Commit | Line | Data |
---|---|---|
4a25e418 NI |
1 | /* |
2 | * sh7760fb.h -- platform data for SH7760/SH7763 LCDC framebuffer driver. | |
3 | * | |
4 | * (c) 2006-2008 MSC Vertriebsges.m.b.H., | |
5 | * Manuel Lauss <mano@roarinelk.homelinux.net> | |
6 | * (c) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> | |
7 | */ | |
8 | ||
9 | #ifndef _ASM_SH_SH7760FB_H | |
10 | #define _ASM_SH_SH7760FB_H | |
11 | ||
12 | /* | |
13 | * some bits of the colormap registers should be written as zero. | |
14 | * create a mask for that. | |
15 | */ | |
16 | #define SH7760FB_PALETTE_MASK 0x00f8fcf8 | |
17 | ||
18 | /* The LCDC dma engine always sets bits 27-26 to 1: this is Area3 */ | |
19 | #define SH7760FB_DMA_MASK 0x0C000000 | |
20 | ||
21 | /* palette */ | |
22 | #define LDPR(x) (((x) << 2)) | |
23 | ||
24 | /* framebuffer registers and bits */ | |
25 | #define LDICKR 0x400 | |
26 | #define LDMTR 0x402 | |
27 | /* see sh7760fb.h for LDMTR bits */ | |
28 | #define LDDFR 0x404 | |
29 | #define LDDFR_PABD (1 << 8) | |
30 | #define LDDFR_COLOR_MASK 0x7F | |
31 | #define LDSMR 0x406 | |
32 | #define LDSMR_ROT (1 << 13) | |
33 | #define LDSARU 0x408 | |
34 | #define LDSARL 0x40c | |
35 | #define LDLAOR 0x410 | |
36 | #define LDPALCR 0x412 | |
37 | #define LDPALCR_PALS (1 << 4) | |
38 | #define LDPALCR_PALEN (1 << 0) | |
39 | #define LDHCNR 0x414 | |
40 | #define LDHSYNR 0x416 | |
41 | #define LDVDLNR 0x418 | |
42 | #define LDVTLNR 0x41a | |
43 | #define LDVSYNR 0x41c | |
44 | #define LDACLNR 0x41e | |
45 | #define LDINTR 0x420 | |
46 | #define LDPMMR 0x424 | |
47 | #define LDPSPR 0x426 | |
48 | #define LDCNTR 0x428 | |
49 | #define LDCNTR_DON (1 << 0) | |
50 | #define LDCNTR_DON2 (1 << 4) | |
51 | ||
52 | #ifdef CONFIG_CPU_SUBTYPE_SH7763 | |
53 | # define LDLIRNR 0x440 | |
54 | /* LDINTR bit */ | |
55 | # define LDINTR_MINTEN (1 << 15) | |
56 | # define LDINTR_FINTEN (1 << 14) | |
57 | # define LDINTR_VSINTEN (1 << 13) | |
58 | # define LDINTR_VEINTEN (1 << 12) | |
59 | # define LDINTR_MINTS (1 << 11) | |
60 | # define LDINTR_FINTS (1 << 10) | |
61 | # define LDINTR_VSINTS (1 << 9) | |
62 | # define LDINTR_VEINTS (1 << 8) | |
63 | # define VINT_START (LDINTR_VSINTEN) | |
64 | # define VINT_CHECK (LDINTR_VSINTS) | |
65 | #else | |
66 | /* LDINTR bit */ | |
67 | # define LDINTR_VINTSEL (1 << 12) | |
68 | # define LDINTR_VINTE (1 << 8) | |
69 | # define LDINTR_VINTS (1 << 0) | |
70 | # define VINT_START (LDINTR_VINTSEL) | |
71 | # define VINT_CHECK (LDINTR_VINTS) | |
72 | #endif | |
73 | ||
74 | /* HSYNC polarity inversion */ | |
75 | #define LDMTR_FLMPOL (1 << 15) | |
76 | ||
77 | /* VSYNC polarity inversion */ | |
78 | #define LDMTR_CL1POL (1 << 14) | |
79 | ||
80 | /* DISPLAY-ENABLE polarity inversion */ | |
81 | #define LDMTR_DISPEN_LOWACT (1 << 13) | |
82 | ||
83 | /* DISPLAY DATA BUS polarity inversion */ | |
84 | #define LDMTR_DPOL_LOWACT (1 << 12) | |
85 | ||
86 | /* AC modulation signal enable */ | |
87 | #define LDMTR_MCNT (1 << 10) | |
88 | ||
89 | /* Disable output of HSYNC during VSYNC period */ | |
90 | #define LDMTR_CL1CNT (1 << 9) | |
91 | ||
92 | /* Disable output of VSYNC during VSYNC period */ | |
93 | #define LDMTR_CL2CNT (1 << 8) | |
94 | ||
95 | /* Display types supported by the LCDC */ | |
96 | #define LDMTR_STN_MONO_4 0x00 | |
97 | #define LDMTR_STN_MONO_8 0x01 | |
98 | #define LDMTR_STN_COLOR_4 0x08 | |
99 | #define LDMTR_STN_COLOR_8 0x09 | |
100 | #define LDMTR_STN_COLOR_12 0x0A | |
101 | #define LDMTR_STN_COLOR_16 0x0B | |
102 | #define LDMTR_DSTN_MONO_8 0x11 | |
103 | #define LDMTR_DSTN_MONO_16 0x13 | |
104 | #define LDMTR_DSTN_COLOR_8 0x19 | |
105 | #define LDMTR_DSTN_COLOR_12 0x1A | |
