Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * file_storage.c -- File-backed USB Storage Gadget, for USB development | |
3 | * | |
79a7d9ee | 4 | * Copyright (C) 2003-2007 Alan Stern |
1da177e4 LT |
5 | * All rights reserved. |
6 | * | |
7 | * Redistribution and use in source and binary forms, with or without | |
8 | * modification, are permitted provided that the following conditions | |
9 | * are met: | |
10 | * 1. Redistributions of source code must retain the above copyright | |
11 | * notice, this list of conditions, and the following disclaimer, | |
12 | * without modification. | |
13 | * 2. Redistributions in binary form must reproduce the above copyright | |
14 | * notice, this list of conditions and the following disclaimer in the | |
15 | * documentation and/or other materials provided with the distribution. | |
16 | * 3. The names of the above-listed copyright holders may not be used | |
17 | * to endorse or promote products derived from this software without | |
18 | * specific prior written permission. | |
19 | * | |
20 | * ALTERNATIVELY, this software may be distributed under the terms of the | |
21 | * GNU General Public License ("GPL") as published by the Free Software | |
22 | * Foundation, either version 2 of that License or (at your option) any | |
23 | * later version. | |
24 | * | |
25 | * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS | |
26 | * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, | |
27 | * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR | |
28 | * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR | |
29 | * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, | |
30 | * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, | |
31 | * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR | |
32 | * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF | |
33 | * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING | |
34 | * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS | |
35 | * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
36 | */ | |
37 | ||
38 | ||
39 | /* | |
40 | * The File-backed Storage Gadget acts as a USB Mass Storage device, | |
41 | * appearing to the host as a disk drive. In addition to providing an | |
42 | * example of a genuinely useful gadget driver for a USB device, it also | |
43 | * illustrates a technique of double-buffering for increased throughput. | |
44 | * Last but not least, it gives an easy way to probe the behavior of the | |
45 | * Mass Storage drivers in a USB host. | |
46 | * | |
47 | * Backing storage is provided by a regular file or a block device, specified | |
48 | * by the "file" module parameter. Access can be limited to read-only by | |
49 | * setting the optional "ro" module parameter. The gadget will indicate that | |
50 | * it has removable media if the optional "removable" module parameter is set. | |
51 | * | |
52 | * The gadget supports the Control-Bulk (CB), Control-Bulk-Interrupt (CBI), | |
53 | * and Bulk-Only (also known as Bulk-Bulk-Bulk or BBB) transports, selected | |
54 | * by the optional "transport" module parameter. It also supports the | |
55 | * following protocols: RBC (0x01), ATAPI or SFF-8020i (0x02), QIC-157 (0c03), | |
56 | * UFI (0x04), SFF-8070i (0x05), and transparent SCSI (0x06), selected by | |
57 | * the optional "protocol" module parameter. In addition, the default | |
58 | * Vendor ID, Product ID, and release number can be overridden. | |
59 | * | |
60 | * There is support for multiple logical units (LUNs), each of which has | |
61 | * its own backing file. The number of LUNs can be set using the optional | |
62 | * "luns" module parameter (anywhere from 1 to 8), and the corresponding | |
63 | * files are specified using comma-separated lists for "file" and "ro". | |
64 | * The default number of LUNs is taken from the number of "file" elements; | |
65 | * it is 1 if "file" is not given. If "removable" is not set then a backing | |
66 | * file must be specified for each LUN. If it is set, then an unspecified | |
67 | * or empty backing filename means the LUN's medium is not loaded. | |
68 | * | |
69 | * Requirements are modest; only a bulk-in and a bulk-out endpoint are | |
70 | * needed (an interrupt-out endpoint is also needed for CBI). The memory | |
71 | * requirement amounts to two 16K buffers, size configurable by a parameter. | |
72 | * Support is included for both full-speed and high-speed operation. | |
73 | * | |
14cd5f8e AS |
74 | * Note that the driver is slightly non-portable in that it assumes a |
75 | * single memory/DMA buffer will be useable for bulk-in, bulk-out, and | |
76 | * interrupt-in endpoints. With most device controllers this isn't an | |
77 | * issue, but there may be some with hardware restrictions that prevent | |
78 | * a buffer from being used by more than one endpoint. | |
79 | * | |
1da177e4 LT |
80 | * Module options: |
81 | * | |
82 | * file=filename[,filename...] | |
83 | * Required if "removable" is not set, names of | |
84 | * the files or block devices used for | |
85 | * backing storage | |
86 | * ro=b[,b...] Default false, booleans for read-only access | |
87 | * removable Default false, boolean for removable media | |
88 | * luns=N Default N = number of filenames, number of | |
89 | * LUNs to support | |
d794ac7a AS |
90 | * stall Default determined according to the type of |
91 | * USB device controller (usually true), | |
92 | * boolean to permit the driver to halt | |
93 | * bulk endpoints | |
1da177e4 LT |
94 | * transport=XXX Default BBB, transport name (CB, CBI, or BBB) |
95 | * protocol=YYY Default SCSI, protocol name (RBC, 8020 or | |
96 | * ATAPI, QIC, UFI, 8070, or SCSI; | |
97 | * also 1 - 6) | |
98 | * vendor=0xVVVV Default 0x0525 (NetChip), USB Vendor ID | |
99 | * product=0xPPPP Default 0xa4a5 (FSG), USB Product ID | |
100 | * release=0xRRRR Override the USB release number (bcdDevice) | |
101 | * buflen=N Default N=16384, buffer size used (will be | |
102 | * rounded down to a multiple of | |
103 | * PAGE_CACHE_SIZE) | |
1da177e4 LT |
104 | * |
105 | * If CONFIG_USB_FILE_STORAGE_TEST is not set, only the "file", "ro", | |
d794ac7a AS |
106 | * "removable", "luns", and "stall" options are available; default values |
107 | * are used for everything else. | |
1da177e4 LT |
108 | * |
109 | * The pathnames of the backing files and the ro settings are available in | |
110 | * the attribute files "file" and "ro" in the lun<n> subdirectory of the | |
111 | * gadget's sysfs directory. If the "removable" option is set, writing to | |
112 | * these files will simulate ejecting/loading the medium (writing an empty | |
113 | * line means eject) and adjusting a write-enable tab. Changes to the ro | |
114 | * setting are not allowed when the medium is loaded. | |
115 | * | |
116 | * This gadget driver is heavily based on "Gadget Zero" by David Brownell. | |
aafe5bd6 AS |
117 | * The driver's SCSI command interface was based on the "Information |
118 | * technology - Small Computer System Interface - 2" document from | |
119 | * X3T9.2 Project 375D, Revision 10L, 7-SEP-93, available at | |
120 | * <http://www.t10.org/ftp/t10/drafts/s2/s2-r10l.pdf>. The single exception | |
121 | * is opcode 0x23 (READ FORMAT CAPACITIES), which was based on the | |
122 | * "Universal Serial Bus Mass Storage Class UFI Command Specification" | |
123 | * document, Revision 1.0, December 14, 1998, available at | |
124 | * <http://www.usb.org/developers/devclass_docs/usbmass-ufi10.pdf>. | |
1da177e4 LT |
125 | */ |
126 | ||
127 | ||
128 | /* | |
129 | * Driver Design | |
130 | * | |
131 | * The FSG driver is fairly straightforward. There is a main kernel | |
132 | * thread that handles most of the work. Interrupt routines field | |
133 | * callbacks from the controller driver: bulk- and interrupt-request | |
134 | * completion notifications, endpoint-0 events, and disconnect events. | |
135 | * Completion events are passed to the main thread by wakeup calls. Many | |
136 | * ep0 requests are handled at interrupt time, but SetInterface, | |
137 | * SetConfiguration, and device reset requests are forwarded to the | |
138 | * thread in the form of "exceptions" using SIGUSR1 signals (since they | |
139 | * should interrupt any ongoing file I/O operations). | |
140 | * | |
141 | * The thread's main routine implements the standard command/data/status | |
142 | * parts of a SCSI interaction. It and its subroutines are full of tests | |
143 | * for pending signals/exceptions -- all this polling is necessary since | |
144 | * the kernel has no setjmp/longjmp equivalents. (Maybe this is an | |
145 | * indication that the driver really wants to be running in userspace.) | |
146 | * An important point is that so long as the thread is alive it keeps an | |
147 | * open reference to the backing file. This will prevent unmounting | |
148 | * the backing file's underlying filesystem and could cause problems | |
149 | * during system shutdown, for example. To prevent such problems, the | |
150 | * thread catches INT, TERM, and KILL signals and converts them into | |
151 | * an EXIT exception. | |
152 | * | |
153 | * In normal operation the main thread is started during the gadget's | |
154 | * fsg_bind() callback and stopped during fsg_unbind(). But it can also | |
155 | * exit when it receives a signal, and there's no point leaving the | |
156 | * gadget running when the thread is dead. So just before the thread | |
157 | * exits, it deregisters the gadget driver. This makes things a little | |
158 | * tricky: The driver is deregistered at two places, and the exiting | |
159 | * thread can indirectly call fsg_unbind() which in turn can tell the | |
160 | * thread to exit. The first problem is resolved through the use of the | |
161 | * REGISTERED atomic bitflag; the driver will only be deregistered once. | |
162 | * The second problem is resolved by having fsg_unbind() check | |
163 | * fsg->state; it won't try to stop the thread if the state is already | |
164 | * FSG_STATE_TERMINATED. | |
165 | * | |
166 | * To provide maximum throughput, the driver uses a circular pipeline of | |
167 | * buffer heads (struct fsg_buffhd). In principle the pipeline can be | |
168 | * arbitrarily long; in practice the benefits don't justify having more | |
169 | * than 2 stages (i.e., double buffering). But it helps to think of the | |
170 | * pipeline as being a long one. Each buffer head contains a bulk-in and | |
171 | * a bulk-out request pointer (since the buffer can be used for both | |
172 | * output and input -- directions always are given from the host's | |
173 | * point of view) as well as a pointer to the buffer and various state | |
174 | * variables. | |
175 | * | |
176 | * Use of the pipeline follows a simple protocol. There is a variable | |
177 | * (fsg->next_buffhd_to_fill) that points to the next buffer head to use. | |
178 | * At any time that buffer head may still be in use from an earlier | |
179 | * request, so each buffer head has a state variable indicating whether | |
180 | * it is EMPTY, FULL, or BUSY. Typical use involves waiting for the | |
181 | * buffer head to be EMPTY, filling the buffer either by file I/O or by | |
182 | * USB I/O (during which the buffer head is BUSY), and marking the buffer | |
183 | * head FULL when the I/O is complete. Then the buffer will be emptied | |
184 | * (again possibly by USB I/O, during which it is marked BUSY) and | |
185 | * finally marked EMPTY again (possibly by a completion routine). | |
186 | * | |
187 | * A module parameter tells the driver to avoid stalling the bulk | |
188 | * endpoints wherever the transport specification allows. This is | |
189 | * necessary for some UDCs like the SuperH, which cannot reliably clear a | |
190 | * halt on a bulk endpoint. However, under certain circumstances the | |
191 | * Bulk-only specification requires a stall. In such cases the driver | |
192 | * will halt the endpoint and set a flag indicating that it should clear | |
193 | * the halt in software during the next device reset. Hopefully this | |
194 | * will permit everything to work correctly. Furthermore, although the | |
195 | * specification allows the bulk-out endpoint to halt when the host sends | |
196 | * too much data, implementing this would cause an unavoidable race. | |
197 | * The driver will always use the "no-stall" approach for OUT transfers. | |
198 | * | |
199 | * One subtle point concerns sending status-stage responses for ep0 | |
200 | * requests. Some of these requests, such as device reset, can involve | |
201 | * interrupting an ongoing file I/O operation, which might take an | |
202 | * arbitrarily long time. During that delay the host might give up on | |
203 | * the original ep0 request and issue a new one. When that happens the | |
204 | * driver should not notify the host about completion of the original | |
205 | * request, as the host will no longer be waiting for it. So the driver | |
206 | * assigns to each ep0 request a unique tag, and it keeps track of the | |
207 | * tag value of the request associated with a long-running exception | |
208 | * (device-reset, interface-change, or configuration-change). When the | |
209 | * exception handler is finished, the status-stage response is submitted | |
210 | * only if the current ep0 request tag is equal to the exception request | |
211 | * tag. Thus only the most recently received ep0 request will get a | |
212 | * status-stage response. | |
213 | * | |
214 | * Warning: This driver source file is too long. It ought to be split up | |
215 | * into a header file plus about 3 separate .c files, to handle the details | |
216 | * of the Gadget, USB Mass Storage, and SCSI protocols. | |
217 | */ | |
218 | ||
219 | ||
2e806f67 | 220 | /* #define VERBOSE_DEBUG */ |
79a7d9ee | 221 | /* #define DUMP_MSGS */ |
1da177e4 | 222 | |
1da177e4 | 223 | |
1da177e4 | 224 | #include <linux/blkdev.h> |
1da177e4 LT |
225 | #include <linux/completion.h> |
226 | #include <linux/dcache.h> | |
227 | #include <linux/delay.h> | |
228 | #include <linux/device.h> | |
229 | #include <linux/fcntl.h> | |
230 | #include <linux/file.h> | |
231 | #include <linux/fs.h> | |
87c4252a | 232 | #include <linux/kref.h> |
22efcf4a | 233 | #include <linux/kthread.h> |
1da177e4 | 234 | #include <linux/limits.h> |
1da177e4 | 235 | #include <linux/rwsem.h> |
1da177e4 LT |
236 | #include <linux/slab.h> |
237 | #include <linux/spinlock.h> | |
238 | #include <linux/string.h> | |
7dfb7103 | 239 | #include <linux/freezer.h> |
1da177e4 | 240 | #include <linux/utsname.h> |
1da177e4 | 241 | |
5f848137 | 242 | #include <linux/usb/ch9.h> |
9454a57a | 243 | #include <linux/usb/gadget.h> |
1da177e4 LT |
244 | |
245 | #include "gadget_chips.h" | |
246 | ||
247 | ||
248 | /*-------------------------------------------------------------------------*/ | |
249 | ||
250 | #define DRIVER_DESC "File-backed Storage Gadget" | |
251 | #define DRIVER_NAME "g_file_storage" | |
79a7d9ee | 252 | #define DRIVER_VERSION "7 August 2007" |
1da177e4 LT |
253 | |
254 | static const char longname[] = DRIVER_DESC; | |
255 | static const char shortname[] = DRIVER_NAME; | |
256 | ||
257 | MODULE_DESCRIPTION(DRIVER_DESC); | |
258 | MODULE_AUTHOR("Alan Stern"); | |
259 | MODULE_LICENSE("Dual BSD/GPL"); | |
260 | ||
261 | /* Thanks to NetChip Technologies for donating this product ID. | |
262 | * | |
263 | * DO NOT REUSE THESE IDs with any other driver!! Ever!! | |
264 | * Instead: allocate your own, using normal USB-IF procedures. */ | |
265 | #define DRIVER_VENDOR_ID 0x0525 // NetChip | |
266 | #define DRIVER_PRODUCT_ID 0xa4a5 // Linux-USB File-backed Storage Gadget | |
267 | ||
268 | ||
269 | /* | |
270 | * This driver assumes self-powered hardware and has no way for users to | |
271 | * trigger remote wakeup. It uses autoconfiguration to select endpoints | |
272 | * and endpoint addresses. | |
273 | */ | |
274 | ||
275 | ||
276 | /*-------------------------------------------------------------------------*/ | |
277 | ||
1da177e4 | 278 | #ifdef DEBUG |
1da177e4 | 279 | #define LDBG(lun,fmt,args...) \ |
79a7d9ee | 280 | dev_dbg(&(lun)->dev , fmt , ## args) |
1da177e4 LT |
281 | #define MDBG(fmt,args...) \ |
282 | printk(KERN_DEBUG DRIVER_NAME ": " fmt , ## args) | |
283 | #else | |
1da177e4 LT |
284 | #define LDBG(lun,fmt,args...) \ |
285 | do { } while (0) | |
286 | #define MDBG(fmt,args...) \ | |
287 | do { } while (0) | |
2e806f67 | 288 | #undef VERBOSE_DEBUG |
1da177e4 LT |
289 | #undef DUMP_MSGS |
290 | #endif /* DEBUG */ | |
291 | ||
2e806f67 | 292 | #ifdef VERBOSE_DEBUG |
1da177e4 LT |
293 | #define VLDBG LDBG |
294 | #else | |
1da177e4 LT |
295 | #define VLDBG(lun,fmt,args...) \ |
296 | do { } while (0) | |
2e806f67 | 297 | #endif /* VERBOSE_DEBUG */ |
1da177e4 | 298 | |
1da177e4 | 299 | #define LERROR(lun,fmt,args...) \ |
79a7d9ee | 300 | dev_err(&(lun)->dev , fmt , ## args) |
1da177e4 | 301 | #define LWARN(lun,fmt,args...) \ |
79a7d9ee | 302 | dev_warn(&(lun)->dev , fmt , ## args) |
1da177e4 | 303 | #define LINFO(lun,fmt,args...) \ |
79a7d9ee | 304 | dev_info(&(lun)->dev , fmt , ## args) |
1da177e4 LT |
305 | |
306 | #define MINFO(fmt,args...) \ | |
307 | printk(KERN_INFO DRIVER_NAME ": " fmt , ## args) | |
308 | ||
2e806f67 DB |
309 | #define DBG(d, fmt, args...) \ |
310 | dev_dbg(&(d)->gadget->dev , fmt , ## args) | |
311 | #define VDBG(d, fmt, args...) \ | |
312 | dev_vdbg(&(d)->gadget->dev , fmt , ## args) | |
313 | #define ERROR(d, fmt, args...) \ | |
314 | dev_err(&(d)->gadget->dev , fmt , ## args) | |
315 | #define WARN(d, fmt, args...) \ | |
316 | dev_warn(&(d)->gadget->dev , fmt , ## args) | |
317 | #define INFO(d, fmt, args...) \ | |
318 | dev_info(&(d)->gadget->dev , fmt , ## args) | |
319 | ||
1da177e4 LT |
320 | |
321 | /*-------------------------------------------------------------------------*/ | |
322 | ||
323 | /* Encapsulate the module parameter settings */ | |
324 | ||
325 | #define MAX_LUNS 8 | |
326 | ||
1da177e4 | 327 | static struct { |
aafe5bd6 AS |
328 | char *file[MAX_LUNS]; |
329 | int ro[MAX_LUNS]; | |
2e806f67 DB |
330 | unsigned int num_filenames; |
331 | unsigned int num_ros; | |
1da177e4 LT |
332 | unsigned int nluns; |
333 | ||
d794ac7a AS |
334 | int removable; |
335 | int can_stall; | |
336 | ||
1da177e4 LT |
337 | char *transport_parm; |
338 | char *protocol_parm; | |
1da177e4 LT |
339 | unsigned short vendor; |
340 | unsigned short product; | |
341 | unsigned short release; | |
342 | unsigned int buflen; | |
1da177e4 LT |
343 | |
344 | int transport_type; | |
345 | char *transport_name; | |
346 | int protocol_type; | |
347 | char *protocol_name; | |
348 | ||
349 | } mod_data = { // Default values | |
350 | .transport_parm = "BBB", | |
351 | .protocol_parm = "SCSI", | |
352 | .removable = 0, | |
d794ac7a | 353 | .can_stall = 1, |
1da177e4 LT |
354 | .vendor = DRIVER_VENDOR_ID, |
355 | .product = DRIVER_PRODUCT_ID, | |
356 | .release = 0xffff, // Use controller chip type | |
357 | .buflen = 16384, | |
1da177e4 LT |
358 | }; |
359 | ||
360 | ||
aafe5bd6 AS |
361 | module_param_array_named(file, mod_data.file, charp, &mod_data.num_filenames, |
362 | S_IRUGO); | |
1da177e4 LT |
363 | MODULE_PARM_DESC(file, "names of backing files or devices"); |
364 | ||
aafe5bd6 | 365 | module_param_array_named(ro, mod_data.ro, bool, &mod_data.num_ros, S_IRUGO); |
1da177e4 LT |
366 | MODULE_PARM_DESC(ro, "true to force read-only"); |
367 | ||
368 | module_param_named(luns, mod_data.nluns, uint, S_IRUGO); | |
369 | MODULE_PARM_DESC(luns, "number of LUNs"); | |
370 | ||
371 | module_param_named(removable, mod_data.removable, bool, S_IRUGO); | |
372 | MODULE_PARM_DESC(removable, "true to simulate removable media"); | |
