Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | # |
2 | # Backlight & LCD drivers configuration | |
3 | # | |
4 | ||
5 | menuconfig BACKLIGHT_LCD_SUPPORT | |
6 | bool "Backlight & LCD device support" | |
7 | help | |
8 | Enable this to be able to choose the drivers for controlling the | |
9 | backlight and the LCD panel on some platforms, for example on PDAs. | |
10 | ||
8fdd5767 HS |
11 | if BACKLIGHT_LCD_SUPPORT |
12 | ||
fa9133c2 DB |
13 | # |
14 | # LCD | |
15 | # | |
16 | config LCD_CLASS_DEVICE | |
17 | tristate "Lowlevel LCD controls" | |
1da177e4 LT |
18 | default m |
19 | help | |
fa9133c2 DB |
20 | This framework adds support for low-level control of LCD. |
21 | Some framebuffer devices connect to platform-specific LCD modules | |
22 | in order to have a platform-specific way to control the flat panel | |
23 | (contrast and applying power to the LCD (not to the backlight!)). | |
1da177e4 LT |
24 | |
25 | To have support for your specific LCD panel you will have to | |
26 | select the proper drivers which depend on this option. | |
27 | ||
8fdd5767 HS |
28 | if LCD_CLASS_DEVICE |
29 | ||
b18250a8 EM |
30 | config LCD_CORGI |
31 | tristate "LCD Panel support for SHARP corgi/spitz model" | |
8fdd5767 | 32 | depends on SPI_MASTER && PXA_SHARPSL |
b18250a8 EM |
33 | help |
34 | Say y here to support the LCD panels usually found on SHARP | |
35 | corgi (C7x0) and spitz (Cxx00) models. | |
36 | ||
e7fb9c4a AP |
37 | config LCD_L4F00242T03 |
38 | tristate "Epson L4F00242T03 LCD" | |
8fdd5767 | 39 | depends on SPI_MASTER && GENERIC_GPIO |
e7fb9c4a AP |
40 | help |
41 | SPI driver for Epson L4F00242T03. This provides basic support | |
42 | for init and powering the LCD up/down through a sysfs interface. | |
43 | ||
5036cc41 MV |
44 | config LCD_LMS283GF05 |
45 | tristate "Samsung LMS283GF05 LCD" | |
8fdd5767 | 46 | depends on SPI_MASTER && GENERIC_GPIO |
5036cc41 MV |
47 | help |
48 | SPI driver for Samsung LMS283GF05. This provides basic support | |
49 | for powering the LCD up/down through a sysfs interface. | |
50 | ||
18f65c79 HS |
51 | config LCD_LTV350QV |
52 | tristate "Samsung LTV350QV LCD Panel" | |
8fdd5767 | 53 | depends on SPI_MASTER |
18f65c79 HS |
54 | help |
55 | If you have a Samsung LTV350QV LCD panel, say y to include a | |
56 | power control driver for it. The panel starts up in power | |
57 | off state, so you need this driver in order to see any | |
58 | output. | |
59 | ||
60 | The LTV350QV panel is present on all ATSTK1000 boards. | |
61 | ||
cccb6d3c BD |
62 | config LCD_ILI9320 |
63 | tristate | |
cccb6d3c BD |
64 | help |
65 | If you have a panel based on the ILI9320 controller chip | |
66 | then say y to include a power driver for it. | |
67 | ||
dd89ccb2 | 68 | config LCD_TDO24M |
f4f6bda0 | 69 | tristate "Toppoly TDO24M and TDO35S LCD Panels support" |
8fdd5767 | 70 | depends on SPI_MASTER |
dd89ccb2 | 71 | help |
f4f6bda0 | 72 | If you have a Toppoly TDO24M/TDO35S series LCD panel, say y here to |
dd89ccb2 EM |
73 | include the support for it. |
74 | ||
cccb6d3c BD |
75 | config LCD_VGG2432A4 |
76 | tristate "VGG2432A4 LCM device support" | |
