Commit | Line | Data |
---|---|---|
2571583a | 1 | @c Copyright (C) 2009-2017 Free Software Foundation, Inc. |
11c19e16 MS |
2 | @c This is part of the GAS manual. |
3 | @c For copying conditions, see the file as.texinfo. | |
4 | @ifset GENERIC | |
5 | @page | |
6 | @node S/390-Dependent | |
7 | @chapter IBM S/390 Dependent Features | |
8 | @end ifset | |
9 | @ifclear GENERIC | |
10 | @node Machine Dependencies | |
11 | @chapter IBM S/390 Dependent Features | |
12 | @end ifclear | |
13 | ||
14 | @cindex s390 support | |
15 | ||
16 | The s390 version of @code{@value{AS}} supports two architectures modes | |
64025b4e | 17 | and eleven chip levels. The architecture modes are the Enterprise System |
11c19e16 | 18 | Architecture (ESA) and the newer z/Architecture mode. The chip levels |
952c3f51 | 19 | are g5 (or arch3), g6, z900 (or arch5), z990 (or arch6), z9-109, z9-ec |
64025b4e | 20 | (or arch7), z10 (or arch8), z196 (or arch9), zEC12 (or arch10), z13 |
47826cdb | 21 | (or arch11), and z14 (or arch12). |
11c19e16 MS |
22 | |
23 | @menu | |
24 | * s390 Options:: Command-line Options. | |
25 | * s390 Characters:: Special Characters. | |
26 | * s390 Syntax:: Assembler Instruction syntax. | |
27 | * s390 Directives:: Assembler Directives. | |
28 | * s390 Floating Point:: Floating Point. | |
29 | @end menu | |
30 | ||
31 | @node s390 Options | |
32 | @section Options | |
33 | @cindex options for s390 | |
34 | @cindex s390 options | |
35 | ||
36 | The following table lists all available s390 specific options: | |
34bca508 | 37 | |
11c19e16 MS |
38 | @table @code |
39 | @cindex @samp{-m31} option, s390 | |
40 | @cindex @samp{-m64} option, s390 | |
41 | @item -m31 | -m64 | |
42 | Select 31- or 64-bit ABI implying a word size of 32- or 64-bit. | |
43 | ||
44 | These options are only available with the ELF object file format, and | |
45 | require that the necessary BFD support has been included (on a 31-bit | |
46 | platform you must add --enable-64-bit-bfd on the call to the configure | |
47 | script to enable 64-bit usage and use s390x as target platform). | |
48 | ||
49 | @cindex @samp{-mesa} option, s390 | |
50 | @cindex @samp{-mzarch} option, s390 | |
51 | @item -mesa | -mzarch | |
52 | Select the architecture mode, either the Enterprise System Architecture | |
53 | (esa) mode or the z/Architecture mode (zarch). | |
54 | ||
55 | The 64-bit instructions are only available with the z/Architecture mode. | |
56 | The combination of @samp{-m64} and @samp{-mesa} results in a warning | |
57 | message. | |
58 | ||
59 | @cindex @samp{-march=} option, s390 | |
60 | @item -march=@var{CPU} | |
61 | This option specifies the target processor. The following processor names | |
34bca508 | 62 | are recognized: |
952c3f51 | 63 | @code{g5} (or @code{arch3}), |
11c19e16 | 64 | @code{g6}, |
952c3f51 AK |
65 | @code{z900} (or @code{arch5}), |
66 | @code{z990} (or @code{arch6}), | |
11c19e16 | 67 | @code{z9-109}, |
952c3f51 AK |
68 | @code{z9-ec} (or @code{arch7}), |
69 | @code{z10} (or @code{arch8}), | |
70 | @code{z196} (or @code{arch9}), | |
71 | @code{zEC12} (or @code{arch10}) and | |
72 | @code{z13} (or @code{arch11}). | |
73 | ||
74 | Assembling an instruction that is not supported on the target | |
75 | processor results in an error message. | |
76 | ||
77 | The processor names starting with @code{arch} refer to the edition | |
78 | number in the Principle of Operations manual. They can be used as | |
79 | alternate processor names and have been added for compatibility with | |
80 | the IBM XL compiler. | |
81 | ||
82 | @code{arch3}, @code{g5} and @code{g6} cannot be used with the | |
83 | @samp{-mzarch} option since the z/Architecture mode is not supported | |
84 | on these processor levels. | |
85 | ||
86 | There is no @code{arch4} option supported. @code{arch4} matches | |
87 | @code{-march=arch5 -mesa}. | |
11c19e16 MS |
88 | |
89 | @cindex @samp{-mregnames} option, s390 | |
90 | @item -mregnames | |
91 | Allow symbolic names for registers. | |
92 | ||
93 | @cindex @samp{-mno-regnames} option, s390 | |
94 | @item -mno-regnames | |
95 | Do not allow symbolic names for registers. | |
96 | ||
97 | @cindex @samp{-mwarn-areg-zero} option, s390 | |
98 | @item -mwarn-areg-zero | |
99 | Warn whenever the operand for a base or index register has been specified | |
100 | but evaluates to zero. This can indicate the misuse of general purpose | |
101 | register 0 as an address register. | |
102 | ||
103 | @end table | |
104 | ||
105 | @node s390 Characters | |
106 | @section Special Characters | |
107 | @cindex line comment character, s390 | |
108 | @cindex s390 line comment character | |
109 | ||
110 | @samp{#} is the line comment character. | |
111 | ||
7c31ae13 NC |
112 | If a @samp{#} appears as the first character of a line then the whole |
113 | line is treated as a comment, but in this case the line could also be | |
114 | a logical line number directive (@pxref{Comments}) or a preprocessor | |
115 | control command (@pxref{Preprocessing}). | |
116 | ||
117 | @cindex line separator, s390 | |
118 | @cindex statement separator, s390 | |
119 | @cindex s390 line separator | |
120 | The @samp{;} character can be used instead of a newline to separate | |
121 | statements. | |
122 | ||
11c19e16 MS |
123 | @node s390 Syntax |
124 | @section Instruction syntax | |
125 | @cindex instruction syntax, s390 | |
126 | @cindex s390 instruction syntax | |
127 | ||
34bca508 L |
128 | The assembler syntax closely follows the syntax outlined in |