373 | ||
d794ac7a AS |
374 | module_param_named(stall, mod_data.can_stall, bool, S_IRUGO); |
375 | MODULE_PARM_DESC(stall, "false to prevent bulk stalls"); | |
376 | ||
1da177e4 LT |
377 | |
378 | /* In the non-TEST version, only the module parameters listed above | |
379 | * are available. */ | |
380 | #ifdef CONFIG_USB_FILE_STORAGE_TEST | |
381 | ||
382 | module_param_named(transport, mod_data.transport_parm, charp, S_IRUGO); | |
383 | MODULE_PARM_DESC(transport, "type of transport (BBB, CBI, or CB)"); | |
384 | ||
385 | module_param_named(protocol, mod_data.protocol_parm, charp, S_IRUGO); | |
386 | MODULE_PARM_DESC(protocol, "type of protocol (RBC, 8020, QIC, UFI, " | |
387 | "8070, or SCSI)"); | |
388 | ||
389 | module_param_named(vendor, mod_data.vendor, ushort, S_IRUGO); | |
390 | MODULE_PARM_DESC(vendor, "USB Vendor ID"); | |
391 | ||
392 | module_param_named(product, mod_data.product, ushort, S_IRUGO); | |
393 | MODULE_PARM_DESC(product, "USB Product ID"); | |
394 | ||
395 | module_param_named(release, mod_data.release, ushort, S_IRUGO); | |
396 | MODULE_PARM_DESC(release, "USB release number"); | |
397 | ||
398 | module_param_named(buflen, mod_data.buflen, uint, S_IRUGO); | |
399 | MODULE_PARM_DESC(buflen, "I/O buffer size"); | |
400 | ||
1da177e4 LT |
401 | #endif /* CONFIG_USB_FILE_STORAGE_TEST */ |
402 | ||
403 | ||
404 | /*-------------------------------------------------------------------------*/ | |
405 | ||
406 | /* USB protocol value = the transport method */ | |
407 | #define USB_PR_CBI 0x00 // Control/Bulk/Interrupt | |
408 | #define USB_PR_CB 0x01 // Control/Bulk w/o interrupt | |
409 | #define USB_PR_BULK 0x50 // Bulk-only | |
410 | ||
411 | /* USB subclass value = the protocol encapsulation */ | |
412 | #define USB_SC_RBC 0x01 // Reduced Block Commands (flash) | |
413 | #define USB_SC_8020 0x02 // SFF-8020i, MMC-2, ATAPI (CD-ROM) | |
414 | #define USB_SC_QIC 0x03 // QIC-157 (tape) | |
415 | #define USB_SC_UFI 0x04 // UFI (floppy) | |
416 | #define USB_SC_8070 0x05 // SFF-8070i (removable) | |
417 | #define USB_SC_SCSI 0x06 // Transparent SCSI | |
418 | ||
419 | /* Bulk-only data structures */ | |
420 | ||
421 | /* Command Block Wrapper */ | |
422 | struct bulk_cb_wrap { | |
423 | __le32 Signature; // Contains 'USBC' | |
424 | u32 Tag; // Unique per command id | |
425 | __le32 DataTransferLength; // Size of the data | |
426 | u8 Flags; // Direction in bit 7 | |
427 | u8 Lun; // LUN (normally 0) | |
428 | u8 Length; // Of the CDB, <= MAX_COMMAND_SIZE | |
429 | u8 CDB[16]; // Command Data Block | |
430 | }; | |
431 | ||
432 | #define USB_BULK_CB_WRAP_LEN 31 | |
433 | #define USB_BULK_CB_SIG 0x43425355 // Spells out USBC | |
434 | #define USB_BULK_IN_FLAG 0x80 | |
435 | ||
436 | /* Command Status Wrapper */ | |
437 | struct bulk_cs_wrap { | |
438 | __le32 Signature; // Should = 'USBS' | |
439 | u32 Tag; // Same as original command | |
440 | __le32 Residue; // Amount not transferred | |
441 | u8 Status; // See below | |
442 | }; | |
443 | ||
444 | #define USB_BULK_CS_WRAP_LEN 13 | |
445 | #define USB_BULK_CS_SIG 0x53425355 // Spells out 'USBS' | |
446 | #define USB_STATUS_PASS 0 | |
447 | #define USB_STATUS_FAIL 1 | |
448 | #define USB_STATUS_PHASE_ERROR 2 | |
449 | ||
450 | /* Bulk-only class specific requests */ | |
451 | #define USB_BULK_RESET_REQUEST 0xff | |
452 | #define USB_BULK_GET_MAX_LUN_REQUEST 0xfe | |
453 | ||
454 | ||
455 | /* CBI Interrupt data structure */ | |
456 | struct interrupt_data { | |
457 | u8 bType; | |
458 | u8 bValue; | |
459 | }; | |
460 | ||
461 | #define CBI_INTERRUPT_DATA_LEN 2 | |
462 | ||
463 | /* CBI Accept Device-Specific Command request */ | |
464 | #define USB_CBI_ADSC_REQUEST 0x00 | |
465 | ||
466 | ||
467 | #define MAX_COMMAND_SIZE 16 // Length of a SCSI Command Data Block | |
468 | ||
469 | /* SCSI commands that we recognize */ | |
470 | #define SC_FORMAT_UNIT 0x04 | |
471 | #define SC_INQUIRY 0x12 | |
472 | #define SC_MODE_SELECT_6 0x15 | |
473 | #define SC_MODE_SELECT_10 0x55 | |
474 | #define SC_MODE_SENSE_6 0x1a | |
475 | #define SC_MODE_SENSE_10 0x5a | |
476 | #define SC_PREVENT_ALLOW_MEDIUM_REMOVAL 0x1e | |
477 | #define SC_READ_6 0x08 | |
478 | #define SC_READ_10 0x28 | |
479 | #define SC_READ_12 0xa8 | |
480 | #define SC_READ_CAPACITY 0x25 | |
481 | #define SC_READ_FORMAT_CAPACITIES 0x23 | |
482 | #define SC_RELEASE 0x17 | |
483 | #define SC_REQUEST_SENSE 0x03 | |
484 | #define SC_RESERVE 0x16 | |
485 | #define SC_SEND_DIAGNOSTIC 0x1d | |
486 | #define SC_START_STOP_UNIT 0x1b | |
487 | #define SC_SYNCHRONIZE_CACHE 0x35 | |
488 | #define SC_TEST_UNIT_READY 0x00 | |
489 | #define SC_VERIFY 0x2f | |
490 | #define SC_WRITE_6 0x0a | |
491 | #define SC_WRITE_10 0x2a | |
492 | #define SC_WRITE_12 0xaa | |
493 | ||
494 | /* SCSI Sense Key/Additional Sense Code/ASC Qualifier values */ | |
495 | #define SS_NO_SENSE 0 | |
496 | #define SS_COMMUNICATION_FAILURE 0x040800 | |
497 | #define SS_INVALID_COMMAND 0x052000 | |
498 | #define SS_INVALID_FIELD_IN_CDB 0x052400 | |
499 | #define SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE 0x052100 | |
500 | #define SS_LOGICAL_UNIT_NOT_SUPPORTED 0x052500 | |
501 | #define SS_MEDIUM_NOT_PRESENT 0x023a00 | |
502 | #define SS_MEDIUM_REMOVAL_PREVENTED 0x055302 | |
503 | #define SS_NOT_READY_TO_READY_TRANSITION 0x062800 | |
504 | #define SS_RESET_OCCURRED 0x062900 | |
505 | #define SS_SAVING_PARAMETERS_NOT_SUPPORTED 0x053900 | |
506 | #define SS_UNRECOVERED_READ_ERROR 0x031100 | |
507 | #define SS_WRITE_ERROR 0x030c02 | |
508 | #define SS_WRITE_PROTECTED 0x072700 | |
509 | ||
510 | #define SK(x) ((u8) ((x) >> 16)) // Sense Key byte, etc. | |
511 | #define ASC(x) ((u8) ((x) >> 8)) | |
512 | #define ASCQ(x) ((u8) (x)) | |
513 | ||
514 | ||
515 | /*-------------------------------------------------------------------------*/ | |
516 | ||
517 | /* | |
518 | * These definitions will permit the compiler to avoid generating code for | |
519 | * parts of the driver that aren't used in the non-TEST version. Even gcc | |
520 | * can recognize when a test of a constant expression yields a dead code | |
521 | * path. | |
522 | */ | |
523 | ||
524 | #ifdef CONFIG_USB_FILE_STORAGE_TEST | |
525 | ||
526 | #define transport_is_bbb() (mod_data.transport_type == USB_PR_BULK) | |
527 | #define transport_is_cbi() (mod_data.transport_type == USB_PR_CBI) | |
528 | #define protocol_is_scsi() (mod_data.protocol_type == USB_SC_SCSI) | |
529 | ||
530 | #else | |
531 | ||
532 | #define transport_is_bbb() 1 | |
533 | #define transport_is_cbi() 0 | |
534 | #define protocol_is_scsi() 1 | |
535 | ||
536 | #endif /* CONFIG_USB_FILE_STORAGE_TEST */ | |
537 | ||
538 | ||
539 | struct lun { | |
540 | struct file *filp; | |
541 | loff_t file_length; | |
542 | loff_t num_sectors; | |
543 | ||
544 | unsigned int ro : 1; | |
545 | unsigned int prevent_medium_removal : 1; | |
546 | unsigned int registered : 1; | |
6174d0fd | 547 | unsigned int info_valid : 1; |
1da177e4 LT |
548 | |
549 | u32 sense_data; | |
550 | u32 sense_data_info; | |
551 | u32 unit_attention_data; | |
552 | ||
553 | struct device dev; | |
554 | }; | |
555 | ||
556 | #define backing_file_is_open(curlun) ((curlun)->filp != NULL) | |
557 | ||
79a7d9ee | 558 | static struct lun *dev_to_lun(struct device *dev) |
1da177e4 LT |
559 | { |
560 | return container_of(dev, struct lun, dev); | |
561 | } | |
562 | ||
563 | ||
564 | /* Big enough to hold our biggest descriptor */ | |
565 | #define EP0_BUFSIZE 256 | |
566 | #define DELAYED_STATUS (EP0_BUFSIZE + 999) // An impossibly large value | |
567 | ||
568 | /* Number of buffers we will use. 2 is enough for double-buffering */ | |
569 | #define NUM_BUFFERS 2 | |
570 | ||
571 | enum fsg_buffer_state { | |
572 | BUF_STATE_EMPTY = 0, | |
573 | BUF_STATE_FULL, | |
574 | BUF_STATE_BUSY | |
575 | }; | |
576 | ||
577 | struct fsg_buffhd { | |
578 | void *buf; | |
a21d4fed | 579 | enum fsg_buffer_state state; |
1da177e4 LT |
580 | struct fsg_buffhd *next; |
581 | ||
582 | /* The NetChip 2280 is faster, and handles some protocol faults | |
583 | * better, if we don't submit any short bulk-out read requests. | |
584 | * So we will record the intended request length here. */ | |
585 | unsigned int bulk_out_intended_length; | |
586 | ||
587 | struct usb_request *inreq; | |
a21d4fed | 588 | int inreq_busy; |
1da177e4 | 589 | struct usb_request *outreq; |
a21d4fed | 590 | int outreq_busy; |
1da177e4 LT |
591 | }; |
592 | ||
593 | enum fsg_state { | |
594 | FSG_STATE_COMMAND_PHASE = -10, // This one isn't used anywhere | |
595 | FSG_STATE_DATA_PHASE, | |
596 | FSG_STATE_STATUS_PHASE, | |
597 | ||
598 | FSG_STATE_IDLE = 0, | |
599 | FSG_STATE_ABORT_BULK_OUT, | |
600 | FSG_STATE_RESET, | |
601 | FSG_STATE_INTERFACE_CHANGE, | |
602 | FSG_STATE_CONFIG_CHANGE, | |
603 | FSG_STATE_DISCONNECT, | |
604 | FSG_STATE_EXIT, | |
605 | FSG_STATE_TERMINATED | |
606 | }; | |
607 | ||
608 | enum data_direction { | |
609 | DATA_DIR_UNKNOWN = 0, | |
610 | DATA_DIR_FROM_HOST, | |
611 | DATA_DIR_TO_HOST, | |
612 | DATA_DIR_NONE | |
613 | }; | |
614 | ||
615 | struct fsg_dev { | |
616 | /* lock protects: state, all the req_busy's, and cbbuf_cmnd */ | |
617 | spinlock_t lock; | |
618 | struct usb_gadget *gadget; | |
619 | ||
620 | /* filesem protects: backing files in use */ | |
621 | struct rw_semaphore filesem; | |
622 | ||
87c4252a AS |
623 | /* reference counting: wait until all LUNs are released */ |
624 | struct kref ref; | |
625 | ||
1da177e4 LT |
626 | struct usb_ep *ep0; // Handy copy of gadget->ep0 |
627 | struct usb_request *ep0req; // For control responses | |
a21d4fed | 628 | unsigned int ep0_req_tag; |
1da177e4 LT |
629 | const char *ep0req_name; |
630 | ||
631 | struct usb_request *intreq; // For interrupt responses | |
a21d4fed | 632 | int intreq_busy; |
1da177e4 LT |
633 | struct fsg_buffhd *intr_buffhd; |
634 | ||
635 | unsigned int bulk_out_maxpacket; | |
636 | enum fsg_state state; // For exception handling | |
637 | unsigned int exception_req_tag; | |
638 | ||
639 | u8 config, new_config; | |
640 | ||
641 | unsigned int running : 1; | |
642 | unsigned int bulk_in_enabled : 1; | |
643 | unsigned int bulk_out_enabled : 1; | |
644 | unsigned int intr_in_enabled : 1; | |
645 | unsigned int phase_error : 1; | |
646 | unsigned int short_packet_received : 1; | |
647 | unsigned int bad_lun_okay : 1; | |
648 | ||
649 | unsigned long atomic_bitflags; | |
650 | #define REGISTERED 0 | |
651 | #define CLEAR_BULK_HALTS 1 | |
652 | #define SUSPENDED 2 | |
653 | ||
654 | struct usb_ep *bulk_in; | |
655 | struct usb_ep *bulk_out; | |
656 | struct usb_ep *intr_in; | |
657 | ||
658 | struct fsg_buffhd *next_buffhd_to_fill; | |
659 | struct fsg_buffhd *next_buffhd_to_drain; | |
660 | struct fsg_buffhd buffhds[NUM_BUFFERS]; | |
661 | ||
1da177e4 LT |
662 | int thread_wakeup_needed; |
663 | struct completion thread_notifier; | |
1da177e4 | 664 | struct task_struct *thread_task; |
1da177e4 LT |
665 | |
666 | int cmnd_size; | |
667 | u8 cmnd[MAX_COMMAND_SIZE]; | |
668 | enum data_direction data_dir; | |
669 | u32 data_size; | |
670 | u32 data_size_from_cmnd; | |
671 | u32 tag; | |
672 | unsigned int lun; | |
673 | u32 residue; | |
674 | u32 usb_amount_left; | |
675 | ||
676 | /* The CB protocol offers no way for a host to know when a command | |
677 | * has completed. As a result the next command may arrive early, | |
678 | * and we will still have to handle it. For that reason we need | |
679 | * a buffer to store new commands when using CB (or CBI, which | |
680 | * does not oblige a host to wait for command completion either). */ | |
681 | int cbbuf_cmnd_size; | |
682 | u8 cbbuf_cmnd[MAX_COMMAND_SIZE]; | |
683 | ||
684 | unsigned int nluns; | |
685 | struct lun *luns; | |
686 | struct lun *curlun; | |
1da177e4 LT |
687 | }; |
688 | ||
689 | typedef void (*fsg_routine_t)(struct fsg_dev *); | |
690 | ||
79a7d9ee | 691 | static int exception_in_progress(struct fsg_dev *fsg) |
1da177e4 LT |
692 | { |
693 | return (fsg->state > FSG_STATE_IDLE); | |
694 | } | |
695 | ||
696 | /* Make bulk-out requests be divisible by the maxpacket size */ | |
79a7d9ee | 697 | static void set_bulk_out_req_length(struct fsg_dev *fsg, |
1da177e4 LT |
698 | struct fsg_buffhd *bh, unsigned int length) |
699 | { | |
700 | unsigned int rem; | |
701 | ||
702 | bh->bulk_out_intended_length = length; | |
703 | rem = length % fsg->bulk_out_maxpacket; | |
704 | if (rem > 0) | |
705 | length += fsg->bulk_out_maxpacket - rem; | |
706 | bh->outreq->length = length; | |
707 | } | |
708 | ||
709 | static struct fsg_dev *the_fsg; | |
710 | static struct usb_gadget_driver fsg_driver; | |
711 | ||
712 | static void close_backing_file(struct lun *curlun); | |
713 | static void close_all_backing_files(struct fsg_dev *fsg); | |
714 | ||
715 | ||
716 | /*-------------------------------------------------------------------------*/ | |
717 | ||
718 | #ifdef DUMP_MSGS | |
719 | ||
720 | static void dump_msg(struct fsg_dev *fsg, const char *label, | |
721 | const u8 *buf, unsigned int length) | |
722 | { | |
79a7d9ee AS |
723 | if (length < 512) { |
724 | DBG(fsg, "%s, length %u:\n", label, length); | |
725 | print_hex_dump(KERN_DEBUG, "", DUMP_PREFIX_OFFSET, | |
726 | 16, 1, buf, length, 0); | |
1da177e4 LT |
727 | } |
728 | } | |
729 | ||
79a7d9ee | 730 | static void dump_cdb(struct fsg_dev *fsg) |
1da177e4 LT |
731 | {} |
732 | ||
733 | #else | |
734 | ||
79a7d9ee | 735 | static void dump_msg(struct fsg_dev *fsg, const char *label, |
1da177e4 LT |
736 | const u8 *buf, unsigned int length) |
737 | {} | |
738 | ||
79a7d9ee | 739 | #ifdef VERBOSE_DEBUG |
1da177e4 | 740 | |
79a7d9ee AS |
741 | static void dump_cdb(struct fsg_dev *fsg) |
742 | { | |
743 | print_hex_dump(KERN_DEBUG, "SCSI CDB: ", DUMP_PREFIX_NONE, | |
744 | 16, 1, fsg->cmnd, fsg->cmnd_size, 0); | |
1da177e4 LT |
745 | } |
746 | ||
79a7d9ee AS |
747 | #else |
748 | ||
749 | static void dump_cdb(struct fsg_dev *fsg) | |
750 | {} | |
751 | ||
752 | #endif /* VERBOSE_DEBUG */ | |
1da177e4 LT |
753 | #endif /* DUMP_MSGS */ |
754 | ||
755 | ||
756 | static int fsg_set_halt(struct fsg_dev *fsg, struct usb_ep *ep) | |
757 | { | |
758 | const char *name; | |
759 | ||
760 | if (ep == fsg->bulk_in) | |
761 | name = "bulk-in"; | |
762 | else if (ep == fsg->bulk_out) | |
763 | name = "bulk-out"; | |
764 | else | |
765 | name = ep->name; | |
766 | DBG(fsg, "%s set halt\n", name); | |
767 | return usb_ep_set_halt(ep); | |
768 | } | |
769 | ||
770 | ||
771 | /*-------------------------------------------------------------------------*/ | |
772 | ||
773 | /* Routines for unaligned data access */ | |
774 | ||
79a7d9ee | 775 | static u16 get_be16(u8 *buf) |
1da177e4 LT |
776 | { |
777 | return ((u16) buf[0] << 8) | ((u16) buf[1]); | |
778 | } | |
779 | ||
79a7d9ee | 780 | static u32 get_be32(u8 *buf) |
1da177e4 LT |
781 | { |
782 | return ((u32) buf[0] << 24) | ((u32) buf[1] << 16) | | |
783 | ((u32) buf[2] << 8) | ((u32) buf[3]); | |
784 | } | |
785 | ||
79a7d9ee | 786 | static void put_be16(u8 *buf, u16 val) |
1da177e4 LT |
787 | { |
788 | buf[0] = val >> 8; | |
789 | buf[1] = val; | |
790 | } | |
791 | ||
79a7d9ee | 792 | static void put_be32(u8 *buf, u32 val) |
1da177e4 LT |
793 | { |
794 | buf[0] = val >> 24; | |
795 | buf[1] = val >> 16; | |
796 | buf[2] = val >> 8; | |
1bbc1696 | 797 | buf[3] = val & 0xff; |
1da177e4 LT |
798 | } |
799 | ||
800 | ||
801 | /*-------------------------------------------------------------------------*/ | |
802 | ||
803 | /* | |
804 | * DESCRIPTORS ... most are static, but strings and (full) configuration | |
805 | * descriptors are built on demand. Also the (static) config and interface | |
806 | * descriptors are adjusted during fsg_bind(). | |
807 | */ | |
808 | #define STRING_MANUFACTURER 1 | |
809 | #define STRING_PRODUCT 2 | |
810 | #define STRING_SERIAL 3 | |
811 | #define STRING_CONFIG 4 | |
812 | #define STRING_INTERFACE 5 | |
813 | ||
814 | /* There is only one configuration. */ | |
815 | #define CONFIG_VALUE 1 | |
816 | ||
817 | static struct usb_device_descriptor | |
818 | device_desc = { | |
819 | .bLength = sizeof device_desc, | |
820 | .bDescriptorType = USB_DT_DEVICE, | |
821 | ||
822 | .bcdUSB = __constant_cpu_to_le16(0x0200), | |
823 | .bDeviceClass = USB_CLASS_PER_INTERFACE, | |
824 | ||
825 | /* The next three values can be overridden by module parameters */ | |
826 | .idVendor = __constant_cpu_to_le16(DRIVER_VENDOR_ID), | |
827 | .idProduct = __constant_cpu_to_le16(DRIVER_PRODUCT_ID), | |
828 | .bcdDevice = __constant_cpu_to_le16(0xffff), | |
829 | ||
830 | .iManufacturer = STRING_MANUFACTURER, | |
831 | .iProduct = STRING_PRODUCT, | |
832 | .iSerialNumber = STRING_SERIAL, | |
833 | .bNumConfigurations = 1, | |
834 | }; | |
835 | ||
836 | static struct usb_config_descriptor | |
837 | config_desc = { | |
838 | .bLength = sizeof config_desc, | |
839 | .bDescriptorType = USB_DT_CONFIG, | |
840 | ||
841 | /* wTotalLength computed by usb_gadget_config_buf() */ | |
842 | .bNumInterfaces = 1, | |
843 | .bConfigurationValue = CONFIG_VALUE, | |
844 | .iConfiguration = STRING_CONFIG, | |
845 | .bmAttributes = USB_CONFIG_ATT_ONE | USB_CONFIG_ATT_SELFPOWER, | |
846 | .bMaxPower = 1, // self-powered | |
847 | }; | |
848 | ||
849 | static struct usb_otg_descriptor | |
850 | otg_desc = { | |
851 | .bLength = sizeof(otg_desc), | |
852 | .bDescriptorType = USB_DT_OTG, | |
853 | ||
854 | .bmAttributes = USB_OTG_SRP, | |
855 | }; | |
856 | ||
857 | /* There is only one interface. */ | |
858 | ||
859 | static struct usb_interface_descriptor | |
860 | intf_desc = { | |
861 | .bLength = sizeof intf_desc, | |
862 | .bDescriptorType = USB_DT_INTERFACE, | |
863 | ||
864 | .bNumEndpoints = 2, // Adjusted during fsg_bind() | |
865 | .bInterfaceClass = USB_CLASS_MASS_STORAGE, | |
866 | .bInterfaceSubClass = USB_SC_SCSI, // Adjusted during fsg_bind() | |
867 | .bInterfaceProtocol = USB_PR_BULK, // Adjusted during fsg_bind() | |
868 | .iInterface = STRING_INTERFACE, | |
869 | }; | |
870 | ||
871 | /* Three full-speed endpoint descriptors: bulk-in, bulk-out, | |
872 | * and interrupt-in. */ | |
873 | ||
874 | static struct usb_endpoint_descriptor | |
875 | fs_bulk_in_desc = { | |
876 | .bLength = USB_DT_ENDPOINT_SIZE, | |
877 | .bDescriptorType = USB_DT_ENDPOINT, | |
878 | ||
879 | .bEndpointAddress = USB_DIR_IN, | |
880 | .bmAttributes = USB_ENDPOINT_XFER_BULK, | |
881 | /* wMaxPacketSize set by autoconfiguration */ | |
882 | }; | |
883 | ||
884 | static struct usb_endpoint_descriptor | |
885 | fs_bulk_out_desc = { | |
886 | .bLength = USB_DT_ENDPOINT_SIZE, | |
887 | .bDescriptorType = USB_DT_ENDPOINT, | |
888 | ||
889 | .bEndpointAddress = USB_DIR_OUT, | |
890 | .bmAttributes = USB_ENDPOINT_XFER_BULK, | |
891 | /* wMaxPacketSize set by autoconfiguration */ | |
892 | }; | |
893 | ||
894 | static struct usb_endpoint_descriptor | |
895 | fs_intr_in_desc = { | |
896 | .bLength = USB_DT_ENDPOINT_SIZE, | |
897 | .bDescriptorType = USB_DT_ENDPOINT, | |
898 | ||
899 | .bEndpointAddress = USB_DIR_IN, | |
900 | .bmAttributes = USB_ENDPOINT_XFER_INT, | |
901 | .wMaxPacketSize = __constant_cpu_to_le16(2), | |
902 | .bInterval = 32, // frames -> 32 ms | |
903 | }; | |
904 | ||
905 | static const struct usb_descriptor_header *fs_function[] = { | |
906 | (struct usb_descriptor_header *) &otg_desc, | |
907 | (struct usb_descriptor_header *) &intf_desc, | |
908 | (struct usb_descriptor_header *) &fs_bulk_in_desc, | |
909 | (struct usb_descriptor_header *) &fs_bulk_out_desc, | |
910 | (struct usb_descriptor_header *) &fs_intr_in_desc, | |
911 | NULL, | |
912 | }; | |
913 | #define FS_FUNCTION_PRE_EP_ENTRIES 2 | |
914 | ||
915 | ||
