Commit | Line | Data |
---|---|---|
56f5b1cf PZ |
1 | /* |
2 | * core.h - DesignWare HS OTG Controller common declarations | |
3 | * | |
4 | * Copyright (C) 2004-2013 Synopsys, Inc. | |
5 | * | |
6 | * Redistribution and use in source and binary forms, with or without | |
7 | * modification, are permitted provided that the following conditions | |
8 | * are met: | |
9 | * 1. Redistributions of source code must retain the above copyright | |
10 | * notice, this list of conditions, and the following disclaimer, | |
11 | * without modification. | |
12 | * 2. Redistributions in binary form must reproduce the above copyright | |
13 | * notice, this list of conditions and the following disclaimer in the | |
14 | * documentation and/or other materials provided with the distribution. | |
15 | * 3. The names of the above-listed copyright holders may not be used | |
16 | * to endorse or promote products derived from this software without | |
17 | * specific prior written permission. | |
18 | * | |
19 | * ALTERNATIVELY, this software may be distributed under the terms of the | |
20 | * GNU General Public License ("GPL") as published by the Free Software | |
21 | * Foundation; either version 2 of the License, or (at your option) any | |
22 | * later version. | |
23 | * | |
24 | * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS | |
25 | * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, | |
26 | * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR | |
27 | * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR | |
28 | * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, | |
29 | * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, | |
30 | * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR | |
31 | * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF | |
32 | * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING | |
33 | * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS | |
34 | * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
35 | */ | |
36 | ||
37 | #ifndef __DWC2_CORE_H__ | |
38 | #define __DWC2_CORE_H__ | |
39 | ||
f7c0b143 DN |
40 | #include <linux/phy/phy.h> |
41 | #include <linux/regulator/consumer.h> | |
42 | #include <linux/usb/gadget.h> | |
43 | #include <linux/usb/otg.h> | |
56f5b1cf PZ |
44 | #include <linux/usb/phy.h> |
45 | #include "hw.h" | |
46 | ||
47 | #ifdef DWC2_LOG_WRITES | |
48 | static inline void do_write(u32 value, void *addr) | |
49 | { | |
50 | writel(value, addr); | |
51 | pr_info("INFO:: wrote %08x to %p\n", value, addr); | |
52 | } | |
53 | ||
54 | #undef writel | |
55 | #define writel(v, a) do_write(v, a) | |
56 | #endif | |
57 | ||
58 | /* Maximum number of Endpoints/HostChannels */ | |
59 | #define MAX_EPS_CHANNELS 16 | |
60 | ||
f7c0b143 DN |
61 | /* s3c-hsotg declarations */ |
62 | static const char * const s3c_hsotg_supply_names[] = { | |
63 | "vusb_d", /* digital USB supply, 1.2V */ | |
64 | "vusb_a", /* analog USB supply, 1.1V */ | |
65 | }; | |
66 | ||
67 | /* | |
68 | * EP0_MPS_LIMIT | |
69 | * | |
70 | * Unfortunately there seems to be a limit of the amount of data that can | |
71 | * be transferred by IN transactions on EP0. This is either 127 bytes or 3 | |
72 | * packets (which practically means 1 packet and 63 bytes of data) when the | |
73 | * MPS is set to 64. | |
74 | * | |
75 | * This means if we are wanting to move >127 bytes of data, we need to | |
76 | * split the transactions up, but just doing one packet at a time does | |
77 | * not work (this may be an implicit DATA0 PID on first packet of the | |
78 | * transaction) and doing 2 packets is outside the controller's limits. | |
79 | * | |
80 | * If we try to lower the MPS size for EP0, then no transfers work properly | |
81 | * for EP0, and the system will fail basic enumeration. As no cause for this | |
82 | * has currently been found, we cannot support any large IN transfers for | |
83 | * EP0. | |
84 | */ | |
85 | #define EP0_MPS_LIMIT 64 | |
86 | ||
87 | struct s3c_hsotg; | |
88 | struct s3c_hsotg_req; | |
89 | ||
90 | /** | |
91 | * struct s3c_hsotg_ep - driver endpoint definition. | |
92 | * @ep: The gadget layer representation of the endpoint. | |
93 | * @name: The driver generated name for the endpoint. | |
94 | * @queue: Queue of requests for this endpoint. | |
95 | * @parent: Reference back to the parent device structure. | |
96 | * @req: The current request that the endpoint is processing. This is | |
97 | * used to indicate an request has been loaded onto the endpoint | |
98 | * and has yet to be completed (maybe due to data move, or simply | |
99 | * awaiting an ack from the core all the data has been completed). | |
100 | * @debugfs: File entry for debugfs file for this endpoint. | |
101 | * @lock: State lock to protect contents of endpoint. | |
102 | * @dir_in: Set to true if this endpoint is of the IN direction, which | |
103 | * means that it is sending data to the Host. | |
104 | * @index: The index for the endpoint registers. | |
105 | * @mc: Multi Count - number of transactions per microframe | |
106 | * @interval - Interval for periodic endpoints | |
107 | * @name: The name array passed to the USB core. | |
108 | * @halted: Set if the endpoint has been halted. | |
109 | * @periodic: Set if this is a periodic ep, such as Interrupt | |
110 | * @isochronous: Set if this is a isochronous ep | |
111 | * @sent_zlp: Set if we've sent a zero-length packet. | |
