asoc/multi-component: fsl: add support for 36-bit physical addresses

[deliverable/linux.git] / sound / soc / fsl / fsl_ssi.c

/*
 * Freescale SSI ALSA SoC Digital Audio Interface (DAI) driver
 *
 * Author: Timur Tabi <timur@freescale.com>
 *
 * Copyright 2007-2010 Freescale Semiconductor, Inc.
 *
 * This file is licensed under the terms of the GNU General Public License
 * version 2.  This program is licensed "as is" without any warranty of any
 * kind, whether express or implied.
 */

#include <linux/init.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/device.h>
#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/of_platform.h>

#include <sound/core.h>
#include <sound/pcm.h>
#include <sound/pcm_params.h>
#include <sound/initval.h>
#include <sound/soc.h>

#include "fsl_ssi.h"

/**
 * FSLSSI_I2S_RATES: sample rates supported by the I2S
 *
 * This driver currently only supports the SSI running in I2S slave mode,
 * which means the codec determines the sample rate.  Therefore, we tell
 * ALSA that we support all rates and let the codec driver decide what rates
 * are really supported.
 */
#define FSLSSI_I2S_RATES (SNDRV_PCM_RATE_5512 | SNDRV_PCM_RATE_8000_192000 | \
			  SNDRV_PCM_RATE_CONTINUOUS)

/**
 * FSLSSI_I2S_FORMATS: audio formats supported by the SSI
 *
 * This driver currently only supports the SSI running in I2S slave mode.
 *
 * The SSI has a limitation in that the samples must be in the same byte
 * order as the host CPU.  This is because when multiple bytes are written
 * to the STX register, the bytes and bits must be written in the same
 * order.  The STX is a shift register, so all the bits need to be aligned
 * (bit-endianness must match byte-endianness).  Processors typically write
 * the bits within a byte in the same order that the bytes of a word are
 * written in.  So if the host CPU is big-endian, then only big-endian
 * samples will be written to STX properly.
 */
#ifdef __BIG_ENDIAN
#define FSLSSI_I2S_FORMATS (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_BE | \
	 SNDRV_PCM_FMTBIT_S18_3BE | SNDRV_PCM_FMTBIT_S20_3BE | \
	 SNDRV_PCM_FMTBIT_S24_3BE | SNDRV_PCM_FMTBIT_S24_BE)
#else
#define FSLSSI_I2S_FORMATS (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_LE | \
	 SNDRV_PCM_FMTBIT_S18_3LE | SNDRV_PCM_FMTBIT_S20_3LE | \
	 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_LE)
#endif

/* SIER bitflag of interrupts to enable */
#define SIER_FLAGS (CCSR_SSI_SIER_TFRC_EN | CCSR_SSI_SIER_TDMAE | \
		    CCSR_SSI_SIER_TIE | CCSR_SSI_SIER_TUE0_EN | \
		    CCSR_SSI_SIER_TUE1_EN | CCSR_SSI_SIER_RFRC_EN | \
		    CCSR_SSI_SIER_RDMAE | CCSR_SSI_SIER_RIE | \
		    CCSR_SSI_SIER_ROE0_EN | CCSR_SSI_SIER_ROE1_EN)

/**
 * fsl_ssi_private: per-SSI private data
 *
 * @ssi: pointer to the SSI's registers
 * @ssi_phys: physical address of the SSI registers
 * @irq: IRQ of this SSI
 * @first_stream: pointer to the stream that was opened first
 * @second_stream: pointer to second stream
 * @playback: the number of playback streams opened
 * @capture: the number of capture streams opened
 * @asynchronous: 0=synchronous mode, 1=asynchronous mode
 * @cpu_dai: the CPU DAI for this device
 * @dev_attr: the sysfs device attribute structure
 * @stats: SSI statistics
 * @name: name for this device
 */
struct fsl_ssi_private {
	struct ccsr_ssi __iomem *ssi;
	dma_addr_t ssi_phys;
	unsigned int irq;
	struct snd_pcm_substream *first_stream;
	struct snd_pcm_substream *second_stream;
	unsigned int playback;
	unsigned int capture;
	int asynchronous;
	struct snd_soc_dai_driver cpu_dai_drv;
	struct device_attribute dev_attr;
	struct platform_device *pdev;

	struct {
		unsigned int rfrc;
		unsigned int tfrc;
		unsigned int cmdau;
		unsigned int cmddu;
		unsigned int rxt;
		unsigned int rdr1;
		unsigned int rdr0;
		unsigned int tde1;
		unsigned int tde0;
		unsigned int roe1;
		unsigned int roe0;
		unsigned int tue1;
		unsigned int tue0;
		unsigned int tfs;
		unsigned int rfs;
		unsigned int tls;
		unsigned int rls;
		unsigned int rff1;
		unsigned int rff0;
		unsigned int tfe1;
		unsigned int tfe0;
	} stats;

	char name[1];
};

