| 1 | /* |
| 2 | * This is a good place to put board specific reboot fixups. |
| 3 | * |
| 4 | * List of supported fixups: |
| 5 | * geode-gx1/cs5530a - Jaya Kumar <jayalk@intworks.biz> |
| 6 | * geode-gx/lx/cs5536 - Andres Salomon <dilinger@debian.org> |
| 7 | * |
| 8 | */ |
| 9 | |
| 10 | #include <asm/delay.h> |
| 11 | #include <linux/pci.h> |
| 12 | #include <linux/interrupt.h> |
| 13 | #include <asm/reboot_fixups.h> |
| 14 | #include <asm/msr.h> |
| 15 | #include <asm/geode.h> |
| 16 | |
| 17 | static void cs5530a_warm_reset(struct pci_dev *dev) |
| 18 | { |
| 19 | /* writing 1 to the reset control register, 0x44 causes the |
| 20 | cs5530a to perform a system warm reset */ |
| 21 | pci_write_config_byte(dev, 0x44, 0x1); |
| 22 | udelay(50); /* shouldn't get here but be safe and spin-a-while */ |
| 23 | return; |
| 24 | } |
| 25 | |
| 26 | static void cs5536_warm_reset(struct pci_dev *dev) |
| 27 | { |
| 28 | /* writing 1 to the LSB of this MSR causes a hard reset */ |
| 29 | wrmsrl(MSR_DIVIL_SOFT_RESET, 1ULL); |
| 30 | udelay(50); /* shouldn't get here but be safe and spin a while */ |
| 31 | } |
| 32 | |
| 33 | struct device_fixup { |
| 34 | unsigned int vendor; |
| 35 | unsigned int device; |
| 36 | void (*reboot_fixup)(struct pci_dev *); |
| 37 | }; |
| 38 | |
| 39 | static struct device_fixup fixups_table[] = { |
| 40 | { PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY, cs5530a_warm_reset }, |
| 41 | { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, cs5536_warm_reset }, |
| 42 | { PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SC1100_BRIDGE, cs5530a_warm_reset }, |
| 43 | }; |
| 44 | |
| 45 | /* |
| 46 | * we see if any fixup is available for our current hardware. if there |
| 47 | * is a fixup, we call it and we expect to never return from it. if we |
| 48 | * do return, we keep looking and then eventually fall back to the |
| 49 | * standard mach_reboot on return. |
| 50 | */ |
| 51 | void mach_reboot_fixups(void) |
| 52 | { |
| 53 | struct device_fixup *cur; |
| 54 | struct pci_dev *dev; |
| 55 | int i; |
| 56 | |
| 57 | /* we can be called from sysrq-B code. In such a case it is |
| 58 | * prohibited to dig PCI */ |
| 59 | if (in_interrupt()) |
| 60 | return; |
| 61 | |
| 62 | for (i=0; i < ARRAY_SIZE(fixups_table); i++) { |
| 63 | cur = &(fixups_table[i]); |
| 64 | dev = pci_get_device(cur->vendor, cur->device, NULL); |
| 65 | if (!dev) |
| 66 | continue; |
| 67 | |
| 68 | cur->reboot_fixup(dev); |
| 69 | } |
| 70 | } |
| 71 | |