129 | Enterprise Systems Architecture/390 Principles of Operation (SA22-7201) | |
130 | and the z/Architecture Principles of Operation (SA22-7832). | |
11c19e16 MS |
131 | |
132 | Each instruction has two major parts, the instruction mnemonic | |
133 | and the instruction operands. The instruction format varies. | |
134 | ||
135 | @menu | |
136 | * s390 Register:: Register Naming | |
137 | * s390 Mnemonics:: Instruction Mnemonics | |
138 | * s390 Operands:: Instruction Operands | |
139 | * s390 Formats:: Instruction Formats | |
140 | * s390 Aliases:: Instruction Aliases | |
141 | * s390 Operand Modifier:: Instruction Operand Modifier | |
142 | * s390 Instruction Marker:: Instruction Marker | |
143 | * s390 Literal Pool Entries:: Literal Pool Entries | |
144 | @end menu | |
145 | ||
146 | @node s390 Register | |
147 | @subsection Register naming | |
148 | @cindex register naming, s390 | |
149 | @cindex s390 register naming | |
150 | ||
151 | The @code{@value{AS}} recognizes a number of predefined symbols for the | |
152 | various processor registers. A register specification in one of the | |
153 | instruction formats is an unsigned integer between 0 and 15. The specific | |
154 | instruction and the position of the register in the instruction format | |
155 | denotes the type of the register. The register symbols are prefixed with | |
156 | @samp{%}: | |
157 | ||
158 | @display | |
159 | @multitable {%rN} {the 16 general purpose registers, 0 <= N <= 15} | |
160 | @item %rN @tab the 16 general purpose registers, 0 <= N <= 15 | |
161 | @item %fN @tab the 16 floating point registers, 0 <= N <= 15 | |
162 | @item %aN @tab the 16 access registers, 0 <= N <= 15 | |
163 | @item %cN @tab the 16 control registers, 0 <= N <= 15 | |
164 | @item %lit @tab an alias for the general purpose register %r13 | |
165 | @item %sp @tab an alias for the general purpose register %r15 | |
166 | @end multitable | |
167 | @end display | |
168 | ||
169 | @node s390 Mnemonics | |
170 | @subsection Instruction Mnemonics | |
171 | @cindex instruction mnemonics, s390 | |
172 | @cindex s390 instruction mnemonics | |
173 | ||
174 | All instructions documented in the Principles of Operation are supported | |
175 | with the mnemonic and order of operands as described. | |
176 | The instruction mnemonic identifies the instruction format | |
177 | (@ref{s390 Formats}) and the specific operation code for the instruction. | |
178 | For example, the @samp{lr} mnemonic denotes the instruction format @samp{RR} | |
179 | with the operation code @samp{0x18}. | |
180 | ||
181 | The definition of the various mnemonics follows a scheme, where the first | |
182 | character usually hint at the type of the instruction: | |
183 | ||
184 | @display | |
185 | @multitable {sla, sll} {if r is the last character the instruction operates on registers} | |
186 | @item a @tab add instruction, for example @samp{al} for add logical 32-bit | |
187 | @item b @tab branch instruction, for example @samp{bc} for branch on condition | |
188 | @item c @tab compare or convert instruction, for example @samp{cr} for compare | |
189 | register 32-bit | |
190 | @item d @tab divide instruction, for example @samp{dlr} devide logical register | |
191 | 64-bit to 32-bit | |
192 | @item i @tab insert instruction, for example @samp{ic} insert character | |
193 | @item l @tab load instruction, for example @samp{ltr} load and test register | |
194 | @item mv @tab move instruction, for example @samp{mvc} move character | |
195 | @item m @tab multiply instruction, for example @samp{mh} multiply halfword | |
196 | @item n @tab and instruction, for example @samp{ni} and immediate | |
197 | @item o @tab or instruction, for example @samp{oc} or character | |
198 | @item sla, sll @tab shift left single instruction | |
199 | @item sra, srl @tab shift right single instruction | |
200 | @item st @tab store instruction, for example @samp{stm} store multiple | |
201 | @item s @tab subtract instruction, for example @samp{slr} subtract | |
202 | logical 32-bit | |
203 | @item t @tab test or translate instruction, of example @samp{tm} test under mask | |
204 | @item x @tab exclusive or instruction, for example @samp{xc} exclusive or | |
205 | character | |
206 | @end multitable | |
207 | @end display | |
208 | ||
209 | Certain characters at the end of the mnemonic may describe a property | |
210 | of the instruction: | |
211 | ||
212 | @display | |
213 | @multitable {c} {if r is the last character the instruction operates on registers} | |
214 | @item c @tab the instruction uses a 8-bit character operand | |
215 | @item f @tab the instruction extends a 32-bit operand to 64 bit | |
216 | @item g @tab the operands are treated as 64-bit values | |
217 | @item h @tab the operand uses a 16-bit halfword operand | |
218 | @item i @tab the instruction uses an immediate operand | |
219 | @item l @tab the instruction uses unsigned, logical operands | |
220 | @item m @tab the instruction uses a mask or operates on multiple values | |
221 | @item r @tab if r is the last character, the instruction operates on registers | |
222 | @item y @tab the instruction uses 20-bit displacements | |
223 | @end multitable | |
224 | @end display | |
225 | ||
226 | There are many exceptions to the scheme outlined in the above lists, in | |
33eaf5de | 227 | particular for the privileged instructions. For non-privileged |
11c19e16 MS |
228 | instruction it works quite well, for example the instruction @samp{clgfr} |
