170 | #define NUM_CONTROL_CHARS 8 | |
171 | ||
172 | /* Private per-port data structure */ | |
173 | struct uart_qe_port { | |
174 | struct uart_port port; | |
175 | struct ucc_slow __iomem *uccp; | |
176 | struct ucc_uart_pram __iomem *uccup; | |
177 | struct ucc_slow_info us_info; | |
178 | struct ucc_slow_private *us_private; | |
179 | struct device_node *np; | |
180 | unsigned int ucc_num; /* First ucc is 0, not 1 */ | |
181 | ||
182 | u16 rx_nrfifos; | |
183 | u16 rx_fifosize; | |
184 | u16 tx_nrfifos; | |
185 | u16 tx_fifosize; | |
186 | int wait_closing; | |
187 | u32 flags; | |
188 | struct qe_bd *rx_bd_base; | |
189 | struct qe_bd *rx_cur; | |
190 | struct qe_bd *tx_bd_base; | |
191 | struct qe_bd *tx_cur; | |
192 | unsigned char *tx_buf; | |
193 | unsigned char *rx_buf; | |
194 | void *bd_virt; /* virtual address of the BD buffers */ | |
195 | dma_addr_t bd_dma_addr; /* bus address of the BD buffers */ | |
196 | unsigned int bd_size; /* size of BD buffer space */ | |
197 | }; | |
198 | ||
199 | static struct uart_driver ucc_uart_driver = { | |
200 | .owner = THIS_MODULE, | |
4feead71 | 201 | .driver_name = "ucc_uart", |
d7584ed2 TT |
202 | .dev_name = "ttyQE", |
203 | .major = SERIAL_QE_MAJOR, | |
204 | .minor = SERIAL_QE_MINOR, | |
205 | .nr = UCC_MAX_UART, | |
206 | }; | |
207 | ||
208 | /* | |
209 | * Virtual to physical address translation. | |
210 | * | |
211 | * Given the virtual address for a character buffer, this function returns | |
212 | * the physical (DMA) equivalent. | |
213 | */ | |
214 | static inline dma_addr_t cpu2qe_addr(void *addr, struct uart_qe_port *qe_port) | |
215 | { | |
216 | if (likely((addr >= qe_port->bd_virt)) && | |
217 | (addr < (qe_port->bd_virt + qe_port->bd_size))) | |
218 | return qe_port->bd_dma_addr + (addr - qe_port->bd_virt); | |
219 | ||
220 | /* something nasty happened */ | |
71cc2c21 | 221 | printk(KERN_ERR "%s: addr=%p\n", __func__, addr); |
d7584ed2 TT |
222 | BUG(); |
223 | return 0; | |
224 | } | |
225 | ||
226 | /* | |
227 | * Physical to virtual address translation. | |
228 | * | |
229 | * Given the physical (DMA) address for a character buffer, this function | |
230 | * returns the virtual equivalent. | |
231 | */ | |
232 | static inline void *qe2cpu_addr(dma_addr_t addr, struct uart_qe_port *qe_port) | |
233 | { | |
234 | /* sanity check */ | |
235 | if (likely((addr >= qe_port->bd_dma_addr) && | |
236 | (addr < (qe_port->bd_dma_addr + qe_port->bd_size)))) | |
237 | return qe_port->bd_virt + (addr - qe_port->bd_dma_addr); | |
238 | ||
239 | /* something nasty happened */ | |
181d5762 | 240 | printk(KERN_ERR "%s: addr=%llx\n", __func__, (u64)addr); |
d7584ed2 TT |
241 | BUG(); |
242 | return NULL; | |
243 | } | |
244 | ||
245 | /* | |
246 | * Return 1 if the QE is done transmitting all buffers for this port | |
247 | * | |
248 | * This function scans each BD in sequence. If we find a BD that is not | |
249 | * ready (READY=1), then we return 0 indicating that the QE is still sending | |
250 | * data. If we reach the last BD (WRAP=1), then we know we've scanned | |
251 | * the entire list, and all BDs are done. | |
252 | */ | |
253 | static unsigned int qe_uart_tx_empty(struct uart_port *port) | |
254 | { | |
255 | struct uart_qe_port *qe_port = | |
256 | container_of(port, struct uart_qe_port, port); | |
257 | struct qe_bd *bdp = qe_port->tx_bd_base; | |
258 | ||
259 | while (1) { | |
260 | if (in_be16(&bdp->status) & BD_SC_READY) | |
261 | /* This BD is not done, so return "not done" */ | |
262 | return 0; | |
263 | ||
264 | if (in_be16(&bdp->status) & BD_SC_WRAP) | |
265 | /* | |
266 | * This BD is done and it's the last one, so return | |
267 | * "done" | |
268 | */ | |
269 | return 1; | |
270 | ||
271 | bdp++; | |
272 | }; | |
273 | } | |
274 | ||
275 | /* | |
276 | * Set the modem control lines | |
277 | * | |
278 | * Although the QE can control the modem control lines (e.g. CTS), we | |
279 | * don't need that support. This function must exist, however, otherwise | |
280 | * the kernel will panic. | |
281 | */ | |
282 | void qe_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) | |
283 | { | |
284 | } | |
285 | ||
286 | /* | |
287 | * Get the current modem control line status | |
288 | * | |
289 | * Although the QE can control the modem control lines (e.g. CTS), this | |
290 | * driver currently doesn't support that, so we always return Carrier | |
291 | * Detect, Data Set Ready, and Clear To Send. | |
292 | */ | |
293 | static unsigned int qe_uart_get_mctrl(struct uart_port *port) | |
294 | { | |
295 | return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS; | |
296 | } | |
297 | ||
298 | /* | |
299 | * Disable the transmit interrupt. | |
300 | * | |
301 | * Although this function is called "stop_tx", it does not actually stop | |
302 | * transmission of data. Instead, it tells the QE to not generate an | |
303 | * interrupt when the UCC is finished sending characters. | |
304 | */ | |
305 | static void qe_uart_stop_tx(struct uart_port *port) | |
306 | { | |
307 | struct uart_qe_port *qe_port = | |
308 | container_of(port, struct uart_qe_port, port); | |
309 | ||
310 | clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX); | |
311 | } | |
312 | ||
313 | /* | |
314 | * Transmit as many characters to the HW as possible. | |
315 | * | |
316 | * This function will attempt to stuff of all the characters from the | |
317 | * kernel's transmit buffer into TX BDs. | |
318 | * | |
af901ca1 | 319 | * A return value of non-zero indicates that it successfully stuffed all |
d7584ed2 TT |
320 | * characters from the kernel buffer. |
321 | * | |
322 | * A return value of zero indicates that there are still characters in the | |
323 | * kernel's buffer that have not been transmitted, but there are no more BDs | |
324 | * available. This function should be called again after a BD has been made | |
325 | * available. | |
326 | */ | |
327 | static int qe_uart_tx_pump(struct uart_qe_port *qe_port) | |
328 | { | |
329 | struct qe_bd *bdp; | |
330 | unsigned char *p; | |
331 | unsigned int count; | |
332 | struct uart_port *port = &qe_port->port; | |
