| 1 | config ARM |
| 2 | bool |
| 3 | default y |
| 4 | select ARCH_BINFMT_ELF_RANDOMIZE_PIE |
| 5 | select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE |
| 6 | select ARCH_HAVE_CUSTOM_GPIO_H |
| 7 | select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST |
| 8 | select ARCH_WANT_IPC_PARSE_VERSION |
| 9 | select BUILDTIME_EXTABLE_SORT if MMU |
| 10 | select CPU_PM if (SUSPEND || CPU_IDLE) |
| 11 | select DCACHE_WORD_ACCESS if (CPU_V6 || CPU_V6K || CPU_V7) && !CPU_BIG_ENDIAN && MMU |
| 12 | select GENERIC_ATOMIC64 if (CPU_V6 || !CPU_32v6K || !AEABI) |
| 13 | select GENERIC_CLOCKEVENTS_BROADCAST if SMP |
| 14 | select GENERIC_IRQ_PROBE |
| 15 | select GENERIC_IRQ_SHOW |
| 16 | select GENERIC_PCI_IOMAP |
| 17 | select GENERIC_SMP_IDLE_THREAD |
| 18 | select GENERIC_STRNCPY_FROM_USER |
| 19 | select GENERIC_STRNLEN_USER |
| 20 | select HARDIRQS_SW_RESEND |
| 21 | select HAVE_AOUT |
| 22 | select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL |
| 23 | select HAVE_ARCH_KGDB |
| 24 | select HAVE_ARCH_SECCOMP_FILTER |
| 25 | select HAVE_ARCH_TRACEHOOK |
| 26 | select HAVE_BPF_JIT |
| 27 | select HAVE_C_RECORDMCOUNT |
| 28 | select HAVE_DEBUG_KMEMLEAK |
| 29 | select HAVE_DMA_API_DEBUG |
| 30 | select HAVE_DMA_ATTRS |
| 31 | select HAVE_DMA_CONTIGUOUS if MMU |
| 32 | select HAVE_DYNAMIC_FTRACE if (!XIP_KERNEL) |
| 33 | select HAVE_FTRACE_MCOUNT_RECORD if (!XIP_KERNEL) |
| 34 | select HAVE_FUNCTION_GRAPH_TRACER if (!THUMB2_KERNEL) |
| 35 | select HAVE_FUNCTION_TRACER if (!XIP_KERNEL) |
| 36 | select HAVE_GENERIC_DMA_COHERENT |
| 37 | select HAVE_GENERIC_HARDIRQS |
| 38 | select HAVE_HW_BREAKPOINT if (PERF_EVENTS && (CPU_V6 || CPU_V6K || CPU_V7)) |
| 39 | select HAVE_IDE if PCI || ISA || PCMCIA |
| 40 | select HAVE_KERNEL_GZIP |
| 41 | select HAVE_KERNEL_LZMA |
| 42 | select HAVE_KERNEL_LZO |
| 43 | select HAVE_KERNEL_XZ |
| 44 | select HAVE_KPROBES if !XIP_KERNEL |
| 45 | select HAVE_KRETPROBES if (HAVE_KPROBES) |
| 46 | select HAVE_MEMBLOCK |
| 47 | select HAVE_OPROFILE if (HAVE_PERF_EVENTS) |
| 48 | select HAVE_PERF_EVENTS |
| 49 | select HAVE_REGS_AND_STACK_ACCESS_API |
| 50 | select HAVE_SYSCALL_TRACEPOINTS |
| 51 | select HAVE_UID16 |
| 52 | select KTIME_SCALAR |
| 53 | select PERF_USE_VMALLOC |
| 54 | select RTC_LIB |
| 55 | select SYS_SUPPORTS_APM_EMULATION |
| 56 | select HAVE_MOD_ARCH_SPECIFIC if ARM_UNWIND |
| 57 | select MODULES_USE_ELF_REL |
| 58 | select CLONE_BACKWARDS |
| 59 | select OLD_SIGSUSPEND3 |
| 60 | select OLD_SIGACTION |
| 61 | help |
| 62 | The ARM series is a line of low-power-consumption RISC chip designs |
| 63 | licensed by ARM Ltd and targeted at embedded applications and |
| 64 | handhelds such as the Compaq IPAQ. ARM-based PCs are no longer |
| 65 | manufactured, but legacy ARM-based PC hardware remains popular in |
| 66 | Europe. There is an ARM Linux project with a web page at |
| 67 | <http://www.arm.linux.org.uk/>. |
| 68 | |
| 69 | config ARM_HAS_SG_CHAIN |
| 70 | bool |
| 71 | |
| 72 | config NEED_SG_DMA_LENGTH |
| 73 | bool |
| 74 | |
| 75 | config ARM_DMA_USE_IOMMU |
| 76 | bool |
| 77 | select ARM_HAS_SG_CHAIN |
| 78 | select NEED_SG_DMA_LENGTH |
| 79 | |
| 80 | if ARM_DMA_USE_IOMMU |
| 81 | |
| 82 | config ARM_DMA_IOMMU_ALIGNMENT |
| 83 | int "Maximum PAGE_SIZE order of alignment for DMA IOMMU buffers" |
| 84 | range 4 9 |
| 85 | default 8 |
| 86 | help |
| 87 | DMA mapping framework by default aligns all buffers to the smallest |
| 88 | PAGE_SIZE order which is greater than or equal to the requested buffer |
| 89 | size. This works well for buffers up to a few hundreds kilobytes, but |
| 90 | for larger buffers it just a waste of address space. Drivers which has |
| 91 | relatively small addressing window (like 64Mib) might run out of |
| 92 | virtual space with just a few allocations. |
| 93 | |
| 94 | With this parameter you can specify the maximum PAGE_SIZE order for |
| 95 | DMA IOMMU buffers. Larger buffers will be aligned only to this |
| 96 | specified order. The order is expressed as a power of two multiplied |
| 97 | by the PAGE_SIZE. |
| 98 | |
| 99 | endif |
| 100 | |
| 101 | config HAVE_PWM |
| 102 | bool |
| 103 | |
| 104 | config MIGHT_HAVE_PCI |
| 105 | bool |
| 106 | |
| 107 | config SYS_SUPPORTS_APM_EMULATION |
| 108 | bool |
| 109 | |
| 110 | config GENERIC_GPIO |
| 111 | bool |
| 112 | |
| 113 | config HAVE_TCM |
| 114 | bool |
| 115 | select GENERIC_ALLOCATOR |
| 116 | |
| 117 | config HAVE_PROC_CPU |
| 118 | bool |
| 119 | |
| 120 | config NO_IOPORT |
| 121 | bool |
| 122 | |
| 123 | config EISA |
| 124 | bool |
| 125 | ---help--- |
| 126 | The Extended Industry Standard Architecture (EISA) bus was |
| 127 | developed as an open alternative to the IBM MicroChannel bus. |
| 128 | |
| 129 | The EISA bus provided some of the features of the IBM MicroChannel |
| 130 | bus while maintaining backward compatibility with cards made for |
| 131 | the older ISA bus. The EISA bus saw limited use between 1988 and |
| 132 | 1995 when it was made obsolete by the PCI bus. |
| 133 | |
| 134 | Say Y here if you are building a kernel for an EISA-based machine. |
| 135 | |
| 136 | Otherwise, say N. |
| 137 | |
| 138 | config SBUS |
| 139 | bool |
| 140 | |
| 141 | config STACKTRACE_SUPPORT |
| 142 | bool |
| 143 | default y |
| 144 | |
| 145 | config HAVE_LATENCYTOP_SUPPORT |
| 146 | bool |
| 147 | depends on !SMP |
| 148 | default y |
| 149 | |
| 150 | config LOCKDEP_SUPPORT |
| 151 | bool |
| 152 | default y |
| 153 | |
| 154 | config TRACE_IRQFLAGS_SUPPORT |
| 155 | bool |
| 156 | default y |
| 157 | |
| 158 | config RWSEM_GENERIC_SPINLOCK |
| 159 | bool |
| 160 | default y |
| 161 | |
| 162 | config RWSEM_XCHGADD_ALGORITHM |
| 163 | bool |
| 164 | |
| 165 | config ARCH_HAS_ILOG2_U32 |
| 166 | bool |
| 167 | |
| 168 | config ARCH_HAS_ILOG2_U64 |
| 169 | bool |
| 170 | |
| 171 | config ARCH_HAS_CPUFREQ |
| 172 | bool |
| 173 | help |
| 174 | Internal node to signify that the ARCH has CPUFREQ support |
| 175 | and that the relevant menu configurations are displayed for |
| 176 | it. |
| 177 | |
| 178 | config GENERIC_HWEIGHT |
| 179 | bool |
| 180 | default y |
| 181 | |
| 182 | config GENERIC_CALIBRATE_DELAY |
| 183 | bool |
| 184 | default y |
| 185 | |
| 186 | config ARCH_MAY_HAVE_PC_FDC |
| 187 | bool |
| 188 | |
| 189 | config ZONE_DMA |
| 190 | bool |
| 191 | |
| 192 | config NEED_DMA_MAP_STATE |
| 193 | def_bool y |
| 194 | |
| 195 | config ARCH_HAS_DMA_SET_COHERENT_MASK |
| 196 | bool |
| 197 | |
| 198 | config GENERIC_ISA_DMA |
| 199 | bool |
| 200 | |
| 201 | config FIQ |
| 202 | bool |
| 203 | |
| 204 | config NEED_RET_TO_USER |
| 205 | bool |
| 206 | |
| 207 | config ARCH_MTD_XIP |
| 208 | bool |
| 209 | |
| 210 | config VECTORS_BASE |
| 211 | hex |
| 212 | default 0xffff0000 if MMU || CPU_HIGH_VECTOR |
| 213 | default DRAM_BASE if REMAP_VECTORS_TO_RAM |
| 214 | default 0x00000000 |
| 215 | help |
| 216 | The base address of exception vectors. |
| 217 | |
| 218 | config ARM_PATCH_PHYS_VIRT |
| 219 | bool "Patch physical to virtual translations at runtime" if EMBEDDED |
| 220 | default y |
| 221 | depends on !XIP_KERNEL && MMU |
| 222 | depends on !ARCH_REALVIEW || !SPARSEMEM |
| 223 | help |
| 224 | Patch phys-to-virt and virt-to-phys translation functions at |
| 225 | boot and module load time according to the position of the |
| 226 | kernel in system memory. |
| 227 | |
| 228 | This can only be used with non-XIP MMU kernels where the base |
| 229 | of physical memory is at a 16MB boundary. |
| 230 | |
| 231 | Only disable this option if you know that you do not require |
| 232 | this feature (eg, building a kernel for a single machine) and |
| 233 | you need to shrink the kernel to the minimal size. |
| 234 | |
| 235 | config NEED_MACH_GPIO_H |
| 236 | bool |
| 237 | help |
| 238 | Select this when mach/gpio.h is required to provide special |
| 239 | definitions for this platform. The need for mach/gpio.h should |
| 240 | be avoided when possible. |
| 241 | |
| 242 | config NEED_MACH_IO_H |
| 243 | bool |
| 244 | help |
| 245 | Select this when mach/io.h is required to provide special |
| 246 | definitions for this platform. The need for mach/io.h should |
| 247 | be avoided when possible. |
| 248 | |
| 249 | config NEED_MACH_MEMORY_H |
| 250 | bool |
| 251 | help |
| 252 | Select this when mach/memory.h is required to provide special |
| 253 | definitions for this platform. The need for mach/memory.h should |
| 254 | be avoided when possible. |
| 255 | |
| 256 | config PHYS_OFFSET |
| 257 | hex "Physical address of main memory" if MMU |
| 258 | depends on !ARM_PATCH_PHYS_VIRT && !NEED_MACH_MEMORY_H |
| 259 | default DRAM_BASE if !MMU |
| 260 | help |
| 261 | Please provide the physical address corresponding to the |
| 262 | location of main memory in your system. |
| 263 | |
| 264 | config GENERIC_BUG |
| 265 | def_bool y |
| 266 | depends on BUG |
| 267 | |
| 268 | source "init/Kconfig" |
| 269 | |
| 270 | source "kernel/Kconfig.freezer" |
| 271 | |
| 272 | menu "System Type" |
| 273 | |
| 274 | config MMU |
| 275 | bool "MMU-based Paged Memory Management Support" |
| 276 | default y |
| 277 | help |
| 278 | Select if you want MMU-based virtualised addressing space |
| 279 | support by paged memory management. If unsure, say 'Y'. |
| 280 | |
| 281 | # |
| 282 | # The "ARM system type" choice list is ordered alphabetically by option |
| 283 | # text. Please add new entries in the option alphabetic order. |
| 284 | # |
| 285 | choice |
| 286 | prompt "ARM system type" |
| 287 | default ARCH_VERSATILE if !MMU |
| 288 | default ARCH_MULTIPLATFORM if MMU |
| 289 | |
| 290 | config ARCH_MULTIPLATFORM |
| 291 | bool "Allow multiple platforms to be selected" |
| 292 | depends on MMU |
| 293 | select ARM_PATCH_PHYS_VIRT |
| 294 | select AUTO_ZRELADDR |
| 295 | select COMMON_CLK |
| 296 | select MULTI_IRQ_HANDLER |
| 297 | select SPARSE_IRQ |
| 298 | select USE_OF |
| 299 | |
| 300 | config ARCH_INTEGRATOR |
| 301 | bool "ARM Ltd. Integrator family" |
| 302 | select ARCH_HAS_CPUFREQ |
| 303 | select ARM_AMBA |
| 304 | select COMMON_CLK |
| 305 | select COMMON_CLK_VERSATILE |
| 306 | select GENERIC_CLOCKEVENTS |
| 307 | select HAVE_TCM |
| 308 | select ICST |
| 309 | select MULTI_IRQ_HANDLER |
| 310 | select NEED_MACH_MEMORY_H |
| 311 | select PLAT_VERSATILE |
| 312 | select SPARSE_IRQ |
| 313 | select VERSATILE_FPGA_IRQ |
| 314 | help |
| 315 | Support for ARM's Integrator platform. |
| 316 | |
| 317 | config ARCH_REALVIEW |
| 318 | bool "ARM Ltd. RealView family" |
| 319 | select ARCH_WANT_OPTIONAL_GPIOLIB |
| 320 | select ARM_AMBA |
| 321 | select ARM_TIMER_SP804 |
| 322 | select COMMON_CLK |
| 323 | select COMMON_CLK_VERSATILE |
| 324 | select GENERIC_CLOCKEVENTS |
| 325 | select GPIO_PL061 if GPIOLIB |
| 326 | select ICST |
| 327 | select NEED_MACH_MEMORY_H |
| 328 | select PLAT_VERSATILE |
| 329 | select PLAT_VERSATILE_CLCD |
| 330 | help |
| 331 | This enables support for ARM Ltd RealView boards. |
| 332 | |
| 333 | config ARCH_VERSATILE |
| 334 | bool "ARM Ltd. Versatile family" |
| 335 | select ARCH_WANT_OPTIONAL_GPIOLIB |
| 336 | select ARM_AMBA |
| 337 | select ARM_TIMER_SP804 |
| 338 | select ARM_VIC |
| 339 | select CLKDEV_LOOKUP |
