| 1 | /* |
| 2 | * Local APIC handling, local APIC timers |
| 3 | * |
| 4 | * (c) 1999, 2000 Ingo Molnar <mingo@redhat.com> |
| 5 | * |
| 6 | * Fixes |
| 7 | * Maciej W. Rozycki : Bits for genuine 82489DX APICs; |
| 8 | * thanks to Eric Gilmore |
| 9 | * and Rolf G. Tews |
| 10 | * for testing these extensively. |
| 11 | * Maciej W. Rozycki : Various updates and fixes. |
| 12 | * Mikael Pettersson : Power Management for UP-APIC. |
| 13 | * Pavel Machek and |
| 14 | * Mikael Pettersson : PM converted to driver model. |
| 15 | */ |
| 16 | |
| 17 | #include <linux/init.h> |
| 18 | |
| 19 | #include <linux/mm.h> |
| 20 | #include <linux/delay.h> |
| 21 | #include <linux/bootmem.h> |
| 22 | #include <linux/interrupt.h> |
| 23 | #include <linux/mc146818rtc.h> |
| 24 | #include <linux/kernel_stat.h> |
| 25 | #include <linux/sysdev.h> |
| 26 | #include <linux/ioport.h> |
| 27 | #include <linux/cpu.h> |
| 28 | #include <linux/clockchips.h> |
| 29 | #include <linux/acpi_pmtmr.h> |
| 30 | #include <linux/module.h> |
| 31 | #include <linux/dmi.h> |
| 32 | #include <linux/dmar.h> |
| 33 | |
| 34 | #include <asm/atomic.h> |
| 35 | #include <asm/smp.h> |
| 36 | #include <asm/mtrr.h> |
| 37 | #include <asm/mpspec.h> |
| 38 | #include <asm/desc.h> |
| 39 | #include <asm/arch_hooks.h> |
| 40 | #include <asm/hpet.h> |
| 41 | #include <asm/pgalloc.h> |
| 42 | #include <asm/i8253.h> |
| 43 | #include <asm/nmi.h> |
| 44 | #include <asm/idle.h> |
| 45 | #include <asm/proto.h> |
| 46 | #include <asm/timex.h> |
| 47 | #include <asm/apic.h> |
| 48 | #include <asm/i8259.h> |
| 49 | |
| 50 | #include <mach_apic.h> |
| 51 | #include <mach_apicdef.h> |
| 52 | #include <mach_ipi.h> |
| 53 | |
| 54 | /* |
| 55 | * Sanity check |
| 56 | */ |
| 57 | #if ((SPURIOUS_APIC_VECTOR & 0x0F) != 0x0F) |
| 58 | # error SPURIOUS_APIC_VECTOR definition error |
| 59 | #endif |
| 60 | |
| 61 | #ifdef CONFIG_X86_32 |
| 62 | /* |
| 63 | * Knob to control our willingness to enable the local APIC. |
| 64 | * |
| 65 | * +1=force-enable |
| 66 | */ |
| 67 | static int force_enable_local_apic; |
| 68 | /* |
| 69 | * APIC command line parameters |
| 70 | */ |
| 71 | static int __init parse_lapic(char *arg) |
| 72 | { |
| 73 | force_enable_local_apic = 1; |
| 74 | return 0; |
| 75 | } |
| 76 | early_param("lapic", parse_lapic); |
| 77 | /* Local APIC was disabled by the BIOS and enabled by the kernel */ |
| 78 | static int enabled_via_apicbase; |
| 79 | |
| 80 | #endif |
| 81 | |
| 82 | #ifdef CONFIG_X86_64 |
| 83 | static int apic_calibrate_pmtmr __initdata; |
| 84 | static __init int setup_apicpmtimer(char *s) |
| 85 | { |
| 86 | apic_calibrate_pmtmr = 1; |
| 87 | notsc_setup(NULL); |
| 88 | return 0; |
| 89 | } |
| 90 | __setup("apicpmtimer", setup_apicpmtimer); |
| 91 | #endif |
| 92 | |
| 93 | #ifdef CONFIG_X86_64 |
| 94 | #define HAVE_X2APIC |
| 95 | #endif |
| 96 | |
| 97 | #ifdef HAVE_X2APIC |
| 98 | int x2apic; |
| 99 | /* x2apic enabled before OS handover */ |
| 100 | int x2apic_preenabled; |
| 101 | int disable_x2apic; |
| 102 | static __init int setup_nox2apic(char *str) |
| 103 | { |
| 104 | disable_x2apic = 1; |
| 105 | setup_clear_cpu_cap(X86_FEATURE_X2APIC); |
| 106 | return 0; |
| 107 | } |
| 108 | early_param("nox2apic", setup_nox2apic); |
| 109 | #endif |
| 110 | |
| 111 | unsigned long mp_lapic_addr; |
| 112 | int disable_apic; |
| 113 | /* Disable local APIC timer from the kernel commandline or via dmi quirk */ |
| 114 | static int disable_apic_timer __cpuinitdata; |
| 115 | /* Local APIC timer works in C2 */ |
| 116 | int local_apic_timer_c2_ok; |
| 117 | EXPORT_SYMBOL_GPL(local_apic_timer_c2_ok); |
| 118 | |
| 119 | int first_system_vector = 0xfe; |
| 120 | |
| 121 | char system_vectors[NR_VECTORS] = { [0 ... NR_VECTORS-1] = SYS_VECTOR_FREE}; |
| 122 | |
| 123 | /* |
| 124 | * Debug level, exported for io_apic.c |
| 125 | */ |
| 126 | unsigned int apic_verbosity; |
| 127 | |
| 128 | int pic_mode; |
| 129 | |
| 130 | /* Have we found an MP table */ |
| 131 | int smp_found_config; |
| 132 | |
| 133 | static struct resource lapic_resource = { |
| 134 | .name = "Local APIC", |
| 135 | .flags = IORESOURCE_MEM | IORESOURCE_BUSY, |
| 136 | }; |
| 137 | |
| 138 | static unsigned int calibration_result; |
| 139 | |
| 140 | static int lapic_next_event(unsigned long delta, |
| 141 | struct clock_event_device *evt); |
| 142 | static void lapic_timer_setup(enum clock_event_mode mode, |
| 143 | struct clock_event_device *evt); |
| 144 | static void lapic_timer_broadcast(cpumask_t mask); |
| 145 | static void apic_pm_activate(void); |
| 146 | |
| 147 | /* |
| 148 | * The local apic timer can be used for any function which is CPU local. |
| 149 | */ |
| 150 | static struct clock_event_device lapic_clockevent = { |
| 151 | .name = "lapic", |
| 152 | .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT |
| 153 | | CLOCK_EVT_FEAT_C3STOP | CLOCK_EVT_FEAT_DUMMY, |
| 154 | .shift = 32, |
| 155 | .set_mode = lapic_timer_setup, |
| 156 | .set_next_event = lapic_next_event, |
| 157 | .broadcast = lapic_timer_broadcast, |
| 158 | .rating = 100, |
| 159 | .irq = -1, |
| 160 | }; |
| 161 | static DEFINE_PER_CPU(struct clock_event_device, lapic_events); |
| 162 | |
| 163 | static unsigned long apic_phys; |
| 164 | |
| 165 | /* |
| 166 | * Get the LAPIC version |
| 167 | */ |
| 168 | static inline int lapic_get_version(void) |
| 169 | { |
| 170 | return GET_APIC_VERSION(apic_read(APIC_LVR)); |
| 171 | } |
| 172 | |
| 173 | /* |
| 174 | * Check, if the APIC is integrated or a separate chip |
| 175 | */ |
| 176 | static inline int lapic_is_integrated(void) |
| 177 | { |
| 178 | #ifdef CONFIG_X86_64 |
| 179 | return 1; |
| 180 | #else |
| 181 | return APIC_INTEGRATED(lapic_get_version()); |
| 182 | #endif |
| 183 | } |
| 184 | |
| 185 | /* |
| 186 | * Check, whether this is a modern or a first generation APIC |
| 187 | */ |
| 188 | static int modern_apic(void) |
| 189 | { |
| 190 | /* AMD systems use old APIC versions, so check the CPU */ |
| 191 | if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD && |
| 192 | boot_cpu_data.x86 >= 0xf) |
| 193 | return 1; |
| 194 | return lapic_get_version() >= 0x14; |
| 195 | } |
| 196 | |
| 197 | /* |
| 198 | * Paravirt kernels also might be using these below ops. So we still |
| 199 | * use generic apic_read()/apic_write(), which might be pointing to different |
| 200 | * ops in PARAVIRT case. |
| 201 | */ |
| 202 | void xapic_wait_icr_idle(void) |
| 203 | { |
| 204 | while (apic_read(APIC_ICR) & APIC_ICR_BUSY) |
| 205 | cpu_relax(); |
| 206 | } |
| 207 | |
| 208 | u32 safe_xapic_wait_icr_idle(void) |
| 209 | { |
| 210 | u32 send_status; |
| 211 | int timeout; |
| 212 | |
| 213 | timeout = 0; |
| 214 | do { |
| 215 | send_status = apic_read(APIC_ICR) & APIC_ICR_BUSY; |
| 216 | if (!send_status) |
| 217 | break; |
| 218 | udelay(100); |
| 219 | } while (timeout++ < 1000); |
| 220 | |
| 221 | return send_status; |
| 222 | } |
| 223 | |
| 224 | void xapic_icr_write(u32 low, u32 id) |
| 225 | { |
| 226 | apic_write(APIC_ICR2, SET_APIC_DEST_FIELD(id)); |
| 227 | apic_write(APIC_ICR, low); |
| 228 | } |
| 229 | |
| 230 | u64 xapic_icr_read(void) |
| 231 | { |
| 232 | u32 icr1, icr2; |
| 233 | |
| 234 | icr2 = apic_read(APIC_ICR2); |
| 235 | icr1 = apic_read(APIC_ICR); |
| 236 | |
| 237 | return icr1 | ((u64)icr2 << 32); |
| 238 | } |
| 239 | |
| 240 | static struct apic_ops xapic_ops = { |
| 241 | .read = native_apic_mem_read, |
| 242 | .write = native_apic_mem_write, |
| 243 | .icr_read = xapic_icr_read, |
| 244 | .icr_write = xapic_icr_write, |
| 245 | .wait_icr_idle = xapic_wait_icr_idle, |
| 246 | .safe_wait_icr_idle = safe_xapic_wait_icr_idle, |
| 247 | }; |
| 248 | |
| 249 | struct apic_ops __read_mostly *apic_ops = &xapic_ops; |
| 250 | EXPORT_SYMBOL_GPL(apic_ops); |
| 251 | |
| 252 | #ifdef HAVE_X2APIC |
| 253 | static void x2apic_wait_icr_idle(void) |
| 254 | { |
| 255 | /* no need to wait for icr idle in x2apic */ |
| 256 | return; |
| 257 | } |
| 258 | |
| 259 | static u32 safe_x2apic_wait_icr_idle(void) |
| 260 | { |
| 261 | /* no need to wait for icr idle in x2apic */ |
| 262 | return 0; |
| 263 | } |
| 264 | |
| 265 | void x2apic_icr_write(u32 low, u32 id) |
| 266 | { |
| 267 | wrmsrl(APIC_BASE_MSR + (APIC_ICR >> 4), ((__u64) id) << 32 | low); |
| 268 | } |
| 269 | |
| 270 | u64 x2apic_icr_read(void) |
| 271 | { |
| 272 | unsigned long val; |
| 273 | |
| 274 | rdmsrl(APIC_BASE_MSR + (APIC_ICR >> 4), val); |
| 275 | return val; |
| 276 | } |
| 277 | |
| 278 | static struct apic_ops x2apic_ops = { |
| 279 | .read = native_apic_msr_read, |
| 280 | .write = native_apic_msr_write, |
| 281 | .icr_read = x2apic_icr_read, |
| 282 | .icr_write = x2apic_icr_write, |
| 283 | .wait_icr_idle = x2apic_wait_icr_idle, |
| 284 | .safe_wait_icr_idle = safe_x2apic_wait_icr_idle, |
| 285 | }; |
| 286 | #endif |
| 287 | |
| 288 | /** |
| 289 | * enable_NMI_through_LVT0 - enable NMI through local vector table 0 |
| 290 | */ |
| 291 | void __cpuinit enable_NMI_through_LVT0(void) |
| 292 | { |
| 293 | unsigned int v; |
| 294 | |
| 295 | /* unmask and set to NMI */ |
| 296 | v = APIC_DM_NMI; |
| 297 | |
| 298 | /* Level triggered for 82489DX (32bit mode) */ |
| 299 | if (!lapic_is_integrated()) |
| 300 | v |= APIC_LVT_LEVEL_TRIGGER; |
| 301 | |