ebd2c8f6 | 333 | struct circ_buf *xmit = &port->state->xmit; |
d7584ed2 TT |
334 | |
335 | bdp = qe_port->rx_cur; | |
336 | ||
337 | /* Handle xon/xoff */ | |
338 | if (port->x_char) { | |
339 | /* Pick next descriptor and fill from buffer */ | |
340 | bdp = qe_port->tx_cur; | |
341 | ||
342 | p = qe2cpu_addr(bdp->buf, qe_port); | |
343 | ||
344 | *p++ = port->x_char; | |
345 | out_be16(&bdp->length, 1); | |
346 | setbits16(&bdp->status, BD_SC_READY); | |
347 | /* Get next BD. */ | |
348 | if (in_be16(&bdp->status) & BD_SC_WRAP) | |
349 | bdp = qe_port->tx_bd_base; | |
350 | else | |
351 | bdp++; | |
352 | qe_port->tx_cur = bdp; | |
353 | ||
354 | port->icount.tx++; | |
355 | port->x_char = 0; | |
356 | return 1; | |
357 | } | |
358 | ||
359 | if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { | |
360 | qe_uart_stop_tx(port); | |
361 | return 0; | |
362 | } | |
363 | ||
364 | /* Pick next descriptor and fill from buffer */ | |
365 | bdp = qe_port->tx_cur; | |
366 | ||
367 | while (!(in_be16(&bdp->status) & BD_SC_READY) && | |
368 | (xmit->tail != xmit->head)) { | |
369 | count = 0; | |
370 | p = qe2cpu_addr(bdp->buf, qe_port); | |
371 | while (count < qe_port->tx_fifosize) { | |
372 | *p++ = xmit->buf[xmit->tail]; | |
373 | xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); | |
374 | port->icount.tx++; | |
375 | count++; | |
376 | if (xmit->head == xmit->tail) | |
377 | break; | |
378 | } | |
379 | ||
380 | out_be16(&bdp->length, count); | |
381 | setbits16(&bdp->status, BD_SC_READY); | |
382 | ||
383 | /* Get next BD. */ | |
384 | if (in_be16(&bdp->status) & BD_SC_WRAP) | |
385 | bdp = qe_port->tx_bd_base; | |
386 | else | |
387 | bdp++; | |
388 | } | |
389 | qe_port->tx_cur = bdp; | |
390 | ||
391 | if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) | |
392 | uart_write_wakeup(port); | |
393 | ||
394 | if (uart_circ_empty(xmit)) { | |
395 | /* The kernel buffer is empty, so turn off TX interrupts. We | |
396 | don't need to be told when the QE is finished transmitting | |
397 | the data. */ | |
398 | qe_uart_stop_tx(port); | |
399 | return 0; | |
400 | } | |
401 | ||
402 | return 1; | |
403 | } | |
404 | ||
405 | /* | |
406 | * Start transmitting data | |
407 | * | |
408 | * This function will start transmitting any available data, if the port | |
409 | * isn't already transmitting data. | |
410 | */ | |
411 | static void qe_uart_start_tx(struct uart_port *port) | |
412 | { | |
413 | struct uart_qe_port *qe_port = | |
414 | container_of(port, struct uart_qe_port, port); | |
415 | ||
416 | /* If we currently are transmitting, then just return */ | |
417 | if (in_be16(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX) | |
418 | return; | |
419 | ||
420 | /* Otherwise, pump the port and start transmission */ | |
421 | if (qe_uart_tx_pump(qe_port)) | |
422 | setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX); | |
423 | } | |
424 | ||
425 | /* | |
426 | * Stop transmitting data | |
427 | */ | |
428 | static void qe_uart_stop_rx(struct uart_port *port) | |
429 | { | |
430 | struct uart_qe_port *qe_port = | |
431 | container_of(port, struct uart_qe_port, port); | |
432 | ||
433 | clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX); | |
434 | } | |
435 | ||
436 | /* | |
437 | * Enable status change interrupts | |
438 | * | |
439 | * We don't support status change interrupts, but we need to define this | |
440 | * function otherwise the kernel will panic. | |
441 | */ | |
442 | static void qe_uart_enable_ms(struct uart_port *port) | |
443 | { | |
444 | } | |
445 | ||
446 | /* Start or stop sending break signal | |
447 | * | |
448 | * This function controls the sending of a break signal. If break_state=1, | |
449 | * then we start sending a break signal. If break_state=0, then we stop | |
450 | * sending the break signal. | |
451 | */ | |
452 | static void qe_uart_break_ctl(struct uart_port *port, int break_state) | |
453 | { | |
454 | struct uart_qe_port *qe_port = | |
455 | container_of(port, struct uart_qe_port, port); | |
456 | ||
457 | if (break_state) | |
458 | ucc_slow_stop_tx(qe_port->us_private); | |
459 | else | |
460 | ucc_slow_restart_tx(qe_port->us_private); | |
461 | } | |
462 | ||
463 | /* ISR helper function for receiving character. | |
464 | * | |
465 | * This function is called by the ISR to handling receiving characters | |
466 | */ | |
467 | static void qe_uart_int_rx(struct uart_qe_port *qe_port) | |
468 | { | |
469 | int i; | |
470 | unsigned char ch, *cp; | |
471 | struct uart_port *port = &qe_port->port; | |
ebd2c8f6 | 472 | struct tty_struct *tty = port->state->port.tty; |
d7584ed2 TT |
473 | struct qe_bd *bdp; |
474 | u16 status; | |
475 | unsigned int flg; | |
476 | ||
477 | /* Just loop through the closed BDs and copy the characters into | |
478 | * the buffer. | |
479 | */ | |
480 | bdp = qe_port->rx_cur; | |
481 | while (1) { | |
482 | status = in_be16(&bdp->status); | |
483 | ||
484 | /* If this one is empty, then we assume we've read them all */ | |
485 | if (status & BD_SC_EMPTY) | |
486 | break; | |
487 | ||
488 | /* get number of characters, and check space in RX buffer */ | |
489 | i = in_be16(&bdp->length); | |
490 | ||
491 | /* If we don't have enough room in RX buffer for the entire BD, | |
492 | * then we try later, which will be the next RX interrupt. | |
493 | */ | |
494 | if (tty_buffer_request_room(tty, i) < i) { | |
495 | dev_dbg(port->dev, "ucc-uart: no room in RX buffer\n"); | |
496 | return; | |
497 | } | |
498 | ||
499 | /* get pointer */ | |
500 | cp = qe2cpu_addr(bdp->buf, qe_port); | |
501 | ||
502 | /* loop through the buffer */ | |
503 | while (i-- > 0) { | |
504 | ch = *cp++; | |
505 | port->icount.rx++; | |
506 | flg = TTY_NORMAL; | |
507 | ||
508 | if (!i && status & | |
509 | (BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV)) | |
510 | goto handle_error; | |
511 | if (uart_handle_sysrq_char(port, ch)) | |
512 | continue; | |
513 | ||
514 | error_return: | |
515 | tty_insert_flip_char(tty, ch, flg); | |
516 | ||
517 | } | |
518 | ||
519 | /* This BD is ready to be used again. Clear status. get next */ | |