| 340 | select GENERIC_CLOCKEVENTS |
| 341 | select HAVE_MACH_CLKDEV |
| 342 | select ICST |
| 343 | select PLAT_VERSATILE |
| 344 | select PLAT_VERSATILE_CLCD |
| 345 | select PLAT_VERSATILE_CLOCK |
| 346 | select VERSATILE_FPGA_IRQ |
| 347 | help |
| 348 | This enables support for ARM Ltd Versatile board. |
| 349 | |
| 350 | config ARCH_AT91 |
| 351 | bool "Atmel AT91" |
| 352 | select ARCH_REQUIRE_GPIOLIB |
| 353 | select CLKDEV_LOOKUP |
| 354 | select HAVE_CLK |
| 355 | select IRQ_DOMAIN |
| 356 | select NEED_MACH_GPIO_H |
| 357 | select NEED_MACH_IO_H if PCCARD |
| 358 | select PINCTRL |
| 359 | select PINCTRL_AT91 if USE_OF |
| 360 | help |
| 361 | This enables support for systems based on Atmel |
| 362 | AT91RM9200 and AT91SAM9* processors. |
| 363 | |
| 364 | config ARCH_BCM2835 |
| 365 | bool "Broadcom BCM2835 family" |
| 366 | select ARCH_REQUIRE_GPIOLIB |
| 367 | select ARM_AMBA |
| 368 | select ARM_ERRATA_411920 |
| 369 | select ARM_TIMER_SP804 |
| 370 | select CLKDEV_LOOKUP |
| 371 | select CLKSRC_OF |
| 372 | select COMMON_CLK |
| 373 | select CPU_V6 |
| 374 | select GENERIC_CLOCKEVENTS |
| 375 | select MULTI_IRQ_HANDLER |
| 376 | select PINCTRL |
| 377 | select PINCTRL_BCM2835 |
| 378 | select SPARSE_IRQ |
| 379 | select USE_OF |
| 380 | help |
| 381 | This enables support for the Broadcom BCM2835 SoC. This SoC is |
| 382 | use in the Raspberry Pi, and Roku 2 devices. |
| 383 | |
| 384 | config ARCH_CNS3XXX |
| 385 | bool "Cavium Networks CNS3XXX family" |
| 386 | select ARM_GIC |
| 387 | select CPU_V6K |
| 388 | select GENERIC_CLOCKEVENTS |
| 389 | select MIGHT_HAVE_CACHE_L2X0 |
| 390 | select MIGHT_HAVE_PCI |
| 391 | select PCI_DOMAINS if PCI |
| 392 | help |
| 393 | Support for Cavium Networks CNS3XXX platform. |
| 394 | |
| 395 | config ARCH_CLPS711X |
| 396 | bool "Cirrus Logic CLPS711x/EP721x/EP731x-based" |
| 397 | select ARCH_REQUIRE_GPIOLIB |
| 398 | select AUTO_ZRELADDR |
| 399 | select CLKDEV_LOOKUP |
| 400 | select COMMON_CLK |
| 401 | select CPU_ARM720T |
| 402 | select GENERIC_CLOCKEVENTS |
| 403 | select MULTI_IRQ_HANDLER |
| 404 | select NEED_MACH_MEMORY_H |
| 405 | select SPARSE_IRQ |
| 406 | help |
| 407 | Support for Cirrus Logic 711x/721x/731x based boards. |
| 408 | |
| 409 | config ARCH_GEMINI |
| 410 | bool "Cortina Systems Gemini" |
| 411 | select ARCH_REQUIRE_GPIOLIB |
| 412 | select ARCH_USES_GETTIMEOFFSET |
| 413 | select CPU_FA526 |
| 414 | help |
| 415 | Support for the Cortina Systems Gemini family SoCs |
| 416 | |
| 417 | config ARCH_SIRF |
| 418 | bool "CSR SiRF" |
| 419 | select ARCH_REQUIRE_GPIOLIB |
| 420 | select AUTO_ZRELADDR |
| 421 | select COMMON_CLK |
| 422 | select GENERIC_CLOCKEVENTS |
| 423 | select GENERIC_IRQ_CHIP |
| 424 | select MIGHT_HAVE_CACHE_L2X0 |
| 425 | select NO_IOPORT |
| 426 | select PINCTRL |
| 427 | select PINCTRL_SIRF |
| 428 | select USE_OF |
| 429 | help |
| 430 | Support for CSR SiRFprimaII/Marco/Polo platforms |
| 431 | |
| 432 | config ARCH_EBSA110 |
| 433 | bool "EBSA-110" |
| 434 | select ARCH_USES_GETTIMEOFFSET |
| 435 | select CPU_SA110 |
| 436 | select ISA |
| 437 | select NEED_MACH_IO_H |
| 438 | select NEED_MACH_MEMORY_H |
| 439 | select NO_IOPORT |
| 440 | help |
| 441 | This is an evaluation board for the StrongARM processor available |
| 442 | from Digital. It has limited hardware on-board, including an |
| 443 | Ethernet interface, two PCMCIA sockets, two serial ports and a |
| 444 | parallel port. |
| 445 | |
| 446 | config ARCH_EP93XX |
| 447 | bool "EP93xx-based" |
| 448 | select ARCH_HAS_HOLES_MEMORYMODEL |
| 449 | select ARCH_REQUIRE_GPIOLIB |
| 450 | select ARCH_USES_GETTIMEOFFSET |
| 451 | select ARM_AMBA |
| 452 | select ARM_VIC |
| 453 | select CLKDEV_LOOKUP |
| 454 | select CPU_ARM920T |
| 455 | select NEED_MACH_MEMORY_H |
| 456 | help |
| 457 | This enables support for the Cirrus EP93xx series of CPUs. |
| 458 | |
| 459 | config ARCH_FOOTBRIDGE |
| 460 | bool "FootBridge" |
| 461 | select CPU_SA110 |
| 462 | select FOOTBRIDGE |
| 463 | select GENERIC_CLOCKEVENTS |
| 464 | select HAVE_IDE |
| 465 | select NEED_MACH_IO_H if !MMU |
| 466 | select NEED_MACH_MEMORY_H |
| 467 | help |
| 468 | Support for systems based on the DC21285 companion chip |
| 469 | ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder. |
| 470 | |
| 471 | config ARCH_MXS |
| 472 | bool "Freescale MXS-based" |
| 473 | select ARCH_REQUIRE_GPIOLIB |
| 474 | select CLKDEV_LOOKUP |
| 475 | select CLKSRC_MMIO |
| 476 | select COMMON_CLK |
| 477 | select GENERIC_CLOCKEVENTS |
| 478 | select HAVE_CLK_PREPARE |
| 479 | select MULTI_IRQ_HANDLER |
| 480 | select PINCTRL |
| 481 | select SPARSE_IRQ |
| 482 | select USE_OF |
| 483 | help |
| 484 | Support for Freescale MXS-based family of processors |
| 485 | |
| 486 | config ARCH_NETX |
| 487 | bool "Hilscher NetX based" |
| 488 | select ARM_VIC |
| 489 | select CLKSRC_MMIO |
| 490 | select CPU_ARM926T |
| 491 | select GENERIC_CLOCKEVENTS |
| 492 | help |
| 493 | This enables support for systems based on the Hilscher NetX Soc |
| 494 | |
| 495 | config ARCH_H720X |
| 496 | bool "Hynix HMS720x-based" |
| 497 | select ARCH_USES_GETTIMEOFFSET |
| 498 | select CPU_ARM720T |
| 499 | select ISA_DMA_API |
| 500 | help |
| 501 | This enables support for systems based on the Hynix HMS720x |
| 502 | |
| 503 | config ARCH_IOP13XX |
| 504 | bool "IOP13xx-based" |
| 505 | depends on MMU |
| 506 | select ARCH_SUPPORTS_MSI |
| 507 | select CPU_XSC3 |
| 508 | select NEED_MACH_MEMORY_H |
| 509 | select NEED_RET_TO_USER |
| 510 | select PCI |
| 511 | select PLAT_IOP |
| 512 | select VMSPLIT_1G |
| 513 | help |
| 514 | Support for Intel's IOP13XX (XScale) family of processors. |
| 515 | |
| 516 | config ARCH_IOP32X |
| 517 | bool "IOP32x-based" |
| 518 | depends on MMU |
| 519 | select ARCH_REQUIRE_GPIOLIB |
| 520 | select CPU_XSCALE |
| 521 | select NEED_MACH_GPIO_H |
| 522 | select NEED_RET_TO_USER |
| 523 | select PCI |
| 524 | select PLAT_IOP |
| 525 | help |
| 526 | Support for Intel's 80219 and IOP32X (XScale) family of |
| 527 | processors. |
| 528 | |
| 529 | config ARCH_IOP33X |
| 530 | bool "IOP33x-based" |
| 531 | depends on MMU |
| 532 | select ARCH_REQUIRE_GPIOLIB |
| 533 | select CPU_XSCALE |
| 534 | select NEED_MACH_GPIO_H |
| 535 | select NEED_RET_TO_USER |
| 536 | select PCI |
| 537 | select PLAT_IOP |
| 538 | help |
| 539 | Support for Intel's IOP33X (XScale) family of processors. |
| 540 | |
| 541 | config ARCH_IXP4XX |
| 542 | bool "IXP4xx-based" |
| 543 | depends on MMU |
| 544 | select ARCH_HAS_DMA_SET_COHERENT_MASK |
| 545 | select ARCH_REQUIRE_GPIOLIB |
| 546 | select CLKSRC_MMIO |
| 547 | select CPU_XSCALE |
| 548 | select DMABOUNCE if PCI |
| 549 | select GENERIC_CLOCKEVENTS |
| 550 | select MIGHT_HAVE_PCI |
| 551 | select NEED_MACH_IO_H |
| 552 | help |
| 553 | Support for Intel's IXP4XX (XScale) family of processors. |
| 554 | |
| 555 | config ARCH_DOVE |
| 556 | bool "Marvell Dove" |
| 557 | select ARCH_REQUIRE_GPIOLIB |
| 558 | select CPU_V7 |
| 559 | select GENERIC_CLOCKEVENTS |
| 560 | select MIGHT_HAVE_PCI |
| 561 | select PINCTRL |
| 562 | select PINCTRL_DOVE |
| 563 | select PLAT_ORION_LEGACY |
| 564 | select USB_ARCH_HAS_EHCI |
| 565 | help |
| 566 | Support for the Marvell Dove SoC 88AP510 |
| 567 | |
| 568 | config ARCH_KIRKWOOD |
| 569 | bool "Marvell Kirkwood" |
| 570 | select ARCH_REQUIRE_GPIOLIB |
| 571 | select CPU_FEROCEON |
| 572 | select GENERIC_CLOCKEVENTS |
| 573 | select PCI |
| 574 | select PCI_QUIRKS |
| 575 | select PINCTRL |
| 576 | select PINCTRL_KIRKWOOD |
| 577 | select PLAT_ORION_LEGACY |
| 578 | help |
| 579 | Support for the following Marvell Kirkwood series SoCs: |
| 580 | 88F6180, 88F6192 and 88F6281. |
| 581 | |
| 582 | config ARCH_MV78XX0 |
| 583 | bool "Marvell MV78xx0" |
| 584 | select ARCH_REQUIRE_GPIOLIB |
| 585 | select CPU_FEROCEON |
| 586 | select GENERIC_CLOCKEVENTS |
| 587 | select PCI |
| 588 | select PLAT_ORION_LEGACY |
| 589 | help |
| 590 | Support for the following Marvell MV78xx0 series SoCs: |
| 591 | MV781x0, MV782x0. |
| 592 | |
| 593 | config ARCH_ORION5X |
| 594 | bool "Marvell Orion" |
| 595 | depends on MMU |
| 596 | select ARCH_REQUIRE_GPIOLIB |
| 597 | select CPU_FEROCEON |
| 598 | select GENERIC_CLOCKEVENTS |
| 599 | select PCI |
| 600 | select PLAT_ORION_LEGACY |
| 601 | help |
| 602 | Support for the following Marvell Orion 5x series SoCs: |
| 603 | Orion-1 (5181), Orion-VoIP (5181L), Orion-NAS (5182), |
| 604 | Orion-2 (5281), Orion-1-90 (6183). |
| 605 | |
| 606 | config ARCH_MMP |
| 607 | bool "Marvell PXA168/910/MMP2" |
| 608 | depends on MMU |
| 609 | select ARCH_REQUIRE_GPIOLIB |
| 610 | select CLKDEV_LOOKUP |
| 611 | select GENERIC_ALLOCATOR |
| 612 | select GENERIC_CLOCKEVENTS |
| 613 | select GPIO_PXA |
| 614 | select IRQ_DOMAIN |
| 615 | select NEED_MACH_GPIO_H |
| 616 | select PINCTRL |
| 617 | select PLAT_PXA |
| 618 | select SPARSE_IRQ |
| 619 | help |
| 620 | Support for Marvell's PXA168/PXA910(MMP) and MMP2 processor line. |
| 621 | |
| 622 | config ARCH_KS8695 |
| 623 | bool "Micrel/Kendin KS8695" |
| 624 | select ARCH_REQUIRE_GPIOLIB |
| 625 | select CLKSRC_MMIO |
| 626 | select CPU_ARM922T |
| 627 | select GENERIC_CLOCKEVENTS |
| 628 | select NEED_MACH_MEMORY_H |
| 629 | help |
| 630 | Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based |
| 631 | System-on-Chip devices. |
| 632 | |
| 633 | config ARCH_W90X900 |
| 634 | bool "Nuvoton W90X900 CPU" |
| 635 | select ARCH_REQUIRE_GPIOLIB |
| 636 | select CLKDEV_LOOKUP |
| 637 | select CLKSRC_MMIO |
| 638 | select CPU_ARM926T |
| 639 | select GENERIC_CLOCKEVENTS |
| 640 | help |
| 641 | Support for Nuvoton (Winbond logic dept.) ARM9 processor, |
| 642 | At present, the w90x900 has been renamed nuc900, regarding |
| 643 | the ARM series product line, you can login the following |
| 644 | link address to know more. |
| 645 | |
| 646 | <http://www.nuvoton.com/hq/enu/ProductAndSales/ProductLines/ |
| 647 | ConsumerElectronicsIC/ARMMicrocontroller/ARMMicrocontroller> |
| 648 | |
| 649 | config ARCH_LPC32XX |
| 650 | bool "NXP LPC32XX" |
| 651 | select ARCH_REQUIRE_GPIOLIB |
| 652 | select ARM_AMBA |
| 653 | select CLKDEV_LOOKUP |
| 654 | select CLKSRC_MMIO |
| 655 | select CPU_ARM926T |
| 656 | select GENERIC_CLOCKEVENTS |
| 657 | select HAVE_IDE |
| 658 | select HAVE_PWM |
| 659 | select USB_ARCH_HAS_OHCI |
| 660 | select USE_OF |
| 661 | help |
| 662 | Support for the NXP LPC32XX family of processors |
| 663 | |
| 664 | config ARCH_TEGRA |
| 665 | bool "NVIDIA Tegra" |
| 666 | select ARCH_HAS_CPUFREQ |
| 667 | select ARCH_REQUIRE_GPIOLIB |
| 668 | select CLKDEV_LOOKUP |
| 669 | select CLKSRC_MMIO |
| 670 | select CLKSRC_OF |
| 671 | select COMMON_CLK |
| 672 | select GENERIC_CLOCKEVENTS |
| 673 | select HAVE_CLK |
| 674 | select HAVE_SMP |
| 675 | select MIGHT_HAVE_CACHE_L2X0 |
| 676 | select SPARSE_IRQ |
| 677 | select USE_OF |
| 678 | help |
| 679 | This enables support for NVIDIA Tegra based systems (Tegra APX, |
| 680 | Tegra 6xx and Tegra 2 series). |
| 681 | |
| 682 | config ARCH_PXA |
| 683 | bool "PXA2xx/PXA3xx-based" |
| 684 | depends on MMU |
| 685 | select ARCH_HAS_CPUFREQ |
| 686 | select ARCH_MTD_XIP |
| 687 | select ARCH_REQUIRE_GPIOLIB |