| 302 | apic_write(APIC_LVT0, v); |
| 303 | } |
| 304 | |
| 305 | #ifdef CONFIG_X86_32 |
| 306 | /** |
| 307 | * get_physical_broadcast - Get number of physical broadcast IDs |
| 308 | */ |
| 309 | int get_physical_broadcast(void) |
| 310 | { |
| 311 | return modern_apic() ? 0xff : 0xf; |
| 312 | } |
| 313 | #endif |
| 314 | |
| 315 | /** |
| 316 | * lapic_get_maxlvt - get the maximum number of local vector table entries |
| 317 | */ |
| 318 | int lapic_get_maxlvt(void) |
| 319 | { |
| 320 | unsigned int v; |
| 321 | |
| 322 | v = apic_read(APIC_LVR); |
| 323 | /* |
| 324 | * - we always have APIC integrated on 64bit mode |
| 325 | * - 82489DXs do not report # of LVT entries |
| 326 | */ |
| 327 | return APIC_INTEGRATED(GET_APIC_VERSION(v)) ? GET_APIC_MAXLVT(v) : 2; |
| 328 | } |
| 329 | |
| 330 | /* |
| 331 | * Local APIC timer |
| 332 | */ |
| 333 | |
| 334 | /* Clock divisor */ |
| 335 | #ifdef CONFG_X86_64 |
| 336 | #define APIC_DIVISOR 1 |
| 337 | #else |
| 338 | #define APIC_DIVISOR 16 |
| 339 | #endif |
| 340 | |
| 341 | /* |
| 342 | * This function sets up the local APIC timer, with a timeout of |
| 343 | * 'clocks' APIC bus clock. During calibration we actually call |
| 344 | * this function twice on the boot CPU, once with a bogus timeout |
| 345 | * value, second time for real. The other (noncalibrating) CPUs |
| 346 | * call this function only once, with the real, calibrated value. |
| 347 | * |
| 348 | * We do reads before writes even if unnecessary, to get around the |
| 349 | * P5 APIC double write bug. |
| 350 | */ |
| 351 | static void __setup_APIC_LVTT(unsigned int clocks, int oneshot, int irqen) |
| 352 | { |
| 353 | unsigned int lvtt_value, tmp_value; |
| 354 | |
| 355 | lvtt_value = LOCAL_TIMER_VECTOR; |
| 356 | if (!oneshot) |
| 357 | lvtt_value |= APIC_LVT_TIMER_PERIODIC; |
| 358 | if (!lapic_is_integrated()) |
| 359 | lvtt_value |= SET_APIC_TIMER_BASE(APIC_TIMER_BASE_DIV); |
| 360 | |
| 361 | if (!irqen) |
| 362 | lvtt_value |= APIC_LVT_MASKED; |
| 363 | |
| 364 | apic_write(APIC_LVTT, lvtt_value); |
| 365 | |
| 366 | /* |
| 367 | * Divide PICLK by 16 |
| 368 | */ |
| 369 | tmp_value = apic_read(APIC_TDCR); |
| 370 | apic_write(APIC_TDCR, |
| 371 | (tmp_value & ~(APIC_TDR_DIV_1 | APIC_TDR_DIV_TMBASE)) | |
| 372 | APIC_TDR_DIV_16); |
| 373 | |
| 374 | if (!oneshot) |
| 375 | apic_write(APIC_TMICT, clocks / APIC_DIVISOR); |
| 376 | } |
| 377 | |
| 378 | /* |
| 379 | * Setup extended LVT, AMD specific (K8, family 10h) |
| 380 | * |
| 381 | * Vector mappings are hard coded. On K8 only offset 0 (APIC500) and |
| 382 | * MCE interrupts are supported. Thus MCE offset must be set to 0. |
| 383 | * |
| 384 | * If mask=1, the LVT entry does not generate interrupts while mask=0 |
| 385 | * enables the vector. See also the BKDGs. |
| 386 | */ |
| 387 | |
| 388 | #define APIC_EILVT_LVTOFF_MCE 0 |
| 389 | #define APIC_EILVT_LVTOFF_IBS 1 |
| 390 | |
| 391 | static void setup_APIC_eilvt(u8 lvt_off, u8 vector, u8 msg_type, u8 mask) |
| 392 | { |
| 393 | unsigned long reg = (lvt_off << 4) + APIC_EILVT0; |
| 394 | unsigned int v = (mask << 16) | (msg_type << 8) | vector; |
| 395 | |
| 396 | apic_write(reg, v); |
| 397 | } |
| 398 | |
| 399 | u8 setup_APIC_eilvt_mce(u8 vector, u8 msg_type, u8 mask) |
| 400 | { |
| 401 | setup_APIC_eilvt(APIC_EILVT_LVTOFF_MCE, vector, msg_type, mask); |
| 402 | return APIC_EILVT_LVTOFF_MCE; |
| 403 | } |
| 404 | |
| 405 | u8 setup_APIC_eilvt_ibs(u8 vector, u8 msg_type, u8 mask) |
| 406 | { |
| 407 | setup_APIC_eilvt(APIC_EILVT_LVTOFF_IBS, vector, msg_type, mask); |
| 408 | return APIC_EILVT_LVTOFF_IBS; |
| 409 | } |
| 410 | EXPORT_SYMBOL_GPL(setup_APIC_eilvt_ibs); |
| 411 | |
| 412 | /* |
| 413 | * Program the next event, relative to now |
| 414 | */ |
| 415 | static int lapic_next_event(unsigned long delta, |
| 416 | struct clock_event_device *evt) |
| 417 | { |
| 418 | apic_write(APIC_TMICT, delta); |
| 419 | return 0; |
| 420 | } |
| 421 | |
| 422 | /* |
| 423 | * Setup the lapic timer in periodic or oneshot mode |
| 424 | */ |
| 425 | static void lapic_timer_setup(enum clock_event_mode mode, |
| 426 | struct clock_event_device *evt) |
| 427 | { |
| 428 | unsigned long flags; |
| 429 | unsigned int v; |
| 430 | |
| 431 | /* Lapic used as dummy for broadcast ? */ |
| 432 | if (evt->features & CLOCK_EVT_FEAT_DUMMY) |
| 433 | return; |
| 434 | |
| 435 | local_irq_save(flags); |
| 436 | |
| 437 | switch (mode) { |
| 438 | case CLOCK_EVT_MODE_PERIODIC: |
| 439 | case CLOCK_EVT_MODE_ONESHOT: |
| 440 | __setup_APIC_LVTT(calibration_result, |
| 441 | mode != CLOCK_EVT_MODE_PERIODIC, 1); |
| 442 | break; |
| 443 | case CLOCK_EVT_MODE_UNUSED: |
| 444 | case CLOCK_EVT_MODE_SHUTDOWN: |
| 445 | v = apic_read(APIC_LVTT); |
| 446 | v |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR); |
| 447 | apic_write(APIC_LVTT, v); |
| 448 | break; |
| 449 | case CLOCK_EVT_MODE_RESUME: |
| 450 | /* Nothing to do here */ |
| 451 | break; |
| 452 | } |
| 453 | |
| 454 | local_irq_restore(flags); |
| 455 | } |
| 456 | |
| 457 | /* |
| 458 | * Local APIC timer broadcast function |
| 459 | */ |
| 460 | static void lapic_timer_broadcast(cpumask_t mask) |
| 461 | { |
| 462 | #ifdef CONFIG_SMP |
| 463 | send_IPI_mask(mask, LOCAL_TIMER_VECTOR); |
| 464 | #endif |
| 465 | } |
| 466 | |
| 467 | /* |
| 468 | * Setup the local APIC timer for this CPU. Copy the initilized values |
| 469 | * of the boot CPU and register the clock event in the framework. |
| 470 | */ |
| 471 | static void __cpuinit setup_APIC_timer(void) |
| 472 | { |
| 473 | struct clock_event_device *levt = &__get_cpu_var(lapic_events); |
| 474 | |
| 475 | memcpy(levt, &lapic_clockevent, sizeof(*levt)); |
| 476 | levt->cpumask = cpumask_of_cpu(smp_processor_id()); |
| 477 | |
| 478 | clockevents_register_device(levt); |
| 479 | } |
| 480 | |
| 481 | /* |
| 482 | * In this functions we calibrate APIC bus clocks to the external timer. |
| 483 | * |
| 484 | * We want to do the calibration only once since we want to have local timer |
| 485 | * irqs syncron. CPUs connected by the same APIC bus have the very same bus |
| 486 | * frequency. |
| 487 | * |
| 488 | * This was previously done by reading the PIT/HPET and waiting for a wrap |
| 489 | * around to find out, that a tick has elapsed. I have a box, where the PIT |
| 490 | * readout is broken, so it never gets out of the wait loop again. This was |
| 491 | * also reported by others. |
| 492 | * |
| 493 | * Monitoring the jiffies value is inaccurate and the clockevents |
| 494 | * infrastructure allows us to do a simple substitution of the interrupt |
| 495 | * handler. |
| 496 | * |
| 497 | * The calibration routine also uses the pm_timer when possible, as the PIT |
| 498 | * happens to run way too slow (factor 2.3 on my VAIO CoreDuo, which goes |
| 499 | * back to normal later in the boot process). |
| 500 | */ |
| 501 | |
| 502 | #define LAPIC_CAL_LOOPS (HZ/10) |
| 503 | |
| 504 | static __initdata int lapic_cal_loops = -1; |
| 505 | static __initdata long lapic_cal_t1, lapic_cal_t2; |
| 506 | static __initdata unsigned long long lapic_cal_tsc1, lapic_cal_tsc2; |
| 507 | static __initdata unsigned long lapic_cal_pm1, lapic_cal_pm2; |
| 508 | static __initdata unsigned long lapic_cal_j1, lapic_cal_j2; |
| 509 | |
| 510 | /* |
| 511 | * Temporary interrupt handler. |
| 512 | */ |
| 513 | static void __init lapic_cal_handler(struct clock_event_device *dev) |
| 514 | { |
| 515 | unsigned long long tsc = 0; |
| 516 | long tapic = apic_read(APIC_TMCCT); |
| 517 | unsigned long pm = acpi_pm_read_early(); |
| 518 | |
| 519 | if (cpu_has_tsc) |
| 520 | rdtscll(tsc); |
| 521 | |
| 522 | switch (lapic_cal_loops++) { |
| 523 | case 0: |
| 524 | lapic_cal_t1 = tapic; |
| 525 | lapic_cal_tsc1 = tsc; |
| 526 | lapic_cal_pm1 = pm; |
| 527 | lapic_cal_j1 = jiffies; |
| 528 | break; |
| 529 | |
| 530 | case LAPIC_CAL_LOOPS: |
| 531 | lapic_cal_t2 = tapic; |
| 532 | lapic_cal_tsc2 = tsc; |
| 533 | if (pm < lapic_cal_pm1) |
| 534 | pm += ACPI_PM_OVRRUN; |
| 535 | lapic_cal_pm2 = pm; |
| 536 | lapic_cal_j2 = jiffies; |
| 537 | break; |
| 538 | } |
| 539 | } |
| 540 | |
| 541 | static int __init calibrate_APIC_clock(void) |
| 542 | { |
| 543 | struct clock_event_device *levt = &__get_cpu_var(lapic_events); |
| 544 | const long pm_100ms = PMTMR_TICKS_PER_SEC/10; |
| 545 | const long pm_thresh = pm_100ms/100; |
| 546 | void (*real_handler)(struct clock_event_device *dev); |
| 547 | unsigned long deltaj; |
| 548 | long delta, deltapm; |
| 549 | int pm_referenced = 0; |
| 550 | |
| 551 | local_irq_disable(); |
| 552 | |
| 553 | /* Replace the global interrupt handler */ |
| 554 | real_handler = global_clock_event->event_handler; |
| 555 | global_clock_event->event_handler = lapic_cal_handler; |
| 556 | |
| 557 | /* |
| 558 | * Setup the APIC counter to 1e9. There is no way the lapic |
| 559 | * can underflow in the 100ms detection time frame |
| 560 | */ |
| 561 | __setup_APIC_LVTT(1000000000, 0, 0); |
| 562 | |
| 563 | /* Let the interrupts run */ |
| 564 | local_irq_enable(); |
| 565 | |
| 566 | while (lapic_cal_loops <= LAPIC_CAL_LOOPS) |
| 567 | cpu_relax(); |
| 568 | |
| 569 | local_irq_disable(); |
| 570 | |
| 571 | /* Restore the real event handler */ |
| 572 | global_clock_event->event_handler = real_handler; |