/**
 * fsl_ssi_isr: SSI interrupt handler
 *
 * Although it's possible to use the interrupt handler to send and receive
 * data to/from the SSI, we use the DMA instead.  Programming is more
 * complicated, but the performance is much better.
 *
 * This interrupt handler is used only to gather statistics.
 *
 * @irq: IRQ of the SSI device
 * @dev_id: pointer to the ssi_private structure for this SSI device
 */
static irqreturn_t fsl_ssi_isr(int irq, void *dev_id)
{
	struct fsl_ssi_private *ssi_private = dev_id;
	struct ccsr_ssi __iomem *ssi = ssi_private->ssi;
	irqreturn_t ret = IRQ_NONE;
	__be32 sisr;
	__be32 sisr2 = 0;

	/* We got an interrupt, so read the status register to see what we
	   were interrupted for.  We mask it with the Interrupt Enable register
	   so that we only check for events that we're interested in.
	 */
	sisr = in_be32(&ssi->sisr) & SIER_FLAGS;

	if (sisr & CCSR_SSI_SISR_RFRC) {
		ssi_private->stats.rfrc++;
		sisr2 |= CCSR_SSI_SISR_RFRC;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_TFRC) {
		ssi_private->stats.tfrc++;
		sisr2 |= CCSR_SSI_SISR_TFRC;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_CMDAU) {
		ssi_private->stats.cmdau++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_CMDDU) {
		ssi_private->stats.cmddu++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_RXT) {
		ssi_private->stats.rxt++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_RDR1) {
		ssi_private->stats.rdr1++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_RDR0) {
		ssi_private->stats.rdr0++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_TDE1) {
		ssi_private->stats.tde1++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_TDE0) {
		ssi_private->stats.tde0++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_ROE1) {
		ssi_private->stats.roe1++;
		sisr2 |= CCSR_SSI_SISR_ROE1;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_ROE0) {
		ssi_private->stats.roe0++;
		sisr2 |= CCSR_SSI_SISR_ROE0;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_TUE1) {
		ssi_private->stats.tue1++;
		sisr2 |= CCSR_SSI_SISR_TUE1;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_TUE0) {
		ssi_private->stats.tue0++;
		sisr2 |= CCSR_SSI_SISR_TUE0;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_TFS) {
		ssi_private->stats.tfs++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_RFS) {
		ssi_private->stats.rfs++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_TLS) {
		ssi_private->stats.tls++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_RLS) {
		ssi_private->stats.rls++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_RFF1) {
		ssi_private->stats.rff1++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_RFF0) {
		ssi_private->stats.rff0++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_TFE1) {
		ssi_private->stats.tfe1++;
		ret = IRQ_HANDLED;
	}

	if (sisr & CCSR_SSI_SISR_TFE0) {
		ssi_private->stats.tfe0++;
		ret = IRQ_HANDLED;
	}

	/* Clear the bits that we set */
	if (sisr2)
		out_be32(&ssi->sisr, sisr2);

	return ret;
}

/**
 * fsl_ssi_startup: create a new substream
 *
 * This is the first function called when a stream is opened.
 *
 * If this is the first stream open, then grab the IRQ and program most of
 * the SSI registers.
 */
static int fsl_ssi_startup(struct snd_pcm_substream *substream,
			   struct snd_soc_dai *dai)
{
	struct snd_soc_pcm_runtime *rtd = substream->private_data;
	struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(rtd->cpu_dai);

	/*
	 * If this is the first stream opened, then request the IRQ
	 * and initialize the SSI registers.
	 */
	if (!ssi_private->playback && !ssi_private->capture) {
		struct ccsr_ssi __iomem *ssi = ssi_private->ssi;
		int ret;