112 | * @total_data: The total number of data bytes done. | |
113 | * @fifo_size: The size of the FIFO (for periodic IN endpoints) | |
114 | * @fifo_load: The amount of data loaded into the FIFO (periodic IN) | |
115 | * @last_load: The offset of data for the last start of request. | |
116 | * @size_loaded: The last loaded size for DxEPTSIZE for periodic IN | |
117 | * | |
118 | * This is the driver's state for each registered enpoint, allowing it | |
119 | * to keep track of transactions that need doing. Each endpoint has a | |
120 | * lock to protect the state, to try and avoid using an overall lock | |
121 | * for the host controller as much as possible. | |
122 | * | |
123 | * For periodic IN endpoints, we have fifo_size and fifo_load to try | |
124 | * and keep track of the amount of data in the periodic FIFO for each | |
125 | * of these as we don't have a status register that tells us how much | |
126 | * is in each of them. (note, this may actually be useless information | |
127 | * as in shared-fifo mode periodic in acts like a single-frame packet | |
128 | * buffer than a fifo) | |
129 | */ | |
130 | struct s3c_hsotg_ep { | |
131 | struct usb_ep ep; | |
132 | struct list_head queue; | |
133 | struct s3c_hsotg *parent; | |
134 | struct s3c_hsotg_req *req; | |
135 | struct dentry *debugfs; | |
136 | ||
137 | unsigned long total_data; | |
138 | unsigned int size_loaded; | |
139 | unsigned int last_load; | |
140 | unsigned int fifo_load; | |
141 | unsigned short fifo_size; | |
b203d0a2 | 142 | unsigned short fifo_index; |
f7c0b143 DN |
143 | |
144 | unsigned char dir_in; | |
145 | unsigned char index; | |
146 | unsigned char mc; | |
147 | unsigned char interval; | |
148 | ||
149 | unsigned int halted:1; | |
150 | unsigned int periodic:1; | |
151 | unsigned int isochronous:1; | |
152 | unsigned int sent_zlp:1; | |
153 | ||
154 | char name[10]; | |
155 | }; | |
156 | ||
157 | /** | |
158 | * struct s3c_hsotg - driver state. | |
159 | * @dev: The parent device supplied to the probe function | |
160 | * @driver: USB gadget driver | |
161 | * @phy: The otg phy transceiver structure for phy control. | |
162 | * @uphy: The otg phy transceiver structure for old USB phy control. | |
163 | * @plat: The platform specific configuration data. This can be removed once | |
164 | * all SoCs support usb transceiver. | |
165 | * @regs: The memory area mapped for accessing registers. | |
166 | * @irq: The IRQ number we are using | |
167 | * @supplies: Definition of USB power supplies | |
168 | * @phyif: PHY interface width | |
169 | * @dedicated_fifos: Set if the hardware has dedicated IN-EP fifos. | |
170 | * @num_of_eps: Number of available EPs (excluding EP0) | |
171 | * @debug_root: root directrory for debugfs. | |
172 | * @debug_file: main status file for debugfs. | |
173 | * @debug_fifo: FIFO status file for debugfs. | |
174 | * @ep0_reply: Request used for ep0 reply. | |
175 | * @ep0_buff: Buffer for EP0 reply data, if needed. | |
176 | * @ctrl_buff: Buffer for EP0 control requests. | |
177 | * @ctrl_req: Request for EP0 control packets. | |
178 | * @setup: NAK management for EP0 SETUP | |
179 | * @last_rst: Time of last reset | |
180 | * @eps: The endpoints being supplied to the gadget framework | |
181 | */ | |
182 | struct s3c_hsotg { | |
183 | struct device *dev; | |
184 | struct usb_gadget_driver *driver; | |
185 | struct phy *phy; | |
186 | struct usb_phy *uphy; | |
187 | struct s3c_hsotg_plat *plat; | |
188 | ||
189 | spinlock_t lock; | |
190 | ||
191 | void __iomem *regs; | |
192 | int irq; | |
193 | struct clk *clk; | |
194 | ||
195 | struct regulator_bulk_data supplies[ARRAY_SIZE(s3c_hsotg_supply_names)]; | |
196 | ||
197 | u32 phyif; | |
cff9eb75 | 198 | int fifo_mem; |
f7c0b143 DN |
199 | unsigned int dedicated_fifos:1; |
200 | unsigned char num_of_eps; | |
b203d0a2 | 201 | u32 fifo_map; |
f7c0b143 DN |
202 | |
203 | struct dentry *debug_root; | |
204 | struct dentry *debug_file; | |
205 | struct dentry *debug_fifo; | |
206 | ||
207 | struct usb_request *ep0_reply; | |
208 | struct usb_request *ctrl_req; | |
209 | u8 ep0_buff[8]; | |
210 | u8 ctrl_buff[8]; | |
211 | ||
212 | struct usb_gadget gadget; | |
213 | unsigned int setup; | |
214 | unsigned long last_rst; | |
215 | struct s3c_hsotg_ep *eps; | |
216 | }; | |
217 | ||
218 | /** | |
219 | * struct s3c_hsotg_req - data transfer request | |
220 | * @req: The USB gadget request | |
221 | * @queue: The list of requests for the endpoint this is queued for. | |
222 | * @in_progress: Has already had size/packets written to core | |
223 | * @mapped: DMA buffer for this request has been mapped via dma_map_single(). | |
224 | */ | |
225 | struct s3c_hsotg_req { | |
226 | struct usb_request req; | |
227 | struct list_head queue; | |
228 | unsigned char in_progress; | |
229 | unsigned char mapped; | |
230 | }; | |
231 | ||
232 | #define call_gadget(_hs, _entry) \ | |
233 | do { \ | |
234 | if ((_hs)->gadget.speed != USB_SPEED_UNKNOWN && \ | |
235 | (_hs)->driver && (_hs)->driver->_entry) { \ | |
236 | spin_unlock(&_hs->lock); \ | |
237 | (_hs)->driver->_entry(&(_hs)->gadget); \ | |
238 | spin_lock(&_hs->lock); \ | |
239 | } \ | |
240 | } while (0) | |
241 | ||
56f5b1cf PZ |
242 | struct dwc2_hsotg; |
243 | struct dwc2_host_chan; | |
244 | ||
245 | /* Device States */ | |
246 | enum dwc2_lx_state { | |
247 | DWC2_L0, /* On state */ | |
248 | DWC2_L1, /* LPM sleep state */ | |
249 | DWC2_L2, /* USB suspend state */ | |
