Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * omap_udc.c -- for OMAP full speed udc; most chips support OTG. | |
3 | * | |
4 | * Copyright (C) 2004 Texas Instruments, Inc. | |
5 | * Copyright (C) 2004-2005 David Brownell | |
6 | * | |
7 | * This program is free software; you can redistribute it and/or modify | |
8 | * it under the terms of the GNU General Public License as published by | |
9 | * the Free Software Foundation; either version 2 of the License, or | |
10 | * (at your option) any later version. | |
11 | * | |
12 | * This program is distributed in the hope that it will be useful, | |
13 | * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
14 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
15 | * GNU General Public License for more details. | |
16 | * | |
17 | * You should have received a copy of the GNU General Public License | |
18 | * along with this program; if not, write to the Free Software | |
19 | * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA | |
20 | */ | |
21 | ||
22 | #undef DEBUG | |
23 | #undef VERBOSE | |
24 | ||
25 | #include <linux/config.h> | |
26 | #include <linux/module.h> | |
27 | #include <linux/kernel.h> | |
28 | #include <linux/ioport.h> | |
29 | #include <linux/types.h> | |
30 | #include <linux/errno.h> | |
31 | #include <linux/delay.h> | |
32 | #include <linux/sched.h> | |
33 | #include <linux/slab.h> | |
34 | #include <linux/init.h> | |
35 | #include <linux/timer.h> | |
36 | #include <linux/list.h> | |
37 | #include <linux/interrupt.h> | |
38 | #include <linux/proc_fs.h> | |
39 | #include <linux/mm.h> | |
40 | #include <linux/moduleparam.h> | |
41 | #include <linux/device.h> | |
42 | #include <linux/usb_ch9.h> | |
43 | #include <linux/usb_gadget.h> | |
44 | #include <linux/usb_otg.h> | |
45 | #include <linux/dma-mapping.h> | |
46 | ||
47 | #include <asm/byteorder.h> | |
48 | #include <asm/io.h> | |
49 | #include <asm/irq.h> | |
50 | #include <asm/system.h> | |
51 | #include <asm/unaligned.h> | |
52 | #include <asm/mach-types.h> | |
53 | ||
54 | #include <asm/arch/dma.h> | |
55 | #include <asm/arch/mux.h> | |
56 | #include <asm/arch/usb.h> | |
57 | ||
58 | #include "omap_udc.h" | |
59 | ||
60 | #undef USB_TRACE | |
61 | ||
62 | /* bulk DMA seems to be behaving for both IN and OUT */ | |
63 | #define USE_DMA | |
64 | ||
65 | /* ISO too */ | |
66 | #define USE_ISO | |
67 | ||
68 | #define DRIVER_DESC "OMAP UDC driver" | |
69 | #define DRIVER_VERSION "4 October 2004" | |
70 | ||
71 | #define DMA_ADDR_INVALID (~(dma_addr_t)0) | |
72 | ||
73 | ||
74 | /* | |
75 | * The OMAP UDC needs _very_ early endpoint setup: before enabling the | |
76 | * D+ pullup to allow enumeration. That's too early for the gadget | |
77 | * framework to use from usb_endpoint_enable(), which happens after | |
78 | * enumeration as part of activating an interface. (But if we add an | |
79 | * optional new "UDC not yet running" state to the gadget driver model, | |
80 | * even just during driver binding, the endpoint autoconfig logic is the | |
81 | * natural spot to manufacture new endpoints.) | |
82 | * | |
83 | * So instead of using endpoint enable calls to control the hardware setup, | |
84 | * this driver defines a "fifo mode" parameter. It's used during driver | |
85 | * initialization to choose among a set of pre-defined endpoint configs. | |
86 | * See omap_udc_setup() for available modes, or to add others. That code | |
87 | * lives in an init section, so use this driver as a module if you need | |
88 | * to change the fifo mode after the kernel boots. | |
89 | * | |
90 | * Gadget drivers normally ignore endpoints they don't care about, and | |
91 | * won't include them in configuration descriptors. That means only | |
92 | * misbehaving hosts would even notice they exist. | |
93 | */ | |
94 | #ifdef USE_ISO | |
95 | static unsigned fifo_mode = 3; | |
96 | #else | |
97 | static unsigned fifo_mode = 0; | |
98 | #endif | |
99 | ||
100 | /* "modprobe omap_udc fifo_mode=42", or else as a kernel | |
101 | * boot parameter "omap_udc:fifo_mode=42" | |
102 | */ | |
103 | module_param (fifo_mode, uint, 0); | |
104 | MODULE_PARM_DESC (fifo_mode, "endpoint setup (0 == default)"); | |
105 | ||
106 | #ifdef USE_DMA | |
107 | static unsigned use_dma = 1; | |
108 | ||
109 | /* "modprobe omap_udc use_dma=y", or else as a kernel | |
110 | * boot parameter "omap_udc:use_dma=y" | |
111 | */ | |
112 | module_param (use_dma, bool, 0); | |
113 | MODULE_PARM_DESC (use_dma, "enable/disable DMA"); | |
114 | #else /* !USE_DMA */ | |
115 | ||
116 | /* save a bit of code */ | |
117 | #define use_dma 0 | |
118 | #endif /* !USE_DMA */ | |
119 | ||
120 | ||
121 | static const char driver_name [] = "omap_udc"; | |
122 | static const char driver_desc [] = DRIVER_DESC; | |
123 | ||
124 | /*-------------------------------------------------------------------------*/ | |
125 | ||
126 | /* there's a notion of "current endpoint" for modifying endpoint | |
127 | * state, and PIO access to its FIFO. | |
128 | */ | |
129 | ||
130 | static void use_ep(struct omap_ep *ep, u16 select) | |
131 | { | |
132 | u16 num = ep->bEndpointAddress & 0x0f; | |
133 | ||
134 | if (ep->bEndpointAddress & USB_DIR_IN) | |
135 | num |= UDC_EP_DIR; | |
136 | UDC_EP_NUM_REG = num | select; | |
137 | /* when select, MUST deselect later !! */ | |
138 | } | |
139 | ||
140 | static inline void deselect_ep(void) | |
141 | { | |
142 | UDC_EP_NUM_REG &= ~UDC_EP_SEL; | |
143 | /* 6 wait states before TX will happen */ | |
144 | } | |
145 | ||
146 | static void dma_channel_claim(struct omap_ep *ep, unsigned preferred); | |
147 | ||
148 | /*-------------------------------------------------------------------------*/ | |
149 | ||
150 | static int omap_ep_enable(struct usb_ep *_ep, | |
151 | const struct usb_endpoint_descriptor *desc) | |
152 | { | |
153 | struct omap_ep *ep = container_of(_ep, struct omap_ep, ep); | |
154 | struct omap_udc *udc; | |
155 | unsigned long flags; | |
156 | u16 maxp; | |
157 | ||
158 | /* catch various bogus parameters */ | |
159 | if (!_ep || !desc || ep->desc | |
160 | || desc->bDescriptorType != USB_DT_ENDPOINT | |
161 | || ep->bEndpointAddress != desc->bEndpointAddress | |
162 | || ep->maxpacket < le16_to_cpu | |
163 | (desc->wMaxPacketSize)) { | |
164 | DBG("%s, bad ep or descriptor\n", __FUNCTION__); | |
165 | return -EINVAL; | |
166 | } | |
167 | maxp = le16_to_cpu (desc->wMaxPacketSize); | |
168 | if ((desc->bmAttributes == USB_ENDPOINT_XFER_BULK | |
169 | && maxp != ep->maxpacket) | |
170 | || desc->wMaxPacketSize > ep->maxpacket | |
171 | || !desc->wMaxPacketSize) { | |
172 | DBG("%s, bad %s maxpacket\n", __FUNCTION__, _ep->name); | |
173 | return -ERANGE; | |
174 | } | |
175 | ||
176 | #ifdef USE_ISO | |
177 | if ((desc->bmAttributes == USB_ENDPOINT_XFER_ISOC | |
178 | && desc->bInterval != 1)) { | |
179 | /* hardware wants period = 1; USB allows 2^(Interval-1) */ | |
180 | DBG("%s, unsupported ISO period %dms\n", _ep->name, | |
181 | 1 << (desc->bInterval - 1)); | |
182 | return -EDOM; | |
183 | } | |
184 | #else | |
185 | if (desc->bmAttributes == USB_ENDPOINT_XFER_ISOC) { | |
186 | DBG("%s, ISO nyet\n", _ep->name); | |
187 | return -EDOM; | |
188 | } | |
189 | #endif | |
190 | ||
191 | /* xfer types must match, except that interrupt ~= bulk */ | |
192 | if (ep->bmAttributes != desc->bmAttributes | |
193 | && ep->bmAttributes != USB_ENDPOINT_XFER_BULK | |
194 | && desc->bmAttributes != USB_ENDPOINT_XFER_INT) { | |
195 | DBG("%s, %s type mismatch\n", __FUNCTION__, _ep->name); | |
196 | return -EINVAL; | |
197 | } | |
198 | ||
199 | udc = ep->udc; | |
200 | if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) { | |
201 | DBG("%s, bogus device state\n", __FUNCTION__); | |
202 | return -ESHUTDOWN; | |
203 | } | |
204 | ||
205 | spin_lock_irqsave(&udc->lock, flags); | |
206 | ||
207 | ep->desc = desc; | |
208 | ep->irqs = 0; | |
209 | ep->stopped = 0; | |
210 | ep->ep.maxpacket = maxp; | |
211 | ||
212 | /* set endpoint to initial state */ | |
213 | ep->dma_channel = 0; | |
214 | ep->has_dma = 0; | |
215 | ep->lch = -1; | |
216 | use_ep(ep, UDC_EP_SEL); | |
217 | UDC_CTRL_REG = UDC_RESET_EP; | |
218 | ep->ackwait = 0; | |
219 | deselect_ep(); | |
220 | ||
221 | if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) | |
222 | list_add(&ep->iso, &udc->iso); | |
223 | ||
224 | /* maybe assign a DMA channel to this endpoint */ | |
225 | if (use_dma && desc->bmAttributes == USB_ENDPOINT_XFER_BULK) | |
226 | /* FIXME ISO can dma, but prefers first channel */ | |
227 | dma_channel_claim(ep, 0); | |
228 | ||
229 | /* PIO OUT may RX packets */ | |
230 | if (desc->bmAttributes != USB_ENDPOINT_XFER_ISOC | |
231 | && !ep->has_dma | |
232 | && !(ep->bEndpointAddress & USB_DIR_IN)) { | |
233 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
234 | ep->ackwait = 1 + ep->double_buf; | |
235 | } | |
236 | ||
237 | spin_unlock_irqrestore(&udc->lock, flags); | |
238 | VDBG("%s enabled\n", _ep->name); | |
239 | return 0; | |
240 | } | |
241 | ||
242 | static void nuke(struct omap_ep *, int status); | |
243 | ||
244 | static int omap_ep_disable(struct usb_ep *_ep) | |
245 | { | |
246 | struct omap_ep *ep = container_of(_ep, struct omap_ep, ep); | |
247 | unsigned long flags; | |
248 | ||
249 | if (!_ep || !ep->desc) { | |
250 | DBG("%s, %s not enabled\n", __FUNCTION__, | |
251 | _ep ? ep->ep.name : NULL); | |
252 | return -EINVAL; | |
253 | } | |
254 | ||
255 | spin_lock_irqsave(&ep->udc->lock, flags); | |
256 | ep->desc = 0; | |
257 | nuke (ep, -ESHUTDOWN); | |
258 | ep->ep.maxpacket = ep->maxpacket; | |
259 | ep->has_dma = 0; | |
260 | UDC_CTRL_REG = UDC_SET_HALT; | |
261 | list_del_init(&ep->iso); | |
262 | del_timer(&ep->timer); | |
263 | ||
264 | spin_unlock_irqrestore(&ep->udc->lock, flags); | |
265 | ||
266 | VDBG("%s disabled\n", _ep->name); | |
267 | return 0; | |
268 | } | |
269 | ||
270 | /*-------------------------------------------------------------------------*/ | |
271 | ||
272 | static struct usb_request * | |
273 | omap_alloc_request(struct usb_ep *ep, int gfp_flags) | |
274 | { | |
275 | struct omap_req *req; | |
276 | ||
277 | req = kmalloc(sizeof *req, gfp_flags); | |
278 | if (req) { | |
279 | memset (req, 0, sizeof *req); | |
280 | req->req.dma = DMA_ADDR_INVALID; | |
281 | INIT_LIST_HEAD (&req->queue); | |
282 | } | |
283 | return &req->req; | |
284 | } | |
285 | ||
286 | static void | |
287 | omap_free_request(struct usb_ep *ep, struct usb_request *_req) | |
288 | { | |
289 | struct omap_req *req = container_of(_req, struct omap_req, req); | |
290 | ||
291 | if (_req) | |
292 | kfree (req); | |
293 | } | |
294 | ||
295 | /*-------------------------------------------------------------------------*/ | |
296 | ||
297 | static void * | |
298 | omap_alloc_buffer( | |
299 | struct usb_ep *_ep, | |
300 | unsigned bytes, | |
301 | dma_addr_t *dma, | |
302 | int gfp_flags | |
303 | ) | |
304 | { | |
305 | void *retval; | |
306 | struct omap_ep *ep; | |
307 | ||
308 | ep = container_of(_ep, struct omap_ep, ep); | |
309 | if (use_dma && ep->has_dma) { | |
310 | static int warned; | |
311 | if (!warned && bytes < PAGE_SIZE) { | |
312 | dev_warn(ep->udc->gadget.dev.parent, | |
313 | "using dma_alloc_coherent for " | |
314 | "small allocations wastes memory\n"); | |
315 | warned++; | |
316 | } | |
317 | return dma_alloc_coherent(ep->udc->gadget.dev.parent, | |
318 | bytes, dma, gfp_flags); | |
319 | } | |
320 | ||
321 | retval = kmalloc(bytes, gfp_flags); | |
322 | if (retval) | |
323 | *dma = virt_to_phys(retval); | |
324 | return retval; | |
325 | } | |
326 | ||
327 | static void omap_free_buffer( | |
328 | struct usb_ep *_ep, | |
329 | void *buf, | |
330 | dma_addr_t dma, | |
331 | unsigned bytes | |
332 | ) | |
333 | { | |
334 | struct omap_ep *ep; | |
335 | ||
336 | ep = container_of(_ep, struct omap_ep, ep); | |
337 | if (use_dma && _ep && ep->has_dma) | |
338 | dma_free_coherent(ep->udc->gadget.dev.parent, bytes, buf, dma); | |
339 | else | |
340 | kfree (buf); | |
341 | } | |
342 | ||
343 | /*-------------------------------------------------------------------------*/ | |
344 | ||
345 | static void | |
346 | done(struct omap_ep *ep, struct omap_req *req, int status) | |
347 | { | |
348 | unsigned stopped = ep->stopped; | |
349 | ||
350 | list_del_init(&req->queue); | |
351 | ||
352 | if (req->req.status == -EINPROGRESS) | |
353 | req->req.status = status; | |