520 | clrsetbits_be16(&bdp->status, BD_SC_BR | BD_SC_FR | BD_SC_PR | | |
521 | BD_SC_OV | BD_SC_ID, BD_SC_EMPTY); | |
522 | if (in_be16(&bdp->status) & BD_SC_WRAP) | |
523 | bdp = qe_port->rx_bd_base; | |
524 | else | |
525 | bdp++; | |
526 | ||
527 | } | |
528 | ||
529 | /* Write back buffer pointer */ | |
530 | qe_port->rx_cur = bdp; | |
531 | ||
532 | /* Activate BH processing */ | |
533 | tty_flip_buffer_push(tty); | |
534 | ||
535 | return; | |
536 | ||
537 | /* Error processing */ | |
538 | ||
539 | handle_error: | |
540 | /* Statistics */ | |
541 | if (status & BD_SC_BR) | |
542 | port->icount.brk++; | |
543 | if (status & BD_SC_PR) | |
544 | port->icount.parity++; | |
545 | if (status & BD_SC_FR) | |
546 | port->icount.frame++; | |
547 | if (status & BD_SC_OV) | |
548 | port->icount.overrun++; | |
549 | ||
550 | /* Mask out ignored conditions */ | |
551 | status &= port->read_status_mask; | |
552 | ||
553 | /* Handle the remaining ones */ | |
554 | if (status & BD_SC_BR) | |
555 | flg = TTY_BREAK; | |
556 | else if (status & BD_SC_PR) | |
557 | flg = TTY_PARITY; | |
558 | else if (status & BD_SC_FR) | |
559 | flg = TTY_FRAME; | |
560 | ||
561 | /* Overrun does not affect the current character ! */ | |
562 | if (status & BD_SC_OV) | |
563 | tty_insert_flip_char(tty, 0, TTY_OVERRUN); | |
564 | #ifdef SUPPORT_SYSRQ | |
565 | port->sysrq = 0; | |
566 | #endif | |
567 | goto error_return; | |
568 | } | |
569 | ||
570 | /* Interrupt handler | |
571 | * | |
572 | * This interrupt handler is called after a BD is processed. | |
573 | */ | |
574 | static irqreturn_t qe_uart_int(int irq, void *data) | |
575 | { | |
576 | struct uart_qe_port *qe_port = (struct uart_qe_port *) data; | |
577 | struct ucc_slow __iomem *uccp = qe_port->uccp; | |
578 | u16 events; | |
579 | ||
580 | /* Clear the interrupts */ | |
581 | events = in_be16(&uccp->ucce); | |
582 | out_be16(&uccp->ucce, events); | |
583 | ||
584 | if (events & UCC_UART_UCCE_BRKE) | |
585 | uart_handle_break(&qe_port->port); | |
586 | ||
587 | if (events & UCC_UART_UCCE_RX) | |
588 | qe_uart_int_rx(qe_port); | |
589 | ||
590 | if (events & UCC_UART_UCCE_TX) | |
591 | qe_uart_tx_pump(qe_port); | |
592 | ||
593 | return events ? IRQ_HANDLED : IRQ_NONE; | |
594 | } | |
595 | ||
596 | /* Initialize buffer descriptors | |
597 | * | |
598 | * This function initializes all of the RX and TX buffer descriptors. | |
599 | */ | |
600 | static void qe_uart_initbd(struct uart_qe_port *qe_port) | |
601 | { | |
602 | int i; | |
603 | void *bd_virt; | |
604 | struct qe_bd *bdp; | |
605 | ||
606 | /* Set the physical address of the host memory buffers in the buffer | |
607 | * descriptors, and the virtual address for us to work with. | |
608 | */ | |
609 | bd_virt = qe_port->bd_virt; | |
610 | bdp = qe_port->rx_bd_base; | |
611 | qe_port->rx_cur = qe_port->rx_bd_base; | |
612 | for (i = 0; i < (qe_port->rx_nrfifos - 1); i++) { | |
613 | out_be16(&bdp->status, BD_SC_EMPTY | BD_SC_INTRPT); | |
614 | out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); | |
615 | out_be16(&bdp->length, 0); | |
616 | bd_virt += qe_port->rx_fifosize; | |
617 | bdp++; | |
618 | } | |
619 | ||
620 | /* */ | |
621 | out_be16(&bdp->status, BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT); | |
622 | out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); | |
623 | out_be16(&bdp->length, 0); | |
624 | ||
625 | /* Set the physical address of the host memory | |
626 | * buffers in the buffer descriptors, and the | |
627 | * virtual address for us to work with. | |
628 | */ | |
629 | bd_virt = qe_port->bd_virt + | |
630 | L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize); | |
631 | qe_port->tx_cur = qe_port->tx_bd_base; | |
632 | bdp = qe_port->tx_bd_base; | |
633 | for (i = 0; i < (qe_port->tx_nrfifos - 1); i++) { | |
634 | out_be16(&bdp->status, BD_SC_INTRPT); | |
635 | out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); | |
636 | out_be16(&bdp->length, 0); | |
637 | bd_virt += qe_port->tx_fifosize; | |
638 | bdp++; | |
639 | } | |
640 | ||
641 | /* Loopback requires the preamble bit to be set on the first TX BD */ | |
642 | #ifdef LOOPBACK | |
643 | setbits16(&qe_port->tx_cur->status, BD_SC_P); | |
644 | #endif | |
645 | ||
646 | out_be16(&bdp->status, BD_SC_WRAP | BD_SC_INTRPT); | |
647 | out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); | |
648 | out_be16(&bdp->length, 0); | |
649 | } | |
650 | ||
651 | /* | |
652 | * Initialize a UCC for UART. | |
653 | * | |
654 | * This function configures a given UCC to be used as a UART device. Basic | |
655 | * UCC initialization is handled in qe_uart_request_port(). This function | |
656 | * does all the UART-specific stuff. | |
657 | */ | |
658 | static void qe_uart_init_ucc(struct uart_qe_port *qe_port) | |
659 | { | |
660 | u32 cecr_subblock; | |
661 | struct ucc_slow __iomem *uccp = qe_port->uccp; | |
662 | struct ucc_uart_pram *uccup = qe_port->uccup; | |
663 | ||
664 | unsigned int i; | |
665 | ||
666 | /* First, disable TX and RX in the UCC */ | |
667 | ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX); | |
668 | ||
669 | /* Program the UCC UART parameter RAM */ | |
670 | out_8(&uccup->common.rbmr, UCC_BMR_GBL | UCC_BMR_BO_BE); | |
671 | out_8(&uccup->common.tbmr, UCC_BMR_GBL | UCC_BMR_BO_BE); | |
672 | out_be16(&uccup->common.mrblr, qe_port->rx_fifosize); | |
673 | out_be16(&uccup->maxidl, 0x10); | |
674 | out_be16(&uccup->brkcr, 1); | |
675 | out_be16(&uccup->parec, 0); | |
676 | out_be16(&uccup->frmec, 0); | |
677 | out_be16(&uccup->nosec, 0); | |
678 | out_be16(&uccup->brkec, 0); | |
679 | out_be16(&uccup->uaddr[0], 0); | |
680 | out_be16(&uccup->uaddr[1], 0); | |
681 | out_be16(&uccup->toseq, 0); | |
682 | for (i = 0; i < 8; i++) | |
683 | out_be16(&uccup->cchars[i], 0xC000); | |
684 | out_be16(&uccup->rccm, 0xc0ff); | |
685 | ||
686 | /* Configure the GUMR registers for UART */ | |
b45cc9ef | 687 | if (soft_uart) { |
d7584ed2 TT |
688 | /* Soft-UART requires a 1X multiplier for TX */ |
689 | clrsetbits_be32(&uccp->gumr_l, | |