| 573 | |
| 574 | /* Build delta t1-t2 as apic timer counts down */ |
| 575 | delta = lapic_cal_t1 - lapic_cal_t2; |
| 576 | apic_printk(APIC_VERBOSE, "... lapic delta = %ld\n", delta); |
| 577 | |
| 578 | #ifdef CONFIG_X86_PM_TIMER |
| 579 | /* Check, if the PM timer is available */ |
| 580 | deltapm = lapic_cal_pm2 - lapic_cal_pm1; |
| 581 | apic_printk(APIC_VERBOSE, "... PM timer delta = %ld\n", deltapm); |
| 582 | |
| 583 | if (deltapm) { |
| 584 | unsigned long mult; |
| 585 | u64 res; |
| 586 | |
| 587 | mult = clocksource_hz2mult(PMTMR_TICKS_PER_SEC, 22); |
| 588 | |
| 589 | if (deltapm > (pm_100ms - pm_thresh) && |
| 590 | deltapm < (pm_100ms + pm_thresh)) { |
| 591 | apic_printk(APIC_VERBOSE, "... PM timer result ok\n"); |
| 592 | } else { |
| 593 | res = (((u64) deltapm) * mult) >> 22; |
| 594 | do_div(res, 1000000); |
| 595 | printk(KERN_WARNING "APIC calibration not consistent " |
| 596 | "with PM Timer: %ldms instead of 100ms\n", |
| 597 | (long)res); |
| 598 | /* Correct the lapic counter value */ |
| 599 | res = (((u64) delta) * pm_100ms); |
| 600 | do_div(res, deltapm); |
| 601 | printk(KERN_INFO "APIC delta adjusted to PM-Timer: " |
| 602 | "%lu (%ld)\n", (unsigned long) res, delta); |
| 603 | delta = (long) res; |
| 604 | } |
| 605 | pm_referenced = 1; |
| 606 | } |
| 607 | #endif |
| 608 | |
| 609 | /* Calculate the scaled math multiplication factor */ |
| 610 | lapic_clockevent.mult = div_sc(delta, TICK_NSEC * LAPIC_CAL_LOOPS, |
| 611 | lapic_clockevent.shift); |
| 612 | lapic_clockevent.max_delta_ns = |
| 613 | clockevent_delta2ns(0x7FFFFF, &lapic_clockevent); |
| 614 | lapic_clockevent.min_delta_ns = |
| 615 | clockevent_delta2ns(0xF, &lapic_clockevent); |
| 616 | |
| 617 | calibration_result = (delta * APIC_DIVISOR) / LAPIC_CAL_LOOPS; |
| 618 | |
| 619 | apic_printk(APIC_VERBOSE, "..... delta %ld\n", delta); |
| 620 | apic_printk(APIC_VERBOSE, "..... mult: %ld\n", lapic_clockevent.mult); |
| 621 | apic_printk(APIC_VERBOSE, "..... calibration result: %u\n", |
| 622 | calibration_result); |
| 623 | |
| 624 | if (cpu_has_tsc) { |
| 625 | delta = (long)(lapic_cal_tsc2 - lapic_cal_tsc1); |
| 626 | apic_printk(APIC_VERBOSE, "..... CPU clock speed is " |
| 627 | "%ld.%04ld MHz.\n", |
| 628 | (delta / LAPIC_CAL_LOOPS) / (1000000 / HZ), |
| 629 | (delta / LAPIC_CAL_LOOPS) % (1000000 / HZ)); |
| 630 | } |
| 631 | |
| 632 | apic_printk(APIC_VERBOSE, "..... host bus clock speed is " |
| 633 | "%u.%04u MHz.\n", |
| 634 | calibration_result / (1000000 / HZ), |
| 635 | calibration_result % (1000000 / HZ)); |
| 636 | |
| 637 | /* |
| 638 | * Do a sanity check on the APIC calibration result |
| 639 | */ |
| 640 | if (calibration_result < (1000000 / HZ)) { |
| 641 | local_irq_enable(); |
| 642 | printk(KERN_WARNING |
| 643 | "APIC frequency too slow, disabling apic timer\n"); |
| 644 | return -1; |
| 645 | } |
| 646 | |
| 647 | levt->features &= ~CLOCK_EVT_FEAT_DUMMY; |
| 648 | |
| 649 | /* We trust the pm timer based calibration */ |
| 650 | if (!pm_referenced) { |
| 651 | apic_printk(APIC_VERBOSE, "... verify APIC timer\n"); |
| 652 | |
| 653 | /* |
| 654 | * Setup the apic timer manually |
| 655 | */ |
| 656 | levt->event_handler = lapic_cal_handler; |
| 657 | lapic_timer_setup(CLOCK_EVT_MODE_PERIODIC, levt); |
| 658 | lapic_cal_loops = -1; |
| 659 | |
| 660 | /* Let the interrupts run */ |
| 661 | local_irq_enable(); |
| 662 | |
| 663 | while (lapic_cal_loops <= LAPIC_CAL_LOOPS) |
| 664 | cpu_relax(); |
| 665 | |
| 666 | local_irq_disable(); |
| 667 | |
| 668 | /* Stop the lapic timer */ |
| 669 | lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, levt); |
| 670 | |
| 671 | local_irq_enable(); |
| 672 | |
| 673 | /* Jiffies delta */ |
| 674 | deltaj = lapic_cal_j2 - lapic_cal_j1; |
| 675 | apic_printk(APIC_VERBOSE, "... jiffies delta = %lu\n", deltaj); |
| 676 | |
| 677 | /* Check, if the jiffies result is consistent */ |
| 678 | if (deltaj >= LAPIC_CAL_LOOPS-2 && deltaj <= LAPIC_CAL_LOOPS+2) |
| 679 | apic_printk(APIC_VERBOSE, "... jiffies result ok\n"); |
| 680 | else |
| 681 | levt->features |= CLOCK_EVT_FEAT_DUMMY; |
| 682 | } else |
| 683 | local_irq_enable(); |
| 684 | |
| 685 | if (levt->features & CLOCK_EVT_FEAT_DUMMY) { |
| 686 | printk(KERN_WARNING |
| 687 | "APIC timer disabled due to verification failure.\n"); |
| 688 | return -1; |
| 689 | } |
| 690 | |
| 691 | return 0; |
| 692 | } |
| 693 | |
| 694 | /* |
| 695 | * Setup the boot APIC |
| 696 | * |
| 697 | * Calibrate and verify the result. |
| 698 | */ |
| 699 | void __init setup_boot_APIC_clock(void) |
| 700 | { |
| 701 | /* |
| 702 | * The local apic timer can be disabled via the kernel |
| 703 | * commandline or from the CPU detection code. Register the lapic |
| 704 | * timer as a dummy clock event source on SMP systems, so the |
| 705 | * broadcast mechanism is used. On UP systems simply ignore it. |
| 706 | */ |
| 707 | if (disable_apic_timer) { |
| 708 | printk(KERN_INFO "Disabling APIC timer\n"); |
| 709 | /* No broadcast on UP ! */ |
| 710 | if (num_possible_cpus() > 1) { |
| 711 | lapic_clockevent.mult = 1; |
| 712 | setup_APIC_timer(); |
| 713 | } |
| 714 | return; |
| 715 | } |
| 716 | |
| 717 | apic_printk(APIC_VERBOSE, "Using local APIC timer interrupts.\n" |
| 718 | "calibrating APIC timer ...\n"); |
| 719 | |
| 720 | if (calibrate_APIC_clock()) { |
| 721 | /* No broadcast on UP ! */ |
| 722 | if (num_possible_cpus() > 1) |
| 723 | setup_APIC_timer(); |
| 724 | return; |
| 725 | } |
| 726 | |
| 727 | /* |
| 728 | * If nmi_watchdog is set to IO_APIC, we need the |
| 729 | * PIT/HPET going. Otherwise register lapic as a dummy |
| 730 | * device. |
| 731 | */ |
| 732 | if (nmi_watchdog != NMI_IO_APIC) |
| 733 | lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY; |
| 734 | else |
| 735 | printk(KERN_WARNING "APIC timer registered as dummy," |
| 736 | " due to nmi_watchdog=%d!\n", nmi_watchdog); |
| 737 | |
| 738 | /* Setup the lapic or request the broadcast */ |
| 739 | setup_APIC_timer(); |
| 740 | } |
| 741 | |
| 742 | void __cpuinit setup_secondary_APIC_clock(void) |
| 743 | { |
| 744 | setup_APIC_timer(); |
| 745 | } |
| 746 | |
| 747 | /* |
| 748 | * The guts of the apic timer interrupt |
| 749 | */ |
| 750 | static void local_apic_timer_interrupt(void) |
| 751 | { |
| 752 | int cpu = smp_processor_id(); |
| 753 | struct clock_event_device *evt = &per_cpu(lapic_events, cpu); |
| 754 | |
| 755 | /* |
| 756 | * Normally we should not be here till LAPIC has been initialized but |
| 757 | * in some cases like kdump, its possible that there is a pending LAPIC |
| 758 | * timer interrupt from previous kernel's context and is delivered in |
| 759 | * new kernel the moment interrupts are enabled. |
| 760 | * |
| 761 | * Interrupts are enabled early and LAPIC is setup much later, hence |
| 762 | * its possible that when we get here evt->event_handler is NULL. |
| 763 | * Check for event_handler being NULL and discard the interrupt as |
| 764 | * spurious. |
| 765 | */ |
| 766 | if (!evt->event_handler) { |
| 767 | printk(KERN_WARNING |
| 768 | "Spurious LAPIC timer interrupt on cpu %d\n", cpu); |
| 769 | /* Switch it off */ |
| 770 | lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, evt); |
| 771 | return; |
| 772 | } |
| 773 | |
| 774 | /* |
| 775 | * the NMI deadlock-detector uses this. |
| 776 | */ |
| 777 | #ifdef CONFIG_X86_64 |
| 778 | add_pda(apic_timer_irqs, 1); |
| 779 | #else |
| 780 | per_cpu(irq_stat, cpu).apic_timer_irqs++; |
| 781 | #endif |
| 782 | |
| 783 | evt->event_handler(evt); |
| 784 | } |
| 785 | |
| 786 | /* |
| 787 | * Local APIC timer interrupt. This is the most natural way for doing |
| 788 | * local interrupts, but local timer interrupts can be emulated by |
| 789 | * broadcast interrupts too. [in case the hw doesn't support APIC timers] |
| 790 | * |
| 791 | * [ if a single-CPU system runs an SMP kernel then we call the local |
| 792 | * interrupt as well. Thus we cannot inline the local irq ... ] |
| 793 | */ |
| 794 | void smp_apic_timer_interrupt(struct pt_regs *regs) |
| 795 | { |
| 796 | struct pt_regs *old_regs = set_irq_regs(regs); |
| 797 | |
| 798 | /* |
| 799 | * NOTE! We'd better ACK the irq immediately, |
| 800 | * because timer handling can be slow. |
| 801 | */ |
| 802 | ack_APIC_irq(); |
| 803 | /* |
| 804 | * update_process_times() expects us to have done irq_enter(). |
| 805 | * Besides, if we don't timer interrupts ignore the global |
| 806 | * interrupt lock, which is the WrongThing (tm) to do. |
| 807 | */ |
| 808 | #ifdef CONFIG_X86_64 |
| 809 | exit_idle(); |
| 810 | #endif |
| 811 | irq_enter(); |
| 812 | local_apic_timer_interrupt(); |
| 813 | irq_exit(); |
| 814 | |
| 815 | set_irq_regs(old_regs); |
| 816 | } |
| 817 | |
| 818 | int setup_profiling_timer(unsigned int multiplier) |
| 819 | { |
| 820 | return -EINVAL; |
| 821 | } |
| 822 | |
| 823 | /* |
| 824 | * Local APIC start and shutdown |
| 825 | */ |
| 826 | |
| 827 | /** |
| 828 | * clear_local_APIC - shutdown the local APIC |
| 829 | * |
| 830 | * This is called, when a CPU is disabled and before rebooting, so the state of |
| 831 | * the local APIC has no dangling leftovers. Also used to cleanout any BIOS |
| 832 | * leftovers during boot. |
| 833 | */ |
| 834 | void clear_local_APIC(void) |
| 835 | { |