354 | else | |
355 | status = req->req.status; | |
356 | ||
357 | if (use_dma && ep->has_dma) { | |
358 | if (req->mapped) { | |
359 | dma_unmap_single(ep->udc->gadget.dev.parent, | |
360 | req->req.dma, req->req.length, | |
361 | (ep->bEndpointAddress & USB_DIR_IN) | |
362 | ? DMA_TO_DEVICE | |
363 | : DMA_FROM_DEVICE); | |
364 | req->req.dma = DMA_ADDR_INVALID; | |
365 | req->mapped = 0; | |
366 | } else | |
367 | dma_sync_single_for_cpu(ep->udc->gadget.dev.parent, | |
368 | req->req.dma, req->req.length, | |
369 | (ep->bEndpointAddress & USB_DIR_IN) | |
370 | ? DMA_TO_DEVICE | |
371 | : DMA_FROM_DEVICE); | |
372 | } | |
373 | ||
374 | #ifndef USB_TRACE | |
375 | if (status && status != -ESHUTDOWN) | |
376 | #endif | |
377 | VDBG("complete %s req %p stat %d len %u/%u\n", | |
378 | ep->ep.name, &req->req, status, | |
379 | req->req.actual, req->req.length); | |
380 | ||
381 | /* don't modify queue heads during completion callback */ | |
382 | ep->stopped = 1; | |
383 | spin_unlock(&ep->udc->lock); | |
384 | req->req.complete(&ep->ep, &req->req); | |
385 | spin_lock(&ep->udc->lock); | |
386 | ep->stopped = stopped; | |
387 | } | |
388 | ||
389 | /*-------------------------------------------------------------------------*/ | |
390 | ||
391 | #define FIFO_FULL (UDC_NON_ISO_FIFO_FULL | UDC_ISO_FIFO_FULL) | |
392 | #define FIFO_UNWRITABLE (UDC_EP_HALTED | FIFO_FULL) | |
393 | ||
394 | #define FIFO_EMPTY (UDC_NON_ISO_FIFO_EMPTY | UDC_ISO_FIFO_EMPTY) | |
395 | #define FIFO_UNREADABLE (UDC_EP_HALTED | FIFO_EMPTY) | |
396 | ||
397 | static inline int | |
398 | write_packet(u8 *buf, struct omap_req *req, unsigned max) | |
399 | { | |
400 | unsigned len; | |
401 | u16 *wp; | |
402 | ||
403 | len = min(req->req.length - req->req.actual, max); | |
404 | req->req.actual += len; | |
405 | ||
406 | max = len; | |
407 | if (likely((((int)buf) & 1) == 0)) { | |
408 | wp = (u16 *)buf; | |
409 | while (max >= 2) { | |
410 | UDC_DATA_REG = *wp++; | |
411 | max -= 2; | |
412 | } | |
413 | buf = (u8 *)wp; | |
414 | } | |
415 | while (max--) | |
416 | *(volatile u8 *)&UDC_DATA_REG = *buf++; | |
417 | return len; | |
418 | } | |
419 | ||
420 | // FIXME change r/w fifo calling convention | |
421 | ||
422 | ||
423 | // return: 0 = still running, 1 = completed, negative = errno | |
424 | static int write_fifo(struct omap_ep *ep, struct omap_req *req) | |
425 | { | |
426 | u8 *buf; | |
427 | unsigned count; | |
428 | int is_last; | |
429 | u16 ep_stat; | |
430 | ||
431 | buf = req->req.buf + req->req.actual; | |
432 | prefetch(buf); | |
433 | ||
434 | /* PIO-IN isn't double buffered except for iso */ | |
435 | ep_stat = UDC_STAT_FLG_REG; | |
436 | if (ep_stat & FIFO_UNWRITABLE) | |
437 | return 0; | |
438 | ||
439 | count = ep->ep.maxpacket; | |
440 | count = write_packet(buf, req, count); | |
441 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
442 | ep->ackwait = 1; | |
443 | ||
444 | /* last packet is often short (sometimes a zlp) */ | |
445 | if (count != ep->ep.maxpacket) | |
446 | is_last = 1; | |
447 | else if (req->req.length == req->req.actual | |
448 | && !req->req.zero) | |
449 | is_last = 1; | |
450 | else | |
451 | is_last = 0; | |
452 | ||
453 | /* NOTE: requests complete when all IN data is in a | |
454 | * FIFO (or sometimes later, if a zlp was needed). | |
455 | * Use usb_ep_fifo_status() where needed. | |
456 | */ | |
457 | if (is_last) | |
458 | done(ep, req, 0); | |
459 | return is_last; | |
460 | } | |
461 | ||
462 | static inline int | |
463 | read_packet(u8 *buf, struct omap_req *req, unsigned avail) | |
464 | { | |
465 | unsigned len; | |
466 | u16 *wp; | |
467 | ||
468 | len = min(req->req.length - req->req.actual, avail); | |
469 | req->req.actual += len; | |
470 | avail = len; | |
471 | ||
472 | if (likely((((int)buf) & 1) == 0)) { | |
473 | wp = (u16 *)buf; | |
474 | while (avail >= 2) { | |
475 | *wp++ = UDC_DATA_REG; | |
476 | avail -= 2; | |
477 | } | |
478 | buf = (u8 *)wp; | |
479 | } | |
480 | while (avail--) | |
481 | *buf++ = *(volatile u8 *)&UDC_DATA_REG; | |
482 | return len; | |
483 | } | |
484 | ||
485 | // return: 0 = still running, 1 = queue empty, negative = errno | |
486 | static int read_fifo(struct omap_ep *ep, struct omap_req *req) | |
487 | { | |
488 | u8 *buf; | |
489 | unsigned count, avail; | |
490 | int is_last; | |
491 | ||
492 | buf = req->req.buf + req->req.actual; | |
493 | prefetchw(buf); | |
494 | ||
495 | for (;;) { | |
496 | u16 ep_stat = UDC_STAT_FLG_REG; | |
497 | ||
498 | is_last = 0; | |
499 | if (ep_stat & FIFO_EMPTY) { | |
500 | if (!ep->double_buf) | |
501 | break; | |
502 | ep->fnf = 1; | |
503 | } | |
504 | if (ep_stat & UDC_EP_HALTED) | |
505 | break; | |
506 | ||
507 | if (ep_stat & FIFO_FULL) | |
508 | avail = ep->ep.maxpacket; | |
509 | else { | |
510 | avail = UDC_RXFSTAT_REG; | |
511 | ep->fnf = ep->double_buf; | |
512 | } | |
513 | count = read_packet(buf, req, avail); | |
514 | ||
515 | /* partial packet reads may not be errors */ | |
516 | if (count < ep->ep.maxpacket) { | |
517 | is_last = 1; | |
518 | /* overflowed this request? flush extra data */ | |
519 | if (count != avail) { | |
520 | req->req.status = -EOVERFLOW; | |
521 | avail -= count; | |
522 | while (avail--) | |
523 | (void) *(volatile u8 *)&UDC_DATA_REG; | |
524 | } | |
525 | } else if (req->req.length == req->req.actual) | |
526 | is_last = 1; | |
527 | else | |
528 | is_last = 0; | |
529 | ||
530 | if (!ep->bEndpointAddress) | |
531 | break; | |
532 | if (is_last) | |
533 | done(ep, req, 0); | |
534 | break; | |
535 | } | |
536 | return is_last; | |
537 | } | |
538 | ||
539 | /*-------------------------------------------------------------------------*/ | |
540 | ||
541 | static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start) | |
542 | { | |
543 | dma_addr_t end; | |
544 | ||
545 | /* IN-DMA needs this on fault/cancel paths, so 15xx misreports | |
546 | * the last transfer's bytecount by more than a FIFO's worth. | |
547 | */ | |
548 | if (cpu_is_omap15xx()) | |
549 | return 0; | |
550 | ||
551 | end = omap_readw(OMAP_DMA_CSAC(ep->lch)); | |
552 | if (end == ep->dma_counter) | |
553 | return 0; | |
554 | ||
555 | end |= start & (0xffff << 16); | |
556 | if (end < start) | |
557 | end += 0x10000; | |
558 | return end - start; | |
559 | } | |
560 | ||
561 | #define DMA_DEST_LAST(x) (cpu_is_omap15xx() \ | |
562 | ? OMAP_DMA_CSAC(x) /* really: CPC */ \ | |
563 | : OMAP_DMA_CDAC(x)) | |
564 | ||
565 | static u16 dma_dest_len(struct omap_ep *ep, dma_addr_t start) | |
566 | { | |
567 | dma_addr_t end; | |
568 | ||
569 | end = omap_readw(DMA_DEST_LAST(ep->lch)); | |
570 | if (end == ep->dma_counter) | |
571 | return 0; | |
572 | ||
573 | end |= start & (0xffff << 16); | |
574 | if (cpu_is_omap15xx()) | |
575 | end++; | |
576 | if (end < start) | |
577 | end += 0x10000; | |
578 | return end - start; | |
579 | } | |
580 | ||
581 | ||
582 | /* Each USB transfer request using DMA maps to one or more DMA transfers. | |
583 | * When DMA completion isn't request completion, the UDC continues with | |
584 | * the next DMA transfer for that USB transfer. | |
585 | */ | |
586 | ||
587 | static void next_in_dma(struct omap_ep *ep, struct omap_req *req) | |
588 | { | |
589 | u16 txdma_ctrl; | |
590 | unsigned length = req->req.length - req->req.actual; | |
591 | const int sync_mode = cpu_is_omap15xx() | |
592 | ? OMAP_DMA_SYNC_FRAME | |
593 | : OMAP_DMA_SYNC_ELEMENT; | |
594 | ||
595 | /* measure length in either bytes or packets */ | |
596 | if ((cpu_is_omap16xx() && length <= (UDC_TXN_TSC + 1)) | |
597 | || (cpu_is_omap15xx() && length < ep->maxpacket)) { | |
598 | txdma_ctrl = UDC_TXN_EOT | length; | |
599 | omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S8, | |
600 | length, 1, sync_mode); | |
601 | } else { | |
602 | length = min(length / ep->maxpacket, | |
603 | (unsigned) UDC_TXN_TSC + 1); | |
604 | txdma_ctrl = length; | |
605 | omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S8, | |
606 | ep->ep.maxpacket, length, sync_mode); | |
607 | length *= ep->maxpacket; | |
608 | } | |
609 | omap_set_dma_src_params(ep->lch, OMAP_DMA_PORT_EMIFF, | |
610 | OMAP_DMA_AMODE_POST_INC, req->req.dma + req->req.actual); | |
611 | ||
612 | omap_start_dma(ep->lch); | |
613 | ep->dma_counter = omap_readw(OMAP_DMA_CSAC(ep->lch)); | |
614 | UDC_DMA_IRQ_EN_REG |= UDC_TX_DONE_IE(ep->dma_channel); | |
615 | UDC_TXDMA_REG(ep->dma_channel) = UDC_TXN_START | txdma_ctrl; | |
616 | req->dma_bytes = length; | |
617 | } | |
618 | ||
619 | static void finish_in_dma(struct omap_ep *ep, struct omap_req *req, int status) | |
620 | { | |
621 | if (status == 0) { | |
622 | req->req.actual += req->dma_bytes; | |
623 | ||
624 | /* return if this request needs to send data or zlp */ | |
625 | if (req->req.actual < req->req.length) | |
626 | return; | |
627 | if (req->req.zero | |
628 | && req->dma_bytes != 0 | |
629 | && (req->req.actual % ep->maxpacket) == 0) | |
630 | return; | |
631 | } else | |
632 | req->req.actual += dma_src_len(ep, req->req.dma | |
633 | + req->req.actual); | |
634 | ||
635 | /* tx completion */ | |
636 | omap_stop_dma(ep->lch); | |
637 | UDC_DMA_IRQ_EN_REG &= ~UDC_TX_DONE_IE(ep->dma_channel); | |
638 | done(ep, req, status); | |
639 | } | |
640 | ||
641 | static void next_out_dma(struct omap_ep *ep, struct omap_req *req) | |
642 | { | |
643 | unsigned packets; | |
644 | ||
645 | /* NOTE: we filtered out "short reads" before, so we know | |
646 | * the buffer has only whole numbers of packets. | |
647 | */ | |
648 | ||
649 | /* set up this DMA transfer, enable the fifo, start */ | |
650 | packets = (req->req.length - req->req.actual) / ep->ep.maxpacket; | |
651 | packets = min(packets, (unsigned)UDC_RXN_TC + 1); | |
652 | req->dma_bytes = packets * ep->ep.maxpacket; | |
653 | omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S8, | |
654 | ep->ep.maxpacket, packets, | |
655 | OMAP_DMA_SYNC_ELEMENT); | |
656 | omap_set_dma_dest_params(ep->lch, OMAP_DMA_PORT_EMIFF, | |
657 | OMAP_DMA_AMODE_POST_INC, req->req.dma + req->req.actual); | |
658 | ep->dma_counter = omap_readw(DMA_DEST_LAST(ep->lch)); | |
659 | ||
660 | UDC_RXDMA_REG(ep->dma_channel) = UDC_RXN_STOP | (packets - 1); | |
661 | UDC_DMA_IRQ_EN_REG |= UDC_RX_EOT_IE(ep->dma_channel); | |
662 | UDC_EP_NUM_REG = (ep->bEndpointAddress & 0xf); | |
663 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
664 | ||
665 | omap_start_dma(ep->lch); | |
666 | } | |
667 | ||
668 | static void | |
669 | finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status) | |
670 | { | |
671 | u16 count; | |
672 | ||
673 | if (status == 0) | |
674 | ep->dma_counter = (u16) (req->req.dma + req->req.actual); | |
675 | count = dma_dest_len(ep, req->req.dma + req->req.actual); | |
676 | count += req->req.actual; | |
677 | if (count <= req->req.length) | |
678 | req->req.actual = count; | |
679 | ||
680 | if (count != req->dma_bytes || status) | |
681 | omap_stop_dma(ep->lch); | |
682 | ||
683 | /* if this wasn't short, request may need another transfer */ | |
684 | else if (req->req.actual < req->req.length) | |
685 | return; | |
686 | ||
687 | /* rx completion */ | |
688 | UDC_DMA_IRQ_EN_REG &= ~UDC_RX_EOT_IE(ep->dma_channel); | |
689 | done(ep, req, status); | |
690 | } | |
691 | ||
692 | static void dma_irq(struct omap_udc *udc, u16 irq_src) | |
693 | { | |
694 | u16 dman_stat = UDC_DMAN_STAT_REG; | |
695 | struct omap_ep *ep; | |
696 | struct omap_req *req; | |
697 | ||
698 | /* IN dma: tx to host */ | |
699 | if (irq_src & UDC_TXN_DONE) { | |
700 | ep = &udc->ep[16 + UDC_DMA_TX_SRC(dman_stat)]; | |
701 | ep->irqs++; | |
702 | /* can see TXN_DONE after dma abort */ | |
703 | if (!list_empty(&ep->queue)) { | |
704 | req = container_of(ep->queue.next, | |
705 | struct omap_req, queue); | |
706 | finish_in_dma(ep, req, 0); | |
707 | } | |
708 | UDC_IRQ_SRC_REG = UDC_TXN_DONE; | |
709 | ||
710 | if (!list_empty (&ep->queue)) { | |
711 | req = container_of(ep->queue.next, | |
712 | struct omap_req, queue); | |
713 | next_in_dma(ep, req); | |
714 | } | |
715 | } | |
716 | ||
717 | /* OUT dma: rx from host */ | |
718 | if (irq_src & UDC_RXN_EOT) { | |
719 | ep = &udc->ep[UDC_DMA_RX_SRC(dman_stat)]; | |
720 | ep->irqs++; | |
721 | /* can see RXN_EOT after dma abort */ | |
722 | if (!list_empty(&ep->queue)) { | |
723 | req = container_of(ep->queue.next, | |
724 | struct omap_req, queue); | |