1da177e4 LT |
916 | /* |
917 | * USB 2.0 devices need to expose both high speed and full speed | |
918 | * descriptors, unless they only run at full speed. | |
919 | * | |
920 | * That means alternate endpoint descriptors (bigger packets) | |
921 | * and a "device qualifier" ... plus more construction options | |
922 | * for the config descriptor. | |
923 | */ | |
924 | static struct usb_qualifier_descriptor | |
925 | dev_qualifier = { | |
926 | .bLength = sizeof dev_qualifier, | |
927 | .bDescriptorType = USB_DT_DEVICE_QUALIFIER, | |
928 | ||
929 | .bcdUSB = __constant_cpu_to_le16(0x0200), | |
930 | .bDeviceClass = USB_CLASS_PER_INTERFACE, | |
931 | ||
932 | .bNumConfigurations = 1, | |
933 | }; | |
934 | ||
935 | static struct usb_endpoint_descriptor | |
936 | hs_bulk_in_desc = { | |
937 | .bLength = USB_DT_ENDPOINT_SIZE, | |
938 | .bDescriptorType = USB_DT_ENDPOINT, | |
939 | ||
940 | /* bEndpointAddress copied from fs_bulk_in_desc during fsg_bind() */ | |
941 | .bmAttributes = USB_ENDPOINT_XFER_BULK, | |
942 | .wMaxPacketSize = __constant_cpu_to_le16(512), | |
943 | }; | |
944 | ||
945 | static struct usb_endpoint_descriptor | |
946 | hs_bulk_out_desc = { | |
947 | .bLength = USB_DT_ENDPOINT_SIZE, | |
948 | .bDescriptorType = USB_DT_ENDPOINT, | |
949 | ||
950 | /* bEndpointAddress copied from fs_bulk_out_desc during fsg_bind() */ | |
951 | .bmAttributes = USB_ENDPOINT_XFER_BULK, | |
952 | .wMaxPacketSize = __constant_cpu_to_le16(512), | |
953 | .bInterval = 1, // NAK every 1 uframe | |
954 | }; | |
955 | ||
956 | static struct usb_endpoint_descriptor | |
957 | hs_intr_in_desc = { | |
958 | .bLength = USB_DT_ENDPOINT_SIZE, | |
959 | .bDescriptorType = USB_DT_ENDPOINT, | |
960 | ||
961 | /* bEndpointAddress copied from fs_intr_in_desc during fsg_bind() */ | |
962 | .bmAttributes = USB_ENDPOINT_XFER_INT, | |
963 | .wMaxPacketSize = __constant_cpu_to_le16(2), | |
964 | .bInterval = 9, // 2**(9-1) = 256 uframes -> 32 ms | |
965 | }; | |
966 | ||
967 | static const struct usb_descriptor_header *hs_function[] = { | |
968 | (struct usb_descriptor_header *) &otg_desc, | |
969 | (struct usb_descriptor_header *) &intf_desc, | |
970 | (struct usb_descriptor_header *) &hs_bulk_in_desc, | |
971 | (struct usb_descriptor_header *) &hs_bulk_out_desc, | |
972 | (struct usb_descriptor_header *) &hs_intr_in_desc, | |
973 | NULL, | |
974 | }; | |
975 | #define HS_FUNCTION_PRE_EP_ENTRIES 2 | |
976 | ||
977 | /* Maxpacket and other transfer characteristics vary by speed. */ | |
79a7d9ee | 978 | static struct usb_endpoint_descriptor * |
2e806f67 DB |
979 | ep_desc(struct usb_gadget *g, struct usb_endpoint_descriptor *fs, |
980 | struct usb_endpoint_descriptor *hs) | |
981 | { | |
982 | if (gadget_is_dualspeed(g) && g->speed == USB_SPEED_HIGH) | |
983 | return hs; | |
984 | return fs; | |
985 | } | |
1da177e4 LT |
986 | |
987 | ||
988 | /* The CBI specification limits the serial string to 12 uppercase hexadecimal | |
989 | * characters. */ | |
990 | static char manufacturer[64]; | |
991 | static char serial[13]; | |
992 | ||
993 | /* Static strings, in UTF-8 (for simplicity we use only ASCII characters) */ | |
994 | static struct usb_string strings[] = { | |
995 | {STRING_MANUFACTURER, manufacturer}, | |
996 | {STRING_PRODUCT, longname}, | |
997 | {STRING_SERIAL, serial}, | |
998 | {STRING_CONFIG, "Self-powered"}, | |
999 | {STRING_INTERFACE, "Mass Storage"}, | |
1000 | {} | |
1001 | }; | |
1002 | ||
1003 | static struct usb_gadget_strings stringtab = { | |
1004 | .language = 0x0409, // en-us | |
1005 | .strings = strings, | |
1006 | }; | |
1007 | ||
1008 | ||
1009 | /* | |
1010 | * Config descriptors must agree with the code that sets configurations | |
1011 | * and with code managing interfaces and their altsettings. They must | |
1012 | * also handle different speeds and other-speed requests. | |
1013 | */ | |
1014 | static int populate_config_buf(struct usb_gadget *gadget, | |
1015 | u8 *buf, u8 type, unsigned index) | |
1016 | { | |
1da177e4 | 1017 | enum usb_device_speed speed = gadget->speed; |
1da177e4 LT |
1018 | int len; |
1019 | const struct usb_descriptor_header **function; | |
1020 | ||
1021 | if (index > 0) | |
1022 | return -EINVAL; | |
1023 | ||
2e806f67 | 1024 | if (gadget_is_dualspeed(gadget) && type == USB_DT_OTHER_SPEED_CONFIG) |
1da177e4 | 1025 | speed = (USB_SPEED_FULL + USB_SPEED_HIGH) - speed; |
2e806f67 | 1026 | if (gadget_is_dualspeed(gadget) && speed == USB_SPEED_HIGH) |
1da177e4 LT |
1027 | function = hs_function; |
1028 | else | |
1da177e4 LT |
1029 | function = fs_function; |
1030 | ||
1031 | /* for now, don't advertise srp-only devices */ | |
2e806f67 | 1032 | if (!gadget_is_otg(gadget)) |
1da177e4 LT |
1033 | function++; |
1034 | ||
1035 | len = usb_gadget_config_buf(&config_desc, buf, EP0_BUFSIZE, function); | |
1036 | ((struct usb_config_descriptor *) buf)->bDescriptorType = type; | |
1037 | return len; | |
1038 | } | |
1039 | ||
1040 | ||
1041 | /*-------------------------------------------------------------------------*/ | |
1042 | ||
1043 | /* These routines may be called in process context or in_irq */ | |
1044 | ||
a21d4fed | 1045 | /* Caller must hold fsg->lock */ |
1da177e4 LT |
1046 | static void wakeup_thread(struct fsg_dev *fsg) |
1047 | { | |
1048 | /* Tell the main thread that something has happened */ | |
1049 | fsg->thread_wakeup_needed = 1; | |
a21d4fed AS |
1050 | if (fsg->thread_task) |
1051 | wake_up_process(fsg->thread_task); | |
1da177e4 LT |
1052 | } |
1053 | ||
1054 | ||
1055 | static void raise_exception(struct fsg_dev *fsg, enum fsg_state new_state) | |
1056 | { | |
1057 | unsigned long flags; | |
1da177e4 LT |
1058 | |
1059 | /* Do nothing if a higher-priority exception is already in progress. | |
1060 | * If a lower-or-equal priority exception is in progress, preempt it | |
1061 | * and notify the main thread by sending it a signal. */ | |
1062 | spin_lock_irqsave(&fsg->lock, flags); | |
1063 | if (fsg->state <= new_state) { | |
1064 | fsg->exception_req_tag = fsg->ep0_req_tag; | |
1065 | fsg->state = new_state; | |
22efcf4a AS |
1066 | if (fsg->thread_task) |
1067 | send_sig_info(SIGUSR1, SEND_SIG_FORCED, | |
1068 | fsg->thread_task); | |
1da177e4 LT |
1069 | } |
1070 | spin_unlock_irqrestore(&fsg->lock, flags); | |
1071 | } | |
1072 | ||
1073 | ||
1074 | /*-------------------------------------------------------------------------*/ | |
1075 | ||
1076 | /* The disconnect callback and ep0 routines. These always run in_irq, | |
1077 | * except that ep0_queue() is called in the main thread to acknowledge | |
1078 | * completion of various requests: set config, set interface, and | |
1079 | * Bulk-only device reset. */ | |
1080 | ||
1081 | static void fsg_disconnect(struct usb_gadget *gadget) | |
1082 | { | |
1083 | struct fsg_dev *fsg = get_gadget_data(gadget); | |
1084 | ||
1085 | DBG(fsg, "disconnect or port reset\n"); | |
1086 | raise_exception(fsg, FSG_STATE_DISCONNECT); | |
1087 | } | |
1088 | ||
1089 | ||
1090 | static int ep0_queue(struct fsg_dev *fsg) | |
1091 | { | |
1092 | int rc; | |
1093 | ||
1094 | rc = usb_ep_queue(fsg->ep0, fsg->ep0req, GFP_ATOMIC); | |
1095 | if (rc != 0 && rc != -ESHUTDOWN) { | |
1096 | ||
1097 | /* We can't do much more than wait for a reset */ | |
1098 | WARN(fsg, "error in submission: %s --> %d\n", | |
1099 | fsg->ep0->name, rc); | |
1100 | } | |
1101 | return rc; | |
1102 | } | |
1103 | ||
1104 | static void ep0_complete(struct usb_ep *ep, struct usb_request *req) | |
1105 | { | |
7ca46b86 | 1106 | struct fsg_dev *fsg = ep->driver_data; |
1da177e4 LT |
1107 | |
1108 | if (req->actual > 0) | |
1109 | dump_msg(fsg, fsg->ep0req_name, req->buf, req->actual); | |
1110 | if (req->status || req->actual != req->length) | |
1111 | DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__, | |
1112 | req->status, req->actual, req->length); | |
1113 | if (req->status == -ECONNRESET) // Request was cancelled | |
1114 | usb_ep_fifo_flush(ep); | |
1115 | ||
1116 | if (req->status == 0 && req->context) | |
1117 | ((fsg_routine_t) (req->context))(fsg); | |
1118 | } | |
1119 | ||
1120 | ||
1121 | /*-------------------------------------------------------------------------*/ | |
1122 | ||
1123 | /* Bulk and interrupt endpoint completion handlers. | |
1124 | * These always run in_irq. */ | |
1125 | ||
1126 | static void bulk_in_complete(struct usb_ep *ep, struct usb_request *req) | |
1127 | { | |
7ca46b86 JD |
1128 | struct fsg_dev *fsg = ep->driver_data; |
1129 | struct fsg_buffhd *bh = req->context; | |
1da177e4 LT |
1130 | |
1131 | if (req->status || req->actual != req->length) | |
1132 | DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__, | |
1133 | req->status, req->actual, req->length); | |
1134 | if (req->status == -ECONNRESET) // Request was cancelled | |
1135 | usb_ep_fifo_flush(ep); | |
1136 | ||
1137 | /* Hold the lock while we update the request and buffer states */ | |
a21d4fed | 1138 | smp_wmb(); |
1da177e4 LT |
1139 | spin_lock(&fsg->lock); |
1140 | bh->inreq_busy = 0; | |
1141 | bh->state = BUF_STATE_EMPTY; | |
1da177e4 | 1142 | wakeup_thread(fsg); |
a21d4fed | 1143 | spin_unlock(&fsg->lock); |
1da177e4 LT |
1144 | } |
1145 | ||
1146 | static void bulk_out_complete(struct usb_ep *ep, struct usb_request *req) | |
1147 | { | |
7ca46b86 JD |
1148 | struct fsg_dev *fsg = ep->driver_data; |
1149 | struct fsg_buffhd *bh = req->context; | |
1da177e4 LT |
1150 | |
1151 | dump_msg(fsg, "bulk-out", req->buf, req->actual); | |
1152 | if (req->status || req->actual != bh->bulk_out_intended_length) | |
1153 | DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__, | |
1154 | req->status, req->actual, | |
1155 | bh->bulk_out_intended_length); | |
1156 | if (req->status == -ECONNRESET) // Request was cancelled | |
1157 | usb_ep_fifo_flush(ep); | |
1158 | ||
1159 | /* Hold the lock while we update the request and buffer states */ | |
a21d4fed | 1160 | smp_wmb(); |
1da177e4 LT |
1161 | spin_lock(&fsg->lock); |
1162 | bh->outreq_busy = 0; | |
1163 | bh->state = BUF_STATE_FULL; | |
1da177e4 | 1164 | wakeup_thread(fsg); |
a21d4fed | 1165 | spin_unlock(&fsg->lock); |
1da177e4 LT |
1166 | } |
1167 | ||
1168 | ||
1169 | #ifdef CONFIG_USB_FILE_STORAGE_TEST | |
1170 | static void intr_in_complete(struct usb_ep *ep, struct usb_request *req) | |
1171 | { | |
7ca46b86 JD |
1172 | struct fsg_dev *fsg = ep->driver_data; |
1173 | struct fsg_buffhd *bh = req->context; | |
1da177e4 LT |
1174 | |
1175 | if (req->status || req->actual != req->length) | |
1176 | DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__, | |
1177 | req->status, req->actual, req->length); | |
1178 | if (req->status == -ECONNRESET) // Request was cancelled | |
1179 | usb_ep_fifo_flush(ep); | |
1180 | ||
1181 | /* Hold the lock while we update the request and buffer states */ | |
a21d4fed | 1182 | smp_wmb(); |
1da177e4 LT |
1183 | spin_lock(&fsg->lock); |
1184 | fsg->intreq_busy = 0; | |
1185 | bh->state = BUF_STATE_EMPTY; | |
1da177e4 | 1186 | wakeup_thread(fsg); |
a21d4fed | 1187 | spin_unlock(&fsg->lock); |
1da177e4 LT |
1188 | } |
1189 | ||
1190 | #else | |
1191 | static void intr_in_complete(struct usb_ep *ep, struct usb_request *req) | |
1192 | {} | |
1193 | #endif /* CONFIG_USB_FILE_STORAGE_TEST */ | |
1194 | ||
1195 | ||
1196 | /*-------------------------------------------------------------------------*/ | |
1197 | ||
1198 | /* Ep0 class-specific handlers. These always run in_irq. */ | |
1199 | ||
1200 | #ifdef CONFIG_USB_FILE_STORAGE_TEST | |
1201 | static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh) | |
1202 | { | |
1203 | struct usb_request *req = fsg->ep0req; | |
1204 | static u8 cbi_reset_cmnd[6] = { | |
1205 | SC_SEND_DIAGNOSTIC, 4, 0xff, 0xff, 0xff, 0xff}; | |
1206 | ||
1207 | /* Error in command transfer? */ | |
1208 | if (req->status || req->length != req->actual || | |
1209 | req->actual < 6 || req->actual > MAX_COMMAND_SIZE) { | |
1210 | ||
1211 | /* Not all controllers allow a protocol stall after | |
1212 | * receiving control-out data, but we'll try anyway. */ | |
1213 | fsg_set_halt(fsg, fsg->ep0); | |
1214 | return; // Wait for reset | |
1215 | } | |
1216 | ||
1217 | /* Is it the special reset command? */ | |
1218 | if (req->actual >= sizeof cbi_reset_cmnd && | |
1219 | memcmp(req->buf, cbi_reset_cmnd, | |
1220 | sizeof cbi_reset_cmnd) == 0) { | |
1221 | ||
1222 | /* Raise an exception to stop the current operation | |
1223 | * and reinitialize our state. */ | |
1224 | DBG(fsg, "cbi reset request\n"); | |
1225 | raise_exception(fsg, FSG_STATE_RESET); | |
1226 | return; | |
1227 | } | |
1228 | ||
1229 | VDBG(fsg, "CB[I] accept device-specific command\n"); | |
1230 | spin_lock(&fsg->lock); | |
1231 | ||
1232 | /* Save the command for later */ | |
1233 | if (fsg->cbbuf_cmnd_size) | |
1234 | WARN(fsg, "CB[I] overwriting previous command\n"); | |
1235 | fsg->cbbuf_cmnd_size = req->actual; | |
1236 | memcpy(fsg->cbbuf_cmnd, req->buf, fsg->cbbuf_cmnd_size); | |
1237 | ||
1da177e4 | 1238 | wakeup_thread(fsg); |
a21d4fed | 1239 | spin_unlock(&fsg->lock); |
1da177e4 LT |
1240 | } |
1241 | ||
1242 | #else | |
1243 | static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh) | |
1244 | {} | |
1245 | #endif /* CONFIG_USB_FILE_STORAGE_TEST */ | |
1246 | ||
1247 | ||
1248 | static int class_setup_req(struct fsg_dev *fsg, | |
1249 | const struct usb_ctrlrequest *ctrl) | |
1250 | { | |
1251 | struct usb_request *req = fsg->ep0req; | |
1252 | int value = -EOPNOTSUPP; | |
1bbc1696 | 1253 | u16 w_index = le16_to_cpu(ctrl->wIndex); |
88e45dbb | 1254 | u16 w_value = le16_to_cpu(ctrl->wValue); |
1bbc1696 | 1255 | u16 w_length = le16_to_cpu(ctrl->wLength); |
1da177e4 LT |
1256 | |
1257 | if (!fsg->config) | |
1258 | return value; | |
1259 | ||
1260 | /* Handle Bulk-only class-specific requests */ | |
1261 | if (transport_is_bbb()) { | |
1262 | switch (ctrl->bRequest) { | |
1263 | ||
1264 | case USB_BULK_RESET_REQUEST: | |
1265 | if (ctrl->bRequestType != (USB_DIR_OUT | | |
1266 | USB_TYPE_CLASS | USB_RECIP_INTERFACE)) | |
1267 | break; | |
88e45dbb | 1268 | if (w_index != 0 || w_value != 0) { |
1da177e4 LT |
1269 | value = -EDOM; |
1270 | break; | |
1271 | } | |
1272 | ||
1273 | /* Raise an exception to stop the current operation | |
1274 | * and reinitialize our state. */ | |
1275 | DBG(fsg, "bulk reset request\n"); | |
1276 | raise_exception(fsg, FSG_STATE_RESET); | |
1277 | value = DELAYED_STATUS; | |
1278 | break; | |
1279 | ||
1280 | case USB_BULK_GET_MAX_LUN_REQUEST: | |
1281 | if (ctrl->bRequestType != (USB_DIR_IN | | |
1282 | USB_TYPE_CLASS | USB_RECIP_INTERFACE)) | |
1283 | break; | |
88e45dbb | 1284 | if (w_index != 0 || w_value != 0) { |
1da177e4 LT |
1285 | value = -EDOM; |
1286 | break; | |
1287 | } | |
1288 | VDBG(fsg, "get max LUN\n"); | |
1289 | *(u8 *) req->buf = fsg->nluns - 1; | |
76f4af8e | 1290 | value = 1; |
1da177e4 LT |
1291 | break; |
1292 | } | |
1293 | } | |
1294 | ||
1295 | /* Handle CBI class-specific requests */ | |
1296 | else { | |
1297 | switch (ctrl->bRequest) { | |
1298 | ||
1299 | case USB_CBI_ADSC_REQUEST: | |
1300 | if (ctrl->bRequestType != (USB_DIR_OUT | | |
1301 | USB_TYPE_CLASS | USB_RECIP_INTERFACE)) | |
1302 | break; | |
88e45dbb | 1303 | if (w_index != 0 || w_value != 0) { |
1da177e4 LT |
1304 | value = -EDOM; |
1305 | break; | |
1306 | } | |
1307 | if (w_length > MAX_COMMAND_SIZE) { | |
1308 | value = -EOVERFLOW; | |
1309 | break; | |
1310 | } | |
1311 | value = w_length; | |
1312 | fsg->ep0req->context = received_cbi_adsc; | |
1313 | break; | |
1314 | } | |
1315 | } | |
1316 | ||
1317 | if (value == -EOPNOTSUPP) | |
1318 | VDBG(fsg, | |
1319 | "unknown class-specific control req " | |
1320 | "%02x.%02x v%04x i%04x l%u\n", | |
1321 | ctrl->bRequestType, ctrl->bRequest, | |
1bbc1696 | 1322 | le16_to_cpu(ctrl->wValue), w_index, w_length); |
1da177e4 LT |
1323 | return value; |
1324 | } | |
1325 | ||
1326 | ||
1327 | /*-------------------------------------------------------------------------*/ | |
1328 | ||
1329 | /* Ep0 standard request handlers. These always run in_irq. */ | |
1330 | ||
1331 | static int standard_setup_req(struct fsg_dev *fsg, | |
1332 | const struct usb_ctrlrequest *ctrl) | |
1333 | { | |
1334 | struct usb_request *req = fsg->ep0req; | |
1335 | int value = -EOPNOTSUPP; | |
1bbc1696 DB |
1336 | u16 w_index = le16_to_cpu(ctrl->wIndex); |
1337 | u16 w_value = le16_to_cpu(ctrl->wValue); | |
1da177e4 LT |
1338 | |
1339 | /* Usually this just stores reply data in the pre-allocated ep0 buffer, | |
1340 | * but config change events will also reconfigure hardware. */ | |
1341 | switch (ctrl->bRequest) { | |
1342 | ||
1343 | case USB_REQ_GET_DESCRIPTOR: | |
1344 | if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD | | |
1345 | USB_RECIP_DEVICE)) | |
1346 | break; | |
1347 | switch (w_value >> 8) { | |
1348 | ||
1349 | case USB_DT_DEVICE: | |
1350 | VDBG(fsg, "get device descriptor\n"); | |
76f4af8e | 1351 | value = sizeof device_desc; |
1da177e4 LT |
1352 | memcpy(req->buf, &device_desc, value); |
1353 | break; | |
1da177e4 LT |
1354 | case USB_DT_DEVICE_QUALIFIER: |
1355 | VDBG(fsg, "get device qualifier\n"); | |
2e806f67 | 1356 | if (!gadget_is_dualspeed(fsg->gadget)) |
1da177e4 | 1357 | break; |
76f4af8e | 1358 | value = sizeof dev_qualifier; |
1da177e4 LT |
1359 | memcpy(req->buf, &dev_qualifier, value); |
1360 | break; | |
1361 | ||
1362 | case USB_DT_OTHER_SPEED_CONFIG: | |
1363 | VDBG(fsg, "get other-speed config descriptor\n"); | |
2e806f67 | 1364 | if (!gadget_is_dualspeed(fsg->gadget)) |
1da177e4 LT |
1365 | break; |
1366 | goto get_config; | |
1da177e4 LT |
1367 | case USB_DT_CONFIG: |
1368 | VDBG(fsg, "get configuration descriptor\n"); | |
2e806f67 | 1369 | get_config: |
1da177e4 LT |
1370 | value = populate_config_buf(fsg->gadget, |
1371 | req->buf, | |
1372 | w_value >> 8, | |
1373 | w_value & 0xff); | |
1da177e4 LT |
1374 | break; |
1375 | ||
1376 | case USB_DT_STRING: | |
1377 | VDBG(fsg, "get string descriptor\n"); | |
1378 | ||
1379 | /* wIndex == language code */ | |
1380 | value = usb_gadget_get_string(&stringtab, | |
1381 | w_value & 0xff, req->buf); | |
1da177e4 LT |
1382 | break; |
1383 | } | |
1384 | break; | |
1385 | ||
1386 | /* One config, two speeds */ | |
1387 | case USB_REQ_SET_CONFIGURATION: | |
1388 | if (ctrl->bRequestType != (USB_DIR_OUT | USB_TYPE_STANDARD | | |
1389 | USB_RECIP_DEVICE)) | |
1390 | break; | |
1391 | VDBG(fsg, "set configuration\n"); | |
1392 | if (w_value == CONFIG_VALUE || w_value == 0) { | |
1393 | fsg->new_config = w_value; | |
1394 | ||
1395 | /* Raise an exception to wipe out previous transaction | |
1396 | * state (queued bufs, etc) and set the new config. */ | |
1397 | raise_exception(fsg, FSG_STATE_CONFIG_CHANGE); | |
1398 | value = DELAYED_STATUS; | |
1399 | } | |
1400 | break; | |
1401 | case USB_REQ_GET_CONFIGURATION: | |
1402 | if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD | | |
1403 | USB_RECIP_DEVICE)) | |
1404 | break; | |
1405 | VDBG(fsg, "get configuration\n"); | |
1406 | *(u8 *) req->buf = fsg->config; | |
76f4af8e | 1407 | value = 1; |
1da177e4 LT |
1408 | break; |
1409 | ||
1410 | case USB_REQ_SET_INTERFACE: | |
1411 | if (ctrl->bRequestType != (USB_DIR_OUT| USB_TYPE_STANDARD | | |
1412 | USB_RECIP_INTERFACE)) | |
1413 | break; | |
1414 | if (fsg->config && w_index == 0) { | |
1415 | ||
1416 | /* Raise an exception to wipe out previous transaction | |
1417 | * state (queued bufs, etc) and install the new | |
1418 | * interface altsetting. */ | |
1419 | raise_exception(fsg, FSG_STATE_INTERFACE_CHANGE); | |
1420 | value = DELAYED_STATUS; | |
1421 | } | |
1422 | break; | |
1423 | case USB_REQ_GET_INTERFACE: | |
