| 1 | /* |
| 2 | handle em28xx IR remotes via linux kernel input layer. |
| 3 | |
| 4 | Copyright (C) 2005 Ludovico Cavedon <cavedon@sssup.it> |
| 5 | Markus Rechberger <mrechberger@gmail.com> |
| 6 | Mauro Carvalho Chehab <mchehab@infradead.org> |
| 7 | Sascha Sommer <saschasommer@freenet.de> |
| 8 | |
| 9 | This program is free software; you can redistribute it and/or modify |
| 10 | it under the terms of the GNU General Public License as published by |
| 11 | the Free Software Foundation; either version 2 of the License, or |
| 12 | (at your option) any later version. |
| 13 | |
| 14 | This program is distributed in the hope that it will be useful, |
| 15 | but WITHOUT ANY WARRANTY; without even the implied warranty of |
| 16 | MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| 17 | GNU General Public License for more details. |
| 18 | |
| 19 | You should have received a copy of the GNU General Public License |
| 20 | along with this program; if not, write to the Free Software |
| 21 | Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA |
| 22 | */ |
| 23 | |
| 24 | #include <linux/module.h> |
| 25 | #include <linux/init.h> |
| 26 | #include <linux/delay.h> |
| 27 | #include <linux/interrupt.h> |
| 28 | #include <linux/usb.h> |
| 29 | #include <linux/slab.h> |
| 30 | |
| 31 | #include "em28xx.h" |
| 32 | |
| 33 | #define EM28XX_SNAPSHOT_KEY KEY_CAMERA |
| 34 | #define EM28XX_BUTTONS_DEBOUNCED_QUERY_INTERVAL 500 /* [ms] */ |
| 35 | #define EM28XX_BUTTONS_VOLATILE_QUERY_INTERVAL 100 /* [ms] */ |
| 36 | |
| 37 | static unsigned int ir_debug; |
| 38 | module_param(ir_debug, int, 0644); |
| 39 | MODULE_PARM_DESC(ir_debug, "enable debug messages [IR]"); |
| 40 | |
| 41 | #define MODULE_NAME "em28xx" |
| 42 | |
| 43 | #define dprintk(fmt, arg...) \ |
| 44 | if (ir_debug) { \ |
| 45 | printk(KERN_DEBUG "%s/ir: " fmt, ir->name , ## arg); \ |
| 46 | } |
| 47 | |
| 48 | /********************************************************** |
| 49 | Polling structure used by em28xx IR's |
| 50 | **********************************************************/ |
| 51 | |
| 52 | struct em28xx_ir_poll_result { |
| 53 | unsigned int toggle_bit:1; |
| 54 | unsigned int read_count:7; |
| 55 | |
| 56 | u32 scancode; |
| 57 | }; |
| 58 | |
| 59 | struct em28xx_IR { |
| 60 | struct em28xx *dev; |
| 61 | struct rc_dev *rc; |
| 62 | char name[32]; |
| 63 | char phys[32]; |
| 64 | |
| 65 | /* poll decoder */ |
| 66 | int polling; |
| 67 | struct delayed_work work; |
| 68 | unsigned int full_code:1; |
| 69 | unsigned int last_readcount; |
| 70 | u64 rc_type; |
| 71 | |
| 72 | /* i2c slave address of external device (if used) */ |
| 73 | u16 i2c_dev_addr; |
| 74 | |
| 75 | int (*get_key_i2c)(struct i2c_client *, u32 *); |
| 76 | int (*get_key)(struct em28xx_IR *, struct em28xx_ir_poll_result *); |