229 | c: compare instruction, l: unsigned operands, g: 64-bit operands, | |
230 | f: 32- to 64-bit extension, r: register operands. The instruction compares | |
231 | an 64-bit value in a register with the zero extended 32-bit value from | |
232 | a second register. | |
233 | For a complete list of all mnemonics see appendix B in the Principles | |
234 | of Operation. | |
235 | ||
236 | @node s390 Operands | |
237 | @subsection Instruction Operands | |
238 | @cindex instruction operands, s390 | |
239 | @cindex s390 instruction operands | |
240 | ||
241 | Instruction operands can be grouped into three classes, operands located | |
242 | in registers, immediate operands, and operands in storage. | |
243 | ||
244 | A register operand can be located in general, floating-point, access, | |
245 | or control register. The register is identified by a four-bit field. | |
246 | The field containing the register operand is called the R field. | |
247 | ||
248 | Immediate operands are contained within the instruction and can have | |
249 | 8, 16 or 32 bits. The field containing the immediate operand is called | |
250 | the I field. Dependent on the instruction the I field is either signed | |
251 | or unsigned. | |
252 | ||
253 | A storage operand consists of an address and a length. The address of a | |
254 | storage operands can be specified in any of these ways: | |
255 | ||
256 | @itemize | |
257 | @item The content of a single general R | |
258 | @item The sum of the content of a general register called the base | |
259 | register B plus the content of a displacement field D | |
260 | @item The sum of the contents of two general registers called the | |
261 | index register X and the base register B plus the content of a | |
262 | displacement field | |
263 | @item The sum of the current instruction address and a 32-bit signed | |
264 | immediate field multiplied by two. | |
265 | @end itemize | |
266 | ||
267 | The length of a storage operand can be: | |
268 | ||
269 | @itemize | |
270 | @item Implied by the instruction | |
271 | @item Specified by a bitmask | |
272 | @item Specified by a four-bit or eight-bit length field L | |
273 | @item Specified by the content of a general register | |
274 | @end itemize | |
275 | ||
276 | The notation for storage operand addresses formed from multiple fields is | |
277 | as follows: | |
278 | ||
279 | @table @code | |
280 | @item Dn(Bn) | |
281 | the address for operand number n is formed from the content of general | |
282 | register Bn called the base register and the displacement field Dn. | |
283 | @item Dn(Xn,Bn) | |
284 | the address for operand number n is formed from the content of general | |
285 | register Xn called the index register, general register Bn called the | |
286 | base register and the displacement field Dn. | |
287 | @item Dn(Ln,Bn) | |
288 | the address for operand number n is formed from the content of general | |
33eaf5de | 289 | register Bn called the base register and the displacement field Dn. |
11c19e16 MS |
290 | The length of the operand n is specified by the field Ln. |
291 | @end table | |
292 | ||
293 | The base registers Bn and the index registers Xn of a storage operand can | |
294 | be skipped. If Bn and Xn are skipped, a zero will be stored to the operand | |
295 | field. The notation changes as follows: | |
296 | ||
297 | @display | |
298 | @multitable @columnfractions 0.30 0.30 | |
299 | @headitem full notation @tab short notation | |
300 | @item Dn(0,Bn) @tab Dn(Bn) | |
301 | @item Dn(0,0) @tab Dn | |
302 | @item Dn(0) @tab Dn | |
303 | @item Dn(Ln,0) @tab Dn(Ln) | |
304 | @end multitable | |
305 | @end display | |
306 | ||
307 | ||
308 | @node s390 Formats | |
309 | @subsection Instruction Formats | |
310 | @cindex instruction formats, s390 | |
311 | @cindex s390 instruction formats | |
312 | ||
313 | The Principles of Operation manuals lists 26 instruction formats where | |
314 | some of the formats have multiple variants. For the @samp{.insn} | |
34bca508 | 315 | pseudo directive the assembler recognizes some of the formats. |
11c19e16 MS |
316 | Typically, the most general variant of the instruction format is used |
317 | by the @samp{.insn} directive. | |
318 | ||
319 | The following table lists the abbreviations used in the table of | |
320 | instruction formats: | |
321 | ||
322 | @display | |
323 | @multitable {OpCode / OpCd} {Displacement lower 12 bits for operand x.} | |
324 | @item OpCode / OpCd @tab Part of the op code. | |
325 | @item Bx @tab Base register number for operand x. | |
326 | @item Dx @tab Displacement for operand x. | |
327 | @item DLx @tab Displacement lower 12 bits for operand x. | |
328 | @item DHx @tab Displacement higher 8-bits for operand x. | |
329 | @item Rx @tab Register number for operand x. | |
330 | @item Xx @tab Index register number for operand x. | |
331 | @item Ix @tab Signed immediate for operand x. | |
332 | @item Ux @tab Unsigned immediate for operand x. | |
333 | @end multitable | |
334 | @end display | |
335 | ||
336 | An instruction is two, four, or six bytes in length and must be aligned | |
337 | on a 2 byte boundary. The first two bits of the instruction specify the | |
338 | length of the instruction, 00 indicates a two byte instruction, 01 and 10 | |
339 | indicates a four byte instruction, and 11 indicates a six byte instruction. | |
340 | ||
341 | The following table lists the s390 instruction formats that are available | |
342 | with the @samp{.insn} pseudo directive: | |
343 | ||
344 | @table @code | |
