Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * ethtool.h: Defines for Linux ethtool. | |
3 | * | |
4 | * Copyright (C) 1998 David S. Miller (davem@redhat.com) | |
5 | * Copyright 2001 Jeff Garzik <jgarzik@pobox.com> | |
6 | * Portions Copyright 2001 Sun Microsystems (thockin@sun.com) | |
7 | * Portions Copyright 2002 Intel (eli.kupermann@intel.com, | |
8 | * christopher.leech@intel.com, | |
9 | * scott.feldman@intel.com) | |
10 | */ | |
11 | ||
12 | #ifndef _LINUX_ETHTOOL_H | |
13 | #define _LINUX_ETHTOOL_H | |
14 | ||
15 | ||
16 | /* This should work for both 32 and 64 bit userland. */ | |
17 | struct ethtool_cmd { | |
c3ce7e20 DW |
18 | __u32 cmd; |
19 | __u32 supported; /* Features this interface supports */ | |
20 | __u32 advertising; /* Features this interface advertises */ | |
21 | __u16 speed; /* The forced speed, 10Mb, 100Mb, gigabit */ | |
22 | __u8 duplex; /* Duplex, half or full */ | |
23 | __u8 port; /* Which connector port */ | |
24 | __u8 phy_address; | |
25 | __u8 transceiver; /* Which transceiver to use */ | |
26 | __u8 autoneg; /* Enable or disable autonegotiation */ | |
27 | __u32 maxtxpkt; /* Tx pkts before generating tx int */ | |
28 | __u32 maxrxpkt; /* Rx pkts before generating rx int */ | |
29 | __u32 reserved[4]; | |
1da177e4 LT |
30 | }; |
31 | ||
32 | #define ETHTOOL_BUSINFO_LEN 32 | |
33 | /* these strings are set to whatever the driver author decides... */ | |
34 | struct ethtool_drvinfo { | |
c3ce7e20 | 35 | __u32 cmd; |
1da177e4 LT |
36 | char driver[32]; /* driver short name, "tulip", "eepro100" */ |
37 | char version[32]; /* driver version string */ | |
38 | char fw_version[32]; /* firmware version string, if applicable */ | |
39 | char bus_info[ETHTOOL_BUSINFO_LEN]; /* Bus info for this IF. */ | |
40 | /* For PCI devices, use pci_name(pci_dev). */ | |
41 | char reserved1[32]; | |
339bf024 JG |
42 | char reserved2[12]; |
43 | __u32 n_priv_flags; /* number of flags valid in ETHTOOL_GPFLAGS */ | |
c3ce7e20 DW |
44 | __u32 n_stats; /* number of u64's from ETHTOOL_GSTATS */ |
45 | __u32 testinfo_len; | |
46 | __u32 eedump_len; /* Size of data from ETHTOOL_GEEPROM (bytes) */ | |
47 | __u32 regdump_len; /* Size of data from ETHTOOL_GREGS (bytes) */ | |
1da177e4 LT |
48 | }; |
49 | ||
50 | #define SOPASS_MAX 6 | |
51 | /* wake-on-lan settings */ | |
52 | struct ethtool_wolinfo { | |
c3ce7e20 DW |
53 | __u32 cmd; |
54 | __u32 supported; | |
55 | __u32 wolopts; | |
56 | __u8 sopass[SOPASS_MAX]; /* SecureOn(tm) password */ | |
1da177e4 LT |
57 | }; |
58 | ||
59 | /* for passing single values */ | |
60 | struct ethtool_value { | |
c3ce7e20 DW |
61 | __u32 cmd; |
62 | __u32 data; | |
1da177e4 LT |
63 | }; |
64 | ||
65 | /* for passing big chunks of data */ | |
66 | struct ethtool_regs { | |
c3ce7e20 DW |
67 | __u32 cmd; |
68 | __u32 version; /* driver-specific, indicates different chips/revs */ | |
69 | __u32 len; /* bytes */ | |
70 | __u8 data[0]; | |
1da177e4 LT |
71 | }; |
72 | ||
73 | /* for passing EEPROM chunks */ | |
74 | struct ethtool_eeprom { | |
c3ce7e20 DW |
75 | __u32 cmd; |
76 | __u32 magic; | |
77 | __u32 offset; /* in bytes */ | |