| 836 | int maxlvt; |
| 837 | u32 v; |
| 838 | |
| 839 | /* APIC hasn't been mapped yet */ |
| 840 | if (!apic_phys) |
| 841 | return; |
| 842 | |
| 843 | maxlvt = lapic_get_maxlvt(); |
| 844 | /* |
| 845 | * Masking an LVT entry can trigger a local APIC error |
| 846 | * if the vector is zero. Mask LVTERR first to prevent this. |
| 847 | */ |
| 848 | if (maxlvt >= 3) { |
| 849 | v = ERROR_APIC_VECTOR; /* any non-zero vector will do */ |
| 850 | apic_write(APIC_LVTERR, v | APIC_LVT_MASKED); |
| 851 | } |
| 852 | /* |
| 853 | * Careful: we have to set masks only first to deassert |
| 854 | * any level-triggered sources. |
| 855 | */ |
| 856 | v = apic_read(APIC_LVTT); |
| 857 | apic_write(APIC_LVTT, v | APIC_LVT_MASKED); |
| 858 | v = apic_read(APIC_LVT0); |
| 859 | apic_write(APIC_LVT0, v | APIC_LVT_MASKED); |
| 860 | v = apic_read(APIC_LVT1); |
| 861 | apic_write(APIC_LVT1, v | APIC_LVT_MASKED); |
| 862 | if (maxlvt >= 4) { |
| 863 | v = apic_read(APIC_LVTPC); |
| 864 | apic_write(APIC_LVTPC, v | APIC_LVT_MASKED); |
| 865 | } |
| 866 | |
| 867 | /* lets not touch this if we didn't frob it */ |
| 868 | #if defined(CONFIG_X86_MCE_P4THERMAL) || defined(X86_MCE_INTEL) |
| 869 | if (maxlvt >= 5) { |
| 870 | v = apic_read(APIC_LVTTHMR); |
| 871 | apic_write(APIC_LVTTHMR, v | APIC_LVT_MASKED); |
| 872 | } |
| 873 | #endif |
| 874 | /* |
| 875 | * Clean APIC state for other OSs: |
| 876 | */ |
| 877 | apic_write(APIC_LVTT, APIC_LVT_MASKED); |
| 878 | apic_write(APIC_LVT0, APIC_LVT_MASKED); |
| 879 | apic_write(APIC_LVT1, APIC_LVT_MASKED); |
| 880 | if (maxlvt >= 3) |
| 881 | apic_write(APIC_LVTERR, APIC_LVT_MASKED); |
| 882 | if (maxlvt >= 4) |
| 883 | apic_write(APIC_LVTPC, APIC_LVT_MASKED); |
| 884 | |
| 885 | /* Integrated APIC (!82489DX) ? */ |
| 886 | if (lapic_is_integrated()) { |
| 887 | if (maxlvt > 3) |
| 888 | /* Clear ESR due to Pentium errata 3AP and 11AP */ |
| 889 | apic_write(APIC_ESR, 0); |
| 890 | apic_read(APIC_ESR); |
| 891 | } |
| 892 | } |
| 893 | |
| 894 | /** |
| 895 | * disable_local_APIC - clear and disable the local APIC |
| 896 | */ |
| 897 | void disable_local_APIC(void) |
| 898 | { |
| 899 | unsigned int value; |
| 900 | |
| 901 | clear_local_APIC(); |
| 902 | |
| 903 | /* |
| 904 | * Disable APIC (implies clearing of registers |
| 905 | * for 82489DX!). |
| 906 | */ |
| 907 | value = apic_read(APIC_SPIV); |
| 908 | value &= ~APIC_SPIV_APIC_ENABLED; |
| 909 | apic_write(APIC_SPIV, value); |
| 910 | |
| 911 | #ifdef CONFIG_X86_32 |
| 912 | /* |
| 913 | * When LAPIC was disabled by the BIOS and enabled by the kernel, |
| 914 | * restore the disabled state. |
| 915 | */ |
| 916 | if (enabled_via_apicbase) { |
| 917 | unsigned int l, h; |
| 918 | |
| 919 | rdmsr(MSR_IA32_APICBASE, l, h); |
| 920 | l &= ~MSR_IA32_APICBASE_ENABLE; |
| 921 | wrmsr(MSR_IA32_APICBASE, l, h); |
| 922 | } |
| 923 | #endif |
| 924 | } |
| 925 | |
| 926 | /* |
| 927 | * If Linux enabled the LAPIC against the BIOS default disable it down before |
| 928 | * re-entering the BIOS on shutdown. Otherwise the BIOS may get confused and |
| 929 | * not power-off. Additionally clear all LVT entries before disable_local_APIC |
| 930 | * for the case where Linux didn't enable the LAPIC. |
| 931 | */ |
| 932 | void lapic_shutdown(void) |
| 933 | { |
| 934 | unsigned long flags; |
| 935 | |
| 936 | if (!cpu_has_apic) |
| 937 | return; |
| 938 | |
| 939 | local_irq_save(flags); |
| 940 | |
| 941 | #ifdef CONFIG_X86_32 |
| 942 | if (!enabled_via_apicbase) |
| 943 | clear_local_APIC(); |
| 944 | else |
| 945 | #endif |
| 946 | disable_local_APIC(); |
| 947 | |
| 948 | |
| 949 | local_irq_restore(flags); |
| 950 | } |
| 951 | |
| 952 | /* |
| 953 | * This is to verify that we're looking at a real local APIC. |
| 954 | * Check these against your board if the CPUs aren't getting |
| 955 | * started for no apparent reason. |
| 956 | */ |
| 957 | int __init verify_local_APIC(void) |
| 958 | { |
| 959 | unsigned int reg0, reg1; |
| 960 | |
| 961 | /* |
| 962 | * The version register is read-only in a real APIC. |
| 963 | */ |
| 964 | reg0 = apic_read(APIC_LVR); |
| 965 | apic_printk(APIC_DEBUG, "Getting VERSION: %x\n", reg0); |
| 966 | apic_write(APIC_LVR, reg0 ^ APIC_LVR_MASK); |
| 967 | reg1 = apic_read(APIC_LVR); |
| 968 | apic_printk(APIC_DEBUG, "Getting VERSION: %x\n", reg1); |
| 969 | |
| 970 | /* |
| 971 | * The two version reads above should print the same |
| 972 | * numbers. If the second one is different, then we |
| 973 | * poke at a non-APIC. |
| 974 | */ |
| 975 | if (reg1 != reg0) |
| 976 | return 0; |
| 977 | |
| 978 | /* |
| 979 | * Check if the version looks reasonably. |
| 980 | */ |
| 981 | reg1 = GET_APIC_VERSION(reg0); |
| 982 | if (reg1 == 0x00 || reg1 == 0xff) |
| 983 | return 0; |
| 984 | reg1 = lapic_get_maxlvt(); |
| 985 | if (reg1 < 0x02 || reg1 == 0xff) |
| 986 | return 0; |
| 987 | |
| 988 | /* |
| 989 | * The ID register is read/write in a real APIC. |
| 990 | */ |
| 991 | reg0 = apic_read(APIC_ID); |
| 992 | apic_printk(APIC_DEBUG, "Getting ID: %x\n", reg0); |
| 993 | apic_write(APIC_ID, reg0 ^ APIC_ID_MASK); |
| 994 | reg1 = apic_read(APIC_ID); |
| 995 | apic_printk(APIC_DEBUG, "Getting ID: %x\n", reg1); |
| 996 | apic_write(APIC_ID, reg0); |
| 997 | if (reg1 != (reg0 ^ APIC_ID_MASK)) |
| 998 | return 0; |
| 999 | |
| 1000 | /* |
| 1001 | * The next two are just to see if we have sane values. |
| 1002 | * They're only really relevant if we're in Virtual Wire |
| 1003 | * compatibility mode, but most boxes are anymore. |
| 1004 | */ |
| 1005 | reg0 = apic_read(APIC_LVT0); |
| 1006 | apic_printk(APIC_DEBUG, "Getting LVT0: %x\n", reg0); |
| 1007 | reg1 = apic_read(APIC_LVT1); |
| 1008 | apic_printk(APIC_DEBUG, "Getting LVT1: %x\n", reg1); |
| 1009 | |
| 1010 | return 1; |
| 1011 | } |
| 1012 | |
| 1013 | /** |
| 1014 | * sync_Arb_IDs - synchronize APIC bus arbitration IDs |
| 1015 | */ |
| 1016 | void __init sync_Arb_IDs(void) |
| 1017 | { |
| 1018 | /* |
| 1019 | * Unsupported on P4 - see Intel Dev. Manual Vol. 3, Ch. 8.6.1 And not |
| 1020 | * needed on AMD. |
| 1021 | */ |
| 1022 | if (modern_apic() || boot_cpu_data.x86_vendor == X86_VENDOR_AMD) |
| 1023 | return; |
| 1024 | |
| 1025 | /* |
| 1026 | * Wait for idle. |
| 1027 | */ |
| 1028 | apic_wait_icr_idle(); |
| 1029 | |
| 1030 | apic_printk(APIC_DEBUG, "Synchronizing Arb IDs.\n"); |
| 1031 | apic_write(APIC_ICR, APIC_DEST_ALLINC | |
| 1032 | APIC_INT_LEVELTRIG | APIC_DM_INIT); |
| 1033 | } |
| 1034 | |
| 1035 | /* |
| 1036 | * An initial setup of the virtual wire mode. |
| 1037 | */ |
| 1038 | void __init init_bsp_APIC(void) |
| 1039 | { |
| 1040 | unsigned int value; |
| 1041 | |
| 1042 | /* |
| 1043 | * Don't do the setup now if we have a SMP BIOS as the |
| 1044 | * through-I/O-APIC virtual wire mode might be active. |
| 1045 | */ |
| 1046 | if (smp_found_config || !cpu_has_apic) |
| 1047 | return; |
| 1048 | |
| 1049 | /* |
| 1050 | * Do not trust the local APIC being empty at bootup. |
| 1051 | */ |
| 1052 | clear_local_APIC(); |
| 1053 | |
| 1054 | /* |
| 1055 | * Enable APIC. |
| 1056 | */ |
| 1057 | value = apic_read(APIC_SPIV); |
| 1058 | value &= ~APIC_VECTOR_MASK; |
| 1059 | value |= APIC_SPIV_APIC_ENABLED; |
| 1060 | |
| 1061 | #ifdef CONFIG_X86_32 |
| 1062 | /* This bit is reserved on P4/Xeon and should be cleared */ |
| 1063 | if ((boot_cpu_data.x86_vendor == X86_VENDOR_INTEL) && |
| 1064 | (boot_cpu_data.x86 == 15)) |
| 1065 | value &= ~APIC_SPIV_FOCUS_DISABLED; |
| 1066 | else |
| 1067 | #endif |
| 1068 | value |= APIC_SPIV_FOCUS_DISABLED; |
| 1069 | value |= SPURIOUS_APIC_VECTOR; |
| 1070 | apic_write(APIC_SPIV, value); |
| 1071 | |
| 1072 | /* |
| 1073 | * Set up the virtual wire mode. |
| 1074 | */ |
| 1075 | apic_write(APIC_LVT0, APIC_DM_EXTINT); |
| 1076 | value = APIC_DM_NMI; |
| 1077 | if (!lapic_is_integrated()) /* 82489DX */ |
| 1078 | value |= APIC_LVT_LEVEL_TRIGGER; |
| 1079 | apic_write(APIC_LVT1, value); |
| 1080 | } |
| 1081 | |
| 1082 | static void __cpuinit lapic_setup_esr(void) |
| 1083 | { |
| 1084 | unsigned int oldvalue, value, maxlvt; |
| 1085 | |
| 1086 | if (!lapic_is_integrated()) { |
| 1087 | printk(KERN_INFO "No ESR for 82489DX.\n"); |
| 1088 | return; |
| 1089 | } |
| 1090 | |
| 1091 | if (esr_disable) { |
| 1092 | /* |
| 1093 | * Something untraceable is creating bad interrupts on |
| 1094 | * secondary quads ... for the moment, just leave the |
| 1095 | * ESR disabled - we can't do anything useful with the |
| 1096 | * errors anyway - mbligh |
| 1097 | */ |
| 1098 | printk(KERN_INFO "Leaving ESR disabled.\n"); |
| 1099 | return; |
| 1100 | } |
| 1101 | |
| 1102 | maxlvt = lapic_get_maxlvt(); |
| 1103 | if (maxlvt > 3) /* Due to the Pentium erratum 3AP. */ |
| 1104 | apic_write(APIC_ESR, 0); |
| 1105 | oldvalue = apic_read(APIC_ESR); |
| 1106 | |
| 1107 | /* enables sending errors */ |
| 1108 | value = ERROR_APIC_VECTOR; |
| 1109 | apic_write(APIC_LVTERR, value); |
| 1110 | |
| 1111 | /* |
| 1112 | * spec says clear errors after enabling vector. |
| 1113 | */ |
| 1114 | if (maxlvt > 3) |
| 1115 | apic_write(APIC_ESR, 0); |
| 1116 | value = apic_read(APIC_ESR); |
| 1117 | if (value != oldvalue) |
| 1118 | apic_printk(APIC_VERBOSE, "ESR value before enabling " |
| 1119 | "vector: 0x%08x after: 0x%08x\n", |
