Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * OHCI HCD (Host Controller Driver) for USB. | |
3 | * | |
4 | * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at> | |
5 | * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net> | |
6 | * | |
7 | * [ Initialisation is based on Linus' ] | |
8 | * [ uhci code and gregs ohci fragments ] | |
9 | * [ (C) Copyright 1999 Linus Torvalds ] | |
10 | * [ (C) Copyright 1999 Gregory P. Smith] | |
11 | * | |
12 | * PCI Bus Glue | |
13 | * | |
14 | * This file is licenced under the GPL. | |
15 | */ | |
16 | ||
1da177e4 LT |
17 | #ifndef CONFIG_PCI |
18 | #error "This file is PCI bus glue. CONFIG_PCI must be defined." | |
19 | #endif | |
20 | ||
21 | /*-------------------------------------------------------------------------*/ | |
22 | ||
23 | static int | |
24 | ohci_pci_reset (struct usb_hcd *hcd) | |
25 | { | |
26 | struct ohci_hcd *ohci = hcd_to_ohci (hcd); | |
27 | ||
28 | ohci_hcd_init (ohci); | |
29 | return ohci_init (ohci); | |
30 | } | |
31 | ||
32 | static int __devinit | |
33 | ohci_pci_start (struct usb_hcd *hcd) | |
34 | { | |
35 | struct ohci_hcd *ohci = hcd_to_ohci (hcd); | |
36 | int ret; | |
37 | ||
6a9062f3 DB |
38 | /* REVISIT this whole block should move to reset(), which handles |
39 | * all the other one-time init. | |
40 | */ | |
41 | if (hcd->self.controller) { | |
1da177e4 LT |
42 | struct pci_dev *pdev = to_pci_dev(hcd->self.controller); |
43 | ||
44 | /* AMD 756, for most chips (early revs), corrupts register | |
45 | * values on read ... so enable the vendor workaround. | |
46 | */ | |
47 | if (pdev->vendor == PCI_VENDOR_ID_AMD | |
48 | && pdev->device == 0x740c) { | |
49 | ohci->flags = OHCI_QUIRK_AMD756; | |
0e498763 | 50 | ohci_dbg (ohci, "AMD756 erratum 4 workaround\n"); |
6a9062f3 DB |
51 | /* also erratum 10 (suspend/resume issues) */ |
52 | device_init_wakeup(&hcd->self.root_hub->dev, 0); | |
1da177e4 LT |
53 | } |
54 | ||
55 | /* FIXME for some of the early AMD 760 southbridges, OHCI | |
56 | * won't work at all. blacklist them. | |
57 | */ | |
58 | ||
59 | /* Apple's OHCI driver has a lot of bizarre workarounds | |
60 | * for this chip. Evidently control and bulk lists | |
61 | * can get confused. (B&W G3 models, and ...) | |
62 | */ | |
63 | else if (pdev->vendor == PCI_VENDOR_ID_OPTI | |
64 | && pdev->device == 0xc861) { | |
0e498763 | 65 | ohci_dbg (ohci, |
1da177e4 LT |
66 | "WARNING: OPTi workarounds unavailable\n"); |
67 | } | |
68 | ||
69 | /* Check for NSC87560. We have to look at the bridge (fn1) to | |
70 | * identify the USB (fn2). This quirk might apply to more or | |
71 | * even all NSC stuff. | |
72 | */ | |
73 | else if (pdev->vendor == PCI_VENDOR_ID_NS) { | |
74 | struct pci_dev *b; | |
75 | ||
76 | b = pci_find_slot (pdev->bus->number, | |
77 | PCI_DEVFN (PCI_SLOT (pdev->devfn), 1)); | |
78 | if (b && b->device == PCI_DEVICE_ID_NS_87560_LIO | |
79 | && b->vendor == PCI_VENDOR_ID_NS) { | |
80 | ohci->flags |= OHCI_QUIRK_SUPERIO; | |
0e498763 | 81 | ohci_dbg (ohci, "Using NSC SuperIO setup\n"); |
1da177e4 LT |
82 | } |
83 | } | |
0e498763 DB |