| 77 | }; |
| 78 | |
| 79 | /********************************************************** |
| 80 | I2C IR based get keycodes - should be used with ir-kbd-i2c |
| 81 | **********************************************************/ |
| 82 | |
| 83 | static int em28xx_get_key_terratec(struct i2c_client *i2c_dev, u32 *ir_key) |
| 84 | { |
| 85 | unsigned char b; |
| 86 | |
| 87 | /* poll IR chip */ |
| 88 | if (1 != i2c_master_recv(i2c_dev, &b, 1)) |
| 89 | return -EIO; |
| 90 | |
| 91 | /* it seems that 0xFE indicates that a button is still hold |
| 92 | down, while 0xff indicates that no button is hold down. */ |
| 93 | |
| 94 | if (b == 0xff) |
| 95 | return 0; |
| 96 | |
| 97 | if (b == 0xfe) |
| 98 | /* keep old data */ |
| 99 | return 1; |
| 100 | |
| 101 | *ir_key = b; |
| 102 | return 1; |
| 103 | } |
| 104 | |
| 105 | static int em28xx_get_key_em_haup(struct i2c_client *i2c_dev, u32 *ir_key) |
| 106 | { |
| 107 | unsigned char buf[2]; |
| 108 | u16 code; |
| 109 | int size; |
| 110 | |
| 111 | /* poll IR chip */ |
| 112 | size = i2c_master_recv(i2c_dev, buf, sizeof(buf)); |
| 113 | |
| 114 | if (size != 2) |
| 115 | return -EIO; |
| 116 | |
| 117 | /* Does eliminate repeated parity code */ |
| 118 | if (buf[1] == 0xff) |
| 119 | return 0; |
| 120 | |
| 121 | /* |
| 122 | * Rearranges bits to the right order. |
| 123 | * The bit order were determined experimentally by using |
| 124 | * The original Hauppauge Grey IR and another RC5 that uses addr=0x08 |
| 125 | * The RC5 code has 14 bits, but we've experimentally determined |
| 126 | * the meaning for only 11 bits. |
| 127 | * So, the code translation is not complete. Yet, it is enough to |
| 128 | * work with the provided RC5 IR. |
| 129 | */ |
| 130 | code = |
| 131 | ((buf[0] & 0x01) ? 0x0020 : 0) | /* 0010 0000 */ |
| 132 | ((buf[0] & 0x02) ? 0x0010 : 0) | /* 0001 0000 */ |
| 133 | ((buf[0] & 0x04) ? 0x0008 : 0) | /* 0000 1000 */ |
| 134 | ((buf[0] & 0x08) ? 0x0004 : 0) | /* 0000 0100 */ |
| 135 | ((buf[0] & 0x10) ? 0x0002 : 0) | /* 0000 0010 */ |
| 136 | ((buf[0] & 0x20) ? 0x0001 : 0) | /* 0000 0001 */ |
| 137 | ((buf[1] & 0x08) ? 0x1000 : 0) | /* 0001 0000 */ |
| 138 | ((buf[1] & 0x10) ? 0x0800 : 0) | /* 0000 1000 */ |
| 139 | ((buf[1] & 0x20) ? 0x0400 : 0) | /* 0000 0100 */ |
| 140 | ((buf[1] & 0x40) ? 0x0200 : 0) | /* 0000 0010 */ |
| 141 | ((buf[1] & 0x80) ? 0x0100 : 0); /* 0000 0001 */ |
| 142 | |
| 143 | /* return key */ |
| 144 | *ir_key = code; |
| 145 | return 1; |
| 146 | } |
| 147 | |
| 148 | static int em28xx_get_key_pinnacle_usb_grey(struct i2c_client *i2c_dev, |
| 149 | u32 *ir_key) |
| 150 | { |
| 151 | unsigned char buf[3]; |
| 152 | |
| 153 | /* poll IR chip */ |
| 154 | |
| 155 | if (3 != i2c_master_recv(i2c_dev, buf, 3)) |
| 156 | return -EIO; |
| 157 | |
| 158 | if (buf[0] != 0x00) |