		/* The 'name' should not have any slashes in it. */
		ret = request_irq(ssi_private->irq, fsl_ssi_isr, 0,
				  ssi_private->name, ssi_private);
		if (ret < 0) {
			dev_err(substream->pcm->card->dev,
				"could not claim irq %u\n", ssi_private->irq);
			return ret;
		}

		/*
		 * Section 16.5 of the MPC8610 reference manual says that the
		 * SSI needs to be disabled before updating the registers we set
		 * here.
		 */
		clrbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);

		/*
		 * Program the SSI into I2S Slave Non-Network Synchronous mode.
		 * Also enable the transmit and receive FIFO.
		 *
		 * FIXME: Little-endian samples require a different shift dir
		 */
		clrsetbits_be32(&ssi->scr,
			CCSR_SSI_SCR_I2S_MODE_MASK | CCSR_SSI_SCR_SYN,
			CCSR_SSI_SCR_TFR_CLK_DIS | CCSR_SSI_SCR_I2S_MODE_SLAVE
			| (ssi_private->asynchronous ? 0 : CCSR_SSI_SCR_SYN));

		out_be32(&ssi->stcr,
			 CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TFEN0 |
			 CCSR_SSI_STCR_TFSI | CCSR_SSI_STCR_TEFS |
			 CCSR_SSI_STCR_TSCKP);

		out_be32(&ssi->srcr,
			 CCSR_SSI_SRCR_RXBIT0 | CCSR_SSI_SRCR_RFEN0 |
			 CCSR_SSI_SRCR_RFSI | CCSR_SSI_SRCR_REFS |
			 CCSR_SSI_SRCR_RSCKP);

		/*
		 * The DC and PM bits are only used if the SSI is the clock
		 * master.
		 */

		/* 4. Enable the interrupts and DMA requests */
		out_be32(&ssi->sier, SIER_FLAGS);

		/*
		 * Set the watermark for transmit FIFI 0 and receive FIFO 0. We
		 * don't use FIFO 1.  Since the SSI only supports stereo, the
		 * watermark should never be an odd number.
		 */
		out_be32(&ssi->sfcsr,
			 CCSR_SSI_SFCSR_TFWM0(6) | CCSR_SSI_SFCSR_RFWM0(2));

		/*
		 * We keep the SSI disabled because if we enable it, then the
		 * DMA controller will start.  It's not supposed to start until
		 * the SCR.TE (or SCR.RE) bit is set, but it does anyway.  The
		 * DMA controller will transfer one "BWC" of data (i.e. the
		 * amount of data that the MR.BWC bits are set to).  The reason
		 * this is bad is because at this point, the PCM driver has not
		 * finished initializing the DMA controller.
		 */
	}

	if (!ssi_private->first_stream)
		ssi_private->first_stream = substream;
	else {
		/* This is the second stream open, so we need to impose sample
		 * rate and maybe sample size constraints.  Note that this can
		 * cause a race condition if the second stream is opened before
		 * the first stream is fully initialized.
		 *
		 * We provide some protection by checking to make sure the first
		 * stream is initialized, but it's not perfect.  ALSA sometimes
		 * re-initializes the driver with a different sample rate or
		 * size.  If the second stream is opened before the first stream
		 * has received its final parameters, then the second stream may
		 * be constrained to the wrong sample rate or size.
		 *
		 * FIXME: This code does not handle opening and closing streams
		 * repeatedly.  If you open two streams and then close the first
		 * one, you may not be able to open another stream until you
		 * close the second one as well.
		 */
		struct snd_pcm_runtime *first_runtime =
			ssi_private->first_stream->runtime;

		if (!first_runtime->sample_bits) {
			dev_err(substream->pcm->card->dev,
				"set sample size in %s stream first\n",
				substream->stream == SNDRV_PCM_STREAM_PLAYBACK
				? "capture" : "playback");
			return -EAGAIN;
		}