725 | finish_out_dma(ep, req, 0); | |
726 | } | |
727 | UDC_IRQ_SRC_REG = UDC_RXN_EOT; | |
728 | ||
729 | if (!list_empty (&ep->queue)) { | |
730 | req = container_of(ep->queue.next, | |
731 | struct omap_req, queue); | |
732 | next_out_dma(ep, req); | |
733 | } | |
734 | } | |
735 | ||
736 | if (irq_src & UDC_RXN_CNT) { | |
737 | ep = &udc->ep[UDC_DMA_RX_SRC(dman_stat)]; | |
738 | ep->irqs++; | |
739 | /* omap15xx does this unasked... */ | |
740 | VDBG("%s, RX_CNT irq?\n", ep->ep.name); | |
741 | UDC_IRQ_SRC_REG = UDC_RXN_CNT; | |
742 | } | |
743 | } | |
744 | ||
745 | static void dma_error(int lch, u16 ch_status, void *data) | |
746 | { | |
747 | struct omap_ep *ep = data; | |
748 | ||
749 | /* if ch_status & OMAP_DMA_DROP_IRQ ... */ | |
750 | /* if ch_status & OMAP_DMA_TOUT_IRQ ... */ | |
751 | ERR("%s dma error, lch %d status %02x\n", ep->ep.name, lch, ch_status); | |
752 | ||
753 | /* complete current transfer ... */ | |
754 | } | |
755 | ||
756 | static void dma_channel_claim(struct omap_ep *ep, unsigned channel) | |
757 | { | |
758 | u16 reg; | |
759 | int status, restart, is_in; | |
760 | ||
761 | is_in = ep->bEndpointAddress & USB_DIR_IN; | |
762 | if (is_in) | |
763 | reg = UDC_TXDMA_CFG_REG; | |
764 | else | |
765 | reg = UDC_RXDMA_CFG_REG; | |
766 | reg |= 1 << 12; /* "pulse" activated */ | |
767 | ||
768 | ep->dma_channel = 0; | |
769 | ep->lch = -1; | |
770 | if (channel == 0 || channel > 3) { | |
771 | if ((reg & 0x0f00) == 0) | |
772 | channel = 3; | |
773 | else if ((reg & 0x00f0) == 0) | |
774 | channel = 2; | |
775 | else if ((reg & 0x000f) == 0) /* preferred for ISO */ | |
776 | channel = 1; | |
777 | else { | |
778 | status = -EMLINK; | |
779 | goto just_restart; | |
780 | } | |
781 | } | |
782 | reg |= (0x0f & ep->bEndpointAddress) << (4 * (channel - 1)); | |
783 | ep->dma_channel = channel; | |
784 | ||
785 | if (is_in) { | |
786 | status = omap_request_dma(OMAP_DMA_USB_W2FC_TX0 - 1 + channel, | |
787 | ep->ep.name, dma_error, ep, &ep->lch); | |
788 | if (status == 0) { | |
789 | UDC_TXDMA_CFG_REG = reg; | |
790 | omap_set_dma_dest_params(ep->lch, | |
791 | OMAP_DMA_PORT_TIPB, | |
792 | OMAP_DMA_AMODE_CONSTANT, | |
793 | (unsigned long) io_v2p((u32)&UDC_DATA_DMA_REG)); | |
794 | } | |
795 | } else { | |
796 | status = omap_request_dma(OMAP_DMA_USB_W2FC_RX0 - 1 + channel, | |
797 | ep->ep.name, dma_error, ep, &ep->lch); | |
798 | if (status == 0) { | |
799 | UDC_RXDMA_CFG_REG = reg; | |
800 | omap_set_dma_src_params(ep->lch, | |
801 | OMAP_DMA_PORT_TIPB, | |
802 | OMAP_DMA_AMODE_CONSTANT, | |
803 | (unsigned long) io_v2p((u32)&UDC_DATA_DMA_REG)); | |
804 | } | |
805 | } | |
806 | if (status) | |
807 | ep->dma_channel = 0; | |
808 | else { | |
809 | ep->has_dma = 1; | |
810 | omap_disable_dma_irq(ep->lch, OMAP_DMA_BLOCK_IRQ); | |
811 | ||
812 | /* channel type P: hw synch (fifo) */ | |
813 | if (!cpu_is_omap15xx()) | |
814 | omap_writew(2, OMAP_DMA_LCH_CTRL(ep->lch)); | |
815 | } | |
816 | ||
817 | just_restart: | |
818 | /* restart any queue, even if the claim failed */ | |
819 | restart = !ep->stopped && !list_empty(&ep->queue); | |
820 | ||
821 | if (status) | |
822 | DBG("%s no dma channel: %d%s\n", ep->ep.name, status, | |
823 | restart ? " (restart)" : ""); | |
824 | else | |
825 | DBG("%s claimed %cxdma%d lch %d%s\n", ep->ep.name, | |
826 | is_in ? 't' : 'r', | |
827 | ep->dma_channel - 1, ep->lch, | |
828 | restart ? " (restart)" : ""); | |
829 | ||
830 | if (restart) { | |
831 | struct omap_req *req; | |
832 | req = container_of(ep->queue.next, struct omap_req, queue); | |
833 | if (ep->has_dma) | |
834 | (is_in ? next_in_dma : next_out_dma)(ep, req); | |
835 | else { | |
836 | use_ep(ep, UDC_EP_SEL); | |
837 | (is_in ? write_fifo : read_fifo)(ep, req); | |
838 | deselect_ep(); | |
839 | if (!is_in) { | |
840 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
841 | ep->ackwait = 1 + ep->double_buf; | |
842 | } | |
843 | /* IN: 6 wait states before it'll tx */ | |
844 | } | |
845 | } | |
846 | } | |
847 | ||
848 | static void dma_channel_release(struct omap_ep *ep) | |
849 | { | |
850 | int shift = 4 * (ep->dma_channel - 1); | |
851 | u16 mask = 0x0f << shift; | |
852 | struct omap_req *req; | |
853 | int active; | |
854 | ||
855 | /* abort any active usb transfer request */ | |
856 | if (!list_empty(&ep->queue)) | |
857 | req = container_of(ep->queue.next, struct omap_req, queue); | |
858 | else | |
859 | req = 0; | |
860 | ||
861 | active = ((1 << 7) & omap_readl(OMAP_DMA_CCR(ep->lch))) != 0; | |
862 | ||
863 | DBG("%s release %s %cxdma%d %p\n", ep->ep.name, | |
864 | active ? "active" : "idle", | |
865 | (ep->bEndpointAddress & USB_DIR_IN) ? 't' : 'r', | |
866 | ep->dma_channel - 1, req); | |
867 | ||
868 | /* wait till current packet DMA finishes, and fifo empties */ | |
869 | if (ep->bEndpointAddress & USB_DIR_IN) { | |
870 | UDC_TXDMA_CFG_REG &= ~mask; | |
871 | ||
872 | if (req) { | |
873 | finish_in_dma(ep, req, -ECONNRESET); | |
874 | ||
875 | /* clear FIFO; hosts probably won't empty it */ | |
876 | use_ep(ep, UDC_EP_SEL); | |
877 | UDC_CTRL_REG = UDC_CLR_EP; | |
878 | deselect_ep(); | |
879 | } | |
880 | while (UDC_TXDMA_CFG_REG & mask) | |
881 | udelay(10); | |
882 | } else { | |
883 | UDC_RXDMA_CFG_REG &= ~mask; | |
884 | ||
885 | /* dma empties the fifo */ | |
886 | while (UDC_RXDMA_CFG_REG & mask) | |
887 | udelay(10); | |
888 | if (req) | |
889 | finish_out_dma(ep, req, -ECONNRESET); | |
890 | } | |
891 | omap_free_dma(ep->lch); | |
892 | ep->dma_channel = 0; | |
893 | ep->lch = -1; | |
894 | /* has_dma still set, till endpoint is fully quiesced */ | |
895 | } | |
896 | ||
897 | ||
898 | /*-------------------------------------------------------------------------*/ | |
899 | ||
900 | static int | |
901 | omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, int gfp_flags) | |
902 | { | |
903 | struct omap_ep *ep = container_of(_ep, struct omap_ep, ep); | |
904 | struct omap_req *req = container_of(_req, struct omap_req, req); | |
905 | struct omap_udc *udc; | |
906 | unsigned long flags; | |
907 | int is_iso = 0; | |
908 | ||
909 | /* catch various bogus parameters */ | |
910 | if (!_req || !req->req.complete || !req->req.buf | |
911 | || !list_empty(&req->queue)) { | |
912 | DBG("%s, bad params\n", __FUNCTION__); | |
913 | return -EINVAL; | |
914 | } | |
915 | if (!_ep || (!ep->desc && ep->bEndpointAddress)) { | |
916 | DBG("%s, bad ep\n", __FUNCTION__); | |
917 | return -EINVAL; | |
918 | } | |
919 | if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) { | |
920 | if (req->req.length > ep->ep.maxpacket) | |
921 | return -EMSGSIZE; | |
922 | is_iso = 1; | |
923 | } | |
924 | ||
925 | /* this isn't bogus, but OMAP DMA isn't the only hardware to | |
926 | * have a hard time with partial packet reads... reject it. | |
927 | */ | |
928 | if (use_dma | |
929 | && ep->has_dma | |
930 | && ep->bEndpointAddress != 0 | |
931 | && (ep->bEndpointAddress & USB_DIR_IN) == 0 | |
932 | && (req->req.length % ep->ep.maxpacket) != 0) { | |
933 | DBG("%s, no partial packet OUT reads\n", __FUNCTION__); | |
934 | return -EMSGSIZE; | |
935 | } | |
936 | ||
937 | udc = ep->udc; | |
938 | if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) | |
939 | return -ESHUTDOWN; | |
940 | ||
941 | if (use_dma && ep->has_dma) { | |
942 | if (req->req.dma == DMA_ADDR_INVALID) { | |
943 | req->req.dma = dma_map_single( | |
944 | ep->udc->gadget.dev.parent, | |
945 | req->req.buf, | |
946 | req->req.length, | |
947 | (ep->bEndpointAddress & USB_DIR_IN) | |
948 | ? DMA_TO_DEVICE | |
949 | : DMA_FROM_DEVICE); | |
950 | req->mapped = 1; | |
951 | } else { | |
952 | dma_sync_single_for_device( | |
953 | ep->udc->gadget.dev.parent, | |
954 | req->req.dma, req->req.length, | |
955 | (ep->bEndpointAddress & USB_DIR_IN) | |
956 | ? DMA_TO_DEVICE | |
957 | : DMA_FROM_DEVICE); | |
958 | req->mapped = 0; | |
959 | } | |
960 | } | |
961 | ||
962 | VDBG("%s queue req %p, len %d buf %p\n", | |
963 | ep->ep.name, _req, _req->length, _req->buf); | |
964 | ||
965 | spin_lock_irqsave(&udc->lock, flags); | |
966 | ||
967 | req->req.status = -EINPROGRESS; | |
968 | req->req.actual = 0; | |
969 | ||
970 | /* maybe kickstart non-iso i/o queues */ | |
971 | if (is_iso) | |
972 | UDC_IRQ_EN_REG |= UDC_SOF_IE; | |
973 | else if (list_empty(&ep->queue) && !ep->stopped && !ep->ackwait) { | |
974 | int is_in; | |
975 | ||
976 | if (ep->bEndpointAddress == 0) { | |
977 | if (!udc->ep0_pending || !list_empty (&ep->queue)) { | |
978 | spin_unlock_irqrestore(&udc->lock, flags); | |
979 | return -EL2HLT; | |
980 | } | |
981 | ||
982 | /* empty DATA stage? */ | |
983 | is_in = udc->ep0_in; | |
984 | if (!req->req.length) { | |
985 | ||
986 | /* chip became CONFIGURED or ADDRESSED | |
987 | * earlier; drivers may already have queued | |
988 | * requests to non-control endpoints | |
989 | */ | |
990 | if (udc->ep0_set_config) { | |
991 | u16 irq_en = UDC_IRQ_EN_REG; | |
992 | ||
993 | irq_en |= UDC_DS_CHG_IE | UDC_EP0_IE; | |
994 | if (!udc->ep0_reset_config) | |
995 | irq_en |= UDC_EPN_RX_IE | |
996 | | UDC_EPN_TX_IE; | |
997 | UDC_IRQ_EN_REG = irq_en; | |
998 | } | |
999 | ||
1000 | /* STATUS is reverse direction */ | |
1001 | UDC_EP_NUM_REG = is_in | |
1002 | ? UDC_EP_SEL | |
1003 | : (UDC_EP_SEL|UDC_EP_DIR); | |
1004 | UDC_CTRL_REG = UDC_CLR_EP; | |
1005 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1006 | UDC_EP_NUM_REG = udc->ep0_in ? 0 : UDC_EP_DIR; | |
1007 | ||
1008 | /* cleanup */ | |
1009 | udc->ep0_pending = 0; | |
1010 | done(ep, req, 0); | |
1011 | req = 0; | |
1012 | ||
1013 | /* non-empty DATA stage */ | |
1014 | } else if (is_in) { | |
1015 | UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; | |
1016 | } else { | |
1017 | if (udc->ep0_setup) | |
1018 | goto irq_wait; | |
1019 | UDC_EP_NUM_REG = UDC_EP_SEL; | |
1020 | } | |
1021 | } else { | |
1022 | is_in = ep->bEndpointAddress & USB_DIR_IN; | |
1023 | if (!ep->has_dma) | |
1024 | use_ep(ep, UDC_EP_SEL); | |
1025 | /* if ISO: SOF IRQs must be enabled/disabled! */ | |
1026 | } | |
1027 | ||
1028 | if (ep->has_dma) | |
1029 | (is_in ? next_in_dma : next_out_dma)(ep, req); | |
1030 | else if (req) { | |
1031 | if ((is_in ? write_fifo : read_fifo)(ep, req) == 1) | |
1032 | req = 0; | |
1033 | deselect_ep(); | |
1034 | if (!is_in) { | |
1035 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1036 | ep->ackwait = 1 + ep->double_buf; | |
1037 | } | |
1038 | /* IN: 6 wait states before it'll tx */ | |
1039 | } | |
1040 | } | |
1041 | ||
1042 | irq_wait: | |
1043 | /* irq handler advances the queue */ | |
1044 | if (req != 0) | |
1045 | list_add_tail(&req->queue, &ep->queue); | |
1046 | spin_unlock_irqrestore(&udc->lock, flags); | |
1047 | ||
1048 | return 0; | |
1049 | } | |
1050 | ||
1051 | static int omap_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req) | |
1052 | { | |
1053 | struct omap_ep *ep = container_of(_ep, struct omap_ep, ep); | |
1054 | struct omap_req *req; | |
1055 | unsigned long flags; | |
1056 | ||
1057 | if (!_ep || !_req) | |
1058 | return -EINVAL; | |
1059 | ||
1060 | spin_lock_irqsave(&ep->udc->lock, flags); | |
1061 | ||
1062 | /* make sure it's actually queued on this endpoint */ | |
1063 | list_for_each_entry (req, &ep->queue, queue) { | |
1064 | if (&req->req == _req) | |
1065 | break; | |
1066 | } | |
1067 | if (&req->req != _req) { | |
1068 | spin_unlock_irqrestore(&ep->udc->lock, flags); | |
1069 | return -EINVAL; | |
1070 | } | |
1071 | ||
1072 | if (use_dma && ep->dma_channel && ep->queue.next == &req->queue) { | |
1073 | int channel = ep->dma_channel; | |
1074 | ||
1075 | /* releasing the channel cancels the request, | |
1076 | * reclaiming the channel restarts the queue | |
1077 | */ | |
1078 | dma_channel_release(ep); | |
1079 | dma_channel_claim(ep, channel); | |
1080 | } else | |
1081 | done(ep, req, -ECONNRESET); | |
1082 | spin_unlock_irqrestore(&ep->udc->lock, flags); | |
1083 | return 0; | |
1084 | } | |
1085 | ||
1086 | /*-------------------------------------------------------------------------*/ | |
1087 | ||
1088 | static int omap_ep_set_halt(struct usb_ep *_ep, int value) | |
1089 | { | |
1090 | struct omap_ep *ep = container_of(_ep, struct omap_ep, ep); | |
1091 | unsigned long flags; | |
1092 | int status = -EOPNOTSUPP; | |
1093 | ||
1094 | spin_lock_irqsave(&ep->udc->lock, flags); | |
1095 | ||
1096 | /* just use protocol stalls for ep0; real halts are annoying */ | |