| 159 | return 0; |
| 160 | |
| 161 | *ir_key = buf[2]&0x3f; |
| 162 | |
| 163 | return 1; |
| 164 | } |
| 165 | |
| 166 | static int em28xx_get_key_winfast_usbii_deluxe(struct i2c_client *i2c_dev, |
| 167 | u32 *ir_key) |
| 168 | { |
| 169 | unsigned char subaddr, keydetect, key; |
| 170 | |
| 171 | struct i2c_msg msg[] = { { .addr = i2c_dev->addr, .flags = 0, .buf = &subaddr, .len = 1}, |
| 172 | { .addr = i2c_dev->addr, .flags = I2C_M_RD, .buf = &keydetect, .len = 1} }; |
| 173 | |
| 174 | subaddr = 0x10; |
| 175 | if (2 != i2c_transfer(i2c_dev->adapter, msg, 2)) |
| 176 | return -EIO; |
| 177 | if (keydetect == 0x00) |
| 178 | return 0; |
| 179 | |
| 180 | subaddr = 0x00; |
| 181 | msg[1].buf = &key; |
| 182 | if (2 != i2c_transfer(i2c_dev->adapter, msg, 2)) |
| 183 | return -EIO; |
| 184 | if (key == 0x00) |
| 185 | return 0; |
| 186 | |
| 187 | *ir_key = key; |
| 188 | return 1; |
| 189 | } |
| 190 | |
| 191 | /********************************************************** |
| 192 | Poll based get keycode functions |
| 193 | **********************************************************/ |
| 194 | |
| 195 | /* This is for the em2860/em2880 */ |
| 196 | static int default_polling_getkey(struct em28xx_IR *ir, |
| 197 | struct em28xx_ir_poll_result *poll_result) |
| 198 | { |
| 199 | struct em28xx *dev = ir->dev; |
| 200 | int rc; |
| 201 | u8 msg[3] = { 0, 0, 0 }; |
| 202 | |
| 203 | /* Read key toggle, brand, and key code |
| 204 | on registers 0x45, 0x46 and 0x47 |
| 205 | */ |
| 206 | rc = dev->em28xx_read_reg_req_len(dev, 0, EM28XX_R45_IR, |
| 207 | msg, sizeof(msg)); |
| 208 | if (rc < 0) |
| 209 | return rc; |
| 210 | |
| 211 | /* Infrared toggle (Reg 0x45[7]) */ |
| 212 | poll_result->toggle_bit = (msg[0] >> 7); |
| 213 | |
| 214 | /* Infrared read count (Reg 0x45[6:0] */ |
| 215 | poll_result->read_count = (msg[0] & 0x7f); |
| 216 | |
| 217 | /* Remote Control Address/Data (Regs 0x46/0x47) */ |
| 218 | poll_result->scancode = msg[1] << 8 | msg[2]; |
| 219 | |
| 220 | return 0; |
| 221 | } |
| 222 | |
| 223 | static int em2874_polling_getkey(struct em28xx_IR *ir, |
| 224 | struct em28xx_ir_poll_result *poll_result) |
| 225 | { |
| 226 | struct em28xx *dev = ir->dev; |
| 227 | int rc; |
| 228 | u8 msg[5] = { 0, 0, 0, 0, 0 }; |
| 229 | |
| 230 | /* Read key toggle, brand, and key code |
| 231 | on registers 0x51-55 |
| 232 | */ |
| 233 | rc = dev->em28xx_read_reg_req_len(dev, 0, EM2874_R51_IR, |
| 234 | msg, sizeof(msg)); |
| 235 | if (rc < 0) |
| 236 | return rc; |
| 237 | |
| 238 | /* Infrared toggle (Reg 0x51[7]) */ |
| 239 | poll_result->toggle_bit = (msg[0] >> 7); |
| 240 | |
| 241 | /* Infrared read count (Reg 0x51[6:0] */ |
| 242 | poll_result->read_count = (msg[0] & 0x7f); |
| 243 | |
| 244 | /* |
| 245 | * Remote Control Address (Reg 0x52) |