78 | __u32 len; /* in bytes */ | |
79 | __u8 data[0]; | |
1da177e4 LT |
80 | }; |
81 | ||
82 | /* for configuring coalescing parameters of chip */ | |
83 | struct ethtool_coalesce { | |
c3ce7e20 | 84 | __u32 cmd; /* ETHTOOL_{G,S}COALESCE */ |
1da177e4 LT |
85 | |
86 | /* How many usecs to delay an RX interrupt after | |
87 | * a packet arrives. If 0, only rx_max_coalesced_frames | |
88 | * is used. | |
89 | */ | |
c3ce7e20 | 90 | __u32 rx_coalesce_usecs; |
1da177e4 LT |
91 | |
92 | /* How many packets to delay an RX interrupt after | |
93 | * a packet arrives. If 0, only rx_coalesce_usecs is | |
94 | * used. It is illegal to set both usecs and max frames | |
95 | * to zero as this would cause RX interrupts to never be | |
96 | * generated. | |
97 | */ | |
c3ce7e20 | 98 | __u32 rx_max_coalesced_frames; |
1da177e4 LT |
99 | |
100 | /* Same as above two parameters, except that these values | |
101 | * apply while an IRQ is being serviced by the host. Not | |
102 | * all cards support this feature and the values are ignored | |
103 | * in that case. | |
104 | */ | |
c3ce7e20 DW |
105 | __u32 rx_coalesce_usecs_irq; |
106 | __u32 rx_max_coalesced_frames_irq; | |
1da177e4 LT |
107 | |
108 | /* How many usecs to delay a TX interrupt after | |
109 | * a packet is sent. If 0, only tx_max_coalesced_frames | |
110 | * is used. | |
111 | */ | |
c3ce7e20 | 112 | __u32 tx_coalesce_usecs; |
1da177e4 LT |
113 | |
114 | /* How many packets to delay a TX interrupt after | |
115 | * a packet is sent. If 0, only tx_coalesce_usecs is | |
116 | * used. It is illegal to set both usecs and max frames | |
117 | * to zero as this would cause TX interrupts to never be | |
118 | * generated. | |
119 | */ | |
c3ce7e20 | 120 | __u32 tx_max_coalesced_frames; |
1da177e4 LT |
121 | |
122 | /* Same as above two parameters, except that these values | |
123 | * apply while an IRQ is being serviced by the host. Not | |
124 | * all cards support this feature and the values are ignored | |
125 | * in that case. | |
126 | */ | |
c3ce7e20 DW |
127 | __u32 tx_coalesce_usecs_irq; |
128 | __u32 tx_max_coalesced_frames_irq; | |
1da177e4 LT |
129 | |
130 | /* How many usecs to delay in-memory statistics | |
131 | * block updates. Some drivers do not have an in-memory | |
132 | * statistic block, and in such cases this value is ignored. | |
133 | * This value must not be zero. | |
134 | */ | |
c3ce7e20 | 135 | __u32 stats_block_coalesce_usecs; |
1da177e4 LT |
136 | |
137 | /* Adaptive RX/TX coalescing is an algorithm implemented by | |
138 | * some drivers to improve latency under low packet rates and | |
139 | * improve throughput under high packet rates. Some drivers | |
140 | * only implement one of RX or TX adaptive coalescing. Anything | |
141 | * not implemented by the driver causes these values to be | |
142 | * silently ignored. | |
143 | */ | |
c3ce7e20 DW |
144 | __u32 use_adaptive_rx_coalesce; |
145 | __u32 use_adaptive_tx_coalesce; | |
1da177e4 LT |
146 | |
147 | /* When the packet rate (measured in packets per second) | |
148 | * is below pkt_rate_low, the {rx,tx}_*_low parameters are | |
149 | * used. | |
150 | */ | |
