Commit | Line | Data |
---|---|---|
80cb9aee RV |
1 | /* |
2 | * (C) Copyright David Brownell 2000-2002 | |
3 | * Copyright (c) 2005 MontaVista Software | |
4 | * | |
5 | * This program is free software; you can redistribute it and/or modify it | |
6 | * under the terms of the GNU General Public License as published by the | |
7 | * Free Software Foundation; either version 2 of the License, or (at your | |
8 | * option) any later version. | |
9 | * | |
10 | * This program is distributed in the hope that it will be useful, but | |
11 | * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY | |
12 | * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License | |
13 | * for more details. | |
14 | * | |
15 | * You should have received a copy of the GNU General Public License | |
16 | * along with this program; if not, write to the Free Software Foundation, | |
17 | * Inc., 675 Mass Ave, Cambridge, MA 02139, USA. | |
18 | * | |
19 | * Ported to 834x by Randy Vinson <rvinson@mvista.com> using code provided | |
20 | * by Hunter Wu. | |
21 | */ | |
22 | ||
23 | #include <linux/platform_device.h> | |
24 | #include <linux/fsl_devices.h> | |
25 | ||
26 | #include "ehci-fsl.h" | |
27 | ||
28 | /* FIXME: Power Managment is un-ported so temporarily disable it */ | |
29 | #undef CONFIG_PM | |
30 | ||
31 | /* PCI-based HCs are common, but plenty of non-PCI HCs are used too */ | |
32 | ||
33 | /* configure so an HC device and id are always provided */ | |
34 | /* always called with process context; sleeping is OK */ | |
35 | ||
36 | /** | |
37 | * usb_hcd_fsl_probe - initialize FSL-based HCDs | |
38 | * @drvier: Driver to be used for this HCD | |
39 | * @pdev: USB Host Controller being probed | |
40 | * Context: !in_interrupt() | |
41 | * | |
42 | * Allocates basic resources for this USB host controller. | |
43 | * | |
44 | */ | |
45 | int usb_hcd_fsl_probe(const struct hc_driver *driver, | |
46 | struct platform_device *pdev) | |
47 | { | |
48 | struct fsl_usb2_platform_data *pdata; | |
49 | struct usb_hcd *hcd; | |
50 | struct resource *res; | |
51 | int irq; | |
52 | int retval; | |
53 | unsigned int temp; | |
54 | ||
55 | pr_debug("initializing FSL-SOC USB Controller\n"); | |
56 | ||
57 | /* Need platform data for setup */ | |
58 | pdata = (struct fsl_usb2_platform_data *)pdev->dev.platform_data; | |
59 | if (!pdata) { | |
60 | dev_err(&pdev->dev, | |
61 | "No platform data for %s.\n", pdev->dev.bus_id); | |
62 | return -ENODEV; | |
63 | } | |
64 | ||
65 | /* | |
66 | * This is a host mode driver, verify that we're supposed to be | |
67 | * in host mode. | |
68 | */ | |
69 | if (!((pdata->operating_mode == FSL_USB2_DR_HOST) || | |
70 | (pdata->operating_mode == FSL_USB2_MPH_HOST))) { | |
71 | dev_err(&pdev->dev, | |
72 | "Non Host Mode configured for %s. Wrong driver linked.\n", | |
73 | pdev->dev.bus_id); | |
74 | return -ENODEV; | |
75 | } | |
76 | ||
77 | res = platform_get_resource(pdev, IORESOURCE_IRQ, 0); | |
78 | if (!res) { | |
79 | dev_err(&pdev->dev, | |
80 | "Found HC with no IRQ. Check %s setup!\n", | |
81 | pdev->dev.bus_id); | |
82 | return -ENODEV; | |
83 | } | |
84 | irq = res->start; | |
85 | ||
86 | hcd = usb_create_hcd(driver, &pdev->dev, pdev->dev.bus_id); | |
87 | if (!hcd) { | |
88 | retval = -ENOMEM; | |
89 | goto err1; | |
90 | } | |
91 | ||
92 | res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
93 | if (!res) { | |
94 | dev_err(&pdev->dev, | |
95 | "Found HC with no register addr. Check %s setup!\n", | |
96 | pdev->dev.bus_id); | |
97 | retval = -ENODEV; | |
98 | goto err2; | |
99 | } | |
100 | hcd->rsrc_start = res->start; | |
101 | hcd->rsrc_len = res->end - res->start + 1; | |
102 | if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, | |
103 | driver->description)) { | |
104 | dev_dbg(&pdev->dev, "controller already in use\n"); | |