8fdd5767 | 77 | depends on SPI_MASTER |
cccb6d3c | 78 | select LCD_ILI9320 |
cccb6d3c BD |
79 | help |
80 | If you have a VGG2432A4 panel based on the ILI9320 controller chip | |
81 | then say y to include a power driver for it. | |
82 | ||
c25826a7 BD |
83 | config LCD_PLATFORM |
84 | tristate "Platform LCD controls" | |
c25826a7 BD |
85 | help |
86 | This driver provides a platform-device registered LCD power | |
87 | control interface. | |
88 | ||
fbd1b17b DB |
89 | config LCD_TOSA |
90 | tristate "Sharp SL-6000 LCD Driver" | |
5fc05780 | 91 | depends on I2C && SPI && MACH_TOSA |
fbd1b17b DB |
92 | help |
93 | If you have an Sharp SL-6000 Zaurus say Y to enable a driver | |
94 | for its LCD. | |
95 | ||
9e124435 KE |
96 | config LCD_HP700 |
97 | tristate "HP Jornada 700 series LCD Driver" | |
9e124435 KE |
98 | depends on SA1100_JORNADA720_SSP && !PREEMPT |
99 | default y | |
100 | help | |
101 | If you have an HP Jornada 700 series handheld (710/720/728) | |
102 | say Y to enable LCD control driver. | |
103 | ||
ee378a5c ID |
104 | config LCD_S6E63M0 |
105 | tristate "S6E63M0 AMOLED LCD Driver" | |
106 | depends on SPI && BACKLIGHT_CLASS_DEVICE | |
107 | default n | |
108 | help | |
109 | If you have an S6E63M0 LCD Panel, say Y to enable its | |
110 | LCD control driver. | |
111 | ||
1baf0eb3 DL |
112 | config LCD_LD9040 |
113 | tristate "LD9040 AMOLED LCD Driver" | |
114 | depends on SPI && BACKLIGHT_CLASS_DEVICE | |
115 | default n | |
116 | help | |
117 | If you have an LD9040 Panel, say Y to enable its | |
118 | control driver. | |
119 | ||
a4c8aaa5 JH |
120 | config LCD_AMS369FG06 |
121 | tristate "AMS369FG06 AMOLED LCD Driver" | |
122 | depends on SPI && BACKLIGHT_CLASS_DEVICE | |
123 | default n | |
124 | help | |
125 | If you have an AMS369FG06 AMOLED Panel, say Y to enable its | |
126 | LCD control driver. | |
127 | ||
8fdd5767 HS |
128 | endif # LCD_CLASS_DEVICE |
129 | ||
fa9133c2 DB |
130 | # |
131 | # Backlight | |
132 | # | |
133 | config BACKLIGHT_CLASS_DEVICE | |
134 | tristate "Lowlevel Backlight controls" | |
1da177e4 LT |
135 | default m |
136 | help | |
fa9133c2 DB |
137 | This framework adds support for low-level control of the LCD |
138 | backlight. This includes support for brightness and power. | |
1da177e4 LT |
139 | |
140 | To have support for your specific LCD panel you will have to | |
141 | select the proper drivers which depend on this option. | |
142 | ||
8fdd5767 HS |
143 | if BACKLIGHT_CLASS_DEVICE |
144 | ||
a9a84c37 DB |
145 | config BACKLIGHT_ATMEL_LCDC |
146 | bool "Atmel LCDC Contrast-as-Backlight control" | |
8fdd5767 | 147 | depends on FB_ATMEL |
915190f7 | 148 | default y if MACH_SAM9261EK || MACH_SAM9G10EK || MACH_SAM9263EK |
a9a84c37 DB |
149 | help |
150 | This provides a backlight control internal to the Atmel LCDC | |
151 | driver. If the LCD "contrast control" on your board is wired | |
152 | so it controls the backlight brightness, select this option to | |
153 | export this as a PWM-based backlight control. | |
154 | ||
155 | If in doubt, it's safe to enable this option; it doesn't kick | |