| 246 | * Remote Control Data (Reg 0x53-0x55) |
| 247 | */ |
| 248 | switch (ir->rc_type) { |
| 249 | case RC_BIT_RC5: |
| 250 | poll_result->scancode = msg[1] << 8 | msg[2]; |
| 251 | break; |
| 252 | case RC_BIT_NEC: |
| 253 | if ((msg[3] ^ msg[4]) != 0xff) /* 32 bits NEC */ |
| 254 | poll_result->scancode = (msg[1] << 24) | |
| 255 | (msg[2] << 16) | |
| 256 | (msg[3] << 8) | |
| 257 | msg[4]; |
| 258 | else if ((msg[1] ^ msg[2]) != 0xff) /* 24 bits NEC */ |
| 259 | poll_result->scancode = (msg[1] << 16) | |
| 260 | (msg[2] << 8) | |
| 261 | msg[3]; |
| 262 | else /* Normal NEC */ |
| 263 | poll_result->scancode = msg[1] << 8 | msg[3]; |
| 264 | break; |
| 265 | case RC_BIT_RC6_0: |
| 266 | poll_result->scancode = msg[1] << 8 | msg[2]; |
| 267 | break; |
| 268 | default: |
| 269 | poll_result->scancode = (msg[1] << 24) | (msg[2] << 16) | |
| 270 | (msg[3] << 8) | msg[4]; |
| 271 | break; |
| 272 | } |
| 273 | |
| 274 | return 0; |
| 275 | } |
| 276 | |
| 277 | /********************************************************** |
| 278 | Polling code for em28xx |
| 279 | **********************************************************/ |
| 280 | |
| 281 | static int em28xx_i2c_ir_handle_key(struct em28xx_IR *ir) |
| 282 | { |
| 283 | struct em28xx *dev = ir->dev; |
| 284 | static u32 ir_key; |
| 285 | int rc; |
| 286 | struct i2c_client client; |
| 287 | |
| 288 | client.adapter = &ir->dev->i2c_adap[dev->def_i2c_bus]; |
| 289 | client.addr = ir->i2c_dev_addr; |
| 290 | |
| 291 | rc = ir->get_key_i2c(&client, &ir_key); |
| 292 | if (rc < 0) { |
| 293 | dprintk("ir->get_key_i2c() failed: %d\n", rc); |
| 294 | return rc; |
| 295 | } |
| 296 | |
| 297 | if (rc) { |
| 298 | dprintk("%s: keycode = 0x%04x\n", __func__, ir_key); |
| 299 | rc_keydown(ir->rc, ir_key, 0); |
| 300 | } |
| 301 | return 0; |
| 302 | } |
| 303 | |
| 304 | static void em28xx_ir_handle_key(struct em28xx_IR *ir) |
| 305 | { |
| 306 | int result; |
| 307 | struct em28xx_ir_poll_result poll_result; |
| 308 | |
| 309 | /* read the registers containing the IR status */ |
| 310 | result = ir->get_key(ir, &poll_result); |
| 311 | if (unlikely(result < 0)) { |
| 312 | dprintk("ir->get_key() failed: %d\n", result); |
| 313 | return; |
| 314 | } |
| 315 | |
| 316 | if (unlikely(poll_result.read_count != ir->last_readcount)) { |
| 317 | dprintk("%s: toggle: %d, count: %d, key 0x%04x\n", __func__, |
| 318 | poll_result.toggle_bit, poll_result.read_count, |
| 319 | poll_result.scancode); |
| 320 | if (ir->full_code) |
| 321 | rc_keydown(ir->rc, |
| 322 | poll_result.scancode, |
| 323 | poll_result.toggle_bit); |
| 324 | else |
| 325 | rc_keydown(ir->rc, |
| 326 | poll_result.scancode & 0xff, |
| 327 | poll_result.toggle_bit); |
| 328 | |
| 329 | if (ir->dev->chip_id == CHIP_ID_EM2874 || |