250 | DWC2_L3, /* Off state */ | |
251 | }; | |
252 | ||
253 | /** | |
254 | * struct dwc2_core_params - Parameters for configuring the core | |
255 | * | |
91121c10 MK |
256 | * @otg_cap: Specifies the OTG capabilities. |
257 | * 0 - HNP and SRP capable | |
56f5b1cf | 258 | * 1 - SRP Only capable |
91121c10 MK |
259 | * 2 - No HNP/SRP capable (always available) |
260 | * Defaults to best available option (0, 1, then 2) | |
725acc86 | 261 | * @otg_ver: OTG version supported |
91121c10 | 262 | * 0 - 1.3 (default) |
725acc86 | 263 | * 1 - 2.0 |
56f5b1cf PZ |
264 | * @dma_enable: Specifies whether to use slave or DMA mode for accessing |
265 | * the data FIFOs. The driver will automatically detect the | |
266 | * value for this parameter if none is specified. | |
91121c10 | 267 | * 0 - Slave (always available) |
56f5b1cf PZ |
268 | * 1 - DMA (default, if available) |
269 | * @dma_desc_enable: When DMA mode is enabled, specifies whether to use | |
270 | * address DMA mode or descriptor DMA mode for accessing | |
271 | * the data FIFOs. The driver will automatically detect the | |
272 | * value for this if none is specified. | |
273 | * 0 - Address DMA | |
274 | * 1 - Descriptor DMA (default, if available) | |
275 | * @speed: Specifies the maximum speed of operation in host and | |
276 | * device mode. The actual speed depends on the speed of | |
277 | * the attached device and the value of phy_type. | |
91121c10 MK |
278 | * 0 - High Speed |
279 | * (default when phy_type is UTMI+ or ULPI) | |
56f5b1cf | 280 | * 1 - Full Speed |
91121c10 | 281 | * (default when phy_type is Full Speed) |
56f5b1cf | 282 | * @enable_dynamic_fifo: 0 - Use coreConsultant-specified FIFO size parameters |
91121c10 | 283 | * 1 - Allow dynamic FIFO sizing (default, if available) |
725acc86 PZ |
284 | * @en_multiple_tx_fifo: Specifies whether dedicated per-endpoint transmit FIFOs |
285 | * are enabled | |
56f5b1cf PZ |
286 | * @host_rx_fifo_size: Number of 4-byte words in the Rx FIFO in host mode when |
287 | * dynamic FIFO sizing is enabled | |
91121c10 MK |
288 | * 16 to 32768 |
289 | * Actual maximum value is autodetected and also | |
290 | * the default. | |
56f5b1cf PZ |
291 | * @host_nperio_tx_fifo_size: Number of 4-byte words in the non-periodic Tx FIFO |
292 | * in host mode when dynamic FIFO sizing is enabled | |
91121c10 MK |
293 | * 16 to 32768 |
294 | * Actual maximum value is autodetected and also | |
295 | * the default. | |
56f5b1cf PZ |
296 | * @host_perio_tx_fifo_size: Number of 4-byte words in the periodic Tx FIFO in |
297 | * host mode when dynamic FIFO sizing is enabled | |
91121c10 MK |
298 | * 16 to 32768 |
299 | * Actual maximum value is autodetected and also | |
300 | * the default. | |
56f5b1cf | 301 | * @max_transfer_size: The maximum transfer size supported, in bytes |
91121c10 MK |
302 | * 2047 to 65,535 |
303 | * Actual maximum value is autodetected and also | |
304 | * the default. | |
56f5b1cf | 305 | * @max_packet_count: The maximum number of packets in a transfer |
91121c10 MK |
306 | * 15 to 511 |
307 | * Actual maximum value is autodetected and also | |
308 | * the default. | |
56f5b1cf | 309 | * @host_channels: The number of host channel registers to use |
91121c10 MK |
310 | * 1 to 16 |
311 | * Actual maximum value is autodetected and also | |
312 | * the default. | |
56f5b1cf PZ |
313 | * @phy_type: Specifies the type of PHY interface to use. By default, |
314 | * the driver will automatically detect the phy_type. | |
91121c10 MK |
315 | * 0 - Full Speed Phy |
316 | * 1 - UTMI+ Phy | |
317 | * 2 - ULPI Phy | |
318 | * Defaults to best available option (2, 1, then 0) | |
56f5b1cf PZ |
319 | * @phy_utmi_width: Specifies the UTMI+ Data Width (in bits). This parameter |
320 | * is applicable for a phy_type of UTMI+ or ULPI. (For a | |
321 | * ULPI phy_type, this parameter indicates the data width | |
322 | * between the MAC and the ULPI Wrapper.) Also, this | |
323 | * parameter is applicable only if the OTG_HSPHY_WIDTH cC | |
324 | * parameter was set to "8 and 16 bits", meaning that the | |
325 | * core has been configured to work at either data path | |
326 | * width. | |
91121c10 | 327 | * 8 or 16 (default 16 if available) |
56f5b1cf PZ |
328 | * @phy_ulpi_ddr: Specifies whether the ULPI operates at double or single |
329 | * data rate. This parameter is only applicable if phy_type | |
330 | * is ULPI. | |
331 | * 0 - single data rate ULPI interface with 8 bit wide | |
332 | * data bus (default) | |
333 | * 1 - double data rate ULPI interface with 4 bit wide | |
334 | * data bus | |
335 | * @phy_ulpi_ext_vbus: For a ULPI phy, specifies whether to use the internal or | |
336 | * external supply to drive the VBus | |
91121c10 MK |
337 | * 0 - Internal supply (default) |
338 | * 1 - External supply | |
56f5b1cf PZ |
339 | * @i2c_enable: Specifies whether to use the I2Cinterface for a full |
340 | * speed PHY. This parameter is only applicable if phy_type | |
341 | * is FS. | |
342 | * 0 - No (default) | |
343 | * 1 - Yes | |
91121c10 MK |
344 | * @ulpi_fs_ls: Make ULPI phy operate in FS/LS mode only |
345 | * 0 - No (default) | |
346 | * 1 - Yes | |
725acc86 PZ |
347 | * @host_support_fs_ls_low_power: Specifies whether low power mode is supported |
348 | * when attached to a Full Speed or Low Speed device in | |
349 | * host mode. | |
350 | * 0 - Don't support low power mode (default) | |
351 | * 1 - Support low power mode | |
