[deliverable/linux.git] / drivers / w1 / slaves / Kconfig

#
# 1-wire slaves configuration
#

menu "1-wire Slaves"

config W1_SLAVE_THERM
	tristate "Thermal family implementation"
	help
	  Say Y here if you want to connect 1-wire thermal sensors to your
	  wire.

config W1_SLAVE_SMEM
	tristate "Simple 64bit memory family implementation"
	help
	  Say Y here if you want to connect 1-wire
	  simple 64bit memory rom(ds2401/ds2411/ds1990*) to your wire.

config W1_SLAVE_DS2408
        tristate "8-Channel Addressable Switch (IO Expander) 0x29 family support (DS2408)"
        help
          Say Y here if you want to use a 1-wire

		  DS2408 8-Channel Addressable Switch device support

config W1_SLAVE_DS2423
	tristate "Counter 1-wire device (DS2423)"
	select CRC16
	help
	  If you enable this you can read the counter values available
	  in the DS2423 chipset from the w1_slave file under the
	  sys file system.

	  Say Y here if you want to use a 1-wire
	  counter family device (DS2423).

config W1_SLAVE_DS2431
	tristate "1kb EEPROM family support (DS2431)"
	help
	  Say Y here if you want to use a 1-wire
	  1kb EEPROM family device (DS2431)

config W1_SLAVE_DS2433
	tristate "4kb EEPROM family support (DS2433)"
	help
	  Say Y here if you want to use a 1-wire
	  4kb EEPROM family device (DS2433).

config W1_SLAVE_DS2433_CRC
	bool "Protect DS2433 data with a CRC16"
	depends on W1_SLAVE_DS2433
	select CRC16
	help
	  Say Y here to protect DS2433 data with a CRC16.
	  Each block has 30 bytes of data and a two byte CRC16.
	  Full block writes are only allowed if the CRC is valid.

config W1_SLAVE_DS2760
	tristate "Dallas 2760 battery monitor chip (HP iPAQ & others)"
	depends on W1
	help
	  If you enable this you will have the DS2760 battery monitor
	  chip support.

	  The battery monitor chip is used in many batteries/devices
	  as the one who is responsible for charging/discharging/monitoring
	  Li+ batteries.

	  If you are unsure, say N.

config W1_SLAVE_DS2780
	tristate "Dallas 2780 battery monitor chip"
	depends on W1
	help
	  If you enable this you will have the DS2780 battery monitor
	  chip support.

	  The battery monitor chip is used in many batteries/devices
	  as the one who is responsible for charging/discharging/monitoring
	  Li+ batteries.

	  If you are unsure, say N.

config W1_SLAVE_DS2781
	tristate "Dallas 2781 battery monitor chip"
	depends on W1
	help
	  If you enable this you will have the DS2781 battery monitor
	  chip support.

	  The battery monitor chip is used in many batteries/devices
	  as the one who is responsible for charging/discharging/monitoring
	  Li+ batteries.

	  If you are unsure, say N.

config W1_SLAVE_DS28E04
	tristate "4096-Bit Addressable 1-Wire EEPROM with PIO (DS28E04-100)"
	depends on W1
	help
	  Say Y here if you want to use a 1-wire
	  4kb EEPROM with PIO family device (DS28E04).

config W1_SLAVE_BQ27000
	tristate "BQ27000 slave support"
	depends on W1
	help
	  Say Y here if you want to use a hdq
	  bq27000 slave support.