1097 | if (ep->bEndpointAddress == 0) { | |
1098 | if (!ep->udc->ep0_pending) | |
1099 | status = -EINVAL; | |
1100 | else if (value) { | |
1101 | if (ep->udc->ep0_set_config) { | |
1102 | WARN("error changing config?\n"); | |
1103 | UDC_SYSCON2_REG = UDC_CLR_CFG; | |
1104 | } | |
1105 | UDC_SYSCON2_REG = UDC_STALL_CMD; | |
1106 | ep->udc->ep0_pending = 0; | |
1107 | status = 0; | |
1108 | } else /* NOP */ | |
1109 | status = 0; | |
1110 | ||
1111 | /* otherwise, all active non-ISO endpoints can halt */ | |
1112 | } else if (ep->bmAttributes != USB_ENDPOINT_XFER_ISOC && ep->desc) { | |
1113 | ||
1114 | /* IN endpoints must already be idle */ | |
1115 | if ((ep->bEndpointAddress & USB_DIR_IN) | |
1116 | && !list_empty(&ep->queue)) { | |
1117 | status = -EAGAIN; | |
1118 | goto done; | |
1119 | } | |
1120 | ||
1121 | if (value) { | |
1122 | int channel; | |
1123 | ||
1124 | if (use_dma && ep->dma_channel | |
1125 | && !list_empty(&ep->queue)) { | |
1126 | channel = ep->dma_channel; | |
1127 | dma_channel_release(ep); | |
1128 | } else | |
1129 | channel = 0; | |
1130 | ||
1131 | use_ep(ep, UDC_EP_SEL); | |
1132 | if (UDC_STAT_FLG_REG & UDC_NON_ISO_FIFO_EMPTY) { | |
1133 | UDC_CTRL_REG = UDC_SET_HALT; | |
1134 | status = 0; | |
1135 | } else | |
1136 | status = -EAGAIN; | |
1137 | deselect_ep(); | |
1138 | ||
1139 | if (channel) | |
1140 | dma_channel_claim(ep, channel); | |
1141 | } else { | |
1142 | use_ep(ep, 0); | |
1143 | UDC_CTRL_REG = UDC_RESET_EP; | |
1144 | ep->ackwait = 0; | |
1145 | if (!(ep->bEndpointAddress & USB_DIR_IN)) { | |
1146 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1147 | ep->ackwait = 1 + ep->double_buf; | |
1148 | } | |
1149 | } | |
1150 | } | |
1151 | done: | |
1152 | VDBG("%s %s halt stat %d\n", ep->ep.name, | |
1153 | value ? "set" : "clear", status); | |
1154 | ||
1155 | spin_unlock_irqrestore(&ep->udc->lock, flags); | |
1156 | return status; | |
1157 | } | |
1158 | ||
1159 | static struct usb_ep_ops omap_ep_ops = { | |
1160 | .enable = omap_ep_enable, | |
1161 | .disable = omap_ep_disable, | |
1162 | ||
1163 | .alloc_request = omap_alloc_request, | |
1164 | .free_request = omap_free_request, | |
1165 | ||
1166 | .alloc_buffer = omap_alloc_buffer, | |
1167 | .free_buffer = omap_free_buffer, | |
1168 | ||
1169 | .queue = omap_ep_queue, | |
1170 | .dequeue = omap_ep_dequeue, | |
1171 | ||
1172 | .set_halt = omap_ep_set_halt, | |
1173 | // fifo_status ... report bytes in fifo | |
1174 | // fifo_flush ... flush fifo | |
1175 | }; | |
1176 | ||
1177 | /*-------------------------------------------------------------------------*/ | |
1178 | ||
1179 | static int omap_get_frame(struct usb_gadget *gadget) | |
1180 | { | |
1181 | u16 sof = UDC_SOF_REG; | |
1182 | return (sof & UDC_TS_OK) ? (sof & UDC_TS) : -EL2NSYNC; | |
1183 | } | |
1184 | ||
1185 | static int omap_wakeup(struct usb_gadget *gadget) | |
1186 | { | |
1187 | struct omap_udc *udc; | |
1188 | unsigned long flags; | |
1189 | int retval = -EHOSTUNREACH; | |
1190 | ||
1191 | udc = container_of(gadget, struct omap_udc, gadget); | |
1192 | ||
1193 | spin_lock_irqsave(&udc->lock, flags); | |
1194 | if (udc->devstat & UDC_SUS) { | |
1195 | /* NOTE: OTG spec erratum says that OTG devices may | |
1196 | * issue wakeups without host enable. | |
1197 | */ | |
1198 | if (udc->devstat & (UDC_B_HNP_ENABLE|UDC_R_WK_OK)) { | |
1199 | DBG("remote wakeup...\n"); | |
1200 | UDC_SYSCON2_REG = UDC_RMT_WKP; | |
1201 | retval = 0; | |
1202 | } | |
1203 | ||
1204 | /* NOTE: non-OTG systems may use SRP TOO... */ | |
1205 | } else if (!(udc->devstat & UDC_ATT)) { | |
1206 | if (udc->transceiver) | |
1207 | retval = otg_start_srp(udc->transceiver); | |
1208 | } | |
1209 | spin_unlock_irqrestore(&udc->lock, flags); | |
1210 | ||
1211 | return retval; | |
1212 | } | |
1213 | ||
1214 | static int | |
1215 | omap_set_selfpowered(struct usb_gadget *gadget, int is_selfpowered) | |
1216 | { | |
1217 | struct omap_udc *udc; | |
1218 | unsigned long flags; | |
1219 | u16 syscon1; | |
1220 | ||
1221 | udc = container_of(gadget, struct omap_udc, gadget); | |
1222 | spin_lock_irqsave(&udc->lock, flags); | |
1223 | syscon1 = UDC_SYSCON1_REG; | |
1224 | if (is_selfpowered) | |
1225 | syscon1 |= UDC_SELF_PWR; | |
1226 | else | |
1227 | syscon1 &= ~UDC_SELF_PWR; | |
1228 | UDC_SYSCON1_REG = syscon1; | |
1229 | spin_unlock_irqrestore(&udc->lock, flags); | |
1230 | ||
1231 | return 0; | |
1232 | } | |
1233 | ||
1234 | static int can_pullup(struct omap_udc *udc) | |
1235 | { | |
1236 | return udc->driver && udc->softconnect && udc->vbus_active; | |
1237 | } | |
1238 | ||
1239 | static void pullup_enable(struct omap_udc *udc) | |
1240 | { | |
1241 | UDC_SYSCON1_REG |= UDC_PULLUP_EN; | |
1242 | #ifndef CONFIG_USB_OTG | |
1243 | if (!cpu_is_omap15xx()) | |
1244 | OTG_CTRL_REG |= OTG_BSESSVLD; | |
1245 | #endif | |
1246 | UDC_IRQ_EN_REG = UDC_DS_CHG_IE; | |
1247 | } | |
1248 | ||
1249 | static void pullup_disable(struct omap_udc *udc) | |
1250 | { | |
1251 | #ifndef CONFIG_USB_OTG | |
1252 | if (!cpu_is_omap15xx()) | |
1253 | OTG_CTRL_REG &= ~OTG_BSESSVLD; | |
1254 | #endif | |
1255 | UDC_IRQ_EN_REG = UDC_DS_CHG_IE; | |
1256 | UDC_SYSCON1_REG &= ~UDC_PULLUP_EN; | |
1257 | } | |
1258 | ||
1259 | /* | |
1260 | * Called by whatever detects VBUS sessions: external transceiver | |
1261 | * driver, or maybe GPIO0 VBUS IRQ. May request 48 MHz clock. | |
1262 | */ | |
1263 | static int omap_vbus_session(struct usb_gadget *gadget, int is_active) | |
1264 | { | |
1265 | struct omap_udc *udc; | |
1266 | unsigned long flags; | |
1267 | ||
1268 | udc = container_of(gadget, struct omap_udc, gadget); | |
1269 | spin_lock_irqsave(&udc->lock, flags); | |
1270 | VDBG("VBUS %s\n", is_active ? "on" : "off"); | |
1271 | udc->vbus_active = (is_active != 0); | |
1272 | if (cpu_is_omap15xx()) { | |
1273 | /* "software" detect, ignored if !VBUS_MODE_1510 */ | |
1274 | if (is_active) | |
1275 | FUNC_MUX_CTRL_0_REG |= VBUS_CTRL_1510; | |
1276 | else | |
1277 | FUNC_MUX_CTRL_0_REG &= ~VBUS_CTRL_1510; | |
1278 | } | |
1279 | if (can_pullup(udc)) | |
1280 | pullup_enable(udc); | |
1281 | else | |
1282 | pullup_disable(udc); | |
1283 | spin_unlock_irqrestore(&udc->lock, flags); | |
1284 | return 0; | |
1285 | } | |
1286 | ||
1287 | static int omap_vbus_draw(struct usb_gadget *gadget, unsigned mA) | |
1288 | { | |
1289 | struct omap_udc *udc; | |
1290 | ||
1291 | udc = container_of(gadget, struct omap_udc, gadget); | |
1292 | if (udc->transceiver) | |
1293 | return otg_set_power(udc->transceiver, mA); | |
1294 | return -EOPNOTSUPP; | |
1295 | } | |
1296 | ||
1297 | static int omap_pullup(struct usb_gadget *gadget, int is_on) | |
1298 | { | |
1299 | struct omap_udc *udc; | |
1300 | unsigned long flags; | |
1301 | ||
1302 | udc = container_of(gadget, struct omap_udc, gadget); | |
1303 | spin_lock_irqsave(&udc->lock, flags); | |
1304 | udc->softconnect = (is_on != 0); | |
1305 | if (can_pullup(udc)) | |
1306 | pullup_enable(udc); | |
1307 | else | |
1308 | pullup_disable(udc); | |
1309 | spin_unlock_irqrestore(&udc->lock, flags); | |
1310 | return 0; | |
1311 | } | |
1312 | ||
1313 | static struct usb_gadget_ops omap_gadget_ops = { | |
1314 | .get_frame = omap_get_frame, | |
1315 | .wakeup = omap_wakeup, | |
1316 | .set_selfpowered = omap_set_selfpowered, | |
1317 | .vbus_session = omap_vbus_session, | |
1318 | .vbus_draw = omap_vbus_draw, | |
1319 | .pullup = omap_pullup, | |
1320 | }; | |
1321 | ||
1322 | /*-------------------------------------------------------------------------*/ | |
1323 | ||
1324 | /* dequeue ALL requests; caller holds udc->lock */ | |
1325 | static void nuke(struct omap_ep *ep, int status) | |
1326 | { | |
1327 | struct omap_req *req; | |
1328 | ||
1329 | ep->stopped = 1; | |
1330 | ||
1331 | if (use_dma && ep->dma_channel) | |
1332 | dma_channel_release(ep); | |
1333 | ||
1334 | use_ep(ep, 0); | |
1335 | UDC_CTRL_REG = UDC_CLR_EP; | |
1336 | if (ep->bEndpointAddress && ep->bmAttributes != USB_ENDPOINT_XFER_ISOC) | |
1337 | UDC_CTRL_REG = UDC_SET_HALT; | |
1338 | ||
1339 | while (!list_empty(&ep->queue)) { | |
1340 | req = list_entry(ep->queue.next, struct omap_req, queue); | |
1341 | done(ep, req, status); | |
1342 | } | |
1343 | } | |
1344 | ||
1345 | /* caller holds udc->lock */ | |
1346 | static void udc_quiesce(struct omap_udc *udc) | |
1347 | { | |
1348 | struct omap_ep *ep; | |
1349 | ||
1350 | udc->gadget.speed = USB_SPEED_UNKNOWN; | |
1351 | nuke(&udc->ep[0], -ESHUTDOWN); | |
1352 | list_for_each_entry (ep, &udc->gadget.ep_list, ep.ep_list) | |
1353 | nuke(ep, -ESHUTDOWN); | |
1354 | } | |
1355 | ||
1356 | /*-------------------------------------------------------------------------*/ | |
1357 | ||
1358 | static void update_otg(struct omap_udc *udc) | |
1359 | { | |
1360 | u16 devstat; | |
1361 | ||
1362 | if (!udc->gadget.is_otg) | |
1363 | return; | |
1364 | ||
1365 | if (OTG_CTRL_REG & OTG_ID) | |
1366 | devstat = UDC_DEVSTAT_REG; | |
1367 | else | |
1368 | devstat = 0; | |
1369 | ||
1370 | udc->gadget.b_hnp_enable = !!(devstat & UDC_B_HNP_ENABLE); | |
1371 | udc->gadget.a_hnp_support = !!(devstat & UDC_A_HNP_SUPPORT); | |
1372 | udc->gadget.a_alt_hnp_support = !!(devstat & UDC_A_ALT_HNP_SUPPORT); | |
1373 | ||
1374 | /* Enable HNP early, avoiding races on suspend irq path. | |
1375 | * ASSUMES OTG state machine B_BUS_REQ input is true. | |
1376 | */ | |
1377 | if (udc->gadget.b_hnp_enable) | |
1378 | OTG_CTRL_REG = (OTG_CTRL_REG | OTG_B_HNPEN | OTG_B_BUSREQ) | |
1379 | & ~OTG_PULLUP; | |
1380 | } | |
1381 | ||
1382 | static void ep0_irq(struct omap_udc *udc, u16 irq_src) | |
1383 | { | |
1384 | struct omap_ep *ep0 = &udc->ep[0]; | |
1385 | struct omap_req *req = 0; | |
1386 | ||
1387 | ep0->irqs++; | |
1388 | ||
1389 | /* Clear any pending requests and then scrub any rx/tx state | |
1390 | * before starting to handle the SETUP request. | |
1391 | */ | |
1392 | if (irq_src & UDC_SETUP) { | |
1393 | u16 ack = irq_src & (UDC_EP0_TX|UDC_EP0_RX); | |
1394 | ||
1395 | nuke(ep0, 0); | |
1396 | if (ack) { | |
1397 | UDC_IRQ_SRC_REG = ack; | |
1398 | irq_src = UDC_SETUP; | |
1399 | } | |
1400 | } | |
1401 | ||
1402 | /* IN/OUT packets mean we're in the DATA or STATUS stage. | |
1403 | * This driver uses only uses protocol stalls (ep0 never halts), | |
1404 | * and if we got this far the gadget driver already had a | |
1405 | * chance to stall. Tries to be forgiving of host oddities. | |
1406 | * | |
1407 | * NOTE: the last chance gadget drivers have to stall control | |
1408 | * requests is during their request completion callback. | |
1409 | */ | |
1410 | if (!list_empty(&ep0->queue)) | |
1411 | req = container_of(ep0->queue.next, struct omap_req, queue); | |
1412 | ||
1413 | /* IN == TX to host */ | |
1414 | if (irq_src & UDC_EP0_TX) { | |
1415 | int stat; | |
1416 | ||
1417 | UDC_IRQ_SRC_REG = UDC_EP0_TX; | |
1418 | UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; | |
1419 | stat = UDC_STAT_FLG_REG; | |
1420 | if (stat & UDC_ACK) { | |
1421 | if (udc->ep0_in) { | |
1422 | /* write next IN packet from response, | |
1423 | * or set up the status stage. | |
1424 | */ | |
1425 | if (req) | |
1426 | stat = write_fifo(ep0, req); | |
1427 | UDC_EP_NUM_REG = UDC_EP_DIR; | |
1428 | if (!req && udc->ep0_pending) { | |
1429 | UDC_EP_NUM_REG = UDC_EP_SEL; | |
1430 | UDC_CTRL_REG = UDC_CLR_EP; | |
1431 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1432 | UDC_EP_NUM_REG = 0; | |
1433 | udc->ep0_pending = 0; | |
1434 | } /* else: 6 wait states before it'll tx */ | |
1435 | } else { | |
1436 | /* ack status stage of OUT transfer */ | |
1437 | UDC_EP_NUM_REG = UDC_EP_DIR; | |
1438 | if (req) | |
1439 | done(ep0, req, 0); | |
1440 | } | |
1441 | req = 0; | |
1442 | } else if (stat & UDC_STALL) { | |
1443 | UDC_CTRL_REG = UDC_CLR_HALT; | |
1444 | UDC_EP_NUM_REG = UDC_EP_DIR; | |
1445 | } else { | |
1446 | UDC_EP_NUM_REG = UDC_EP_DIR; | |
1447 | } | |
1448 | } | |
1449 | ||
1450 | /* OUT == RX from host */ | |
1451 | if (irq_src & UDC_EP0_RX) { | |
1452 | int stat; | |
1453 | ||
1454 | UDC_IRQ_SRC_REG = UDC_EP0_RX; | |
1455 | UDC_EP_NUM_REG = UDC_EP_SEL; | |
1456 | stat = UDC_STAT_FLG_REG; | |
1457 | if (stat & UDC_ACK) { | |
1458 | if (!udc->ep0_in) { | |
1459 | stat = 0; | |
1460 | /* read next OUT packet of request, maybe | |
1461 | * reactiviting the fifo; stall on errors. | |
1462 | */ | |