352 | * @host_ls_low_power_phy_clk: Specifies the PHY clock rate in low power mode | |
91121c10 MK |
353 | * when connected to a Low Speed device in host |
354 | * mode. This parameter is applicable only if | |
355 | * host_support_fs_ls_low_power is enabled. | |
725acc86 | 356 | * 0 - 48 MHz |
91121c10 | 357 | * (default when phy_type is UTMI+ or ULPI) |
725acc86 | 358 | * 1 - 6 MHz |
91121c10 MK |
359 | * (default when phy_type is Full Speed) |
360 | * @ts_dline: Enable Term Select Dline pulsing | |
361 | * 0 - No (default) | |
362 | * 1 - Yes | |
363 | * @reload_ctl: Allow dynamic reloading of HFIR register during runtime | |
364 | * 0 - No (default for core < 2.92a) | |
365 | * 1 - Yes (default for core >= 2.92a) | |
4d3190e1 PZ |
366 | * @ahbcfg: This field allows the default value of the GAHBCFG |
367 | * register to be overridden | |
91121c10 MK |
368 | * -1 - GAHBCFG value will be set to 0x06 |
369 | * (INCR4, default) | |
4d3190e1 PZ |
370 | * all others - GAHBCFG value will be overridden with |
371 | * this value | |
91121c10 MK |
372 | * Not all bits can be controlled like this, the |
373 | * bits defined by GAHBCFG_CTRL_MASK are controlled | |
374 | * by the driver and are ignored in this | |
375 | * configuration value. | |
20f2eb9c | 376 | * @uframe_sched: True to enable the microframe scheduler |
56f5b1cf PZ |
377 | * |
378 | * The following parameters may be specified when starting the module. These | |
91121c10 MK |
379 | * parameters define how the DWC_otg controller should be configured. A |
380 | * value of -1 (or any other out of range value) for any parameter means | |
381 | * to read the value from hardware (if possible) or use the builtin | |
382 | * default described above. | |
56f5b1cf PZ |
383 | */ |
384 | struct dwc2_core_params { | |
8284f93b MK |
385 | /* |
386 | * Don't add any non-int members here, this will break | |
387 | * dwc2_set_all_params! | |
388 | */ | |
56f5b1cf PZ |
389 | int otg_cap; |
390 | int otg_ver; | |
391 | int dma_enable; | |
392 | int dma_desc_enable; | |
393 | int speed; | |
394 | int enable_dynamic_fifo; | |
395 | int en_multiple_tx_fifo; | |
396 | int host_rx_fifo_size; | |
397 | int host_nperio_tx_fifo_size; | |
398 | int host_perio_tx_fifo_size; | |
399 | int max_transfer_size; | |
400 | int max_packet_count; | |
401 | int host_channels; | |
402 | int phy_type; | |
403 | int phy_utmi_width; | |
404 | int phy_ulpi_ddr; | |
405 | int phy_ulpi_ext_vbus; | |
406 | int i2c_enable; | |
407 | int ulpi_fs_ls; | |
408 | int host_support_fs_ls_low_power; | |
409 | int host_ls_low_power_phy_clk; | |
410 | int ts_dline; | |
411 | int reload_ctl; | |
4d3190e1 | 412 | int ahbcfg; |
20f2eb9c | 413 | int uframe_sched; |
56f5b1cf PZ |
414 | }; |
415 | ||
9badec2f MK |
416 | /** |
417 | * struct dwc2_hw_params - Autodetected parameters. | |
418 | * | |
419 | * These parameters are the various parameters read from hardware | |
420 | * registers during initialization. They typically contain the best | |
421 | * supported or maximum value that can be configured in the | |
422 | * corresponding dwc2_core_params value. | |
423 | * | |
424 | * The values that are not in dwc2_core_params are documented below. | |
425 | * | |
426 | * @op_mode Mode of Operation | |
427 | * 0 - HNP- and SRP-Capable OTG (Host & Device) | |
428 | * 1 - SRP-Capable OTG (Host & Device) | |
429 | * 2 - Non-HNP and Non-SRP Capable OTG (Host & Device) | |
430 | * 3 - SRP-Capable Device | |
431 | * 4 - Non-OTG Device | |
432 | * 5 - SRP-Capable Host | |
433 | * 6 - Non-OTG Host | |
434 | * @arch Architecture | |
435 | * 0 - Slave only | |
436 | * 1 - External DMA | |
437 | * 2 - Internal DMA | |
438 | * @power_optimized Are power optimizations enabled? | |
439 | * @num_dev_ep Number of device endpoints available | |
440 | * @num_dev_perio_in_ep Number of device periodic IN endpoints | |
441 | * avaialable | |
442 | * @dev_token_q_depth Device Mode IN Token Sequence Learning Queue | |
443 | * Depth | |
444 | * 0 to 30 | |
445 | * @host_perio_tx_q_depth | |
446 | * Host Mode Periodic Request Queue Depth | |
447 | * 2, 4 or 8 | |
448 | * @nperio_tx_q_depth | |
449 | * Non-Periodic Request Queue Depth | |
450 | * 2, 4 or 8 | |
451 | * @hs_phy_type High-speed PHY interface type | |
452 | * 0 - High-speed interface not supported | |
453 | * 1 - UTMI+ | |
454 | * 2 - ULPI | |
455 | * 3 - UTMI+ and ULPI | |
456 | * @fs_phy_type Full-speed PHY interface type | |
457 | * 0 - Full speed interface not supported | |
458 | * 1 - Dedicated full speed interface | |
459 | * 2 - FS pins shared with UTMI+ pins | |
460 | * 3 - FS pins shared with ULPI pins | |
461 | * @total_fifo_size: Total internal RAM for FIFOs (bytes) | |
de4a1931 MK |
462 | * @utmi_phy_data_width UTMI+ PHY data width |
463 | * 0 - 8 bits | |
464 | * 1 - 16 bits | |
465 | * 2 - 8 or 16 bits | |
9badec2f MK |
466 | * @snpsid: Value from SNPSID register |
467 | */ | |
468 | struct dwc2_hw_params { | |
469 | unsigned op_mode:3; | |
470 | unsigned arch:2; | |
471 | unsigned dma_desc_enable:1; | |
472 | unsigned enable_dynamic_fifo:1; | |
473 | unsigned en_multiple_tx_fifo:1; | |
474 | unsigned host_rx_fifo_size:16; | |
475 | unsigned host_nperio_tx_fifo_size:16; | |
476 | unsigned host_perio_tx_fifo_size:16; | |
477 | unsigned nperio_tx_q_depth:3; | |
478 | unsigned host_perio_tx_q_depth:3; | |
479 | unsigned dev_token_q_depth:5; | |
480 | unsigned max_transfer_size:26; | |