c3ce7e20 DW |
151 | __u32 pkt_rate_low; |
152 | __u32 rx_coalesce_usecs_low; | |
153 | __u32 rx_max_coalesced_frames_low; | |
154 | __u32 tx_coalesce_usecs_low; | |
155 | __u32 tx_max_coalesced_frames_low; | |
1da177e4 LT |
156 | |
157 | /* When the packet rate is below pkt_rate_high but above | |
158 | * pkt_rate_low (both measured in packets per second) the | |
159 | * normal {rx,tx}_* coalescing parameters are used. | |
160 | */ | |
161 | ||
162 | /* When the packet rate is (measured in packets per second) | |
163 | * is above pkt_rate_high, the {rx,tx}_*_high parameters are | |
164 | * used. | |
165 | */ | |
c3ce7e20 DW |
166 | __u32 pkt_rate_high; |
167 | __u32 rx_coalesce_usecs_high; | |
168 | __u32 rx_max_coalesced_frames_high; | |
169 | __u32 tx_coalesce_usecs_high; | |
170 | __u32 tx_max_coalesced_frames_high; | |
1da177e4 LT |
171 | |
172 | /* How often to do adaptive coalescing packet rate sampling, | |
173 | * measured in seconds. Must not be zero. | |
174 | */ | |
c3ce7e20 | 175 | __u32 rate_sample_interval; |
1da177e4 LT |
176 | }; |
177 | ||
178 | /* for configuring RX/TX ring parameters */ | |
179 | struct ethtool_ringparam { | |
c3ce7e20 | 180 | __u32 cmd; /* ETHTOOL_{G,S}RINGPARAM */ |
1da177e4 LT |
181 | |
182 | /* Read only attributes. These indicate the maximum number | |
183 | * of pending RX/TX ring entries the driver will allow the | |
184 | * user to set. | |
185 | */ | |
c3ce7e20 DW |
186 | __u32 rx_max_pending; |
187 | __u32 rx_mini_max_pending; | |
188 | __u32 rx_jumbo_max_pending; | |
189 | __u32 tx_max_pending; | |
1da177e4 LT |
190 | |
191 | /* Values changeable by the user. The valid values are | |
192 | * in the range 1 to the "*_max_pending" counterpart above. | |
193 | */ | |
c3ce7e20 DW |
194 | __u32 rx_pending; |
195 | __u32 rx_mini_pending; | |
196 | __u32 rx_jumbo_pending; | |
197 | __u32 tx_pending; | |
1da177e4 LT |
198 | }; |
199 | ||
200 | /* for configuring link flow control parameters */ | |
201 | struct ethtool_pauseparam { | |
c3ce7e20 | 202 | __u32 cmd; /* ETHTOOL_{G,S}PAUSEPARAM */ |
1da177e4 LT |
203 | |
204 | /* If the link is being auto-negotiated (via ethtool_cmd.autoneg | |
205 | * being true) the user may set 'autonet' here non-zero to have the | |
206 | * pause parameters be auto-negotiated too. In such a case, the | |
207 | * {rx,tx}_pause values below determine what capabilities are | |
208 | * advertised. | |
209 | * | |
210 | * If 'autoneg' is zero or the link is not being auto-negotiated, | |
211 | * then {rx,tx}_pause force the driver to use/not-use pause | |
212 | * flow control. | |
213 | */ | |
c3ce7e20 DW |
214 | __u32 autoneg; |
215 | __u32 rx_pause; | |
216 | __u32 tx_pause; | |
1da177e4 LT |
217 | }; |
218 | ||
219 | #define ETH_GSTRING_LEN 32 | |
220 | enum ethtool_stringset { | |
221 | ETH_SS_TEST = 0, | |
222 | ETH_SS_STATS, | |
339bf024 | 223 | ETH_SS_PRIV_FLAGS, |
1da177e4 LT |
224 | }; |
225 | ||
226 | /* for passing string sets for data tagging */ | |
227 | struct ethtool_gstrings { | |
c3ce7e20 DW |
228 | __u32 cmd; /* ETHTOOL_GSTRINGS */ |
229 | __u32 string_set; /* string set id e.c. ETH_SS_TEST, etc*/ | |