1463 | if (!req || (stat = read_fifo(ep0, req)) < 0) { | |
1464 | UDC_SYSCON2_REG = UDC_STALL_CMD; | |
1465 | udc->ep0_pending = 0; | |
1466 | stat = 0; | |
1467 | } else if (stat == 0) | |
1468 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1469 | UDC_EP_NUM_REG = 0; | |
1470 | ||
1471 | /* activate status stage */ | |
1472 | if (stat == 1) { | |
1473 | done(ep0, req, 0); | |
1474 | /* that may have STALLed ep0... */ | |
1475 | UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; | |
1476 | UDC_CTRL_REG = UDC_CLR_EP; | |
1477 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1478 | UDC_EP_NUM_REG = UDC_EP_DIR; | |
1479 | udc->ep0_pending = 0; | |
1480 | } | |
1481 | } else { | |
1482 | /* ack status stage of IN transfer */ | |
1483 | UDC_EP_NUM_REG = 0; | |
1484 | if (req) | |
1485 | done(ep0, req, 0); | |
1486 | } | |
1487 | } else if (stat & UDC_STALL) { | |
1488 | UDC_CTRL_REG = UDC_CLR_HALT; | |
1489 | UDC_EP_NUM_REG = 0; | |
1490 | } else { | |
1491 | UDC_EP_NUM_REG = 0; | |
1492 | } | |
1493 | } | |
1494 | ||
1495 | /* SETUP starts all control transfers */ | |
1496 | if (irq_src & UDC_SETUP) { | |
1497 | union u { | |
1498 | u16 word[4]; | |
1499 | struct usb_ctrlrequest r; | |
1500 | } u; | |
1501 | int status = -EINVAL; | |
1502 | struct omap_ep *ep; | |
1503 | ||
1504 | /* read the (latest) SETUP message */ | |
1505 | do { | |
1506 | UDC_EP_NUM_REG = UDC_SETUP_SEL; | |
1507 | /* two bytes at a time */ | |
1508 | u.word[0] = UDC_DATA_REG; | |
1509 | u.word[1] = UDC_DATA_REG; | |
1510 | u.word[2] = UDC_DATA_REG; | |
1511 | u.word[3] = UDC_DATA_REG; | |
1512 | UDC_EP_NUM_REG = 0; | |
1513 | } while (UDC_IRQ_SRC_REG & UDC_SETUP); | |
1514 | le16_to_cpus (&u.r.wValue); | |
1515 | le16_to_cpus (&u.r.wIndex); | |
1516 | le16_to_cpus (&u.r.wLength); | |
1517 | ||
1518 | /* Delegate almost all control requests to the gadget driver, | |
1519 | * except for a handful of ch9 status/feature requests that | |
1520 | * hardware doesn't autodecode _and_ the gadget API hides. | |
1521 | */ | |
1522 | udc->ep0_in = (u.r.bRequestType & USB_DIR_IN) != 0; | |
1523 | udc->ep0_set_config = 0; | |
1524 | udc->ep0_pending = 1; | |
1525 | ep0->stopped = 0; | |
1526 | ep0->ackwait = 0; | |
1527 | switch (u.r.bRequest) { | |
1528 | case USB_REQ_SET_CONFIGURATION: | |
1529 | /* udc needs to know when ep != 0 is valid */ | |
1530 | if (u.r.bRequestType != USB_RECIP_DEVICE) | |
1531 | goto delegate; | |
1532 | if (u.r.wLength != 0) | |
1533 | goto do_stall; | |
1534 | udc->ep0_set_config = 1; | |
1535 | udc->ep0_reset_config = (u.r.wValue == 0); | |
1536 | VDBG("set config %d\n", u.r.wValue); | |
1537 | ||
1538 | /* update udc NOW since gadget driver may start | |
1539 | * queueing requests immediately; clear config | |
1540 | * later if it fails the request. | |
1541 | */ | |
1542 | if (udc->ep0_reset_config) | |
1543 | UDC_SYSCON2_REG = UDC_CLR_CFG; | |
1544 | else | |
1545 | UDC_SYSCON2_REG = UDC_DEV_CFG; | |
1546 | update_otg(udc); | |
1547 | goto delegate; | |
1548 | case USB_REQ_CLEAR_FEATURE: | |
1549 | /* clear endpoint halt */ | |
1550 | if (u.r.bRequestType != USB_RECIP_ENDPOINT) | |
1551 | goto delegate; | |
1552 | if (u.r.wValue != USB_ENDPOINT_HALT | |
1553 | || u.r.wLength != 0) | |
1554 | goto do_stall; | |
1555 | ep = &udc->ep[u.r.wIndex & 0xf]; | |
1556 | if (ep != ep0) { | |
1557 | if (u.r.wIndex & USB_DIR_IN) | |
1558 | ep += 16; | |
1559 | if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC | |
1560 | || !ep->desc) | |
1561 | goto do_stall; | |
1562 | use_ep(ep, 0); | |
1563 | UDC_CTRL_REG = UDC_RESET_EP; | |
1564 | ep->ackwait = 0; | |
1565 | if (!(ep->bEndpointAddress & USB_DIR_IN)) { | |
1566 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1567 | ep->ackwait = 1 + ep->double_buf; | |
1568 | } | |
1569 | } | |
1570 | VDBG("%s halt cleared by host\n", ep->name); | |
1571 | goto ep0out_status_stage; | |
1572 | case USB_REQ_SET_FEATURE: | |
1573 | /* set endpoint halt */ | |
1574 | if (u.r.bRequestType != USB_RECIP_ENDPOINT) | |
1575 | goto delegate; | |
1576 | if (u.r.wValue != USB_ENDPOINT_HALT | |
1577 | || u.r.wLength != 0) | |
1578 | goto do_stall; | |
1579 | ep = &udc->ep[u.r.wIndex & 0xf]; | |
1580 | if (u.r.wIndex & USB_DIR_IN) | |
1581 | ep += 16; | |
1582 | if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC | |
1583 | || ep == ep0 || !ep->desc) | |
1584 | goto do_stall; | |
1585 | if (use_dma && ep->has_dma) { | |
1586 | /* this has rude side-effects (aborts) and | |
1587 | * can't really work if DMA-IN is active | |
1588 | */ | |
1589 | DBG("%s host set_halt, NYET \n", ep->name); | |
1590 | goto do_stall; | |
1591 | } | |
1592 | use_ep(ep, 0); | |
1593 | /* can't halt if fifo isn't empty... */ | |
1594 | UDC_CTRL_REG = UDC_CLR_EP; | |
1595 | UDC_CTRL_REG = UDC_SET_HALT; | |
1596 | VDBG("%s halted by host\n", ep->name); | |
1597 | ep0out_status_stage: | |
1598 | status = 0; | |
1599 | UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; | |
1600 | UDC_CTRL_REG = UDC_CLR_EP; | |
1601 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1602 | UDC_EP_NUM_REG = UDC_EP_DIR; | |
1603 | udc->ep0_pending = 0; | |
1604 | break; | |
1605 | case USB_REQ_GET_STATUS: | |
1606 | /* return interface status. if we were pedantic, | |
1607 | * we'd detect non-existent interfaces, and stall. | |
1608 | */ | |
1609 | if (u.r.bRequestType | |
1610 | != (USB_DIR_IN|USB_RECIP_INTERFACE)) | |
1611 | goto delegate; | |
1612 | /* return two zero bytes */ | |
1613 | UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; | |
1614 | UDC_DATA_REG = 0; | |
1615 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1616 | UDC_EP_NUM_REG = UDC_EP_DIR; | |
1617 | status = 0; | |
1618 | VDBG("GET_STATUS, interface %d\n", u.r.wIndex); | |
1619 | /* next, status stage */ | |
1620 | break; | |
1621 | default: | |
1622 | delegate: | |
1623 | /* activate the ep0out fifo right away */ | |
1624 | if (!udc->ep0_in && u.r.wLength) { | |
1625 | UDC_EP_NUM_REG = 0; | |
1626 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1627 | } | |
1628 | ||
1629 | /* gadget drivers see class/vendor specific requests, | |
1630 | * {SET,GET}_{INTERFACE,DESCRIPTOR,CONFIGURATION}, | |
1631 | * and more | |
1632 | */ | |
1633 | VDBG("SETUP %02x.%02x v%04x i%04x l%04x\n", | |
1634 | u.r.bRequestType, u.r.bRequest, | |
1635 | u.r.wValue, u.r.wIndex, u.r.wLength); | |
1636 | ||
1637 | /* The gadget driver may return an error here, | |
1638 | * causing an immediate protocol stall. | |
1639 | * | |
1640 | * Else it must issue a response, either queueing a | |
1641 | * response buffer for the DATA stage, or halting ep0 | |
1642 | * (causing a protocol stall, not a real halt). A | |
1643 | * zero length buffer means no DATA stage. | |
1644 | * | |
1645 | * It's fine to issue that response after the setup() | |
1646 | * call returns, and this IRQ was handled. | |
1647 | */ | |
1648 | udc->ep0_setup = 1; | |
1649 | spin_unlock(&udc->lock); | |
1650 | status = udc->driver->setup (&udc->gadget, &u.r); | |
1651 | spin_lock(&udc->lock); | |
1652 | udc->ep0_setup = 0; | |
1653 | } | |
1654 | ||
1655 | if (status < 0) { | |
1656 | do_stall: | |
1657 | VDBG("req %02x.%02x protocol STALL; stat %d\n", | |
1658 | u.r.bRequestType, u.r.bRequest, status); | |
1659 | if (udc->ep0_set_config) { | |
1660 | if (udc->ep0_reset_config) | |
1661 | WARN("error resetting config?\n"); | |
1662 | else | |
1663 | UDC_SYSCON2_REG = UDC_CLR_CFG; | |
1664 | } | |
1665 | UDC_SYSCON2_REG = UDC_STALL_CMD; | |
1666 | udc->ep0_pending = 0; | |
1667 | } | |
1668 | } | |
1669 | } | |
1670 | ||
1671 | /*-------------------------------------------------------------------------*/ | |
1672 | ||
1673 | #define OTG_FLAGS (UDC_B_HNP_ENABLE|UDC_A_HNP_SUPPORT|UDC_A_ALT_HNP_SUPPORT) | |
1674 | ||
1675 | static void devstate_irq(struct omap_udc *udc, u16 irq_src) | |
1676 | { | |
1677 | u16 devstat, change; | |
1678 | ||
1679 | devstat = UDC_DEVSTAT_REG; | |
1680 | change = devstat ^ udc->devstat; | |
1681 | udc->devstat = devstat; | |
1682 | ||
1683 | if (change & (UDC_USB_RESET|UDC_ATT)) { | |
1684 | udc_quiesce(udc); | |
1685 | ||
1686 | if (change & UDC_ATT) { | |
1687 | /* driver for any external transceiver will | |
1688 | * have called omap_vbus_session() already | |
1689 | */ | |
1690 | if (devstat & UDC_ATT) { | |
1691 | udc->gadget.speed = USB_SPEED_FULL; | |
1692 | VDBG("connect\n"); | |
1693 | if (!udc->transceiver) | |
1694 | pullup_enable(udc); | |
1695 | // if (driver->connect) call it | |
1696 | } else if (udc->gadget.speed != USB_SPEED_UNKNOWN) { | |
1697 | udc->gadget.speed = USB_SPEED_UNKNOWN; | |
1698 | if (!udc->transceiver) | |
1699 | pullup_disable(udc); | |
1700 | DBG("disconnect, gadget %s\n", | |
1701 | udc->driver->driver.name); | |
1702 | if (udc->driver->disconnect) { | |
1703 | spin_unlock(&udc->lock); | |
1704 | udc->driver->disconnect(&udc->gadget); | |
1705 | spin_lock(&udc->lock); | |
1706 | } | |
1707 | } | |
1708 | change &= ~UDC_ATT; | |
1709 | } | |
1710 | ||
1711 | if (change & UDC_USB_RESET) { | |
1712 | if (devstat & UDC_USB_RESET) { | |
1713 | VDBG("RESET=1\n"); | |
1714 | } else { | |
1715 | udc->gadget.speed = USB_SPEED_FULL; | |
1716 | INFO("USB reset done, gadget %s\n", | |
1717 | udc->driver->driver.name); | |
1718 | /* ep0 traffic is legal from now on */ | |
1719 | UDC_IRQ_EN_REG = UDC_DS_CHG_IE | UDC_EP0_IE; | |
1720 | } | |
1721 | change &= ~UDC_USB_RESET; | |
1722 | } | |
1723 | } | |
1724 | if (change & UDC_SUS) { | |
1725 | if (udc->gadget.speed != USB_SPEED_UNKNOWN) { | |
1726 | // FIXME tell isp1301 to suspend/resume (?) | |
1727 | if (devstat & UDC_SUS) { | |
1728 | VDBG("suspend\n"); | |
1729 | update_otg(udc); | |
1730 | /* HNP could be under way already */ | |
1731 | if (udc->gadget.speed == USB_SPEED_FULL | |
1732 | && udc->driver->suspend) { | |
1733 | spin_unlock(&udc->lock); | |
1734 | udc->driver->suspend(&udc->gadget); | |
1735 | spin_lock(&udc->lock); | |
1736 | } | |
1737 | } else { | |
1738 | VDBG("resume\n"); | |
1739 | if (udc->gadget.speed == USB_SPEED_FULL | |
1740 | && udc->driver->resume) { | |
1741 | spin_unlock(&udc->lock); | |
1742 | udc->driver->resume(&udc->gadget); | |
1743 | spin_lock(&udc->lock); | |
1744 | } | |
1745 | } | |
1746 | } | |
1747 | change &= ~UDC_SUS; | |
1748 | } | |
1749 | if (!cpu_is_omap15xx() && (change & OTG_FLAGS)) { | |
1750 | update_otg(udc); | |
1751 | change &= ~OTG_FLAGS; | |
1752 | } | |
1753 | ||
1754 | change &= ~(UDC_CFG|UDC_DEF|UDC_ADD); | |
1755 | if (change) | |
1756 | VDBG("devstat %03x, ignore change %03x\n", | |
1757 | devstat, change); | |
1758 | ||
1759 | UDC_IRQ_SRC_REG = UDC_DS_CHG; | |
1760 | } | |
1761 | ||
1762 | static irqreturn_t | |
1763 | omap_udc_irq(int irq, void *_udc, struct pt_regs *r) | |
1764 | { | |
1765 | struct omap_udc *udc = _udc; | |
1766 | u16 irq_src; | |
1767 | irqreturn_t status = IRQ_NONE; | |
1768 | unsigned long flags; | |
1769 | ||
1770 | spin_lock_irqsave(&udc->lock, flags); | |
1771 | irq_src = UDC_IRQ_SRC_REG; | |
1772 | ||
1773 | /* Device state change (usb ch9 stuff) */ | |
1774 | if (irq_src & UDC_DS_CHG) { | |
1775 | devstate_irq(_udc, irq_src); | |
1776 | status = IRQ_HANDLED; | |
1777 | irq_src &= ~UDC_DS_CHG; | |
1778 | } | |
1779 | ||
1780 | /* EP0 control transfers */ | |
1781 | if (irq_src & (UDC_EP0_RX|UDC_SETUP|UDC_EP0_TX)) { | |
1782 | ep0_irq(_udc, irq_src); | |
1783 | status = IRQ_HANDLED; | |
1784 | irq_src &= ~(UDC_EP0_RX|UDC_SETUP|UDC_EP0_TX); | |
1785 | } | |
1786 | ||
1787 | /* DMA transfer completion */ | |
1788 | if (use_dma && (irq_src & (UDC_TXN_DONE|UDC_RXN_CNT|UDC_RXN_EOT))) { | |
1789 | dma_irq(_udc, irq_src); | |
1790 | status = IRQ_HANDLED; | |
1791 | irq_src &= ~(UDC_TXN_DONE|UDC_RXN_CNT|UDC_RXN_EOT); | |
1792 | } | |
1793 | ||
1794 | irq_src &= ~(UDC_SOF|UDC_EPN_TX|UDC_EPN_RX); | |
1795 | if (irq_src) | |
1796 | DBG("udc_irq, unhandled %03x\n", irq_src); | |
1797 | spin_unlock_irqrestore(&udc->lock, flags); | |
1798 | ||
1799 | return status; | |
1800 | } | |
1801 | ||
1802 | /* workaround for seemingly-lost IRQs for RX ACKs... */ | |
1803 | #define PIO_OUT_TIMEOUT (jiffies + HZ/3) | |
1804 | #define HALF_FULL(f) (!((f)&(UDC_NON_ISO_FIFO_FULL|UDC_NON_ISO_FIFO_EMPTY))) | |
1805 | ||
1806 | static void pio_out_timer(unsigned long _ep) | |
1807 | { | |
1808 | struct omap_ep *ep = (void *) _ep; | |
1809 | unsigned long flags; | |
1810 | u16 stat_flg; | |
1811 | ||