| 330 | ir->dev->chip_id == CHIP_ID_EM2884) |
| 331 | /* The em2874 clears the readcount field every time the |
| 332 | register is read. The em2860/2880 datasheet says that it |
| 333 | is supposed to clear the readcount, but it doesn't. So with |
| 334 | the em2874, we are looking for a non-zero read count as |
| 335 | opposed to a readcount that is incrementing */ |
| 336 | ir->last_readcount = 0; |
| 337 | else |
| 338 | ir->last_readcount = poll_result.read_count; |
| 339 | } |
| 340 | } |
| 341 | |
| 342 | static void em28xx_ir_work(struct work_struct *work) |
| 343 | { |
| 344 | struct em28xx_IR *ir = container_of(work, struct em28xx_IR, work.work); |
| 345 | |
| 346 | if (ir->i2c_dev_addr) /* external i2c device */ |
| 347 | em28xx_i2c_ir_handle_key(ir); |
| 348 | else /* internal device */ |
| 349 | em28xx_ir_handle_key(ir); |
| 350 | schedule_delayed_work(&ir->work, msecs_to_jiffies(ir->polling)); |
| 351 | } |
| 352 | |
| 353 | static int em28xx_ir_start(struct rc_dev *rc) |
| 354 | { |
| 355 | struct em28xx_IR *ir = rc->priv; |
| 356 | |
| 357 | INIT_DELAYED_WORK(&ir->work, em28xx_ir_work); |
| 358 | schedule_delayed_work(&ir->work, 0); |
| 359 | |
| 360 | return 0; |
| 361 | } |
| 362 | |
| 363 | static void em28xx_ir_stop(struct rc_dev *rc) |
| 364 | { |
| 365 | struct em28xx_IR *ir = rc->priv; |
| 366 | |
| 367 | cancel_delayed_work_sync(&ir->work); |
| 368 | } |
| 369 | |
| 370 | static int em2860_ir_change_protocol(struct rc_dev *rc_dev, u64 *rc_type) |
| 371 | { |
| 372 | struct em28xx_IR *ir = rc_dev->priv; |
| 373 | struct em28xx *dev = ir->dev; |
| 374 | |
| 375 | /* Adjust xclk based on IR table for RC5/NEC tables */ |
| 376 | if (*rc_type & RC_BIT_RC5) { |
| 377 | dev->board.xclk |= EM28XX_XCLK_IR_RC5_MODE; |
| 378 | ir->full_code = 1; |
| 379 | *rc_type = RC_BIT_RC5; |
| 380 | } else if (*rc_type & RC_BIT_NEC) { |
| 381 | dev->board.xclk &= ~EM28XX_XCLK_IR_RC5_MODE; |
| 382 | ir->full_code = 1; |
| 383 | *rc_type = RC_BIT_NEC; |
| 384 | } else if (*rc_type & RC_BIT_UNKNOWN) { |
| 385 | *rc_type = RC_BIT_UNKNOWN; |
| 386 | } else { |
| 387 | *rc_type = ir->rc_type; |
| 388 | return -EINVAL; |
| 389 | } |
| 390 | em28xx_write_reg_bits(dev, EM28XX_R0F_XCLK, dev->board.xclk, |
| 391 | EM28XX_XCLK_IR_RC5_MODE); |
| 392 | |
| 393 | ir->rc_type = *rc_type; |
| 394 | |
| 395 | return 0; |
| 396 | } |
| 397 | |
| 398 | static int em2874_ir_change_protocol(struct rc_dev *rc_dev, u64 *rc_type) |
| 399 | { |
| 400 | struct em28xx_IR *ir = rc_dev->priv; |
| 401 | struct em28xx *dev = ir->dev; |
| 402 | u8 ir_config = EM2874_IR_RC5; |
| 403 | |
| 404 | /* Adjust xclk and set type based on IR table for RC5/NEC/RC6 tables */ |
| 405 | if (*rc_type & RC_BIT_RC5) { |
| 406 | dev->board.xclk |= EM28XX_XCLK_IR_RC5_MODE; |
| 407 | ir->full_code = 1; |
| 408 | *rc_type = RC_BIT_RC5; |