156 | in unless the board's description says it's wired that way. | |
157 | ||
3e074058 HCE |
158 | config BACKLIGHT_ATMEL_PWM |
159 | tristate "Atmel PWM backlight control" | |
8fdd5767 | 160 | depends on ATMEL_PWM |
3e074058 HCE |
161 | help |
162 | Say Y here if you want to use the PWM peripheral in Atmel AT91 and | |
163 | AVR32 devices. This driver will need additional platform data to know | |
164 | which PWM instance to use and how to configure it. | |
165 | ||
166 | To compile this driver as a module, choose M here: the module will be | |
167 | called atmel-pwm-bl. | |
168 | ||
08b3924b HS |
169 | config BACKLIGHT_EP93XX |
170 | tristate "Cirrus EP93xx Backlight Driver" | |
171 | depends on FB_EP93XX | |
172 | help | |
173 | If you have a LCD backlight connected to the BRIGHT output of | |
174 | the EP93xx, say Y here to enable this driver. | |
175 | ||
176 | To compile this driver as a module, choose M here: the module will | |
177 | be called ep93xx_bl. | |
178 | ||
d00ba726 RP |
179 | config BACKLIGHT_GENERIC |
180 | tristate "Generic (aka Sharp Corgi) Backlight Driver" | |
d00ba726 | 181 | default y |
1da177e4 | 182 | help |
c3f8f650 RP |
183 | Say y to enable the generic platform backlight driver previously |
184 | known as the Corgi backlight driver. If you have a Sharp Zaurus | |
d00ba726 | 185 | SL-C7xx, SL-Cxx00 or SL-6000x say y. |
45e2a9b4 | 186 | |
7f26c970 JH |
187 | config BACKLIGHT_LM3533 |
188 | tristate "Backlight Driver for LM3533" | |
189 | depends on BACKLIGHT_CLASS_DEVICE | |
190 | depends on MFD_LM3533 | |
191 | help | |
192 | Say Y to enable the backlight driver for National Semiconductor / TI | |
193 | LM3533 Lighting Power chips. | |
194 | ||
195 | The backlights can be controlled directly, through PWM input, or by | |
196 | the ambient-light-sensor interface. The chip supports 256 brightness | |
197 | levels. | |
198 | ||
e4423781 RP |
199 | config BACKLIGHT_LOCOMO |
200 | tristate "Sharp LOCOMO LCD/Backlight Driver" | |
8fdd5767 | 201 | depends on SHARP_LOCOMO |
e4423781 RP |
202 | default y |
203 | help | |
204 | If you have a Sharp Zaurus SL-5500 (Collie) or SL-5600 (Poodle) say y to | |
205 | enable the LCD/backlight driver. | |
206 | ||
ec072b0f AZ |
207 | config BACKLIGHT_OMAP1 |
208 | tristate "OMAP1 PWL-based LCD Backlight" | |
8fdd5767 | 209 | depends on ARCH_OMAP1 |
ec072b0f AZ |
210 | default y |
211 | help | |
212 | This driver controls the LCD backlight level and power for | |
213 | the PWL module of OMAP1 processors. Say Y if your board | |
214 | uses this hardware. | |
215 | ||
06c6f900 AS |
216 | config BACKLIGHT_HP680 |
217 | tristate "HP Jornada 680 Backlight Driver" | |
8fdd5767 | 218 | depends on SH_HP6XX |
06c6f900 AS |
219 | default y |
220 | help | |
221 | If you have a HP Jornada 680, say y to enable the | |
222 | backlight driver. | |
223 | ||
13a7b5dc KE |
224 | config BACKLIGHT_HP700 |
225 | tristate "HP Jornada 700 series Backlight Driver" | |
13a7b5dc KE |
226 | depends on SA1100_JORNADA720_SSP && !PREEMPT |
227 | default y | |
228 | help | |
229 | If you have an HP Jornada 700 series, | |