		/* If we're in synchronous mode, then we need to constrain
		 * the sample size as well.  We don't support independent sample
		 * rates in asynchronous mode.
		 */
		if (!ssi_private->asynchronous)
			snd_pcm_hw_constraint_minmax(substream->runtime,
				SNDRV_PCM_HW_PARAM_SAMPLE_BITS,
				first_runtime->sample_bits,
				first_runtime->sample_bits);

		ssi_private->second_stream = substream;
	}

	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
		ssi_private->playback++;

	if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
		ssi_private->capture++;

	return 0;
}

/**
 * fsl_ssi_hw_params - program the sample size
 *
 * Most of the SSI registers have been programmed in the startup function,
 * but the word length must be programmed here.  Unfortunately, programming
 * the SxCCR.WL bits requires the SSI to be temporarily disabled.  This can
 * cause a problem with supporting simultaneous playback and capture.  If
 * the SSI is already playing a stream, then that stream may be temporarily
 * stopped when you start capture.
 *
 * Note: The SxCCR.DC and SxCCR.PM bits are only used if the SSI is the
 * clock master.
 */
static int fsl_ssi_hw_params(struct snd_pcm_substream *substream,
	struct snd_pcm_hw_params *hw_params, struct snd_soc_dai *cpu_dai)
{
	struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(cpu_dai);

	if (substream == ssi_private->first_stream) {
		struct ccsr_ssi __iomem *ssi = ssi_private->ssi;
		unsigned int sample_size =
			snd_pcm_format_width(params_format(hw_params));
		u32 wl = CCSR_SSI_SxCCR_WL(sample_size);

		/* The SSI should always be disabled at this points (SSIEN=0) */

		/* In synchronous mode, the SSI uses STCCR for capture */
		if ((substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ||
		    !ssi_private->asynchronous)
			clrsetbits_be32(&ssi->stccr,
					CCSR_SSI_SxCCR_WL_MASK, wl);
		else
			clrsetbits_be32(&ssi->srccr,
					CCSR_SSI_SxCCR_WL_MASK, wl);
	}

	return 0;
}

/**
 * fsl_ssi_trigger: start and stop the DMA transfer.
 *
 * This function is called by ALSA to start, stop, pause, and resume the DMA
 * transfer of data.
 *
 * The DMA channel is in external master start and pause mode, which
 * means the SSI completely controls the flow of data.
 */
static int fsl_ssi_trigger(struct snd_pcm_substream *substream, int cmd,
			   struct snd_soc_dai *dai)
{
	struct snd_soc_pcm_runtime *rtd = substream->private_data;
	struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(rtd->cpu_dai);
	struct ccsr_ssi __iomem *ssi = ssi_private->ssi;

	switch (cmd) {
	case SNDRV_PCM_TRIGGER_START:
		clrbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);
	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
		if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
			setbits32(&ssi->scr,
				CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_TE);
		else
			setbits32(&ssi->scr,
				CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_RE);
		break;

	case SNDRV_PCM_TRIGGER_STOP:
	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
		if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
			clrbits32(&ssi->scr, CCSR_SSI_SCR_TE);
		else
			clrbits32(&ssi->scr, CCSR_SSI_SCR_RE);
		break;

	default:
		return -EINVAL;
	}

	return 0;
}

/**
 * fsl_ssi_shutdown: shutdown the SSI
 *
 * Shutdown the SSI if there are no other substreams open.
 */
static void fsl_ssi_shutdown(struct snd_pcm_substream *substream,
			     struct snd_soc_dai *dai)
{
	struct snd_soc_pcm_runtime *rtd = substream->private_data;
	struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(rtd->cpu_dai);

	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
		ssi_private->playback--;

	if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
		ssi_private->capture--;

	if (ssi_private->first_stream == substream)
		ssi_private->first_stream = ssi_private->second_stream;

	ssi_private->second_stream = NULL;

	/*
	 * If this is the last active substream, disable the SSI and release
	 * the IRQ.
	 */
	if (!ssi_private->playback && !ssi_private->capture) {
		struct ccsr_ssi __iomem *ssi = ssi_private->ssi;

		clrbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);

		free_irq(ssi_private->irq, ssi_private);
	}
}

static struct snd_soc_dai_ops fsl_ssi_dai_ops = {
	.startup	= fsl_ssi_startup,
	.hw_params	= fsl_ssi_hw_params,
	.shutdown	= fsl_ssi_shutdown,
	.trigger	= fsl_ssi_trigger,
};