230 | __u32 len; /* number of strings in the string set */ | |
231 | __u8 data[0]; | |
1da177e4 LT |
232 | }; |
233 | ||
234 | enum ethtool_test_flags { | |
235 | ETH_TEST_FL_OFFLINE = (1 << 0), /* online / offline */ | |
236 | ETH_TEST_FL_FAILED = (1 << 1), /* test passed / failed */ | |
237 | }; | |
238 | ||
239 | /* for requesting NIC test and getting results*/ | |
240 | struct ethtool_test { | |
c3ce7e20 DW |
241 | __u32 cmd; /* ETHTOOL_TEST */ |
242 | __u32 flags; /* ETH_TEST_FL_xxx */ | |
243 | __u32 reserved; | |
244 | __u32 len; /* result length, in number of u64 elements */ | |
245 | __u64 data[0]; | |
1da177e4 LT |
246 | }; |
247 | ||
248 | /* for dumping NIC-specific statistics */ | |
249 | struct ethtool_stats { | |
c3ce7e20 DW |
250 | __u32 cmd; /* ETHTOOL_GSTATS */ |
251 | __u32 n_stats; /* number of u64's being returned */ | |
252 | __u64 data[0]; | |
1da177e4 LT |
253 | }; |
254 | ||
a6f9a705 | 255 | struct ethtool_perm_addr { |
c3ce7e20 DW |
256 | __u32 cmd; /* ETHTOOL_GPERMADDR */ |
257 | __u32 size; | |
258 | __u8 data[0]; | |
a6f9a705 JW |
259 | }; |
260 | ||
3ae7c0b2 JG |
261 | /* boolean flags controlling per-interface behavior characteristics. |
262 | * When reading, the flag indicates whether or not a certain behavior | |
263 | * is enabled/present. When writing, the flag indicates whether | |
264 | * or not the driver should turn on (set) or off (clear) a behavior. | |
265 | * | |
266 | * Some behaviors may read-only (unconditionally absent or present). | |
267 | * If such is the case, return EINVAL in the set-flags operation if the | |
268 | * flag differs from the read-only value. | |
269 | */ | |
270 | enum ethtool_flags { | |
271 | ETH_FLAG_LRO = (1 << 15), /* LRO is enabled */ | |
272 | }; | |
273 | ||
c3ce7e20 DW |
274 | #ifdef __KERNEL__ |
275 | ||
1da177e4 LT |
276 | struct net_device; |
277 | ||
278 | /* Some generic methods drivers may use in their ethtool_ops */ | |
279 | u32 ethtool_op_get_link(struct net_device *dev); | |
280 | u32 ethtool_op_get_tx_csum(struct net_device *dev); | |
281 | int ethtool_op_set_tx_csum(struct net_device *dev, u32 data); | |
69f6a0fa | 282 | int ethtool_op_set_tx_hw_csum(struct net_device *dev, u32 data); |
6460d948 | 283 | int ethtool_op_set_tx_ipv6_csum(struct net_device *dev, u32 data); |
1da177e4 LT |
284 | u32 ethtool_op_get_sg(struct net_device *dev); |
285 | int ethtool_op_set_sg(struct net_device *dev, u32 data); | |
286 | u32 ethtool_op_get_tso(struct net_device *dev); | |
287 | int ethtool_op_set_tso(struct net_device *dev, u32 data); | |
e89e9cf5 AR |
288 | u32 ethtool_op_get_ufo(struct net_device *dev); |
289 | int ethtool_op_set_ufo(struct net_device *dev, u32 data); | |
3ae7c0b2 JG |
290 | u32 ethtool_op_get_flags(struct net_device *dev); |
291 | int ethtool_op_set_flags(struct net_device *dev, u32 data); | |
1da177e4 LT |
292 | |
293 | /** | |
294 | * ðtool_ops - Alter and report network device settings | |
295 | * get_settings: Get device-specific settings | |
296 | * set_settings: Set device-specific settings | |
297 | * get_drvinfo: Report driver information | |
298 | * get_regs: Get device registers | |