481 | unsigned max_packet_count:11; | |
2d115547 | 482 | unsigned host_channels:5; |
9badec2f MK |
483 | unsigned hs_phy_type:2; |
484 | unsigned fs_phy_type:2; | |
485 | unsigned i2c_enable:1; | |
486 | unsigned num_dev_ep:4; | |
487 | unsigned num_dev_perio_in_ep:4; | |
488 | unsigned total_fifo_size:16; | |
489 | unsigned power_optimized:1; | |
de4a1931 | 490 | unsigned utmi_phy_data_width:2; |
9badec2f MK |
491 | u32 snpsid; |
492 | }; | |
493 | ||
56f5b1cf PZ |
494 | /** |
495 | * struct dwc2_hsotg - Holds the state of the driver, including the non-periodic | |
496 | * and periodic schedules | |
497 | * | |
498 | * @dev: The struct device pointer | |
499 | * @regs: Pointer to controller regs | |
500 | * @core_params: Parameters that define how the core should be configured | |
9badec2f MK |
501 | * @hw_params: Parameters that were autodetected from the |
502 | * hardware registers | |
56f5b1cf PZ |
503 | * @op_state: The operational State, during transitions (a_host=> |
504 | * a_peripheral and b_device=>b_host) this may not match | |
505 | * the core, but allows the software to determine | |
506 | * transitions | |
c0155b9d KY |
507 | * @dr_mode: Requested mode of operation, one of following: |
508 | * - USB_DR_MODE_PERIPHERAL | |
509 | * - USB_DR_MODE_HOST | |
510 | * - USB_DR_MODE_OTG | |
56f5b1cf PZ |
511 | * @queuing_high_bandwidth: True if multiple packets of a high-bandwidth |
512 | * transfer are in process of being queued | |
513 | * @srp_success: Stores status of SRP request in the case of a FS PHY | |
514 | * with an I2C interface | |
515 | * @wq_otg: Workqueue object used for handling of some interrupts | |
516 | * @wf_otg: Work object for handling Connector ID Status Change | |
517 | * interrupt | |
518 | * @wkp_timer: Timer object for handling Wakeup Detected interrupt | |
519 | * @lx_state: Lx state of connected device | |
520 | * @flags: Flags for handling root port state changes | |
521 | * @non_periodic_sched_inactive: Inactive QHs in the non-periodic schedule. | |
522 | * Transfers associated with these QHs are not currently | |
523 | * assigned to a host channel. | |
524 | * @non_periodic_sched_active: Active QHs in the non-periodic schedule. | |
525 | * Transfers associated with these QHs are currently | |
526 | * assigned to a host channel. | |
527 | * @non_periodic_qh_ptr: Pointer to next QH to process in the active | |
528 | * non-periodic schedule | |
529 | * @periodic_sched_inactive: Inactive QHs in the periodic schedule. This is a | |
530 | * list of QHs for periodic transfers that are _not_ | |
531 | * scheduled for the next frame. Each QH in the list has an | |
532 | * interval counter that determines when it needs to be | |
533 | * scheduled for execution. This scheduling mechanism | |
534 | * allows only a simple calculation for periodic bandwidth | |
535 | * used (i.e. must assume that all periodic transfers may | |
536 | * need to execute in the same frame). However, it greatly | |
537 | * simplifies scheduling and should be sufficient for the | |
538 | * vast majority of OTG hosts, which need to connect to a | |
539 | * small number of peripherals at one time. Items move from | |
540 | * this list to periodic_sched_ready when the QH interval | |
541 | * counter is 0 at SOF. | |
542 | * @periodic_sched_ready: List of periodic QHs that are ready for execution in | |
543 | * the next frame, but have not yet been assigned to host | |
544 | * channels. Items move from this list to | |
545 | * periodic_sched_assigned as host channels become | |
546 | * available during the current frame. | |
547 | * @periodic_sched_assigned: List of periodic QHs to be executed in the next | |
548 | * frame that are assigned to host channels. Items move | |
549 | * from this list to periodic_sched_queued as the | |
550 | * transactions for the QH are queued to the DWC_otg | |
551 | * controller. | |
552 | * @periodic_sched_queued: List of periodic QHs that have been queued for | |
553 | * execution. Items move from this list to either | |
554 | * periodic_sched_inactive or periodic_sched_ready when the | |
555 | * channel associated with the transfer is released. If the | |
556 | * interval for the QH is 1, the item moves to | |
557 | * periodic_sched_ready because it must be rescheduled for | |
558 | * the next frame. Otherwise, the item moves to | |
559 | * periodic_sched_inactive. | |
560 | * @periodic_usecs: Total bandwidth claimed so far for periodic transfers. | |
561 | * This value is in microseconds per (micro)frame. The | |
562 | * assumption is that all periodic transfers may occur in | |
563 | * the same (micro)frame. | |
20f2eb9c | 564 | * @frame_usecs: Internal variable used by the microframe scheduler |
56f5b1cf PZ |
565 | * @frame_number: Frame number read from the core at SOF. The value ranges |
566 | * from 0 to HFNUM_MAX_FRNUM. | |
567 | * @periodic_qh_count: Count of periodic QHs, if using several eps. Used for | |
568 | * SOF enable/disable. | |
569 | * @free_hc_list: Free host channels in the controller. This is a list of | |
570 | * struct dwc2_host_chan items. | |
571 | * @periodic_channels: Number of host channels assigned to periodic transfers. | |
572 | * Currently assuming that there is a dedicated host | |
573 | * channel for each periodic transaction and at least one | |
574 | * host channel is available for non-periodic transactions. | |