1812 | spin_lock_irqsave(&ep->udc->lock, flags); | |
1813 | if (!list_empty(&ep->queue) && ep->ackwait) { | |
1814 | use_ep(ep, 0); | |
1815 | stat_flg = UDC_STAT_FLG_REG; | |
1816 | ||
1817 | if ((stat_flg & UDC_ACK) && (!(stat_flg & UDC_FIFO_EN) | |
1818 | || (ep->double_buf && HALF_FULL(stat_flg)))) { | |
1819 | struct omap_req *req; | |
1820 | ||
1821 | VDBG("%s: lose, %04x\n", ep->ep.name, stat_flg); | |
1822 | req = container_of(ep->queue.next, | |
1823 | struct omap_req, queue); | |
1824 | UDC_EP_NUM_REG = ep->bEndpointAddress | UDC_EP_SEL; | |
1825 | (void) read_fifo(ep, req); | |
1826 | UDC_EP_NUM_REG = ep->bEndpointAddress; | |
1827 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1828 | ep->ackwait = 1 + ep->double_buf; | |
1829 | } | |
1830 | } | |
1831 | mod_timer(&ep->timer, PIO_OUT_TIMEOUT); | |
1832 | spin_unlock_irqrestore(&ep->udc->lock, flags); | |
1833 | } | |
1834 | ||
1835 | static irqreturn_t | |
1836 | omap_udc_pio_irq(int irq, void *_dev, struct pt_regs *r) | |
1837 | { | |
1838 | u16 epn_stat, irq_src; | |
1839 | irqreturn_t status = IRQ_NONE; | |
1840 | struct omap_ep *ep; | |
1841 | int epnum; | |
1842 | struct omap_udc *udc = _dev; | |
1843 | struct omap_req *req; | |
1844 | unsigned long flags; | |
1845 | ||
1846 | spin_lock_irqsave(&udc->lock, flags); | |
1847 | epn_stat = UDC_EPN_STAT_REG; | |
1848 | irq_src = UDC_IRQ_SRC_REG; | |
1849 | ||
1850 | /* handle OUT first, to avoid some wasteful NAKs */ | |
1851 | if (irq_src & UDC_EPN_RX) { | |
1852 | epnum = (epn_stat >> 8) & 0x0f; | |
1853 | UDC_IRQ_SRC_REG = UDC_EPN_RX; | |
1854 | status = IRQ_HANDLED; | |
1855 | ep = &udc->ep[epnum]; | |
1856 | ep->irqs++; | |
1857 | ||
1858 | UDC_EP_NUM_REG = epnum | UDC_EP_SEL; | |
1859 | ep->fnf = 0; | |
1860 | if ((UDC_STAT_FLG_REG & UDC_ACK)) { | |
1861 | ep->ackwait--; | |
1862 | if (!list_empty(&ep->queue)) { | |
1863 | int stat; | |
1864 | req = container_of(ep->queue.next, | |
1865 | struct omap_req, queue); | |
1866 | stat = read_fifo(ep, req); | |
1867 | if (!ep->double_buf) | |
1868 | ep->fnf = 1; | |
1869 | } | |
1870 | } | |
1871 | /* min 6 clock delay before clearing EP_SEL ... */ | |
1872 | epn_stat = UDC_EPN_STAT_REG; | |
1873 | epn_stat = UDC_EPN_STAT_REG; | |
1874 | UDC_EP_NUM_REG = epnum; | |
1875 | ||
1876 | /* enabling fifo _after_ clearing ACK, contrary to docs, | |
1877 | * reduces lossage; timer still needed though (sigh). | |
1878 | */ | |
1879 | if (ep->fnf) { | |
1880 | UDC_CTRL_REG = UDC_SET_FIFO_EN; | |
1881 | ep->ackwait = 1 + ep->double_buf; | |
1882 | } | |
1883 | mod_timer(&ep->timer, PIO_OUT_TIMEOUT); | |
1884 | } | |
1885 | ||
1886 | /* then IN transfers */ | |
1887 | else if (irq_src & UDC_EPN_TX) { | |
1888 | epnum = epn_stat & 0x0f; | |
1889 | UDC_IRQ_SRC_REG = UDC_EPN_TX; | |
1890 | status = IRQ_HANDLED; | |
1891 | ep = &udc->ep[16 + epnum]; | |
1892 | ep->irqs++; | |
1893 | ||
1894 | UDC_EP_NUM_REG = epnum | UDC_EP_DIR | UDC_EP_SEL; | |
1895 | if ((UDC_STAT_FLG_REG & UDC_ACK)) { | |
1896 | ep->ackwait = 0; | |
1897 | if (!list_empty(&ep->queue)) { | |
1898 | req = container_of(ep->queue.next, | |
1899 | struct omap_req, queue); | |
1900 | (void) write_fifo(ep, req); | |
1901 | } | |
1902 | } | |
1903 | /* min 6 clock delay before clearing EP_SEL ... */ | |
1904 | epn_stat = UDC_EPN_STAT_REG; | |
1905 | epn_stat = UDC_EPN_STAT_REG; | |
1906 | UDC_EP_NUM_REG = epnum | UDC_EP_DIR; | |
1907 | /* then 6 clocks before it'd tx */ | |
1908 | } | |
1909 | ||
1910 | spin_unlock_irqrestore(&udc->lock, flags); | |
1911 | return status; | |
1912 | } | |
1913 | ||
1914 | #ifdef USE_ISO | |
1915 | static irqreturn_t | |
1916 | omap_udc_iso_irq(int irq, void *_dev, struct pt_regs *r) | |
1917 | { | |
1918 | struct omap_udc *udc = _dev; | |
1919 | struct omap_ep *ep; | |
1920 | int pending = 0; | |
1921 | unsigned long flags; | |
1922 | ||
1923 | spin_lock_irqsave(&udc->lock, flags); | |
1924 | ||
1925 | /* handle all non-DMA ISO transfers */ | |
1926 | list_for_each_entry (ep, &udc->iso, iso) { | |
1927 | u16 stat; | |
1928 | struct omap_req *req; | |
1929 | ||
1930 | if (ep->has_dma || list_empty(&ep->queue)) | |
1931 | continue; | |
1932 | req = list_entry(ep->queue.next, struct omap_req, queue); | |
1933 | ||
1934 | use_ep(ep, UDC_EP_SEL); | |
1935 | stat = UDC_STAT_FLG_REG; | |
1936 | ||
1937 | /* NOTE: like the other controller drivers, this isn't | |
1938 | * currently reporting lost or damaged frames. | |
1939 | */ | |
1940 | if (ep->bEndpointAddress & USB_DIR_IN) { | |
1941 | if (stat & UDC_MISS_IN) | |
1942 | /* done(ep, req, -EPROTO) */; | |
1943 | else | |
1944 | write_fifo(ep, req); | |
1945 | } else { | |
1946 | int status = 0; | |
1947 | ||
1948 | if (stat & UDC_NO_RXPACKET) | |
1949 | status = -EREMOTEIO; | |
1950 | else if (stat & UDC_ISO_ERR) | |
1951 | status = -EILSEQ; | |
1952 | else if (stat & UDC_DATA_FLUSH) | |
1953 | status = -ENOSR; | |
1954 | ||
1955 | if (status) | |
1956 | /* done(ep, req, status) */; | |
1957 | else | |
1958 | read_fifo(ep, req); | |
1959 | } | |
1960 | deselect_ep(); | |
1961 | /* 6 wait states before next EP */ | |
1962 | ||
1963 | ep->irqs++; | |
1964 | if (!list_empty(&ep->queue)) | |
1965 | pending = 1; | |
1966 | } | |
1967 | if (!pending) | |
1968 | UDC_IRQ_EN_REG &= ~UDC_SOF_IE; | |
1969 | UDC_IRQ_SRC_REG = UDC_SOF; | |
1970 | ||
1971 | spin_unlock_irqrestore(&udc->lock, flags); | |
1972 | return IRQ_HANDLED; | |
1973 | } | |
1974 | #endif | |
1975 | ||
1976 | /*-------------------------------------------------------------------------*/ | |
1977 | ||
1978 | static struct omap_udc *udc; | |
1979 | ||
1980 | int usb_gadget_register_driver (struct usb_gadget_driver *driver) | |
1981 | { | |
1982 | int status = -ENODEV; | |
1983 | struct omap_ep *ep; | |
1984 | unsigned long flags; | |
1985 | ||
1986 | /* basic sanity tests */ | |
1987 | if (!udc) | |
1988 | return -ENODEV; | |
1989 | if (!driver | |
1990 | // FIXME if otg, check: driver->is_otg | |
1991 | || driver->speed < USB_SPEED_FULL | |
1992 | || !driver->bind | |
1993 | || !driver->unbind | |
1994 | || !driver->setup) | |
1995 | return -EINVAL; | |
1996 | ||
1997 | spin_lock_irqsave(&udc->lock, flags); | |
1998 | if (udc->driver) { | |
1999 | spin_unlock_irqrestore(&udc->lock, flags); | |
2000 | return -EBUSY; | |
2001 | } | |
2002 | ||
2003 | /* reset state */ | |
2004 | list_for_each_entry (ep, &udc->gadget.ep_list, ep.ep_list) { | |
2005 | ep->irqs = 0; | |
2006 | if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) | |
2007 | continue; | |
2008 | use_ep(ep, 0); | |
2009 | UDC_CTRL_REG = UDC_SET_HALT; | |
2010 | } | |
2011 | udc->ep0_pending = 0; | |
2012 | udc->ep[0].irqs = 0; | |
2013 | udc->softconnect = 1; | |
2014 | ||
2015 | /* hook up the driver */ | |
2016 | driver->driver.bus = 0; | |
2017 | udc->driver = driver; | |
2018 | udc->gadget.dev.driver = &driver->driver; | |
2019 | spin_unlock_irqrestore(&udc->lock, flags); | |
2020 | ||
2021 | status = driver->bind (&udc->gadget); | |
2022 | if (status) { | |
2023 | DBG("bind to %s --> %d\n", driver->driver.name, status); | |
2024 | udc->gadget.dev.driver = 0; | |
2025 | udc->driver = 0; | |
2026 | goto done; | |
2027 | } | |
2028 | DBG("bound to driver %s\n", driver->driver.name); | |
2029 | ||
2030 | UDC_IRQ_SRC_REG = UDC_IRQ_SRC_MASK; | |
2031 | ||
2032 | /* connect to bus through transceiver */ | |
2033 | if (udc->transceiver) { | |
2034 | status = otg_set_peripheral(udc->transceiver, &udc->gadget); | |
2035 | if (status < 0) { | |
2036 | ERR("can't bind to transceiver\n"); | |
2037 | driver->unbind (&udc->gadget); | |
2038 | udc->gadget.dev.driver = 0; | |
2039 | udc->driver = 0; | |
2040 | goto done; | |
2041 | } | |
2042 | } else { | |
2043 | if (can_pullup(udc)) | |
2044 | pullup_enable (udc); | |
2045 | else | |
2046 | pullup_disable (udc); | |
2047 | } | |
2048 | ||
2049 | /* boards that don't have VBUS sensing can't autogate 48MHz; | |
2050 | * can't enter deep sleep while a gadget driver is active. | |
2051 | */ | |
2052 | if (machine_is_omap_innovator() || machine_is_omap_osk()) | |
2053 | omap_vbus_session(&udc->gadget, 1); | |
2054 | ||
2055 | done: | |
2056 | return status; | |
2057 | } | |
2058 | EXPORT_SYMBOL(usb_gadget_register_driver); | |
2059 | ||
2060 | int usb_gadget_unregister_driver (struct usb_gadget_driver *driver) | |
2061 | { | |
2062 | unsigned long flags; | |
2063 | int status = -ENODEV; | |
2064 | ||
2065 | if (!udc) | |
2066 | return -ENODEV; | |
2067 | if (!driver || driver != udc->driver) | |
2068 | return -EINVAL; | |
2069 | ||
2070 | if (machine_is_omap_innovator() || machine_is_omap_osk()) | |
2071 | omap_vbus_session(&udc->gadget, 0); | |
2072 | ||
2073 | if (udc->transceiver) | |
2074 | (void) otg_set_peripheral(udc->transceiver, 0); | |
2075 | else | |
2076 | pullup_disable(udc); | |
2077 | ||
2078 | spin_lock_irqsave(&udc->lock, flags); | |
2079 | udc_quiesce(udc); | |
2080 | spin_unlock_irqrestore(&udc->lock, flags); | |
2081 | ||
2082 | driver->unbind(&udc->gadget); | |
2083 | udc->gadget.dev.driver = 0; | |
2084 | udc->driver = 0; | |
2085 | ||
2086 | ||
2087 | DBG("unregistered driver '%s'\n", driver->driver.name); | |
2088 | return status; | |
2089 | } | |
2090 | EXPORT_SYMBOL(usb_gadget_unregister_driver); | |
2091 | ||
2092 | ||
2093 | /*-------------------------------------------------------------------------*/ | |
2094 | ||
2095 | #ifdef CONFIG_USB_GADGET_DEBUG_FILES | |
2096 | ||
2097 | #include <linux/seq_file.h> | |
2098 | ||
2099 | static const char proc_filename[] = "driver/udc"; | |
2100 | ||
2101 | #define FOURBITS "%s%s%s%s" | |
2102 | #define EIGHTBITS FOURBITS FOURBITS | |
2103 | ||
2104 | static void proc_ep_show(struct seq_file *s, struct omap_ep *ep) | |
2105 | { | |
2106 | u16 stat_flg; | |
2107 | struct omap_req *req; | |
2108 | char buf[20]; | |
2109 | ||
2110 | use_ep(ep, 0); | |
2111 | ||
2112 | if (use_dma && ep->has_dma) | |
2113 | snprintf(buf, sizeof buf, "(%cxdma%d lch%d) ", | |
2114 | (ep->bEndpointAddress & USB_DIR_IN) ? 't' : 'r', | |
2115 | ep->dma_channel - 1, ep->lch); | |
2116 | else | |
2117 | buf[0] = 0; | |
2118 | ||
2119 | stat_flg = UDC_STAT_FLG_REG; | |
2120 | seq_printf(s, | |
2121 | "\n%s %s%s%sirqs %ld stat %04x " EIGHTBITS FOURBITS "%s\n", | |
2122 | ep->name, buf, | |
2123 | ep->double_buf ? "dbuf " : "", | |
2124 | ({char *s; switch(ep->ackwait){ | |
2125 | case 0: s = ""; break; | |
2126 | case 1: s = "(ackw) "; break; | |
2127 | case 2: s = "(ackw2) "; break; | |
2128 | default: s = "(?) "; break; | |
2129 | } s;}), | |
2130 | ep->irqs, stat_flg, | |
2131 | (stat_flg & UDC_NO_RXPACKET) ? "no_rxpacket " : "", | |
2132 | (stat_flg & UDC_MISS_IN) ? "miss_in " : "", | |
2133 | (stat_flg & UDC_DATA_FLUSH) ? "data_flush " : "", | |
2134 | (stat_flg & UDC_ISO_ERR) ? "iso_err " : "", | |
2135 | (stat_flg & UDC_ISO_FIFO_EMPTY) ? "iso_fifo_empty " : "", | |
2136 | (stat_flg & UDC_ISO_FIFO_FULL) ? "iso_fifo_full " : "", | |
2137 | (stat_flg & UDC_EP_HALTED) ? "HALT " : "", | |
2138 | (stat_flg & UDC_STALL) ? "STALL " : "", | |
2139 | (stat_flg & UDC_NAK) ? "NAK " : "", | |
2140 | (stat_flg & UDC_ACK) ? "ACK " : "", | |
2141 | (stat_flg & UDC_FIFO_EN) ? "fifo_en " : "", | |
2142 | (stat_flg & UDC_NON_ISO_FIFO_EMPTY) ? "fifo_empty " : "", | |
2143 | (stat_flg & UDC_NON_ISO_FIFO_FULL) ? "fifo_full " : ""); | |
2144 | ||
2145 | if (list_empty (&ep->queue)) | |
2146 | seq_printf(s, "\t(queue empty)\n"); | |
2147 | else | |
2148 | list_for_each_entry (req, &ep->queue, queue) { | |
2149 | unsigned length = req->req.actual; | |
2150 | ||
2151 | if (use_dma && buf[0]) { | |
2152 | length += ((ep->bEndpointAddress & USB_DIR_IN) | |
2153 | ? dma_src_len : dma_dest_len) | |
2154 | (ep, req->req.dma + length); | |
2155 | buf[0] = 0; | |
2156 | } | |
2157 | seq_printf(s, "\treq %p len %d/%d buf %p\n", | |
2158 | &req->req, length, | |
2159 | req->req.length, req->req.buf); | |
2160 | } | |
2161 | } | |
2162 | ||
2163 | static char *trx_mode(unsigned m, int enabled) | |
2164 | { | |
2165 | switch (m) { | |
2166 | case 0: return enabled ? "*6wire" : "unused"; | |
2167 | case 1: return "4wire"; | |
2168 | case 2: return "3wire"; | |
2169 | case 3: return "6wire"; | |
2170 | default: return "unknown"; | |
2171 | } | |
2172 | } | |
2173 | ||
2174 | static int proc_otg_show(struct seq_file *s) | |
2175 | { | |
2176 | u32 tmp; | |
2177 | u32 trans; | |
2178 | ||
2179 | tmp = OTG_REV_REG; | |