| 688 | select ARM_CPU_SUSPEND if PM |
| 689 | select AUTO_ZRELADDR |
| 690 | select CLKDEV_LOOKUP |
| 691 | select CLKSRC_MMIO |
| 692 | select GENERIC_CLOCKEVENTS |
| 693 | select GPIO_PXA |
| 694 | select HAVE_IDE |
| 695 | select MULTI_IRQ_HANDLER |
| 696 | select NEED_MACH_GPIO_H |
| 697 | select PLAT_PXA |
| 698 | select SPARSE_IRQ |
| 699 | help |
| 700 | Support for Intel/Marvell's PXA2xx/PXA3xx processor line. |
| 701 | |
| 702 | config ARCH_MSM |
| 703 | bool "Qualcomm MSM" |
| 704 | select ARCH_REQUIRE_GPIOLIB |
| 705 | select CLKDEV_LOOKUP |
| 706 | select GENERIC_CLOCKEVENTS |
| 707 | select HAVE_CLK |
| 708 | help |
| 709 | Support for Qualcomm MSM/QSD based systems. This runs on the |
| 710 | apps processor of the MSM/QSD and depends on a shared memory |
| 711 | interface to the modem processor which runs the baseband |
| 712 | stack and controls some vital subsystems |
| 713 | (clock and power control, etc). |
| 714 | |
| 715 | config ARCH_SHMOBILE |
| 716 | bool "Renesas SH-Mobile / R-Mobile" |
| 717 | select CLKDEV_LOOKUP |
| 718 | select GENERIC_CLOCKEVENTS |
| 719 | select HAVE_CLK |
| 720 | select HAVE_MACH_CLKDEV |
| 721 | select HAVE_SMP |
| 722 | select MIGHT_HAVE_CACHE_L2X0 |
| 723 | select MULTI_IRQ_HANDLER |
| 724 | select NEED_MACH_MEMORY_H |
| 725 | select NO_IOPORT |
| 726 | select PINCTRL |
| 727 | select PM_GENERIC_DOMAINS if PM |
| 728 | select SPARSE_IRQ |
| 729 | help |
| 730 | Support for Renesas's SH-Mobile and R-Mobile ARM platforms. |
| 731 | |
| 732 | config ARCH_RPC |
| 733 | bool "RiscPC" |
| 734 | select ARCH_ACORN |
| 735 | select ARCH_MAY_HAVE_PC_FDC |
| 736 | select ARCH_SPARSEMEM_ENABLE |
| 737 | select ARCH_USES_GETTIMEOFFSET |
| 738 | select FIQ |
| 739 | select HAVE_IDE |
| 740 | select HAVE_PATA_PLATFORM |
| 741 | select ISA_DMA_API |
| 742 | select NEED_MACH_IO_H |
| 743 | select NEED_MACH_MEMORY_H |
| 744 | select NO_IOPORT |
| 745 | select VIRT_TO_BUS |
| 746 | help |
| 747 | On the Acorn Risc-PC, Linux can support the internal IDE disk and |
| 748 | CD-ROM interface, serial and parallel port, and the floppy drive. |
| 749 | |
| 750 | config ARCH_SA1100 |
| 751 | bool "SA1100-based" |
| 752 | select ARCH_HAS_CPUFREQ |
| 753 | select ARCH_MTD_XIP |
| 754 | select ARCH_REQUIRE_GPIOLIB |
| 755 | select ARCH_SPARSEMEM_ENABLE |
| 756 | select CLKDEV_LOOKUP |
| 757 | select CLKSRC_MMIO |
| 758 | select CPU_FREQ |
| 759 | select CPU_SA1100 |
| 760 | select GENERIC_CLOCKEVENTS |
| 761 | select HAVE_IDE |
| 762 | select ISA |
| 763 | select NEED_MACH_GPIO_H |
| 764 | select NEED_MACH_MEMORY_H |
| 765 | select SPARSE_IRQ |
| 766 | help |
| 767 | Support for StrongARM 11x0 based boards. |
| 768 | |
| 769 | config ARCH_S3C24XX |
| 770 | bool "Samsung S3C24XX SoCs" |
| 771 | select ARCH_HAS_CPUFREQ |
| 772 | select ARCH_USES_GETTIMEOFFSET |
| 773 | select CLKDEV_LOOKUP |
| 774 | select HAVE_CLK |
| 775 | select HAVE_S3C2410_I2C if I2C |
| 776 | select HAVE_S3C2410_WATCHDOG if WATCHDOG |
| 777 | select HAVE_S3C_RTC if RTC_CLASS |
| 778 | select NEED_MACH_GPIO_H |
| 779 | select NEED_MACH_IO_H |
| 780 | help |
| 781 | Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443 |
| 782 | and S3C2450 SoCs based systems, such as the Simtec Electronics BAST |
| 783 | (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or the |
| 784 | Samsung SMDK2410 development board (and derivatives). |
| 785 | |
| 786 | config ARCH_S3C64XX |
| 787 | bool "Samsung S3C64XX" |
| 788 | select ARCH_HAS_CPUFREQ |
| 789 | select ARCH_REQUIRE_GPIOLIB |
| 790 | select ARCH_USES_GETTIMEOFFSET |
| 791 | select ARM_VIC |
| 792 | select CLKDEV_LOOKUP |
| 793 | select CPU_V6 |
| 794 | select HAVE_CLK |
| 795 | select HAVE_S3C2410_I2C if I2C |
| 796 | select HAVE_S3C2410_WATCHDOG if WATCHDOG |
| 797 | select HAVE_TCM |
| 798 | select NEED_MACH_GPIO_H |
| 799 | select NO_IOPORT |
| 800 | select PLAT_SAMSUNG |
| 801 | select S3C_DEV_NAND |
| 802 | select S3C_GPIO_TRACK |
| 803 | select SAMSUNG_CLKSRC |
| 804 | select SAMSUNG_GPIOLIB_4BIT |
| 805 | select SAMSUNG_IRQ_VIC_TIMER |
| 806 | select USB_ARCH_HAS_OHCI |
| 807 | help |
| 808 | Samsung S3C64XX series based systems |
| 809 | |
| 810 | config ARCH_S5P64X0 |
| 811 | bool "Samsung S5P6440 S5P6450" |
| 812 | select CLKDEV_LOOKUP |
| 813 | select CLKSRC_MMIO |
| 814 | select CPU_V6 |
| 815 | select GENERIC_CLOCKEVENTS |
| 816 | select HAVE_CLK |
| 817 | select HAVE_S3C2410_I2C if I2C |
| 818 | select HAVE_S3C2410_WATCHDOG if WATCHDOG |
| 819 | select HAVE_S3C_RTC if RTC_CLASS |
| 820 | select NEED_MACH_GPIO_H |
| 821 | help |
| 822 | Samsung S5P64X0 CPU based systems, such as the Samsung SMDK6440, |
| 823 | SMDK6450. |
| 824 | |
| 825 | config ARCH_S5PC100 |
| 826 | bool "Samsung S5PC100" |
| 827 | select ARCH_USES_GETTIMEOFFSET |
| 828 | select CLKDEV_LOOKUP |
| 829 | select CPU_V7 |
| 830 | select HAVE_CLK |
| 831 | select HAVE_S3C2410_I2C if I2C |
| 832 | select HAVE_S3C2410_WATCHDOG if WATCHDOG |
| 833 | select HAVE_S3C_RTC if RTC_CLASS |
| 834 | select NEED_MACH_GPIO_H |
| 835 | help |
| 836 | Samsung S5PC100 series based systems |
| 837 | |
| 838 | config ARCH_S5PV210 |
| 839 | bool "Samsung S5PV210/S5PC110" |
| 840 | select ARCH_HAS_CPUFREQ |
| 841 | select ARCH_HAS_HOLES_MEMORYMODEL |
| 842 | select ARCH_SPARSEMEM_ENABLE |
| 843 | select CLKDEV_LOOKUP |
| 844 | select CLKSRC_MMIO |
| 845 | select CPU_V7 |
| 846 | select GENERIC_CLOCKEVENTS |
| 847 | select HAVE_CLK |
| 848 | select HAVE_S3C2410_I2C if I2C |
| 849 | select HAVE_S3C2410_WATCHDOG if WATCHDOG |
| 850 | select HAVE_S3C_RTC if RTC_CLASS |
| 851 | select NEED_MACH_GPIO_H |
| 852 | select NEED_MACH_MEMORY_H |
| 853 | help |
| 854 | Samsung S5PV210/S5PC110 series based systems |
| 855 | |
| 856 | config ARCH_EXYNOS |
| 857 | bool "Samsung EXYNOS" |
| 858 | select ARCH_HAS_CPUFREQ |
| 859 | select ARCH_HAS_HOLES_MEMORYMODEL |
| 860 | select ARCH_SPARSEMEM_ENABLE |
| 861 | select CLKDEV_LOOKUP |
| 862 | select CPU_V7 |
| 863 | select GENERIC_CLOCKEVENTS |
| 864 | select HAVE_CLK |
| 865 | select HAVE_S3C2410_I2C if I2C |
| 866 | select HAVE_S3C2410_WATCHDOG if WATCHDOG |
| 867 | select HAVE_S3C_RTC if RTC_CLASS |
| 868 | select NEED_MACH_GPIO_H |
| 869 | select NEED_MACH_MEMORY_H |
| 870 | help |
| 871 | Support for SAMSUNG's EXYNOS SoCs (EXYNOS4/5) |
| 872 | |
| 873 | config ARCH_SHARK |
| 874 | bool "Shark" |
| 875 | select ARCH_USES_GETTIMEOFFSET |
| 876 | select CPU_SA110 |
| 877 | select ISA |
| 878 | select ISA_DMA |
| 879 | select NEED_MACH_MEMORY_H |
| 880 | select PCI |
| 881 | select VIRT_TO_BUS |
| 882 | select ZONE_DMA |
| 883 | help |
| 884 | Support for the StrongARM based Digital DNARD machine, also known |
| 885 | as "Shark" (<http://www.shark-linux.de/shark.html>). |
| 886 | |
| 887 | config ARCH_U300 |
| 888 | bool "ST-Ericsson U300 Series" |
| 889 | depends on MMU |
| 890 | select ARCH_REQUIRE_GPIOLIB |
| 891 | select ARM_AMBA |
| 892 | select ARM_PATCH_PHYS_VIRT |
| 893 | select ARM_VIC |
| 894 | select CLKDEV_LOOKUP |
| 895 | select CLKSRC_MMIO |
| 896 | select COMMON_CLK |
| 897 | select CPU_ARM926T |
| 898 | select GENERIC_CLOCKEVENTS |
| 899 | select HAVE_TCM |
| 900 | select SPARSE_IRQ |
| 901 | help |
| 902 | Support for ST-Ericsson U300 series mobile platforms. |
| 903 | |
| 904 | config ARCH_U8500 |
| 905 | bool "ST-Ericsson U8500 Series" |
| 906 | depends on MMU |
| 907 | select ARCH_HAS_CPUFREQ |
| 908 | select ARCH_REQUIRE_GPIOLIB |
| 909 | select ARM_AMBA |
| 910 | select CLKDEV_LOOKUP |
| 911 | select CPU_V7 |
| 912 | select GENERIC_CLOCKEVENTS |
| 913 | select HAVE_SMP |
| 914 | select MIGHT_HAVE_CACHE_L2X0 |
| 915 | select SPARSE_IRQ |
| 916 | help |
| 917 | Support for ST-Ericsson's Ux500 architecture |
| 918 | |
| 919 | config ARCH_NOMADIK |
| 920 | bool "STMicroelectronics Nomadik" |
| 921 | select ARCH_REQUIRE_GPIOLIB |
| 922 | select ARM_AMBA |
| 923 | select ARM_VIC |
| 924 | select CLKSRC_NOMADIK_MTU |
| 925 | select COMMON_CLK |
| 926 | select CPU_ARM926T |
| 927 | select GENERIC_CLOCKEVENTS |
| 928 | select MIGHT_HAVE_CACHE_L2X0 |
| 929 | select USE_OF |
| 930 | select PINCTRL |
| 931 | select PINCTRL_STN8815 |
| 932 | select SPARSE_IRQ |
| 933 | help |
| 934 | Support for the Nomadik platform by ST-Ericsson |
| 935 | |
| 936 | config PLAT_SPEAR |
| 937 | bool "ST SPEAr" |
| 938 | select ARCH_HAS_CPUFREQ |
| 939 | select ARCH_REQUIRE_GPIOLIB |
| 940 | select ARM_AMBA |
| 941 | select CLKDEV_LOOKUP |
| 942 | select CLKSRC_MMIO |
| 943 | select COMMON_CLK |
| 944 | select GENERIC_CLOCKEVENTS |
| 945 | select HAVE_CLK |
| 946 | help |
| 947 | Support for ST's SPEAr platform (SPEAr3xx, SPEAr6xx and SPEAr13xx). |
| 948 | |
| 949 | config ARCH_DAVINCI |
| 950 | bool "TI DaVinci" |
| 951 | select ARCH_HAS_HOLES_MEMORYMODEL |
| 952 | select ARCH_REQUIRE_GPIOLIB |
| 953 | select CLKDEV_LOOKUP |
| 954 | select GENERIC_ALLOCATOR |
| 955 | select GENERIC_CLOCKEVENTS |
| 956 | select GENERIC_IRQ_CHIP |
| 957 | select HAVE_IDE |
| 958 | select NEED_MACH_GPIO_H |
| 959 | select USE_OF |
| 960 | select ZONE_DMA |
| 961 | help |
| 962 | Support for TI's DaVinci platform. |
| 963 | |
| 964 | config ARCH_OMAP1 |
| 965 | bool "TI OMAP1" |
| 966 | depends on MMU |
| 967 | select ARCH_HAS_CPUFREQ |
| 968 | select ARCH_HAS_HOLES_MEMORYMODEL |
| 969 | select ARCH_OMAP |
| 970 | select ARCH_REQUIRE_GPIOLIB |
| 971 | select CLKDEV_LOOKUP |
| 972 | select CLKSRC_MMIO |
| 973 | select GENERIC_CLOCKEVENTS |
| 974 | select GENERIC_IRQ_CHIP |
| 975 | select HAVE_CLK |
| 976 | select HAVE_IDE |
| 977 | select IRQ_DOMAIN |
| 978 | select NEED_MACH_IO_H if PCCARD |
| 979 | select NEED_MACH_MEMORY_H |
| 980 | help |
| 981 | Support for older TI OMAP1 (omap7xx, omap15xx or omap16xx) |
| 982 | |
| 983 | endchoice |
| 984 | |
| 985 | menu "Multiple platform selection" |
| 986 | depends on ARCH_MULTIPLATFORM |
| 987 | |
| 988 | comment "CPU Core family selection" |
| 989 | |
| 990 | config ARCH_MULTI_V4 |
| 991 | bool "ARMv4 based platforms (FA526, StrongARM)" |
| 992 | depends on !ARCH_MULTI_V6_V7 |
| 993 | select ARCH_MULTI_V4_V5 |
| 994 | |
| 995 | config ARCH_MULTI_V4T |
| 996 | bool "ARMv4T based platforms (ARM720T, ARM920T, ...)" |
| 997 | depends on !ARCH_MULTI_V6_V7 |
| 998 | select ARCH_MULTI_V4_V5 |
| 999 | |
| 1000 | config ARCH_MULTI_V5 |
| 1001 | bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)" |
| 1002 | depends on !ARCH_MULTI_V6_V7 |
| 1003 | select ARCH_MULTI_V4_V5 |
| 1004 | |
| 1005 | config ARCH_MULTI_V4_V5 |
| 1006 | bool |
| 1007 | |
| 1008 | config ARCH_MULTI_V6 |
| 1009 | bool "ARMv6 based platforms (ARM11)" |
| 1010 | select ARCH_MULTI_V6_V7 |
| 1011 | select CPU_V6 |
| 1012 | |
| 1013 | config ARCH_MULTI_V7 |
| 1014 | bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)" |
| 1015 | default y |
| 1016 | select ARCH_MULTI_V6_V7 |
| 1017 | select ARCH_VEXPRESS |
| 1018 | select CPU_V7 |
| 1019 | |
| 1020 | config ARCH_MULTI_V6_V7 |
| 1021 | bool |
| 1022 | |
| 1023 | config ARCH_MULTI_CPU_AUTO |
| 1024 | def_bool !(ARCH_MULTI_V4 || ARCH_MULTI_V4T || ARCH_MULTI_V6_V7) |
| 1025 | select ARCH_MULTI_V5 |
| 1026 | |
| 1027 | endmenu |
| 1028 | |
| 1029 | # |
| 1030 | # This is sorted alphabetically by mach-* pathname. However, plat-* |