690 | UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | | |
691 | UCC_SLOW_GUMR_L_RDCR_MASK, | |
692 | UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 | | |
693 | UCC_SLOW_GUMR_L_RDCR_16); | |
b45cc9ef DL |
694 | |
695 | clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW, | |
696 | UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX); | |
697 | } else { | |
d7584ed2 TT |
698 | clrsetbits_be32(&uccp->gumr_l, |
699 | UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | | |
700 | UCC_SLOW_GUMR_L_RDCR_MASK, | |
701 | UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 | | |
702 | UCC_SLOW_GUMR_L_RDCR_16); | |
703 | ||
b45cc9ef DL |
704 | clrsetbits_be32(&uccp->gumr_h, |
705 | UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX, | |
706 | UCC_SLOW_GUMR_H_RFW); | |
707 | } | |
d7584ed2 TT |
708 | |
709 | #ifdef LOOPBACK | |
710 | clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK, | |
711 | UCC_SLOW_GUMR_L_DIAG_LOOP); | |
712 | clrsetbits_be32(&uccp->gumr_h, | |
713 | UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_RSYN, | |
714 | UCC_SLOW_GUMR_H_CDS); | |
715 | #endif | |
716 | ||
b45cc9ef | 717 | /* Disable rx interrupts and clear all pending events. */ |
d7584ed2 TT |
718 | out_be16(&uccp->uccm, 0); |
719 | out_be16(&uccp->ucce, 0xffff); | |
720 | out_be16(&uccp->udsr, 0x7e7e); | |
721 | ||
722 | /* Initialize UPSMR */ | |
723 | out_be16(&uccp->upsmr, 0); | |
724 | ||
725 | if (soft_uart) { | |
726 | out_be16(&uccup->supsmr, 0x30); | |
727 | out_be16(&uccup->res92, 0); | |
728 | out_be32(&uccup->rx_state, 0); | |
729 | out_be32(&uccup->rx_cnt, 0); | |
730 | out_8(&uccup->rx_bitmark, 0); | |
731 | out_8(&uccup->rx_length, 10); | |
732 | out_be32(&uccup->dump_ptr, 0x4000); | |
733 | out_8(&uccup->rx_temp_dlst_qe, 0); | |
734 | out_be32(&uccup->rx_frame_rem, 0); | |
735 | out_8(&uccup->rx_frame_rem_size, 0); | |
736 | /* Soft-UART requires TX to be 1X */ | |
737 | out_8(&uccup->tx_mode, | |
738 | UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1); | |
739 | out_be16(&uccup->tx_state, 0); | |
740 | out_8(&uccup->resD4, 0); | |
741 | out_be16(&uccup->resD5, 0); | |
742 | ||
743 | /* Set UART mode. | |
744 | * Enable receive and transmit. | |
745 | */ | |
746 | ||
747 | /* From the microcode errata: | |
748 | * 1.GUMR_L register, set mode=0010 (QMC). | |
749 | * 2.Set GUMR_H[17] bit. (UART/AHDLC mode). | |
750 | * 3.Set GUMR_H[19:20] (Transparent mode) | |
751 | * 4.Clear GUMR_H[26] (RFW) | |
752 | * ... | |
753 | * 6.Receiver must use 16x over sampling | |
754 | */ | |
755 | clrsetbits_be32(&uccp->gumr_l, | |
756 | UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | | |
757 | UCC_SLOW_GUMR_L_RDCR_MASK, | |
758 | UCC_SLOW_GUMR_L_MODE_QMC | UCC_SLOW_GUMR_L_TDCR_16 | | |
759 | UCC_SLOW_GUMR_L_RDCR_16); | |
760 | ||
761 | clrsetbits_be32(&uccp->gumr_h, | |
762 | UCC_SLOW_GUMR_H_RFW | UCC_SLOW_GUMR_H_RSYN, | |
763 | UCC_SLOW_GUMR_H_SUART | UCC_SLOW_GUMR_H_TRX | | |
764 | UCC_SLOW_GUMR_H_TTX | UCC_SLOW_GUMR_H_TFL); | |
765 | ||
766 | #ifdef LOOPBACK | |
767 | clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK, | |
768 | UCC_SLOW_GUMR_L_DIAG_LOOP); | |
769 | clrbits32(&uccp->gumr_h, UCC_SLOW_GUMR_H_CTSP | | |
770 | UCC_SLOW_GUMR_H_CDS); | |
771 | #endif | |
772 | ||
773 | cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num); | |
774 | qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock, | |
775 | QE_CR_PROTOCOL_UNSPECIFIED, 0); | |
b45cc9ef DL |
776 | } else { |
777 | cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num); | |
778 | qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock, | |
779 | QE_CR_PROTOCOL_UART, 0); | |
d7584ed2 TT |
780 | } |
781 | } | |
782 | ||
783 | /* | |
784 | * Initialize the port. | |
785 | */ | |
786 | static int qe_uart_startup(struct uart_port *port) | |
787 | { | |
788 | struct uart_qe_port *qe_port = | |
789 | container_of(port, struct uart_qe_port, port); | |
790 | int ret; | |
791 | ||
792 | /* | |
793 | * If we're using Soft-UART mode, then we need to make sure the | |
794 | * firmware has been uploaded first. | |
795 | */ | |
796 | if (soft_uart && !firmware_loaded) { | |
797 | dev_err(port->dev, "Soft-UART firmware not uploaded\n"); | |
798 | return -ENODEV; | |
799 | } | |
800 | ||
801 | qe_uart_initbd(qe_port); | |
802 | qe_uart_init_ucc(qe_port); | |
803 | ||
804 | /* Install interrupt handler. */ | |
805 | ret = request_irq(port->irq, qe_uart_int, IRQF_SHARED, "ucc-uart", | |
806 | qe_port); | |
807 | if (ret) { | |
808 | dev_err(port->dev, "could not claim IRQ %u\n", port->irq); | |
809 | return ret; | |
810 | } | |
811 | ||
812 | /* Startup rx-int */ | |
813 | setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX); | |
814 | ucc_slow_enable(qe_port->us_private, COMM_DIR_RX_AND_TX); | |
815 | ||
816 | return 0; | |
817 | } | |
818 | ||
819 | /* | |
820 | * Shutdown the port. | |
821 | */ | |
822 | static void qe_uart_shutdown(struct uart_port *port) | |
823 | { | |
824 | struct uart_qe_port *qe_port = | |
825 | container_of(port, struct uart_qe_port, port); | |
826 | struct ucc_slow __iomem *uccp = qe_port->uccp; | |
827 | unsigned int timeout = 20; | |
828 | ||
829 | /* Disable RX and TX */ | |
830 | ||
831 | /* Wait for all the BDs marked sent */ | |
832 | while (!qe_uart_tx_empty(port)) { | |
833 | if (!--timeout) { | |
834 | dev_warn(port->dev, "shutdown timeout\n"); | |
835 | break; | |
836 | } | |
837 | set_current_state(TASK_UNINTERRUPTIBLE); | |
838 | schedule_timeout(2); | |
839 | } | |
840 | ||
841 | if (qe_port->wait_closing) { | |
842 | /* Wait a bit longer */ | |
843 | set_current_state(TASK_UNINTERRUPTIBLE); | |
844 | schedule_timeout(qe_port->wait_closing); | |
845 | } | |
846 | ||
847 | /* Stop uarts */ | |
848 | ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX); | |
849 | clrbits16(&uccp->uccm, UCC_UART_UCCE_TX | UCC_UART_UCCE_RX); | |
850 | ||
851 | /* Shut them really down and reinit buffer descriptors */ | |
852 | ucc_slow_graceful_stop_tx(qe_port->us_private); | |
853 | qe_uart_initbd(qe_port); | |
854 | ||
855 | free_irq(port->irq, qe_port); | |
856 | } | |
857 | ||
858 | /* | |