endmenu
Commit	Line	Data
bd529cfb EP	1	#
	2	# 1-wire slaves configuration
	3	#
	4
	5	menu "1-wire Slaves"
bd529cfb EP	6
	7	config W1_SLAVE_THERM
	8	tristate "Thermal family implementation"
bd529cfb	9	help
89040b21	10	Say Y here if you want to connect 1-wire thermal sensors to your
bd529cfb EP	11	wire.
	12
	13	config W1_SLAVE_SMEM
	14	tristate "Simple 64bit memory family implementation"
bd529cfb EP	15	help
bd529cfb EP	16	Say Y here if you want to connect 1-wire
89040b21	17	simple 64bit memory rom(ds2401/ds2411/ds1990*) to your wire.
bd529cfb	18
89610274 JFD	19	config W1_SLAVE_DS2408
	20	tristate "8-Channel Addressable Switch (IO Expander) 0x29 family support (DS2408)"
	21	help
	22	Say Y here if you want to use a 1-wire
	23
	24	DS2408 8-Channel Addressable Switch device support
	25
17fecb55 ML	26	config W1_SLAVE_DS2423
	27	tristate "Counter 1-wire device (DS2423)"
	28	select CRC16
	29	help
	30	If you enable this you can read the counter values available
	31	in the DS2423 chipset from the w1_slave file under the
	32	sys file system.
	33
	34	Say Y here if you want to use a 1-wire
	35	counter family device (DS2423).
	36
8ca2f156 HRK	37	config W1_SLAVE_DS2431
	38	tristate "1kb EEPROM family support (DS2431)"
	39	help
	40	Say Y here if you want to use a 1-wire
	41	1kb EEPROM family device (DS2431)
	42
bd529cfb EP	43	config W1_SLAVE_DS2433
bd529cfb EP	44	tristate "4kb EEPROM family support (DS2433)"
bd529cfb EP	45	help
	46	Say Y here if you want to use a 1-wire
	47	4kb EEPROM family device (DS2433).
	48
	49	config W1_SLAVE_DS2433_CRC
	50	bool "Protect DS2433 data with a CRC16"
f621e1c7	51	depends on W1_SLAVE_DS2433
bd529cfb EP	52	select CRC16
	53	help
	54	Say Y here to protect DS2433 data with a CRC16.
	55	Each block has 30 bytes of data and a two byte CRC16.
	56	Full block writes are only allowed if the CRC is valid.
	57
d7ce6d1d AV	58	config W1_SLAVE_DS2760
	59	tristate "Dallas 2760 battery monitor chip (HP iPAQ & others)"
	60	depends on W1
	61	help
	62	If you enable this you will have the DS2760 battery monitor
	63	chip support.
	64
	65	The battery monitor chip is used in many batteries/devices
	66	as the one who is responsible for charging/discharging/monitoring
	67	Li+ batteries.
	68
	69	If you are unsure, say N.
	70
275ac746 CB	71	config W1_SLAVE_DS2780
	72	tristate "Dallas 2780 battery monitor chip"
	73	depends on W1
	74	help
	75	If you enable this you will have the DS2780 battery monitor
	76	chip support.
	77
	78	The battery monitor chip is used in many batteries/devices
	79	as the one who is responsible for charging/discharging/monitoring
	80	Li+ batteries.
	81
	82	If you are unsure, say N.
	83
fef37e9a RS	84	config W1_SLAVE_DS2781
	85	tristate "Dallas 2781 battery monitor chip"
	86	depends on W1
	87	help
	88	If you enable this you will have the DS2781 battery monitor
	89	chip support.
	90
	91	The battery monitor chip is used in many batteries/devices
	92	as the one who is responsible for charging/discharging/monitoring
	93	Li+ batteries.
	94
	95	If you are unsure, say N.
	96
f19420c1 MF	97	config W1_SLAVE_DS28E04
	98	tristate "4096-Bit Addressable 1-Wire EEPROM with PIO (DS28E04-100)"
	99	depends on W1
	100	help
	101	Say Y here if you want to use a 1-wire
	102	4kb EEPROM with PIO family device (DS28E04).
	103
cfbc6190 MC	104	config W1_SLAVE_BQ27000
	105	tristate "BQ27000 slave support"
	106	depends on W1
	107	help
	108	Say Y here if you want to use a hdq
	109	bq27000 slave support.
	110
bd529cfb	111	endmenu