299 | * get_wol: Report whether Wake-on-Lan is enabled | |
300 | * set_wol: Turn Wake-on-Lan on or off | |
301 | * get_msglevel: Report driver message level | |
302 | * set_msglevel: Set driver message level | |
303 | * nway_reset: Restart autonegotiation | |
304 | * get_link: Get link status | |
305 | * get_eeprom: Read data from the device EEPROM | |
306 | * set_eeprom: Write data to the device EEPROM | |
307 | * get_coalesce: Get interrupt coalescing parameters | |
308 | * set_coalesce: Set interrupt coalescing parameters | |
309 | * get_ringparam: Report ring sizes | |
310 | * set_ringparam: Set ring sizes | |
311 | * get_pauseparam: Report pause parameters | |
312 | * set_pauseparam: Set pause paramters | |
313 | * get_rx_csum: Report whether receive checksums are turned on or off | |
314 | * set_rx_csum: Turn receive checksum on or off | |
315 | * get_tx_csum: Report whether transmit checksums are turned on or off | |
316 | * set_tx_csum: Turn transmit checksums on or off | |
317 | * get_sg: Report whether scatter-gather is enabled | |
318 | * set_sg: Turn scatter-gather on or off | |
319 | * get_tso: Report whether TCP segmentation offload is enabled | |
320 | * set_tso: Turn TCP segmentation offload on or off | |
e89e9cf5 AR |
321 | * get_ufo: Report whether UDP fragmentation offload is enabled |
322 | * set_ufo: Turn UDP fragmentation offload on or off | |
1da177e4 LT |
323 | * self_test: Run specified self-tests |
324 | * get_strings: Return a set of strings that describe the requested objects | |
325 | * phys_id: Identify the device | |
326 | * get_stats: Return statistics about the device | |
3ae7c0b2 JG |
327 | * get_flags: get 32-bit flags bitmap |
328 | * set_flags: set 32-bit flags bitmap | |
a6f9a705 | 329 | * |
1da177e4 LT |
330 | * Description: |
331 | * | |
332 | * get_settings: | |
333 | * @get_settings is passed an ðtool_cmd to fill in. It returns | |
334 | * an negative errno or zero. | |
335 | * | |
336 | * set_settings: | |
337 | * @set_settings is passed an ðtool_cmd and should attempt to set | |
338 | * all the settings this device supports. It may return an error value | |
339 | * if something goes wrong (otherwise 0). | |
340 | * | |
341 | * get_eeprom: | |
342 | * Should fill in the magic field. Don't need to check len for zero | |
343 | * or wraparound. Fill in the data argument with the eeprom values | |
344 | * from offset to offset + len. Update len to the amount read. | |
345 | * Returns an error or zero. | |
346 | * | |
347 | * set_eeprom: | |
348 | * Should validate the magic field. Don't need to check len for zero | |
349 | * or wraparound. Update len to the amount written. Returns an error | |
350 | * or zero. | |
351 | */ | |
352 | struct ethtool_ops { | |
353 | int (*get_settings)(struct net_device *, struct ethtool_cmd *); | |
354 | int (*set_settings)(struct net_device *, struct ethtool_cmd *); | |
355 | void (*get_drvinfo)(struct net_device *, struct ethtool_drvinfo *); | |
356 | int (*get_regs_len)(struct net_device *); | |
357 | void (*get_regs)(struct net_device *, struct ethtool_regs *, void *); | |