2180 | trans = USB_TRANSCEIVER_CTRL_REG; | |
2181 | seq_printf(s, "OTG rev %d.%d, transceiver_ctrl %03x\n", | |
2182 | tmp >> 4, tmp & 0xf, trans); | |
2183 | tmp = OTG_SYSCON_1_REG; | |
2184 | seq_printf(s, "otg_syscon1 %08x usb2 %s, usb1 %s, usb0 %s," | |
2185 | FOURBITS "\n", tmp, | |
2186 | trx_mode(USB2_TRX_MODE(tmp), trans & CONF_USB2_UNI_R), | |
2187 | trx_mode(USB1_TRX_MODE(tmp), trans & CONF_USB1_UNI_R), | |
2188 | (USB0_TRX_MODE(tmp) == 0) | |
2189 | ? "internal" | |
2190 | : trx_mode(USB0_TRX_MODE(tmp), 1), | |
2191 | (tmp & OTG_IDLE_EN) ? " !otg" : "", | |
2192 | (tmp & HST_IDLE_EN) ? " !host" : "", | |
2193 | (tmp & DEV_IDLE_EN) ? " !dev" : "", | |
2194 | (tmp & OTG_RESET_DONE) ? " reset_done" : " reset_active"); | |
2195 | tmp = OTG_SYSCON_2_REG; | |
2196 | seq_printf(s, "otg_syscon2 %08x%s" EIGHTBITS | |
2197 | " b_ase_brst=%d hmc=%d\n", tmp, | |
2198 | (tmp & OTG_EN) ? " otg_en" : "", | |
2199 | (tmp & USBX_SYNCHRO) ? " synchro" : "", | |
2200 | // much more SRP stuff | |
2201 | (tmp & SRP_DATA) ? " srp_data" : "", | |
2202 | (tmp & SRP_VBUS) ? " srp_vbus" : "", | |
2203 | (tmp & OTG_PADEN) ? " otg_paden" : "", | |
2204 | (tmp & HMC_PADEN) ? " hmc_paden" : "", | |
2205 | (tmp & UHOST_EN) ? " uhost_en" : "", | |
2206 | (tmp & HMC_TLLSPEED) ? " tllspeed" : "", | |
2207 | (tmp & HMC_TLLATTACH) ? " tllattach" : "", | |
2208 | B_ASE_BRST(tmp), | |
2209 | OTG_HMC(tmp)); | |
2210 | tmp = OTG_CTRL_REG; | |
2211 | seq_printf(s, "otg_ctrl %06x" EIGHTBITS EIGHTBITS "%s\n", tmp, | |
2212 | (tmp & OTG_ASESSVLD) ? " asess" : "", | |
2213 | (tmp & OTG_BSESSEND) ? " bsess_end" : "", | |
2214 | (tmp & OTG_BSESSVLD) ? " bsess" : "", | |
2215 | (tmp & OTG_VBUSVLD) ? " vbus" : "", | |
2216 | (tmp & OTG_ID) ? " id" : "", | |
2217 | (tmp & OTG_DRIVER_SEL) ? " DEVICE" : " HOST", | |
2218 | (tmp & OTG_A_SETB_HNPEN) ? " a_setb_hnpen" : "", | |
2219 | (tmp & OTG_A_BUSREQ) ? " a_bus" : "", | |
2220 | (tmp & OTG_B_HNPEN) ? " b_hnpen" : "", | |
2221 | (tmp & OTG_B_BUSREQ) ? " b_bus" : "", | |
2222 | (tmp & OTG_BUSDROP) ? " busdrop" : "", | |
2223 | (tmp & OTG_PULLDOWN) ? " down" : "", | |
2224 | (tmp & OTG_PULLUP) ? " up" : "", | |
2225 | (tmp & OTG_DRV_VBUS) ? " drv" : "", | |
2226 | (tmp & OTG_PD_VBUS) ? " pd_vb" : "", | |
2227 | (tmp & OTG_PU_VBUS) ? " pu_vb" : "", | |
2228 | (tmp & OTG_PU_ID) ? " pu_id" : "" | |
2229 | ); | |
2230 | tmp = OTG_IRQ_EN_REG; | |
2231 | seq_printf(s, "otg_irq_en %04x" "\n", tmp); | |
2232 | tmp = OTG_IRQ_SRC_REG; | |
2233 | seq_printf(s, "otg_irq_src %04x" "\n", tmp); | |
2234 | tmp = OTG_OUTCTRL_REG; | |
2235 | seq_printf(s, "otg_outctrl %04x" "\n", tmp); | |
2236 | tmp = OTG_TEST_REG; | |
2237 | seq_printf(s, "otg_test %04x" "\n", tmp); | |
2238 | } | |
2239 | ||
2240 | static int proc_udc_show(struct seq_file *s, void *_) | |
2241 | { | |
2242 | u32 tmp; | |
2243 | struct omap_ep *ep; | |
2244 | unsigned long flags; | |
2245 | ||
2246 | spin_lock_irqsave(&udc->lock, flags); | |
2247 | ||
2248 | seq_printf(s, "%s, version: " DRIVER_VERSION | |
2249 | #ifdef USE_ISO | |
2250 | " (iso)" | |
2251 | #endif | |
2252 | "%s\n", | |
2253 | driver_desc, | |
2254 | use_dma ? " (dma)" : ""); | |
2255 | ||
2256 | tmp = UDC_REV_REG & 0xff; | |
2257 | seq_printf(s, | |
2258 | "UDC rev %d.%d, fifo mode %d, gadget %s\n" | |
2259 | "hmc %d, transceiver %s\n", | |
2260 | tmp >> 4, tmp & 0xf, | |
2261 | fifo_mode, | |
2262 | udc->driver ? udc->driver->driver.name : "(none)", | |
2263 | HMC, | |
2264 | udc->transceiver ? udc->transceiver->label : "(none)"); | |
2265 | seq_printf(s, "ULPD control %04x req %04x status %04x\n", | |
2266 | __REG16(ULPD_CLOCK_CTRL), | |
2267 | __REG16(ULPD_SOFT_REQ), | |
2268 | __REG16(ULPD_STATUS_REQ)); | |
2269 | ||
2270 | /* OTG controller registers */ | |
2271 | if (!cpu_is_omap15xx()) | |
2272 | proc_otg_show(s); | |
2273 | ||
2274 | tmp = UDC_SYSCON1_REG; | |
2275 | seq_printf(s, "\nsyscon1 %04x" EIGHTBITS "\n", tmp, | |
2276 | (tmp & UDC_CFG_LOCK) ? " cfg_lock" : "", | |
2277 | (tmp & UDC_DATA_ENDIAN) ? " data_endian" : "", | |
2278 | (tmp & UDC_DMA_ENDIAN) ? " dma_endian" : "", | |
2279 | (tmp & UDC_NAK_EN) ? " nak" : "", | |
2280 | (tmp & UDC_AUTODECODE_DIS) ? " autodecode_dis" : "", | |
2281 | (tmp & UDC_SELF_PWR) ? " self_pwr" : "", | |
2282 | (tmp & UDC_SOFF_DIS) ? " soff_dis" : "", | |
2283 | (tmp & UDC_PULLUP_EN) ? " PULLUP" : ""); | |
2284 | // syscon2 is write-only | |
2285 | ||
2286 | /* UDC controller registers */ | |
2287 | if (!(tmp & UDC_PULLUP_EN)) { | |
2288 | seq_printf(s, "(suspended)\n"); | |
2289 | spin_unlock_irqrestore(&udc->lock, flags); | |
2290 | return 0; | |
2291 | } | |
2292 | ||
2293 | tmp = UDC_DEVSTAT_REG; | |
2294 | seq_printf(s, "devstat %04x" EIGHTBITS "%s%s\n", tmp, | |
2295 | (tmp & UDC_B_HNP_ENABLE) ? " b_hnp" : "", | |
2296 | (tmp & UDC_A_HNP_SUPPORT) ? " a_hnp" : "", | |
2297 | (tmp & UDC_A_ALT_HNP_SUPPORT) ? " a_alt_hnp" : "", | |
2298 | (tmp & UDC_R_WK_OK) ? " r_wk_ok" : "", | |
2299 | (tmp & UDC_USB_RESET) ? " usb_reset" : "", | |
2300 | (tmp & UDC_SUS) ? " SUS" : "", | |
2301 | (tmp & UDC_CFG) ? " CFG" : "", | |
2302 | (tmp & UDC_ADD) ? " ADD" : "", | |
2303 | (tmp & UDC_DEF) ? " DEF" : "", | |
2304 | (tmp & UDC_ATT) ? " ATT" : ""); | |
2305 | seq_printf(s, "sof %04x\n", UDC_SOF_REG); | |
2306 | tmp = UDC_IRQ_EN_REG; | |
2307 | seq_printf(s, "irq_en %04x" FOURBITS "%s\n", tmp, | |
2308 | (tmp & UDC_SOF_IE) ? " sof" : "", | |
2309 | (tmp & UDC_EPN_RX_IE) ? " epn_rx" : "", | |
2310 | (tmp & UDC_EPN_TX_IE) ? " epn_tx" : "", | |
2311 | (tmp & UDC_DS_CHG_IE) ? " ds_chg" : "", | |
2312 | (tmp & UDC_EP0_IE) ? " ep0" : ""); | |
2313 | tmp = UDC_IRQ_SRC_REG; | |
2314 | seq_printf(s, "irq_src %04x" EIGHTBITS "%s%s\n", tmp, | |
2315 | (tmp & UDC_TXN_DONE) ? " txn_done" : "", | |
2316 | (tmp & UDC_RXN_CNT) ? " rxn_cnt" : "", | |
2317 | (tmp & UDC_RXN_EOT) ? " rxn_eot" : "", | |
2318 | (tmp & UDC_SOF) ? " sof" : "", | |
2319 | (tmp & UDC_EPN_RX) ? " epn_rx" : "", | |
2320 | (tmp & UDC_EPN_TX) ? " epn_tx" : "", | |
2321 | (tmp & UDC_DS_CHG) ? " ds_chg" : "", | |
2322 | (tmp & UDC_SETUP) ? " setup" : "", | |
2323 | (tmp & UDC_EP0_RX) ? " ep0out" : "", | |
2324 | (tmp & UDC_EP0_TX) ? " ep0in" : ""); | |
2325 | if (use_dma) { | |
2326 | unsigned i; | |
2327 | ||
2328 | tmp = UDC_DMA_IRQ_EN_REG; | |
2329 | seq_printf(s, "dma_irq_en %04x%s" EIGHTBITS "\n", tmp, | |
2330 | (tmp & UDC_TX_DONE_IE(3)) ? " tx2_done" : "", | |
2331 | (tmp & UDC_RX_CNT_IE(3)) ? " rx2_cnt" : "", | |
2332 | (tmp & UDC_RX_EOT_IE(3)) ? " rx2_eot" : "", | |
2333 | ||
2334 | (tmp & UDC_TX_DONE_IE(2)) ? " tx1_done" : "", | |
2335 | (tmp & UDC_RX_CNT_IE(2)) ? " rx1_cnt" : "", | |
2336 | (tmp & UDC_RX_EOT_IE(2)) ? " rx1_eot" : "", | |
2337 | ||
2338 | (tmp & UDC_TX_DONE_IE(1)) ? " tx0_done" : "", | |
2339 | (tmp & UDC_RX_CNT_IE(1)) ? " rx0_cnt" : "", | |
2340 | (tmp & UDC_RX_EOT_IE(1)) ? " rx0_eot" : ""); | |
2341 | ||
2342 | tmp = UDC_RXDMA_CFG_REG; | |
2343 | seq_printf(s, "rxdma_cfg %04x\n", tmp); | |
2344 | if (tmp) { | |
2345 | for (i = 0; i < 3; i++) { | |
2346 | if ((tmp & (0x0f << (i * 4))) == 0) | |
2347 | continue; | |
2348 | seq_printf(s, "rxdma[%d] %04x\n", i, | |
2349 | UDC_RXDMA_REG(i + 1)); | |
2350 | } | |
2351 | } | |
2352 | tmp = UDC_TXDMA_CFG_REG; | |
2353 | seq_printf(s, "txdma_cfg %04x\n", tmp); | |
2354 | if (tmp) { | |
2355 | for (i = 0; i < 3; i++) { | |
2356 | if (!(tmp & (0x0f << (i * 4)))) | |
2357 | continue; | |
2358 | seq_printf(s, "txdma[%d] %04x\n", i, | |
2359 | UDC_TXDMA_REG(i + 1)); | |
2360 | } | |
2361 | } | |
2362 | } | |
2363 | ||
2364 | tmp = UDC_DEVSTAT_REG; | |
2365 | if (tmp & UDC_ATT) { | |
2366 | proc_ep_show(s, &udc->ep[0]); | |
2367 | if (tmp & UDC_ADD) { | |
2368 | list_for_each_entry (ep, &udc->gadget.ep_list, | |
2369 | ep.ep_list) { | |
2370 | if (ep->desc) | |
2371 | proc_ep_show(s, ep); | |
2372 | } | |
2373 | } | |
2374 | } | |
2375 | spin_unlock_irqrestore(&udc->lock, flags); | |
2376 | return 0; | |
2377 | } | |
2378 | ||
2379 | static int proc_udc_open(struct inode *inode, struct file *file) | |
2380 | { | |
2381 | return single_open(file, proc_udc_show, 0); | |
2382 | } | |
2383 | ||
2384 | static struct file_operations proc_ops = { | |
2385 | .open = proc_udc_open, | |
2386 | .read = seq_read, | |
2387 | .llseek = seq_lseek, | |
2388 | .release = single_release, | |
2389 | }; | |
2390 | ||
2391 | static void create_proc_file(void) | |
2392 | { | |
2393 | struct proc_dir_entry *pde; | |
2394 | ||
2395 | pde = create_proc_entry (proc_filename, 0, NULL); | |
2396 | if (pde) | |
2397 | pde->proc_fops = &proc_ops; | |
2398 | } | |
2399 | ||
2400 | static void remove_proc_file(void) | |
2401 | { | |
2402 | remove_proc_entry(proc_filename, 0); | |
2403 | } | |
2404 | ||
2405 | #else | |
2406 | ||
2407 | static inline void create_proc_file(void) {} | |
2408 | static inline void remove_proc_file(void) {} | |
2409 | ||
2410 | #endif | |
2411 | ||
2412 | /*-------------------------------------------------------------------------*/ | |
2413 | ||
2414 | /* Before this controller can enumerate, we need to pick an endpoint | |
2415 | * configuration, or "fifo_mode" That involves allocating 2KB of packet | |
2416 | * buffer space among the endpoints we'll be operating. | |
2417 | */ | |
2418 | static unsigned __init | |
2419 | omap_ep_setup(char *name, u8 addr, u8 type, | |
2420 | unsigned buf, unsigned maxp, int dbuf) | |
2421 | { | |
2422 | struct omap_ep *ep; | |
2423 | u16 epn_rxtx = 0; | |
2424 | ||
2425 | /* OUT endpoints first, then IN */ | |
2426 | ep = &udc->ep[addr & 0xf]; | |
2427 | if (addr & USB_DIR_IN) | |
2428 | ep += 16; | |
2429 | ||
2430 | /* in case of ep init table bugs */ | |
2431 | BUG_ON(ep->name[0]); | |
2432 | ||
2433 | /* chip setup ... bit values are same for IN, OUT */ | |
2434 | if (type == USB_ENDPOINT_XFER_ISOC) { | |
2435 | switch (maxp) { | |
2436 | case 8: epn_rxtx = 0 << 12; break; | |
2437 | case 16: epn_rxtx = 1 << 12; break; | |
2438 | case 32: epn_rxtx = 2 << 12; break; | |
2439 | case 64: epn_rxtx = 3 << 12; break; | |
2440 | case 128: epn_rxtx = 4 << 12; break; | |
2441 | case 256: epn_rxtx = 5 << 12; break; | |
2442 | case 512: epn_rxtx = 6 << 12; break; | |
2443 | default: BUG(); | |
2444 | } | |
2445 | epn_rxtx |= UDC_EPN_RX_ISO; | |
2446 | dbuf = 1; | |
2447 | } else { | |
2448 | /* double-buffering "not supported" on 15xx, | |
2449 | * and ignored for PIO-IN on 16xx | |
2450 | */ | |
2451 | if (!use_dma || cpu_is_omap15xx()) | |
2452 | dbuf = 0; | |
2453 | ||
2454 | switch (maxp) { | |
2455 | case 8: epn_rxtx = 0 << 12; break; | |
2456 | case 16: epn_rxtx = 1 << 12; break; | |
2457 | case 32: epn_rxtx = 2 << 12; break; | |
2458 | case 64: epn_rxtx = 3 << 12; break; | |
2459 | default: BUG(); | |
2460 | } | |
2461 | if (dbuf && addr) | |
2462 | epn_rxtx |= UDC_EPN_RX_DB; | |
2463 | init_timer(&ep->timer); | |
2464 | ep->timer.function = pio_out_timer; | |
2465 | ep->timer.data = (unsigned long) ep; | |
2466 | } | |
2467 | if (addr) | |
2468 | epn_rxtx |= UDC_EPN_RX_VALID; | |
2469 | BUG_ON(buf & 0x07); | |
2470 | epn_rxtx |= buf >> 3; | |
2471 | ||
2472 | DBG("%s addr %02x rxtx %04x maxp %d%s buf %d\n", | |
2473 | name, addr, epn_rxtx, maxp, dbuf ? "x2" : "", buf); | |
2474 | ||
2475 | if (addr & USB_DIR_IN) | |
2476 | UDC_EP_TX_REG(addr & 0xf) = epn_rxtx; | |
2477 | else | |
2478 | UDC_EP_RX_REG(addr) = epn_rxtx; | |
2479 | ||
2480 | /* next endpoint's buffer starts after this one's */ | |
2481 | buf += maxp; | |
2482 | if (dbuf) | |
2483 | buf += maxp; | |
2484 | BUG_ON(buf > 2048); | |
2485 | ||
2486 | /* set up driver data structures */ | |
2487 | BUG_ON(strlen(name) >= sizeof ep->name); | |
2488 | strlcpy(ep->name, name, sizeof ep->name); | |
2489 | INIT_LIST_HEAD(&ep->queue); | |
2490 | INIT_LIST_HEAD(&ep->iso); | |
2491 | ep->bEndpointAddress = addr; | |
2492 | ep->bmAttributes = type; | |
2493 | ep->double_buf = dbuf; | |
2494 | ep->udc = udc; | |
2495 | ||
2496 | ep->ep.name = ep->name; | |
2497 | ep->ep.ops = &omap_ep_ops; | |
2498 | ep->ep.maxpacket = ep->maxpacket = maxp; | |
2499 | list_add_tail (&ep->ep.ep_list, &udc->gadget.ep_list); | |
2500 | ||
2501 | return buf; | |
2502 | } | |
2503 | ||
2504 | static void omap_udc_release(struct device *dev) | |
2505 | { | |
2506 | complete(udc->done); | |
2507 | kfree (udc); | |
2508 | udc = 0; | |
2509 | } | |
2510 | ||
2511 | static int __init | |
2512 | omap_udc_setup(struct platform_device *odev, struct otg_transceiver *xceiv) | |