| 1120 | oldvalue, value); |
| 1121 | } |
| 1122 | |
| 1123 | |
| 1124 | /** |
| 1125 | * setup_local_APIC - setup the local APIC |
| 1126 | */ |
| 1127 | void __cpuinit setup_local_APIC(void) |
| 1128 | { |
| 1129 | unsigned int value; |
| 1130 | int i, j; |
| 1131 | |
| 1132 | #ifdef CONFIG_X86_32 |
| 1133 | /* Pound the ESR really hard over the head with a big hammer - mbligh */ |
| 1134 | if (lapic_is_integrated() && esr_disable) { |
| 1135 | apic_write(APIC_ESR, 0); |
| 1136 | apic_write(APIC_ESR, 0); |
| 1137 | apic_write(APIC_ESR, 0); |
| 1138 | apic_write(APIC_ESR, 0); |
| 1139 | } |
| 1140 | #endif |
| 1141 | |
| 1142 | preempt_disable(); |
| 1143 | |
| 1144 | /* |
| 1145 | * Double-check whether this APIC is really registered. |
| 1146 | * This is meaningless in clustered apic mode, so we skip it. |
| 1147 | */ |
| 1148 | if (!apic_id_registered()) |
| 1149 | BUG(); |
| 1150 | |
| 1151 | /* |
| 1152 | * Intel recommends to set DFR, LDR and TPR before enabling |
| 1153 | * an APIC. See e.g. "AP-388 82489DX User's Manual" (Intel |
| 1154 | * document number 292116). So here it goes... |
| 1155 | */ |
| 1156 | init_apic_ldr(); |
| 1157 | |
| 1158 | /* |
| 1159 | * Set Task Priority to 'accept all'. We never change this |
| 1160 | * later on. |
| 1161 | */ |
| 1162 | value = apic_read(APIC_TASKPRI); |
| 1163 | value &= ~APIC_TPRI_MASK; |
| 1164 | apic_write(APIC_TASKPRI, value); |
| 1165 | |
| 1166 | /* |
| 1167 | * After a crash, we no longer service the interrupts and a pending |
| 1168 | * interrupt from previous kernel might still have ISR bit set. |
| 1169 | * |
| 1170 | * Most probably by now CPU has serviced that pending interrupt and |
| 1171 | * it might not have done the ack_APIC_irq() because it thought, |
| 1172 | * interrupt came from i8259 as ExtInt. LAPIC did not get EOI so it |
| 1173 | * does not clear the ISR bit and cpu thinks it has already serivced |
| 1174 | * the interrupt. Hence a vector might get locked. It was noticed |
| 1175 | * for timer irq (vector 0x31). Issue an extra EOI to clear ISR. |
| 1176 | */ |
| 1177 | for (i = APIC_ISR_NR - 1; i >= 0; i--) { |
| 1178 | value = apic_read(APIC_ISR + i*0x10); |
| 1179 | for (j = 31; j >= 0; j--) { |
| 1180 | if (value & (1<<j)) |
| 1181 | ack_APIC_irq(); |
| 1182 | } |
| 1183 | } |
| 1184 | |
| 1185 | /* |
| 1186 | * Now that we are all set up, enable the APIC |
| 1187 | */ |
| 1188 | value = apic_read(APIC_SPIV); |
| 1189 | value &= ~APIC_VECTOR_MASK; |
| 1190 | /* |
| 1191 | * Enable APIC |
| 1192 | */ |
| 1193 | value |= APIC_SPIV_APIC_ENABLED; |
| 1194 | |
| 1195 | #ifdef CONFIG_X86_32 |
| 1196 | /* |
| 1197 | * Some unknown Intel IO/APIC (or APIC) errata is biting us with |
| 1198 | * certain networking cards. If high frequency interrupts are |
| 1199 | * happening on a particular IOAPIC pin, plus the IOAPIC routing |
| 1200 | * entry is masked/unmasked at a high rate as well then sooner or |
| 1201 | * later IOAPIC line gets 'stuck', no more interrupts are received |
| 1202 | * from the device. If focus CPU is disabled then the hang goes |
| 1203 | * away, oh well :-( |
| 1204 | * |
| 1205 | * [ This bug can be reproduced easily with a level-triggered |
| 1206 | * PCI Ne2000 networking cards and PII/PIII processors, dual |
| 1207 | * BX chipset. ] |
| 1208 | */ |
| 1209 | /* |
| 1210 | * Actually disabling the focus CPU check just makes the hang less |
| 1211 | * frequent as it makes the interrupt distributon model be more |
| 1212 | * like LRU than MRU (the short-term load is more even across CPUs). |
| 1213 | * See also the comment in end_level_ioapic_irq(). --macro |
| 1214 | */ |
| 1215 | |
| 1216 | /* |
| 1217 | * - enable focus processor (bit==0) |
| 1218 | * - 64bit mode always use processor focus |
| 1219 | * so no need to set it |
| 1220 | */ |
| 1221 | value &= ~APIC_SPIV_FOCUS_DISABLED; |
| 1222 | #endif |
| 1223 | |
| 1224 | /* |
| 1225 | * Set spurious IRQ vector |
| 1226 | */ |
| 1227 | value |= SPURIOUS_APIC_VECTOR; |
| 1228 | apic_write(APIC_SPIV, value); |
| 1229 | |
| 1230 | /* |
| 1231 | * Set up LVT0, LVT1: |
| 1232 | * |
| 1233 | * set up through-local-APIC on the BP's LINT0. This is not |
| 1234 | * strictly necessary in pure symmetric-IO mode, but sometimes |
| 1235 | * we delegate interrupts to the 8259A. |
| 1236 | */ |
| 1237 | /* |
| 1238 | * TODO: set up through-local-APIC from through-I/O-APIC? --macro |
| 1239 | */ |
| 1240 | value = apic_read(APIC_LVT0) & APIC_LVT_MASKED; |
| 1241 | if (!smp_processor_id() && (pic_mode || !value)) { |
| 1242 | value = APIC_DM_EXTINT; |
| 1243 | apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n", |
| 1244 | smp_processor_id()); |
| 1245 | } else { |
| 1246 | value = APIC_DM_EXTINT | APIC_LVT_MASKED; |
| 1247 | apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n", |
| 1248 | smp_processor_id()); |
| 1249 | } |
| 1250 | apic_write(APIC_LVT0, value); |
| 1251 | |
| 1252 | /* |
| 1253 | * only the BP should see the LINT1 NMI signal, obviously. |
| 1254 | */ |
| 1255 | if (!smp_processor_id()) |
| 1256 | value = APIC_DM_NMI; |
| 1257 | else |
| 1258 | value = APIC_DM_NMI | APIC_LVT_MASKED; |
| 1259 | if (!lapic_is_integrated()) /* 82489DX */ |
| 1260 | value |= APIC_LVT_LEVEL_TRIGGER; |
| 1261 | apic_write(APIC_LVT1, value); |
| 1262 | |
| 1263 | preempt_enable(); |
| 1264 | } |
| 1265 | |
| 1266 | void __cpuinit end_local_APIC_setup(void) |
| 1267 | { |
| 1268 | lapic_setup_esr(); |
| 1269 | |
| 1270 | #ifdef CONFIG_X86_32 |
| 1271 | { |
| 1272 | unsigned int value; |
| 1273 | /* Disable the local apic timer */ |
| 1274 | value = apic_read(APIC_LVTT); |
| 1275 | value |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR); |
| 1276 | apic_write(APIC_LVTT, value); |
| 1277 | } |
| 1278 | #endif |
| 1279 | |
| 1280 | setup_apic_nmi_watchdog(NULL); |
| 1281 | apic_pm_activate(); |
| 1282 | } |
| 1283 | |
| 1284 | #ifdef HAVE_X2APIC |
| 1285 | void check_x2apic(void) |
| 1286 | { |
| 1287 | int msr, msr2; |
| 1288 | |
| 1289 | rdmsr(MSR_IA32_APICBASE, msr, msr2); |
| 1290 | |
| 1291 | if (msr & X2APIC_ENABLE) { |
| 1292 | printk("x2apic enabled by BIOS, switching to x2apic ops\n"); |
| 1293 | x2apic_preenabled = x2apic = 1; |
| 1294 | apic_ops = &x2apic_ops; |
| 1295 | } |
| 1296 | } |
| 1297 | |
| 1298 | void enable_x2apic(void) |
| 1299 | { |
| 1300 | int msr, msr2; |
| 1301 | |
| 1302 | rdmsr(MSR_IA32_APICBASE, msr, msr2); |
| 1303 | if (!(msr & X2APIC_ENABLE)) { |
| 1304 | printk("Enabling x2apic\n"); |
| 1305 | wrmsr(MSR_IA32_APICBASE, msr | X2APIC_ENABLE, 0); |
| 1306 | } |
| 1307 | } |
| 1308 | |
| 1309 | void enable_IR_x2apic(void) |
| 1310 | { |
| 1311 | #ifdef CONFIG_INTR_REMAP |
| 1312 | int ret; |
| 1313 | unsigned long flags; |
| 1314 | |
| 1315 | if (!cpu_has_x2apic) |
| 1316 | return; |
| 1317 | |
| 1318 | if (!x2apic_preenabled && disable_x2apic) { |
| 1319 | printk(KERN_INFO |
| 1320 | "Skipped enabling x2apic and Interrupt-remapping " |
| 1321 | "because of nox2apic\n"); |
| 1322 | return; |
| 1323 | } |
| 1324 | |
| 1325 | if (x2apic_preenabled && disable_x2apic) |
| 1326 | panic("Bios already enabled x2apic, can't enforce nox2apic"); |
| 1327 | |
| 1328 | if (!x2apic_preenabled && skip_ioapic_setup) { |
| 1329 | printk(KERN_INFO |
| 1330 | "Skipped enabling x2apic and Interrupt-remapping " |
| 1331 | "because of skipping io-apic setup\n"); |
| 1332 | return; |
| 1333 | } |
| 1334 | |
| 1335 | ret = dmar_table_init(); |
| 1336 | if (ret) { |
| 1337 | printk(KERN_INFO |
| 1338 | "dmar_table_init() failed with %d:\n", ret); |
| 1339 | |
| 1340 | if (x2apic_preenabled) |
| 1341 | panic("x2apic enabled by bios. But IR enabling failed"); |
| 1342 | else |
| 1343 | printk(KERN_INFO |
| 1344 | "Not enabling x2apic,Intr-remapping\n"); |
| 1345 | return; |
| 1346 | } |
| 1347 | |
| 1348 | local_irq_save(flags); |
| 1349 | mask_8259A(); |
| 1350 | save_mask_IO_APIC_setup(); |
| 1351 | |
| 1352 | ret = enable_intr_remapping(1); |
| 1353 | |
| 1354 | if (ret && x2apic_preenabled) { |
| 1355 | local_irq_restore(flags); |
| 1356 | panic("x2apic enabled by bios. But IR enabling failed"); |
| 1357 | } |
| 1358 | |
| 1359 | if (ret) |
| 1360 | goto end; |
| 1361 | |
| 1362 | if (!x2apic) { |
| 1363 | x2apic = 1; |
| 1364 | apic_ops = &x2apic_ops; |
| 1365 | enable_x2apic(); |
| 1366 | } |
| 1367 | end: |
| 1368 | if (ret) |
| 1369 | /* |
| 1370 | * IR enabling failed |
| 1371 | */ |
| 1372 | restore_IO_APIC_setup(); |
| 1373 | else |
| 1374 | reinit_intr_remapped_IO_APIC(x2apic_preenabled); |
| 1375 | |
| 1376 | unmask_8259A(); |
| 1377 | local_irq_restore(flags); |
| 1378 | |
| 1379 | if (!ret) { |
| 1380 | if (!x2apic_preenabled) |
| 1381 | printk(KERN_INFO |
| 1382 | "Enabled x2apic and interrupt-remapping\n"); |
| 1383 | else |
| 1384 | printk(KERN_INFO |
| 1385 | "Enabled Interrupt-remapping\n"); |
| 1386 | } else |
| 1387 | printk(KERN_ERR |
| 1388 | "Failed to enable Interrupt-remapping and x2apic\n"); |
| 1389 | #else |
| 1390 | if (!cpu_has_x2apic) |
| 1391 | return; |
| 1392 | |
| 1393 | if (x2apic_preenabled) |
| 1394 | panic("x2apic enabled prior OS handover," |
| 1395 | " enable CONFIG_INTR_REMAP"); |
| 1396 | |
| 1397 | printk(KERN_INFO "Enable CONFIG_INTR_REMAP for enabling intr-remapping " |
| 1398 | " and x2apic\n"); |
| 1399 | #endif |
| 1400 | |