345 | @item E format | |
346 | @verbatim | |
347 | +-------------+ | |
348 | | OpCode | | |
349 | +-------------+ | |
350 | 0 15 | |
351 | @end verbatim | |
352 | ||
353 | @item RI format: <insn> R1,I2 | |
354 | @verbatim | |
355 | +--------+----+----+------------------+ | |
356 | | OpCode | R1 |OpCd| I2 | | |
357 | +--------+----+----+------------------+ | |
358 | 0 8 12 16 31 | |
359 | @end verbatim | |
360 | ||
361 | @item RIE format: <insn> R1,R3,I2 | |
362 | @verbatim | |
363 | +--------+----+----+------------------+--------+--------+ | |
364 | | OpCode | R1 | R3 | I2 |////////| OpCode | | |
365 | +--------+----+----+------------------+--------+--------+ | |
366 | 0 8 12 16 32 40 47 | |
367 | @end verbatim | |
368 | ||
369 | @item RIL format: <insn> R1,I2 | |
370 | @verbatim | |
371 | +--------+----+----+------------------------------------+ | |
372 | | OpCode | R1 |OpCd| I2 | | |
373 | +--------+----+----+------------------------------------+ | |
374 | 0 8 12 16 47 | |
375 | @end verbatim | |
376 | ||
377 | @item RILU format: <insn> R1,U2 | |
378 | @verbatim | |
379 | +--------+----+----+------------------------------------+ | |
380 | | OpCode | R1 |OpCd| U2 | | |
381 | +--------+----+----+------------------------------------+ | |
382 | 0 8 12 16 47 | |
383 | @end verbatim | |
384 | ||
385 | @item RIS format: <insn> R1,I2,M3,D4(B4) | |
386 | @verbatim | |
387 | +--------+----+----+----+-------------+--------+--------+ | |
388 | | OpCode | R1 | M3 | B4 | D4 | I2 | Opcode | | |
389 | +--------+----+----+----+-------------+--------+--------+ | |
390 | 0 8 12 16 20 32 36 47 | |
391 | @end verbatim | |
392 | ||
393 | @item RR format: <insn> R1,R2 | |
394 | @verbatim | |
395 | +--------+----+----+ | |
396 | | OpCode | R1 | R2 | | |
397 | +--------+----+----+ | |
34bca508 | 398 | 0 8 12 15 |
11c19e16 MS |
399 | @end verbatim |
400 | ||
401 | @item RRE format: <insn> R1,R2 | |
402 | @verbatim | |
403 | +------------------+--------+----+----+ | |
404 | | OpCode |////////| R1 | R2 | | |
405 | +------------------+--------+----+----+ | |
406 | 0 16 24 28 31 | |
407 | @end verbatim | |
408 | ||
409 | @item RRF format: <insn> R1,R2,R3,M4 | |
410 | @verbatim | |
411 | +------------------+----+----+----+----+ | |
412 | | OpCode | R3 | M4 | R1 | R2 | | |
413 | +------------------+----+----+----+----+ | |
414 | 0 16 20 24 28 31 | |
415 | @end verbatim | |
416 | ||
417 | @item RRS format: <insn> R1,R2,M3,D4(B4) | |
418 | @verbatim | |
419 | +--------+----+----+----+-------------+----+----+--------+ | |
420 | | OpCode | R1 | R3 | B4 | D4 | M3 |////| OpCode | | |
421 | +--------+----+----+----+-------------+----+----+--------+ | |
422 | 0 8 12 16 20 32 36 40 47 | |
423 | @end verbatim | |
424 | ||
425 | @item RS format: <insn> R1,R3,D2(B2) | |
426 | @verbatim | |
427 | +--------+----+----+----+-------------+ | |
428 | | OpCode | R1 | R3 | B2 | D2 | | |
429 | +--------+----+----+----+-------------+ | |
430 | 0 8 12 16 20 31 | |
431 | @end verbatim | |
432 | ||
433 | @item RSE format: <insn> R1,R3,D2(B2) | |
434 | @verbatim | |
435 | +--------+----+----+----+-------------+--------+--------+ | |
436 | | OpCode | R1 | R3 | B2 | D2 |////////| OpCode | | |
437 | +--------+----+----+----+-------------+--------+--------+ | |
438 | 0 8 12 16 20 32 40 47 | |
439 | @end verbatim | |
440 | ||
441 | @item RSI format: <insn> R1,R3,I2 | |
442 | @verbatim | |
443 | +--------+----+----+------------------------------------+ | |
444 | | OpCode | R1 | R3 | I2 | | |
445 | +--------+----+----+------------------------------------+ | |
446 | 0 8 12 16 47 | |
447 | @end verbatim | |
448 | ||
449 | @item RSY format: <insn> R1,R3,D2(B2) | |
450 | @verbatim | |
451 | +--------+----+----+----+-------------+--------+--------+ | |
452 | | OpCode | R1 | R3 | B2 | DL2 | DH2 | OpCode | | |
453 | +--------+----+----+----+-------------+--------+--------+ | |
454 | 0 8 12 16 20 32 40 47 | |
455 | @end verbatim | |
456 | ||
457 | @item RX format: <insn> R1,D2(X2,B2) | |
458 | @verbatim | |
459 | +--------+----+----+----+-------------+ | |
460 | | OpCode | R1 | X2 | B2 | D2 | | |
461 | +--------+----+----+----+-------------+ | |
462 | 0 8 12 16 20 31 | |
463 | @end verbatim | |
464 | ||
465 | @item RXE format: <insn> R1,D2(X2,B2) | |
466 | @verbatim | |
467 | +--------+----+----+----+-------------+--------+--------+ | |
468 | | OpCode | R1 | X2 | B2 | D2 |////////| OpCode | | |
469 | +--------+----+----+----+-------------+--------+--------+ | |
470 | 0 8 12 16 20 32 40 47 | |
471 | @end verbatim | |
472 | ||
473 | @item RXF format: <insn> R1,R3,D2(X2,B2) | |
474 | @verbatim | |
475 | +--------+----+----+----+-------------+----+---+--------+ | |
476 | | OpCode | R3 | X2 | B2 | D2 | R1 |///| OpCode | | |
477 | +--------+----+----+----+-------------+----+---+--------+ | |
478 | 0 8 12 16 20 32 36 40 47 | |
479 | @end verbatim | |
480 | ||
481 | @item RXY format: <insn> R1,D2(X2,B2) | |
482 | @verbatim | |
483 | +--------+----+----+----+-------------+--------+--------+ | |
484 | | OpCode | R1 | X2 | B2 | DL2 | DH2 | OpCode | | |
485 | +--------+----+----+----+-------------+--------+--------+ | |
486 | 0 8 12 16 20 32 36 40 47 | |
487 | @end verbatim | |
488 | ||
489 | @item S format: <insn> D2(B2) | |
490 | @verbatim | |
491 | +------------------+----+-------------+ | |
492 | | OpCode | B2 | D2 | | |
493 | +------------------+----+-------------+ | |
494 | 0 16 20 31 | |
495 | @end verbatim | |
496 | ||
497 | @item SI format: <insn> D1(B1),I2 | |
498 | @verbatim | |