| 409 | } else if (*rc_type & RC_BIT_NEC) { |
| 410 | dev->board.xclk &= ~EM28XX_XCLK_IR_RC5_MODE; |
| 411 | ir_config = EM2874_IR_NEC | EM2874_IR_NEC_NO_PARITY; |
| 412 | ir->full_code = 1; |
| 413 | *rc_type = RC_BIT_NEC; |
| 414 | } else if (*rc_type & RC_BIT_RC6_0) { |
| 415 | dev->board.xclk |= EM28XX_XCLK_IR_RC5_MODE; |
| 416 | ir_config = EM2874_IR_RC6_MODE_0; |
| 417 | ir->full_code = 1; |
| 418 | *rc_type = RC_BIT_RC6_0; |
| 419 | } else if (*rc_type & RC_BIT_UNKNOWN) { |
| 420 | *rc_type = RC_BIT_UNKNOWN; |
| 421 | } else { |
| 422 | *rc_type = ir->rc_type; |
| 423 | return -EINVAL; |
| 424 | } |
| 425 | em28xx_write_regs(dev, EM2874_R50_IR_CONFIG, &ir_config, 1); |
| 426 | em28xx_write_reg_bits(dev, EM28XX_R0F_XCLK, dev->board.xclk, |
| 427 | EM28XX_XCLK_IR_RC5_MODE); |
| 428 | |
| 429 | ir->rc_type = *rc_type; |
| 430 | |
| 431 | return 0; |
| 432 | } |
| 433 | static int em28xx_ir_change_protocol(struct rc_dev *rc_dev, u64 *rc_type) |
| 434 | { |
| 435 | struct em28xx_IR *ir = rc_dev->priv; |
| 436 | struct em28xx *dev = ir->dev; |
| 437 | |
| 438 | /* Setup the proper handler based on the chip */ |
| 439 | switch (dev->chip_id) { |
| 440 | case CHIP_ID_EM2860: |
| 441 | case CHIP_ID_EM2883: |
| 442 | return em2860_ir_change_protocol(rc_dev, rc_type); |
| 443 | case CHIP_ID_EM2884: |
| 444 | case CHIP_ID_EM2874: |
| 445 | case CHIP_ID_EM28174: |
| 446 | case CHIP_ID_EM28178: |
| 447 | return em2874_ir_change_protocol(rc_dev, rc_type); |
| 448 | default: |
| 449 | printk("Unrecognized em28xx chip id 0x%02x: IR not supported\n", |
| 450 | dev->chip_id); |
| 451 | return -EINVAL; |
| 452 | } |
| 453 | } |
| 454 | |
| 455 | static int em28xx_probe_i2c_ir(struct em28xx *dev) |
| 456 | { |
| 457 | int i = 0; |
| 458 | /* Leadtek winfast tv USBII deluxe can find a non working IR-device */ |
| 459 | /* at address 0x18, so if that address is needed for another board in */ |
| 460 | /* the future, please put it after 0x1f. */ |
| 461 | const unsigned short addr_list[] = { |
| 462 | 0x1f, 0x30, 0x47, I2C_CLIENT_END |
| 463 | }; |
| 464 | |
| 465 | while (addr_list[i] != I2C_CLIENT_END) { |
| 466 | if (i2c_probe_func_quick_read(&dev->i2c_adap[dev->def_i2c_bus], addr_list[i]) == 1) |
| 467 | return addr_list[i]; |
| 468 | i++; |
| 469 | } |
| 470 | |
| 471 | return -ENODEV; |
| 472 | } |
| 473 | |
| 474 | /********************************************************** |
| 475 | Handle buttons |
| 476 | **********************************************************/ |
| 477 | |
| 478 | static void em28xx_query_buttons(struct work_struct *work) |
| 479 | { |
| 480 | struct em28xx *dev = |
| 481 | container_of(work, struct em28xx, buttons_query_work.work); |
| 482 | u8 i, j; |
| 483 | int regval; |
| 484 | bool is_pressed, was_pressed; |
| 485 | const struct em28xx_led *led; |