575 | * @non_periodic_channels: Number of host channels assigned to non-periodic | |
576 | * transfers | |
20f2eb9c DC |
577 | * @available_host_channels Number of host channels available for the microframe |
578 | * scheduler to use | |
56f5b1cf PZ |
579 | * @hc_ptr_array: Array of pointers to the host channel descriptors. |
580 | * Allows accessing a host channel descriptor given the | |
581 | * host channel number. This is useful in interrupt | |
582 | * handlers. | |
583 | * @status_buf: Buffer used for data received during the status phase of | |
584 | * a control transfer. | |
585 | * @status_buf_dma: DMA address for status_buf | |
586 | * @start_work: Delayed work for handling host A-cable connection | |
587 | * @reset_work: Delayed work for handling a port reset | |
588 | * @lock: Spinlock that protects all the driver data structures | |
589 | * @priv: Stores a pointer to the struct usb_hcd | |
590 | * @otg_port: OTG port number | |
591 | * @frame_list: Frame list | |
592 | * @frame_list_dma: Frame list DMA address | |
593 | */ | |
594 | struct dwc2_hsotg { | |
595 | struct device *dev; | |
596 | void __iomem *regs; | |
9badec2f MK |
597 | /** Params detected from hardware */ |
598 | struct dwc2_hw_params hw_params; | |
599 | /** Params to actually use */ | |
56f5b1cf | 600 | struct dwc2_core_params *core_params; |
56f5b1cf | 601 | enum usb_otg_state op_state; |
c0155b9d | 602 | enum usb_dr_mode dr_mode; |
56f5b1cf PZ |
603 | |
604 | unsigned int queuing_high_bandwidth:1; | |
605 | unsigned int srp_success:1; | |
606 | ||
607 | struct workqueue_struct *wq_otg; | |
608 | struct work_struct wf_otg; | |
609 | struct timer_list wkp_timer; | |
610 | enum dwc2_lx_state lx_state; | |
611 | ||
612 | union dwc2_hcd_internal_flags { | |
613 | u32 d32; | |
614 | struct { | |
615 | unsigned port_connect_status_change:1; | |
616 | unsigned port_connect_status:1; | |
617 | unsigned port_reset_change:1; | |
618 | unsigned port_enable_change:1; | |
619 | unsigned port_suspend_change:1; | |
620 | unsigned port_over_current_change:1; | |
621 | unsigned port_l1_change:1; | |
fd4850cf | 622 | unsigned reserved:25; |
56f5b1cf PZ |
623 | } b; |
624 | } flags; | |
625 | ||
626 | struct list_head non_periodic_sched_inactive; | |
627 | struct list_head non_periodic_sched_active; | |
628 | struct list_head *non_periodic_qh_ptr; | |
629 | struct list_head periodic_sched_inactive; | |
630 | struct list_head periodic_sched_ready; | |
631 | struct list_head periodic_sched_assigned; | |
632 | struct list_head periodic_sched_queued; | |
633 | u16 periodic_usecs; | |
20f2eb9c | 634 | u16 frame_usecs[8]; |
56f5b1cf PZ |
635 | u16 frame_number; |
636 | u16 periodic_qh_count; | |
637 | ||
638 | #ifdef CONFIG_USB_DWC2_TRACK_MISSED_SOFS | |
639 | #define FRAME_NUM_ARRAY_SIZE 1000 | |
640 | u16 last_frame_num; | |
641 | u16 *frame_num_array; | |
642 | u16 *last_frame_num_array; | |
643 | int frame_num_idx; | |
644 | int dumped_frame_num_array; | |
645 | #endif | |
646 | ||
647 | struct list_head free_hc_list; | |
648 | int periodic_channels; | |
649 | int non_periodic_channels; | |
20f2eb9c | 650 | int available_host_channels; |
56f5b1cf PZ |
651 | struct dwc2_host_chan *hc_ptr_array[MAX_EPS_CHANNELS]; |
652 | u8 *status_buf; | |
653 | dma_addr_t status_buf_dma; | |
654 | #define DWC2_HCD_STATUS_BUF_SIZE 64 | |
655 | ||
656 | struct delayed_work start_work; | |
657 | struct delayed_work reset_work; | |
658 | spinlock_t lock; | |
659 | void *priv; | |
660 | u8 otg_port; | |
661 | u32 *frame_list; | |
662 | dma_addr_t frame_list_dma; | |
663 | ||
664 | /* DWC OTG HW Release versions */ | |
665 | #define DWC2_CORE_REV_2_71a 0x4f54271a | |
666 | #define DWC2_CORE_REV_2_90a 0x4f54290a | |
667 | #define DWC2_CORE_REV_2_92a 0x4f54292a | |
668 | #define DWC2_CORE_REV_2_94a 0x4f54294a | |
669 | #define DWC2_CORE_REV_3_00a 0x4f54300a | |
670 | ||
671 | #ifdef DEBUG | |
672 | u32 frrem_samples; | |
673 | u64 frrem_accum; | |
674 | ||
675 | u32 hfnum_7_samples_a; | |
676 | u64 hfnum_7_frrem_accum_a; | |
677 | u32 hfnum_0_samples_a; | |
678 | u64 hfnum_0_frrem_accum_a; | |
679 | u32 hfnum_other_samples_a; | |
680 | u64 hfnum_other_frrem_accum_a; | |
681 | ||
682 | u32 hfnum_7_samples_b; | |
683 | u64 hfnum_7_frrem_accum_b; | |
684 | u32 hfnum_0_samples_b; | |
685 | u64 hfnum_0_frrem_accum_b; | |
686 | u32 hfnum_other_samples_b; | |
687 | u64 hfnum_other_frrem_accum_b; | |
688 | #endif | |
689 | }; | |
690 | ||
691 | /* Reasons for halting a host channel */ | |
692 | enum dwc2_halt_status { | |
693 | DWC2_HC_XFER_NO_HALT_STATUS, | |
694 | DWC2_HC_XFER_COMPLETE, | |
695 | DWC2_HC_XFER_URB_COMPLETE, | |
696 | DWC2_HC_XFER_ACK, | |
697 | DWC2_HC_XFER_NAK, | |
698 | DWC2_HC_XFER_NYET, | |
699 | DWC2_HC_XFER_STALL, | |
700 | DWC2_HC_XFER_XACT_ERR, | |
701 | DWC2_HC_XFER_FRAME_OVERRUN, | |
702 | DWC2_HC_XFER_BABBLE_ERR, | |
703 | DWC2_HC_XFER_DATA_TOGGLE_ERR, | |
704 | DWC2_HC_XFER_AHB_ERR, | |
705 | DWC2_HC_XFER_PERIODIC_INCOMPLETE, | |
706 | DWC2_HC_XFER_URB_DEQUEUE, | |
707 | }; | |
708 | ||
709 | /* | |
710 | * The following functions support initialization of the core driver component | |
711 | * and the DWC_otg controller | |
712 | */ | |
713 | extern void dwc2_core_host_init(struct dwc2_hsotg *hsotg); | |
714 | ||
715 | /* | |
716 | * Host core Functions. | |
717 | * The following functions support managing the DWC_otg controller in host | |
718 | * mode. | |
719 | */ | |