1424 | if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD | | |
1425 | USB_RECIP_INTERFACE)) | |
1426 | break; | |
1427 | if (!fsg->config) | |
1428 | break; | |
1429 | if (w_index != 0) { | |
1430 | value = -EDOM; | |
1431 | break; | |
1432 | } | |
1433 | VDBG(fsg, "get interface\n"); | |
1434 | *(u8 *) req->buf = 0; | |
76f4af8e | 1435 | value = 1; |
1da177e4 LT |
1436 | break; |
1437 | ||
1438 | default: | |
1439 | VDBG(fsg, | |
1440 | "unknown control req %02x.%02x v%04x i%04x l%u\n", | |
1441 | ctrl->bRequestType, ctrl->bRequest, | |
1bbc1696 | 1442 | w_value, w_index, le16_to_cpu(ctrl->wLength)); |
1da177e4 LT |
1443 | } |
1444 | ||
1445 | return value; | |
1446 | } | |
1447 | ||
1448 | ||
1449 | static int fsg_setup(struct usb_gadget *gadget, | |
1450 | const struct usb_ctrlrequest *ctrl) | |
1451 | { | |
1452 | struct fsg_dev *fsg = get_gadget_data(gadget); | |
1453 | int rc; | |
1bbc1696 | 1454 | int w_length = le16_to_cpu(ctrl->wLength); |
1da177e4 LT |
1455 | |
1456 | ++fsg->ep0_req_tag; // Record arrival of a new request | |
1457 | fsg->ep0req->context = NULL; | |
1458 | fsg->ep0req->length = 0; | |
1459 | dump_msg(fsg, "ep0-setup", (u8 *) ctrl, sizeof(*ctrl)); | |
1460 | ||
1461 | if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_CLASS) | |
1462 | rc = class_setup_req(fsg, ctrl); | |
1463 | else | |
1464 | rc = standard_setup_req(fsg, ctrl); | |
1465 | ||
1466 | /* Respond with data/status or defer until later? */ | |
1467 | if (rc >= 0 && rc != DELAYED_STATUS) { | |
76f4af8e | 1468 | rc = min(rc, w_length); |
1da177e4 | 1469 | fsg->ep0req->length = rc; |
1bbc1696 | 1470 | fsg->ep0req->zero = rc < w_length; |
1da177e4 LT |
1471 | fsg->ep0req_name = (ctrl->bRequestType & USB_DIR_IN ? |
1472 | "ep0-in" : "ep0-out"); | |
1473 | rc = ep0_queue(fsg); | |
1474 | } | |
1475 | ||
1476 | /* Device either stalls (rc < 0) or reports success */ | |
1477 | return rc; | |
1478 | } | |
1479 | ||
1480 | ||
1481 | /*-------------------------------------------------------------------------*/ | |
1482 | ||
1483 | /* All the following routines run in process context */ | |
1484 | ||
1485 | ||
1486 | /* Use this for bulk or interrupt transfers, not ep0 */ | |
1487 | static void start_transfer(struct fsg_dev *fsg, struct usb_ep *ep, | |
a21d4fed AS |
1488 | struct usb_request *req, int *pbusy, |
1489 | enum fsg_buffer_state *state) | |
1da177e4 LT |
1490 | { |
1491 | int rc; | |
1492 | ||
1493 | if (ep == fsg->bulk_in) | |
1494 | dump_msg(fsg, "bulk-in", req->buf, req->length); | |
1495 | else if (ep == fsg->intr_in) | |
1496 | dump_msg(fsg, "intr-in", req->buf, req->length); | |
a21d4fed AS |
1497 | |
1498 | spin_lock_irq(&fsg->lock); | |
1da177e4 LT |
1499 | *pbusy = 1; |
1500 | *state = BUF_STATE_BUSY; | |
a21d4fed | 1501 | spin_unlock_irq(&fsg->lock); |
1da177e4 LT |
1502 | rc = usb_ep_queue(ep, req, GFP_KERNEL); |
1503 | if (rc != 0) { | |
1504 | *pbusy = 0; | |
1505 | *state = BUF_STATE_EMPTY; | |
1506 | ||
1507 | /* We can't do much more than wait for a reset */ | |
1508 | ||
1509 | /* Note: currently the net2280 driver fails zero-length | |
1510 | * submissions if DMA is enabled. */ | |
1511 | if (rc != -ESHUTDOWN && !(rc == -EOPNOTSUPP && | |
1512 | req->length == 0)) | |
1513 | WARN(fsg, "error in submission: %s --> %d\n", | |
1514 | ep->name, rc); | |
1515 | } | |
1516 | } | |
1517 | ||
1518 | ||
1519 | static int sleep_thread(struct fsg_dev *fsg) | |
1520 | { | |
a21d4fed | 1521 | int rc = 0; |
1da177e4 LT |
1522 | |
1523 | /* Wait until a signal arrives or we are woken up */ | |
a21d4fed AS |
1524 | for (;;) { |
1525 | try_to_freeze(); | |
1526 | set_current_state(TASK_INTERRUPTIBLE); | |
1527 | if (signal_pending(current)) { | |
1528 | rc = -EINTR; | |
1529 | break; | |
1530 | } | |
1531 | if (fsg->thread_wakeup_needed) | |
1532 | break; | |
1533 | schedule(); | |
1534 | } | |
1535 | __set_current_state(TASK_RUNNING); | |
1da177e4 | 1536 | fsg->thread_wakeup_needed = 0; |
a21d4fed | 1537 | return rc; |
1da177e4 LT |
1538 | } |
1539 | ||
1540 | ||
1541 | /*-------------------------------------------------------------------------*/ | |
1542 | ||
1543 | static int do_read(struct fsg_dev *fsg) | |
1544 | { | |
1545 | struct lun *curlun = fsg->curlun; | |
1546 | u32 lba; | |
1547 | struct fsg_buffhd *bh; | |
1548 | int rc; | |
1549 | u32 amount_left; | |
1550 | loff_t file_offset, file_offset_tmp; | |
1551 | unsigned int amount; | |
1552 | unsigned int partial_page; | |
1553 | ssize_t nread; | |
1554 | ||
1555 | /* Get the starting Logical Block Address and check that it's | |
1556 | * not too big */ | |
1557 | if (fsg->cmnd[0] == SC_READ_6) | |
1558 | lba = (fsg->cmnd[1] << 16) | get_be16(&fsg->cmnd[2]); | |
1559 | else { | |
1560 | lba = get_be32(&fsg->cmnd[2]); | |
1561 | ||
1562 | /* We allow DPO (Disable Page Out = don't save data in the | |
1563 | * cache) and FUA (Force Unit Access = don't read from the | |
1564 | * cache), but we don't implement them. */ | |
1565 | if ((fsg->cmnd[1] & ~0x18) != 0) { | |
1566 | curlun->sense_data = SS_INVALID_FIELD_IN_CDB; | |
1567 | return -EINVAL; | |
1568 | } | |
1569 | } | |
1570 | if (lba >= curlun->num_sectors) { | |
1571 | curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; | |
1572 | return -EINVAL; | |
1573 | } | |
1574 | file_offset = ((loff_t) lba) << 9; | |
1575 | ||
1576 | /* Carry out the file reads */ | |
1577 | amount_left = fsg->data_size_from_cmnd; | |
1578 | if (unlikely(amount_left == 0)) | |
1579 | return -EIO; // No default reply | |
1580 | ||
1581 | for (;;) { | |
1582 | ||
1583 | /* Figure out how much we need to read: | |
1584 | * Try to read the remaining amount. | |
1585 | * But don't read more than the buffer size. | |
1586 | * And don't try to read past the end of the file. | |
1587 | * Finally, if we're not at a page boundary, don't read past | |
1588 | * the next page. | |
1589 | * If this means reading 0 then we were asked to read past | |
1590 | * the end of file. */ | |
1591 | amount = min((unsigned int) amount_left, mod_data.buflen); | |
1592 | amount = min((loff_t) amount, | |
1593 | curlun->file_length - file_offset); | |
1594 | partial_page = file_offset & (PAGE_CACHE_SIZE - 1); | |
1595 | if (partial_page > 0) | |
1596 | amount = min(amount, (unsigned int) PAGE_CACHE_SIZE - | |
1597 | partial_page); | |
1598 | ||
1599 | /* Wait for the next buffer to become available */ | |
1600 | bh = fsg->next_buffhd_to_fill; | |
1601 | while (bh->state != BUF_STATE_EMPTY) { | |
79a7d9ee AS |
1602 | rc = sleep_thread(fsg); |
1603 | if (rc) | |
1da177e4 LT |
1604 | return rc; |
1605 | } | |
1606 | ||
1607 | /* If we were asked to read past the end of file, | |
1608 | * end with an empty buffer. */ | |
1609 | if (amount == 0) { | |
1610 | curlun->sense_data = | |
1611 | SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; | |
1612 | curlun->sense_data_info = file_offset >> 9; | |
6174d0fd | 1613 | curlun->info_valid = 1; |
1da177e4 LT |
1614 | bh->inreq->length = 0; |
1615 | bh->state = BUF_STATE_FULL; | |
1616 | break; | |
1617 | } | |
1618 | ||
1619 | /* Perform the read */ | |
1620 | file_offset_tmp = file_offset; | |
1621 | nread = vfs_read(curlun->filp, | |
1622 | (char __user *) bh->buf, | |
1623 | amount, &file_offset_tmp); | |
1624 | VLDBG(curlun, "file read %u @ %llu -> %d\n", amount, | |
1625 | (unsigned long long) file_offset, | |
1626 | (int) nread); | |
1627 | if (signal_pending(current)) | |
1628 | return -EINTR; | |
1629 | ||
1630 | if (nread < 0) { | |
1631 | LDBG(curlun, "error in file read: %d\n", | |
1632 | (int) nread); | |
1633 | nread = 0; | |
1634 | } else if (nread < amount) { | |
1635 | LDBG(curlun, "partial file read: %d/%u\n", | |
1636 | (int) nread, amount); | |
1637 | nread -= (nread & 511); // Round down to a block | |
1638 | } | |
1639 | file_offset += nread; | |
1640 | amount_left -= nread; | |
1641 | fsg->residue -= nread; | |
1642 | bh->inreq->length = nread; | |
1643 | bh->state = BUF_STATE_FULL; | |
1644 | ||
1645 | /* If an error occurred, report it and its position */ | |
1646 | if (nread < amount) { | |
1647 | curlun->sense_data = SS_UNRECOVERED_READ_ERROR; | |
1648 | curlun->sense_data_info = file_offset >> 9; | |
6174d0fd | 1649 | curlun->info_valid = 1; |
1da177e4 LT |
1650 | break; |
1651 | } | |
1652 | ||
1653 | if (amount_left == 0) | |
1654 | break; // No more left to read | |
1655 | ||
1656 | /* Send this buffer and go read some more */ | |
1657 | bh->inreq->zero = 0; | |
1658 | start_transfer(fsg, fsg->bulk_in, bh->inreq, | |
1659 | &bh->inreq_busy, &bh->state); | |
1660 | fsg->next_buffhd_to_fill = bh->next; | |
1661 | } | |
1662 | ||
1663 | return -EIO; // No default reply | |
1664 | } | |
1665 | ||
1666 | ||
1667 | /*-------------------------------------------------------------------------*/ | |
1668 | ||
1669 | static int do_write(struct fsg_dev *fsg) | |
1670 | { | |
1671 | struct lun *curlun = fsg->curlun; | |
1672 | u32 lba; | |
1673 | struct fsg_buffhd *bh; | |
1674 | int get_some_more; | |
1675 | u32 amount_left_to_req, amount_left_to_write; | |
1676 | loff_t usb_offset, file_offset, file_offset_tmp; | |
1677 | unsigned int amount; | |
1678 | unsigned int partial_page; | |
1679 | ssize_t nwritten; | |
1680 | int rc; | |
1681 | ||
1682 | if (curlun->ro) { | |
1683 | curlun->sense_data = SS_WRITE_PROTECTED; | |
1684 | return -EINVAL; | |
1685 | } | |
1686 | curlun->filp->f_flags &= ~O_SYNC; // Default is not to wait | |
1687 | ||
1688 | /* Get the starting Logical Block Address and check that it's | |
1689 | * not too big */ | |
1690 | if (fsg->cmnd[0] == SC_WRITE_6) | |
1691 | lba = (fsg->cmnd[1] << 16) | get_be16(&fsg->cmnd[2]); | |
1692 | else { | |
1693 | lba = get_be32(&fsg->cmnd[2]); | |
1694 | ||
1695 | /* We allow DPO (Disable Page Out = don't save data in the | |
1696 | * cache) and FUA (Force Unit Access = write directly to the | |
1697 | * medium). We don't implement DPO; we implement FUA by | |
1698 | * performing synchronous output. */ | |
1699 | if ((fsg->cmnd[1] & ~0x18) != 0) { | |
1700 | curlun->sense_data = SS_INVALID_FIELD_IN_CDB; | |
1701 | return -EINVAL; | |
1702 | } | |
1703 | if (fsg->cmnd[1] & 0x08) // FUA | |
1704 | curlun->filp->f_flags |= O_SYNC; | |
1705 | } | |
1706 | if (lba >= curlun->num_sectors) { | |
1707 | curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; | |
1708 | return -EINVAL; | |
1709 | } | |
1710 | ||
1711 | /* Carry out the file writes */ | |
1712 | get_some_more = 1; | |
1713 | file_offset = usb_offset = ((loff_t) lba) << 9; | |
1714 | amount_left_to_req = amount_left_to_write = fsg->data_size_from_cmnd; | |
1715 | ||
1716 | while (amount_left_to_write > 0) { | |
1717 | ||
1718 | /* Queue a request for more data from the host */ | |
1719 | bh = fsg->next_buffhd_to_fill; | |
1720 | if (bh->state == BUF_STATE_EMPTY && get_some_more) { | |
1721 | ||
1722 | /* Figure out how much we want to get: | |
1723 | * Try to get the remaining amount. | |
1724 | * But don't get more than the buffer size. | |
1725 | * And don't try to go past the end of the file. | |
1726 | * If we're not at a page boundary, | |
1727 | * don't go past the next page. | |
1728 | * If this means getting 0, then we were asked | |
1729 | * to write past the end of file. | |
1730 | * Finally, round down to a block boundary. */ | |
1731 | amount = min(amount_left_to_req, mod_data.buflen); | |
1732 | amount = min((loff_t) amount, curlun->file_length - | |
1733 | usb_offset); | |
1734 | partial_page = usb_offset & (PAGE_CACHE_SIZE - 1); | |
1735 | if (partial_page > 0) | |
1736 | amount = min(amount, | |
1737 | (unsigned int) PAGE_CACHE_SIZE - partial_page); | |
1738 | ||
1739 | if (amount == 0) { | |
1740 | get_some_more = 0; | |
1741 | curlun->sense_data = | |
1742 | SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; | |
1743 | curlun->sense_data_info = usb_offset >> 9; | |
6174d0fd | 1744 | curlun->info_valid = 1; |
1da177e4 LT |
1745 | continue; |
1746 | } | |
1747 | amount -= (amount & 511); | |
1748 | if (amount == 0) { | |
1749 | ||
1750 | /* Why were we were asked to transfer a | |
1751 | * partial block? */ | |
1752 | get_some_more = 0; | |
1753 | continue; | |
1754 | } | |
1755 | ||
1756 | /* Get the next buffer */ | |
1757 | usb_offset += amount; | |
1758 | fsg->usb_amount_left -= amount; | |
1759 | amount_left_to_req -= amount; | |
1760 | if (amount_left_to_req == 0) | |
1761 | get_some_more = 0; | |
1762 | ||
1763 | /* amount is always divisible by 512, hence by | |
1764 | * the bulk-out maxpacket size */ | |
1765 | bh->outreq->length = bh->bulk_out_intended_length = | |
1766 | amount; | |
70ffe6e1 | 1767 | bh->outreq->short_not_ok = 1; |
1da177e4 LT |
1768 | start_transfer(fsg, fsg->bulk_out, bh->outreq, |
1769 | &bh->outreq_busy, &bh->state); | |
1770 | fsg->next_buffhd_to_fill = bh->next; | |
1771 | continue; | |
1772 | } | |
1773 | ||
1774 | /* Write the received data to the backing file */ | |
1775 | bh = fsg->next_buffhd_to_drain; | |
1776 | if (bh->state == BUF_STATE_EMPTY && !get_some_more) | |
1777 | break; // We stopped early | |
1778 | if (bh->state == BUF_STATE_FULL) { | |
a21d4fed | 1779 | smp_rmb(); |
1da177e4 LT |
1780 | fsg->next_buffhd_to_drain = bh->next; |
1781 | bh->state = BUF_STATE_EMPTY; | |
1782 | ||
1783 | /* Did something go wrong with the transfer? */ | |
1784 | if (bh->outreq->status != 0) { | |
1785 | curlun->sense_data = SS_COMMUNICATION_FAILURE; | |
1786 | curlun->sense_data_info = file_offset >> 9; | |
6174d0fd | 1787 | curlun->info_valid = 1; |
1da177e4 LT |
1788 | break; |
1789 | } | |
1790 | ||
1791 | amount = bh->outreq->actual; | |
1792 | if (curlun->file_length - file_offset < amount) { | |
1793 | LERROR(curlun, | |
1794 | "write %u @ %llu beyond end %llu\n", | |
1795 | amount, (unsigned long long) file_offset, | |
1796 | (unsigned long long) curlun->file_length); | |
1797 | amount = curlun->file_length - file_offset; | |
1798 | } | |
1799 | ||
1800 | /* Perform the write */ | |
1801 | file_offset_tmp = file_offset; | |
1802 | nwritten = vfs_write(curlun->filp, | |
1803 | (char __user *) bh->buf, | |
1804 | amount, &file_offset_tmp); | |
1805 | VLDBG(curlun, "file write %u @ %llu -> %d\n", amount, | |
1806 | (unsigned long long) file_offset, | |
1807 | (int) nwritten); | |
1808 | if (signal_pending(current)) | |
1809 | return -EINTR; // Interrupted! | |
1810 | ||
1811 | if (nwritten < 0) { | |
1812 | LDBG(curlun, "error in file write: %d\n", | |
1813 | (int) nwritten); | |
1814 | nwritten = 0; | |
1815 | } else if (nwritten < amount) { | |
1816 | LDBG(curlun, "partial file write: %d/%u\n", | |
1817 | (int) nwritten, amount); | |
1818 | nwritten -= (nwritten & 511); | |
1819 | // Round down to a block | |
1820 | } | |
1821 | file_offset += nwritten; | |
1822 | amount_left_to_write -= nwritten; | |
1823 | fsg->residue -= nwritten; | |
1824 | ||
1825 | /* If an error occurred, report it and its position */ | |
1826 | if (nwritten < amount) { | |
1827 | curlun->sense_data = SS_WRITE_ERROR; | |
1828 | curlun->sense_data_info = file_offset >> 9; | |
6174d0fd | 1829 | curlun->info_valid = 1; |
1da177e4 LT |
1830 | break; |
1831 | } | |
1832 | ||
1833 | /* Did the host decide to stop early? */ | |
1834 | if (bh->outreq->actual != bh->outreq->length) { | |
1835 | fsg->short_packet_received = 1; | |
1836 | break; | |
1837 | } | |
1838 | continue; | |
1839 | } | |
1840 | ||
1841 | /* Wait for something to happen */ | |
79a7d9ee AS |
1842 | rc = sleep_thread(fsg); |
1843 | if (rc) | |
1da177e4 LT |
1844 | return rc; |
1845 | } | |
1846 | ||
1847 | return -EIO; // No default reply | |
1848 | } | |
1849 | ||
1850 | ||
1851 | /*-------------------------------------------------------------------------*/ | |
1852 | ||
1853 | /* Sync the file data, don't bother with the metadata. | |
1854 | * This code was copied from fs/buffer.c:sys_fdatasync(). */ | |
1855 | static int fsync_sub(struct lun *curlun) | |
1856 | { | |
1857 | struct file *filp = curlun->filp; | |
1858 | struct inode *inode; | |
1859 | int rc, err; | |
1860 | ||
1861 | if (curlun->ro || !filp) | |
1862 | return 0; | |
1863 | if (!filp->f_op->fsync) | |
1864 | return -EINVAL; | |
1865 | ||
33cb8994 | 1866 | inode = filp->f_path.dentry->d_inode; |
1b1dcc1b | 1867 | mutex_lock(&inode->i_mutex); |
1da177e4 | 1868 | rc = filemap_fdatawrite(inode->i_mapping); |
33cb8994 | 1869 | err = filp->f_op->fsync(filp, filp->f_path.dentry, 1); |
1da177e4 LT |
1870 | if (!rc) |
1871 | rc = err; | |
1872 | err = filemap_fdatawait(inode->i_mapping); | |
1873 | if (!rc) | |
1874 | rc = err; | |
1b1dcc1b | 1875 | mutex_unlock(&inode->i_mutex); |
1da177e4 LT |
1876 | VLDBG(curlun, "fdatasync -> %d\n", rc); |
1877 | return rc; | |
1878 | } | |
1879 | ||
1880 | static void fsync_all(struct fsg_dev *fsg) | |
1881 | { | |
1882 | int i; | |
1883 | ||
1884 | for (i = 0; i < fsg->nluns; ++i) | |
1885 | fsync_sub(&fsg->luns[i]); | |
1886 | } | |
1887 | ||
1888 | static int do_synchronize_cache(struct fsg_dev *fsg) | |
1889 | { | |
1890 | struct lun *curlun = fsg->curlun; | |
1891 | int rc; | |
1892 | ||
1893 | /* We ignore the requested LBA and write out all file's | |
1894 | * dirty data buffers. */ | |
1895 | rc = fsync_sub(curlun); | |
1896 | if (rc) | |
1897 | curlun->sense_data = SS_WRITE_ERROR; | |
1898 | return 0; | |
1899 | } | |
1900 | ||
1901 | ||
1902 | /*-------------------------------------------------------------------------*/ | |
1903 | ||
1904 | static void invalidate_sub(struct lun *curlun) | |
1905 | { | |
1906 | struct file *filp = curlun->filp; | |
33cb8994 | 1907 | struct inode *inode = filp->f_path.dentry->d_inode; |
1da177e4 LT |
1908 | unsigned long rc; |
1909 | ||
fc0ecff6 | 1910 | rc = invalidate_mapping_pages(inode->i_mapping, 0, -1); |
1da177e4 LT |
1911 | VLDBG(curlun, "invalidate_inode_pages -> %ld\n", rc); |
1912 | } | |
1913 | ||
1914 | static int do_verify(struct fsg_dev *fsg) | |
1915 | { | |
1916 | struct lun *curlun = fsg->curlun; | |
1917 | u32 lba; | |
1918 | u32 verification_length; | |
1919 | struct fsg_buffhd *bh = fsg->next_buffhd_to_fill; | |
1920 | loff_t file_offset, file_offset_tmp; | |
1921 | u32 amount_left; | |
1922 | unsigned int amount; | |
1923 | ssize_t nread; | |
1924 | ||
1925 | /* Get the starting Logical Block Address and check that it's | |
1926 | * not too big */ | |
1927 | lba = get_be32(&fsg->cmnd[2]); | |
1928 | if (lba >= curlun->num_sectors) { | |
1929 | curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; | |
1930 | return -EINVAL; | |
1931 | } | |
1932 | ||
1933 | /* We allow DPO (Disable Page Out = don't save data in the | |
1934 | * cache) but we don't implement it. */ | |
1935 | if ((fsg->cmnd[1] & ~0x10) != 0) { | |
1936 | curlun->sense_data = SS_INVALID_FIELD_IN_CDB; | |
1937 | return -EINVAL; | |
1938 | } | |
1939 | ||
1940 | verification_length = get_be16(&fsg->cmnd[7]); | |
1941 | if (unlikely(verification_length == 0)) | |
1942 | return -EIO; // No default reply | |
1943 | ||
1944 | /* Prepare to carry out the file verify */ | |
1945 | amount_left = verification_length << 9; | |
1946 | file_offset = ((loff_t) lba) << 9; | |
1947 | ||
1948 | /* Write out all the dirty buffers before invalidating them */ | |
1949 | fsync_sub(curlun); | |
1950 | if (signal_pending(current)) | |
1951 | return -EINTR; | |
1952 | ||
1953 | invalidate_sub(curlun); | |
1954 | if (signal_pending(current)) | |
1955 | return -EINTR; | |
1956 | ||
1957 | /* Just try to read the requested blocks */ | |
1958 | while (amount_left > 0) { | |
1959 | ||
1960 | /* Figure out how much we need to read: | |
1961 | * Try to read the remaining amount, but not more than | |
1962 | * the buffer size. | |
1963 | * And don't try to read past the end of the file. | |