/* Template for the CPU dai driver structure */
static struct snd_soc_dai_driver fsl_ssi_dai_template = {
	.playback = {
		/* The SSI does not support monaural audio. */
		.channels_min = 2,
		.channels_max = 2,
		.rates = FSLSSI_I2S_RATES,
		.formats = FSLSSI_I2S_FORMATS,
	},
	.capture = {
		.channels_min = 2,
		.channels_max = 2,
		.rates = FSLSSI_I2S_RATES,
		.formats = FSLSSI_I2S_FORMATS,
	},
	.ops = &fsl_ssi_dai_ops,
};

/* Show the statistics of a flag only if its interrupt is enabled.  The
 * compiler will optimze this code to a no-op if the interrupt is not
 * enabled.
 */
#define SIER_SHOW(flag, name) \
	do { \
		if (SIER_FLAGS & CCSR_SSI_SIER_##flag) \
			length += sprintf(buf + length, #name "=%u\n", \
				ssi_private->stats.name); \
	} while (0)


/**
 * fsl_sysfs_ssi_show: display SSI statistics
 *
 * Display the statistics for the current SSI device.  To avoid confusion,
 * we only show those counts that are enabled.
 */
static ssize_t fsl_sysfs_ssi_show(struct device *dev,
	struct device_attribute *attr, char *buf)
{
	struct fsl_ssi_private *ssi_private =
		container_of(attr, struct fsl_ssi_private, dev_attr);
	ssize_t length = 0;

	SIER_SHOW(RFRC_EN, rfrc);
	SIER_SHOW(TFRC_EN, tfrc);
	SIER_SHOW(CMDAU_EN, cmdau);
	SIER_SHOW(CMDDU_EN, cmddu);
	SIER_SHOW(RXT_EN, rxt);
	SIER_SHOW(RDR1_EN, rdr1);
	SIER_SHOW(RDR0_EN, rdr0);
	SIER_SHOW(TDE1_EN, tde1);
	SIER_SHOW(TDE0_EN, tde0);
	SIER_SHOW(ROE1_EN, roe1);
	SIER_SHOW(ROE0_EN, roe0);
	SIER_SHOW(TUE1_EN, tue1);
	SIER_SHOW(TUE0_EN, tue0);
	SIER_SHOW(TFS_EN, tfs);
	SIER_SHOW(RFS_EN, rfs);
	SIER_SHOW(TLS_EN, tls);
	SIER_SHOW(RLS_EN, rls);
	SIER_SHOW(RFF1_EN, rff1);
	SIER_SHOW(RFF0_EN, rff0);
	SIER_SHOW(TFE1_EN, tfe1);
	SIER_SHOW(TFE0_EN, tfe0);

	return length;
}

/**
 * Make every character in a string lower-case
 */
static void make_lowercase(char *s)
{
	char *p = s;
	char c;

	while ((c = *p)) {
		if ((c >= 'A') && (c <= 'Z'))
			*p = c + ('a' - 'A');
		p++;
	}
}

static int __devinit fsl_ssi_probe(struct of_device *of_dev,
				   const struct of_device_id *match)
{
	struct fsl_ssi_private *ssi_private;
	int ret = 0;
	struct device_attribute *dev_attr;
	struct device_node *np = of_dev->dev.of_node;
	const char *p, *sprop;
	struct resource res;
	char name[64];

	/* We are only interested in SSIs with a codec phandle in them, so let's
	 * make sure this SSI has one.
	 */
	if (!of_get_property(np, "codec-handle", NULL))
		return -ENODEV;

	/* We only support the SSI in "I2S Slave" mode */
	sprop = of_get_property(np, "fsl,mode", NULL);
	if (!sprop || strcmp(sprop, "i2s-slave")) {
		dev_notice(&of_dev->dev, "mode %s is unsupported\n", sprop);
		return -ENODEV;
	}

	/* The DAI name is the last part of the full name of the node. */
	p = strrchr(np->full_name, '/') + 1;
	ssi_private = kzalloc(sizeof(struct fsl_ssi_private) + strlen(p),
			      GFP_KERNEL);
	if (!ssi_private) {
		dev_err(&of_dev->dev, "could not allocate DAI object\n");
		return -ENOMEM;
	}

	strcpy(ssi_private->name, p);

	/* Initialize this copy of the CPU DAI driver structure */
	memcpy(&ssi_private->cpu_dai_drv, &fsl_ssi_dai_template,
	       sizeof(fsl_ssi_dai_template));
	ssi_private->cpu_dai_drv.name = ssi_private->name;