720 | extern void dwc2_hc_init(struct dwc2_hsotg *hsotg, struct dwc2_host_chan *chan); | |
721 | extern void dwc2_hc_halt(struct dwc2_hsotg *hsotg, struct dwc2_host_chan *chan, | |
722 | enum dwc2_halt_status halt_status); | |
723 | extern void dwc2_hc_cleanup(struct dwc2_hsotg *hsotg, | |
724 | struct dwc2_host_chan *chan); | |
725 | extern void dwc2_hc_start_transfer(struct dwc2_hsotg *hsotg, | |
726 | struct dwc2_host_chan *chan); | |
727 | extern void dwc2_hc_start_transfer_ddma(struct dwc2_hsotg *hsotg, | |
728 | struct dwc2_host_chan *chan); | |
729 | extern int dwc2_hc_continue_transfer(struct dwc2_hsotg *hsotg, | |
730 | struct dwc2_host_chan *chan); | |
731 | extern void dwc2_hc_do_ping(struct dwc2_hsotg *hsotg, | |
732 | struct dwc2_host_chan *chan); | |
733 | extern void dwc2_enable_host_interrupts(struct dwc2_hsotg *hsotg); | |
734 | extern void dwc2_disable_host_interrupts(struct dwc2_hsotg *hsotg); | |
735 | ||
736 | extern u32 dwc2_calc_frame_interval(struct dwc2_hsotg *hsotg); | |
057715f2 | 737 | extern bool dwc2_is_controller_alive(struct dwc2_hsotg *hsotg); |
56f5b1cf PZ |
738 | |
739 | /* | |
740 | * Common core Functions. | |
741 | * The following functions support managing the DWC_otg controller in either | |
742 | * device or host mode. | |
743 | */ | |
744 | extern void dwc2_read_packet(struct dwc2_hsotg *hsotg, u8 *dest, u16 bytes); | |
745 | extern void dwc2_flush_tx_fifo(struct dwc2_hsotg *hsotg, const int num); | |
746 | extern void dwc2_flush_rx_fifo(struct dwc2_hsotg *hsotg); | |
747 | ||
6706c721 | 748 | extern int dwc2_core_init(struct dwc2_hsotg *hsotg, bool select_phy, int irq); |
56f5b1cf PZ |
749 | extern void dwc2_enable_global_interrupts(struct dwc2_hsotg *hcd); |
750 | extern void dwc2_disable_global_interrupts(struct dwc2_hsotg *hcd); | |
751 | ||
752 | /* This function should be called on every hardware interrupt. */ | |
753 | extern irqreturn_t dwc2_handle_common_intr(int irq, void *dev); | |
754 | ||
755 | /* OTG Core Parameters */ | |
756 | ||
757 | /* | |
758 | * Specifies the OTG capabilities. The driver will automatically | |
759 | * detect the value for this parameter if none is specified. | |
760 | * 0 - HNP and SRP capable (default) | |
761 | * 1 - SRP Only capable | |
762 | * 2 - No HNP/SRP capable | |
763 | */ | |
7218dae7 | 764 | extern void dwc2_set_param_otg_cap(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
765 | #define DWC2_CAP_PARAM_HNP_SRP_CAPABLE 0 |
766 | #define DWC2_CAP_PARAM_SRP_ONLY_CAPABLE 1 | |
767 | #define DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE 2 | |
768 | ||
769 | /* | |
770 | * Specifies whether to use slave or DMA mode for accessing the data | |
771 | * FIFOs. The driver will automatically detect the value for this | |
772 | * parameter if none is specified. | |
773 | * 0 - Slave | |
774 | * 1 - DMA (default, if available) | |
775 | */ | |
7218dae7 | 776 | extern void dwc2_set_param_dma_enable(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
777 | |
778 | /* | |
779 | * When DMA mode is enabled specifies whether to use | |
780 | * address DMA or DMA Descritor mode for accessing the data | |
781 | * FIFOs in device mode. The driver will automatically detect | |
782 | * the value for this parameter if none is specified. | |
783 | * 0 - address DMA | |
784 | * 1 - DMA Descriptor(default, if available) | |
785 | */ | |
7218dae7 | 786 | extern void dwc2_set_param_dma_desc_enable(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
787 | |
788 | /* | |
789 | * Specifies the maximum speed of operation in host and device mode. | |
790 | * The actual speed depends on the speed of the attached device and | |
791 | * the value of phy_type. The actual speed depends on the speed of the | |
792 | * attached device. | |
793 | * 0 - High Speed (default) | |
794 | * 1 - Full Speed | |
795 | */ | |
7218dae7 | 796 | extern void dwc2_set_param_speed(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
797 | #define DWC2_SPEED_PARAM_HIGH 0 |
798 | #define DWC2_SPEED_PARAM_FULL 1 | |
799 | ||
800 | /* | |
801 | * Specifies whether low power mode is supported when attached | |
802 | * to a Full Speed or Low Speed device in host mode. | |
803 | * | |
804 | * 0 - Don't support low power mode (default) | |
805 | * 1 - Support low power mode | |
806 | */ | |
7218dae7 PZ |
807 | extern void dwc2_set_param_host_support_fs_ls_low_power( |
808 | struct dwc2_hsotg *hsotg, int val); | |
56f5b1cf PZ |
809 | |
810 | /* | |
811 | * Specifies the PHY clock rate in low power mode when connected to a | |
812 | * Low Speed device in host mode. This parameter is applicable only if | |
813 | * HOST_SUPPORT_FS_LS_LOW_POWER is enabled. If PHY_TYPE is set to FS | |
814 | * then defaults to 6 MHZ otherwise 48 MHZ. | |
815 | * | |
816 | * 0 - 48 MHz | |
817 | * 1 - 6 MHz | |
818 | */ | |
7218dae7 PZ |
819 | extern void dwc2_set_param_host_ls_low_power_phy_clk(struct dwc2_hsotg *hsotg, |
820 | int val); | |
56f5b1cf PZ |
821 | #define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ 0 |
822 | #define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ 1 | |
823 | ||
824 | /* | |
825 | * 0 - Use cC FIFO size parameters | |
826 | * 1 - Allow dynamic FIFO sizing (default) | |
827 | */ | |
7218dae7 PZ |
828 | extern void dwc2_set_param_enable_dynamic_fifo(struct dwc2_hsotg *hsotg, |
829 | int val); | |
56f5b1cf PZ |
830 | |
831 | /* | |
832 | * Number of 4-byte words in the Rx FIFO in host mode when dynamic | |