499 | +--------+---------+----+-------------+ | |
500 | | OpCode | I2 | B1 | D1 | | |
501 | +--------+---------+----+-------------+ | |
502 | 0 8 16 20 31 | |
503 | @end verbatim | |
504 | ||
505 | @item SIY format: <insn> D1(B1),U2 | |
506 | @verbatim | |
507 | +--------+---------+----+-------------+--------+--------+ | |
508 | | OpCode | I2 | B1 | DL1 | DH1 | OpCode | | |
509 | +--------+---------+----+-------------+--------+--------+ | |
510 | 0 8 16 20 32 36 40 47 | |
511 | @end verbatim | |
512 | ||
513 | @item SIL format: <insn> D1(B1),I2 | |
514 | @verbatim | |
515 | +------------------+----+-------------+-----------------+ | |
516 | | OpCode | B1 | D1 | I2 | | |
517 | +------------------+----+-------------+-----------------+ | |
518 | 0 16 20 32 47 | |
519 | @end verbatim | |
520 | ||
521 | @item SS format: <insn> D1(R1,B1),D2(B3),R3 | |
522 | @verbatim | |
523 | +--------+----+----+----+-------------+----+------------+ | |
524 | | OpCode | R1 | R3 | B1 | D1 | B2 | D2 | | |
525 | +--------+----+----+----+-------------+----+------------+ | |
526 | 0 8 12 16 20 32 36 47 | |
527 | @end verbatim | |
528 | ||
529 | @item SSE format: <insn> D1(B1),D2(B2) | |
530 | @verbatim | |
531 | +------------------+----+-------------+----+------------+ | |
532 | | OpCode | B1 | D1 | B2 | D2 | | |
533 | +------------------+----+-------------+----+------------+ | |
534 | 0 8 12 16 20 32 36 47 | |
535 | @end verbatim | |
536 | ||
537 | @item SSF format: <insn> D1(B1),D2(B2),R3 | |
538 | @verbatim | |
539 | +--------+----+----+----+-------------+----+------------+ | |
540 | | OpCode | R3 |OpCd| B1 | D1 | B2 | D2 | | |
541 | +--------+----+----+----+-------------+----+------------+ | |
542 | 0 8 12 16 20 32 36 47 | |
543 | @end verbatim | |
544 | ||
545 | @end table | |
546 | ||
547 | For the complete list of all instruction format variants see the | |
548 | Principles of Operation manuals. | |
549 | ||
550 | @node s390 Aliases | |
551 | @subsection Instruction Aliases | |
552 | @cindex instruction aliases, s390 | |
553 | @cindex s390 instruction aliases | |
554 | ||
555 | A specific bit pattern can have multiple mnemonics, for example | |
556 | the bit pattern @samp{0xa7000000} has the mnemonics @samp{tmh} and | |
557 | @samp{tmlh}. In addition, there are a number of mnemonics recognized by | |
558 | @code{@value{AS}} that are not present in the Principles of Operation. | |
559 | These are the short forms of the branch instructions, where the condition | |
560 | code mask operand is encoded in the mnemonic. This is relevant for the | |
561 | branch instructions, the compare and branch instructions, and the | |
562 | compare and trap instructions. | |
563 | ||
564 | For the branch instructions there are 20 condition code strings that can | |
565 | be used as part of the mnemonic in place of a mask operand in the instruction | |
566 | format: | |
567 | ||
568 | @display | |
569 | @multitable @columnfractions .30 .30 | |
570 | @headitem instruction @tab short form | |
571 | @item bcr M1,R2 @tab b<m>r R2 | |
572 | @item bc M1,D2(X2,B2) @tab b<m> D2(X2,B2) | |
573 | @item brc M1,I2 @tab j<m> I2 | |
574 | @item brcl M1,I2 @tab jg<m> I2 | |
575 | @end multitable | |
576 | @end display | |
577 | ||
578 | In the mnemonic for a branch instruction the condition code string <m> | |
579 | can be any of the following: | |
580 | ||
581 | @display | |
582 | @multitable {nle} {jump on not zero / if not zeros} | |
583 | @item o @tab jump on overflow / if ones | |
584 | @item h @tab jump on A high | |
585 | @item p @tab jump on plus | |
586 | @item nle @tab jump on not low or equal | |
587 | @item l @tab jump on A low | |
588 | @item m @tab jump on minus | |
589 | @item nhe @tab jump on not high or equal | |
590 | @item lh @tab jump on low or high | |
591 | @item ne @tab jump on A not equal B | |
592 | @item nz @tab jump on not zero / if not zeros | |
593 | @item e @tab jump on A equal B | |
594 | @item z @tab jump on zero / if zeroes | |
595 | @item nlh @tab jump on not low or high | |
596 | @item he @tab jump on high or equal | |
597 | @item nl @tab jump on A not low | |
598 | @item nm @tab jump on not minus / if not mixed | |
599 | @item le @tab jump on low or equal | |
600 | @item nh @tab jump on A not high | |
601 | @item np @tab jump on not plus | |
602 | @item no @tab jump on not overflow / if not ones | |
603 | @end multitable | |
604 | @end display | |
605 | ||
606 | For the compare and branch, and compare and trap instructions there | |
607 | are 12 condition code strings that can be used as part of the mnemonic in | |
608 | place of a mask operand in the instruction format: | |
609 | ||
610 | @display | |
611 | @multitable @columnfractions .40 .40 | |
612 | @headitem instruction @tab short form | |
613 | @item crb R1,R2,M3,D4(B4) @tab crb<m> R1,R2,D4(B4) | |
614 | @item cgrb R1,R2,M3,D4(B4) @tab cgrb<m> R1,R2,D4(B4) | |
615 | @item crj R1,R2,M3,I4 @tab crj<m> R1,R2,I4 | |
616 | @item cgrj R1,R2,M3,I4 @tab cgrj<m> R1,R2,I4 | |
617 | @item cib R1,I2,M3,D4(B4) @tab cib<m> R1,I2,D4(B4) | |
618 | @item cgib R1,I2,M3,D4(B4) @tab cgib<m> R1,I2,D4(B4) | |
619 | @item cij R1,I2,M3,I4 @tab cij<m> R1,I2,I4 | |
620 | @item cgij R1,I2,M3,I4 @tab cgij<m> R1,I2,I4 | |
621 | @item crt R1,R2,M3 @tab crt<m> R1,R2 | |
622 | @item cgrt R1,R2,M3 @tab cgrt<m> R1,R2 | |
623 | @item cit R1,I2,M3 @tab cit<m> R1,I2 | |
624 | @item cgit R1,I2,M3 @tab cgit<m> R1,I2 | |
625 | @item clrb R1,R2,M3,D4(B4) @tab clrb<m> R1,R2,D4(B4) | |
626 | @item clgrb R1,R2,M3,D4(B4) @tab clgrb<m> R1,R2,D4(B4) | |