230 | say Y to include backlight control driver. | |
231 | ||
7a208463 MJ |
232 | config BACKLIGHT_PROGEAR |
233 | tristate "Frontpath ProGear Backlight Driver" | |
8fdd5767 | 234 | depends on PCI && X86 |
7a208463 MJ |
235 | help |
236 | If you have a Frontpath ProGear say Y to enable the | |
237 | backlight driver. | |
dbe7e429 AH |
238 | |
239 | config BACKLIGHT_CARILLO_RANCH | |
240 | tristate "Intel Carillo Ranch Backlight Driver" | |
8fdd5767 | 241 | depends on LCD_CLASS_DEVICE && PCI && X86 && FB_LE80578 |
dbe7e429 AH |
242 | help |
243 | If you have a Intel LE80578 (Carillo Ranch) say Y to enable the | |
244 | backlight driver. | |
42796d37 | 245 | |
246 | config BACKLIGHT_PWM | |
247 | tristate "Generic PWM based Backlight Driver" | |
8fdd5767 | 248 | depends on HAVE_PWM |
42796d37 | 249 | help |
250 | If you have a LCD backlight adjustable by PWM, say Y to enable | |
251 | this driver. | |
7be35c72 | 252 | |
923ae48b MR |
253 | config BACKLIGHT_DA903X |
254 | tristate "Backlight Driver for DA9030/DA9034 using WLED" | |
8fdd5767 | 255 | depends on PMIC_DA903X |
923ae48b MR |
256 | help |
257 | If you have a LCD backlight connected to the WLED output of DA9030 | |
258 | or DA9034 WLED output, say Y here to enable this driver. | |
259 | ||
6ede3d83 AJ |
260 | config BACKLIGHT_DA9052 |
261 | tristate "Dialog DA9052/DA9053 WLED" | |
262 | depends on PMIC_DA9052 | |
263 | help | |
264 | Enable the Backlight Driver for DA9052-BC and DA9053-AA/Bx PMICs. | |
265 | ||
4f811ef0 HZ |
266 | config BACKLIGHT_MAX8925 |
267 | tristate "Backlight driver for MAX8925" | |
8fdd5767 | 268 | depends on MFD_MAX8925 |
4f811ef0 HZ |
269 | help |
270 | If you have a LCD backlight connected to the WLED output of MAX8925 | |
271 | WLED output, say Y here to enable this driver. | |
272 | ||
39b3dee7 MG |
273 | config BACKLIGHT_APPLE |
274 | tristate "Apple Backlight Driver" | |
b372412e | 275 | depends on X86 && ACPI |
7be35c72 | 276 | help |
39b3dee7 | 277 | If you have an Intel-based Apple say Y to enable a driver for its |
b372412e | 278 | backlight. |
7be35c72 | 279 | |
fbd1b17b DB |
280 | config BACKLIGHT_TOSA |
281 | tristate "Sharp SL-6000 Backlight Driver" | |
8fdd5767 | 282 | depends on I2C && MACH_TOSA && LCD_TOSA |
fbd1b17b DB |
283 | help |
284 | If you have an Sharp SL-6000 Zaurus say Y to enable a driver | |
285 | for its backlight | |
286 | ||
d03ebb12 CN |
287 | config BACKLIGHT_SAHARA |
288 | tristate "Tabletkiosk Sahara Touch-iT Backlight Driver" | |
8fdd5767 | 289 | depends on X86 |
d03ebb12 CN |
290 | help |
291 | If you have a Tabletkiosk Sahara Touch-iT, say y to enable the | |
292 | backlight driver. | |
a4f3d55c MB |
293 | |
294 | config BACKLIGHT_WM831X | |
295 | tristate "WM831x PMIC Backlight Driver" | |
8fdd5767 | 296 | depends on MFD_WM831X |
a4f3d55c MB |
297 | help |
298 | If you have a backlight driven by the ISINK and DCDC of a | |
299 | WM831x PMIC say y to enable the backlight driver for it. | |
3b96ea9e | 300 | |
a7998cec MH |
301 | config BACKLIGHT_ADP5520 |
302 | tristate "Backlight Driver for ADP5520/ADP5501 using WLED" | |
8fdd5767 | 303 | depends on PMIC_ADP5520 |