| 486 | |
| 487 | /* Poll and evaluate all addresses */ |
| 488 | for (i = 0; i < dev->num_button_polling_addresses; i++) { |
| 489 | /* Read value from register */ |
| 490 | regval = em28xx_read_reg(dev, dev->button_polling_addresses[i]); |
| 491 | if (regval < 0) |
| 492 | continue; |
| 493 | /* Check states of the buttons and act */ |
| 494 | j = 0; |
| 495 | while (dev->board.buttons[j].role >= 0 && |
| 496 | dev->board.buttons[j].role < EM28XX_NUM_BUTTON_ROLES) { |
| 497 | struct em28xx_button *button = &dev->board.buttons[j]; |
| 498 | /* Check if button uses the current address */ |
| 499 | if (button->reg_r != dev->button_polling_addresses[i]) { |
| 500 | j++; |
| 501 | continue; |
| 502 | } |
| 503 | /* Determine if button is and was pressed last time */ |
| 504 | is_pressed = regval & button->mask; |
| 505 | was_pressed = dev->button_polling_last_values[i] |
| 506 | & button->mask; |
| 507 | if (button->inverted) { |
| 508 | is_pressed = !is_pressed; |
| 509 | was_pressed = !was_pressed; |
| 510 | } |
| 511 | /* Clear button state (if needed) */ |
| 512 | if (is_pressed && button->reg_clearing) |
| 513 | em28xx_write_reg(dev, button->reg_clearing, |
| 514 | (~regval & button->mask) |
| 515 | | (regval & ~button->mask)); |
| 516 | /* Handle button state */ |
| 517 | if (!is_pressed || was_pressed) { |
| 518 | j++; |
| 519 | continue; |
| 520 | } |
| 521 | switch (button->role) { |
| 522 | case EM28XX_BUTTON_SNAPSHOT: |
| 523 | /* Emulate the keypress */ |
| 524 | input_report_key(dev->sbutton_input_dev, |
| 525 | EM28XX_SNAPSHOT_KEY, 1); |
| 526 | /* Unpress the key */ |
| 527 | input_report_key(dev->sbutton_input_dev, |
| 528 | EM28XX_SNAPSHOT_KEY, 0); |
| 529 | break; |
| 530 | case EM28XX_BUTTON_ILLUMINATION: |
| 531 | led = em28xx_find_led(dev, |
| 532 | EM28XX_LED_ILLUMINATION); |
| 533 | /* Switch illumination LED on/off */ |
| 534 | if (led) |
| 535 | em28xx_toggle_reg_bits(dev, |
| 536 | led->gpio_reg, |
| 537 | led->gpio_mask); |
| 538 | break; |
| 539 | default: |
| 540 | WARN_ONCE(1, "BUG: unhandled button role."); |
| 541 | } |
| 542 | /* Next button */ |
| 543 | j++; |
| 544 | } |
| 545 | /* Save current value for comparison during the next polling */ |
| 546 | dev->button_polling_last_values[i] = regval; |
| 547 | } |
| 548 | /* Schedule next poll */ |
| 549 | schedule_delayed_work(&dev->buttons_query_work, |
| 550 | msecs_to_jiffies(dev->button_polling_interval)); |
| 551 | } |
| 552 | |
| 553 | static int em28xx_register_snapshot_button(struct em28xx *dev) |
| 554 | { |
| 555 | struct input_dev *input_dev; |
| 556 | int err; |
| 557 | |
| 558 | em28xx_info("Registering snapshot button...\n"); |
| 559 | input_dev = input_allocate_device(); |
| 560 | if (!input_dev) { |
| 561 | em28xx_errdev("input_allocate_device failed\n"); |