1964 | * If this means reading 0 then we were asked to read | |
1965 | * past the end of file. */ | |
1966 | amount = min((unsigned int) amount_left, mod_data.buflen); | |
1967 | amount = min((loff_t) amount, | |
1968 | curlun->file_length - file_offset); | |
1969 | if (amount == 0) { | |
1970 | curlun->sense_data = | |
1971 | SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; | |
1972 | curlun->sense_data_info = file_offset >> 9; | |
6174d0fd | 1973 | curlun->info_valid = 1; |
1da177e4 LT |
1974 | break; |
1975 | } | |
1976 | ||
1977 | /* Perform the read */ | |
1978 | file_offset_tmp = file_offset; | |
1979 | nread = vfs_read(curlun->filp, | |
1980 | (char __user *) bh->buf, | |
1981 | amount, &file_offset_tmp); | |
1982 | VLDBG(curlun, "file read %u @ %llu -> %d\n", amount, | |
1983 | (unsigned long long) file_offset, | |
1984 | (int) nread); | |
1985 | if (signal_pending(current)) | |
1986 | return -EINTR; | |
1987 | ||
1988 | if (nread < 0) { | |
1989 | LDBG(curlun, "error in file verify: %d\n", | |
1990 | (int) nread); | |
1991 | nread = 0; | |
1992 | } else if (nread < amount) { | |
1993 | LDBG(curlun, "partial file verify: %d/%u\n", | |
1994 | (int) nread, amount); | |
1995 | nread -= (nread & 511); // Round down to a sector | |
1996 | } | |
1997 | if (nread == 0) { | |
1998 | curlun->sense_data = SS_UNRECOVERED_READ_ERROR; | |
1999 | curlun->sense_data_info = file_offset >> 9; | |
6174d0fd | 2000 | curlun->info_valid = 1; |
1da177e4 LT |
2001 | break; |
2002 | } | |
2003 | file_offset += nread; | |
2004 | amount_left -= nread; | |
2005 | } | |
2006 | return 0; | |
2007 | } | |
2008 | ||
2009 | ||
2010 | /*-------------------------------------------------------------------------*/ | |
2011 | ||
2012 | static int do_inquiry(struct fsg_dev *fsg, struct fsg_buffhd *bh) | |
2013 | { | |
2014 | u8 *buf = (u8 *) bh->buf; | |
2015 | ||
2016 | static char vendor_id[] = "Linux "; | |
2017 | static char product_id[] = "File-Stor Gadget"; | |
2018 | ||
2019 | if (!fsg->curlun) { // Unsupported LUNs are okay | |
2020 | fsg->bad_lun_okay = 1; | |
2021 | memset(buf, 0, 36); | |
2022 | buf[0] = 0x7f; // Unsupported, no device-type | |
2023 | return 36; | |
2024 | } | |
2025 | ||
2026 | memset(buf, 0, 8); // Non-removable, direct-access device | |
2027 | if (mod_data.removable) | |
2028 | buf[1] = 0x80; | |
2029 | buf[2] = 2; // ANSI SCSI level 2 | |
2030 | buf[3] = 2; // SCSI-2 INQUIRY data format | |
2031 | buf[4] = 31; // Additional length | |
2032 | // No special options | |
2033 | sprintf(buf + 8, "%-8s%-16s%04x", vendor_id, product_id, | |
2034 | mod_data.release); | |
2035 | return 36; | |
2036 | } | |
2037 | ||
2038 | ||
2039 | static int do_request_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh) | |
2040 | { | |
2041 | struct lun *curlun = fsg->curlun; | |
2042 | u8 *buf = (u8 *) bh->buf; | |
2043 | u32 sd, sdinfo; | |
6174d0fd | 2044 | int valid; |
1da177e4 LT |
2045 | |
2046 | /* | |
2047 | * From the SCSI-2 spec., section 7.9 (Unit attention condition): | |
2048 | * | |
2049 | * If a REQUEST SENSE command is received from an initiator | |
2050 | * with a pending unit attention condition (before the target | |
2051 | * generates the contingent allegiance condition), then the | |
2052 | * target shall either: | |
2053 | * a) report any pending sense data and preserve the unit | |
2054 | * attention condition on the logical unit, or, | |
2055 | * b) report the unit attention condition, may discard any | |
2056 | * pending sense data, and clear the unit attention | |
2057 | * condition on the logical unit for that initiator. | |
2058 | * | |
2059 | * FSG normally uses option a); enable this code to use option b). | |
2060 | */ | |
2061 | #if 0 | |
2062 | if (curlun && curlun->unit_attention_data != SS_NO_SENSE) { | |
2063 | curlun->sense_data = curlun->unit_attention_data; | |
2064 | curlun->unit_attention_data = SS_NO_SENSE; | |
2065 | } | |
2066 | #endif | |
2067 | ||
2068 | if (!curlun) { // Unsupported LUNs are okay | |
2069 | fsg->bad_lun_okay = 1; | |
2070 | sd = SS_LOGICAL_UNIT_NOT_SUPPORTED; | |
2071 | sdinfo = 0; | |
6174d0fd | 2072 | valid = 0; |
1da177e4 LT |
2073 | } else { |
2074 | sd = curlun->sense_data; | |
2075 | sdinfo = curlun->sense_data_info; | |
6174d0fd | 2076 | valid = curlun->info_valid << 7; |
1da177e4 LT |
2077 | curlun->sense_data = SS_NO_SENSE; |
2078 | curlun->sense_data_info = 0; | |
6174d0fd | 2079 | curlun->info_valid = 0; |
1da177e4 LT |
2080 | } |
2081 | ||
2082 | memset(buf, 0, 18); | |
6174d0fd | 2083 | buf[0] = valid | 0x70; // Valid, current error |
1da177e4 LT |
2084 | buf[2] = SK(sd); |
2085 | put_be32(&buf[3], sdinfo); // Sense information | |
2086 | buf[7] = 18 - 8; // Additional sense length | |
2087 | buf[12] = ASC(sd); | |
2088 | buf[13] = ASCQ(sd); | |
2089 | return 18; | |
2090 | } | |
2091 | ||
2092 | ||
2093 | static int do_read_capacity(struct fsg_dev *fsg, struct fsg_buffhd *bh) | |
2094 | { | |
2095 | struct lun *curlun = fsg->curlun; | |
2096 | u32 lba = get_be32(&fsg->cmnd[2]); | |
2097 | int pmi = fsg->cmnd[8]; | |
2098 | u8 *buf = (u8 *) bh->buf; | |
2099 | ||
2100 | /* Check the PMI and LBA fields */ | |
2101 | if (pmi > 1 || (pmi == 0 && lba != 0)) { | |
2102 | curlun->sense_data = SS_INVALID_FIELD_IN_CDB; | |
2103 | return -EINVAL; | |
2104 | } | |
2105 | ||
2106 | put_be32(&buf[0], curlun->num_sectors - 1); // Max logical block | |
2107 | put_be32(&buf[4], 512); // Block length | |
2108 | return 8; | |
2109 | } | |
2110 | ||
2111 | ||
2112 | static int do_mode_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh) | |
2113 | { | |
2114 | struct lun *curlun = fsg->curlun; | |
2115 | int mscmnd = fsg->cmnd[0]; | |
2116 | u8 *buf = (u8 *) bh->buf; | |
2117 | u8 *buf0 = buf; | |
2118 | int pc, page_code; | |
2119 | int changeable_values, all_pages; | |
2120 | int valid_page = 0; | |
2121 | int len, limit; | |
2122 | ||
2123 | if ((fsg->cmnd[1] & ~0x08) != 0) { // Mask away DBD | |
2124 | curlun->sense_data = SS_INVALID_FIELD_IN_CDB; | |
2125 | return -EINVAL; | |
2126 | } | |
2127 | pc = fsg->cmnd[2] >> 6; | |
2128 | page_code = fsg->cmnd[2] & 0x3f; | |
2129 | if (pc == 3) { | |
2130 | curlun->sense_data = SS_SAVING_PARAMETERS_NOT_SUPPORTED; | |
2131 | return -EINVAL; | |
2132 | } | |
2133 | changeable_values = (pc == 1); | |
2134 | all_pages = (page_code == 0x3f); | |
2135 | ||
2136 | /* Write the mode parameter header. Fixed values are: default | |
2137 | * medium type, no cache control (DPOFUA), and no block descriptors. | |
2138 | * The only variable value is the WriteProtect bit. We will fill in | |
2139 | * the mode data length later. */ | |
2140 | memset(buf, 0, 8); | |
2141 | if (mscmnd == SC_MODE_SENSE_6) { | |
2142 | buf[2] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA | |
2143 | buf += 4; | |
2144 | limit = 255; | |
2145 | } else { // SC_MODE_SENSE_10 | |
2146 | buf[3] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA | |
2147 | buf += 8; | |
2148 | limit = 65535; // Should really be mod_data.buflen | |
2149 | } | |
2150 | ||
2151 | /* No block descriptors */ | |
2152 | ||
2153 | /* The mode pages, in numerical order. The only page we support | |
2154 | * is the Caching page. */ | |
2155 | if (page_code == 0x08 || all_pages) { | |
2156 | valid_page = 1; | |
2157 | buf[0] = 0x08; // Page code | |
2158 | buf[1] = 10; // Page length | |
2159 | memset(buf+2, 0, 10); // None of the fields are changeable | |
2160 | ||
2161 | if (!changeable_values) { | |
2162 | buf[2] = 0x04; // Write cache enable, | |
2163 | // Read cache not disabled | |
2164 | // No cache retention priorities | |
2165 | put_be16(&buf[4], 0xffff); // Don't disable prefetch | |
2166 | // Minimum prefetch = 0 | |
2167 | put_be16(&buf[8], 0xffff); // Maximum prefetch | |
2168 | put_be16(&buf[10], 0xffff); // Maximum prefetch ceiling | |
2169 | } | |
2170 | buf += 12; | |
2171 | } | |
2172 | ||
2173 | /* Check that a valid page was requested and the mode data length | |
2174 | * isn't too long. */ | |
2175 | len = buf - buf0; | |
2176 | if (!valid_page || len > limit) { | |
2177 | curlun->sense_data = SS_INVALID_FIELD_IN_CDB; | |
2178 | return -EINVAL; | |
2179 | } | |
2180 | ||
2181 | /* Store the mode data length */ | |
2182 | if (mscmnd == SC_MODE_SENSE_6) | |
2183 | buf0[0] = len - 1; | |
2184 | else | |
2185 | put_be16(buf0, len - 2); | |
2186 | return len; | |
2187 | } | |
2188 | ||
2189 | ||
2190 | static int do_start_stop(struct fsg_dev *fsg) | |
2191 | { | |
2192 | struct lun *curlun = fsg->curlun; | |
2193 | int loej, start; | |
2194 | ||
2195 | if (!mod_data.removable) { | |
2196 | curlun->sense_data = SS_INVALID_COMMAND; | |
2197 | return -EINVAL; | |
2198 | } | |
2199 | ||
2200 | // int immed = fsg->cmnd[1] & 0x01; | |
2201 | loej = fsg->cmnd[4] & 0x02; | |
2202 | start = fsg->cmnd[4] & 0x01; | |
2203 | ||
2204 | #ifdef CONFIG_USB_FILE_STORAGE_TEST | |
2205 | if ((fsg->cmnd[1] & ~0x01) != 0 || // Mask away Immed | |
2206 | (fsg->cmnd[4] & ~0x03) != 0) { // Mask LoEj, Start | |
2207 | curlun->sense_data = SS_INVALID_FIELD_IN_CDB; | |
2208 | return -EINVAL; | |
2209 | } | |
2210 | ||
2211 | if (!start) { | |
2212 | ||
2213 | /* Are we allowed to unload the media? */ | |
2214 | if (curlun->prevent_medium_removal) { | |
2215 | LDBG(curlun, "unload attempt prevented\n"); | |
2216 | curlun->sense_data = SS_MEDIUM_REMOVAL_PREVENTED; | |
2217 | return -EINVAL; | |
2218 | } | |
2219 | if (loej) { // Simulate an unload/eject | |
2220 | up_read(&fsg->filesem); | |
2221 | down_write(&fsg->filesem); | |
2222 | close_backing_file(curlun); | |
2223 | up_write(&fsg->filesem); | |
2224 | down_read(&fsg->filesem); | |
2225 | } | |
2226 | } else { | |
2227 | ||
2228 | /* Our emulation doesn't support mounting; the medium is | |
2229 | * available for use as soon as it is loaded. */ | |
2230 | if (!backing_file_is_open(curlun)) { | |
2231 | curlun->sense_data = SS_MEDIUM_NOT_PRESENT; | |
2232 | return -EINVAL; | |
2233 | } | |
2234 | } | |
2235 | #endif | |
2236 | return 0; | |
2237 | } | |
2238 | ||
2239 | ||
2240 | static int do_prevent_allow(struct fsg_dev *fsg) | |
2241 | { | |
2242 | struct lun *curlun = fsg->curlun; | |
2243 | int prevent; | |
2244 | ||
2245 | if (!mod_data.removable) { | |
2246 | curlun->sense_data = SS_INVALID_COMMAND; | |
2247 | return -EINVAL; | |
2248 | } | |
2249 | ||
2250 | prevent = fsg->cmnd[4] & 0x01; | |
2251 | if ((fsg->cmnd[4] & ~0x01) != 0) { // Mask away Prevent | |
2252 | curlun->sense_data = SS_INVALID_FIELD_IN_CDB; | |
2253 | return -EINVAL; | |
2254 | } | |
2255 | ||
2256 | if (curlun->prevent_medium_removal && !prevent) | |
2257 | fsync_sub(curlun); | |
2258 | curlun->prevent_medium_removal = prevent; | |
2259 | return 0; | |
2260 | } | |
2261 | ||
2262 | ||
2263 | static int do_read_format_capacities(struct fsg_dev *fsg, | |
2264 | struct fsg_buffhd *bh) | |
2265 | { | |
2266 | struct lun *curlun = fsg->curlun; | |
2267 | u8 *buf = (u8 *) bh->buf; | |
2268 | ||
2269 | buf[0] = buf[1] = buf[2] = 0; | |
2270 | buf[3] = 8; // Only the Current/Maximum Capacity Descriptor | |
2271 | buf += 4; | |
2272 | ||
2273 | put_be32(&buf[0], curlun->num_sectors); // Number of blocks | |
2274 | put_be32(&buf[4], 512); // Block length | |
2275 | buf[4] = 0x02; // Current capacity | |
2276 | return 12; | |
2277 | } | |
2278 | ||
2279 | ||
2280 | static int do_mode_select(struct fsg_dev *fsg, struct fsg_buffhd *bh) | |
2281 | { | |
2282 | struct lun *curlun = fsg->curlun; | |
2283 | ||
2284 | /* We don't support MODE SELECT */ | |
2285 | curlun->sense_data = SS_INVALID_COMMAND; | |
2286 | return -EINVAL; | |
2287 | } | |
2288 | ||
2289 | ||
2290 | /*-------------------------------------------------------------------------*/ | |
2291 | ||
2292 | static int halt_bulk_in_endpoint(struct fsg_dev *fsg) | |
2293 | { | |
2294 | int rc; | |
2295 | ||
2296 | rc = fsg_set_halt(fsg, fsg->bulk_in); | |
2297 | if (rc == -EAGAIN) | |
2298 | VDBG(fsg, "delayed bulk-in endpoint halt\n"); | |
2299 | while (rc != 0) { | |
2300 | if (rc != -EAGAIN) { | |
2301 | WARN(fsg, "usb_ep_set_halt -> %d\n", rc); | |
2302 | rc = 0; | |
2303 | break; | |
2304 | } | |
2305 | ||
2306 | /* Wait for a short time and then try again */ | |
2307 | if (msleep_interruptible(100) != 0) | |
2308 | return -EINTR; | |
2309 | rc = usb_ep_set_halt(fsg->bulk_in); | |
2310 | } | |
2311 | return rc; | |
2312 | } | |
2313 | ||
2314 | static int pad_with_zeros(struct fsg_dev *fsg) | |
2315 | { | |
2316 | struct fsg_buffhd *bh = fsg->next_buffhd_to_fill; | |
2317 | u32 nkeep = bh->inreq->length; | |
2318 | u32 nsend; | |
2319 | int rc; | |
2320 | ||
2321 | bh->state = BUF_STATE_EMPTY; // For the first iteration | |
2322 | fsg->usb_amount_left = nkeep + fsg->residue; | |
2323 | while (fsg->usb_amount_left > 0) { | |
2324 | ||
2325 | /* Wait for the next buffer to be free */ | |
2326 | while (bh->state != BUF_STATE_EMPTY) { | |
79a7d9ee AS |
2327 | rc = sleep_thread(fsg); |
2328 | if (rc) | |
1da177e4 LT |
2329 | return rc; |
2330 | } | |
2331 | ||
2332 | nsend = min(fsg->usb_amount_left, (u32) mod_data.buflen); | |
2333 | memset(bh->buf + nkeep, 0, nsend - nkeep); | |
2334 | bh->inreq->length = nsend; | |
2335 | bh->inreq->zero = 0; | |
2336 | start_transfer(fsg, fsg->bulk_in, bh->inreq, | |
2337 | &bh->inreq_busy, &bh->state); | |
2338 | bh = fsg->next_buffhd_to_fill = bh->next; | |
2339 | fsg->usb_amount_left -= nsend; | |
2340 | nkeep = 0; | |
2341 | } | |
2342 | return 0; | |
2343 | } | |
2344 | ||
2345 | static int throw_away_data(struct fsg_dev *fsg) | |
2346 | { | |
2347 | struct fsg_buffhd *bh; | |
2348 | u32 amount; | |
2349 | int rc; | |
2350 | ||
2351 | while ((bh = fsg->next_buffhd_to_drain)->state != BUF_STATE_EMPTY || | |
2352 | fsg->usb_amount_left > 0) { | |
2353 | ||
2354 | /* Throw away the data in a filled buffer */ | |
2355 | if (bh->state == BUF_STATE_FULL) { | |
a21d4fed | 2356 | smp_rmb(); |
1da177e4 LT |
2357 | bh->state = BUF_STATE_EMPTY; |
2358 | fsg->next_buffhd_to_drain = bh->next; | |
2359 | ||
2360 | /* A short packet or an error ends everything */ | |
2361 | if (bh->outreq->actual != bh->outreq->length || | |
2362 | bh->outreq->status != 0) { | |
2363 | raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT); | |
2364 | return -EINTR; | |
2365 | } | |
2366 | continue; | |
2367 | } | |
2368 | ||
2369 | /* Try to submit another request if we need one */ | |
2370 | bh = fsg->next_buffhd_to_fill; | |
2371 | if (bh->state == BUF_STATE_EMPTY && fsg->usb_amount_left > 0) { | |
2372 | amount = min(fsg->usb_amount_left, | |
2373 | (u32) mod_data.buflen); | |
2374 | ||
2375 | /* amount is always divisible by 512, hence by | |
2376 | * the bulk-out maxpacket size */ | |
2377 | bh->outreq->length = bh->bulk_out_intended_length = | |
2378 | amount; | |
70ffe6e1 | 2379 | bh->outreq->short_not_ok = 1; |
1da177e4 LT |
2380 | start_transfer(fsg, fsg->bulk_out, bh->outreq, |
2381 | &bh->outreq_busy, &bh->state); | |
2382 | fsg->next_buffhd_to_fill = bh->next; | |
2383 | fsg->usb_amount_left -= amount; | |
2384 | continue; | |
2385 | } | |
2386 | ||
2387 | /* Otherwise wait for something to happen */ | |
79a7d9ee AS |
2388 | rc = sleep_thread(fsg); |
2389 | if (rc) | |
1da177e4 LT |
2390 | return rc; |
2391 | } | |
2392 | return 0; | |
2393 | } | |
2394 | ||
2395 | ||
2396 | static int finish_reply(struct fsg_dev *fsg) | |
2397 | { | |
2398 | struct fsg_buffhd *bh = fsg->next_buffhd_to_fill; | |
2399 | int rc = 0; | |
2400 | ||
2401 | switch (fsg->data_dir) { | |
2402 | case DATA_DIR_NONE: | |
2403 | break; // Nothing to send | |
2404 | ||
2405 | /* If we don't know whether the host wants to read or write, | |
2406 | * this must be CB or CBI with an unknown command. We mustn't | |
2407 | * try to send or receive any data. So stall both bulk pipes | |
2408 | * if we can and wait for a reset. */ | |
2409 | case DATA_DIR_UNKNOWN: | |
2410 | if (mod_data.can_stall) { | |
2411 | fsg_set_halt(fsg, fsg->bulk_out); | |
2412 | rc = halt_bulk_in_endpoint(fsg); | |
2413 | } | |
2414 | break; | |
2415 | ||
2416 | /* All but the last buffer of data must have already been sent */ | |
2417 | case DATA_DIR_TO_HOST: | |
2418 | if (fsg->data_size == 0) | |
2419 | ; // Nothing to send | |
2420 | ||
2421 | /* If there's no residue, simply send the last buffer */ | |
2422 | else if (fsg->residue == 0) { | |
2423 | bh->inreq->zero = 0; | |
2424 | start_transfer(fsg, fsg->bulk_in, bh->inreq, | |
2425 | &bh->inreq_busy, &bh->state); | |
2426 | fsg->next_buffhd_to_fill = bh->next; | |
2427 | } | |
2428 | ||
2429 | /* There is a residue. For CB and CBI, simply mark the end | |
2430 | * of the data with a short packet. However, if we are | |
2431 | * allowed to stall, there was no data at all (residue == | |
2432 | * data_size), and the command failed (invalid LUN or | |
2433 | * sense data is set), then halt the bulk-in endpoint | |
2434 | * instead. */ | |
2435 | else if (!transport_is_bbb()) { | |
2436 | if (mod_data.can_stall && | |
2437 | fsg->residue == fsg->data_size && | |
2438 | (!fsg->curlun || fsg->curlun->sense_data != SS_NO_SENSE)) { | |
2439 | bh->state = BUF_STATE_EMPTY; | |
2440 | rc = halt_bulk_in_endpoint(fsg); | |
2441 | } else { | |
2442 | bh->inreq->zero = 1; | |
2443 | start_transfer(fsg, fsg->bulk_in, bh->inreq, | |
2444 | &bh->inreq_busy, &bh->state); | |
2445 | fsg->next_buffhd_to_fill = bh->next; | |
2446 | } | |
2447 | } | |
2448 | ||
2449 | /* For Bulk-only, if we're allowed to stall then send the | |
2450 | * short packet and halt the bulk-in endpoint. If we can't | |
2451 | * stall, pad out the remaining data with 0's. */ | |
2452 | else { | |
2453 | if (mod_data.can_stall) { | |
2454 | bh->inreq->zero = 1; | |
2455 | start_transfer(fsg, fsg->bulk_in, bh->inreq, | |
2456 | &bh->inreq_busy, &bh->state); | |
2457 | fsg->next_buffhd_to_fill = bh->next; | |
2458 | rc = halt_bulk_in_endpoint(fsg); | |
2459 | } else | |
2460 | rc = pad_with_zeros(fsg); | |
2461 | } | |
2462 | break; | |
2463 | ||
2464 | /* We have processed all we want from the data the host has sent. | |
2465 | * There may still be outstanding bulk-out requests. */ | |
2466 | case DATA_DIR_FROM_HOST: | |
2467 | if (fsg->residue == 0) | |
2468 | ; // Nothing to receive | |
2469 | ||
2470 | /* Did the host stop sending unexpectedly early? */ | |
2471 | else if (fsg->short_packet_received) { | |
2472 | raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT); | |
2473 | rc = -EINTR; | |
2474 | } | |
2475 | ||
2476 | /* We haven't processed all the incoming data. Even though | |
2477 | * we may be allowed to stall, doing so would cause a race. | |
2478 | * The controller may already have ACK'ed all the remaining | |
2479 | * bulk-out packets, in which case the host wouldn't see a | |
2480 | * STALL. Not realizing the endpoint was halted, it wouldn't | |
2481 | * clear the halt -- leading to problems later on. */ | |
2482 | #if 0 | |
2483 | else if (mod_data.can_stall) { | |
2484 | fsg_set_halt(fsg, fsg->bulk_out); | |
2485 | raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT); | |
2486 | rc = -EINTR; | |
2487 | } | |
2488 | #endif | |
2489 | ||
2490 | /* We can't stall. Read in the excess data and throw it | |
2491 | * all away. */ | |
2492 | else | |
2493 | rc = throw_away_data(fsg); | |
2494 | break; | |
2495 | } | |
2496 | return rc; | |
2497 | } | |
2498 | ||
2499 | ||
2500 | static int send_status(struct fsg_dev *fsg) | |
2501 | { | |
2502 | struct lun *curlun = fsg->curlun; | |
2503 | struct fsg_buffhd *bh; | |
2504 | int rc; | |
2505 | u8 status = USB_STATUS_PASS; | |
2506 | u32 sd, sdinfo = 0; | |
2507 | ||
2508 | /* Wait for the next buffer to become available */ | |