| 1031 | # Kconfigs may be included either alphabetically (according to the |
| 1032 | # plat- suffix) or along side the corresponding mach-* source. |
| 1033 | # |
| 1034 | source "arch/arm/mach-mvebu/Kconfig" |
| 1035 | |
| 1036 | source "arch/arm/mach-at91/Kconfig" |
| 1037 | |
| 1038 | source "arch/arm/mach-bcm/Kconfig" |
| 1039 | |
| 1040 | source "arch/arm/mach-clps711x/Kconfig" |
| 1041 | |
| 1042 | source "arch/arm/mach-cns3xxx/Kconfig" |
| 1043 | |
| 1044 | source "arch/arm/mach-davinci/Kconfig" |
| 1045 | |
| 1046 | source "arch/arm/mach-dove/Kconfig" |
| 1047 | |
| 1048 | source "arch/arm/mach-ep93xx/Kconfig" |
| 1049 | |
| 1050 | source "arch/arm/mach-footbridge/Kconfig" |
| 1051 | |
| 1052 | source "arch/arm/mach-gemini/Kconfig" |
| 1053 | |
| 1054 | source "arch/arm/mach-h720x/Kconfig" |
| 1055 | |
| 1056 | source "arch/arm/mach-highbank/Kconfig" |
| 1057 | |
| 1058 | source "arch/arm/mach-integrator/Kconfig" |
| 1059 | |
| 1060 | source "arch/arm/mach-iop32x/Kconfig" |
| 1061 | |
| 1062 | source "arch/arm/mach-iop33x/Kconfig" |
| 1063 | |
| 1064 | source "arch/arm/mach-iop13xx/Kconfig" |
| 1065 | |
| 1066 | source "arch/arm/mach-ixp4xx/Kconfig" |
| 1067 | |
| 1068 | source "arch/arm/mach-kirkwood/Kconfig" |
| 1069 | |
| 1070 | source "arch/arm/mach-ks8695/Kconfig" |
| 1071 | |
| 1072 | source "arch/arm/mach-msm/Kconfig" |
| 1073 | |
| 1074 | source "arch/arm/mach-mv78xx0/Kconfig" |
| 1075 | |
| 1076 | source "arch/arm/mach-imx/Kconfig" |
| 1077 | |
| 1078 | source "arch/arm/mach-mxs/Kconfig" |
| 1079 | |
| 1080 | source "arch/arm/mach-netx/Kconfig" |
| 1081 | |
| 1082 | source "arch/arm/mach-nomadik/Kconfig" |
| 1083 | |
| 1084 | source "arch/arm/plat-omap/Kconfig" |
| 1085 | |
| 1086 | source "arch/arm/mach-omap1/Kconfig" |
| 1087 | |
| 1088 | source "arch/arm/mach-omap2/Kconfig" |
| 1089 | |
| 1090 | source "arch/arm/mach-orion5x/Kconfig" |
| 1091 | |
| 1092 | source "arch/arm/mach-picoxcell/Kconfig" |
| 1093 | |
| 1094 | source "arch/arm/mach-pxa/Kconfig" |
| 1095 | source "arch/arm/plat-pxa/Kconfig" |
| 1096 | |
| 1097 | source "arch/arm/mach-mmp/Kconfig" |
| 1098 | |
| 1099 | source "arch/arm/mach-realview/Kconfig" |
| 1100 | |
| 1101 | source "arch/arm/mach-sa1100/Kconfig" |
| 1102 | |
| 1103 | source "arch/arm/plat-samsung/Kconfig" |
| 1104 | |
| 1105 | source "arch/arm/mach-socfpga/Kconfig" |
| 1106 | |
| 1107 | source "arch/arm/plat-spear/Kconfig" |
| 1108 | |
| 1109 | source "arch/arm/mach-s3c24xx/Kconfig" |
| 1110 | |
| 1111 | if ARCH_S3C64XX |
| 1112 | source "arch/arm/mach-s3c64xx/Kconfig" |
| 1113 | endif |
| 1114 | |
| 1115 | source "arch/arm/mach-s5p64x0/Kconfig" |
| 1116 | |
| 1117 | source "arch/arm/mach-s5pc100/Kconfig" |
| 1118 | |
| 1119 | source "arch/arm/mach-s5pv210/Kconfig" |
| 1120 | |
| 1121 | source "arch/arm/mach-exynos/Kconfig" |
| 1122 | |
| 1123 | source "arch/arm/mach-shmobile/Kconfig" |
| 1124 | |
| 1125 | source "arch/arm/mach-sunxi/Kconfig" |
| 1126 | |
| 1127 | source "arch/arm/mach-prima2/Kconfig" |
| 1128 | |
| 1129 | source "arch/arm/mach-tegra/Kconfig" |
| 1130 | |
| 1131 | source "arch/arm/mach-u300/Kconfig" |
| 1132 | |
| 1133 | source "arch/arm/mach-ux500/Kconfig" |
| 1134 | |
| 1135 | source "arch/arm/mach-versatile/Kconfig" |
| 1136 | |
| 1137 | source "arch/arm/mach-vexpress/Kconfig" |
| 1138 | source "arch/arm/plat-versatile/Kconfig" |
| 1139 | |
| 1140 | source "arch/arm/mach-virt/Kconfig" |
| 1141 | |
| 1142 | source "arch/arm/mach-vt8500/Kconfig" |
| 1143 | |
| 1144 | source "arch/arm/mach-w90x900/Kconfig" |
| 1145 | |
| 1146 | source "arch/arm/mach-zynq/Kconfig" |
| 1147 | |
| 1148 | # Definitions to make life easier |
| 1149 | config ARCH_ACORN |
| 1150 | bool |
| 1151 | |
| 1152 | config PLAT_IOP |
| 1153 | bool |
| 1154 | select GENERIC_CLOCKEVENTS |
| 1155 | |
| 1156 | config PLAT_ORION |
| 1157 | bool |
| 1158 | select CLKSRC_MMIO |
| 1159 | select COMMON_CLK |
| 1160 | select GENERIC_IRQ_CHIP |
| 1161 | select IRQ_DOMAIN |
| 1162 | |
| 1163 | config PLAT_ORION_LEGACY |
| 1164 | bool |
| 1165 | select PLAT_ORION |
| 1166 | |
| 1167 | config PLAT_PXA |
| 1168 | bool |
| 1169 | |
| 1170 | config PLAT_VERSATILE |
| 1171 | bool |
| 1172 | |
| 1173 | config ARM_TIMER_SP804 |
| 1174 | bool |
| 1175 | select CLKSRC_MMIO |
| 1176 | select HAVE_SCHED_CLOCK |
| 1177 | |
| 1178 | source arch/arm/mm/Kconfig |
| 1179 | |
| 1180 | config ARM_NR_BANKS |
| 1181 | int |
| 1182 | default 16 if ARCH_EP93XX |
| 1183 | default 8 |
| 1184 | |
| 1185 | config IWMMXT |
| 1186 | bool "Enable iWMMXt support" |
| 1187 | depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4 |
| 1188 | default y if PXA27x || PXA3xx || ARCH_MMP |
| 1189 | help |
| 1190 | Enable support for iWMMXt context switching at run time if |
| 1191 | running on a CPU that supports it. |
| 1192 | |
| 1193 | config XSCALE_PMU |
| 1194 | bool |
| 1195 | depends on CPU_XSCALE |
| 1196 | default y |
| 1197 | |
| 1198 | config MULTI_IRQ_HANDLER |
| 1199 | bool |
| 1200 | help |
| 1201 | Allow each machine to specify it's own IRQ handler at run time. |
| 1202 | |
| 1203 | if !MMU |
| 1204 | source "arch/arm/Kconfig-nommu" |
| 1205 | endif |
| 1206 | |
| 1207 | config ARM_ERRATA_326103 |
| 1208 | bool "ARM errata: FSR write bit incorrect on a SWP to read-only memory" |
| 1209 | depends on CPU_V6 |
| 1210 | help |
| 1211 | Executing a SWP instruction to read-only memory does not set bit 11 |
| 1212 | of the FSR on the ARM 1136 prior to r1p0. This causes the kernel to |
| 1213 | treat the access as a read, preventing a COW from occurring and |
| 1214 | causing the faulting task to livelock. |
| 1215 | |
| 1216 | config ARM_ERRATA_411920 |
| 1217 | bool "ARM errata: Invalidation of the Instruction Cache operation can fail" |
| 1218 | depends on CPU_V6 || CPU_V6K |
| 1219 | help |
| 1220 | Invalidation of the Instruction Cache operation can |
| 1221 | fail. This erratum is present in 1136 (before r1p4), 1156 and 1176. |
| 1222 | It does not affect the MPCore. This option enables the ARM Ltd. |
| 1223 | recommended workaround. |
| 1224 | |
| 1225 | config ARM_ERRATA_430973 |
| 1226 | bool "ARM errata: Stale prediction on replaced interworking branch" |
| 1227 | depends on CPU_V7 |
| 1228 | help |
| 1229 | This option enables the workaround for the 430973 Cortex-A8 |
| 1230 | (r1p0..r1p2) erratum. If a code sequence containing an ARM/Thumb |
| 1231 | interworking branch is replaced with another code sequence at the |
| 1232 | same virtual address, whether due to self-modifying code or virtual |
| 1233 | to physical address re-mapping, Cortex-A8 does not recover from the |
| 1234 | stale interworking branch prediction. This results in Cortex-A8 |
| 1235 | executing the new code sequence in the incorrect ARM or Thumb state. |
| 1236 | The workaround enables the BTB/BTAC operations by setting ACTLR.IBE |
| 1237 | and also flushes the branch target cache at every context switch. |
| 1238 | Note that setting specific bits in the ACTLR register may not be |
| 1239 | available in non-secure mode. |
| 1240 | |
| 1241 | config ARM_ERRATA_458693 |
| 1242 | bool "ARM errata: Processor deadlock when a false hazard is created" |
| 1243 | depends on CPU_V7 |
| 1244 | depends on !ARCH_MULTIPLATFORM |
| 1245 | help |
| 1246 | This option enables the workaround for the 458693 Cortex-A8 (r2p0) |
| 1247 | erratum. For very specific sequences of memory operations, it is |
| 1248 | possible for a hazard condition intended for a cache line to instead |
| 1249 | be incorrectly associated with a different cache line. This false |
| 1250 | hazard might then cause a processor deadlock. The workaround enables |
| 1251 | the L1 caching of the NEON accesses and disables the PLD instruction |
| 1252 | in the ACTLR register. Note that setting specific bits in the ACTLR |
| 1253 | register may not be available in non-secure mode. |
| 1254 | |
| 1255 | config ARM_ERRATA_460075 |
| 1256 | bool "ARM errata: Data written to the L2 cache can be overwritten with stale data" |
| 1257 | depends on CPU_V7 |
| 1258 | depends on !ARCH_MULTIPLATFORM |
| 1259 | help |
| 1260 | This option enables the workaround for the 460075 Cortex-A8 (r2p0) |
| 1261 | erratum. Any asynchronous access to the L2 cache may encounter a |
| 1262 | situation in which recent store transactions to the L2 cache are lost |
| 1263 | and overwritten with stale memory contents from external memory. The |
| 1264 | workaround disables the write-allocate mode for the L2 cache via the |
| 1265 | ACTLR register. Note that setting specific bits in the ACTLR register |
| 1266 | may not be available in non-secure mode. |
| 1267 | |
| 1268 | config ARM_ERRATA_742230 |
| 1269 | bool "ARM errata: DMB operation may be faulty" |
| 1270 | depends on CPU_V7 && SMP |
| 1271 | depends on !ARCH_MULTIPLATFORM |
| 1272 | help |
| 1273 | This option enables the workaround for the 742230 Cortex-A9 |
| 1274 | (r1p0..r2p2) erratum. Under rare circumstances, a DMB instruction |
| 1275 | between two write operations may not ensure the correct visibility |
| 1276 | ordering of the two writes. This workaround sets a specific bit in |
| 1277 | the diagnostic register of the Cortex-A9 which causes the DMB |
| 1278 | instruction to behave as a DSB, ensuring the correct behaviour of |
| 1279 | the two writes. |
| 1280 | |
| 1281 | config ARM_ERRATA_742231 |
| 1282 | bool "ARM errata: Incorrect hazard handling in the SCU may lead to data corruption" |
| 1283 | depends on CPU_V7 && SMP |
| 1284 | depends on !ARCH_MULTIPLATFORM |
| 1285 | help |
| 1286 | This option enables the workaround for the 742231 Cortex-A9 |
| 1287 | (r2p0..r2p2) erratum. Under certain conditions, specific to the |
| 1288 | Cortex-A9 MPCore micro-architecture, two CPUs working in SMP mode, |
| 1289 | accessing some data located in the same cache line, may get corrupted |
| 1290 | data due to bad handling of the address hazard when the line gets |
| 1291 | replaced from one of the CPUs at the same time as another CPU is |
| 1292 | accessing it. This workaround sets specific bits in the diagnostic |
| 1293 | register of the Cortex-A9 which reduces the linefill issuing |
| 1294 | capabilities of the processor. |
| 1295 | |
| 1296 | config PL310_ERRATA_588369 |
| 1297 | bool "PL310 errata: Clean & Invalidate maintenance operations do not invalidate clean lines" |
| 1298 | depends on CACHE_L2X0 |
| 1299 | help |
| 1300 | The PL310 L2 cache controller implements three types of Clean & |
| 1301 | Invalidate maintenance operations: by Physical Address |
| 1302 | (offset 0x7F0), by Index/Way (0x7F8) and by Way (0x7FC). |
| 1303 | They are architecturally defined to behave as the execution of a |
| 1304 | clean operation followed immediately by an invalidate operation, |
| 1305 | both performing to the same memory location. This functionality |
| 1306 | is not correctly implemented in PL310 as clean lines are not |
| 1307 | invalidated as a result of these operations. |
| 1308 | |
| 1309 | config ARM_ERRATA_720789 |
| 1310 | bool "ARM errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID" |
| 1311 | depends on CPU_V7 |
| 1312 | help |
| 1313 | This option enables the workaround for the 720789 Cortex-A9 (prior to |