859 | * Set the serial port parameters. | |
860 | */ | |
861 | static void qe_uart_set_termios(struct uart_port *port, | |
862 | struct ktermios *termios, struct ktermios *old) | |
863 | { | |
864 | struct uart_qe_port *qe_port = | |
865 | container_of(port, struct uart_qe_port, port); | |
866 | struct ucc_slow __iomem *uccp = qe_port->uccp; | |
867 | unsigned int baud; | |
868 | unsigned long flags; | |
869 | u16 upsmr = in_be16(&uccp->upsmr); | |
870 | struct ucc_uart_pram __iomem *uccup = qe_port->uccup; | |
871 | u16 supsmr = in_be16(&uccup->supsmr); | |
872 | u8 char_length = 2; /* 1 + CL + PEN + 1 + SL */ | |
873 | ||
874 | /* Character length programmed into the mode register is the | |
875 | * sum of: 1 start bit, number of data bits, 0 or 1 parity bit, | |
876 | * 1 or 2 stop bits, minus 1. | |
877 | * The value 'bits' counts this for us. | |
878 | */ | |
879 | ||
880 | /* byte size */ | |
881 | upsmr &= UCC_UART_UPSMR_CL_MASK; | |
882 | supsmr &= UCC_UART_SUPSMR_CL_MASK; | |
883 | ||
884 | switch (termios->c_cflag & CSIZE) { | |
885 | case CS5: | |
886 | upsmr |= UCC_UART_UPSMR_CL_5; | |
887 | supsmr |= UCC_UART_SUPSMR_CL_5; | |
888 | char_length += 5; | |
889 | break; | |
890 | case CS6: | |
891 | upsmr |= UCC_UART_UPSMR_CL_6; | |
892 | supsmr |= UCC_UART_SUPSMR_CL_6; | |
893 | char_length += 6; | |
894 | break; | |
895 | case CS7: | |
896 | upsmr |= UCC_UART_UPSMR_CL_7; | |
897 | supsmr |= UCC_UART_SUPSMR_CL_7; | |
898 | char_length += 7; | |
899 | break; | |
900 | default: /* case CS8 */ | |
901 | upsmr |= UCC_UART_UPSMR_CL_8; | |
902 | supsmr |= UCC_UART_SUPSMR_CL_8; | |
903 | char_length += 8; | |
904 | break; | |
905 | } | |
906 | ||
907 | /* If CSTOPB is set, we want two stop bits */ | |
908 | if (termios->c_cflag & CSTOPB) { | |
909 | upsmr |= UCC_UART_UPSMR_SL; | |
910 | supsmr |= UCC_UART_SUPSMR_SL; | |
911 | char_length++; /* + SL */ | |
912 | } | |
913 | ||
914 | if (termios->c_cflag & PARENB) { | |
915 | upsmr |= UCC_UART_UPSMR_PEN; | |
916 | supsmr |= UCC_UART_SUPSMR_PEN; | |
917 | char_length++; /* + PEN */ | |
918 | ||
919 | if (!(termios->c_cflag & PARODD)) { | |
920 | upsmr &= ~(UCC_UART_UPSMR_RPM_MASK | | |
921 | UCC_UART_UPSMR_TPM_MASK); | |
922 | upsmr |= UCC_UART_UPSMR_RPM_EVEN | | |
923 | UCC_UART_UPSMR_TPM_EVEN; | |
924 | supsmr &= ~(UCC_UART_SUPSMR_RPM_MASK | | |
925 | UCC_UART_SUPSMR_TPM_MASK); | |
926 | supsmr |= UCC_UART_SUPSMR_RPM_EVEN | | |
927 | UCC_UART_SUPSMR_TPM_EVEN; | |
928 | } | |
929 | } | |
930 | ||
931 | /* | |
932 | * Set up parity check flag | |
933 | */ | |
934 | port->read_status_mask = BD_SC_EMPTY | BD_SC_OV; | |
935 | if (termios->c_iflag & INPCK) | |
936 | port->read_status_mask |= BD_SC_FR | BD_SC_PR; | |
937 | if (termios->c_iflag & (BRKINT | PARMRK)) | |
938 | port->read_status_mask |= BD_SC_BR; | |
939 | ||
940 | /* | |
941 | * Characters to ignore | |
942 | */ | |
943 | port->ignore_status_mask = 0; | |
944 | if (termios->c_iflag & IGNPAR) | |
945 | port->ignore_status_mask |= BD_SC_PR | BD_SC_FR; | |
946 | if (termios->c_iflag & IGNBRK) { | |
947 | port->ignore_status_mask |= BD_SC_BR; | |
948 | /* | |
949 | * If we're ignore parity and break indicators, ignore | |
950 | * overruns too. (For real raw support). | |
951 | */ | |
952 | if (termios->c_iflag & IGNPAR) | |
953 | port->ignore_status_mask |= BD_SC_OV; | |
954 | } | |
955 | /* | |
956 | * !!! ignore all characters if CREAD is not set | |
957 | */ | |
958 | if ((termios->c_cflag & CREAD) == 0) | |
959 | port->read_status_mask &= ~BD_SC_EMPTY; | |
960 | ||
961 | baud = uart_get_baud_rate(port, termios, old, 0, 115200); | |
962 | ||
963 | /* Do we really need a spinlock here? */ | |
964 | spin_lock_irqsave(&port->lock, flags); | |
965 | ||
8e18862d CM |
966 | /* Update the per-port timeout. */ |
967 | uart_update_timeout(port, termios->c_cflag, baud); | |
968 | ||
d7584ed2 TT |
969 | out_be16(&uccp->upsmr, upsmr); |
970 | if (soft_uart) { | |
971 | out_be16(&uccup->supsmr, supsmr); | |
972 | out_8(&uccup->rx_length, char_length); | |
973 | ||
974 | /* Soft-UART requires a 1X multiplier for TX */ | |
975 | qe_setbrg(qe_port->us_info.rx_clock, baud, 16); | |
976 | qe_setbrg(qe_port->us_info.tx_clock, baud, 1); | |
977 | } else { | |
978 | qe_setbrg(qe_port->us_info.rx_clock, baud, 16); | |
979 | qe_setbrg(qe_port->us_info.tx_clock, baud, 16); | |
980 | } | |
981 | ||
982 | spin_unlock_irqrestore(&port->lock, flags); | |
983 | } | |
984 | ||
985 | /* | |
986 | * Return a pointer to a string that describes what kind of port this is. | |
987 | */ | |
988 | static const char *qe_uart_type(struct uart_port *port) | |
989 | { | |
990 | return "QE"; | |
991 | } | |
992 | ||
993 | /* | |
994 | * Allocate any memory and I/O resources required by the port. | |
995 | */ | |
996 | static int qe_uart_request_port(struct uart_port *port) | |
997 | { | |
998 | int ret; | |
999 | struct uart_qe_port *qe_port = | |
1000 | container_of(port, struct uart_qe_port, port); | |
1001 | struct ucc_slow_info *us_info = &qe_port->us_info; | |
1002 | struct ucc_slow_private *uccs; | |
1003 | unsigned int rx_size, tx_size; | |
1004 | void *bd_virt; | |
1005 | dma_addr_t bd_dma_addr = 0; | |
1006 | ||
1007 | ret = ucc_slow_init(us_info, &uccs); | |
1008 | if (ret) { | |
1009 | dev_err(port->dev, "could not initialize UCC%u\n", | |
1010 | qe_port->ucc_num); | |
1011 | return ret; | |
1012 | } | |
1013 | ||
1014 | qe_port->us_private = uccs; | |
1015 | qe_port->uccp = uccs->us_regs; | |
1016 | qe_port->uccup = (struct ucc_uart_pram *) uccs->us_pram; | |
1017 | qe_port->rx_bd_base = uccs->rx_bd; | |
1018 | qe_port->tx_bd_base = uccs->tx_bd; | |
1019 | ||
1020 | /* | |
1021 | * Allocate the transmit and receive data buffers. | |
1022 | */ | |
1023 | ||
1024 | rx_size = L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize); | |
1025 | tx_size = L1_CACHE_ALIGN(qe_port->tx_nrfifos * qe_port->tx_fifosize); | |
1026 | ||
8b05cefc | 1027 | bd_virt = dma_alloc_coherent(port->dev, rx_size + tx_size, &bd_dma_addr, |
d7584ed2 TT |
1028 | GFP_KERNEL); |
1029 | if (!bd_virt) { | |
1030 | dev_err(port->dev, "could not allocate buffer descriptors\n"); | |