358 | void (*get_wol)(struct net_device *, struct ethtool_wolinfo *); | |
359 | int (*set_wol)(struct net_device *, struct ethtool_wolinfo *); | |
360 | u32 (*get_msglevel)(struct net_device *); | |
361 | void (*set_msglevel)(struct net_device *, u32); | |
362 | int (*nway_reset)(struct net_device *); | |
363 | u32 (*get_link)(struct net_device *); | |
364 | int (*get_eeprom_len)(struct net_device *); | |
365 | int (*get_eeprom)(struct net_device *, struct ethtool_eeprom *, u8 *); | |
366 | int (*set_eeprom)(struct net_device *, struct ethtool_eeprom *, u8 *); | |
367 | int (*get_coalesce)(struct net_device *, struct ethtool_coalesce *); | |
368 | int (*set_coalesce)(struct net_device *, struct ethtool_coalesce *); | |
369 | void (*get_ringparam)(struct net_device *, struct ethtool_ringparam *); | |
370 | int (*set_ringparam)(struct net_device *, struct ethtool_ringparam *); | |
371 | void (*get_pauseparam)(struct net_device *, struct ethtool_pauseparam*); | |
372 | int (*set_pauseparam)(struct net_device *, struct ethtool_pauseparam*); | |
373 | u32 (*get_rx_csum)(struct net_device *); | |
374 | int (*set_rx_csum)(struct net_device *, u32); | |
375 | u32 (*get_tx_csum)(struct net_device *); | |
376 | int (*set_tx_csum)(struct net_device *, u32); | |
377 | u32 (*get_sg)(struct net_device *); | |
378 | int (*set_sg)(struct net_device *, u32); | |
379 | u32 (*get_tso)(struct net_device *); | |
380 | int (*set_tso)(struct net_device *, u32); | |
1da177e4 LT |
381 | void (*self_test)(struct net_device *, struct ethtool_test *, u64 *); |
382 | void (*get_strings)(struct net_device *, u32 stringset, u8 *); | |
383 | int (*phys_id)(struct net_device *, u32); | |
1da177e4 LT |
384 | void (*get_ethtool_stats)(struct net_device *, struct ethtool_stats *, u64 *); |
385 | int (*begin)(struct net_device *); | |
386 | void (*complete)(struct net_device *); | |
e89e9cf5 AR |
387 | u32 (*get_ufo)(struct net_device *); |
388 | int (*set_ufo)(struct net_device *, u32); | |
3ae7c0b2 JG |
389 | u32 (*get_flags)(struct net_device *); |
390 | int (*set_flags)(struct net_device *, u32); | |
339bf024 JG |
391 | u32 (*get_priv_flags)(struct net_device *); |
392 | int (*set_priv_flags)(struct net_device *, u32); | |
ff03d49f JG |
393 | int (*get_sset_count)(struct net_device *, int); |
394 | ||
395 | /* the following hooks are obsolete */ | |
396 | int (*self_test_count)(struct net_device *);/* use get_sset_count */ | |
397 | int (*get_stats_count)(struct net_device *);/* use get_sset_count */ | |
1da177e4 | 398 | }; |
c3ce7e20 | 399 | #endif /* __KERNEL__ */ |
1da177e4 LT |
400 | |
401 | /* CMDs currently supported */ | |
402 | #define ETHTOOL_GSET 0x00000001 /* Get settings. */ | |
403 | #define ETHTOOL_SSET 0x00000002 /* Set settings. */ | |
404 | #define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */ | |
405 | #define ETHTOOL_GREGS 0x00000004 /* Get NIC registers. */ | |
406 | #define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */ | |
407 | #define ETHTOOL_SWOL 0x00000006 /* Set wake-on-lan options. */ | |
408 | #define ETHTOOL_GMSGLVL 0x00000007 /* Get driver message level */ | |