a7998cec MH |
304 | help |
305 | If you have a LCD backlight connected to the BST/BL_SNK output of | |
306 | ADP5520 or ADP5501, say Y here to enable this driver. | |
307 | ||
308 | To compile this driver as a module, choose M here: the module will | |
309 | be called adp5520_bl. | |
310 | ||
82fd53b7 | 311 | config BACKLIGHT_ADP8860 |
c7c06d8a | 312 | tristate "Backlight Driver for ADP8860/ADP8861/ADP8863 using WLED" |
82fd53b7 MH |
313 | depends on BACKLIGHT_CLASS_DEVICE && I2C |
314 | select NEW_LEDS | |
315 | select LEDS_CLASS | |
316 | help | |
c7c06d8a MH |
317 | If you have a LCD backlight connected to the ADP8860, ADP8861 or |
318 | ADP8863 say Y here to enable this driver. | |
82fd53b7 MH |
319 | |
320 | To compile this driver as a module, choose M here: the module will | |
321 | be called adp8860_bl. | |
322 | ||
a59ec1e7 MH |
323 | config BACKLIGHT_ADP8870 |
324 | tristate "Backlight Driver for ADP8870 using WLED" | |
325 | depends on BACKLIGHT_CLASS_DEVICE && I2C | |
326 | select NEW_LEDS | |
327 | select LEDS_CLASS | |
328 | help | |
329 | If you have a LCD backlight connected to the ADP8870, | |
330 | say Y here to enable this driver. | |
331 | ||
332 | To compile this driver as a module, choose M here: the module will | |
333 | be called adp8870_bl. | |
334 | ||
d07e8bf8 HZ |
335 | config BACKLIGHT_88PM860X |
336 | tristate "Backlight Driver for 88PM8606 using WLED" | |
8fdd5767 | 337 | depends on MFD_88PM860X |
d07e8bf8 HZ |
338 | help |
339 | Say Y to enable the backlight driver for Marvell 88PM8606. | |
340 | ||
2ddfd12f LPC |
341 | config BACKLIGHT_PCF50633 |
342 | tristate "Backlight driver for NXP PCF50633 MFD" | |
343 | depends on BACKLIGHT_CLASS_DEVICE && MFD_PCF50633 | |
344 | help | |
345 | If you have a backlight driven by a NXP PCF50633 MFD, say Y here to | |
346 | enable its driver. | |
347 | ||
4b0d711b | 348 | config BACKLIGHT_AAT2870 |
70d32719 | 349 | tristate "AnalogicTech AAT2870 Backlight" |
4b0d711b JP |
350 | depends on BACKLIGHT_CLASS_DEVICE && MFD_AAT2870_CORE |
351 | help | |
352 | If you have a AnalogicTech AAT2870 say Y to enable the | |
353 | backlight driver. | |
354 | ||
7be865ab KM |
355 | config BACKLIGHT_LP855X |
356 | tristate "Backlight driver for TI LP855X" | |
357 | depends on BACKLIGHT_CLASS_DEVICE && I2C | |
358 | help | |
359 | This supports TI LP8550, LP8551, LP8552, LP8553 and LP8556 | |
360 | backlight driver. | |
361 | ||
c8df7428 CG |
362 | config BACKLIGHT_OT200 |
363 | tristate "Backlight driver for ot200 visualisation device" | |
2df5e129 | 364 | depends on BACKLIGHT_CLASS_DEVICE && CS5535_MFGPT && GPIO_CS5535 |
c8df7428 CG |
365 | help |
366 | To compile this driver as a module, choose M here: the module will be | |
367 | called ot200_bl. | |
368 | ||
35c1682c GI |
369 | config BACKLIGHT_PANDORA |
370 | tristate "Backlight driver for Pandora console" | |
371 | depends on TWL4030_CORE | |
372 | help | |
373 | If you have a Pandora console, say Y to enable the | |
374 | backlight driver. | |
375 | ||
8fdd5767 HS |
376 | endif # BACKLIGHT_CLASS_DEVICE |
377 | ||
378 | endif # BACKLIGHT_LCD_SUPPORT |