84 | |
85 | /* Check for Compaq's ZFMicro chipset, which needs short | |
86 | * delays before control or bulk queues get re-activated | |
87 | * in finish_unlinks() | |
88 | */ | |
89 | else if (pdev->vendor == PCI_VENDOR_ID_COMPAQ | |
90 | && pdev->device == 0xa0f8) { | |
91 | ohci->flags |= OHCI_QUIRK_ZFMICRO; | |
92 | ohci_dbg (ohci, | |
93 | "enabled Compaq ZFMicro chipset quirk\n"); | |
94 | } | |
6a9062f3 DB |
95 | |
96 | /* RWC may not be set for add-in PCI cards, since boot | |
97 | * firmware probably ignored them. This transfers PCI | |
98 | * PM wakeup capabilities (once the PCI layer is fixed). | |
99 | */ | |
100 | if (device_may_wakeup(&pdev->dev)) | |
101 | ohci->hc_control |= OHCI_CTRL_RWC; | |
1da177e4 LT |
102 | } |
103 | ||
104 | /* NOTE: there may have already been a first reset, to | |
105 | * keep bios/smm irqs from making trouble | |
106 | */ | |
107 | if ((ret = ohci_run (ohci)) < 0) { | |
108 | ohci_err (ohci, "can't start\n"); | |
109 | ohci_stop (hcd); | |
110 | return ret; | |
111 | } | |
112 | return 0; | |
113 | } | |
114 | ||
115 | #ifdef CONFIG_PM | |
116 | ||
9a5d3e98 | 117 | static int ohci_pci_suspend (struct usb_hcd *hcd, pm_message_t message) |
1da177e4 | 118 | { |
8de98402 BH |
119 | struct ohci_hcd *ohci = hcd_to_ohci (hcd); |
120 | unsigned long flags; | |
121 | int rc = 0; | |
122 | ||
123 | /* Root hub was already suspended. Disable irq emission and | |
124 | * mark HW unaccessible, bail out if RH has been resumed. Use | |
125 | * the spinlock to properly synchronize with possible pending | |
126 | * RH suspend or resume activity. | |
127 | * | |
128 | * This is still racy as hcd->state is manipulated outside of | |
129 | * any locks =P But that will be a different fix. | |
130 | */ | |
131 | spin_lock_irqsave (&ohci->lock, flags); | |
132 | if (hcd->state != HC_STATE_SUSPENDED) { | |
133 | rc = -EINVAL; | |
134 | goto bail; | |
135 | } | |
136 | ohci_writel(ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable); | |
137 | (void)ohci_readl(ohci, &ohci->regs->intrdisable); | |
18584999 DB |
138 | |
139 | /* make sure snapshot being resumed re-enumerates everything */ | |
140 | if (message.event == PM_EVENT_PRETHAW) | |
141 | ohci_usb_reset(ohci); | |
142 | ||
8de98402 BH |
143 | clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); |
144 | bail: | |
145 | spin_unlock_irqrestore (&ohci->lock, flags); | |
146 | ||
147 | return rc; | |
1da177e4 LT |
148 | } |
149 | ||
150 | ||
151 | static int ohci_pci_resume (struct usb_hcd *hcd) | |
152 | { | |
8de98402 | 153 | set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); |
f197b2c5 DB |
154 | usb_hcd_resume_root_hub(hcd); |
155 | return 0; | |
1da177e4 LT |
156 | } |
157 | ||
158 | #endif /* CONFIG_PM */ | |
159 | ||
160 | ||
161 | /*-------------------------------------------------------------------------*/ | |
162 | ||
163 | static const struct hc_driver ohci_pci_hc_driver = { | |
164 | .description = hcd_name, | |
165 | .product_desc = "OHCI Host Controller", | |
166 | .hcd_priv_size = sizeof(struct ohci_hcd), | |
167 | ||
168 | /* | |