1031 | return -ENOMEM; | |
1032 | } | |
1033 | ||
1034 | qe_port->bd_virt = bd_virt; | |
1035 | qe_port->bd_dma_addr = bd_dma_addr; | |
1036 | qe_port->bd_size = rx_size + tx_size; | |
1037 | ||
1038 | qe_port->rx_buf = bd_virt; | |
1039 | qe_port->tx_buf = qe_port->rx_buf + rx_size; | |
1040 | ||
1041 | return 0; | |
1042 | } | |
1043 | ||
1044 | /* | |
1045 | * Configure the port. | |
1046 | * | |
1047 | * We say we're a CPM-type port because that's mostly true. Once the device | |
1048 | * is configured, this driver operates almost identically to the CPM serial | |
1049 | * driver. | |
1050 | */ | |
1051 | static void qe_uart_config_port(struct uart_port *port, int flags) | |
1052 | { | |
1053 | if (flags & UART_CONFIG_TYPE) { | |
1054 | port->type = PORT_CPM; | |
1055 | qe_uart_request_port(port); | |
1056 | } | |
1057 | } | |
1058 | ||
1059 | /* | |
1060 | * Release any memory and I/O resources that were allocated in | |
1061 | * qe_uart_request_port(). | |
1062 | */ | |
1063 | static void qe_uart_release_port(struct uart_port *port) | |
1064 | { | |
1065 | struct uart_qe_port *qe_port = | |
1066 | container_of(port, struct uart_qe_port, port); | |
1067 | struct ucc_slow_private *uccs = qe_port->us_private; | |
1068 | ||
8b05cefc | 1069 | dma_free_coherent(port->dev, qe_port->bd_size, qe_port->bd_virt, |
d7584ed2 TT |
1070 | qe_port->bd_dma_addr); |
1071 | ||
1072 | ucc_slow_free(uccs); | |
1073 | } | |
1074 | ||
1075 | /* | |
1076 | * Verify that the data in serial_struct is suitable for this device. | |
1077 | */ | |
1078 | static int qe_uart_verify_port(struct uart_port *port, | |
1079 | struct serial_struct *ser) | |
1080 | { | |
1081 | if (ser->type != PORT_UNKNOWN && ser->type != PORT_CPM) | |
1082 | return -EINVAL; | |
1083 | ||
a62c4133 | 1084 | if (ser->irq < 0 || ser->irq >= nr_irqs) |
d7584ed2 TT |
1085 | return -EINVAL; |
1086 | ||
1087 | if (ser->baud_base < 9600) | |
1088 | return -EINVAL; | |
1089 | ||
1090 | return 0; | |
1091 | } | |
1092 | /* UART operations | |
1093 | * | |
1094 | * Details on these functions can be found in Documentation/serial/driver | |
1095 | */ | |
1096 | static struct uart_ops qe_uart_pops = { | |
1097 | .tx_empty = qe_uart_tx_empty, | |
1098 | .set_mctrl = qe_uart_set_mctrl, | |
1099 | .get_mctrl = qe_uart_get_mctrl, | |
1100 | .stop_tx = qe_uart_stop_tx, | |
1101 | .start_tx = qe_uart_start_tx, | |
1102 | .stop_rx = qe_uart_stop_rx, | |
1103 | .enable_ms = qe_uart_enable_ms, | |
1104 | .break_ctl = qe_uart_break_ctl, | |
1105 | .startup = qe_uart_startup, | |
1106 | .shutdown = qe_uart_shutdown, | |
1107 | .set_termios = qe_uart_set_termios, | |
1108 | .type = qe_uart_type, | |
1109 | .release_port = qe_uart_release_port, | |
1110 | .request_port = qe_uart_request_port, | |
1111 | .config_port = qe_uart_config_port, | |
1112 | .verify_port = qe_uart_verify_port, | |
1113 | }; | |
1114 | ||
1115 | /* | |
1116 | * Obtain the SOC model number and revision level | |
1117 | * | |
1118 | * This function parses the device tree to obtain the SOC model. It then | |
1119 | * reads the SVR register to the revision. | |
1120 | * | |
1121 | * The device tree stores the SOC model two different ways. | |
1122 | * | |
1123 | * The new way is: | |
1124 | * | |
1125 | * cpu@0 { | |
1126 | * compatible = "PowerPC,8323"; | |
1127 | * device_type = "cpu"; | |
1128 | * ... | |
1129 | * | |
1130 | * | |
1131 | * The old way is: | |
1132 | * PowerPC,8323@0 { | |
1133 | * device_type = "cpu"; | |
1134 | * ... | |
1135 | * | |
1136 | * This code first checks the new way, and then the old way. | |
1137 | */ | |
1138 | static unsigned int soc_info(unsigned int *rev_h, unsigned int *rev_l) | |
1139 | { | |
1140 | struct device_node *np; | |
1141 | const char *soc_string; | |
1142 | unsigned int svr; | |
1143 | unsigned int soc; | |
1144 | ||
1145 | /* Find the CPU node */ | |
1146 | np = of_find_node_by_type(NULL, "cpu"); | |
1147 | if (!np) | |
1148 | return 0; | |
1149 | /* Find the compatible property */ | |
1150 | soc_string = of_get_property(np, "compatible", NULL); | |
1151 | if (!soc_string) | |
1152 | /* No compatible property, so try the name. */ | |
1153 | soc_string = np->name; | |
1154 | ||
1155 | /* Extract the SOC number from the "PowerPC," string */ | |
1156 | if ((sscanf(soc_string, "PowerPC,%u", &soc) != 1) || !soc) | |
1157 | return 0; | |
1158 | ||
1159 | /* Get the revision from the SVR */ | |
1160 | svr = mfspr(SPRN_SVR); | |
1161 | *rev_h = (svr >> 4) & 0xf; | |
1162 | *rev_l = svr & 0xf; | |
1163 | ||
1164 | return soc; | |
1165 | } | |
1166 | ||
1167 | /* | |
1168 | * requst_firmware_nowait() callback function | |
1169 | * | |
1170 | * This function is called by the kernel when a firmware is made available, | |
1171 | * or if it times out waiting for the firmware. | |
1172 | */ | |
1173 | static void uart_firmware_cont(const struct firmware *fw, void *context) | |
1174 | { | |
1175 | struct qe_firmware *firmware; | |
1176 | struct device *dev = context; | |
1177 | int ret; | |
1178 | ||
1179 | if (!fw) { | |
1180 | dev_err(dev, "firmware not found\n"); | |
1181 | return; | |
1182 | } | |
1183 | ||
1184 | firmware = (struct qe_firmware *) fw->data; | |
1185 | ||
1186 | if (firmware->header.length != fw->size) { | |
1187 | dev_err(dev, "invalid firmware\n"); | |
9ebfbd45 | 1188 | goto out; |
d7584ed2 TT |
1189 | } |
1190 | ||
1191 | ret = qe_upload_firmware(firmware); | |
1192 | if (ret) { | |
1193 | dev_err(dev, "could not load firmware\n"); | |
9ebfbd45 | 1194 | goto out; |
d7584ed2 TT |
1195 | } |
1196 | ||
1197 | firmware_loaded = 1; | |
9ebfbd45 JB |
1198 | out: |
1199 | release_firmware(fw); | |
d7584ed2 TT |
1200 | } |
1201 | ||
793218df | 1202 | static int ucc_uart_probe(struct platform_device *ofdev) |
d7584ed2 | 1203 | { |
61c7a080 | 1204 | struct device_node *np = ofdev->dev.of_node; |
d7584ed2 TT |
1205 | const unsigned int *iprop; /* Integer OF properties */ |
1206 | const char *sprop; /* String OF properties */ | |
1207 | struct uart_qe_port *qe_port = NULL; | |
1208 | struct resource res; | |