| 1314 | r2p0) erratum. A faulty ASID can be sent to the other CPUs for the |
| 1315 | broadcasted CP15 TLB maintenance operations TLBIASIDIS and TLBIMVAIS. |
| 1316 | As a consequence of this erratum, some TLB entries which should be |
| 1317 | invalidated are not, resulting in an incoherency in the system page |
| 1318 | tables. The workaround changes the TLB flushing routines to invalidate |
| 1319 | entries regardless of the ASID. |
| 1320 | |
| 1321 | config PL310_ERRATA_727915 |
| 1322 | bool "PL310 errata: Background Clean & Invalidate by Way operation can cause data corruption" |
| 1323 | depends on CACHE_L2X0 |
| 1324 | help |
| 1325 | PL310 implements the Clean & Invalidate by Way L2 cache maintenance |
| 1326 | operation (offset 0x7FC). This operation runs in background so that |
| 1327 | PL310 can handle normal accesses while it is in progress. Under very |
| 1328 | rare circumstances, due to this erratum, write data can be lost when |
| 1329 | PL310 treats a cacheable write transaction during a Clean & |
| 1330 | Invalidate by Way operation. |
| 1331 | |
| 1332 | config ARM_ERRATA_743622 |
| 1333 | bool "ARM errata: Faulty hazard checking in the Store Buffer may lead to data corruption" |
| 1334 | depends on CPU_V7 |
| 1335 | depends on !ARCH_MULTIPLATFORM |
| 1336 | help |
| 1337 | This option enables the workaround for the 743622 Cortex-A9 |
| 1338 | (r2p*) erratum. Under very rare conditions, a faulty |
| 1339 | optimisation in the Cortex-A9 Store Buffer may lead to data |
| 1340 | corruption. This workaround sets a specific bit in the diagnostic |
| 1341 | register of the Cortex-A9 which disables the Store Buffer |
| 1342 | optimisation, preventing the defect from occurring. This has no |
| 1343 | visible impact on the overall performance or power consumption of the |
| 1344 | processor. |
| 1345 | |
| 1346 | config ARM_ERRATA_751472 |
| 1347 | bool "ARM errata: Interrupted ICIALLUIS may prevent completion of broadcasted operation" |
| 1348 | depends on CPU_V7 |
| 1349 | depends on !ARCH_MULTIPLATFORM |
| 1350 | help |
| 1351 | This option enables the workaround for the 751472 Cortex-A9 (prior |
| 1352 | to r3p0) erratum. An interrupted ICIALLUIS operation may prevent the |
| 1353 | completion of a following broadcasted operation if the second |
| 1354 | operation is received by a CPU before the ICIALLUIS has completed, |
| 1355 | potentially leading to corrupted entries in the cache or TLB. |
| 1356 | |
| 1357 | config PL310_ERRATA_753970 |
| 1358 | bool "PL310 errata: cache sync operation may be faulty" |
| 1359 | depends on CACHE_PL310 |
| 1360 | help |
| 1361 | This option enables the workaround for the 753970 PL310 (r3p0) erratum. |
| 1362 | |
| 1363 | Under some condition the effect of cache sync operation on |
| 1364 | the store buffer still remains when the operation completes. |
| 1365 | This means that the store buffer is always asked to drain and |
| 1366 | this prevents it from merging any further writes. The workaround |
| 1367 | is to replace the normal offset of cache sync operation (0x730) |
| 1368 | by another offset targeting an unmapped PL310 register 0x740. |
| 1369 | This has the same effect as the cache sync operation: store buffer |
| 1370 | drain and waiting for all buffers empty. |
| 1371 | |
| 1372 | config ARM_ERRATA_754322 |
| 1373 | bool "ARM errata: possible faulty MMU translations following an ASID switch" |
| 1374 | depends on CPU_V7 |
| 1375 | help |
| 1376 | This option enables the workaround for the 754322 Cortex-A9 (r2p*, |
| 1377 | r3p*) erratum. A speculative memory access may cause a page table walk |
| 1378 | which starts prior to an ASID switch but completes afterwards. This |
| 1379 | can populate the micro-TLB with a stale entry which may be hit with |
| 1380 | the new ASID. This workaround places two dsb instructions in the mm |
| 1381 | switching code so that no page table walks can cross the ASID switch. |
| 1382 | |
| 1383 | config ARM_ERRATA_754327 |
| 1384 | bool "ARM errata: no automatic Store Buffer drain" |
| 1385 | depends on CPU_V7 && SMP |
| 1386 | help |
| 1387 | This option enables the workaround for the 754327 Cortex-A9 (prior to |
| 1388 | r2p0) erratum. The Store Buffer does not have any automatic draining |
| 1389 | mechanism and therefore a livelock may occur if an external agent |
| 1390 | continuously polls a memory location waiting to observe an update. |
| 1391 | This workaround defines cpu_relax() as smp_mb(), preventing correctly |
| 1392 | written polling loops from denying visibility of updates to memory. |
| 1393 | |
| 1394 | config ARM_ERRATA_364296 |
| 1395 | bool "ARM errata: Possible cache data corruption with hit-under-miss enabled" |
| 1396 | depends on CPU_V6 && !SMP |
| 1397 | help |
| 1398 | This options enables the workaround for the 364296 ARM1136 |
| 1399 | r0p2 erratum (possible cache data corruption with |
| 1400 | hit-under-miss enabled). It sets the undocumented bit 31 in |
| 1401 | the auxiliary control register and the FI bit in the control |
| 1402 | register, thus disabling hit-under-miss without putting the |
| 1403 | processor into full low interrupt latency mode. ARM11MPCore |
| 1404 | is not affected. |
| 1405 | |
| 1406 | config ARM_ERRATA_764369 |
| 1407 | bool "ARM errata: Data cache line maintenance operation by MVA may not succeed" |
| 1408 | depends on CPU_V7 && SMP |
| 1409 | help |
| 1410 | This option enables the workaround for erratum 764369 |
| 1411 | affecting Cortex-A9 MPCore with two or more processors (all |
| 1412 | current revisions). Under certain timing circumstances, a data |
| 1413 | cache line maintenance operation by MVA targeting an Inner |
| 1414 | Shareable memory region may fail to proceed up to either the |
| 1415 | Point of Coherency or to the Point of Unification of the |
| 1416 | system. This workaround adds a DSB instruction before the |
| 1417 | relevant cache maintenance functions and sets a specific bit |
| 1418 | in the diagnostic control register of the SCU. |
| 1419 | |
| 1420 | config PL310_ERRATA_769419 |
| 1421 | bool "PL310 errata: no automatic Store Buffer drain" |
| 1422 | depends on CACHE_L2X0 |
| 1423 | help |
| 1424 | On revisions of the PL310 prior to r3p2, the Store Buffer does |
| 1425 | not automatically drain. This can cause normal, non-cacheable |
| 1426 | writes to be retained when the memory system is idle, leading |
| 1427 | to suboptimal I/O performance for drivers using coherent DMA. |
| 1428 | This option adds a write barrier to the cpu_idle loop so that, |
| 1429 | on systems with an outer cache, the store buffer is drained |
| 1430 | explicitly. |
| 1431 | |
| 1432 | config ARM_ERRATA_775420 |
| 1433 | bool "ARM errata: A data cache maintenance operation which aborts, might lead to deadlock" |
| 1434 | depends on CPU_V7 |
| 1435 | help |
| 1436 | This option enables the workaround for the 775420 Cortex-A9 (r2p2, |
| 1437 | r2p6,r2p8,r2p10,r3p0) erratum. In case a date cache maintenance |
| 1438 | operation aborts with MMU exception, it might cause the processor |
| 1439 | to deadlock. This workaround puts DSB before executing ISB if |
| 1440 | an abort may occur on cache maintenance. |
| 1441 | |
| 1442 | endmenu |
| 1443 | |
| 1444 | source "arch/arm/common/Kconfig" |
| 1445 | |
| 1446 | menu "Bus support" |
| 1447 | |
| 1448 | config ARM_AMBA |
| 1449 | bool |
| 1450 | |
| 1451 | config ISA |
| 1452 | bool |
| 1453 | help |
| 1454 | Find out whether you have ISA slots on your motherboard. ISA is the |
| 1455 | name of a bus system, i.e. the way the CPU talks to the other stuff |
| 1456 | inside your box. Other bus systems are PCI, EISA, MicroChannel |
| 1457 | (MCA) or VESA. ISA is an older system, now being displaced by PCI; |
| 1458 | newer boards don't support it. If you have ISA, say Y, otherwise N. |
| 1459 | |
| 1460 | # Select ISA DMA controller support |
| 1461 | config ISA_DMA |
| 1462 | bool |
| 1463 | select ISA_DMA_API |
| 1464 | |
| 1465 | # Select ISA DMA interface |
| 1466 | config ISA_DMA_API |
| 1467 | bool |
| 1468 | |
| 1469 | config PCI |
| 1470 | bool "PCI support" if MIGHT_HAVE_PCI |
| 1471 | help |
| 1472 | Find out whether you have a PCI motherboard. PCI is the name of a |
| 1473 | bus system, i.e. the way the CPU talks to the other stuff inside |
| 1474 | your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or |
| 1475 | VESA. If you have PCI, say Y, otherwise N. |
| 1476 | |
| 1477 | config PCI_DOMAINS |
| 1478 | bool |
| 1479 | depends on PCI |
| 1480 | |
| 1481 | config PCI_NANOENGINE |
| 1482 | bool "BSE nanoEngine PCI support" |
| 1483 | depends on SA1100_NANOENGINE |
| 1484 | help |
| 1485 | Enable PCI on the BSE nanoEngine board. |
| 1486 | |
| 1487 | config PCI_SYSCALL |
| 1488 | def_bool PCI |
| 1489 | |
| 1490 | # Select the host bridge type |
| 1491 | config PCI_HOST_VIA82C505 |
| 1492 | bool |
| 1493 | depends on PCI && ARCH_SHARK |
| 1494 | default y |
| 1495 | |
| 1496 | config PCI_HOST_ITE8152 |
| 1497 | bool |
| 1498 | depends on PCI && MACH_ARMCORE |
| 1499 | default y |
| 1500 | select DMABOUNCE |
| 1501 | |
| 1502 | source "drivers/pci/Kconfig" |
| 1503 | |
| 1504 | source "drivers/pcmcia/Kconfig" |
| 1505 | |
| 1506 | endmenu |
| 1507 | |
| 1508 | menu "Kernel Features" |
| 1509 | |
| 1510 | config HAVE_SMP |
| 1511 | bool |
| 1512 | help |
| 1513 | This option should be selected by machines which have an SMP- |
| 1514 | capable CPU. |
| 1515 | |
| 1516 | The only effect of this option is to make the SMP-related |
| 1517 | options available to the user for configuration. |
| 1518 | |
| 1519 | config SMP |
| 1520 | bool "Symmetric Multi-Processing" |
| 1521 | depends on CPU_V6K || CPU_V7 |
| 1522 | depends on GENERIC_CLOCKEVENTS |
| 1523 | depends on HAVE_SMP |
| 1524 | depends on MMU |
| 1525 | select HAVE_ARM_SCU if !ARCH_MSM_SCORPIONMP |
| 1526 | select USE_GENERIC_SMP_HELPERS |
| 1527 | help |
| 1528 | This enables support for systems with more than one CPU. If you have |
| 1529 | a system with only one CPU, like most personal computers, say N. If |
| 1530 | you have a system with more than one CPU, say Y. |
| 1531 | |
| 1532 | If you say N here, the kernel will run on single and multiprocessor |
| 1533 | machines, but will use only one CPU of a multiprocessor machine. If |
| 1534 | you say Y here, the kernel will run on many, but not all, single |
| 1535 | processor machines. On a single processor machine, the kernel will |
| 1536 | run faster if you say N here. |
| 1537 | |
| 1538 | See also <file:Documentation/x86/i386/IO-APIC.txt>, |
| 1539 | <file:Documentation/nmi_watchdog.txt> and the SMP-HOWTO available at |
| 1540 | <http://tldp.org/HOWTO/SMP-HOWTO.html>. |
| 1541 | |
| 1542 | If you don't know what to do here, say N. |
| 1543 | |
| 1544 | config SMP_ON_UP |
| 1545 | bool "Allow booting SMP kernel on uniprocessor systems (EXPERIMENTAL)" |
| 1546 | depends on SMP && !XIP_KERNEL |
| 1547 | default y |
| 1548 | help |
| 1549 | SMP kernels contain instructions which fail on non-SMP processors. |
| 1550 | Enabling this option allows the kernel to modify itself to make |
| 1551 | these instructions safe. Disabling it allows about 1K of space |
| 1552 | savings. |
| 1553 | |