2509 | bh = fsg->next_buffhd_to_fill; | |
2510 | while (bh->state != BUF_STATE_EMPTY) { | |
79a7d9ee AS |
2511 | rc = sleep_thread(fsg); |
2512 | if (rc) | |
1da177e4 LT |
2513 | return rc; |
2514 | } | |
2515 | ||
2516 | if (curlun) { | |
2517 | sd = curlun->sense_data; | |
2518 | sdinfo = curlun->sense_data_info; | |
2519 | } else if (fsg->bad_lun_okay) | |
2520 | sd = SS_NO_SENSE; | |
2521 | else | |
2522 | sd = SS_LOGICAL_UNIT_NOT_SUPPORTED; | |
2523 | ||
2524 | if (fsg->phase_error) { | |
2525 | DBG(fsg, "sending phase-error status\n"); | |
2526 | status = USB_STATUS_PHASE_ERROR; | |
2527 | sd = SS_INVALID_COMMAND; | |
2528 | } else if (sd != SS_NO_SENSE) { | |
2529 | DBG(fsg, "sending command-failure status\n"); | |
2530 | status = USB_STATUS_FAIL; | |
2531 | VDBG(fsg, " sense data: SK x%02x, ASC x%02x, ASCQ x%02x;" | |
2532 | " info x%x\n", | |
2533 | SK(sd), ASC(sd), ASCQ(sd), sdinfo); | |
2534 | } | |
2535 | ||
2536 | if (transport_is_bbb()) { | |
7ca46b86 | 2537 | struct bulk_cs_wrap *csw = bh->buf; |
1da177e4 LT |
2538 | |
2539 | /* Store and send the Bulk-only CSW */ | |
2540 | csw->Signature = __constant_cpu_to_le32(USB_BULK_CS_SIG); | |
2541 | csw->Tag = fsg->tag; | |
2542 | csw->Residue = cpu_to_le32(fsg->residue); | |
2543 | csw->Status = status; | |
2544 | ||
2545 | bh->inreq->length = USB_BULK_CS_WRAP_LEN; | |
2546 | bh->inreq->zero = 0; | |
2547 | start_transfer(fsg, fsg->bulk_in, bh->inreq, | |
2548 | &bh->inreq_busy, &bh->state); | |
2549 | ||
2550 | } else if (mod_data.transport_type == USB_PR_CB) { | |
2551 | ||
2552 | /* Control-Bulk transport has no status phase! */ | |
2553 | return 0; | |
2554 | ||
2555 | } else { // USB_PR_CBI | |
7ca46b86 | 2556 | struct interrupt_data *buf = bh->buf; |
1da177e4 LT |
2557 | |
2558 | /* Store and send the Interrupt data. UFI sends the ASC | |
2559 | * and ASCQ bytes. Everything else sends a Type (which | |
2560 | * is always 0) and the status Value. */ | |
2561 | if (mod_data.protocol_type == USB_SC_UFI) { | |
2562 | buf->bType = ASC(sd); | |
2563 | buf->bValue = ASCQ(sd); | |
2564 | } else { | |
2565 | buf->bType = 0; | |
2566 | buf->bValue = status; | |
2567 | } | |
2568 | fsg->intreq->length = CBI_INTERRUPT_DATA_LEN; | |
2569 | ||
2570 | fsg->intr_buffhd = bh; // Point to the right buffhd | |
2571 | fsg->intreq->buf = bh->inreq->buf; | |
1da177e4 LT |
2572 | fsg->intreq->context = bh; |
2573 | start_transfer(fsg, fsg->intr_in, fsg->intreq, | |
2574 | &fsg->intreq_busy, &bh->state); | |
2575 | } | |
2576 | ||
2577 | fsg->next_buffhd_to_fill = bh->next; | |
2578 | return 0; | |
2579 | } | |
2580 | ||
2581 | ||
2582 | /*-------------------------------------------------------------------------*/ | |
2583 | ||
2584 | /* Check whether the command is properly formed and whether its data size | |
2585 | * and direction agree with the values we already have. */ | |
2586 | static int check_command(struct fsg_dev *fsg, int cmnd_size, | |
2587 | enum data_direction data_dir, unsigned int mask, | |
2588 | int needs_medium, const char *name) | |
2589 | { | |
2590 | int i; | |
2591 | int lun = fsg->cmnd[1] >> 5; | |
2592 | static const char dirletter[4] = {'u', 'o', 'i', 'n'}; | |
2593 | char hdlen[20]; | |
2594 | struct lun *curlun; | |
2595 | ||
2596 | /* Adjust the expected cmnd_size for protocol encapsulation padding. | |
2597 | * Transparent SCSI doesn't pad. */ | |
2598 | if (protocol_is_scsi()) | |
2599 | ; | |
2600 | ||
2601 | /* There's some disagreement as to whether RBC pads commands or not. | |
2602 | * We'll play it safe and accept either form. */ | |
2603 | else if (mod_data.protocol_type == USB_SC_RBC) { | |
2604 | if (fsg->cmnd_size == 12) | |
2605 | cmnd_size = 12; | |
2606 | ||
2607 | /* All the other protocols pad to 12 bytes */ | |
2608 | } else | |
2609 | cmnd_size = 12; | |
2610 | ||
2611 | hdlen[0] = 0; | |
2612 | if (fsg->data_dir != DATA_DIR_UNKNOWN) | |
2613 | sprintf(hdlen, ", H%c=%u", dirletter[(int) fsg->data_dir], | |
2614 | fsg->data_size); | |
2615 | VDBG(fsg, "SCSI command: %s; Dc=%d, D%c=%u; Hc=%d%s\n", | |
2616 | name, cmnd_size, dirletter[(int) data_dir], | |
2617 | fsg->data_size_from_cmnd, fsg->cmnd_size, hdlen); | |
2618 | ||
2619 | /* We can't reply at all until we know the correct data direction | |
2620 | * and size. */ | |
2621 | if (fsg->data_size_from_cmnd == 0) | |
2622 | data_dir = DATA_DIR_NONE; | |
2623 | if (fsg->data_dir == DATA_DIR_UNKNOWN) { // CB or CBI | |
2624 | fsg->data_dir = data_dir; | |
2625 | fsg->data_size = fsg->data_size_from_cmnd; | |
2626 | ||
2627 | } else { // Bulk-only | |
2628 | if (fsg->data_size < fsg->data_size_from_cmnd) { | |
2629 | ||
2630 | /* Host data size < Device data size is a phase error. | |
2631 | * Carry out the command, but only transfer as much | |
2632 | * as we are allowed. */ | |
2633 | fsg->data_size_from_cmnd = fsg->data_size; | |
2634 | fsg->phase_error = 1; | |
2635 | } | |
2636 | } | |
2637 | fsg->residue = fsg->usb_amount_left = fsg->data_size; | |
2638 | ||
2639 | /* Conflicting data directions is a phase error */ | |
2640 | if (fsg->data_dir != data_dir && fsg->data_size_from_cmnd > 0) { | |
2641 | fsg->phase_error = 1; | |
2642 | return -EINVAL; | |
2643 | } | |
2644 | ||
2645 | /* Verify the length of the command itself */ | |
2646 | if (cmnd_size != fsg->cmnd_size) { | |
2647 | ||
2648 | /* Special case workaround: MS-Windows issues REQUEST SENSE | |
2649 | * with cbw->Length == 12 (it should be 6). */ | |
2650 | if (fsg->cmnd[0] == SC_REQUEST_SENSE && fsg->cmnd_size == 12) | |
2651 | cmnd_size = fsg->cmnd_size; | |
2652 | else { | |
2653 | fsg->phase_error = 1; | |
2654 | return -EINVAL; | |
2655 | } | |
2656 | } | |
2657 | ||
d794ac7a | 2658 | /* Check that the LUN values are consistent */ |
1da177e4 LT |
2659 | if (transport_is_bbb()) { |
2660 | if (fsg->lun != lun) | |
2661 | DBG(fsg, "using LUN %d from CBW, " | |
2662 | "not LUN %d from CDB\n", | |
2663 | fsg->lun, lun); | |
2664 | } else | |
2665 | fsg->lun = lun; // Use LUN from the command | |
2666 | ||
2667 | /* Check the LUN */ | |
2668 | if (fsg->lun >= 0 && fsg->lun < fsg->nluns) { | |
2669 | fsg->curlun = curlun = &fsg->luns[fsg->lun]; | |
2670 | if (fsg->cmnd[0] != SC_REQUEST_SENSE) { | |
2671 | curlun->sense_data = SS_NO_SENSE; | |
2672 | curlun->sense_data_info = 0; | |
6174d0fd | 2673 | curlun->info_valid = 0; |
1da177e4 LT |
2674 | } |
2675 | } else { | |
2676 | fsg->curlun = curlun = NULL; | |
2677 | fsg->bad_lun_okay = 0; | |
2678 | ||
2679 | /* INQUIRY and REQUEST SENSE commands are explicitly allowed | |
2680 | * to use unsupported LUNs; all others may not. */ | |
2681 | if (fsg->cmnd[0] != SC_INQUIRY && | |
2682 | fsg->cmnd[0] != SC_REQUEST_SENSE) { | |
2683 | DBG(fsg, "unsupported LUN %d\n", fsg->lun); | |
2684 | return -EINVAL; | |
2685 | } | |
2686 | } | |
2687 | ||
2688 | /* If a unit attention condition exists, only INQUIRY and | |
2689 | * REQUEST SENSE commands are allowed; anything else must fail. */ | |
2690 | if (curlun && curlun->unit_attention_data != SS_NO_SENSE && | |
2691 | fsg->cmnd[0] != SC_INQUIRY && | |
2692 | fsg->cmnd[0] != SC_REQUEST_SENSE) { | |
2693 | curlun->sense_data = curlun->unit_attention_data; | |
2694 | curlun->unit_attention_data = SS_NO_SENSE; | |
2695 | return -EINVAL; | |
2696 | } | |
2697 | ||
2698 | /* Check that only command bytes listed in the mask are non-zero */ | |
2699 | fsg->cmnd[1] &= 0x1f; // Mask away the LUN | |
2700 | for (i = 1; i < cmnd_size; ++i) { | |
2701 | if (fsg->cmnd[i] && !(mask & (1 << i))) { | |
2702 | if (curlun) | |
2703 | curlun->sense_data = SS_INVALID_FIELD_IN_CDB; | |
2704 | return -EINVAL; | |
2705 | } | |
2706 | } | |
2707 | ||
2708 | /* If the medium isn't mounted and the command needs to access | |
2709 | * it, return an error. */ | |
2710 | if (curlun && !backing_file_is_open(curlun) && needs_medium) { | |
2711 | curlun->sense_data = SS_MEDIUM_NOT_PRESENT; | |
2712 | return -EINVAL; | |
2713 | } | |
2714 | ||
2715 | return 0; | |
2716 | } | |
2717 | ||
2718 | ||
2719 | static int do_scsi_command(struct fsg_dev *fsg) | |
2720 | { | |
2721 | struct fsg_buffhd *bh; | |
2722 | int rc; | |
2723 | int reply = -EINVAL; | |
2724 | int i; | |
2725 | static char unknown[16]; | |
2726 | ||
2727 | dump_cdb(fsg); | |
2728 | ||
2729 | /* Wait for the next buffer to become available for data or status */ | |
2730 | bh = fsg->next_buffhd_to_drain = fsg->next_buffhd_to_fill; | |
2731 | while (bh->state != BUF_STATE_EMPTY) { | |
79a7d9ee AS |
2732 | rc = sleep_thread(fsg); |
2733 | if (rc) | |
1da177e4 | 2734 | return rc; |
79a7d9ee | 2735 | } |
1da177e4 LT |
2736 | fsg->phase_error = 0; |
2737 | fsg->short_packet_received = 0; | |
2738 | ||
2739 | down_read(&fsg->filesem); // We're using the backing file | |
2740 | switch (fsg->cmnd[0]) { | |
2741 | ||
2742 | case SC_INQUIRY: | |
2743 | fsg->data_size_from_cmnd = fsg->cmnd[4]; | |
2744 | if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST, | |
2745 | (1<<4), 0, | |
2746 | "INQUIRY")) == 0) | |
2747 | reply = do_inquiry(fsg, bh); | |
2748 | break; | |
2749 | ||
2750 | case SC_MODE_SELECT_6: | |
2751 | fsg->data_size_from_cmnd = fsg->cmnd[4]; | |
2752 | if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST, | |
2753 | (1<<1) | (1<<4), 0, | |
2754 | "MODE SELECT(6)")) == 0) | |
2755 | reply = do_mode_select(fsg, bh); | |
2756 | break; | |
2757 | ||
2758 | case SC_MODE_SELECT_10: | |
2759 | fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]); | |
2760 | if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST, | |
2761 | (1<<1) | (3<<7), 0, | |
2762 | "MODE SELECT(10)")) == 0) | |
2763 | reply = do_mode_select(fsg, bh); | |
2764 | break; | |
2765 | ||
2766 | case SC_MODE_SENSE_6: | |
2767 | fsg->data_size_from_cmnd = fsg->cmnd[4]; | |
2768 | if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST, | |
2769 | (1<<1) | (1<<2) | (1<<4), 0, | |
2770 | "MODE SENSE(6)")) == 0) | |
2771 | reply = do_mode_sense(fsg, bh); | |
2772 | break; | |
2773 | ||
2774 | case SC_MODE_SENSE_10: | |
2775 | fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]); | |
2776 | if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST, | |
2777 | (1<<1) | (1<<2) | (3<<7), 0, | |
2778 | "MODE SENSE(10)")) == 0) | |
2779 | reply = do_mode_sense(fsg, bh); | |
2780 | break; | |
2781 | ||
2782 | case SC_PREVENT_ALLOW_MEDIUM_REMOVAL: | |
2783 | fsg->data_size_from_cmnd = 0; | |
2784 | if ((reply = check_command(fsg, 6, DATA_DIR_NONE, | |
2785 | (1<<4), 0, | |
2786 | "PREVENT-ALLOW MEDIUM REMOVAL")) == 0) | |
2787 | reply = do_prevent_allow(fsg); | |
2788 | break; | |
2789 | ||
2790 | case SC_READ_6: | |
2791 | i = fsg->cmnd[4]; | |
2792 | fsg->data_size_from_cmnd = (i == 0 ? 256 : i) << 9; | |
2793 | if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST, | |
2794 | (7<<1) | (1<<4), 1, | |
2795 | "READ(6)")) == 0) | |
2796 | reply = do_read(fsg); | |
2797 | break; | |
2798 | ||
2799 | case SC_READ_10: | |
2800 | fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]) << 9; | |
2801 | if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST, | |
2802 | (1<<1) | (0xf<<2) | (3<<7), 1, | |
2803 | "READ(10)")) == 0) | |
2804 | reply = do_read(fsg); | |
2805 | break; | |
2806 | ||
2807 | case SC_READ_12: | |
2808 | fsg->data_size_from_cmnd = get_be32(&fsg->cmnd[6]) << 9; | |
2809 | if ((reply = check_command(fsg, 12, DATA_DIR_TO_HOST, | |
2810 | (1<<1) | (0xf<<2) | (0xf<<6), 1, | |
2811 | "READ(12)")) == 0) | |
2812 | reply = do_read(fsg); | |
2813 | break; | |
2814 | ||
2815 | case SC_READ_CAPACITY: | |
2816 | fsg->data_size_from_cmnd = 8; | |
2817 | if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST, | |
2818 | (0xf<<2) | (1<<8), 1, | |
2819 | "READ CAPACITY")) == 0) | |
2820 | reply = do_read_capacity(fsg, bh); | |
2821 | break; | |
2822 | ||
2823 | case SC_READ_FORMAT_CAPACITIES: | |
2824 | fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]); | |
2825 | if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST, | |
2826 | (3<<7), 1, | |
2827 | "READ FORMAT CAPACITIES")) == 0) | |
2828 | reply = do_read_format_capacities(fsg, bh); | |
2829 | break; | |
2830 | ||
2831 | case SC_REQUEST_SENSE: | |
2832 | fsg->data_size_from_cmnd = fsg->cmnd[4]; | |
2833 | if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST, | |
2834 | (1<<4), 0, | |
2835 | "REQUEST SENSE")) == 0) | |
2836 | reply = do_request_sense(fsg, bh); | |
2837 | break; | |
2838 | ||
2839 | case SC_START_STOP_UNIT: | |
2840 | fsg->data_size_from_cmnd = 0; | |
2841 | if ((reply = check_command(fsg, 6, DATA_DIR_NONE, | |
2842 | (1<<1) | (1<<4), 0, | |
2843 | "START-STOP UNIT")) == 0) | |
2844 | reply = do_start_stop(fsg); | |
2845 | break; | |
2846 | ||
2847 | case SC_SYNCHRONIZE_CACHE: | |
2848 | fsg->data_size_from_cmnd = 0; | |
2849 | if ((reply = check_command(fsg, 10, DATA_DIR_NONE, | |
2850 | (0xf<<2) | (3<<7), 1, | |
2851 | "SYNCHRONIZE CACHE")) == 0) | |
2852 | reply = do_synchronize_cache(fsg); | |
2853 | break; | |
2854 | ||
2855 | case SC_TEST_UNIT_READY: | |
2856 | fsg->data_size_from_cmnd = 0; | |
2857 | reply = check_command(fsg, 6, DATA_DIR_NONE, | |
2858 | 0, 1, | |
2859 | "TEST UNIT READY"); | |
2860 | break; | |
2861 | ||
2862 | /* Although optional, this command is used by MS-Windows. We | |
2863 | * support a minimal version: BytChk must be 0. */ | |
2864 | case SC_VERIFY: | |
2865 | fsg->data_size_from_cmnd = 0; | |
2866 | if ((reply = check_command(fsg, 10, DATA_DIR_NONE, | |
2867 | (1<<1) | (0xf<<2) | (3<<7), 1, | |
2868 | "VERIFY")) == 0) | |
2869 | reply = do_verify(fsg); | |
2870 | break; | |
2871 | ||
2872 | case SC_WRITE_6: | |
2873 | i = fsg->cmnd[4]; | |
2874 | fsg->data_size_from_cmnd = (i == 0 ? 256 : i) << 9; | |
2875 | if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST, | |
2876 | (7<<1) | (1<<4), 1, | |
2877 | "WRITE(6)")) == 0) | |
2878 | reply = do_write(fsg); | |
2879 | break; | |
2880 | ||
2881 | case SC_WRITE_10: | |
2882 | fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]) << 9; | |
2883 | if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST, | |
2884 | (1<<1) | (0xf<<2) | (3<<7), 1, | |
2885 | "WRITE(10)")) == 0) | |
2886 | reply = do_write(fsg); | |
2887 | break; | |
2888 | ||
2889 | case SC_WRITE_12: | |
2890 | fsg->data_size_from_cmnd = get_be32(&fsg->cmnd[6]) << 9; | |
2891 | if ((reply = check_command(fsg, 12, DATA_DIR_FROM_HOST, | |
2892 | (1<<1) | (0xf<<2) | (0xf<<6), 1, | |
2893 | "WRITE(12)")) == 0) | |
2894 | reply = do_write(fsg); | |
2895 | break; | |
2896 | ||
2897 | /* Some mandatory commands that we recognize but don't implement. | |
2898 | * They don't mean much in this setting. It's left as an exercise | |
2899 | * for anyone interested to implement RESERVE and RELEASE in terms | |
2900 | * of Posix locks. */ | |
2901 | case SC_FORMAT_UNIT: | |
2902 | case SC_RELEASE: | |
2903 | case SC_RESERVE: | |
2904 | case SC_SEND_DIAGNOSTIC: | |
2905 | // Fall through | |
2906 | ||
2907 | default: | |
2908 | fsg->data_size_from_cmnd = 0; | |
2909 | sprintf(unknown, "Unknown x%02x", fsg->cmnd[0]); | |
2910 | if ((reply = check_command(fsg, fsg->cmnd_size, | |
2911 | DATA_DIR_UNKNOWN, 0xff, 0, unknown)) == 0) { | |
2912 | fsg->curlun->sense_data = SS_INVALID_COMMAND; | |
2913 | reply = -EINVAL; | |
2914 | } | |
2915 | break; | |
2916 | } | |
2917 | up_read(&fsg->filesem); | |
2918 | ||
2919 | if (reply == -EINTR || signal_pending(current)) | |
2920 | return -EINTR; | |
2921 | ||
2922 | /* Set up the single reply buffer for finish_reply() */ | |
2923 | if (reply == -EINVAL) | |
2924 | reply = 0; // Error reply length | |
2925 | if (reply >= 0 && fsg->data_dir == DATA_DIR_TO_HOST) { | |
2926 | reply = min((u32) reply, fsg->data_size_from_cmnd); | |
2927 | bh->inreq->length = reply; | |
2928 | bh->state = BUF_STATE_FULL; | |
2929 | fsg->residue -= reply; | |
2930 | } // Otherwise it's already set | |
2931 | ||
2932 | return 0; | |
2933 | } | |
2934 | ||
2935 | ||
2936 | /*-------------------------------------------------------------------------*/ | |
2937 | ||
2938 | static int received_cbw(struct fsg_dev *fsg, struct fsg_buffhd *bh) | |
2939 | { | |
2940 | struct usb_request *req = bh->outreq; | |
7ca46b86 | 2941 | struct bulk_cb_wrap *cbw = req->buf; |
1da177e4 LT |
2942 | |
2943 | /* Was this a real packet? */ | |
2944 | if (req->status) | |
2945 | return -EINVAL; | |
2946 | ||
2947 | /* Is the CBW valid? */ | |
2948 | if (req->actual != USB_BULK_CB_WRAP_LEN || | |
2949 | cbw->Signature != __constant_cpu_to_le32( | |
2950 | USB_BULK_CB_SIG)) { | |
2951 | DBG(fsg, "invalid CBW: len %u sig 0x%x\n", | |
2952 | req->actual, | |
2953 | le32_to_cpu(cbw->Signature)); | |
2954 | ||
2955 | /* The Bulk-only spec says we MUST stall the bulk pipes! | |
2956 | * If we want to avoid stalls, set a flag so that we will | |
2957 | * clear the endpoint halts at the next reset. */ | |
2958 | if (!mod_data.can_stall) | |
2959 | set_bit(CLEAR_BULK_HALTS, &fsg->atomic_bitflags); | |
2960 | fsg_set_halt(fsg, fsg->bulk_out); | |
2961 | halt_bulk_in_endpoint(fsg); | |
2962 | return -EINVAL; | |
2963 | } | |
2964 | ||
2965 | /* Is the CBW meaningful? */ | |
2966 | if (cbw->Lun >= MAX_LUNS || cbw->Flags & ~USB_BULK_IN_FLAG || | |
12943f09 | 2967 | cbw->Length <= 0 || cbw->Length > MAX_COMMAND_SIZE) { |
1da177e4 LT |
2968 | DBG(fsg, "non-meaningful CBW: lun = %u, flags = 0x%x, " |
2969 | "cmdlen %u\n", | |
2970 | cbw->Lun, cbw->Flags, cbw->Length); | |
2971 | ||
2972 | /* We can do anything we want here, so let's stall the | |
2973 | * bulk pipes if we are allowed to. */ | |
2974 | if (mod_data.can_stall) { | |
2975 | fsg_set_halt(fsg, fsg->bulk_out); | |
2976 | halt_bulk_in_endpoint(fsg); | |
2977 | } | |
2978 | return -EINVAL; | |
2979 | } | |
2980 | ||
2981 | /* Save the command for later */ | |
2982 | fsg->cmnd_size = cbw->Length; | |
2983 | memcpy(fsg->cmnd, cbw->CDB, fsg->cmnd_size); | |
2984 | if (cbw->Flags & USB_BULK_IN_FLAG) | |
2985 | fsg->data_dir = DATA_DIR_TO_HOST; | |
2986 | else | |
2987 | fsg->data_dir = DATA_DIR_FROM_HOST; | |
2988 | fsg->data_size = le32_to_cpu(cbw->DataTransferLength); | |
2989 | if (fsg->data_size == 0) | |
2990 | fsg->data_dir = DATA_DIR_NONE; | |
2991 | fsg->lun = cbw->Lun; | |
2992 | fsg->tag = cbw->Tag; | |
2993 | return 0; | |
2994 | } | |
2995 | ||
2996 | ||
2997 | static int get_next_command(struct fsg_dev *fsg) | |
2998 | { | |
2999 | struct fsg_buffhd *bh; | |
3000 | int rc = 0; | |
3001 | ||
3002 | if (transport_is_bbb()) { | |
3003 | ||
3004 | /* Wait for the next buffer to become available */ | |
3005 | bh = fsg->next_buffhd_to_fill; | |
3006 | while (bh->state != BUF_STATE_EMPTY) { | |
79a7d9ee AS |
3007 | rc = sleep_thread(fsg); |
3008 | if (rc) | |
1da177e4 | 3009 | return rc; |
79a7d9ee | 3010 | } |
1da177e4 LT |
3011 | |
3012 | /* Queue a request to read a Bulk-only CBW */ | |
3013 | set_bulk_out_req_length(fsg, bh, USB_BULK_CB_WRAP_LEN); | |
70ffe6e1 | 3014 | bh->outreq->short_not_ok = 1; |
1da177e4 LT |
3015 | start_transfer(fsg, fsg->bulk_out, bh->outreq, |
3016 | &bh->outreq_busy, &bh->state); | |
3017 | ||
3018 | /* We will drain the buffer in software, which means we | |
3019 | * can reuse it for the next filling. No need to advance | |
3020 | * next_buffhd_to_fill. */ | |
3021 | ||
3022 | /* Wait for the CBW to arrive */ | |
3023 | while (bh->state != BUF_STATE_FULL) { | |
79a7d9ee AS |
3024 | rc = sleep_thread(fsg); |
3025 | if (rc) | |
1da177e4 | 3026 | return rc; |
79a7d9ee | 3027 | } |
a21d4fed | 3028 | smp_rmb(); |
1da177e4 LT |
3029 | rc = received_cbw(fsg, bh); |
3030 | bh->state = BUF_STATE_EMPTY; | |
3031 | ||
3032 | } else { // USB_PR_CB or USB_PR_CBI | |
3033 | ||
3034 | /* Wait for the next command to arrive */ | |