105 | retval = -EBUSY; | |
106 | goto err2; | |
107 | } | |
108 | hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); | |
109 | ||
110 | if (hcd->regs == NULL) { | |
111 | dev_dbg(&pdev->dev, "error mapping memory\n"); | |
112 | retval = -EFAULT; | |
113 | goto err3; | |
114 | } | |
115 | ||
116 | /* Enable USB controller */ | |
117 | temp = in_be32(hcd->regs + 0x500); | |
118 | out_be32(hcd->regs + 0x500, temp | 0x4); | |
119 | ||
120 | /* Set to Host mode */ | |
121 | temp = in_le32(hcd->regs + 0x1a8); | |
122 | out_le32(hcd->regs + 0x1a8, temp | 0x3); | |
123 | ||
d54b5caa | 124 | retval = usb_add_hcd(hcd, irq, IRQF_SHARED); |
80cb9aee RV |
125 | if (retval != 0) |
126 | goto err4; | |
127 | return retval; | |
128 | ||
129 | err4: | |
130 | iounmap(hcd->regs); | |
131 | err3: | |
132 | release_mem_region(hcd->rsrc_start, hcd->rsrc_len); | |
133 | err2: | |
134 | usb_put_hcd(hcd); | |
135 | err1: | |
136 | dev_err(&pdev->dev, "init %s fail, %d\n", pdev->dev.bus_id, retval); | |
137 | return retval; | |
138 | } | |
139 | ||
140 | /* may be called without controller electrically present */ | |
141 | /* may be called with controller, bus, and devices active */ | |
142 | ||
143 | /** | |
144 | * usb_hcd_fsl_remove - shutdown processing for FSL-based HCDs | |
145 | * @dev: USB Host Controller being removed | |
146 | * Context: !in_interrupt() | |
147 | * | |
148 | * Reverses the effect of usb_hcd_fsl_probe(). | |
149 | * | |
150 | */ | |
151 | void usb_hcd_fsl_remove(struct usb_hcd *hcd, struct platform_device *pdev) | |
152 | { | |
153 | usb_remove_hcd(hcd); | |
154 | iounmap(hcd->regs); | |
155 | release_mem_region(hcd->rsrc_start, hcd->rsrc_len); | |
156 | usb_put_hcd(hcd); | |
157 | } | |
158 | ||
159 | static void mpc83xx_setup_phy(struct ehci_hcd *ehci, | |
160 | enum fsl_usb2_phy_modes phy_mode, | |
161 | unsigned int port_offset) | |
162 | { | |
499003e8 | 163 | u32 portsc = 0; |
80cb9aee RV |
164 | switch (phy_mode) { |
165 | case FSL_USB2_PHY_ULPI: | |
166 | portsc |= PORT_PTS_ULPI; | |
167 | break; | |
168 | case FSL_USB2_PHY_SERIAL: | |
169 | portsc |= PORT_PTS_SERIAL; | |
170 | break; | |
171 | case FSL_USB2_PHY_UTMI_WIDE: | |
172 | portsc |= PORT_PTS_PTW; | |
173 | /* fall through */ | |
174 | case FSL_USB2_PHY_UTMI: | |
175 | portsc |= PORT_PTS_UTMI; | |
176 | break; | |
177 | case FSL_USB2_PHY_NONE: | |
178 | break; | |
179 | } | |
180 | writel(portsc, &ehci->regs->port_status[port_offset]); | |
181 | } | |
182 | ||
183 | static void mpc83xx_usb_setup(struct usb_hcd *hcd) | |
184 | { | |
185 | struct ehci_hcd *ehci = hcd_to_ehci(hcd); | |
186 | struct fsl_usb2_platform_data *pdata; | |
187 | void __iomem *non_ehci = hcd->regs; | |
188 | ||
189 | pdata = | |
190 | (struct fsl_usb2_platform_data *)hcd->self.controller-> | |
191 | platform_data; | |
192 | /* Enable PHY interface in the control reg. */ | |
193 | out_be32(non_ehci + FSL_SOC_USB_CTRL, 0x00000004); | |
194 | out_be32(non_ehci + FSL_SOC_USB_SNOOP1, 0x0000001b); | |
195 | ||
196 | if (pdata->operating_mode == FSL_USB2_DR_HOST) | |
197 | mpc83xx_setup_phy(ehci, pdata->phy_mode, 0); | |
198 | ||
199 | if (pdata->operating_mode == FSL_USB2_MPH_HOST) { | |
8cd42e97 KG |
200 | unsigned int chip, rev, svr; |
201 | ||
202 | svr = mfspr(SPRN_SVR); | |
203 | chip = svr >> 16; | |
204 | rev = (svr >> 4) & 0xf; | |
205 | ||
206 | /* Deal with USB Erratum #14 on MPC834x Rev 1.0 & 1.1 chips */ | |
207 | if ((rev == 1) && (chip >= 0x8050) && (chip <= 0x8055)) | |
208 | ehci->has_fsl_port_bug = 1; | |
209 | ||
80cb9aee RV |
210 | if (pdata->port_enables & FSL_USB2_PORT0_ENABLED) |
211 | mpc83xx_setup_phy(ehci, pdata->phy_mode, 0); | |
212 | if (pdata->port_enables & FSL_USB2_PORT1_ENABLED) | |
213 | mpc83xx_setup_phy(ehci, pdata->phy_mode, 1); | |
214 | } | |
215 | ||