| 1401 | return; |
| 1402 | } |
| 1403 | #endif /* HAVE_X2APIC */ |
| 1404 | |
| 1405 | #ifdef CONFIG_X86_64 |
| 1406 | /* |
| 1407 | * Detect and enable local APICs on non-SMP boards. |
| 1408 | * Original code written by Keir Fraser. |
| 1409 | * On AMD64 we trust the BIOS - if it says no APIC it is likely |
| 1410 | * not correctly set up (usually the APIC timer won't work etc.) |
| 1411 | */ |
| 1412 | static int __init detect_init_APIC(void) |
| 1413 | { |
| 1414 | if (!cpu_has_apic) { |
| 1415 | printk(KERN_INFO "No local APIC present\n"); |
| 1416 | return -1; |
| 1417 | } |
| 1418 | |
| 1419 | mp_lapic_addr = APIC_DEFAULT_PHYS_BASE; |
| 1420 | boot_cpu_physical_apicid = 0; |
| 1421 | return 0; |
| 1422 | } |
| 1423 | #else |
| 1424 | /* |
| 1425 | * Detect and initialize APIC |
| 1426 | */ |
| 1427 | static int __init detect_init_APIC(void) |
| 1428 | { |
| 1429 | u32 h, l, features; |
| 1430 | |
| 1431 | /* Disabled by kernel option? */ |
| 1432 | if (disable_apic) |
| 1433 | return -1; |
| 1434 | |
| 1435 | switch (boot_cpu_data.x86_vendor) { |
| 1436 | case X86_VENDOR_AMD: |
| 1437 | if ((boot_cpu_data.x86 == 6 && boot_cpu_data.x86_model > 1) || |
| 1438 | (boot_cpu_data.x86 == 15)) |
| 1439 | break; |
| 1440 | goto no_apic; |
| 1441 | case X86_VENDOR_INTEL: |
| 1442 | if (boot_cpu_data.x86 == 6 || boot_cpu_data.x86 == 15 || |
| 1443 | (boot_cpu_data.x86 == 5 && cpu_has_apic)) |
| 1444 | break; |
| 1445 | goto no_apic; |
| 1446 | default: |
| 1447 | goto no_apic; |
| 1448 | } |
| 1449 | |
| 1450 | if (!cpu_has_apic) { |
| 1451 | /* |
| 1452 | * Over-ride BIOS and try to enable the local APIC only if |
| 1453 | * "lapic" specified. |
| 1454 | */ |
| 1455 | if (!force_enable_local_apic) { |
| 1456 | printk(KERN_INFO "Local APIC disabled by BIOS -- " |
| 1457 | "you can enable it with \"lapic\"\n"); |
| 1458 | return -1; |
| 1459 | } |
| 1460 | /* |
| 1461 | * Some BIOSes disable the local APIC in the APIC_BASE |
| 1462 | * MSR. This can only be done in software for Intel P6 or later |
| 1463 | * and AMD K7 (Model > 1) or later. |
| 1464 | */ |
| 1465 | rdmsr(MSR_IA32_APICBASE, l, h); |
| 1466 | if (!(l & MSR_IA32_APICBASE_ENABLE)) { |
| 1467 | printk(KERN_INFO |
| 1468 | "Local APIC disabled by BIOS -- reenabling.\n"); |
| 1469 | l &= ~MSR_IA32_APICBASE_BASE; |
| 1470 | l |= MSR_IA32_APICBASE_ENABLE | APIC_DEFAULT_PHYS_BASE; |
| 1471 | wrmsr(MSR_IA32_APICBASE, l, h); |
| 1472 | enabled_via_apicbase = 1; |
| 1473 | } |
| 1474 | } |
| 1475 | /* |
| 1476 | * The APIC feature bit should now be enabled |
| 1477 | * in `cpuid' |
| 1478 | */ |
| 1479 | features = cpuid_edx(1); |
| 1480 | if (!(features & (1 << X86_FEATURE_APIC))) { |
| 1481 | printk(KERN_WARNING "Could not enable APIC!\n"); |
| 1482 | return -1; |
| 1483 | } |
| 1484 | set_cpu_cap(&boot_cpu_data, X86_FEATURE_APIC); |
| 1485 | mp_lapic_addr = APIC_DEFAULT_PHYS_BASE; |
| 1486 | |
| 1487 | /* The BIOS may have set up the APIC at some other address */ |
| 1488 | rdmsr(MSR_IA32_APICBASE, l, h); |
| 1489 | if (l & MSR_IA32_APICBASE_ENABLE) |
| 1490 | mp_lapic_addr = l & MSR_IA32_APICBASE_BASE; |
| 1491 | |
| 1492 | printk(KERN_INFO "Found and enabled local APIC!\n"); |
| 1493 | |
| 1494 | apic_pm_activate(); |
| 1495 | |
| 1496 | return 0; |
| 1497 | |
| 1498 | no_apic: |
| 1499 | printk(KERN_INFO "No local APIC present or hardware disabled\n"); |
| 1500 | return -1; |
| 1501 | } |
| 1502 | #endif |
| 1503 | |
| 1504 | #ifdef CONFIG_X86_64 |
| 1505 | void __init early_init_lapic_mapping(void) |
| 1506 | { |
| 1507 | unsigned long phys_addr; |
| 1508 | |
| 1509 | /* |
| 1510 | * If no local APIC can be found then go out |
| 1511 | * : it means there is no mpatable and MADT |
| 1512 | */ |
| 1513 | if (!smp_found_config) |
| 1514 | return; |
| 1515 | |
| 1516 | phys_addr = mp_lapic_addr; |
| 1517 | |
| 1518 | set_fixmap_nocache(FIX_APIC_BASE, phys_addr); |
| 1519 | apic_printk(APIC_VERBOSE, "mapped APIC to %16lx (%16lx)\n", |
| 1520 | APIC_BASE, phys_addr); |
| 1521 | |
| 1522 | /* |
| 1523 | * Fetch the APIC ID of the BSP in case we have a |
| 1524 | * default configuration (or the MP table is broken). |
| 1525 | */ |
| 1526 | boot_cpu_physical_apicid = read_apic_id(); |
| 1527 | } |
| 1528 | #endif |
| 1529 | |
| 1530 | /** |
| 1531 | * init_apic_mappings - initialize APIC mappings |
| 1532 | */ |
| 1533 | void __init init_apic_mappings(void) |
| 1534 | { |
| 1535 | #ifdef HAVE_X2APIC |
| 1536 | if (x2apic) { |
| 1537 | boot_cpu_physical_apicid = read_apic_id(); |
| 1538 | return; |
| 1539 | } |
| 1540 | #endif |
| 1541 | |
| 1542 | /* |
| 1543 | * If no local APIC can be found then set up a fake all |
| 1544 | * zeroes page to simulate the local APIC and another |
| 1545 | * one for the IO-APIC. |
| 1546 | */ |
| 1547 | if (!smp_found_config && detect_init_APIC()) { |
| 1548 | apic_phys = (unsigned long) alloc_bootmem_pages(PAGE_SIZE); |
| 1549 | apic_phys = __pa(apic_phys); |
| 1550 | } else |
| 1551 | apic_phys = mp_lapic_addr; |
| 1552 | |
| 1553 | set_fixmap_nocache(FIX_APIC_BASE, apic_phys); |
| 1554 | apic_printk(APIC_VERBOSE, "mapped APIC to %08lx (%08lx)\n", |
| 1555 | APIC_BASE, apic_phys); |
| 1556 | |
| 1557 | /* |
| 1558 | * Fetch the APIC ID of the BSP in case we have a |
| 1559 | * default configuration (or the MP table is broken). |
| 1560 | */ |
| 1561 | if (boot_cpu_physical_apicid == -1U) |
| 1562 | boot_cpu_physical_apicid = read_apic_id(); |
| 1563 | } |
| 1564 | |
| 1565 | /* |
| 1566 | * This initializes the IO-APIC and APIC hardware if this is |
| 1567 | * a UP kernel. |
| 1568 | */ |
| 1569 | int apic_version[MAX_APICS]; |
| 1570 | |
| 1571 | int __init APIC_init_uniprocessor(void) |
| 1572 | { |
| 1573 | #ifdef CONFIG_X86_64 |
| 1574 | if (disable_apic) { |
| 1575 | printk(KERN_INFO "Apic disabled\n"); |
| 1576 | return -1; |
| 1577 | } |
| 1578 | if (!cpu_has_apic) { |
| 1579 | disable_apic = 1; |
| 1580 | printk(KERN_INFO "Apic disabled by BIOS\n"); |
| 1581 | return -1; |
| 1582 | } |
| 1583 | #else |
| 1584 | if (!smp_found_config && !cpu_has_apic) |
| 1585 | return -1; |
| 1586 | |
| 1587 | /* |
| 1588 | * Complain if the BIOS pretends there is one. |
| 1589 | */ |
| 1590 | if (!cpu_has_apic && |
| 1591 | APIC_INTEGRATED(apic_version[boot_cpu_physical_apicid])) { |
| 1592 | printk(KERN_ERR "BIOS bug, local APIC 0x%x not detected!...\n", |
| 1593 | boot_cpu_physical_apicid); |
| 1594 | clear_cpu_cap(&boot_cpu_data, X86_FEATURE_APIC); |
| 1595 | return -1; |
| 1596 | } |
| 1597 | #endif |
| 1598 | |
| 1599 | #ifdef HAVE_X2APIC |
| 1600 | enable_IR_x2apic(); |
| 1601 | #endif |
| 1602 | #ifdef CONFIG_X86_64 |
| 1603 | setup_apic_routing(); |
| 1604 | #endif |
| 1605 | |
| 1606 | verify_local_APIC(); |
| 1607 | connect_bsp_APIC(); |
| 1608 | |
| 1609 | #ifdef CONFIG_X86_64 |
| 1610 | apic_write(APIC_ID, SET_APIC_ID(boot_cpu_physical_apicid)); |
| 1611 | #else |
| 1612 | /* |
| 1613 | * Hack: In case of kdump, after a crash, kernel might be booting |
| 1614 | * on a cpu with non-zero lapic id. But boot_cpu_physical_apicid |
| 1615 | * might be zero if read from MP tables. Get it from LAPIC. |
| 1616 | */ |
| 1617 | # ifdef CONFIG_CRASH_DUMP |
| 1618 | boot_cpu_physical_apicid = read_apic_id(); |
| 1619 | # endif |
| 1620 | #endif |
| 1621 | physid_set_mask_of_physid(boot_cpu_physical_apicid, &phys_cpu_present_map); |
| 1622 | setup_local_APIC(); |
| 1623 | |
| 1624 | #ifdef CONFIG_X86_64 |
| 1625 | /* |
| 1626 | * Now enable IO-APICs, actually call clear_IO_APIC |
| 1627 | * We need clear_IO_APIC before enabling vector on BP |
| 1628 | */ |
| 1629 | if (!skip_ioapic_setup && nr_ioapics) |
| 1630 | enable_IO_APIC(); |
| 1631 | #endif |
| 1632 | |
| 1633 | #ifdef CONFIG_X86_IO_APIC |
| 1634 | if (!smp_found_config || skip_ioapic_setup || !nr_ioapics) |
| 1635 | #endif |
| 1636 | localise_nmi_watchdog(); |
| 1637 | end_local_APIC_setup(); |
| 1638 | |
| 1639 | #ifdef CONFIG_X86_IO_APIC |
| 1640 | if (smp_found_config && !skip_ioapic_setup && nr_ioapics) |
| 1641 | setup_IO_APIC(); |
| 1642 | # ifdef CONFIG_X86_64 |
| 1643 | else |
| 1644 | nr_ioapics = 0; |
| 1645 | # endif |
| 1646 | #endif |
| 1647 | |
| 1648 | #ifdef CONFIG_X86_64 |
| 1649 | setup_boot_APIC_clock(); |
| 1650 | check_nmi_watchdog(); |
| 1651 | #else |
| 1652 | setup_boot_clock(); |
| 1653 | #endif |
| 1654 | |
| 1655 | return 0; |
| 1656 | } |
| 1657 | |
| 1658 | /* |
| 1659 | * Local APIC interrupts |
| 1660 | */ |
| 1661 | |
| 1662 | /* |
| 1663 | * This interrupt should _never_ happen with our APIC/SMP architecture |
| 1664 | */ |
| 1665 | void smp_spurious_interrupt(struct pt_regs *regs) |
| 1666 | { |
| 1667 | u32 v; |
| 1668 | |
| 1669 | #ifdef CONFIG_X86_64 |
| 1670 | exit_idle(); |
| 1671 | #endif |
| 1672 | irq_enter(); |
| 1673 | /* |
| 1674 | * Check if this really is a spurious interrupt and ACK it |
| 1675 | * if it is a vectored one. Just in case... |
| 1676 | * Spurious interrupts should not be ACKed. |
| 1677 | */ |
| 1678 | v = apic_read(APIC_ISR + ((SPURIOUS_APIC_VECTOR & ~0x1f) >> 1)); |
| 1679 | if (v & (1 << (SPURIOUS_APIC_VECTOR & 0x1f))) |
| 1680 | ack_APIC_irq(); |
| 1681 | |
| 1682 | #ifdef CONFIG_X86_64 |
| 1683 | add_pda(irq_spurious_count, 1); |
| 1684 | #else |
| 1685 | /* see sw-dev-man vol 3, chapter 7.4.13.5 */ |