409 | #define ETHTOOL_SMSGLVL 0x00000008 /* Set driver msg level. */ | |
410 | #define ETHTOOL_NWAY_RST 0x00000009 /* Restart autonegotiation. */ | |
411 | #define ETHTOOL_GLINK 0x0000000a /* Get link status (ethtool_value) */ | |
412 | #define ETHTOOL_GEEPROM 0x0000000b /* Get EEPROM data */ | |
413 | #define ETHTOOL_SEEPROM 0x0000000c /* Set EEPROM data. */ | |
414 | #define ETHTOOL_GCOALESCE 0x0000000e /* Get coalesce config */ | |
415 | #define ETHTOOL_SCOALESCE 0x0000000f /* Set coalesce config. */ | |
416 | #define ETHTOOL_GRINGPARAM 0x00000010 /* Get ring parameters */ | |
417 | #define ETHTOOL_SRINGPARAM 0x00000011 /* Set ring parameters. */ | |
418 | #define ETHTOOL_GPAUSEPARAM 0x00000012 /* Get pause parameters */ | |
419 | #define ETHTOOL_SPAUSEPARAM 0x00000013 /* Set pause parameters. */ | |
420 | #define ETHTOOL_GRXCSUM 0x00000014 /* Get RX hw csum enable (ethtool_value) */ | |
421 | #define ETHTOOL_SRXCSUM 0x00000015 /* Set RX hw csum enable (ethtool_value) */ | |
422 | #define ETHTOOL_GTXCSUM 0x00000016 /* Get TX hw csum enable (ethtool_value) */ | |
423 | #define ETHTOOL_STXCSUM 0x00000017 /* Set TX hw csum enable (ethtool_value) */ | |
424 | #define ETHTOOL_GSG 0x00000018 /* Get scatter-gather enable | |
425 | * (ethtool_value) */ | |
426 | #define ETHTOOL_SSG 0x00000019 /* Set scatter-gather enable | |
427 | * (ethtool_value). */ | |
428 | #define ETHTOOL_TEST 0x0000001a /* execute NIC self-test. */ | |
429 | #define ETHTOOL_GSTRINGS 0x0000001b /* get specified string set */ | |
430 | #define ETHTOOL_PHYS_ID 0x0000001c /* identify the NIC */ | |
431 | #define ETHTOOL_GSTATS 0x0000001d /* get NIC-specific statistics */ | |
432 | #define ETHTOOL_GTSO 0x0000001e /* Get TSO enable (ethtool_value) */ | |
433 | #define ETHTOOL_STSO 0x0000001f /* Set TSO enable (ethtool_value) */ | |
a6f9a705 | 434 | #define ETHTOOL_GPERMADDR 0x00000020 /* Get permanent hardware address */ |
e89e9cf5 AR |
435 | #define ETHTOOL_GUFO 0x00000021 /* Get UFO enable (ethtool_value) */ |
436 | #define ETHTOOL_SUFO 0x00000022 /* Set UFO enable (ethtool_value) */ | |
37c3185a HX |
437 | #define ETHTOOL_GGSO 0x00000023 /* Get GSO enable (ethtool_value) */ |
438 | #define ETHTOOL_SGSO 0x00000024 /* Set GSO enable (ethtool_value) */ | |
3ae7c0b2 JG |
439 | #define ETHTOOL_GFLAGS 0x00000025 /* Get flags bitmap(ethtool_value) */ |
440 | #define ETHTOOL_SFLAGS 0x00000026 /* Set flags bitmap(ethtool_value) */ | |
339bf024 JG |
441 | #define ETHTOOL_GPFLAGS 0x00000027 /* Get driver-private flags bitmap */ |
442 | #define ETHTOOL_SPFLAGS 0x00000028 /* Set driver-private flags bitmap */ | |
1da177e4 LT |
443 | |
444 | /* compatibility with older code */ | |
445 | #define SPARC_ETH_GSET ETHTOOL_GSET | |
446 | #define SPARC_ETH_SSET ETHTOOL_SSET | |
447 | ||
448 | /* Indicates what features are supported by the interface. */ | |
449 | #define SUPPORTED_10baseT_Half (1 << 0) | |
450 | #define SUPPORTED_10baseT_Full (1 << 1) | |
451 | #define SUPPORTED_100baseT_Half (1 << 2) | |
452 | #define SUPPORTED_100baseT_Full (1 << 3) | |
453 | #define SUPPORTED_1000baseT_Half (1 << 4) | |
454 | #define SUPPORTED_1000baseT_Full (1 << 5) | |