| 1554 | If you don't know what to do here, say Y. |
| 1555 | |
| 1556 | config ARM_CPU_TOPOLOGY |
| 1557 | bool "Support cpu topology definition" |
| 1558 | depends on SMP && CPU_V7 |
| 1559 | default y |
| 1560 | help |
| 1561 | Support ARM cpu topology definition. The MPIDR register defines |
| 1562 | affinity between processors which is then used to describe the cpu |
| 1563 | topology of an ARM System. |
| 1564 | |
| 1565 | config SCHED_MC |
| 1566 | bool "Multi-core scheduler support" |
| 1567 | depends on ARM_CPU_TOPOLOGY |
| 1568 | help |
| 1569 | Multi-core scheduler support improves the CPU scheduler's decision |
| 1570 | making when dealing with multi-core CPU chips at a cost of slightly |
| 1571 | increased overhead in some places. If unsure say N here. |
| 1572 | |
| 1573 | config SCHED_SMT |
| 1574 | bool "SMT scheduler support" |
| 1575 | depends on ARM_CPU_TOPOLOGY |
| 1576 | help |
| 1577 | Improves the CPU scheduler's decision making when dealing with |
| 1578 | MultiThreading at a cost of slightly increased overhead in some |
| 1579 | places. If unsure say N here. |
| 1580 | |
| 1581 | config HAVE_ARM_SCU |
| 1582 | bool |
| 1583 | help |
| 1584 | This option enables support for the ARM system coherency unit |
| 1585 | |
| 1586 | config HAVE_ARM_ARCH_TIMER |
| 1587 | bool "Architected timer support" |
| 1588 | depends on CPU_V7 |
| 1589 | select ARM_ARCH_TIMER |
| 1590 | help |
| 1591 | This option enables support for the ARM architected timer |
| 1592 | |
| 1593 | config HAVE_ARM_TWD |
| 1594 | bool |
| 1595 | depends on SMP |
| 1596 | help |
| 1597 | This options enables support for the ARM timer and watchdog unit |
| 1598 | |
| 1599 | choice |
| 1600 | prompt "Memory split" |
| 1601 | default VMSPLIT_3G |
| 1602 | help |
| 1603 | Select the desired split between kernel and user memory. |
| 1604 | |
| 1605 | If you are not absolutely sure what you are doing, leave this |
| 1606 | option alone! |
| 1607 | |
| 1608 | config VMSPLIT_3G |
| 1609 | bool "3G/1G user/kernel split" |
| 1610 | config VMSPLIT_2G |
| 1611 | bool "2G/2G user/kernel split" |
| 1612 | config VMSPLIT_1G |
| 1613 | bool "1G/3G user/kernel split" |
| 1614 | endchoice |
| 1615 | |
| 1616 | config PAGE_OFFSET |
| 1617 | hex |
| 1618 | default 0x40000000 if VMSPLIT_1G |
| 1619 | default 0x80000000 if VMSPLIT_2G |
| 1620 | default 0xC0000000 |
| 1621 | |
| 1622 | config NR_CPUS |
| 1623 | int "Maximum number of CPUs (2-32)" |
| 1624 | range 2 32 |
| 1625 | depends on SMP |
| 1626 | default "4" |
| 1627 | |
| 1628 | config HOTPLUG_CPU |
| 1629 | bool "Support for hot-pluggable CPUs" |
| 1630 | depends on SMP && HOTPLUG |
| 1631 | help |
| 1632 | Say Y here to experiment with turning CPUs off and on. CPUs |
| 1633 | can be controlled through /sys/devices/system/cpu. |
| 1634 | |
| 1635 | config ARM_PSCI |
| 1636 | bool "Support for the ARM Power State Coordination Interface (PSCI)" |
| 1637 | depends on CPU_V7 |
| 1638 | help |
| 1639 | Say Y here if you want Linux to communicate with system firmware |
| 1640 | implementing the PSCI specification for CPU-centric power |
| 1641 | management operations described in ARM document number ARM DEN |
| 1642 | 0022A ("Power State Coordination Interface System Software on |
| 1643 | ARM processors"). |
| 1644 | |
| 1645 | config LOCAL_TIMERS |
| 1646 | bool "Use local timer interrupts" |
| 1647 | depends on SMP |
| 1648 | default y |
| 1649 | select HAVE_ARM_TWD if (!ARCH_MSM_SCORPIONMP && !EXYNOS4_MCT) |
| 1650 | help |
| 1651 | Enable support for local timers on SMP platforms, rather then the |
| 1652 | legacy IPI broadcast method. Local timers allows the system |
| 1653 | accounting to be spread across the timer interval, preventing a |
| 1654 | "thundering herd" at every timer tick. |
| 1655 | |
| 1656 | # The GPIO number here must be sorted by descending number. In case of |
| 1657 | # a multiplatform kernel, we just want the highest value required by the |
| 1658 | # selected platforms. |
| 1659 | config ARCH_NR_GPIO |
| 1660 | int |
| 1661 | default 1024 if ARCH_SHMOBILE || ARCH_TEGRA |
| 1662 | default 512 if SOC_OMAP5 |
| 1663 | default 355 if ARCH_U8500 |
| 1664 | default 288 if ARCH_VT8500 || ARCH_SUNXI |
| 1665 | default 264 if MACH_H4700 |
| 1666 | default 0 |
| 1667 | help |
| 1668 | Maximum number of GPIOs in the system. |
| 1669 | |
| 1670 | If unsure, leave the default value. |
| 1671 | |
| 1672 | source kernel/Kconfig.preempt |
| 1673 | |
| 1674 | config HZ |
| 1675 | int |
| 1676 | default 200 if ARCH_EBSA110 || ARCH_S3C24XX || ARCH_S5P64X0 || \ |
| 1677 | ARCH_S5PV210 || ARCH_EXYNOS4 |
| 1678 | default AT91_TIMER_HZ if ARCH_AT91 |
| 1679 | default SHMOBILE_TIMER_HZ if ARCH_SHMOBILE |
| 1680 | default 100 |
| 1681 | |
| 1682 | config SCHED_HRTICK |
| 1683 | def_bool HIGH_RES_TIMERS |
| 1684 | |
| 1685 | config THUMB2_KERNEL |
| 1686 | bool "Compile the kernel in Thumb-2 mode" |
| 1687 | depends on CPU_V7 && !CPU_V6 && !CPU_V6K |
| 1688 | select AEABI |
| 1689 | select ARM_ASM_UNIFIED |
| 1690 | select ARM_UNWIND |
| 1691 | help |
| 1692 | By enabling this option, the kernel will be compiled in |
| 1693 | Thumb-2 mode. A compiler/assembler that understand the unified |
| 1694 | ARM-Thumb syntax is needed. |
| 1695 | |
| 1696 | If unsure, say N. |
| 1697 | |
| 1698 | config THUMB2_AVOID_R_ARM_THM_JUMP11 |
| 1699 | bool "Work around buggy Thumb-2 short branch relocations in gas" |
| 1700 | depends on THUMB2_KERNEL && MODULES |
| 1701 | default y |
| 1702 | help |
| 1703 | Various binutils versions can resolve Thumb-2 branches to |
| 1704 | locally-defined, preemptible global symbols as short-range "b.n" |
| 1705 | branch instructions. |
| 1706 | |
| 1707 | This is a problem, because there's no guarantee the final |
| 1708 | destination of the symbol, or any candidate locations for a |
| 1709 | trampoline, are within range of the branch. For this reason, the |
| 1710 | kernel does not support fixing up the R_ARM_THM_JUMP11 (102) |
| 1711 | relocation in modules at all, and it makes little sense to add |
| 1712 | support. |
| 1713 | |
| 1714 | The symptom is that the kernel fails with an "unsupported |
| 1715 | relocation" error when loading some modules. |
| 1716 | |
| 1717 | Until fixed tools are available, passing |
| 1718 | -fno-optimize-sibling-calls to gcc should prevent gcc generating |
| 1719 | code which hits this problem, at the cost of a bit of extra runtime |
| 1720 | stack usage in some cases. |
| 1721 | |
| 1722 | The problem is described in more detail at: |
| 1723 | https://bugs.launchpad.net/binutils-linaro/+bug/725126 |
| 1724 | |
| 1725 | Only Thumb-2 kernels are affected. |
| 1726 | |
| 1727 | Unless you are sure your tools don't have this problem, say Y. |
| 1728 | |
| 1729 | config ARM_ASM_UNIFIED |
| 1730 | bool |
| 1731 | |
| 1732 | config AEABI |
| 1733 | bool "Use the ARM EABI to compile the kernel" |
| 1734 | help |
| 1735 | This option allows for the kernel to be compiled using the latest |
| 1736 | ARM ABI (aka EABI). This is only useful if you are using a user |
| 1737 | space environment that is also compiled with EABI. |
| 1738 | |
| 1739 | Since there are major incompatibilities between the legacy ABI and |
| 1740 | EABI, especially with regard to structure member alignment, this |
| 1741 | option also changes the kernel syscall calling convention to |
| 1742 | disambiguate both ABIs and allow for backward compatibility support |
| 1743 | (selected with CONFIG_OABI_COMPAT). |
| 1744 | |
| 1745 | To use this you need GCC version 4.0.0 or later. |
| 1746 | |
| 1747 | config OABI_COMPAT |
| 1748 | bool "Allow old ABI binaries to run with this kernel (EXPERIMENTAL)" |
| 1749 | depends on AEABI && !THUMB2_KERNEL |
| 1750 | default y |
| 1751 | help |
| 1752 | This option preserves the old syscall interface along with the |
| 1753 | new (ARM EABI) one. It also provides a compatibility layer to |
| 1754 | intercept syscalls that have structure arguments which layout |
| 1755 | in memory differs between the legacy ABI and the new ARM EABI |
| 1756 | (only for non "thumb" binaries). This option adds a tiny |
| 1757 | overhead to all syscalls and produces a slightly larger kernel. |
| 1758 | If you know you'll be using only pure EABI user space then you |
| 1759 | can say N here. If this option is not selected and you attempt |
| 1760 | to execute a legacy ABI binary then the result will be |
| 1761 | UNPREDICTABLE (in fact it can be predicted that it won't work |
| 1762 | at all). If in doubt say Y. |
| 1763 | |
| 1764 | config ARCH_HAS_HOLES_MEMORYMODEL |
| 1765 | bool |
| 1766 | |
| 1767 | config ARCH_SPARSEMEM_ENABLE |
| 1768 | bool |
| 1769 | |
| 1770 | config ARCH_SPARSEMEM_DEFAULT |
| 1771 | def_bool ARCH_SPARSEMEM_ENABLE |
| 1772 | |
| 1773 | config ARCH_SELECT_MEMORY_MODEL |
| 1774 | def_bool ARCH_SPARSEMEM_ENABLE |
| 1775 | |
| 1776 | config HAVE_ARCH_PFN_VALID |
| 1777 | def_bool ARCH_HAS_HOLES_MEMORYMODEL || !SPARSEMEM |
| 1778 | |
| 1779 | config HIGHMEM |
| 1780 | bool "High Memory Support" |
| 1781 | depends on MMU |
| 1782 | help |
| 1783 | The address space of ARM processors is only 4 Gigabytes large |
| 1784 | and it has to accommodate user address space, kernel address |
| 1785 | space as well as some memory mapped IO. That means that, if you |
| 1786 | have a large amount of physical memory and/or IO, not all of the |
| 1787 | memory can be "permanently mapped" by the kernel. The physical |
| 1788 | memory that is not permanently mapped is called "high memory". |
| 1789 | |
| 1790 | Depending on the selected kernel/user memory split, minimum |
| 1791 | vmalloc space and actual amount of RAM, you may not need this |
| 1792 | option which should result in a slightly faster kernel. |
| 1793 | |
| 1794 | If unsure, say n. |
| 1795 | |
| 1796 | config HIGHPTE |
| 1797 | bool "Allocate 2nd-level pagetables from highmem" |
| 1798 | depends on HIGHMEM |
| 1799 | |
| 1800 | config HW_PERF_EVENTS |
| 1801 | bool "Enable hardware performance counter support for perf events" |
| 1802 | depends on PERF_EVENTS |
| 1803 | default y |
| 1804 | help |
| 1805 | Enable hardware performance counter support for perf events. If |
| 1806 | disabled, perf events will use software events only. |
| 1807 | |
| 1808 | source "mm/Kconfig" |
| 1809 | |
| 1810 | config FORCE_MAX_ZONEORDER |
| 1811 | int "Maximum zone order" if ARCH_SHMOBILE |
| 1812 | range 11 64 if ARCH_SHMOBILE |
| 1813 | default "12" if SOC_AM33XX |
| 1814 | default "9" if SA1111 |
| 1815 | default "11" |
| 1816 | help |
| 1817 | The kernel memory allocator divides physically contiguous memory |
| 1818 | blocks into "zones", where each zone is a power of two number of |
| 1819 | pages. This option selects the largest power of two that the kernel |
| 1820 | keeps in the memory allocator. If you need to allocate very large |
| 1821 | blocks of physically contiguous memory, then you may need to |
| 1822 | increase this value. |
| 1823 | |
| 1824 | This config option is actually maximum order plus one. For example, |
| 1825 | a value of 11 means that the largest free memory block is 2^10 pages. |
| 1826 | |
| 1827 | config ALIGNMENT_TRAP |
| 1828 | bool |
| 1829 | depends on CPU_CP15_MMU |