1209 | int ret; | |
1210 | ||
1211 | /* | |
1212 | * Determine if we need Soft-UART mode | |
1213 | */ | |
1214 | if (of_find_property(np, "soft-uart", NULL)) { | |
1215 | dev_dbg(&ofdev->dev, "using Soft-UART mode\n"); | |
1216 | soft_uart = 1; | |
1217 | } | |
1218 | ||
1219 | /* | |
1220 | * If we are using Soft-UART, determine if we need to upload the | |
1221 | * firmware, too. | |
1222 | */ | |
1223 | if (soft_uart) { | |
1224 | struct qe_firmware_info *qe_fw_info; | |
1225 | ||
1226 | qe_fw_info = qe_get_firmware_info(); | |
1227 | ||
1228 | /* Check if the firmware has been uploaded. */ | |
1229 | if (qe_fw_info && strstr(qe_fw_info->id, "Soft-UART")) { | |
1230 | firmware_loaded = 1; | |
1231 | } else { | |
1232 | char filename[32]; | |
1233 | unsigned int soc; | |
1234 | unsigned int rev_h; | |
1235 | unsigned int rev_l; | |
1236 | ||
1237 | soc = soc_info(&rev_h, &rev_l); | |
1238 | if (!soc) { | |
1239 | dev_err(&ofdev->dev, "unknown CPU model\n"); | |
1240 | return -ENXIO; | |
1241 | } | |
1242 | sprintf(filename, "fsl_qe_ucode_uart_%u_%u%u.bin", | |
1243 | soc, rev_h, rev_l); | |
1244 | ||
1245 | dev_info(&ofdev->dev, "waiting for firmware %s\n", | |
1246 | filename); | |
1247 | ||
1248 | /* | |
1249 | * We call request_firmware_nowait instead of | |
1250 | * request_firmware so that the driver can load and | |
1251 | * initialize the ports without holding up the rest of | |
1252 | * the kernel. If hotplug support is enabled in the | |
1253 | * kernel, then we use it. | |
1254 | */ | |
1255 | ret = request_firmware_nowait(THIS_MODULE, | |
1256 | FW_ACTION_HOTPLUG, filename, &ofdev->dev, | |
9ebfbd45 | 1257 | GFP_KERNEL, &ofdev->dev, uart_firmware_cont); |
d7584ed2 TT |
1258 | if (ret) { |
1259 | dev_err(&ofdev->dev, | |
1260 | "could not load firmware %s\n", | |
1261 | filename); | |
1262 | return ret; | |
1263 | } | |
1264 | } | |
1265 | } | |
1266 | ||
1267 | qe_port = kzalloc(sizeof(struct uart_qe_port), GFP_KERNEL); | |
1268 | if (!qe_port) { | |
1269 | dev_err(&ofdev->dev, "can't allocate QE port structure\n"); | |
1270 | return -ENOMEM; | |
1271 | } | |
1272 | ||
1273 | /* Search for IRQ and mapbase */ | |
1274 | ret = of_address_to_resource(np, 0, &res); | |
1275 | if (ret) { | |
1276 | dev_err(&ofdev->dev, "missing 'reg' property in device tree\n"); | |
48a10cdf | 1277 | goto out_free; |
d7584ed2 TT |
1278 | } |
1279 | if (!res.start) { | |
1280 | dev_err(&ofdev->dev, "invalid 'reg' property in device tree\n"); | |
48a10cdf JL |
1281 | ret = -EINVAL; |
1282 | goto out_free; | |
d7584ed2 TT |
1283 | } |
1284 | qe_port->port.mapbase = res.start; | |
1285 | ||
1286 | /* Get the UCC number (device ID) */ | |
1287 | /* UCCs are numbered 1-7 */ | |
56626f33 AV |
1288 | iprop = of_get_property(np, "cell-index", NULL); |
1289 | if (!iprop) { | |
1290 | iprop = of_get_property(np, "device-id", NULL); | |
1291 | if (!iprop) { | |
1292 | dev_err(&ofdev->dev, "UCC is unspecified in " | |
1293 | "device tree\n"); | |
48a10cdf JL |
1294 | ret = -EINVAL; |
1295 | goto out_free; | |
56626f33 AV |
1296 | } |
1297 | } | |
1298 | ||
1299 | if ((*iprop < 1) || (*iprop > UCC_MAX_NUM)) { | |
1300 | dev_err(&ofdev->dev, "no support for UCC%u\n", *iprop); | |
48a10cdf JL |
1301 | ret = -ENODEV; |
1302 | goto out_free; | |
d7584ed2 TT |
1303 | } |
1304 | qe_port->ucc_num = *iprop - 1; | |
1305 | ||
1306 | /* | |
1307 | * In the future, we should not require the BRG to be specified in the | |
1308 | * device tree. If no clock-source is specified, then just pick a BRG | |
1309 | * to use. This requires a new QE library function that manages BRG | |
1310 | * assignments. | |
1311 | */ | |
1312 | ||
1313 | sprop = of_get_property(np, "rx-clock-name", NULL); | |
1314 | if (!sprop) { | |
1315 | dev_err(&ofdev->dev, "missing rx-clock-name in device tree\n"); | |
48a10cdf JL |
1316 | ret = -ENODEV; |
1317 | goto out_free; | |
d7584ed2 TT |
1318 | } |
1319 | ||
1320 | qe_port->us_info.rx_clock = qe_clock_source(sprop); | |
1321 | if ((qe_port->us_info.rx_clock < QE_BRG1) || | |
1322 | (qe_port->us_info.rx_clock > QE_BRG16)) { | |
1323 | dev_err(&ofdev->dev, "rx-clock-name must be a BRG for UART\n"); | |
48a10cdf JL |
1324 | ret = -ENODEV; |
1325 | goto out_free; | |
d7584ed2 TT |
1326 | } |
1327 | ||
1328 | #ifdef LOOPBACK | |
1329 | /* In internal loopback mode, TX and RX must use the same clock */ | |
1330 | qe_port->us_info.tx_clock = qe_port->us_info.rx_clock; | |
1331 | #else | |
1332 | sprop = of_get_property(np, "tx-clock-name", NULL); | |
1333 | if (!sprop) { | |
1334 | dev_err(&ofdev->dev, "missing tx-clock-name in device tree\n"); | |
48a10cdf JL |
1335 | ret = -ENODEV; |
1336 | goto out_free; | |
d7584ed2 TT |
1337 | } |
1338 | qe_port->us_info.tx_clock = qe_clock_source(sprop); | |
1339 | #endif | |
1340 | if ((qe_port->us_info.tx_clock < QE_BRG1) || | |
1341 | (qe_port->us_info.tx_clock > QE_BRG16)) { | |
1342 | dev_err(&ofdev->dev, "tx-clock-name must be a BRG for UART\n"); | |
48a10cdf JL |
1343 | ret = -ENODEV; |
1344 | goto out_free; | |
d7584ed2 TT |
1345 | } |
1346 | ||
1347 | /* Get the port number, numbered 0-3 */ | |
1348 | iprop = of_get_property(np, "port-number", NULL); | |
1349 | if (!iprop) { | |
1350 | dev_err(&ofdev->dev, "missing port-number in device tree\n"); | |
48a10cdf JL |
1351 | ret = -EINVAL; |
1352 | goto out_free; | |
d7584ed2 TT |
1353 | } |
1354 | qe_port->port.line = *iprop; | |
1355 | if (qe_port->port.line >= UCC_MAX_UART) { | |
1356 | dev_err(&ofdev->dev, "port-number must be 0-%u\n", | |
1357 | UCC_MAX_UART - 1); | |
48a10cdf JL |
1358 | ret = -EINVAL; |
1359 | goto out_free; | |
d7584ed2 TT |
1360 | } |
1361 | ||
1362 | qe_port->port.irq = irq_of_parse_and_map(np, 0); | |
d4e33fac | 1363 | if (qe_port->port.irq == 0) { |
d7584ed2 TT |
1364 | dev_err(&ofdev->dev, "could not map IRQ for UCC%u\n", |
1365 | qe_port->ucc_num + 1); | |
48a10cdf JL |
1366 | ret = -EINVAL; |
1367 | goto out_free; | |
d7584ed2 TT |
1368 | } |
1369 | ||
1370 | /* | |
1371 | * Newer device trees have an "fsl,qe" compatible property for the QE | |
1372 | * node, but we still need to support older device trees. | |