455 | #define SUPPORTED_Autoneg (1 << 6) | |
456 | #define SUPPORTED_TP (1 << 7) | |
457 | #define SUPPORTED_AUI (1 << 8) | |
458 | #define SUPPORTED_MII (1 << 9) | |
459 | #define SUPPORTED_FIBRE (1 << 10) | |
460 | #define SUPPORTED_BNC (1 << 11) | |
461 | #define SUPPORTED_10000baseT_Full (1 << 12) | |
00db8189 AF |
462 | #define SUPPORTED_Pause (1 << 13) |
463 | #define SUPPORTED_Asym_Pause (1 << 14) | |
427c2196 | 464 | #define SUPPORTED_2500baseX_Full (1 << 15) |
1da177e4 LT |
465 | |
466 | /* Indicates what features are advertised by the interface. */ | |
467 | #define ADVERTISED_10baseT_Half (1 << 0) | |
468 | #define ADVERTISED_10baseT_Full (1 << 1) | |
469 | #define ADVERTISED_100baseT_Half (1 << 2) | |
470 | #define ADVERTISED_100baseT_Full (1 << 3) | |
471 | #define ADVERTISED_1000baseT_Half (1 << 4) | |
472 | #define ADVERTISED_1000baseT_Full (1 << 5) | |
473 | #define ADVERTISED_Autoneg (1 << 6) | |
474 | #define ADVERTISED_TP (1 << 7) | |
475 | #define ADVERTISED_AUI (1 << 8) | |
476 | #define ADVERTISED_MII (1 << 9) | |
477 | #define ADVERTISED_FIBRE (1 << 10) | |
478 | #define ADVERTISED_BNC (1 << 11) | |
479 | #define ADVERTISED_10000baseT_Full (1 << 12) | |
00db8189 AF |
480 | #define ADVERTISED_Pause (1 << 13) |
481 | #define ADVERTISED_Asym_Pause (1 << 14) | |
427c2196 | 482 | #define ADVERTISED_2500baseX_Full (1 << 15) |
1da177e4 LT |
483 | |
484 | /* The following are all involved in forcing a particular link | |
485 | * mode for the device for setting things. When getting the | |
486 | * devices settings, these indicate the current mode and whether | |
487 | * it was foced up into this mode or autonegotiated. | |
488 | */ | |
489 | ||
5b0c76ad | 490 | /* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */ |
1da177e4 LT |
491 | #define SPEED_10 10 |
492 | #define SPEED_100 100 | |
493 | #define SPEED_1000 1000 | |
5b0c76ad | 494 | #define SPEED_2500 2500 |
1da177e4 LT |
495 | #define SPEED_10000 10000 |
496 | ||
497 | /* Duplex, half or full. */ | |
498 | #define DUPLEX_HALF 0x00 | |
499 | #define DUPLEX_FULL 0x01 | |
500 | ||
501 | /* Which connector port. */ | |
502 | #define PORT_TP 0x00 | |
503 | #define PORT_AUI 0x01 | |
504 | #define PORT_MII 0x02 | |
505 | #define PORT_FIBRE 0x03 | |
506 | #define PORT_BNC 0x04 | |
507 | ||
508 | /* Which transceiver to use. */ | |
509 | #define XCVR_INTERNAL 0x00 | |
510 | #define XCVR_EXTERNAL 0x01 | |
511 | #define XCVR_DUMMY1 0x02 | |
512 | #define XCVR_DUMMY2 0x03 | |
513 | #define XCVR_DUMMY3 0x04 | |
514 | ||
515 | /* Enable or disable autonegotiation. If this is set to enable, | |
516 | * the forced link modes above are completely ignored. | |
517 | */ | |
518 | #define AUTONEG_DISABLE 0x00 | |
519 | #define AUTONEG_ENABLE 0x01 | |
520 | ||
521 | /* Wake-On-Lan options. */ | |
522 | #define WAKE_PHY (1 << 0) | |
523 | #define WAKE_UCAST (1 << 1) | |
524 | #define WAKE_MCAST (1 << 2) | |
525 | #define WAKE_BCAST (1 << 3) | |
526 | #define WAKE_ARP (1 << 4) | |
527 | #define WAKE_MAGIC (1 << 5) | |
528 | #define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */ | |
529 | ||
530 | #endif /* _LINUX_ETHTOOL_H */ |