| 1830 | default y if !ARCH_EBSA110 |
| 1831 | select HAVE_PROC_CPU if PROC_FS |
| 1832 | help |
| 1833 | ARM processors cannot fetch/store information which is not |
| 1834 | naturally aligned on the bus, i.e., a 4 byte fetch must start at an |
| 1835 | address divisible by 4. On 32-bit ARM processors, these non-aligned |
| 1836 | fetch/store instructions will be emulated in software if you say |
| 1837 | here, which has a severe performance impact. This is necessary for |
| 1838 | correct operation of some network protocols. With an IP-only |
| 1839 | configuration it is safe to say N, otherwise say Y. |
| 1840 | |
| 1841 | config UACCESS_WITH_MEMCPY |
| 1842 | bool "Use kernel mem{cpy,set}() for {copy_to,clear}_user()" |
| 1843 | depends on MMU |
| 1844 | default y if CPU_FEROCEON |
| 1845 | help |
| 1846 | Implement faster copy_to_user and clear_user methods for CPU |
| 1847 | cores where a 8-word STM instruction give significantly higher |
| 1848 | memory write throughput than a sequence of individual 32bit stores. |
| 1849 | |
| 1850 | A possible side effect is a slight increase in scheduling latency |
| 1851 | between threads sharing the same address space if they invoke |
| 1852 | such copy operations with large buffers. |
| 1853 | |
| 1854 | However, if the CPU data cache is using a write-allocate mode, |
| 1855 | this option is unlikely to provide any performance gain. |
| 1856 | |
| 1857 | config SECCOMP |
| 1858 | bool |
| 1859 | prompt "Enable seccomp to safely compute untrusted bytecode" |
| 1860 | ---help--- |
| 1861 | This kernel feature is useful for number crunching applications |
| 1862 | that may need to compute untrusted bytecode during their |
| 1863 | execution. By using pipes or other transports made available to |
| 1864 | the process as file descriptors supporting the read/write |
| 1865 | syscalls, it's possible to isolate those applications in |
| 1866 | their own address space using seccomp. Once seccomp is |
| 1867 | enabled via prctl(PR_SET_SECCOMP), it cannot be disabled |
| 1868 | and the task is only allowed to execute a few safe syscalls |
| 1869 | defined by each seccomp mode. |
| 1870 | |
| 1871 | config CC_STACKPROTECTOR |
| 1872 | bool "Enable -fstack-protector buffer overflow detection (EXPERIMENTAL)" |
| 1873 | help |
| 1874 | This option turns on the -fstack-protector GCC feature. This |
| 1875 | feature puts, at the beginning of functions, a canary value on |
| 1876 | the stack just before the return address, and validates |
| 1877 | the value just before actually returning. Stack based buffer |
| 1878 | overflows (that need to overwrite this return address) now also |
| 1879 | overwrite the canary, which gets detected and the attack is then |
| 1880 | neutralized via a kernel panic. |
| 1881 | This feature requires gcc version 4.2 or above. |
| 1882 | |
| 1883 | config XEN_DOM0 |
| 1884 | def_bool y |
| 1885 | depends on XEN |
| 1886 | |
| 1887 | config XEN |
| 1888 | bool "Xen guest support on ARM (EXPERIMENTAL)" |
| 1889 | depends on ARM && AEABI && OF |
| 1890 | depends on CPU_V7 && !CPU_V6 |
| 1891 | depends on !GENERIC_ATOMIC64 |
| 1892 | help |
| 1893 | Say Y if you want to run Linux in a Virtual Machine on Xen on ARM. |
| 1894 | |
| 1895 | endmenu |
| 1896 | |
| 1897 | menu "Boot options" |
| 1898 | |
| 1899 | config USE_OF |
| 1900 | bool "Flattened Device Tree support" |
| 1901 | select IRQ_DOMAIN |
| 1902 | select OF |
| 1903 | select OF_EARLY_FLATTREE |
| 1904 | help |
| 1905 | Include support for flattened device tree machine descriptions. |
| 1906 | |
| 1907 | config ATAGS |
| 1908 | bool "Support for the traditional ATAGS boot data passing" if USE_OF |
| 1909 | default y |
| 1910 | help |
| 1911 | This is the traditional way of passing data to the kernel at boot |
| 1912 | time. If you are solely relying on the flattened device tree (or |
| 1913 | the ARM_ATAG_DTB_COMPAT option) then you may unselect this option |
| 1914 | to remove ATAGS support from your kernel binary. If unsure, |
| 1915 | leave this to y. |
| 1916 | |
| 1917 | config DEPRECATED_PARAM_STRUCT |
| 1918 | bool "Provide old way to pass kernel parameters" |
| 1919 | depends on ATAGS |
| 1920 | help |
| 1921 | This was deprecated in 2001 and announced to live on for 5 years. |
| 1922 | Some old boot loaders still use this way. |
| 1923 | |
| 1924 | # Compressed boot loader in ROM. Yes, we really want to ask about |
| 1925 | # TEXT and BSS so we preserve their values in the config files. |
| 1926 | config ZBOOT_ROM_TEXT |
| 1927 | hex "Compressed ROM boot loader base address" |
| 1928 | default "0" |
| 1929 | help |
| 1930 | The physical address at which the ROM-able zImage is to be |
| 1931 | placed in the target. Platforms which normally make use of |
| 1932 | ROM-able zImage formats normally set this to a suitable |
| 1933 | value in their defconfig file. |
| 1934 | |
| 1935 | If ZBOOT_ROM is not enabled, this has no effect. |
| 1936 | |
| 1937 | config ZBOOT_ROM_BSS |
| 1938 | hex "Compressed ROM boot loader BSS address" |
| 1939 | default "0" |
| 1940 | help |
| 1941 | The base address of an area of read/write memory in the target |
| 1942 | for the ROM-able zImage which must be available while the |
| 1943 | decompressor is running. It must be large enough to hold the |
| 1944 | entire decompressed kernel plus an additional 128 KiB. |
| 1945 | Platforms which normally make use of ROM-able zImage formats |
| 1946 | normally set this to a suitable value in their defconfig file. |
| 1947 | |
| 1948 | If ZBOOT_ROM is not enabled, this has no effect. |
| 1949 | |
| 1950 | config ZBOOT_ROM |
| 1951 | bool "Compressed boot loader in ROM/flash" |
| 1952 | depends on ZBOOT_ROM_TEXT != ZBOOT_ROM_BSS |
| 1953 | help |
| 1954 | Say Y here if you intend to execute your compressed kernel image |
| 1955 | (zImage) directly from ROM or flash. If unsure, say N. |
| 1956 | |
| 1957 | choice |
| 1958 | prompt "Include SD/MMC loader in zImage (EXPERIMENTAL)" |
| 1959 | depends on ZBOOT_ROM && ARCH_SH7372 |
| 1960 | default ZBOOT_ROM_NONE |
| 1961 | help |
| 1962 | Include experimental SD/MMC loading code in the ROM-able zImage. |
| 1963 | With this enabled it is possible to write the ROM-able zImage |
| 1964 | kernel image to an MMC or SD card and boot the kernel straight |
| 1965 | from the reset vector. At reset the processor Mask ROM will load |
| 1966 | the first part of the ROM-able zImage which in turn loads the |
| 1967 | rest the kernel image to RAM. |
| 1968 | |
| 1969 | config ZBOOT_ROM_NONE |
| 1970 | bool "No SD/MMC loader in zImage (EXPERIMENTAL)" |
| 1971 | help |
| 1972 | Do not load image from SD or MMC |
| 1973 | |
| 1974 | config ZBOOT_ROM_MMCIF |
| 1975 | bool "Include MMCIF loader in zImage (EXPERIMENTAL)" |
| 1976 | help |
| 1977 | Load image from MMCIF hardware block. |
| 1978 | |
| 1979 | config ZBOOT_ROM_SH_MOBILE_SDHI |
| 1980 | bool "Include SuperH Mobile SDHI loader in zImage (EXPERIMENTAL)" |
| 1981 | help |
| 1982 | Load image from SDHI hardware block |
| 1983 | |
| 1984 | endchoice |
| 1985 | |
| 1986 | config ARM_APPENDED_DTB |
| 1987 | bool "Use appended device tree blob to zImage (EXPERIMENTAL)" |
| 1988 | depends on OF && !ZBOOT_ROM |
| 1989 | help |
| 1990 | With this option, the boot code will look for a device tree binary |
| 1991 | (DTB) appended to zImage |
| 1992 | (e.g. cat zImage <filename>.dtb > zImage_w_dtb). |
| 1993 | |
| 1994 | This is meant as a backward compatibility convenience for those |
| 1995 | systems with a bootloader that can't be upgraded to accommodate |
| 1996 | the documented boot protocol using a device tree. |
| 1997 | |
| 1998 | Beware that there is very little in terms of protection against |
| 1999 | this option being confused by leftover garbage in memory that might |
| 2000 | look like a DTB header after a reboot if no actual DTB is appended |
| 2001 | to zImage. Do not leave this option active in a production kernel |
| 2002 | if you don't intend to always append a DTB. Proper passing of the |
| 2003 | location into r2 of a bootloader provided DTB is always preferable |
| 2004 | to this option. |
| 2005 | |
| 2006 | config ARM_ATAG_DTB_COMPAT |
| 2007 | bool "Supplement the appended DTB with traditional ATAG information" |
| 2008 | depends on ARM_APPENDED_DTB |
| 2009 | help |
| 2010 | Some old bootloaders can't be updated to a DTB capable one, yet |
| 2011 | they provide ATAGs with memory configuration, the ramdisk address, |
| 2012 | the kernel cmdline string, etc. Such information is dynamically |
| 2013 | provided by the bootloader and can't always be stored in a static |
| 2014 | DTB. To allow a device tree enabled kernel to be used with such |
| 2015 | bootloaders, this option allows zImage to extract the information |
| 2016 | from the ATAG list and store it at run time into the appended DTB. |
| 2017 | |
| 2018 | choice |
| 2019 | prompt "Kernel command line type" if ARM_ATAG_DTB_COMPAT |
| 2020 | default ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER |
| 2021 | |
| 2022 | config ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER |
| 2023 | bool "Use bootloader kernel arguments if available" |
| 2024 | help |
| 2025 | Uses the command-line options passed by the boot loader instead of |
| 2026 | the device tree bootargs property. If the boot loader doesn't provide |
| 2027 | any, the device tree bootargs property will be used. |
| 2028 | |
| 2029 | config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND |
| 2030 | bool "Extend with bootloader kernel arguments" |
| 2031 | help |
| 2032 | The command-line arguments provided by the boot loader will be |
| 2033 | appended to the the device tree bootargs property. |
| 2034 | |
| 2035 | endchoice |
| 2036 | |
| 2037 | config CMDLINE |
| 2038 | string "Default kernel command string" |
| 2039 | default "" |
| 2040 | help |
| 2041 | On some architectures (EBSA110 and CATS), there is currently no way |
| 2042 | for the boot loader to pass arguments to the kernel. For these |
| 2043 | architectures, you should supply some command-line options at build |
| 2044 | time by entering them here. As a minimum, you should specify the |
| 2045 | memory size and the root device (e.g., mem=64M root=/dev/nfs). |
| 2046 | |
| 2047 | choice |
| 2048 | prompt "Kernel command line type" if CMDLINE != "" |
| 2049 | default CMDLINE_FROM_BOOTLOADER |
| 2050 | depends on ATAGS |
| 2051 | |
| 2052 | config CMDLINE_FROM_BOOTLOADER |
| 2053 | bool "Use bootloader kernel arguments if available" |
| 2054 | help |
| 2055 | Uses the command-line options passed by the boot loader. If |
| 2056 | the boot loader doesn't provide any, the default kernel command |
| 2057 | string provided in CMDLINE will be used. |
| 2058 | |
| 2059 | config CMDLINE_EXTEND |
| 2060 | bool "Extend bootloader kernel arguments" |
| 2061 | help |
| 2062 | The command-line arguments provided by the boot loader will be |
| 2063 | appended to the default kernel command string. |
| 2064 | |
| 2065 | config CMDLINE_FORCE |
| 2066 | bool "Always use the default kernel command string" |
| 2067 | help |
| 2068 | Always use the default kernel command string, even if the boot |
| 2069 | loader passes other arguments to the kernel. |