106 | #define LDMTR_DSTN_COLOR_16 0x1B | |
107 | #define LDMTR_TFT_COLOR_16 0x2B | |
108 | ||
109 | /* framebuffer color layout */ | |
110 | #define LDDFR_1BPP_MONO 0x00 | |
111 | #define LDDFR_2BPP_MONO 0x01 | |
112 | #define LDDFR_4BPP_MONO 0x02 | |
113 | #define LDDFR_6BPP_MONO 0x04 | |
114 | #define LDDFR_4BPP 0x0A | |
115 | #define LDDFR_8BPP 0x0C | |
116 | #define LDDFR_16BPP_RGB555 0x1D | |
117 | #define LDDFR_16BPP_RGB565 0x2D | |
118 | ||
119 | /* LCDC Pixclock sources */ | |
120 | #define LCDC_CLKSRC_BUSCLOCK 0 | |
121 | #define LCDC_CLKSRC_PERIPHERAL 1 | |
122 | #define LCDC_CLKSRC_EXTERNAL 2 | |
123 | ||
124 | #define LDICKR_CLKSRC(x) \ | |
125 | (((x) & 3) << 12) | |
126 | ||
127 | /* LCDC pixclock input divider. Set to 1 at a minimum! */ | |
128 | #define LDICKR_CLKDIV(x) \ | |
129 | ((x) & 0x1f) | |
130 | ||
131 | struct sh7760fb_platdata { | |
132 | ||
133 | /* Set this member to a valid fb_videmode for the display you | |
134 | * wish to use. The following members must be initialized: | |
135 | * xres, yres, hsync_len, vsync_len, sync, | |
136 | * {left,right,upper,lower}_margin. | |
137 | * The driver uses the above members to calculate register values | |
138 | * and memory requirements. Other members are ignored but may | |
139 | * be used by other framebuffer layer components. | |
140 | */ | |
141 | struct fb_videomode *def_mode; | |
142 | ||
143 | /* LDMTR includes display type and signal polarity. The | |
144 | * HSYNC/VSYNC polarities are derived from the fb_var_screeninfo | |
145 | * data above; however the polarities of the following signals | |
146 | * must be encoded in the ldmtr member: | |
147 | * Display Enable signal (default high-active) DISPEN_LOWACT | |
148 | * Display Data signals (default high-active) DPOL_LOWACT | |
149 | * AC Modulation signal (default off) MCNT | |
150 | * Hsync-During-Vsync suppression (default off) CL1CNT | |
151 | * Vsync-during-vsync suppression (default off) CL2CNT | |
152 | * NOTE: also set a display type! | |
153 | * (one of LDMTR_{STN,DSTN,TFT}_{MONO,COLOR}_{4,8,12,16}) | |
154 | */ | |
155 | u16 ldmtr; | |
156 | ||
157 | /* LDDFR controls framebuffer image format (depth, organization) | |
158 | * Use ONE of the LDDFR_?BPP_* macros! | |
159 | */ | |
160 | u16 lddfr; | |
161 | ||
162 | /* LDPMMR and LDPSPR control the timing of the power signals | |
163 | * for the display. Please read the SH7760 Hardware Manual, | |
164 | * Chapters 30.3.17, 30.3.18 and 30.4.6! | |
165 | */ | |
166 | u16 ldpmmr; | |
167 | u16 ldpspr; | |
168 | ||
169 | /* LDACLNR contains the line numbers after which the AC modulation | |
170 | * signal is to toggle. Set to ZERO for TFTs or displays which | |
171 | * do not need it. (Chapter 30.3.15 in SH7760 Hardware Manual). | |
172 | */ | |
173 | u16 ldaclnr; | |
174 | ||
175 | /* LDICKR contains information on pixelclock source and config. | |
176 | * Please use the LDICKR_CLKSRC() and LDICKR_CLKDIV() macros. | |
177 | * minimal value for CLKDIV() must be 1!. | |
178 | */ | |
179 | u16 ldickr; | |
180 | ||
181 | /* set this member to 1 if you wish to use the LCDC's hardware | |
182 | * rotation function. This is limited to displays <= 320x200 | |
183 | * pixels resolution! | |
184 | */ | |
185 | int rotate; /* set to 1 to rotate 90 CCW */ | |
186 | ||
187 | /* set this to 1 to suppress vsync irq use. */ | |
188 | int novsync; | |
189 | ||
190 | /* blanking hook for platform. Set this if your platform can do | |
191 | * more than the LCDC in terms of blanking (e.g. disable clock | |
192 | * generator / backlight power supply / etc. | |
193 | */ | |
194 | void (*blank) (int); | |
195 | }; | |
196 | ||
197 | #endif /* _ASM_SH_SH7760FB_H */ |