627 | @item clrj R1,R2,M3,I4 @tab clrj<m> R1,R2,I4 | |
628 | @item clgrj R1,R2,M3,I4 @tab clgrj<m> R1,R2,I4 | |
629 | @item clib R1,I2,M3,D4(B4) @tab clib<m> R1,I2,D4(B4) | |
630 | @item clgib R1,I2,M3,D4(B4) @tab clgib<m> R1,I2,D4(B4) | |
631 | @item clij R1,I2,M3,I4 @tab clij<m> R1,I2,I4 | |
632 | @item clgij R1,I2,M3,I4 @tab clgij<m> R1,I2,I4 | |
633 | @item clrt R1,R2,M3 @tab clrt<m> R1,R2 | |
634 | @item clgrt R1,R2,M3 @tab clgrt<m> R1,R2 | |
635 | @item clfit R1,I2,M3 @tab clfit<m> R1,I2 | |
636 | @item clgit R1,I2,M3 @tab clgit<m> R1,I2 | |
637 | @end multitable | |
638 | @end display | |
639 | ||
640 | In the mnemonic for a compare and branch and compare and trap instruction | |
641 | the condition code string <m> can be any of the following: | |
642 | ||
643 | @display | |
644 | @multitable {nle} {jump on not zero / if not zeros} | |
645 | @item h @tab jump on A high | |
646 | @item nle @tab jump on not low or equal | |
647 | @item l @tab jump on A low | |
648 | @item nhe @tab jump on not high or equal | |
649 | @item ne @tab jump on A not equal B | |
650 | @item lh @tab jump on low or high | |
651 | @item e @tab jump on A equal B | |
652 | @item nlh @tab jump on not low or high | |
653 | @item nl @tab jump on A not low | |
654 | @item he @tab jump on high or equal | |
655 | @item nh @tab jump on A not high | |
656 | @item le @tab jump on low or equal | |
657 | @end multitable | |
658 | @end display | |
659 | ||
660 | @node s390 Operand Modifier | |
661 | @subsection Instruction Operand Modifier | |
662 | @cindex instruction operand modifier, s390 | |
663 | @cindex s390 instruction operand modifier | |
664 | ||
665 | If a symbol modifier is attached to a symbol in an expression for an | |
666 | instruction operand field, the symbol term is replaced with a reference | |
667 | to an object in the global offset table (GOT) or the procedure linkage | |
668 | table (PLT). The following expressions are allowed: | |
669 | @samp{symbol@@modifier + constant}, | |
670 | @samp{symbol@@modifier + label + constant}, and | |
671 | @samp{symbol@@modifier - label + constant}. | |
672 | The term @samp{symbol} is the symbol that will be entered into the GOT or | |
673 | PLT, @samp{label} is a local label, and @samp{constant} is an arbitrary | |
674 | expression that the assembler can evaluate to a constant value. | |
675 | ||
676 | The term @samp{(symbol + constant1)@@modifier +/- label + constant2} | |
677 | is also accepted but a warning message is printed and the term is | |
678 | converted to @samp{symbol@@modifier +/- label + constant1 + constant2}. | |
679 | ||
680 | @table @code | |
681 | @item @@got | |
682 | @itemx @@got12 | |
683 | The @@got modifier can be used for displacement fields, 16-bit immediate | |
684 | fields and 32-bit pc-relative immediate fields. The @@got12 modifier is | |
685 | synonym to @@got. The symbol is added to the GOT. For displacement | |
686 | fields and 16-bit immediate fields the symbol term is replaced with | |
687 | the offset from the start of the GOT to the GOT slot for the symbol. | |
688 | For a 32-bit pc-relative field the pc-relative offset to the GOT | |
689 | slot from the current instruction address is used. | |
690 | @item @@gotent | |
691 | The @@gotent modifier can be used for 32-bit pc-relative immediate fields. | |
692 | The symbol is added to the GOT and the symbol term is replaced with | |
693 | the pc-relative offset from the current instruction to the GOT slot for the | |
694 | symbol. | |
695 | @item @@gotoff | |
696 | The @@gotoff modifier can be used for 16-bit immediate fields. The symbol | |
34bca508 | 697 | term is replaced with the offset from the start of the GOT to the |
11c19e16 MS |
698 | address of the symbol. |
699 | @item @@gotplt | |
700 | The @@gotplt modifier can be used for displacement fields, 16-bit immediate | |
701 | fields, and 32-bit pc-relative immediate fields. A procedure linkage | |
702 | table entry is generated for the symbol and a jump slot for the symbol | |
703 | is added to the GOT. For displacement fields and 16-bit immediate | |
704 | fields the symbol term is replaced with the offset from the start of the | |
705 | GOT to the jump slot for the symbol. For a 32-bit pc-relative field | |
706 | the pc-relative offset to the jump slot from the current instruction | |
707 | address is used. | |
708 | @item @@plt | |
709 | The @@plt modifier can be used for 16-bit and 32-bit pc-relative immediate | |
710 | fields. A procedure linkage table entry is generated for the symbol. | |
711 | The symbol term is replaced with the relative offset from the current | |
712 | instruction to the PLT entry for the symbol. | |
713 | @item @@pltoff | |
714 | The @@pltoff modifier can be used for 16-bit immediate fields. The symbol | |
715 | term is replaced with the offset from the start of the PLT to the address | |
716 | of the symbol. | |
717 | @item @@gotntpoff | |
718 | The @@gotntpoff modifier can be used for displacement fields. The symbol | |
719 | is added to the static TLS block and the negated offset to the symbol | |
720 | in the static TLS block is added to the GOT. The symbol term is replaced | |
34bca508 | 721 | with the offset to the GOT slot from the start of the GOT. |
11c19e16 MS |
722 | @item @@indntpoff |
723 | The @@indntpoff modifier can be used for 32-bit pc-relative immediate | |
724 | fields. The symbol is added to the static TLS block and the negated offset | |
725 | to the symbol in the static TLS block is added to the GOT. The symbol term | |