| 1686 | printk(KERN_INFO "spurious APIC interrupt on CPU#%d, " |
| 1687 | "should never happen.\n", smp_processor_id()); |
| 1688 | __get_cpu_var(irq_stat).irq_spurious_count++; |
| 1689 | #endif |
| 1690 | irq_exit(); |
| 1691 | } |
| 1692 | |
| 1693 | /* |
| 1694 | * This interrupt should never happen with our APIC/SMP architecture |
| 1695 | */ |
| 1696 | void smp_error_interrupt(struct pt_regs *regs) |
| 1697 | { |
| 1698 | u32 v, v1; |
| 1699 | |
| 1700 | #ifdef CONFIG_X86_64 |
| 1701 | exit_idle(); |
| 1702 | #endif |
| 1703 | irq_enter(); |
| 1704 | /* First tickle the hardware, only then report what went on. -- REW */ |
| 1705 | v = apic_read(APIC_ESR); |
| 1706 | apic_write(APIC_ESR, 0); |
| 1707 | v1 = apic_read(APIC_ESR); |
| 1708 | ack_APIC_irq(); |
| 1709 | atomic_inc(&irq_err_count); |
| 1710 | |
| 1711 | /* Here is what the APIC error bits mean: |
| 1712 | 0: Send CS error |
| 1713 | 1: Receive CS error |
| 1714 | 2: Send accept error |
| 1715 | 3: Receive accept error |
| 1716 | 4: Reserved |
| 1717 | 5: Send illegal vector |
| 1718 | 6: Received illegal vector |
| 1719 | 7: Illegal register address |
| 1720 | */ |
| 1721 | printk(KERN_DEBUG "APIC error on CPU%d: %02x(%02x)\n", |
| 1722 | smp_processor_id(), v , v1); |
| 1723 | irq_exit(); |
| 1724 | } |
| 1725 | |
| 1726 | /** |
| 1727 | * connect_bsp_APIC - attach the APIC to the interrupt system |
| 1728 | */ |
| 1729 | void __init connect_bsp_APIC(void) |
| 1730 | { |
| 1731 | #ifdef CONFIG_X86_32 |
| 1732 | if (pic_mode) { |
| 1733 | /* |
| 1734 | * Do not trust the local APIC being empty at bootup. |
| 1735 | */ |
| 1736 | clear_local_APIC(); |
| 1737 | /* |
| 1738 | * PIC mode, enable APIC mode in the IMCR, i.e. connect BSP's |
| 1739 | * local APIC to INT and NMI lines. |
| 1740 | */ |
| 1741 | apic_printk(APIC_VERBOSE, "leaving PIC mode, " |
| 1742 | "enabling APIC mode.\n"); |
| 1743 | outb(0x70, 0x22); |
| 1744 | outb(0x01, 0x23); |
| 1745 | } |
| 1746 | #endif |
| 1747 | enable_apic_mode(); |
| 1748 | } |
| 1749 | |
| 1750 | /** |
| 1751 | * disconnect_bsp_APIC - detach the APIC from the interrupt system |
| 1752 | * @virt_wire_setup: indicates, whether virtual wire mode is selected |
| 1753 | * |
| 1754 | * Virtual wire mode is necessary to deliver legacy interrupts even when the |
| 1755 | * APIC is disabled. |
| 1756 | */ |
| 1757 | void disconnect_bsp_APIC(int virt_wire_setup) |
| 1758 | { |
| 1759 | unsigned int value; |
| 1760 | |
| 1761 | #ifdef CONFIG_X86_32 |
| 1762 | if (pic_mode) { |
| 1763 | /* |
| 1764 | * Put the board back into PIC mode (has an effect only on |
| 1765 | * certain older boards). Note that APIC interrupts, including |
| 1766 | * IPIs, won't work beyond this point! The only exception are |
| 1767 | * INIT IPIs. |
| 1768 | */ |
| 1769 | apic_printk(APIC_VERBOSE, "disabling APIC mode, " |
| 1770 | "entering PIC mode.\n"); |
| 1771 | outb(0x70, 0x22); |
| 1772 | outb(0x00, 0x23); |
| 1773 | return; |
| 1774 | } |
| 1775 | #endif |
| 1776 | |
| 1777 | /* Go back to Virtual Wire compatibility mode */ |
| 1778 | |
| 1779 | /* For the spurious interrupt use vector F, and enable it */ |
| 1780 | value = apic_read(APIC_SPIV); |
| 1781 | value &= ~APIC_VECTOR_MASK; |
| 1782 | value |= APIC_SPIV_APIC_ENABLED; |
| 1783 | value |= 0xf; |
| 1784 | apic_write(APIC_SPIV, value); |
| 1785 | |
| 1786 | if (!virt_wire_setup) { |
| 1787 | /* |
| 1788 | * For LVT0 make it edge triggered, active high, |
| 1789 | * external and enabled |
| 1790 | */ |
| 1791 | value = apic_read(APIC_LVT0); |
| 1792 | value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING | |
| 1793 | APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR | |
| 1794 | APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED); |
| 1795 | value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING; |
| 1796 | value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_EXTINT); |
| 1797 | apic_write(APIC_LVT0, value); |
| 1798 | } else { |
| 1799 | /* Disable LVT0 */ |
| 1800 | apic_write(APIC_LVT0, APIC_LVT_MASKED); |
| 1801 | } |
| 1802 | |
| 1803 | /* |
| 1804 | * For LVT1 make it edge triggered, active high, |
| 1805 | * nmi and enabled |
| 1806 | */ |
| 1807 | value = apic_read(APIC_LVT1); |
| 1808 | value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING | |
| 1809 | APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR | |
| 1810 | APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED); |
| 1811 | value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING; |
| 1812 | value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_NMI); |
| 1813 | apic_write(APIC_LVT1, value); |
| 1814 | } |
| 1815 | |
| 1816 | void __cpuinit generic_processor_info(int apicid, int version) |
| 1817 | { |
| 1818 | int cpu; |
| 1819 | cpumask_t tmp_map; |
| 1820 | |
| 1821 | /* |
| 1822 | * Validate version |
| 1823 | */ |
| 1824 | if (version == 0x0) { |
| 1825 | printk(KERN_WARNING "BIOS bug, APIC version is 0 for CPU#%d! " |
| 1826 | "fixing up to 0x10. (tell your hw vendor)\n", |
| 1827 | version); |
| 1828 | version = 0x10; |
| 1829 | } |
| 1830 | apic_version[apicid] = version; |
| 1831 | |
| 1832 | if (num_processors >= NR_CPUS) { |
| 1833 | printk(KERN_WARNING "WARNING: NR_CPUS limit of %i reached." |
| 1834 | " Processor ignored.\n", NR_CPUS); |
| 1835 | return; |
| 1836 | } |
| 1837 | |
| 1838 | num_processors++; |
| 1839 | cpus_complement(tmp_map, cpu_present_map); |
| 1840 | cpu = first_cpu(tmp_map); |
| 1841 | |
| 1842 | physid_set(apicid, phys_cpu_present_map); |
| 1843 | if (apicid == boot_cpu_physical_apicid) { |
| 1844 | /* |
| 1845 | * x86_bios_cpu_apicid is required to have processors listed |
| 1846 | * in same order as logical cpu numbers. Hence the first |
| 1847 | * entry is BSP, and so on. |
| 1848 | */ |
| 1849 | cpu = 0; |
| 1850 | } |
| 1851 | if (apicid > max_physical_apicid) |
| 1852 | max_physical_apicid = apicid; |
| 1853 | |
| 1854 | #ifdef CONFIG_X86_32 |
| 1855 | /* |
| 1856 | * Would be preferable to switch to bigsmp when CONFIG_HOTPLUG_CPU=y |
| 1857 | * but we need to work other dependencies like SMP_SUSPEND etc |
| 1858 | * before this can be done without some confusion. |
| 1859 | * if (CPU_HOTPLUG_ENABLED || num_processors > 8) |
| 1860 | * - Ashok Raj <ashok.raj@intel.com> |
| 1861 | */ |
| 1862 | if (max_physical_apicid >= 8) { |
| 1863 | switch (boot_cpu_data.x86_vendor) { |
| 1864 | case X86_VENDOR_INTEL: |
| 1865 | if (!APIC_XAPIC(version)) { |
| 1866 | def_to_bigsmp = 0; |
| 1867 | break; |
| 1868 | } |
| 1869 | /* If P4 and above fall through */ |
| 1870 | case X86_VENDOR_AMD: |
| 1871 | def_to_bigsmp = 1; |
| 1872 | } |
| 1873 | } |
| 1874 | #endif |
| 1875 | |
| 1876 | #if defined(CONFIG_X86_SMP) || defined(CONFIG_X86_64) |
| 1877 | /* are we being called early in kernel startup? */ |
| 1878 | if (early_per_cpu_ptr(x86_cpu_to_apicid)) { |
| 1879 | u16 *cpu_to_apicid = early_per_cpu_ptr(x86_cpu_to_apicid); |
| 1880 | u16 *bios_cpu_apicid = early_per_cpu_ptr(x86_bios_cpu_apicid); |
| 1881 | |
| 1882 | cpu_to_apicid[cpu] = apicid; |
| 1883 | bios_cpu_apicid[cpu] = apicid; |
| 1884 | } else { |
| 1885 | per_cpu(x86_cpu_to_apicid, cpu) = apicid; |
| 1886 | per_cpu(x86_bios_cpu_apicid, cpu) = apicid; |
| 1887 | } |
| 1888 | #endif |
| 1889 | |
| 1890 | cpu_set(cpu, cpu_possible_map); |
| 1891 | cpu_set(cpu, cpu_present_map); |
| 1892 | } |
| 1893 | |
| 1894 | #ifdef CONFIG_X86_64 |
| 1895 | int hard_smp_processor_id(void) |
| 1896 | { |
| 1897 | return read_apic_id(); |
| 1898 | } |
| 1899 | #endif |
| 1900 | |
| 1901 | /* |
| 1902 | * Power management |
| 1903 | */ |
| 1904 | #ifdef CONFIG_PM |
| 1905 | |
| 1906 | static struct { |
| 1907 | /* |
| 1908 | * 'active' is true if the local APIC was enabled by us and |
| 1909 | * not the BIOS; this signifies that we are also responsible |
| 1910 | * for disabling it before entering apm/acpi suspend |
| 1911 | */ |
| 1912 | int active; |
| 1913 | /* r/w apic fields */ |
| 1914 | unsigned int apic_id; |
| 1915 | unsigned int apic_taskpri; |
| 1916 | unsigned int apic_ldr; |
| 1917 | unsigned int apic_dfr; |
| 1918 | unsigned int apic_spiv; |
| 1919 | unsigned int apic_lvtt; |
| 1920 | unsigned int apic_lvtpc; |
| 1921 | unsigned int apic_lvt0; |
| 1922 | unsigned int apic_lvt1; |
| 1923 | unsigned int apic_lvterr; |
| 1924 | unsigned int apic_tmict; |
| 1925 | unsigned int apic_tdcr; |
| 1926 | unsigned int apic_thmr; |
| 1927 | } apic_pm_state; |
| 1928 | |
| 1929 | static int lapic_suspend(struct sys_device *dev, pm_message_t state) |
| 1930 | { |
| 1931 | unsigned long flags; |
| 1932 | int maxlvt; |
| 1933 | |
| 1934 | if (!apic_pm_state.active) |
| 1935 | return 0; |
| 1936 | |
| 1937 | maxlvt = lapic_get_maxlvt(); |
| 1938 | |
| 1939 | apic_pm_state.apic_id = apic_read(APIC_ID); |
| 1940 | apic_pm_state.apic_taskpri = apic_read(APIC_TASKPRI); |
| 1941 | apic_pm_state.apic_ldr = apic_read(APIC_LDR); |
| 1942 | apic_pm_state.apic_dfr = apic_read(APIC_DFR); |
| 1943 | apic_pm_state.apic_spiv = apic_read(APIC_SPIV); |
| 1944 | apic_pm_state.apic_lvtt = apic_read(APIC_LVTT); |
| 1945 | if (maxlvt >= 4) |
| 1946 | apic_pm_state.apic_lvtpc = apic_read(APIC_LVTPC); |
| 1947 | apic_pm_state.apic_lvt0 = apic_read(APIC_LVT0); |
| 1948 | apic_pm_state.apic_lvt1 = apic_read(APIC_LVT1); |