	/* Get the addresses and IRQ */
	ret = of_address_to_resource(np, 0, &res);
	if (ret) {
		dev_err(&of_dev->dev, "could not determine device resources\n");
		kfree(ssi_private);
		return ret;
	}
	ssi_private->ssi = ioremap(res.start, 1 + res.end - res.start);
	ssi_private->ssi_phys = res.start;
	ssi_private->irq = irq_of_parse_and_map(np, 0);

	/* Are the RX and the TX clocks locked? */
	if (of_find_property(np, "fsl,ssi-asynchronous", NULL))
		ssi_private->asynchronous = 1;
	else
		ssi_private->cpu_dai_drv.symmetric_rates = 1;

	/* Initialize the the device_attribute structure */
	dev_attr = &ssi_private->dev_attr;
	dev_attr->attr.name = "statistics";
	dev_attr->attr.mode = S_IRUGO;
	dev_attr->show = fsl_sysfs_ssi_show;

	ret = device_create_file(&of_dev->dev, dev_attr);
	if (ret) {
		dev_err(&of_dev->dev, "could not create sysfs %s file\n",
			ssi_private->dev_attr.attr.name);
		kfree(ssi_private);
		return ret;
	}

	/* Register with ASoC */
	dev_set_drvdata(&of_dev->dev, ssi_private);

	ret = snd_soc_register_dai(&of_dev->dev, &ssi_private->cpu_dai_drv);
	if (ret != 0) {
		dev_err(&of_dev->dev, "failed to register DAI: %d\n", ret);
		kfree(ssi_private);
		return ret;
	}

	/* Trigger the machine driver's probe function.  The platform driver
	 * name of the machine driver is taken from the /model property of the
	 * device tree.  We also pass the address of the CPU DAI driver
	 * structure.
	 */
	sprop = of_get_property(of_find_node_by_path("/"), "model", NULL);
	/* Sometimes the model name has a "fsl," prefix, so we strip that. */
	p = strrchr(sprop, ',');
	if (p)
		sprop = p + 1;
	snprintf(name, sizeof(name), "snd-soc-%s", sprop);
	make_lowercase(name);

	ssi_private->pdev =
		platform_device_register_data(&of_dev->dev, name, 0, NULL, 0);
	if (IS_ERR(ssi_private->pdev)) {
		ret = PTR_ERR(ssi_private->pdev);
		dev_err(&of_dev->dev, "failed to register platform: %d\n", ret);
		kfree(ssi_private);
		return ret;
	}

	return 0;
}

/**
 * fsl_ssi_destroy_dai: destroy the snd_soc_dai object
 *
 * This function undoes the operations of fsl_ssi_probe()
 */
static int fsl_ssi_remove(struct of_device *of_dev)
{
	struct fsl_ssi_private *ssi_private = dev_get_drvdata(&of_dev->dev);

	platform_device_unregister(ssi_private->pdev);
	snd_soc_unregister_dai(&of_dev->dev);
	device_remove_file(&of_dev->dev, &ssi_private->dev_attr);

	kfree(ssi_private);
	dev_set_drvdata(&of_dev->dev, NULL);

	return 0;
}

static const struct of_device_id fsl_ssi_ids[] = {
	{ .compatible = "fsl,mpc8610-ssi", },
	{}
};
MODULE_DEVICE_TABLE(of, fsl_ssi_ids);

static struct of_platform_driver fsl_ssi_driver = {
	.driver = {
		.name = "fsl-ssi-dai",
		.owner = THIS_MODULE,
		.of_match_table = fsl_ssi_ids,
	},
	.probe = fsl_ssi_probe,
	.remove = fsl_ssi_remove,
};

static int __init fsl_ssi_init(void)
{
	printk(KERN_INFO "Freescale Synchronous Serial Interface (SSI) ASoC Driver\n");

	return of_register_platform_driver(&fsl_ssi_driver);
}

static void __exit fsl_ssi_exit(void)
{
	of_unregister_platform_driver(&fsl_ssi_driver);
}

module_init(fsl_ssi_init);
module_exit(fsl_ssi_exit);

MODULE_AUTHOR("Timur Tabi <timur@freescale.com>");
MODULE_DESCRIPTION("Freescale Synchronous Serial Interface (SSI) ASoC Driver");
MODULE_LICENSE("GPL v2");