2513 | { | |
2514 | unsigned tmp, buf; | |
2515 | ||
2516 | /* abolish any previous hardware state */ | |
2517 | UDC_SYSCON1_REG = 0; | |
2518 | UDC_IRQ_EN_REG = 0; | |
2519 | UDC_IRQ_SRC_REG = UDC_IRQ_SRC_MASK; | |
2520 | UDC_DMA_IRQ_EN_REG = 0; | |
2521 | UDC_RXDMA_CFG_REG = 0; | |
2522 | UDC_TXDMA_CFG_REG = 0; | |
2523 | ||
2524 | /* UDC_PULLUP_EN gates the chip clock */ | |
2525 | // OTG_SYSCON_1_REG |= DEV_IDLE_EN; | |
2526 | ||
2527 | udc = kmalloc (sizeof *udc, SLAB_KERNEL); | |
2528 | if (!udc) | |
2529 | return -ENOMEM; | |
2530 | ||
2531 | memset(udc, 0, sizeof *udc); | |
2532 | spin_lock_init (&udc->lock); | |
2533 | ||
2534 | udc->gadget.ops = &omap_gadget_ops; | |
2535 | udc->gadget.ep0 = &udc->ep[0].ep; | |
2536 | INIT_LIST_HEAD(&udc->gadget.ep_list); | |
2537 | INIT_LIST_HEAD(&udc->iso); | |
2538 | udc->gadget.speed = USB_SPEED_UNKNOWN; | |
2539 | udc->gadget.name = driver_name; | |
2540 | ||
2541 | device_initialize(&udc->gadget.dev); | |
2542 | strcpy (udc->gadget.dev.bus_id, "gadget"); | |
2543 | udc->gadget.dev.release = omap_udc_release; | |
2544 | udc->gadget.dev.parent = &odev->dev; | |
2545 | if (use_dma) | |
2546 | udc->gadget.dev.dma_mask = odev->dev.dma_mask; | |
2547 | ||
2548 | udc->transceiver = xceiv; | |
2549 | ||
2550 | /* ep0 is special; put it right after the SETUP buffer */ | |
2551 | buf = omap_ep_setup("ep0", 0, USB_ENDPOINT_XFER_CONTROL, | |
2552 | 8 /* after SETUP */, 64 /* maxpacket */, 0); | |
2553 | list_del_init(&udc->ep[0].ep.ep_list); | |
2554 | ||
2555 | /* initially disable all non-ep0 endpoints */ | |
2556 | for (tmp = 1; tmp < 15; tmp++) { | |
2557 | UDC_EP_RX_REG(tmp) = 0; | |
2558 | UDC_EP_TX_REG(tmp) = 0; | |
2559 | } | |
2560 | ||
2561 | #define OMAP_BULK_EP(name,addr) \ | |
2562 | buf = omap_ep_setup(name "-bulk", addr, \ | |
2563 | USB_ENDPOINT_XFER_BULK, buf, 64, 1); | |
2564 | #define OMAP_INT_EP(name,addr, maxp) \ | |
2565 | buf = omap_ep_setup(name "-int", addr, \ | |
2566 | USB_ENDPOINT_XFER_INT, buf, maxp, 0); | |
2567 | #define OMAP_ISO_EP(name,addr, maxp) \ | |
2568 | buf = omap_ep_setup(name "-iso", addr, \ | |
2569 | USB_ENDPOINT_XFER_ISOC, buf, maxp, 1); | |
2570 | ||
2571 | switch (fifo_mode) { | |
2572 | case 0: | |
2573 | OMAP_BULK_EP("ep1in", USB_DIR_IN | 1); | |
2574 | OMAP_BULK_EP("ep2out", USB_DIR_OUT | 2); | |
2575 | OMAP_INT_EP("ep3in", USB_DIR_IN | 3, 16); | |
2576 | break; | |
2577 | case 1: | |
2578 | OMAP_BULK_EP("ep1in", USB_DIR_IN | 1); | |
2579 | OMAP_BULK_EP("ep2out", USB_DIR_OUT | 2); | |
2580 | OMAP_BULK_EP("ep3in", USB_DIR_IN | 3); | |
2581 | OMAP_BULK_EP("ep4out", USB_DIR_OUT | 4); | |
2582 | ||
2583 | OMAP_BULK_EP("ep5in", USB_DIR_IN | 5); | |
2584 | OMAP_BULK_EP("ep5out", USB_DIR_OUT | 5); | |
2585 | OMAP_BULK_EP("ep6in", USB_DIR_IN | 6); | |
2586 | OMAP_BULK_EP("ep6out", USB_DIR_OUT | 6); | |
2587 | ||
2588 | OMAP_BULK_EP("ep7in", USB_DIR_IN | 7); | |
2589 | OMAP_BULK_EP("ep7out", USB_DIR_OUT | 7); | |
2590 | OMAP_BULK_EP("ep8in", USB_DIR_IN | 8); | |
2591 | OMAP_BULK_EP("ep8out", USB_DIR_OUT | 8); | |
2592 | ||
2593 | OMAP_INT_EP("ep9in", USB_DIR_IN | 9, 16); | |
2594 | OMAP_INT_EP("ep10out", USB_DIR_IN | 10, 16); | |
2595 | OMAP_INT_EP("ep11in", USB_DIR_IN | 9, 16); | |
2596 | OMAP_INT_EP("ep12out", USB_DIR_IN | 10, 16); | |
2597 | break; | |
2598 | ||
2599 | #ifdef USE_ISO | |
2600 | case 2: /* mixed iso/bulk */ | |
2601 | OMAP_ISO_EP("ep1in", USB_DIR_IN | 1, 256); | |
2602 | OMAP_ISO_EP("ep2out", USB_DIR_OUT | 2, 256); | |
2603 | OMAP_ISO_EP("ep3in", USB_DIR_IN | 3, 128); | |
2604 | OMAP_ISO_EP("ep4out", USB_DIR_OUT | 4, 128); | |
2605 | ||
2606 | OMAP_INT_EP("ep5in", USB_DIR_IN | 5, 16); | |
2607 | ||
2608 | OMAP_BULK_EP("ep6in", USB_DIR_IN | 6); | |
2609 | OMAP_BULK_EP("ep7out", USB_DIR_OUT | 7); | |
2610 | OMAP_INT_EP("ep8in", USB_DIR_IN | 8, 16); | |
2611 | break; | |
2612 | case 3: /* mixed bulk/iso */ | |
2613 | OMAP_BULK_EP("ep1in", USB_DIR_IN | 1); | |
2614 | OMAP_BULK_EP("ep2out", USB_DIR_OUT | 2); | |
2615 | OMAP_INT_EP("ep3in", USB_DIR_IN | 3, 16); | |
2616 | ||
2617 | OMAP_BULK_EP("ep4in", USB_DIR_IN | 4); | |
2618 | OMAP_BULK_EP("ep5out", USB_DIR_OUT | 5); | |
2619 | OMAP_INT_EP("ep6in", USB_DIR_IN | 6, 16); | |
2620 | ||
2621 | OMAP_ISO_EP("ep7in", USB_DIR_IN | 7, 256); | |
2622 | OMAP_ISO_EP("ep8out", USB_DIR_OUT | 8, 256); | |
2623 | OMAP_INT_EP("ep9in", USB_DIR_IN | 9, 16); | |
2624 | break; | |
2625 | #endif | |
2626 | ||
2627 | /* add more modes as needed */ | |
2628 | ||
2629 | default: | |
2630 | ERR("unsupported fifo_mode #%d\n", fifo_mode); | |
2631 | return -ENODEV; | |
2632 | } | |
2633 | UDC_SYSCON1_REG = UDC_CFG_LOCK|UDC_SELF_PWR; | |
2634 | INFO("fifo mode %d, %d bytes not used\n", fifo_mode, 2048 - buf); | |
2635 | return 0; | |
2636 | } | |
2637 | ||
2638 | static int __init omap_udc_probe(struct device *dev) | |
2639 | { | |
2640 | struct platform_device *odev = to_platform_device(dev); | |
2641 | int status = -ENODEV; | |
2642 | int hmc; | |
2643 | struct otg_transceiver *xceiv = 0; | |
2644 | const char *type = 0; | |
2645 | struct omap_usb_config *config = dev->platform_data; | |
2646 | ||
2647 | /* NOTE: "knows" the order of the resources! */ | |
2648 | if (!request_mem_region(odev->resource[0].start, | |
2649 | odev->resource[0].end - odev->resource[0].start + 1, | |
2650 | driver_name)) { | |
2651 | DBG("request_mem_region failed\n"); | |
2652 | return -EBUSY; | |
2653 | } | |
2654 | ||
2655 | INFO("OMAP UDC rev %d.%d%s\n", | |
2656 | UDC_REV_REG >> 4, UDC_REV_REG & 0xf, | |
2657 | config->otg ? ", Mini-AB" : ""); | |
2658 | ||
2659 | /* use the mode given to us by board init code */ | |
2660 | if (cpu_is_omap15xx()) { | |
2661 | hmc = HMC_1510; | |
2662 | type = "(unknown)"; | |
2663 | ||
2664 | if (machine_is_omap_innovator()) { | |
2665 | /* just set up software VBUS detect, and then | |
2666 | * later rig it so we always report VBUS. | |
2667 | * FIXME without really sensing VBUS, we can't | |
2668 | * know when to turn PULLUP_EN on/off; and that | |
2669 | * means we always "need" the 48MHz clock. | |
2670 | */ | |
2671 | u32 tmp = FUNC_MUX_CTRL_0_REG; | |
2672 | ||
2673 | FUNC_MUX_CTRL_0_REG &= ~VBUS_CTRL_1510; | |
2674 | tmp |= VBUS_MODE_1510; | |
2675 | tmp &= ~VBUS_CTRL_1510; | |
2676 | FUNC_MUX_CTRL_0_REG = tmp; | |
2677 | } | |
2678 | } else { | |
2679 | hmc = HMC_1610; | |
2680 | switch (hmc) { | |
2681 | case 3: | |
2682 | case 11: | |
2683 | case 16: | |
2684 | case 19: | |
2685 | case 25: | |
2686 | xceiv = otg_get_transceiver(); | |
2687 | if (!xceiv) { | |
2688 | DBG("external transceiver not registered!\n"); | |
2689 | if (config->otg) | |
2690 | goto cleanup0; | |
2691 | type = "(unknown external)"; | |
2692 | } else | |
2693 | type = xceiv->label; | |
2694 | break; | |
2695 | case 0: /* POWERUP DEFAULT == 0 */ | |
2696 | case 4: | |
2697 | case 12: | |
2698 | case 20: | |
2699 | type = "INTEGRATED"; | |
2700 | break; | |
2701 | case 21: /* internal loopback */ | |
2702 | type = "(loopback)"; | |
2703 | break; | |
2704 | case 14: /* transceiverless */ | |
2705 | type = "(none)"; | |
2706 | break; | |
2707 | ||
2708 | default: | |
2709 | ERR("unrecognized UDC HMC mode %d\n", hmc); | |
2710 | return -ENODEV; | |
2711 | } | |
2712 | } | |
2713 | INFO("hmc mode %d, transceiver %s\n", hmc, type); | |
2714 | ||
2715 | /* a "gadget" abstracts/virtualizes the controller */ | |
2716 | status = omap_udc_setup(odev, xceiv); | |
2717 | if (status) { | |
2718 | goto cleanup0; | |
2719 | } | |
2720 | xceiv = 0; | |
2721 | // "udc" is now valid | |
2722 | pullup_disable(udc); | |
2723 | #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) | |
2724 | udc->gadget.is_otg = (config->otg != 0); | |
2725 | #endif | |
2726 | ||
2727 | /* USB general purpose IRQ: ep0, state changes, dma, etc */ | |
2728 | status = request_irq(odev->resource[1].start, omap_udc_irq, | |
2729 | SA_SAMPLE_RANDOM, driver_name, udc); | |
2730 | if (status != 0) { | |
2731 | ERR( "can't get irq %ld, err %d\n", | |
2732 | odev->resource[1].start, status); | |
2733 | goto cleanup1; | |
2734 | } | |
2735 | ||
2736 | /* USB "non-iso" IRQ (PIO for all but ep0) */ | |
2737 | status = request_irq(odev->resource[2].start, omap_udc_pio_irq, | |
2738 | SA_SAMPLE_RANDOM, "omap_udc pio", udc); | |
2739 | if (status != 0) { | |
2740 | ERR( "can't get irq %ld, err %d\n", | |
2741 | odev->resource[2].start, status); | |
2742 | goto cleanup2; | |
2743 | } | |
2744 | #ifdef USE_ISO | |
2745 | status = request_irq(odev->resource[3].start, omap_udc_iso_irq, | |
2746 | SA_INTERRUPT, "omap_udc iso", udc); | |
2747 | if (status != 0) { | |
2748 | ERR("can't get irq %ld, err %d\n", | |
2749 | odev->resource[3].start, status); | |
2750 | goto cleanup3; | |
2751 | } | |
2752 | #endif | |
2753 | ||
2754 | create_proc_file(); | |
2755 | device_add(&udc->gadget.dev); | |
2756 | return 0; | |
2757 | ||
2758 | #ifdef USE_ISO | |
2759 | cleanup3: | |
2760 | free_irq(odev->resource[2].start, udc); | |
2761 | #endif | |
2762 | ||
2763 | cleanup2: | |
2764 | free_irq(odev->resource[1].start, udc); | |
2765 | ||
2766 | cleanup1: | |
2767 | kfree (udc); | |
2768 | udc = 0; | |
2769 | ||
2770 | cleanup0: | |
2771 | if (xceiv) | |
2772 | put_device(xceiv->dev); | |
2773 | release_mem_region(odev->resource[0].start, | |
2774 | odev->resource[0].end - odev->resource[0].start + 1); | |
2775 | return status; | |
2776 | } | |
2777 | ||
2778 | static int __exit omap_udc_remove(struct device *dev) | |
2779 | { | |
2780 | struct platform_device *odev = to_platform_device(dev); | |
2781 | DECLARE_COMPLETION(done); | |
2782 | ||
2783 | if (!udc) | |
2784 | return -ENODEV; | |
2785 | ||
2786 | udc->done = &done; | |
2787 | ||
2788 | pullup_disable(udc); | |
2789 | if (udc->transceiver) { | |
2790 | put_device(udc->transceiver->dev); | |
2791 | udc->transceiver = 0; | |
2792 | } | |
2793 | UDC_SYSCON1_REG = 0; | |
2794 | ||
2795 | remove_proc_file(); | |
2796 | ||
2797 | #ifdef USE_ISO | |
2798 | free_irq(odev->resource[3].start, udc); | |
2799 | #endif | |
2800 | free_irq(odev->resource[2].start, udc); | |
2801 | free_irq(odev->resource[1].start, udc); | |
2802 | ||
2803 | release_mem_region(odev->resource[0].start, | |
2804 | odev->resource[0].end - odev->resource[0].start + 1); | |
2805 | ||
2806 | device_unregister(&udc->gadget.dev); | |
2807 | wait_for_completion(&done); | |
2808 | ||
2809 | return 0; | |
2810 | } | |
2811 | ||
2812 | /* suspend/resume/wakeup from sysfs (echo > power/state) */ | |
2813 | ||
2814 | static int omap_udc_suspend(struct device *dev, u32 state, u32 level) | |
2815 | { | |
2816 | if (level != 0) | |
2817 | return 0; | |
2818 | ||
2819 | DBG("suspend, state %d\n", state); | |
2820 | omap_pullup(&udc->gadget, 0); | |
2821 | udc->gadget.dev.power.power_state = 3; | |
2822 | udc->gadget.dev.parent->power.power_state = 3; | |
2823 | return 0; | |
2824 | } | |
2825 | ||
2826 | static int omap_udc_resume(struct device *dev, u32 level) | |
2827 | { | |
2828 | if (level != 0) | |
2829 | return 0; | |
2830 | ||
2831 | DBG("resume + wakeup/SRP\n"); | |
2832 | udc->gadget.dev.parent->power.power_state = 0; | |
2833 | udc->gadget.dev.power.power_state = 0; | |
2834 | omap_pullup(&udc->gadget, 1); | |
2835 | ||
2836 | /* maybe the host would enumerate us if we nudged it */ | |
2837 | msleep(100); | |
2838 | return omap_wakeup(&udc->gadget); | |
2839 | } | |
2840 | ||
2841 | /*-------------------------------------------------------------------------*/ | |
2842 | ||
2843 | static struct device_driver udc_driver = { | |
2844 | .name = (char *) driver_name, | |
2845 | .bus = &platform_bus_type, | |
2846 | .probe = omap_udc_probe, | |
2847 | .remove = __exit_p(omap_udc_remove), | |
2848 | .suspend = omap_udc_suspend, | |
2849 | .resume = omap_udc_resume, | |
2850 | }; | |
2851 | ||
2852 | static int __init udc_init(void) | |
2853 | { | |
2854 | INFO("%s, version: " DRIVER_VERSION | |
2855 | #ifdef USE_ISO | |
2856 | " (iso)" | |
2857 | #endif | |
2858 | "%s\n", driver_desc, | |
2859 | use_dma ? " (dma)" : ""); | |
2860 | return driver_register(&udc_driver); | |
2861 | } | |
2862 | module_init(udc_init); | |
2863 | ||
2864 | static void __exit udc_exit(void) | |
2865 | { | |
2866 | driver_unregister(&udc_driver); | |
2867 | } | |
2868 | module_exit(udc_exit); | |
2869 | ||
2870 | MODULE_DESCRIPTION(DRIVER_DESC); | |
2871 | MODULE_LICENSE("GPL"); | |
2872 |