| 1949 | apic_pm_state.apic_lvterr = apic_read(APIC_LVTERR); |
| 1950 | apic_pm_state.apic_tmict = apic_read(APIC_TMICT); |
| 1951 | apic_pm_state.apic_tdcr = apic_read(APIC_TDCR); |
| 1952 | #if defined(CONFIG_X86_MCE_P4THERMAL) || defined(CONFIG_X86_MCE_INTEL) |
| 1953 | if (maxlvt >= 5) |
| 1954 | apic_pm_state.apic_thmr = apic_read(APIC_LVTTHMR); |
| 1955 | #endif |
| 1956 | |
| 1957 | local_irq_save(flags); |
| 1958 | disable_local_APIC(); |
| 1959 | local_irq_restore(flags); |
| 1960 | return 0; |
| 1961 | } |
| 1962 | |
| 1963 | static int lapic_resume(struct sys_device *dev) |
| 1964 | { |
| 1965 | unsigned int l, h; |
| 1966 | unsigned long flags; |
| 1967 | int maxlvt; |
| 1968 | |
| 1969 | if (!apic_pm_state.active) |
| 1970 | return 0; |
| 1971 | |
| 1972 | maxlvt = lapic_get_maxlvt(); |
| 1973 | |
| 1974 | local_irq_save(flags); |
| 1975 | |
| 1976 | #ifdef HAVE_X2APIC |
| 1977 | if (x2apic) |
| 1978 | enable_x2apic(); |
| 1979 | else |
| 1980 | #endif |
| 1981 | { |
| 1982 | /* |
| 1983 | * Make sure the APICBASE points to the right address |
| 1984 | * |
| 1985 | * FIXME! This will be wrong if we ever support suspend on |
| 1986 | * SMP! We'll need to do this as part of the CPU restore! |
| 1987 | */ |
| 1988 | rdmsr(MSR_IA32_APICBASE, l, h); |
| 1989 | l &= ~MSR_IA32_APICBASE_BASE; |
| 1990 | l |= MSR_IA32_APICBASE_ENABLE | mp_lapic_addr; |
| 1991 | wrmsr(MSR_IA32_APICBASE, l, h); |
| 1992 | } |
| 1993 | |
| 1994 | apic_write(APIC_LVTERR, ERROR_APIC_VECTOR | APIC_LVT_MASKED); |
| 1995 | apic_write(APIC_ID, apic_pm_state.apic_id); |
| 1996 | apic_write(APIC_DFR, apic_pm_state.apic_dfr); |
| 1997 | apic_write(APIC_LDR, apic_pm_state.apic_ldr); |
| 1998 | apic_write(APIC_TASKPRI, apic_pm_state.apic_taskpri); |
| 1999 | apic_write(APIC_SPIV, apic_pm_state.apic_spiv); |
| 2000 | apic_write(APIC_LVT0, apic_pm_state.apic_lvt0); |
| 2001 | apic_write(APIC_LVT1, apic_pm_state.apic_lvt1); |
| 2002 | #if defined(CONFIG_X86_MCE_P4THERMAL) || defined(CONFIG_X86_MCE_INTEL) |
| 2003 | if (maxlvt >= 5) |
| 2004 | apic_write(APIC_LVTTHMR, apic_pm_state.apic_thmr); |
| 2005 | #endif |
| 2006 | if (maxlvt >= 4) |
| 2007 | apic_write(APIC_LVTPC, apic_pm_state.apic_lvtpc); |
| 2008 | apic_write(APIC_LVTT, apic_pm_state.apic_lvtt); |
| 2009 | apic_write(APIC_TDCR, apic_pm_state.apic_tdcr); |
| 2010 | apic_write(APIC_TMICT, apic_pm_state.apic_tmict); |
| 2011 | apic_write(APIC_ESR, 0); |
| 2012 | apic_read(APIC_ESR); |
| 2013 | apic_write(APIC_LVTERR, apic_pm_state.apic_lvterr); |
| 2014 | apic_write(APIC_ESR, 0); |
| 2015 | apic_read(APIC_ESR); |
| 2016 | |
| 2017 | local_irq_restore(flags); |
| 2018 | |
| 2019 | return 0; |
| 2020 | } |
| 2021 | |
| 2022 | /* |
| 2023 | * This device has no shutdown method - fully functioning local APICs |
| 2024 | * are needed on every CPU up until machine_halt/restart/poweroff. |
| 2025 | */ |
| 2026 | |
| 2027 | static struct sysdev_class lapic_sysclass = { |
| 2028 | .name = "lapic", |
| 2029 | .resume = lapic_resume, |
| 2030 | .suspend = lapic_suspend, |
| 2031 | }; |
| 2032 | |
| 2033 | static struct sys_device device_lapic = { |
| 2034 | .id = 0, |
| 2035 | .cls = &lapic_sysclass, |
| 2036 | }; |
| 2037 | |
| 2038 | static void __cpuinit apic_pm_activate(void) |
| 2039 | { |
| 2040 | apic_pm_state.active = 1; |
| 2041 | } |
| 2042 | |
| 2043 | static int __init init_lapic_sysfs(void) |
| 2044 | { |
| 2045 | int error; |
| 2046 | |
| 2047 | if (!cpu_has_apic) |
| 2048 | return 0; |
| 2049 | /* XXX: remove suspend/resume procs if !apic_pm_state.active? */ |
| 2050 | |
| 2051 | error = sysdev_class_register(&lapic_sysclass); |
| 2052 | if (!error) |
| 2053 | error = sysdev_register(&device_lapic); |
| 2054 | return error; |
| 2055 | } |
| 2056 | device_initcall(init_lapic_sysfs); |
| 2057 | |
| 2058 | #else /* CONFIG_PM */ |
| 2059 | |
| 2060 | static void apic_pm_activate(void) { } |
| 2061 | |
| 2062 | #endif /* CONFIG_PM */ |
| 2063 | |
| 2064 | #ifdef CONFIG_X86_64 |
| 2065 | /* |
| 2066 | * apic_is_clustered_box() -- Check if we can expect good TSC |
| 2067 | * |
| 2068 | * Thus far, the major user of this is IBM's Summit2 series: |
| 2069 | * |
| 2070 | * Clustered boxes may have unsynced TSC problems if they are |
| 2071 | * multi-chassis. Use available data to take a good guess. |
| 2072 | * If in doubt, go HPET. |
| 2073 | */ |
| 2074 | __cpuinit int apic_is_clustered_box(void) |
| 2075 | { |
| 2076 | int i, clusters, zeros; |
| 2077 | unsigned id; |
| 2078 | u16 *bios_cpu_apicid; |
| 2079 | DECLARE_BITMAP(clustermap, NUM_APIC_CLUSTERS); |
| 2080 | |
| 2081 | /* |
| 2082 | * there is not this kind of box with AMD CPU yet. |
| 2083 | * Some AMD box with quadcore cpu and 8 sockets apicid |
| 2084 | * will be [4, 0x23] or [8, 0x27] could be thought to |
| 2085 | * vsmp box still need checking... |
| 2086 | */ |
| 2087 | if ((boot_cpu_data.x86_vendor == X86_VENDOR_AMD) && !is_vsmp_box()) |
| 2088 | return 0; |
| 2089 | |
| 2090 | bios_cpu_apicid = early_per_cpu_ptr(x86_bios_cpu_apicid); |
| 2091 | bitmap_zero(clustermap, NUM_APIC_CLUSTERS); |
| 2092 | |
| 2093 | for (i = 0; i < NR_CPUS; i++) { |
| 2094 | /* are we being called early in kernel startup? */ |
| 2095 | if (bios_cpu_apicid) { |
| 2096 | id = bios_cpu_apicid[i]; |
| 2097 | } |
| 2098 | else if (i < nr_cpu_ids) { |
| 2099 | if (cpu_present(i)) |
| 2100 | id = per_cpu(x86_bios_cpu_apicid, i); |
| 2101 | else |
| 2102 | continue; |
| 2103 | } |
| 2104 | else |
| 2105 | break; |
| 2106 | |
| 2107 | if (id != BAD_APICID) |
| 2108 | __set_bit(APIC_CLUSTERID(id), clustermap); |
| 2109 | } |
| 2110 | |
| 2111 | /* Problem: Partially populated chassis may not have CPUs in some of |
| 2112 | * the APIC clusters they have been allocated. Only present CPUs have |
| 2113 | * x86_bios_cpu_apicid entries, thus causing zeroes in the bitmap. |
| 2114 | * Since clusters are allocated sequentially, count zeros only if |
| 2115 | * they are bounded by ones. |
| 2116 | */ |
| 2117 | clusters = 0; |
| 2118 | zeros = 0; |
| 2119 | for (i = 0; i < NUM_APIC_CLUSTERS; i++) { |
| 2120 | if (test_bit(i, clustermap)) { |
| 2121 | clusters += 1 + zeros; |
| 2122 | zeros = 0; |
| 2123 | } else |
| 2124 | ++zeros; |
| 2125 | } |
| 2126 | |
| 2127 | /* ScaleMP vSMPowered boxes have one cluster per board and TSCs are |
| 2128 | * not guaranteed to be synced between boards |
| 2129 | */ |
| 2130 | if (is_vsmp_box() && clusters > 1) |
| 2131 | return 1; |
| 2132 | |
| 2133 | /* |
| 2134 | * If clusters > 2, then should be multi-chassis. |
| 2135 | * May have to revisit this when multi-core + hyperthreaded CPUs come |
| 2136 | * out, but AFAIK this will work even for them. |
| 2137 | */ |
| 2138 | return (clusters > 2); |
| 2139 | } |
| 2140 | #endif |
| 2141 | |
| 2142 | /* |
| 2143 | * APIC command line parameters |
| 2144 | */ |
| 2145 | static int __init setup_disableapic(char *arg) |
| 2146 | { |
| 2147 | disable_apic = 1; |
| 2148 | setup_clear_cpu_cap(X86_FEATURE_APIC); |
| 2149 | return 0; |
| 2150 | } |
| 2151 | early_param("disableapic", setup_disableapic); |
| 2152 | |
| 2153 | /* same as disableapic, for compatibility */ |
| 2154 | static int __init setup_nolapic(char *arg) |
| 2155 | { |
| 2156 | return setup_disableapic(arg); |
| 2157 | } |
| 2158 | early_param("nolapic", setup_nolapic); |
| 2159 | |
| 2160 | static int __init parse_lapic_timer_c2_ok(char *arg) |
| 2161 | { |
| 2162 | local_apic_timer_c2_ok = 1; |
| 2163 | return 0; |
| 2164 | } |
| 2165 | early_param("lapic_timer_c2_ok", parse_lapic_timer_c2_ok); |
| 2166 | |
| 2167 | static int __init parse_disable_apic_timer(char *arg) |
| 2168 | { |
| 2169 | disable_apic_timer = 1; |
| 2170 | return 0; |
| 2171 | } |
| 2172 | early_param("noapictimer", parse_disable_apic_timer); |
| 2173 | |
| 2174 | static int __init parse_nolapic_timer(char *arg) |
| 2175 | { |
| 2176 | disable_apic_timer = 1; |
| 2177 | return 0; |
| 2178 | } |
| 2179 | early_param("nolapic_timer", parse_nolapic_timer); |
| 2180 | |
| 2181 | static int __init apic_set_verbosity(char *arg) |
| 2182 | { |
| 2183 | if (!arg) { |
| 2184 | #ifdef CONFIG_X86_64 |
| 2185 | skip_ioapic_setup = 0; |
| 2186 | return 0; |
| 2187 | #endif |
| 2188 | return -EINVAL; |
| 2189 | } |
| 2190 | |
| 2191 | if (strcmp("debug", arg) == 0) |
| 2192 | apic_verbosity = APIC_DEBUG; |
| 2193 | else if (strcmp("verbose", arg) == 0) |
| 2194 | apic_verbosity = APIC_VERBOSE; |
| 2195 | else { |
| 2196 | printk(KERN_WARNING "APIC Verbosity level %s not recognised" |
| 2197 | " use apic=verbose or apic=debug\n", arg); |
| 2198 | return -EINVAL; |
| 2199 | } |
| 2200 | |
| 2201 | return 0; |
| 2202 | } |
| 2203 | early_param("apic", apic_set_verbosity); |
| 2204 | |
| 2205 | static int __init lapic_insert_resource(void) |
| 2206 | { |
| 2207 | if (!apic_phys) |
| 2208 | return -1; |
| 2209 | |
| 2210 | /* Put local APIC into the resource map. */ |
| 2211 | lapic_resource.start = apic_phys; |
| 2212 | lapic_resource.end = lapic_resource.start + PAGE_SIZE - 1; |
| 2213 | insert_resource(&iomem_resource, &lapic_resource); |
| 2214 | |
| 2215 | return 0; |
| 2216 | } |
| 2217 | |
| 2218 | /* |
| 2219 | * need call insert after e820_reserve_resources() |
| 2220 | * that is using request_resource |
| 2221 | */ |
| 2222 | late_initcall(lapic_insert_resource); |