216 | /* put controller in host mode. */ | |
217 | writel(0x00000003, non_ehci + FSL_SOC_USB_USBMODE); | |
218 | out_be32(non_ehci + FSL_SOC_USB_PRICTRL, 0x0000000c); | |
219 | out_be32(non_ehci + FSL_SOC_USB_AGECNTTHRSH, 0x00000040); | |
220 | out_be32(non_ehci + FSL_SOC_USB_SICTRL, 0x00000001); | |
221 | } | |
222 | ||
223 | /* called after powerup, by probe or system-pm "wakeup" */ | |
224 | static int ehci_fsl_reinit(struct ehci_hcd *ehci) | |
225 | { | |
226 | mpc83xx_usb_setup(ehci_to_hcd(ehci)); | |
227 | ehci_port_power(ehci, 0); | |
228 | ||
229 | return 0; | |
230 | } | |
231 | ||
232 | /* called during probe() after chip reset completes */ | |
233 | static int ehci_fsl_setup(struct usb_hcd *hcd) | |
234 | { | |
235 | struct ehci_hcd *ehci = hcd_to_ehci(hcd); | |
236 | int retval; | |
237 | ||
238 | /* EHCI registers start at offset 0x100 */ | |
239 | ehci->caps = hcd->regs + 0x100; | |
240 | ehci->regs = hcd->regs + 0x100 + | |
241 | HC_LENGTH(readl(&ehci->caps->hc_capbase)); | |
242 | dbg_hcs_params(ehci, "reset"); | |
243 | dbg_hcc_params(ehci, "reset"); | |
244 | ||
245 | /* cache this readonly data; minimize chip reads */ | |
246 | ehci->hcs_params = readl(&ehci->caps->hcs_params); | |
247 | ||
248 | retval = ehci_halt(ehci); | |
249 | if (retval) | |
250 | return retval; | |
251 | ||
252 | /* data structure init */ | |
253 | retval = ehci_init(hcd); | |
254 | if (retval) | |
255 | return retval; | |
256 | ||
257 | ehci->is_tdi_rh_tt = 1; | |
258 | ||
259 | ehci->sbrn = 0x20; | |
260 | ||
261 | ehci_reset(ehci); | |
262 | ||
263 | retval = ehci_fsl_reinit(ehci); | |
264 | return retval; | |
265 | } | |
266 | ||
267 | static const struct hc_driver ehci_fsl_hc_driver = { | |
268 | .description = hcd_name, | |
269 | .product_desc = "Freescale On-Chip EHCI Host Controller", | |
270 | .hcd_priv_size = sizeof(struct ehci_hcd), | |
271 | ||
272 | /* | |
273 | * generic hardware linkage | |
274 | */ | |
275 | .irq = ehci_irq, | |
276 | .flags = HCD_USB2, | |
277 | ||
278 | /* | |
279 | * basic lifecycle operations | |
280 | */ | |
281 | .reset = ehci_fsl_setup, | |
282 | .start = ehci_run, | |
283 | #ifdef CONFIG_PM | |
284 | .suspend = ehci_bus_suspend, | |
285 | .resume = ehci_bus_resume, | |
286 | #endif | |
287 | .stop = ehci_stop, | |
64a21d02 | 288 | .shutdown = ehci_shutdown, |
80cb9aee RV |
289 | |
290 | /* | |
291 | * managing i/o requests and associated device resources | |
292 | */ | |
293 | .urb_enqueue = ehci_urb_enqueue, | |
294 | .urb_dequeue = ehci_urb_dequeue, | |
295 | .endpoint_disable = ehci_endpoint_disable, | |
296 | ||
297 | /* | |
298 | * scheduling support | |
299 | */ | |
300 | .get_frame_number = ehci_get_frame, | |
301 | ||
302 | /* | |
303 | * root hub support | |
304 | */ | |
305 | .hub_status_data = ehci_hub_status_data, | |
306 | .hub_control = ehci_hub_control, | |
307 | .bus_suspend = ehci_bus_suspend, | |
308 | .bus_resume = ehci_bus_resume, | |
309 | }; | |
310 | ||
311 | static int ehci_fsl_drv_probe(struct platform_device *pdev) | |
312 | { | |
313 | if (usb_disabled()) | |
314 | return -ENODEV; | |
315 | ||
316 | return usb_hcd_fsl_probe(&ehci_fsl_hc_driver, pdev); | |
317 | } | |
318 | ||
319 | static int ehci_fsl_drv_remove(struct platform_device *pdev) | |
320 | { | |
321 | struct usb_hcd *hcd = platform_get_drvdata(pdev); | |
322 | ||
323 | usb_hcd_fsl_remove(hcd, pdev); | |
324 | ||
325 | return 0; | |
326 | } | |
327 | ||
01cced25 | 328 | MODULE_ALIAS("fsl-ehci"); |
80cb9aee | 329 | |
01cced25 | 330 | static struct platform_driver ehci_fsl_driver = { |
80cb9aee RV |
331 | .probe = ehci_fsl_drv_probe, |
332 | .remove = ehci_fsl_drv_remove, | |
64a21d02 | 333 | .shutdown = usb_hcd_platform_shutdown, |
80cb9aee | 334 | .driver = { |
01cced25 | 335 | .name = "fsl-ehci", |
80cb9aee RV |
336 | }, |
337 | }; |