3035 | while (fsg->cbbuf_cmnd_size == 0) { | |
79a7d9ee AS |
3036 | rc = sleep_thread(fsg); |
3037 | if (rc) | |
1da177e4 | 3038 | return rc; |
79a7d9ee | 3039 | } |
1da177e4 LT |
3040 | |
3041 | /* Is the previous status interrupt request still busy? | |
3042 | * The host is allowed to skip reading the status, | |
3043 | * so we must cancel it. */ | |
3044 | if (fsg->intreq_busy) | |
3045 | usb_ep_dequeue(fsg->intr_in, fsg->intreq); | |
3046 | ||
3047 | /* Copy the command and mark the buffer empty */ | |
3048 | fsg->data_dir = DATA_DIR_UNKNOWN; | |
3049 | spin_lock_irq(&fsg->lock); | |
3050 | fsg->cmnd_size = fsg->cbbuf_cmnd_size; | |
3051 | memcpy(fsg->cmnd, fsg->cbbuf_cmnd, fsg->cmnd_size); | |
3052 | fsg->cbbuf_cmnd_size = 0; | |
3053 | spin_unlock_irq(&fsg->lock); | |
3054 | } | |
3055 | return rc; | |
3056 | } | |
3057 | ||
3058 | ||
3059 | /*-------------------------------------------------------------------------*/ | |
3060 | ||
3061 | static int enable_endpoint(struct fsg_dev *fsg, struct usb_ep *ep, | |
3062 | const struct usb_endpoint_descriptor *d) | |
3063 | { | |
3064 | int rc; | |
3065 | ||
3066 | ep->driver_data = fsg; | |
3067 | rc = usb_ep_enable(ep, d); | |
3068 | if (rc) | |
3069 | ERROR(fsg, "can't enable %s, result %d\n", ep->name, rc); | |
3070 | return rc; | |
3071 | } | |
3072 | ||
3073 | static int alloc_request(struct fsg_dev *fsg, struct usb_ep *ep, | |
3074 | struct usb_request **preq) | |
3075 | { | |
3076 | *preq = usb_ep_alloc_request(ep, GFP_ATOMIC); | |
3077 | if (*preq) | |
3078 | return 0; | |
3079 | ERROR(fsg, "can't allocate request for %s\n", ep->name); | |
3080 | return -ENOMEM; | |
3081 | } | |
3082 | ||
3083 | /* | |
3084 | * Reset interface setting and re-init endpoint state (toggle etc). | |
3085 | * Call with altsetting < 0 to disable the interface. The only other | |
3086 | * available altsetting is 0, which enables the interface. | |
3087 | */ | |
3088 | static int do_set_interface(struct fsg_dev *fsg, int altsetting) | |
3089 | { | |
3090 | int rc = 0; | |
3091 | int i; | |
3092 | const struct usb_endpoint_descriptor *d; | |
3093 | ||
3094 | if (fsg->running) | |
3095 | DBG(fsg, "reset interface\n"); | |
3096 | ||
3097 | reset: | |
3098 | /* Deallocate the requests */ | |
3099 | for (i = 0; i < NUM_BUFFERS; ++i) { | |
3100 | struct fsg_buffhd *bh = &fsg->buffhds[i]; | |
3101 | ||
3102 | if (bh->inreq) { | |
3103 | usb_ep_free_request(fsg->bulk_in, bh->inreq); | |
3104 | bh->inreq = NULL; | |
3105 | } | |
3106 | if (bh->outreq) { | |
3107 | usb_ep_free_request(fsg->bulk_out, bh->outreq); | |
3108 | bh->outreq = NULL; | |
3109 | } | |
3110 | } | |
3111 | if (fsg->intreq) { | |
3112 | usb_ep_free_request(fsg->intr_in, fsg->intreq); | |
3113 | fsg->intreq = NULL; | |
3114 | } | |
3115 | ||
3116 | /* Disable the endpoints */ | |
3117 | if (fsg->bulk_in_enabled) { | |
3118 | usb_ep_disable(fsg->bulk_in); | |
3119 | fsg->bulk_in_enabled = 0; | |
3120 | } | |
3121 | if (fsg->bulk_out_enabled) { | |
3122 | usb_ep_disable(fsg->bulk_out); | |
3123 | fsg->bulk_out_enabled = 0; | |
3124 | } | |
3125 | if (fsg->intr_in_enabled) { | |
3126 | usb_ep_disable(fsg->intr_in); | |
3127 | fsg->intr_in_enabled = 0; | |
3128 | } | |
3129 | ||
3130 | fsg->running = 0; | |
3131 | if (altsetting < 0 || rc != 0) | |
3132 | return rc; | |
3133 | ||
3134 | DBG(fsg, "set interface %d\n", altsetting); | |
3135 | ||
3136 | /* Enable the endpoints */ | |
3137 | d = ep_desc(fsg->gadget, &fs_bulk_in_desc, &hs_bulk_in_desc); | |
3138 | if ((rc = enable_endpoint(fsg, fsg->bulk_in, d)) != 0) | |
3139 | goto reset; | |
3140 | fsg->bulk_in_enabled = 1; | |
3141 | ||
3142 | d = ep_desc(fsg->gadget, &fs_bulk_out_desc, &hs_bulk_out_desc); | |
3143 | if ((rc = enable_endpoint(fsg, fsg->bulk_out, d)) != 0) | |
3144 | goto reset; | |
3145 | fsg->bulk_out_enabled = 1; | |
3146 | fsg->bulk_out_maxpacket = le16_to_cpu(d->wMaxPacketSize); | |
3147 | ||
3148 | if (transport_is_cbi()) { | |
3149 | d = ep_desc(fsg->gadget, &fs_intr_in_desc, &hs_intr_in_desc); | |
3150 | if ((rc = enable_endpoint(fsg, fsg->intr_in, d)) != 0) | |
3151 | goto reset; | |
3152 | fsg->intr_in_enabled = 1; | |
3153 | } | |
3154 | ||
3155 | /* Allocate the requests */ | |
3156 | for (i = 0; i < NUM_BUFFERS; ++i) { | |
3157 | struct fsg_buffhd *bh = &fsg->buffhds[i]; | |
3158 | ||
3159 | if ((rc = alloc_request(fsg, fsg->bulk_in, &bh->inreq)) != 0) | |
3160 | goto reset; | |
3161 | if ((rc = alloc_request(fsg, fsg->bulk_out, &bh->outreq)) != 0) | |
3162 | goto reset; | |
3163 | bh->inreq->buf = bh->outreq->buf = bh->buf; | |
1da177e4 LT |
3164 | bh->inreq->context = bh->outreq->context = bh; |
3165 | bh->inreq->complete = bulk_in_complete; | |
3166 | bh->outreq->complete = bulk_out_complete; | |
3167 | } | |
3168 | if (transport_is_cbi()) { | |
3169 | if ((rc = alloc_request(fsg, fsg->intr_in, &fsg->intreq)) != 0) | |
3170 | goto reset; | |
3171 | fsg->intreq->complete = intr_in_complete; | |
3172 | } | |
3173 | ||
3174 | fsg->running = 1; | |
3175 | for (i = 0; i < fsg->nluns; ++i) | |
3176 | fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED; | |
3177 | return rc; | |
3178 | } | |
3179 | ||
3180 | ||
3181 | /* | |
3182 | * Change our operational configuration. This code must agree with the code | |
3183 | * that returns config descriptors, and with interface altsetting code. | |
3184 | * | |
3185 | * It's also responsible for power management interactions. Some | |
3186 | * configurations might not work with our current power sources. | |
3187 | * For now we just assume the gadget is always self-powered. | |
3188 | */ | |
3189 | static int do_set_config(struct fsg_dev *fsg, u8 new_config) | |
3190 | { | |
3191 | int rc = 0; | |
3192 | ||
3193 | /* Disable the single interface */ | |
3194 | if (fsg->config != 0) { | |
3195 | DBG(fsg, "reset config\n"); | |
3196 | fsg->config = 0; | |
3197 | rc = do_set_interface(fsg, -1); | |
3198 | } | |
3199 | ||
3200 | /* Enable the interface */ | |
3201 | if (new_config != 0) { | |
3202 | fsg->config = new_config; | |
3203 | if ((rc = do_set_interface(fsg, 0)) != 0) | |
3204 | fsg->config = 0; // Reset on errors | |
3205 | else { | |
3206 | char *speed; | |
3207 | ||
3208 | switch (fsg->gadget->speed) { | |
3209 | case USB_SPEED_LOW: speed = "low"; break; | |
3210 | case USB_SPEED_FULL: speed = "full"; break; | |
3211 | case USB_SPEED_HIGH: speed = "high"; break; | |
3212 | default: speed = "?"; break; | |
3213 | } | |
3214 | INFO(fsg, "%s speed config #%d\n", speed, fsg->config); | |
3215 | } | |
3216 | } | |
3217 | return rc; | |
3218 | } | |
3219 | ||
3220 | ||
3221 | /*-------------------------------------------------------------------------*/ | |
3222 | ||
3223 | static void handle_exception(struct fsg_dev *fsg) | |
3224 | { | |
3225 | siginfo_t info; | |
3226 | int sig; | |
3227 | int i; | |
3228 | int num_active; | |
3229 | struct fsg_buffhd *bh; | |
3230 | enum fsg_state old_state; | |
3231 | u8 new_config; | |
3232 | struct lun *curlun; | |
3233 | unsigned int exception_req_tag; | |
3234 | int rc; | |
3235 | ||
3236 | /* Clear the existing signals. Anything but SIGUSR1 is converted | |
3237 | * into a high-priority EXIT exception. */ | |
3238 | for (;;) { | |
8cfbe7e6 | 3239 | sig = dequeue_signal_lock(current, ¤t->blocked, &info); |
1da177e4 LT |
3240 | if (!sig) |
3241 | break; | |
3242 | if (sig != SIGUSR1) { | |
3243 | if (fsg->state < FSG_STATE_EXIT) | |
3244 | DBG(fsg, "Main thread exiting on signal\n"); | |
3245 | raise_exception(fsg, FSG_STATE_EXIT); | |
3246 | } | |
3247 | } | |
3248 | ||
3249 | /* Cancel all the pending transfers */ | |
3250 | if (fsg->intreq_busy) | |
3251 | usb_ep_dequeue(fsg->intr_in, fsg->intreq); | |
3252 | for (i = 0; i < NUM_BUFFERS; ++i) { | |
3253 | bh = &fsg->buffhds[i]; | |
3254 | if (bh->inreq_busy) | |
3255 | usb_ep_dequeue(fsg->bulk_in, bh->inreq); | |
3256 | if (bh->outreq_busy) | |
3257 | usb_ep_dequeue(fsg->bulk_out, bh->outreq); | |
3258 | } | |
3259 | ||
3260 | /* Wait until everything is idle */ | |
3261 | for (;;) { | |
3262 | num_active = fsg->intreq_busy; | |
3263 | for (i = 0; i < NUM_BUFFERS; ++i) { | |
3264 | bh = &fsg->buffhds[i]; | |
3265 | num_active += bh->inreq_busy + bh->outreq_busy; | |
3266 | } | |
3267 | if (num_active == 0) | |
3268 | break; | |
3269 | if (sleep_thread(fsg)) | |
3270 | return; | |
3271 | } | |
3272 | ||
3273 | /* Clear out the controller's fifos */ | |
3274 | if (fsg->bulk_in_enabled) | |
3275 | usb_ep_fifo_flush(fsg->bulk_in); | |
3276 | if (fsg->bulk_out_enabled) | |
3277 | usb_ep_fifo_flush(fsg->bulk_out); | |
3278 | if (fsg->intr_in_enabled) | |
3279 | usb_ep_fifo_flush(fsg->intr_in); | |
3280 | ||
3281 | /* Reset the I/O buffer states and pointers, the SCSI | |
3282 | * state, and the exception. Then invoke the handler. */ | |
3283 | spin_lock_irq(&fsg->lock); | |
3284 | ||
3285 | for (i = 0; i < NUM_BUFFERS; ++i) { | |
3286 | bh = &fsg->buffhds[i]; | |
3287 | bh->state = BUF_STATE_EMPTY; | |
3288 | } | |
3289 | fsg->next_buffhd_to_fill = fsg->next_buffhd_to_drain = | |
3290 | &fsg->buffhds[0]; | |
3291 | ||
3292 | exception_req_tag = fsg->exception_req_tag; | |
3293 | new_config = fsg->new_config; | |
3294 | old_state = fsg->state; | |
3295 | ||
3296 | if (old_state == FSG_STATE_ABORT_BULK_OUT) | |
3297 | fsg->state = FSG_STATE_STATUS_PHASE; | |
3298 | else { | |
3299 | for (i = 0; i < fsg->nluns; ++i) { | |
3300 | curlun = &fsg->luns[i]; | |
3301 | curlun->prevent_medium_removal = 0; | |
3302 | curlun->sense_data = curlun->unit_attention_data = | |
3303 | SS_NO_SENSE; | |
3304 | curlun->sense_data_info = 0; | |
6174d0fd | 3305 | curlun->info_valid = 0; |
1da177e4 LT |
3306 | } |
3307 | fsg->state = FSG_STATE_IDLE; | |
3308 | } | |
3309 | spin_unlock_irq(&fsg->lock); | |
3310 | ||
3311 | /* Carry out any extra actions required for the exception */ | |
3312 | switch (old_state) { | |
3313 | default: | |
3314 | break; | |
3315 | ||
3316 | case FSG_STATE_ABORT_BULK_OUT: | |
3317 | send_status(fsg); | |
3318 | spin_lock_irq(&fsg->lock); | |
3319 | if (fsg->state == FSG_STATE_STATUS_PHASE) | |
3320 | fsg->state = FSG_STATE_IDLE; | |
3321 | spin_unlock_irq(&fsg->lock); | |
3322 | break; | |
3323 | ||
3324 | case FSG_STATE_RESET: | |
3325 | /* In case we were forced against our will to halt a | |
3326 | * bulk endpoint, clear the halt now. (The SuperH UDC | |
3327 | * requires this.) */ | |
3328 | if (test_and_clear_bit(CLEAR_BULK_HALTS, | |
3329 | &fsg->atomic_bitflags)) { | |
3330 | usb_ep_clear_halt(fsg->bulk_in); | |
3331 | usb_ep_clear_halt(fsg->bulk_out); | |
3332 | } | |
3333 | ||
3334 | if (transport_is_bbb()) { | |
3335 | if (fsg->ep0_req_tag == exception_req_tag) | |
3336 | ep0_queue(fsg); // Complete the status stage | |
3337 | ||
3338 | } else if (transport_is_cbi()) | |
3339 | send_status(fsg); // Status by interrupt pipe | |
3340 | ||
3341 | /* Technically this should go here, but it would only be | |
3342 | * a waste of time. Ditto for the INTERFACE_CHANGE and | |
3343 | * CONFIG_CHANGE cases. */ | |
3344 | // for (i = 0; i < fsg->nluns; ++i) | |
3345 | // fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED; | |
3346 | break; | |
3347 | ||
3348 | case FSG_STATE_INTERFACE_CHANGE: | |
3349 | rc = do_set_interface(fsg, 0); | |
3350 | if (fsg->ep0_req_tag != exception_req_tag) | |
3351 | break; | |
3352 | if (rc != 0) // STALL on errors | |
3353 | fsg_set_halt(fsg, fsg->ep0); | |
3354 | else // Complete the status stage | |
3355 | ep0_queue(fsg); | |
3356 | break; | |
3357 | ||
3358 | case FSG_STATE_CONFIG_CHANGE: | |
3359 | rc = do_set_config(fsg, new_config); | |
3360 | if (fsg->ep0_req_tag != exception_req_tag) | |
3361 | break; | |
3362 | if (rc != 0) // STALL on errors | |
3363 | fsg_set_halt(fsg, fsg->ep0); | |
3364 | else // Complete the status stage | |
3365 | ep0_queue(fsg); | |
3366 | break; | |
3367 | ||
3368 | case FSG_STATE_DISCONNECT: | |
3369 | fsync_all(fsg); | |
3370 | do_set_config(fsg, 0); // Unconfigured state | |
3371 | break; | |
3372 | ||
3373 | case FSG_STATE_EXIT: | |
3374 | case FSG_STATE_TERMINATED: | |
3375 | do_set_config(fsg, 0); // Free resources | |
3376 | spin_lock_irq(&fsg->lock); | |
3377 | fsg->state = FSG_STATE_TERMINATED; // Stop the thread | |
3378 | spin_unlock_irq(&fsg->lock); | |
3379 | break; | |
3380 | } | |
3381 | } | |
3382 | ||
3383 | ||
3384 | /*-------------------------------------------------------------------------*/ | |
3385 | ||
3386 | static int fsg_main_thread(void *fsg_) | |
3387 | { | |
7ca46b86 | 3388 | struct fsg_dev *fsg = fsg_; |
1da177e4 | 3389 | |
1da177e4 LT |
3390 | /* Allow the thread to be killed by a signal, but set the signal mask |
3391 | * to block everything but INT, TERM, KILL, and USR1. */ | |
8cfbe7e6 ON |
3392 | allow_signal(SIGINT); |
3393 | allow_signal(SIGTERM); | |
3394 | allow_signal(SIGKILL); | |
3395 | allow_signal(SIGUSR1); | |
1da177e4 | 3396 | |
83144186 RW |
3397 | /* Allow the thread to be frozen */ |
3398 | set_freezable(); | |
3399 | ||
1da177e4 LT |
3400 | /* Arrange for userspace references to be interpreted as kernel |
3401 | * pointers. That way we can pass a kernel pointer to a routine | |
3402 | * that expects a __user pointer and it will work okay. */ | |
3403 | set_fs(get_ds()); | |
3404 | ||
1da177e4 LT |
3405 | /* The main loop */ |
3406 | while (fsg->state != FSG_STATE_TERMINATED) { | |
3407 | if (exception_in_progress(fsg) || signal_pending(current)) { | |
3408 | handle_exception(fsg); | |
3409 | continue; | |
3410 | } | |
3411 | ||
3412 | if (!fsg->running) { | |
3413 | sleep_thread(fsg); | |
3414 | continue; | |
3415 | } | |
3416 | ||
3417 | if (get_next_command(fsg)) | |
3418 | continue; | |
3419 | ||
3420 | spin_lock_irq(&fsg->lock); | |
3421 | if (!exception_in_progress(fsg)) | |
3422 | fsg->state = FSG_STATE_DATA_PHASE; | |
3423 | spin_unlock_irq(&fsg->lock); | |
3424 | ||
3425 | if (do_scsi_command(fsg) || finish_reply(fsg)) | |
3426 | continue; | |
3427 | ||
3428 | spin_lock_irq(&fsg->lock); | |
3429 | if (!exception_in_progress(fsg)) | |
3430 | fsg->state = FSG_STATE_STATUS_PHASE; | |
3431 | spin_unlock_irq(&fsg->lock); | |
3432 | ||
3433 | if (send_status(fsg)) | |
3434 | continue; | |
3435 | ||
3436 | spin_lock_irq(&fsg->lock); | |
3437 | if (!exception_in_progress(fsg)) | |
3438 | fsg->state = FSG_STATE_IDLE; | |
3439 | spin_unlock_irq(&fsg->lock); | |
3440 | } | |
3441 | ||
22efcf4a | 3442 | spin_lock_irq(&fsg->lock); |
1da177e4 | 3443 | fsg->thread_task = NULL; |
22efcf4a | 3444 | spin_unlock_irq(&fsg->lock); |
1da177e4 LT |
3445 | |
3446 | /* In case we are exiting because of a signal, unregister the | |
3447 | * gadget driver and close the backing file. */ | |
3448 | if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags)) { | |
3449 | usb_gadget_unregister_driver(&fsg_driver); | |
3450 | close_all_backing_files(fsg); | |
3451 | } | |
3452 | ||
3453 | /* Let the unbind and cleanup routines know the thread has exited */ | |
3454 | complete_and_exit(&fsg->thread_notifier, 0); | |
3455 | } | |
3456 | ||
3457 | ||
3458 | /*-------------------------------------------------------------------------*/ | |
3459 | ||
3460 | /* If the next two routines are called while the gadget is registered, | |
3461 | * the caller must own fsg->filesem for writing. */ | |
3462 | ||
3463 | static int open_backing_file(struct lun *curlun, const char *filename) | |
3464 | { | |
3465 | int ro; | |
3466 | struct file *filp = NULL; | |
3467 | int rc = -EINVAL; | |
3468 | struct inode *inode = NULL; | |
3469 | loff_t size; | |
3470 | loff_t num_sectors; | |
3471 | ||
3472 | /* R/W if we can, R/O if we must */ | |
3473 | ro = curlun->ro; | |
3474 | if (!ro) { | |
3475 | filp = filp_open(filename, O_RDWR | O_LARGEFILE, 0); | |
3476 | if (-EROFS == PTR_ERR(filp)) | |
3477 | ro = 1; | |
3478 | } | |
3479 | if (ro) | |
3480 | filp = filp_open(filename, O_RDONLY | O_LARGEFILE, 0); | |
3481 | if (IS_ERR(filp)) { | |
3482 | LINFO(curlun, "unable to open backing file: %s\n", filename); | |
3483 | return PTR_ERR(filp); | |
3484 | } | |
3485 | ||
3486 | if (!(filp->f_mode & FMODE_WRITE)) | |
3487 | ro = 1; | |
3488 | ||
33cb8994 JS |
3489 | if (filp->f_path.dentry) |
3490 | inode = filp->f_path.dentry->d_inode; | |
1da177e4 LT |
3491 | if (inode && S_ISBLK(inode->i_mode)) { |
3492 | if (bdev_read_only(inode->i_bdev)) | |
3493 | ro = 1; | |
3494 | } else if (!inode || !S_ISREG(inode->i_mode)) { | |
3495 | LINFO(curlun, "invalid file type: %s\n", filename); | |
3496 | goto out; | |
3497 | } | |
3498 | ||
3499 | /* If we can't read the file, it's no good. | |
3500 | * If we can't write the file, use it read-only. */ | |
3501 | if (!filp->f_op || !(filp->f_op->read || filp->f_op->aio_read)) { | |
3502 | LINFO(curlun, "file not readable: %s\n", filename); | |
3503 | goto out; | |
3504 | } | |
3505 | if (!(filp->f_op->write || filp->f_op->aio_write)) | |
3506 | ro = 1; | |
3507 | ||
3508 | size = i_size_read(inode->i_mapping->host); | |
3509 | if (size < 0) { | |
3510 | LINFO(curlun, "unable to find file size: %s\n", filename); | |
3511 | rc = (int) size; | |
3512 | goto out; | |
3513 | } | |
3514 | num_sectors = size >> 9; // File size in 512-byte sectors | |
3515 | if (num_sectors == 0) { | |
3516 | LINFO(curlun, "file too small: %s\n", filename); | |
3517 | rc = -ETOOSMALL; | |
3518 | goto out; | |
3519 | } | |
3520 | ||
3521 | get_file(filp); | |
3522 | curlun->ro = ro; | |
3523 | curlun->filp = filp; | |
3524 | curlun->file_length = size; | |
3525 | curlun->num_sectors = num_sectors; | |
3526 | LDBG(curlun, "open backing file: %s\n", filename); | |
3527 | rc = 0; | |
3528 | ||
3529 | out: | |
3530 | filp_close(filp, current->files); | |
3531 | return rc; | |
3532 | } | |
3533 | ||
3534 | ||
3535 | static void close_backing_file(struct lun *curlun) | |
3536 | { | |
3537 | if (curlun->filp) { | |
3538 | LDBG(curlun, "close backing file\n"); | |
3539 | fput(curlun->filp); | |
3540 | curlun->filp = NULL; | |
3541 | } | |
3542 | } | |
3543 | ||
3544 | static void close_all_backing_files(struct fsg_dev *fsg) | |
3545 | { | |
3546 | int i; | |
3547 | ||
3548 | for (i = 0; i < fsg->nluns; ++i) | |
3549 | close_backing_file(&fsg->luns[i]); | |
3550 | } | |
3551 | ||
3552 | ||
10523b3b | 3553 | static ssize_t show_ro(struct device *dev, struct device_attribute *attr, char *buf) |
1da177e4 LT |
3554 | { |
3555 | struct lun *curlun = dev_to_lun(dev); | |
3556 | ||
3557 | return sprintf(buf, "%d\n", curlun->ro); | |
3558 | } | |
3559 | ||
79a7d9ee AS |
3560 | static ssize_t show_file(struct device *dev, struct device_attribute *attr, |
3561 | char *buf) | |
1da177e4 LT |
3562 | { |
3563 | struct lun *curlun = dev_to_lun(dev); | |
7ca46b86 | 3564 | struct fsg_dev *fsg = dev_get_drvdata(dev); |
1da177e4 LT |
3565 | char *p; |
3566 | ssize_t rc; | |
3567 | ||
3568 | down_read(&fsg->filesem); | |
3569 | if (backing_file_is_open(curlun)) { // Get the complete pathname | |
79a7d9ee AS |
3570 | p = d_path(curlun->filp->f_path.dentry, |
3571 | curlun->filp->f_path.mnt, buf, PAGE_SIZE - 1); | |
1da177e4 LT |
3572 | if (IS_ERR(p)) |
3573 | rc = PTR_ERR(p); | |
3574 | else { | |
3575 | rc = strlen(p); | |
3576 | memmove(buf, p, rc); | |
3577 | buf[rc] = '\n'; // Add a newline | |
3578 | buf[++rc] = 0; | |
3579 | } | |
3580 | } else { // No file, return 0 bytes | |
3581 | *buf = 0; | |
3582 | rc = 0; | |
3583 | } | |
3584 | up_read(&fsg->filesem); | |
3585 | return rc; | |
3586 | } | |
3587 | ||
3588 | ||
79a7d9ee AS |
3589 | static ssize_t store_ro(struct device *dev, struct device_attribute *attr, |
3590 | const char *buf, size_t count) | |
1da177e4 LT |
3591 | { |
3592 | ssize_t rc = count; | |
3593 | struct lun *curlun = dev_to_lun(dev); | |