833 | * FIFO sizing is enabled. | |
834 | * 16 to 32768 (default 1024) | |
835 | */ | |
7218dae7 | 836 | extern void dwc2_set_param_host_rx_fifo_size(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
837 | |
838 | /* | |
839 | * Number of 4-byte words in the non-periodic Tx FIFO in host mode | |
840 | * when Dynamic FIFO sizing is enabled in the core. | |
841 | * 16 to 32768 (default 256) | |
842 | */ | |
7218dae7 PZ |
843 | extern void dwc2_set_param_host_nperio_tx_fifo_size(struct dwc2_hsotg *hsotg, |
844 | int val); | |
56f5b1cf PZ |
845 | |
846 | /* | |
847 | * Number of 4-byte words in the host periodic Tx FIFO when dynamic | |
848 | * FIFO sizing is enabled. | |
849 | * 16 to 32768 (default 256) | |
850 | */ | |
7218dae7 PZ |
851 | extern void dwc2_set_param_host_perio_tx_fifo_size(struct dwc2_hsotg *hsotg, |
852 | int val); | |
56f5b1cf PZ |
853 | |
854 | /* | |
855 | * The maximum transfer size supported in bytes. | |
856 | * 2047 to 65,535 (default 65,535) | |
857 | */ | |
7218dae7 | 858 | extern void dwc2_set_param_max_transfer_size(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
859 | |
860 | /* | |
861 | * The maximum number of packets in a transfer. | |
862 | * 15 to 511 (default 511) | |
863 | */ | |
7218dae7 | 864 | extern void dwc2_set_param_max_packet_count(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
865 | |
866 | /* | |
867 | * The number of host channel registers to use. | |
868 | * 1 to 16 (default 11) | |
869 | * Note: The FPGA configuration supports a maximum of 11 host channels. | |
870 | */ | |
7218dae7 | 871 | extern void dwc2_set_param_host_channels(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
872 | |
873 | /* | |
874 | * Specifies the type of PHY interface to use. By default, the driver | |
875 | * will automatically detect the phy_type. | |
876 | * | |
877 | * 0 - Full Speed PHY | |
878 | * 1 - UTMI+ (default) | |
879 | * 2 - ULPI | |
880 | */ | |
7218dae7 | 881 | extern void dwc2_set_param_phy_type(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
882 | #define DWC2_PHY_TYPE_PARAM_FS 0 |
883 | #define DWC2_PHY_TYPE_PARAM_UTMI 1 | |
884 | #define DWC2_PHY_TYPE_PARAM_ULPI 2 | |
885 | ||
886 | /* | |
887 | * Specifies the UTMI+ Data Width. This parameter is | |
888 | * applicable for a PHY_TYPE of UTMI+ or ULPI. (For a ULPI | |
889 | * PHY_TYPE, this parameter indicates the data width between | |
890 | * the MAC and the ULPI Wrapper.) Also, this parameter is | |
891 | * applicable only if the OTG_HSPHY_WIDTH cC parameter was set | |
892 | * to "8 and 16 bits", meaning that the core has been | |
893 | * configured to work at either data path width. | |
894 | * | |
895 | * 8 or 16 bits (default 16) | |
896 | */ | |
7218dae7 | 897 | extern void dwc2_set_param_phy_utmi_width(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
898 | |
899 | /* | |
900 | * Specifies whether the ULPI operates at double or single | |
901 | * data rate. This parameter is only applicable if PHY_TYPE is | |
902 | * ULPI. | |
903 | * | |
904 | * 0 - single data rate ULPI interface with 8 bit wide data | |
905 | * bus (default) | |
906 | * 1 - double data rate ULPI interface with 4 bit wide data | |
907 | * bus | |
908 | */ | |
7218dae7 | 909 | extern void dwc2_set_param_phy_ulpi_ddr(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
910 | |
911 | /* | |
912 | * Specifies whether to use the internal or external supply to | |
913 | * drive the vbus with a ULPI phy. | |
914 | */ | |
7218dae7 | 915 | extern void dwc2_set_param_phy_ulpi_ext_vbus(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
916 | #define DWC2_PHY_ULPI_INTERNAL_VBUS 0 |
917 | #define DWC2_PHY_ULPI_EXTERNAL_VBUS 1 | |
918 | ||
919 | /* | |
920 | * Specifies whether to use the I2Cinterface for full speed PHY. This | |
921 | * parameter is only applicable if PHY_TYPE is FS. | |
922 | * 0 - No (default) | |
923 | * 1 - Yes | |
924 | */ | |
7218dae7 | 925 | extern void dwc2_set_param_i2c_enable(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf | 926 | |
7218dae7 | 927 | extern void dwc2_set_param_ulpi_fs_ls(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf | 928 | |
7218dae7 | 929 | extern void dwc2_set_param_ts_dline(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
930 | |
931 | /* | |
932 | * Specifies whether dedicated transmit FIFOs are | |
933 | * enabled for non periodic IN endpoints in device mode | |
934 | * 0 - No | |
935 | * 1 - Yes | |
936 | */ | |
7218dae7 PZ |
937 | extern void dwc2_set_param_en_multiple_tx_fifo(struct dwc2_hsotg *hsotg, |
938 | int val); | |
56f5b1cf | 939 | |
7218dae7 | 940 | extern void dwc2_set_param_reload_ctl(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf | 941 | |
7218dae7 | 942 | extern void dwc2_set_param_ahbcfg(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf | 943 | |
7218dae7 | 944 | extern void dwc2_set_param_otg_ver(struct dwc2_hsotg *hsotg, int val); |
56f5b1cf PZ |
945 | |
946 | /* | |
947 | * Dump core registers and SPRAM | |
948 | */ | |
949 | extern void dwc2_dump_dev_registers(struct dwc2_hsotg *hsotg); | |
950 | extern void dwc2_dump_host_registers(struct dwc2_hsotg *hsotg); | |
951 | extern void dwc2_dump_global_registers(struct dwc2_hsotg *hsotg); | |
952 | ||
953 | /* | |
954 | * Return OTG version - either 1.3 or 2.0 | |
955 | */ | |
956 | extern u16 dwc2_get_otg_version(struct dwc2_hsotg *hsotg); | |
957 | ||
958 | #endif /* __DWC2_CORE_H__ */ |