1373 | */ | |
1374 | np = of_find_compatible_node(NULL, NULL, "fsl,qe"); | |
1375 | if (!np) { | |
1376 | np = of_find_node_by_type(NULL, "qe"); | |
1377 | if (!np) { | |
1378 | dev_err(&ofdev->dev, "could not find 'qe' node\n"); | |
48a10cdf JL |
1379 | ret = -EINVAL; |
1380 | goto out_free; | |
d7584ed2 TT |
1381 | } |
1382 | } | |
1383 | ||
1384 | iprop = of_get_property(np, "brg-frequency", NULL); | |
1385 | if (!iprop) { | |
1386 | dev_err(&ofdev->dev, | |
1387 | "missing brg-frequency in device tree\n"); | |
48a10cdf JL |
1388 | ret = -EINVAL; |
1389 | goto out_np; | |
d7584ed2 TT |
1390 | } |
1391 | ||
1392 | if (*iprop) | |
1393 | qe_port->port.uartclk = *iprop; | |
1394 | else { | |
1395 | /* | |
1396 | * Older versions of U-Boot do not initialize the brg-frequency | |
1397 | * property, so in this case we assume the BRG frequency is | |
1398 | * half the QE bus frequency. | |
1399 | */ | |
1400 | iprop = of_get_property(np, "bus-frequency", NULL); | |
1401 | if (!iprop) { | |
1402 | dev_err(&ofdev->dev, | |
1403 | "missing QE bus-frequency in device tree\n"); | |
48a10cdf JL |
1404 | ret = -EINVAL; |
1405 | goto out_np; | |
d7584ed2 TT |
1406 | } |
1407 | if (*iprop) | |
1408 | qe_port->port.uartclk = *iprop / 2; | |
1409 | else { | |
1410 | dev_err(&ofdev->dev, | |
1411 | "invalid QE bus-frequency in device tree\n"); | |
48a10cdf JL |
1412 | ret = -EINVAL; |
1413 | goto out_np; | |
d7584ed2 TT |
1414 | } |
1415 | } | |
1416 | ||
1417 | spin_lock_init(&qe_port->port.lock); | |
1418 | qe_port->np = np; | |
1419 | qe_port->port.dev = &ofdev->dev; | |
1420 | qe_port->port.ops = &qe_uart_pops; | |
1421 | qe_port->port.iotype = UPIO_MEM; | |
1422 | ||
1423 | qe_port->tx_nrfifos = TX_NUM_FIFO; | |
1424 | qe_port->tx_fifosize = TX_BUF_SIZE; | |
1425 | qe_port->rx_nrfifos = RX_NUM_FIFO; | |
1426 | qe_port->rx_fifosize = RX_BUF_SIZE; | |
1427 | ||
1428 | qe_port->wait_closing = UCC_WAIT_CLOSING; | |
1429 | qe_port->port.fifosize = 512; | |
1430 | qe_port->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP; | |
1431 | ||
1432 | qe_port->us_info.ucc_num = qe_port->ucc_num; | |
1433 | qe_port->us_info.regs = (phys_addr_t) res.start; | |
1434 | qe_port->us_info.irq = qe_port->port.irq; | |
1435 | ||
1436 | qe_port->us_info.rx_bd_ring_len = qe_port->rx_nrfifos; | |
1437 | qe_port->us_info.tx_bd_ring_len = qe_port->tx_nrfifos; | |
1438 | ||
1439 | /* Make sure ucc_slow_init() initializes both TX and RX */ | |
1440 | qe_port->us_info.init_tx = 1; | |
1441 | qe_port->us_info.init_rx = 1; | |
1442 | ||
1443 | /* Add the port to the uart sub-system. This will cause | |
1444 | * qe_uart_config_port() to be called, so the us_info structure must | |
1445 | * be initialized. | |
1446 | */ | |
1447 | ret = uart_add_one_port(&ucc_uart_driver, &qe_port->port); | |
1448 | if (ret) { | |
1449 | dev_err(&ofdev->dev, "could not add /dev/ttyQE%u\n", | |
1450 | qe_port->port.line); | |
48a10cdf | 1451 | goto out_np; |
d7584ed2 TT |
1452 | } |
1453 | ||
1454 | dev_set_drvdata(&ofdev->dev, qe_port); | |
1455 | ||
1456 | dev_info(&ofdev->dev, "UCC%u assigned to /dev/ttyQE%u\n", | |
1457 | qe_port->ucc_num + 1, qe_port->port.line); | |
1458 | ||
1459 | /* Display the mknod command for this device */ | |
1460 | dev_dbg(&ofdev->dev, "mknod command is 'mknod /dev/ttyQE%u c %u %u'\n", | |
1461 | qe_port->port.line, SERIAL_QE_MAJOR, | |
1462 | SERIAL_QE_MINOR + qe_port->port.line); | |
1463 | ||
1464 | return 0; | |
48a10cdf JL |
1465 | out_np: |
1466 | of_node_put(np); | |
1467 | out_free: | |
1468 | kfree(qe_port); | |
1469 | return ret; | |
d7584ed2 TT |
1470 | } |
1471 | ||
2dc11581 | 1472 | static int ucc_uart_remove(struct platform_device *ofdev) |
d7584ed2 TT |
1473 | { |
1474 | struct uart_qe_port *qe_port = dev_get_drvdata(&ofdev->dev); | |
1475 | ||
1476 | dev_info(&ofdev->dev, "removing /dev/ttyQE%u\n", qe_port->port.line); | |
1477 | ||
1478 | uart_remove_one_port(&ucc_uart_driver, &qe_port->port); | |
1479 | ||
1480 | dev_set_drvdata(&ofdev->dev, NULL); | |
1481 | kfree(qe_port); | |
1482 | ||
1483 | return 0; | |
1484 | } | |
1485 | ||
1486 | static struct of_device_id ucc_uart_match[] = { | |
1487 | { | |
1488 | .type = "serial", | |
1489 | .compatible = "ucc_uart", | |
1490 | }, | |
1491 | {}, | |
1492 | }; | |
1493 | MODULE_DEVICE_TABLE(of, ucc_uart_match); | |
1494 | ||
793218df | 1495 | static struct platform_driver ucc_uart_of_driver = { |
4018294b GL |
1496 | .driver = { |
1497 | .name = "ucc_uart", | |
1498 | .owner = THIS_MODULE, | |
1499 | .of_match_table = ucc_uart_match, | |
1500 | }, | |
d7584ed2 TT |
1501 | .probe = ucc_uart_probe, |
1502 | .remove = ucc_uart_remove, | |
1503 | }; | |
1504 | ||
1505 | static int __init ucc_uart_init(void) | |
1506 | { | |
1507 | int ret; | |
1508 | ||
1509 | printk(KERN_INFO "Freescale QUICC Engine UART device driver\n"); | |
1510 | #ifdef LOOPBACK | |
1511 | printk(KERN_INFO "ucc-uart: Using loopback mode\n"); | |
1512 | #endif | |
1513 | ||
1514 | ret = uart_register_driver(&ucc_uart_driver); | |
1515 | if (ret) { | |
1516 | printk(KERN_ERR "ucc-uart: could not register UART driver\n"); | |
1517 | return ret; | |
1518 | } | |
1519 | ||
793218df | 1520 | ret = platform_driver_register(&ucc_uart_of_driver); |
d7584ed2 TT |
1521 | if (ret) |
1522 | printk(KERN_ERR | |
1523 | "ucc-uart: could not register platform driver\n"); | |
1524 | ||
1525 | return ret; | |
1526 | } | |
1527 | ||
1528 | static void __exit ucc_uart_exit(void) | |
1529 | { | |
1530 | printk(KERN_INFO | |
1531 | "Freescale QUICC Engine UART device driver unloading\n"); | |
1532 | ||
793218df | 1533 | platform_driver_unregister(&ucc_uart_of_driver); |
d7584ed2 TT |
1534 | uart_unregister_driver(&ucc_uart_driver); |
1535 | } | |
1536 | ||
1537 | module_init(ucc_uart_init); | |
1538 | module_exit(ucc_uart_exit); | |
1539 | ||
1540 | MODULE_DESCRIPTION("Freescale QUICC Engine (QE) UART"); | |
1541 | MODULE_AUTHOR("Timur Tabi <timur@freescale.com>"); | |
1542 | MODULE_LICENSE("GPL v2"); | |
1543 | MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_QE_MAJOR); | |
1544 |