7ca46b86 | 3594 | struct fsg_dev *fsg = dev_get_drvdata(dev); |
1da177e4 LT |
3595 | int i; |
3596 | ||
3597 | if (sscanf(buf, "%d", &i) != 1) | |
3598 | return -EINVAL; | |
3599 | ||
3600 | /* Allow the write-enable status to change only while the backing file | |
3601 | * is closed. */ | |
3602 | down_read(&fsg->filesem); | |
3603 | if (backing_file_is_open(curlun)) { | |
3604 | LDBG(curlun, "read-only status change prevented\n"); | |
3605 | rc = -EBUSY; | |
3606 | } else { | |
3607 | curlun->ro = !!i; | |
3608 | LDBG(curlun, "read-only status set to %d\n", curlun->ro); | |
3609 | } | |
3610 | up_read(&fsg->filesem); | |
3611 | return rc; | |
3612 | } | |
3613 | ||
79a7d9ee AS |
3614 | static ssize_t store_file(struct device *dev, struct device_attribute *attr, |
3615 | const char *buf, size_t count) | |
1da177e4 LT |
3616 | { |
3617 | struct lun *curlun = dev_to_lun(dev); | |
7ca46b86 | 3618 | struct fsg_dev *fsg = dev_get_drvdata(dev); |
1da177e4 LT |
3619 | int rc = 0; |
3620 | ||
3621 | if (curlun->prevent_medium_removal && backing_file_is_open(curlun)) { | |
3622 | LDBG(curlun, "eject attempt prevented\n"); | |
3623 | return -EBUSY; // "Door is locked" | |
3624 | } | |
3625 | ||
3626 | /* Remove a trailing newline */ | |
3627 | if (count > 0 && buf[count-1] == '\n') | |
3628 | ((char *) buf)[count-1] = 0; // Ugh! | |
3629 | ||
3630 | /* Eject current medium */ | |
3631 | down_write(&fsg->filesem); | |
3632 | if (backing_file_is_open(curlun)) { | |
3633 | close_backing_file(curlun); | |
3634 | curlun->unit_attention_data = SS_MEDIUM_NOT_PRESENT; | |
3635 | } | |
3636 | ||
3637 | /* Load new medium */ | |
3638 | if (count > 0 && buf[0]) { | |
3639 | rc = open_backing_file(curlun, buf); | |
3640 | if (rc == 0) | |
3641 | curlun->unit_attention_data = | |
3642 | SS_NOT_READY_TO_READY_TRANSITION; | |
3643 | } | |
3644 | up_write(&fsg->filesem); | |
3645 | return (rc < 0 ? rc : count); | |
3646 | } | |
3647 | ||
3648 | ||
3649 | /* The write permissions and store_xxx pointers are set in fsg_bind() */ | |
3650 | static DEVICE_ATTR(ro, 0444, show_ro, NULL); | |
3651 | static DEVICE_ATTR(file, 0444, show_file, NULL); | |
3652 | ||
3653 | ||
3654 | /*-------------------------------------------------------------------------*/ | |
3655 | ||
87c4252a AS |
3656 | static void fsg_release(struct kref *ref) |
3657 | { | |
3658 | struct fsg_dev *fsg = container_of(ref, struct fsg_dev, ref); | |
3659 | ||
3660 | kfree(fsg->luns); | |
3661 | kfree(fsg); | |
3662 | } | |
3663 | ||
1da177e4 LT |
3664 | static void lun_release(struct device *dev) |
3665 | { | |
7ca46b86 | 3666 | struct fsg_dev *fsg = dev_get_drvdata(dev); |
1da177e4 | 3667 | |
87c4252a | 3668 | kref_put(&fsg->ref, fsg_release); |
1da177e4 LT |
3669 | } |
3670 | ||
a353678d | 3671 | static void /* __init_or_exit */ fsg_unbind(struct usb_gadget *gadget) |
1da177e4 LT |
3672 | { |
3673 | struct fsg_dev *fsg = get_gadget_data(gadget); | |
3674 | int i; | |
3675 | struct lun *curlun; | |
3676 | struct usb_request *req = fsg->ep0req; | |
3677 | ||
3678 | DBG(fsg, "unbind\n"); | |
3679 | clear_bit(REGISTERED, &fsg->atomic_bitflags); | |
3680 | ||
3681 | /* Unregister the sysfs attribute files and the LUNs */ | |
1da177e4 LT |
3682 | for (i = 0; i < fsg->nluns; ++i) { |
3683 | curlun = &fsg->luns[i]; | |
3684 | if (curlun->registered) { | |
3685 | device_remove_file(&curlun->dev, &dev_attr_ro); | |
3686 | device_remove_file(&curlun->dev, &dev_attr_file); | |
3687 | device_unregister(&curlun->dev); | |
1da177e4 LT |
3688 | curlun->registered = 0; |
3689 | } | |
3690 | } | |
3691 | ||
3692 | /* If the thread isn't already dead, tell it to exit now */ | |
3693 | if (fsg->state != FSG_STATE_TERMINATED) { | |
3694 | raise_exception(fsg, FSG_STATE_EXIT); | |
3695 | wait_for_completion(&fsg->thread_notifier); | |
3696 | ||
3697 | /* The cleanup routine waits for this completion also */ | |
3698 | complete(&fsg->thread_notifier); | |
3699 | } | |
3700 | ||
3701 | /* Free the data buffers */ | |
9d8bab58 DB |
3702 | for (i = 0; i < NUM_BUFFERS; ++i) |
3703 | kfree(fsg->buffhds[i].buf); | |
1da177e4 LT |
3704 | |
3705 | /* Free the request and buffer for endpoint 0 */ | |
3706 | if (req) { | |
9d8bab58 | 3707 | kfree(req->buf); |
1da177e4 LT |
3708 | usb_ep_free_request(fsg->ep0, req); |
3709 | } | |
3710 | ||
3711 | set_gadget_data(gadget, NULL); | |
3712 | } | |
3713 | ||
3714 | ||
3715 | static int __init check_parameters(struct fsg_dev *fsg) | |
3716 | { | |
3717 | int prot; | |
91e79c91 | 3718 | int gcnum; |
1da177e4 LT |
3719 | |
3720 | /* Store the default values */ | |
3721 | mod_data.transport_type = USB_PR_BULK; | |
3722 | mod_data.transport_name = "Bulk-only"; | |
3723 | mod_data.protocol_type = USB_SC_SCSI; | |
3724 | mod_data.protocol_name = "Transparent SCSI"; | |
3725 | ||
3726 | if (gadget_is_sh(fsg->gadget)) | |
3727 | mod_data.can_stall = 0; | |
3728 | ||
3729 | if (mod_data.release == 0xffff) { // Parameter wasn't set | |
1da177e4 | 3730 | /* The sa1100 controller is not supported */ |
91e79c91 DB |
3731 | if (gadget_is_sa1100(fsg->gadget)) |
3732 | gcnum = -1; | |
3733 | else | |
3734 | gcnum = usb_gadget_controller_number(fsg->gadget); | |
3735 | if (gcnum >= 0) | |
3736 | mod_data.release = 0x0300 + gcnum; | |
1da177e4 LT |
3737 | else { |
3738 | WARN(fsg, "controller '%s' not recognized\n", | |
3739 | fsg->gadget->name); | |
3740 | mod_data.release = 0x0399; | |
3741 | } | |
3742 | } | |
3743 | ||
3744 | prot = simple_strtol(mod_data.protocol_parm, NULL, 0); | |
3745 | ||
3746 | #ifdef CONFIG_USB_FILE_STORAGE_TEST | |
3747 | if (strnicmp(mod_data.transport_parm, "BBB", 10) == 0) { | |
3748 | ; // Use default setting | |
3749 | } else if (strnicmp(mod_data.transport_parm, "CB", 10) == 0) { | |
3750 | mod_data.transport_type = USB_PR_CB; | |
3751 | mod_data.transport_name = "Control-Bulk"; | |
3752 | } else if (strnicmp(mod_data.transport_parm, "CBI", 10) == 0) { | |
3753 | mod_data.transport_type = USB_PR_CBI; | |
3754 | mod_data.transport_name = "Control-Bulk-Interrupt"; | |
3755 | } else { | |
3756 | ERROR(fsg, "invalid transport: %s\n", mod_data.transport_parm); | |
3757 | return -EINVAL; | |
3758 | } | |
3759 | ||
3760 | if (strnicmp(mod_data.protocol_parm, "SCSI", 10) == 0 || | |
3761 | prot == USB_SC_SCSI) { | |
3762 | ; // Use default setting | |
3763 | } else if (strnicmp(mod_data.protocol_parm, "RBC", 10) == 0 || | |
3764 | prot == USB_SC_RBC) { | |
3765 | mod_data.protocol_type = USB_SC_RBC; | |
3766 | mod_data.protocol_name = "RBC"; | |
3767 | } else if (strnicmp(mod_data.protocol_parm, "8020", 4) == 0 || | |
3768 | strnicmp(mod_data.protocol_parm, "ATAPI", 10) == 0 || | |
3769 | prot == USB_SC_8020) { | |
3770 | mod_data.protocol_type = USB_SC_8020; | |
3771 | mod_data.protocol_name = "8020i (ATAPI)"; | |
3772 | } else if (strnicmp(mod_data.protocol_parm, "QIC", 3) == 0 || | |
3773 | prot == USB_SC_QIC) { | |
3774 | mod_data.protocol_type = USB_SC_QIC; | |
3775 | mod_data.protocol_name = "QIC-157"; | |
3776 | } else if (strnicmp(mod_data.protocol_parm, "UFI", 10) == 0 || | |
3777 | prot == USB_SC_UFI) { | |
3778 | mod_data.protocol_type = USB_SC_UFI; | |
3779 | mod_data.protocol_name = "UFI"; | |
3780 | } else if (strnicmp(mod_data.protocol_parm, "8070", 4) == 0 || | |
3781 | prot == USB_SC_8070) { | |
3782 | mod_data.protocol_type = USB_SC_8070; | |
3783 | mod_data.protocol_name = "8070i"; | |
3784 | } else { | |
3785 | ERROR(fsg, "invalid protocol: %s\n", mod_data.protocol_parm); | |
3786 | return -EINVAL; | |
3787 | } | |
3788 | ||
3789 | mod_data.buflen &= PAGE_CACHE_MASK; | |
3790 | if (mod_data.buflen <= 0) { | |
3791 | ERROR(fsg, "invalid buflen\n"); | |
3792 | return -ETOOSMALL; | |
3793 | } | |
3794 | #endif /* CONFIG_USB_FILE_STORAGE_TEST */ | |
3795 | ||
3796 | return 0; | |
3797 | } | |
3798 | ||
3799 | ||
3800 | static int __init fsg_bind(struct usb_gadget *gadget) | |
3801 | { | |
3802 | struct fsg_dev *fsg = the_fsg; | |
3803 | int rc; | |
3804 | int i; | |
3805 | struct lun *curlun; | |
3806 | struct usb_ep *ep; | |
3807 | struct usb_request *req; | |
3808 | char *pathbuf, *p; | |
3809 | ||
3810 | fsg->gadget = gadget; | |
3811 | set_gadget_data(gadget, fsg); | |
3812 | fsg->ep0 = gadget->ep0; | |
3813 | fsg->ep0->driver_data = fsg; | |
3814 | ||
3815 | if ((rc = check_parameters(fsg)) != 0) | |
3816 | goto out; | |
3817 | ||
3818 | if (mod_data.removable) { // Enable the store_xxx attributes | |
3819 | dev_attr_ro.attr.mode = dev_attr_file.attr.mode = 0644; | |
3820 | dev_attr_ro.store = store_ro; | |
3821 | dev_attr_file.store = store_file; | |
3822 | } | |
3823 | ||
3824 | /* Find out how many LUNs there should be */ | |
3825 | i = mod_data.nluns; | |
3826 | if (i == 0) | |
2e806f67 | 3827 | i = max(mod_data.num_filenames, 1u); |
1da177e4 LT |
3828 | if (i > MAX_LUNS) { |
3829 | ERROR(fsg, "invalid number of LUNs: %d\n", i); | |
3830 | rc = -EINVAL; | |
3831 | goto out; | |
3832 | } | |
3833 | ||
3834 | /* Create the LUNs, open their backing files, and register the | |
3835 | * LUN devices in sysfs. */ | |
a922c687 | 3836 | fsg->luns = kzalloc(i * sizeof(struct lun), GFP_KERNEL); |
1da177e4 LT |
3837 | if (!fsg->luns) { |
3838 | rc = -ENOMEM; | |
3839 | goto out; | |
3840 | } | |
1da177e4 LT |
3841 | fsg->nluns = i; |
3842 | ||
3843 | for (i = 0; i < fsg->nluns; ++i) { | |
3844 | curlun = &fsg->luns[i]; | |
aafe5bd6 | 3845 | curlun->ro = mod_data.ro[i]; |
2de9eaef | 3846 | curlun->dev.release = lun_release; |
1da177e4 LT |
3847 | curlun->dev.parent = &gadget->dev; |
3848 | curlun->dev.driver = &fsg_driver.driver; | |
3849 | dev_set_drvdata(&curlun->dev, fsg); | |
3850 | snprintf(curlun->dev.bus_id, BUS_ID_SIZE, | |
3851 | "%s-lun%d", gadget->dev.bus_id, i); | |
3852 | ||
2de9eaef | 3853 | if ((rc = device_register(&curlun->dev)) != 0) { |
1da177e4 | 3854 | INFO(fsg, "failed to register LUN%d: %d\n", i, rc); |
2de9eaef AS |
3855 | goto out; |
3856 | } | |
3857 | if ((rc = device_create_file(&curlun->dev, | |
3858 | &dev_attr_ro)) != 0 || | |
3859 | (rc = device_create_file(&curlun->dev, | |
3860 | &dev_attr_file)) != 0) { | |
3861 | device_unregister(&curlun->dev); | |
3862 | goto out; | |
1da177e4 | 3863 | } |
2de9eaef AS |
3864 | curlun->registered = 1; |
3865 | kref_get(&fsg->ref); | |
1da177e4 | 3866 | |
aafe5bd6 AS |
3867 | if (mod_data.file[i] && *mod_data.file[i]) { |
3868 | if ((rc = open_backing_file(curlun, | |
3869 | mod_data.file[i])) != 0) | |
1da177e4 LT |
3870 | goto out; |
3871 | } else if (!mod_data.removable) { | |
3872 | ERROR(fsg, "no file given for LUN%d\n", i); | |
3873 | rc = -EINVAL; | |
3874 | goto out; | |
3875 | } | |
3876 | } | |
3877 | ||
3878 | /* Find all the endpoints we will use */ | |
3879 | usb_ep_autoconfig_reset(gadget); | |
3880 | ep = usb_ep_autoconfig(gadget, &fs_bulk_in_desc); | |
3881 | if (!ep) | |
3882 | goto autoconf_fail; | |
3883 | ep->driver_data = fsg; // claim the endpoint | |
3884 | fsg->bulk_in = ep; | |
3885 | ||
3886 | ep = usb_ep_autoconfig(gadget, &fs_bulk_out_desc); | |
3887 | if (!ep) | |
3888 | goto autoconf_fail; | |
3889 | ep->driver_data = fsg; // claim the endpoint | |
3890 | fsg->bulk_out = ep; | |
3891 | ||
3892 | if (transport_is_cbi()) { | |
3893 | ep = usb_ep_autoconfig(gadget, &fs_intr_in_desc); | |
3894 | if (!ep) | |
3895 | goto autoconf_fail; | |
3896 | ep->driver_data = fsg; // claim the endpoint | |
3897 | fsg->intr_in = ep; | |
3898 | } | |
3899 | ||
3900 | /* Fix up the descriptors */ | |
3901 | device_desc.bMaxPacketSize0 = fsg->ep0->maxpacket; | |
3902 | device_desc.idVendor = cpu_to_le16(mod_data.vendor); | |
3903 | device_desc.idProduct = cpu_to_le16(mod_data.product); | |
3904 | device_desc.bcdDevice = cpu_to_le16(mod_data.release); | |
3905 | ||
3906 | i = (transport_is_cbi() ? 3 : 2); // Number of endpoints | |
3907 | intf_desc.bNumEndpoints = i; | |
3908 | intf_desc.bInterfaceSubClass = mod_data.protocol_type; | |
3909 | intf_desc.bInterfaceProtocol = mod_data.transport_type; | |
3910 | fs_function[i + FS_FUNCTION_PRE_EP_ENTRIES] = NULL; | |
3911 | ||
2e806f67 DB |
3912 | if (gadget_is_dualspeed(gadget)) { |
3913 | hs_function[i + HS_FUNCTION_PRE_EP_ENTRIES] = NULL; | |
1da177e4 | 3914 | |
2e806f67 DB |
3915 | /* Assume ep0 uses the same maxpacket value for both speeds */ |
3916 | dev_qualifier.bMaxPacketSize0 = fsg->ep0->maxpacket; | |
1da177e4 | 3917 | |
2e806f67 DB |
3918 | /* Assume endpoint addresses are the same for both speeds */ |
3919 | hs_bulk_in_desc.bEndpointAddress = | |
3920 | fs_bulk_in_desc.bEndpointAddress; | |
3921 | hs_bulk_out_desc.bEndpointAddress = | |
3922 | fs_bulk_out_desc.bEndpointAddress; | |
3923 | hs_intr_in_desc.bEndpointAddress = | |
3924 | fs_intr_in_desc.bEndpointAddress; | |
3925 | } | |
1da177e4 | 3926 | |
2e806f67 | 3927 | if (gadget_is_otg(gadget)) |
02036338 | 3928 | otg_desc.bmAttributes |= USB_OTG_HNP; |
1da177e4 LT |
3929 | |
3930 | rc = -ENOMEM; | |
3931 | ||
3932 | /* Allocate the request and buffer for endpoint 0 */ | |
3933 | fsg->ep0req = req = usb_ep_alloc_request(fsg->ep0, GFP_KERNEL); | |
3934 | if (!req) | |
3935 | goto out; | |
9d8bab58 | 3936 | req->buf = kmalloc(EP0_BUFSIZE, GFP_KERNEL); |
1da177e4 LT |
3937 | if (!req->buf) |
3938 | goto out; | |
3939 | req->complete = ep0_complete; | |
3940 | ||
3941 | /* Allocate the data buffers */ | |
3942 | for (i = 0; i < NUM_BUFFERS; ++i) { | |
3943 | struct fsg_buffhd *bh = &fsg->buffhds[i]; | |
3944 | ||
14cd5f8e AS |
3945 | /* Allocate for the bulk-in endpoint. We assume that |
3946 | * the buffer will also work with the bulk-out (and | |
3947 | * interrupt-in) endpoint. */ | |
9d8bab58 | 3948 | bh->buf = kmalloc(mod_data.buflen, GFP_KERNEL); |
1da177e4 LT |
3949 | if (!bh->buf) |
3950 | goto out; | |
3951 | bh->next = bh + 1; | |
3952 | } | |
3953 | fsg->buffhds[NUM_BUFFERS - 1].next = &fsg->buffhds[0]; | |
3954 | ||
3955 | /* This should reflect the actual gadget power source */ | |
3956 | usb_gadget_set_selfpowered(gadget); | |
3957 | ||
3958 | snprintf(manufacturer, sizeof manufacturer, "%s %s with %s", | |
96b644bd | 3959 | init_utsname()->sysname, init_utsname()->release, |
1da177e4 LT |
3960 | gadget->name); |
3961 | ||
3962 | /* On a real device, serial[] would be loaded from permanent | |
3963 | * storage. We just encode it from the driver version string. */ | |
3964 | for (i = 0; i < sizeof(serial) - 2; i += 2) { | |
3965 | unsigned char c = DRIVER_VERSION[i / 2]; | |
3966 | ||
3967 | if (!c) | |
3968 | break; | |
3969 | sprintf(&serial[i], "%02X", c); | |
3970 | } | |
3971 | ||
22efcf4a AS |
3972 | fsg->thread_task = kthread_create(fsg_main_thread, fsg, |
3973 | "file-storage-gadget"); | |
3974 | if (IS_ERR(fsg->thread_task)) { | |
3975 | rc = PTR_ERR(fsg->thread_task); | |
1da177e4 | 3976 | goto out; |
22efcf4a | 3977 | } |
1da177e4 LT |
3978 | |
3979 | INFO(fsg, DRIVER_DESC ", version: " DRIVER_VERSION "\n"); | |
3980 | INFO(fsg, "Number of LUNs=%d\n", fsg->nluns); | |
3981 | ||
3982 | pathbuf = kmalloc(PATH_MAX, GFP_KERNEL); | |
3983 | for (i = 0; i < fsg->nluns; ++i) { | |
3984 | curlun = &fsg->luns[i]; | |
3985 | if (backing_file_is_open(curlun)) { | |
3986 | p = NULL; | |
3987 | if (pathbuf) { | |
33cb8994 JS |
3988 | p = d_path(curlun->filp->f_path.dentry, |
3989 | curlun->filp->f_path.mnt, | |
1da177e4 LT |
3990 | pathbuf, PATH_MAX); |
3991 | if (IS_ERR(p)) | |
3992 | p = NULL; | |
3993 | } | |
3994 | LINFO(curlun, "ro=%d, file: %s\n", | |
3995 | curlun->ro, (p ? p : "(error)")); | |
3996 | } | |
3997 | } | |
3998 | kfree(pathbuf); | |
3999 | ||
4000 | DBG(fsg, "transport=%s (x%02x)\n", | |
4001 | mod_data.transport_name, mod_data.transport_type); | |
4002 | DBG(fsg, "protocol=%s (x%02x)\n", | |
4003 | mod_data.protocol_name, mod_data.protocol_type); | |
4004 | DBG(fsg, "VendorID=x%04x, ProductID=x%04x, Release=x%04x\n", | |
4005 | mod_data.vendor, mod_data.product, mod_data.release); | |
4006 | DBG(fsg, "removable=%d, stall=%d, buflen=%u\n", | |
4007 | mod_data.removable, mod_data.can_stall, | |
4008 | mod_data.buflen); | |
22efcf4a | 4009 | DBG(fsg, "I/O thread pid: %d\n", fsg->thread_task->pid); |
a922c687 AS |
4010 | |
4011 | set_bit(REGISTERED, &fsg->atomic_bitflags); | |
4012 | ||
4013 | /* Tell the thread to start working */ | |
4014 | wake_up_process(fsg->thread_task); | |
1da177e4 LT |
4015 | return 0; |
4016 | ||
4017 | autoconf_fail: | |
4018 | ERROR(fsg, "unable to autoconfigure all endpoints\n"); | |
4019 | rc = -ENOTSUPP; | |
4020 | ||
4021 | out: | |
4022 | fsg->state = FSG_STATE_TERMINATED; // The thread is dead | |
4023 | fsg_unbind(gadget); | |
4024 | close_all_backing_files(fsg); | |
4025 | return rc; | |
4026 | } | |
4027 | ||
4028 | ||
4029 | /*-------------------------------------------------------------------------*/ | |
4030 | ||
4031 | static void fsg_suspend(struct usb_gadget *gadget) | |
4032 | { | |
4033 | struct fsg_dev *fsg = get_gadget_data(gadget); | |
4034 | ||
4035 | DBG(fsg, "suspend\n"); | |
4036 | set_bit(SUSPENDED, &fsg->atomic_bitflags); | |
4037 | } | |
4038 | ||
4039 | static void fsg_resume(struct usb_gadget *gadget) | |
4040 | { | |
4041 | struct fsg_dev *fsg = get_gadget_data(gadget); | |
4042 | ||
4043 | DBG(fsg, "resume\n"); | |
4044 | clear_bit(SUSPENDED, &fsg->atomic_bitflags); | |
4045 | } | |
4046 | ||
4047 | ||
4048 | /*-------------------------------------------------------------------------*/ | |
4049 | ||
4050 | static struct usb_gadget_driver fsg_driver = { | |
4051 | #ifdef CONFIG_USB_GADGET_DUALSPEED | |
4052 | .speed = USB_SPEED_HIGH, | |
4053 | #else | |
4054 | .speed = USB_SPEED_FULL, | |
4055 | #endif | |
4056 | .function = (char *) longname, | |
4057 | .bind = fsg_bind, | |
6bea476c | 4058 | .unbind = fsg_unbind, |
1da177e4 LT |
4059 | .disconnect = fsg_disconnect, |
4060 | .setup = fsg_setup, | |
4061 | .suspend = fsg_suspend, | |
4062 | .resume = fsg_resume, | |
4063 | ||
4064 | .driver = { | |
4065 | .name = (char *) shortname, | |
d0d5049f | 4066 | .owner = THIS_MODULE, |
1da177e4 LT |
4067 | // .release = ... |
4068 | // .suspend = ... | |
4069 | // .resume = ... | |
4070 | }, | |
4071 | }; | |
4072 | ||
4073 | ||
4074 | static int __init fsg_alloc(void) | |
4075 | { | |
4076 | struct fsg_dev *fsg; | |
4077 | ||
a922c687 | 4078 | fsg = kzalloc(sizeof *fsg, GFP_KERNEL); |
1da177e4 LT |
4079 | if (!fsg) |
4080 | return -ENOMEM; | |
1da177e4 LT |
4081 | spin_lock_init(&fsg->lock); |
4082 | init_rwsem(&fsg->filesem); | |
87c4252a | 4083 | kref_init(&fsg->ref); |
1da177e4 LT |
4084 | init_completion(&fsg->thread_notifier); |
4085 | ||
4086 | the_fsg = fsg; | |
4087 | return 0; | |
4088 | } | |
4089 | ||
4090 | ||
1da177e4 LT |
4091 | static int __init fsg_init(void) |
4092 | { | |
4093 | int rc; | |
4094 | struct fsg_dev *fsg; | |
4095 | ||
4096 | if ((rc = fsg_alloc()) != 0) | |
4097 | return rc; | |
4098 | fsg = the_fsg; | |
a922c687 | 4099 | if ((rc = usb_gadget_register_driver(&fsg_driver)) != 0) |
87c4252a | 4100 | kref_put(&fsg->ref, fsg_release); |
a922c687 | 4101 | return rc; |
1da177e4 LT |
4102 | } |
4103 | module_init(fsg_init); | |
4104 | ||
4105 | ||
4106 | static void __exit fsg_cleanup(void) | |
4107 | { | |
4108 | struct fsg_dev *fsg = the_fsg; | |
4109 | ||
4110 | /* Unregister the driver iff the thread hasn't already done so */ | |
4111 | if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags)) | |
4112 | usb_gadget_unregister_driver(&fsg_driver); | |
4113 | ||
4114 | /* Wait for the thread to finish up */ | |
4115 | wait_for_completion(&fsg->thread_notifier); | |
4116 | ||
4117 | close_all_backing_files(fsg); | |
87c4252a | 4118 | kref_put(&fsg->ref, fsg_release); |
1da177e4 LT |
4119 | } |
4120 | module_exit(fsg_cleanup); |