726 | is replaced with the pc-relative offset to the GOT slot from the current | |
727 | instruction address. | |
728 | @end table | |
729 | ||
730 | For more information about the thread local storage modifiers | |
731 | @samp{gotntpoff} and @samp{indntpoff} see the ELF extension documentation | |
732 | @samp{ELF Handling For Thread-Local Storage}. | |
733 | ||
734 | @node s390 Instruction Marker | |
735 | @subsection Instruction Marker | |
736 | @cindex instruction marker, s390 | |
737 | @cindex s390 instruction marker | |
738 | ||
739 | The thread local storage instruction markers are used by the linker to | |
740 | perform code optimization. | |
741 | ||
742 | @table @code | |
743 | @item :tls_load | |
744 | The :tls_load marker is used to flag the load instruction in the initial | |
745 | exec TLS model that retrieves the offset from the thread pointer to a | |
34bca508 | 746 | thread local storage variable from the GOT. |
11c19e16 MS |
747 | @item :tls_gdcall |
748 | The :tls_gdcall marker is used to flag the branch-and-save instruction to | |
749 | the __tls_get_offset function in the global dynamic TLS model. | |
750 | @item :tls_ldcall | |
751 | The :tls_ldcall marker is used to flag the branch-and-save instruction to | |
752 | the __tls_get_offset function in the local dynamic TLS model. | |
753 | @end table | |
754 | ||
755 | For more information about the thread local storage instruction marker | |
756 | and the linker optimizations see the ELF extension documentation | |
757 | @samp{ELF Handling For Thread-Local Storage}. | |
758 | ||
759 | @node s390 Literal Pool Entries | |
760 | @subsection Literal Pool Entries | |
761 | @cindex literal pool entries, s390 | |
762 | @cindex s390 literal pool entries | |
763 | ||
764 | A literal pool is a collection of values. To access the values a pointer | |
765 | to the literal pool is loaded to a register, the literal pool register. | |
766 | Usually, register %r13 is used as the literal pool register | |
767 | (@ref{s390 Register}). Literal pool entries are created by adding the | |
768 | suffix :lit1, :lit2, :lit4, or :lit8 to the end of an expression for an | |
769 | instruction operand. The expression is added to the literal pool and the | |
770 | operand is replaced with the offset to the literal in the literal pool. | |
771 | ||
772 | @table @code | |
773 | @item :lit1 | |
774 | The literal pool entry is created as an 8-bit value. An operand modifier | |
775 | must not be used for the original expression. | |
776 | @item :lit2 | |
777 | The literal pool entry is created as a 16 bit value. The operand modifier | |
778 | @@got may be used in the original expression. The term @samp{x@@got:lit2} | |
779 | will put the got offset for the global symbol x to the literal pool as | |
780 | 16 bit value. | |
781 | @item :lit4 | |
782 | The literal pool entry is created as a 32-bit value. The operand modifier | |
783 | @@got and @@plt may be used in the original expression. The term | |
784 | @samp{x@@got:lit4} will put the got offset for the global symbol x to the | |
785 | literal pool as a 32-bit value. The term @samp{x@@plt:lit4} will put the | |
786 | plt offset for the global symbol x to the literal pool as a 32-bit value. | |
787 | @item :lit8 | |
788 | The literal pool entry is created as a 64-bit value. The operand modifier | |
789 | @@got and @@plt may be used in the original expression. The term | |
790 | @samp{x@@got:lit8} will put the got offset for the global symbol x to the | |
791 | literal pool as a 64-bit value. The term @samp{x@@plt:lit8} will put the | |
792 | plt offset for the global symbol x to the literal pool as a 64-bit value. | |
793 | @end table | |
794 | ||
795 | The assembler directive @samp{.ltorg} is used to emit all literal pool | |
796 | entries to the current position. | |
797 | ||
798 | @node s390 Directives | |
799 | @section Assembler Directives | |
800 | ||
34bca508 | 801 | @code{@value{AS}} for s390 supports all of the standard ELF |
11c19e16 MS |
802 | assembler directives as outlined in the main part of this document. |
803 | Some directives have been extended and there are some additional | |
804 | directives, which are only available for the s390 @code{@value{AS}}. | |
805 | ||
806 | @table @code | |
807 | @cindex @code{.insn} directive, s390 | |
808 | @item .insn | |
809 | This directive permits the numeric representation of an instructions | |
810 | and makes the assembler insert the operands according to one of the | |
811 | instructions formats for @samp{.insn} (@ref{s390 Formats}). | |
812 | For example, the instruction @samp{l %r1,24(%r15)} could be written as | |
813 | @samp{.insn rx,0x58000000,%r1,24(%r15)}. | |
814 | @cindex @code{.short} directive, s390 | |
815 | @cindex @code{.long} directive, s390 | |
816 | @cindex @code{.quad} directive, s390 | |
817 | @item .short | |
818 | @itemx .long | |
819 | @itemx .quad | |
820 | This directive places one or more 16-bit (.short), 32-bit (.long), or | |
821 | 64-bit (.quad) values into the current section. If an ELF or TLS modifier | |
34bca508 | 822 | is used only the following expressions are allowed: |
11c19e16 MS |
823 | @samp{symbol@@modifier + constant}, |
824 | @samp{symbol@@modifier + label + constant}, and | |
825 | @samp{symbol@@modifier - label + constant}. | |
826 | The following modifiers are available: | |
827 | @table @code | |
828 | @item @@got | |
829 | @itemx @@got12 | |
830 | The @@got modifier can be used for .short, .long and .quad. The @@got12 | |