169 | * generic hardware linkage | |
170 | */ | |
171 | .irq = ohci_irq, | |
172 | .flags = HCD_MEMORY | HCD_USB11, | |
173 | ||
174 | /* | |
175 | * basic lifecycle operations | |
176 | */ | |
177 | .reset = ohci_pci_reset, | |
178 | .start = ohci_pci_start, | |
d413984a | 179 | .stop = ohci_stop, |
64a21d02 | 180 | .shutdown = ohci_shutdown, |
d413984a | 181 | |
1da177e4 | 182 | #ifdef CONFIG_PM |
d413984a | 183 | /* these suspend/resume entries are for upstream PCI glue ONLY */ |
1da177e4 LT |
184 | .suspend = ohci_pci_suspend, |
185 | .resume = ohci_pci_resume, | |
186 | #endif | |
1da177e4 LT |
187 | |
188 | /* | |
189 | * managing i/o requests and associated device resources | |
190 | */ | |
191 | .urb_enqueue = ohci_urb_enqueue, | |
192 | .urb_dequeue = ohci_urb_dequeue, | |
193 | .endpoint_disable = ohci_endpoint_disable, | |
194 | ||
195 | /* | |
196 | * scheduling support | |
197 | */ | |
198 | .get_frame_number = ohci_get_frame, | |
199 | ||
200 | /* | |
201 | * root hub support | |
202 | */ | |
203 | .hub_status_data = ohci_hub_status_data, | |
204 | .hub_control = ohci_hub_control, | |
d413984a | 205 | .hub_irq_enable = ohci_rhsc_enable, |
8ad7fe16 | 206 | #ifdef CONFIG_PM |
0c0382e3 AS |
207 | .bus_suspend = ohci_bus_suspend, |
208 | .bus_resume = ohci_bus_resume, | |
1da177e4 LT |
209 | #endif |
210 | .start_port_reset = ohci_start_port_reset, | |
211 | }; | |
212 | ||
213 | /*-------------------------------------------------------------------------*/ | |
214 | ||
215 | ||
216 | static const struct pci_device_id pci_ids [] = { { | |
217 | /* handle any USB OHCI controller */ | |
c67808ee | 218 | PCI_DEVICE_CLASS(PCI_CLASS_SERIAL_USB_OHCI, ~0), |
1da177e4 LT |
219 | .driver_data = (unsigned long) &ohci_pci_hc_driver, |
220 | }, { /* end: all zeroes */ } | |
221 | }; | |
222 | MODULE_DEVICE_TABLE (pci, pci_ids); | |
223 | ||
224 | /* pci driver glue; this is a "new style" PCI driver module */ | |
225 | static struct pci_driver ohci_pci_driver = { | |
226 | .name = (char *) hcd_name, | |
227 | .id_table = pci_ids, | |
228 | ||
229 | .probe = usb_hcd_pci_probe, | |
230 | .remove = usb_hcd_pci_remove, | |
231 | ||
232 | #ifdef CONFIG_PM | |
233 | .suspend = usb_hcd_pci_suspend, | |
234 | .resume = usb_hcd_pci_resume, | |
235 | #endif | |
64a21d02 AG |
236 | |
237 | .shutdown = usb_hcd_pci_shutdown, | |
1da177e4 LT |
238 | }; |
239 | ||
240 | ||
241 | static int __init ohci_hcd_pci_init (void) | |
242 | { | |
243 | printk (KERN_DEBUG "%s: " DRIVER_INFO " (PCI)\n", hcd_name); | |
244 | if (usb_disabled()) | |
245 | return -ENODEV; | |
246 | ||
247 | pr_debug ("%s: block sizes: ed %Zd td %Zd\n", hcd_name, | |
248 | sizeof (struct ed), sizeof (struct td)); | |
249 | return pci_register_driver (&ohci_pci_driver); | |
250 | } | |
251 | module_init (ohci_hcd_pci_init); | |
252 | ||
253 | /*-------------------------------------------------------------------------*/ | |
254 | ||
255 | static void __exit ohci_hcd_pci_cleanup (void) | |
256 | { | |
257 | pci_unregister_driver (&ohci_pci_driver); | |
258 | } | |
259 | module_exit (ohci_hcd_pci_cleanup); |