| 2070 | This is useful if you cannot or don't want to change the |
| 2071 | command-line options your boot loader passes to the kernel. |
| 2072 | endchoice |
| 2073 | |
| 2074 | config XIP_KERNEL |
| 2075 | bool "Kernel Execute-In-Place from ROM" |
| 2076 | depends on !ZBOOT_ROM && !ARM_LPAE && !ARCH_MULTIPLATFORM |
| 2077 | help |
| 2078 | Execute-In-Place allows the kernel to run from non-volatile storage |
| 2079 | directly addressable by the CPU, such as NOR flash. This saves RAM |
| 2080 | space since the text section of the kernel is not loaded from flash |
| 2081 | to RAM. Read-write sections, such as the data section and stack, |
| 2082 | are still copied to RAM. The XIP kernel is not compressed since |
| 2083 | it has to run directly from flash, so it will take more space to |
| 2084 | store it. The flash address used to link the kernel object files, |
| 2085 | and for storing it, is configuration dependent. Therefore, if you |
| 2086 | say Y here, you must know the proper physical address where to |
| 2087 | store the kernel image depending on your own flash memory usage. |
| 2088 | |
| 2089 | Also note that the make target becomes "make xipImage" rather than |
| 2090 | "make zImage" or "make Image". The final kernel binary to put in |
| 2091 | ROM memory will be arch/arm/boot/xipImage. |
| 2092 | |
| 2093 | If unsure, say N. |
| 2094 | |
| 2095 | config XIP_PHYS_ADDR |
| 2096 | hex "XIP Kernel Physical Location" |
| 2097 | depends on XIP_KERNEL |
| 2098 | default "0x00080000" |
| 2099 | help |
| 2100 | This is the physical address in your flash memory the kernel will |
| 2101 | be linked for and stored to. This address is dependent on your |
| 2102 | own flash usage. |
| 2103 | |
| 2104 | config KEXEC |
| 2105 | bool "Kexec system call (EXPERIMENTAL)" |
| 2106 | depends on (!SMP || HOTPLUG_CPU) |
| 2107 | help |
| 2108 | kexec is a system call that implements the ability to shutdown your |
| 2109 | current kernel, and to start another kernel. It is like a reboot |
| 2110 | but it is independent of the system firmware. And like a reboot |
| 2111 | you can start any kernel with it, not just Linux. |
| 2112 | |
| 2113 | It is an ongoing process to be certain the hardware in a machine |
| 2114 | is properly shutdown, so do not be surprised if this code does not |
| 2115 | initially work for you. It may help to enable device hotplugging |
| 2116 | support. |
| 2117 | |
| 2118 | config ATAGS_PROC |
| 2119 | bool "Export atags in procfs" |
| 2120 | depends on ATAGS && KEXEC |
| 2121 | default y |
| 2122 | help |
| 2123 | Should the atags used to boot the kernel be exported in an "atags" |
| 2124 | file in procfs. Useful with kexec. |
| 2125 | |
| 2126 | config CRASH_DUMP |
| 2127 | bool "Build kdump crash kernel (EXPERIMENTAL)" |
| 2128 | help |
| 2129 | Generate crash dump after being started by kexec. This should |
| 2130 | be normally only set in special crash dump kernels which are |
| 2131 | loaded in the main kernel with kexec-tools into a specially |
| 2132 | reserved region and then later executed after a crash by |
| 2133 | kdump/kexec. The crash dump kernel must be compiled to a |
| 2134 | memory address not used by the main kernel |
| 2135 | |
| 2136 | For more details see Documentation/kdump/kdump.txt |
| 2137 | |
| 2138 | config AUTO_ZRELADDR |
| 2139 | bool "Auto calculation of the decompressed kernel image address" |
| 2140 | depends on !ZBOOT_ROM && !ARCH_U300 |
| 2141 | help |
| 2142 | ZRELADDR is the physical address where the decompressed kernel |
| 2143 | image will be placed. If AUTO_ZRELADDR is selected, the address |
| 2144 | will be determined at run-time by masking the current IP with |
| 2145 | 0xf8000000. This assumes the zImage being placed in the first 128MB |
| 2146 | from start of memory. |
| 2147 | |
| 2148 | endmenu |
| 2149 | |
| 2150 | menu "CPU Power Management" |
| 2151 | |
| 2152 | if ARCH_HAS_CPUFREQ |
| 2153 | |
| 2154 | source "drivers/cpufreq/Kconfig" |
| 2155 | |
| 2156 | config CPU_FREQ_IMX |
| 2157 | tristate "CPUfreq driver for i.MX CPUs" |
| 2158 | depends on ARCH_MXC && CPU_FREQ |
| 2159 | select CPU_FREQ_TABLE |
| 2160 | help |
| 2161 | This enables the CPUfreq driver for i.MX CPUs. |
| 2162 | |
| 2163 | config CPU_FREQ_SA1100 |
| 2164 | bool |
| 2165 | |
| 2166 | config CPU_FREQ_SA1110 |
| 2167 | bool |
| 2168 | |
| 2169 | config CPU_FREQ_INTEGRATOR |
| 2170 | tristate "CPUfreq driver for ARM Integrator CPUs" |
| 2171 | depends on ARCH_INTEGRATOR && CPU_FREQ |
| 2172 | default y |
| 2173 | help |
| 2174 | This enables the CPUfreq driver for ARM Integrator CPUs. |
| 2175 | |
| 2176 | For details, take a look at <file:Documentation/cpu-freq>. |
| 2177 | |
| 2178 | If in doubt, say Y. |
| 2179 | |
| 2180 | config CPU_FREQ_PXA |
| 2181 | bool |
| 2182 | depends on CPU_FREQ && ARCH_PXA && PXA25x |
| 2183 | default y |
| 2184 | select CPU_FREQ_DEFAULT_GOV_USERSPACE |
| 2185 | select CPU_FREQ_TABLE |
| 2186 | |
| 2187 | config CPU_FREQ_S3C |
| 2188 | bool |
| 2189 | help |
| 2190 | Internal configuration node for common cpufreq on Samsung SoC |
| 2191 | |
| 2192 | config CPU_FREQ_S3C24XX |
| 2193 | bool "CPUfreq driver for Samsung S3C24XX series CPUs (EXPERIMENTAL)" |
| 2194 | depends on ARCH_S3C24XX && CPU_FREQ |
| 2195 | select CPU_FREQ_S3C |
| 2196 | help |
| 2197 | This enables the CPUfreq driver for the Samsung S3C24XX family |
| 2198 | of CPUs. |
| 2199 | |
| 2200 | For details, take a look at <file:Documentation/cpu-freq>. |
| 2201 | |
| 2202 | If in doubt, say N. |
| 2203 | |
| 2204 | config CPU_FREQ_S3C24XX_PLL |
| 2205 | bool "Support CPUfreq changing of PLL frequency (EXPERIMENTAL)" |
| 2206 | depends on CPU_FREQ_S3C24XX |
| 2207 | help |
| 2208 | Compile in support for changing the PLL frequency from the |
| 2209 | S3C24XX series CPUfreq driver. The PLL takes time to settle |
| 2210 | after a frequency change, so by default it is not enabled. |
| 2211 | |
| 2212 | This also means that the PLL tables for the selected CPU(s) will |
| 2213 | be built which may increase the size of the kernel image. |
| 2214 | |
| 2215 | config CPU_FREQ_S3C24XX_DEBUG |
| 2216 | bool "Debug CPUfreq Samsung driver core" |
| 2217 | depends on CPU_FREQ_S3C24XX |
| 2218 | help |
| 2219 | Enable s3c_freq_dbg for the Samsung S3C CPUfreq core |
| 2220 | |
| 2221 | config CPU_FREQ_S3C24XX_IODEBUG |
| 2222 | bool "Debug CPUfreq Samsung driver IO timing" |
| 2223 | depends on CPU_FREQ_S3C24XX |
| 2224 | help |
| 2225 | Enable s3c_freq_iodbg for the Samsung S3C CPUfreq core |
| 2226 | |
| 2227 | config CPU_FREQ_S3C24XX_DEBUGFS |
| 2228 | bool "Export debugfs for CPUFreq" |
| 2229 | depends on CPU_FREQ_S3C24XX && DEBUG_FS |
| 2230 | help |
| 2231 | Export status information via debugfs. |
| 2232 | |
| 2233 | endif |
| 2234 | |
| 2235 | source "drivers/cpuidle/Kconfig" |
| 2236 | |
| 2237 | endmenu |
| 2238 | |
| 2239 | menu "Floating point emulation" |
| 2240 | |
| 2241 | comment "At least one emulation must be selected" |
| 2242 | |
| 2243 | config FPE_NWFPE |
| 2244 | bool "NWFPE math emulation" |
| 2245 | depends on (!AEABI || OABI_COMPAT) && !THUMB2_KERNEL |
| 2246 | ---help--- |
| 2247 | Say Y to include the NWFPE floating point emulator in the kernel. |
| 2248 | This is necessary to run most binaries. Linux does not currently |
| 2249 | support floating point hardware so you need to say Y here even if |
| 2250 | your machine has an FPA or floating point co-processor podule. |
| 2251 | |
| 2252 | You may say N here if you are going to load the Acorn FPEmulator |
| 2253 | early in the bootup. |
| 2254 | |
| 2255 | config FPE_NWFPE_XP |
| 2256 | bool "Support extended precision" |
| 2257 | depends on FPE_NWFPE |
| 2258 | help |
| 2259 | Say Y to include 80-bit support in the kernel floating-point |
| 2260 | emulator. Otherwise, only 32 and 64-bit support is compiled in. |
| 2261 | Note that gcc does not generate 80-bit operations by default, |
| 2262 | so in most cases this option only enlarges the size of the |
| 2263 | floating point emulator without any good reason. |
| 2264 | |
| 2265 | You almost surely want to say N here. |
| 2266 | |
| 2267 | config FPE_FASTFPE |
| 2268 | bool "FastFPE math emulation (EXPERIMENTAL)" |
| 2269 | depends on (!AEABI || OABI_COMPAT) && !CPU_32v3 |
| 2270 | ---help--- |
| 2271 | Say Y here to include the FAST floating point emulator in the kernel. |
| 2272 | This is an experimental much faster emulator which now also has full |
| 2273 | precision for the mantissa. It does not support any exceptions. |
| 2274 | It is very simple, and approximately 3-6 times faster than NWFPE. |
| 2275 | |
| 2276 | It should be sufficient for most programs. It may be not suitable |
| 2277 | for scientific calculations, but you have to check this for yourself. |
| 2278 | If you do not feel you need a faster FP emulation you should better |
| 2279 | choose NWFPE. |
| 2280 | |
| 2281 | config VFP |
| 2282 | bool "VFP-format floating point maths" |
| 2283 | depends on CPU_V6 || CPU_V6K || CPU_ARM926T || CPU_V7 || CPU_FEROCEON |
| 2284 | help |
| 2285 | Say Y to include VFP support code in the kernel. This is needed |
| 2286 | if your hardware includes a VFP unit. |
| 2287 | |
| 2288 | Please see <file:Documentation/arm/VFP/release-notes.txt> for |
| 2289 | release notes and additional status information. |
| 2290 | |
| 2291 | Say N if your target does not have VFP hardware. |
| 2292 | |
| 2293 | config VFPv3 |
| 2294 | bool |
| 2295 | depends on VFP |
| 2296 | default y if CPU_V7 |
| 2297 | |
| 2298 | config NEON |
| 2299 | bool "Advanced SIMD (NEON) Extension support" |
| 2300 | depends on VFPv3 && CPU_V7 |
| 2301 | help |
| 2302 | Say Y to include support code for NEON, the ARMv7 Advanced SIMD |
| 2303 | Extension. |
| 2304 | |
| 2305 | endmenu |
| 2306 | |
| 2307 | menu "Userspace binary formats" |
| 2308 | |
| 2309 | source "fs/Kconfig.binfmt" |
| 2310 | |
| 2311 | config ARTHUR |
| 2312 | tristate "RISC OS personality" |
| 2313 | depends on !AEABI |
| 2314 | help |
| 2315 | Say Y here to include the kernel code necessary if you want to run |
| 2316 | Acorn RISC OS/Arthur binaries under Linux. This code is still very |
| 2317 | experimental; if this sounds frightening, say N and sleep in peace. |
| 2318 | You can also say M here to compile this support as a module (which |
| 2319 | will be called arthur). |
| 2320 | |
| 2321 | endmenu |
| 2322 | |
| 2323 | menu "Power management options" |
| 2324 | |
| 2325 | source "kernel/power/Kconfig" |
| 2326 | |
| 2327 | config ARCH_SUSPEND_POSSIBLE |
| 2328 | depends on !ARCH_S5PC100 |
| 2329 | depends on CPU_ARM920T || CPU_ARM926T || CPU_SA1100 || \ |
| 2330 | CPU_V6 || CPU_V6K || CPU_V7 || CPU_XSC3 || CPU_XSCALE || CPU_MOHAWK |
| 2331 | def_bool y |
| 2332 | |
| 2333 | config ARM_CPU_SUSPEND |
| 2334 | def_bool PM_SLEEP |
| 2335 | |
| 2336 | endmenu |
| 2337 | |
| 2338 | source "net/Kconfig" |
| 2339 | |
| 2340 | source "drivers/Kconfig" |
| 2341 | |
| 2342 | source "fs/Kconfig" |
| 2343 | |
| 2344 | source "arch/arm/Kconfig.debug" |
| 2345 | |
| 2346 | source "security/Kconfig" |
| 2347 | |
| 2348 | source "crypto/Kconfig" |
| 2349 | |
| 2350 | source "lib/Kconfig" |
| 2351 | |
| 2352 | source "arch/arm/kvm/Kconfig" |