831 | modifier is synonym to @@got. The symbol is added to the GOT. The symbol | |
832 | term is replaced with offset from the start of the GOT to the GOT slot for | |
833 | the symbol. | |
834 | @item @@gotoff | |
835 | The @@gotoff modifier can be used for .short, .long and .quad. The symbol | |
836 | term is replaced with the offset from the start of the GOT to the address | |
837 | of the symbol. | |
838 | @item @@gotplt | |
839 | The @@gotplt modifier can be used for .long and .quad. A procedure linkage | |
840 | table entry is generated for the symbol and a jump slot for the symbol | |
841 | is added to the GOT. The symbol term is replaced with the offset from the | |
842 | start of the GOT to the jump slot for the symbol. | |
843 | @item @@plt | |
844 | The @@plt modifier can be used for .long and .quad. A procedure linkage | |
845 | table entry us generated for the symbol. The symbol term is replaced with | |
846 | the address of the PLT entry for the symbol. | |
847 | @item @@pltoff | |
848 | The @@pltoff modifier can be used for .short, .long and .quad. The symbol | |
849 | term is replaced with the offset from the start of the PLT to the address | |
850 | of the symbol. | |
851 | @item @@tlsgd | |
852 | @itemx @@tlsldm | |
853 | The @@tlsgd and @@tlsldm modifier can be used for .long and .quad. A | |
854 | tls_index structure for the symbol is added to the GOT. The symbol term is | |
855 | replaced with the offset from the start of the GOT to the tls_index structure. | |
856 | @item @@gotntpoff | |
857 | @itemx @@indntpoff | |
858 | The @@gotntpoff and @@indntpoff modifier can be used for .long and .quad. | |
859 | The symbol is added to the static TLS block and the negated offset to the | |
860 | symbol in the static TLS block is added to the GOT. For @@gotntpoff the | |
861 | symbol term is replaced with the offset from the start of the GOT to the | |
862 | GOT slot, for @@indntpoff the symbol term is replaced with the address | |
863 | of the GOT slot. | |
864 | @item @@dtpoff | |
865 | The @@dtpoff modifier can be used for .long and .quad. The symbol term | |
866 | is replaced with the offset of the symbol relative to the start of the | |
867 | TLS block it is contained in. | |
868 | @item @@ntpoff | |
869 | The @@ntpoff modifier can be used for .long and .quad. The symbol term | |
870 | is replaced with the offset of the symbol relative to the TCB pointer. | |
871 | @end table | |
872 | ||
873 | For more information about the thread local storage modifiers see the | |
874 | ELF extension documentation @samp{ELF Handling For Thread-Local Storage}. | |
875 | ||
876 | @cindex @code{.ltorg} directive, s390 | |
877 | @item .ltorg | |
878 | This directive causes the current contents of the literal pool to be | |
879 | dumped to the current location (@ref{s390 Literal Pool Entries}). | |
902cc293 AK |
880 | |
881 | @cindex @code{.machine} directive, s390 | |
7ecc513a DV |
882 | @item .machine @var{STRING}[+@var{EXTENSION}]@dots{} |
883 | ||
884 | This directive allows changing the machine for which code is | |
885 | generated. @code{string} may be any of the @code{-march=} | |
886 | selection options, or @code{push}, or @code{pop}. @code{.machine | |
887 | push} saves the currently selected cpu, which may be restored with | |
888 | @code{.machine pop}. Be aware that the cpu string has to be put | |
889 | into double quotes in case it contains characters not appropriate | |
890 | for identifiers. So you have to write @code{"z9-109"} instead of | |
891 | just @code{z9-109}. Extensions can be specified after the cpu | |
33eaf5de | 892 | name, separated by plus characters. Valid extensions are: |
7ecc513a DV |
893 | @code{htm}, |
894 | @code{nohtm}, | |
895 | @code{vx}, | |
896 | @code{novx}. | |
897 | They extend the basic instruction set with features from a higher | |
898 | cpu level, or remove support for a feature from the given cpu | |
899 | level. | |
900 | ||
901 | Example: @code{z13+nohtm} allows all instructions of the z13 cpu | |
902 | except instructions from the HTM facility. | |
1dd53816 AK |
903 | |
904 | @cindex @code{.machinemode} directive, s390 | |
905 | @item .machinemode string | |
906 | This directive allows to change the architecture mode for which code | |
907 | is being generated. @code{string} may be @code{esa}, @code{zarch}, | |
908 | @code{zarch_nohighgprs}, @code{push}, or @code{pop}. | |
909 | @code{.machinemode zarch_nohighgprs} can be used to prevent the | |
910 | @code{highgprs} flag from being set in the ELF header of the output | |
911 | file. This is useful in situations where the code is gated with a | |
912 | runtime check which makes sure that the code is only executed on | |
913 | kernels providing the @code{highgprs} feature. | |
914 | @code{.machinemode push} saves the currently selected mode, which may | |
915 | be restored with @code{.machinemode pop}. | |
11c19e16 MS |
916 | @end table |
917 | ||
918 | @node s390 Floating Point | |
919 | @section Floating Point | |
920 | @cindex floating point, s390 | |
921 | @cindex s390 floating point | |
922 | ||
923 | The assembler recognizes both the @sc{ieee} floating-point instruction and | |
924 | the hexadecimal floating-point instructions. The floating-point constructors | |
925 | @samp{.float}, @samp{.single}, and @samp{.double} always emit the | |
926 | @sc{ieee} format. To assemble hexadecimal floating-point constants the | |
927 | @samp{.long} and @samp{.quad} directives must be used. |