| 562 | return -ENOMEM; |
| 563 | } |
| 564 | |
| 565 | usb_make_path(dev->udev, dev->snapshot_button_path, |
| 566 | sizeof(dev->snapshot_button_path)); |
| 567 | strlcat(dev->snapshot_button_path, "/sbutton", |
| 568 | sizeof(dev->snapshot_button_path)); |
| 569 | |
| 570 | input_dev->name = "em28xx snapshot button"; |
| 571 | input_dev->phys = dev->snapshot_button_path; |
| 572 | input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REP); |
| 573 | set_bit(EM28XX_SNAPSHOT_KEY, input_dev->keybit); |
| 574 | input_dev->keycodesize = 0; |
| 575 | input_dev->keycodemax = 0; |
| 576 | input_dev->id.bustype = BUS_USB; |
| 577 | input_dev->id.vendor = le16_to_cpu(dev->udev->descriptor.idVendor); |
| 578 | input_dev->id.product = le16_to_cpu(dev->udev->descriptor.idProduct); |
| 579 | input_dev->id.version = 1; |
| 580 | input_dev->dev.parent = &dev->udev->dev; |
| 581 | |
| 582 | err = input_register_device(input_dev); |
| 583 | if (err) { |
| 584 | em28xx_errdev("input_register_device failed\n"); |
| 585 | input_free_device(input_dev); |
| 586 | return err; |
| 587 | } |
| 588 | |
| 589 | dev->sbutton_input_dev = input_dev; |
| 590 | return 0; |
| 591 | } |
| 592 | |
| 593 | static void em28xx_init_buttons(struct em28xx *dev) |
| 594 | { |
| 595 | u8 i = 0, j = 0; |
| 596 | bool addr_new = 0; |
| 597 | |
| 598 | dev->button_polling_interval = EM28XX_BUTTONS_DEBOUNCED_QUERY_INTERVAL; |
| 599 | while (dev->board.buttons[i].role >= 0 && |
| 600 | dev->board.buttons[i].role < EM28XX_NUM_BUTTON_ROLES) { |
| 601 | struct em28xx_button *button = &dev->board.buttons[i]; |
| 602 | /* Check if polling address is already on the list */ |
| 603 | addr_new = 1; |
| 604 | for (j = 0; j < dev->num_button_polling_addresses; j++) { |
| 605 | if (button->reg_r == dev->button_polling_addresses[j]) { |
| 606 | addr_new = 0; |
| 607 | break; |
| 608 | } |
| 609 | } |
| 610 | /* Check if max. number of polling addresses is exceeded */ |
| 611 | if (addr_new && dev->num_button_polling_addresses |
| 612 | >= EM28XX_NUM_BUTTON_ADDRESSES_MAX) { |
| 613 | WARN_ONCE(1, "BUG: maximum number of button polling addresses exceeded."); |
| 614 | goto next_button; |
| 615 | } |
| 616 | /* Button role specific checks and actions */ |
| 617 | if (button->role == EM28XX_BUTTON_SNAPSHOT) { |
| 618 | /* Register input device */ |
| 619 | if (em28xx_register_snapshot_button(dev) < 0) |
| 620 | goto next_button; |
| 621 | } else if (button->role == EM28XX_BUTTON_ILLUMINATION) { |
| 622 | /* Check sanity */ |
| 623 | if (!em28xx_find_led(dev, EM28XX_LED_ILLUMINATION)) { |
| 624 | em28xx_errdev("BUG: illumination button defined, but no illumination LED.\n"); |
| 625 | goto next_button; |
| 626 | } |
| 627 | } |
| 628 | /* Add read address to list of polling addresses */ |
| 629 | if (addr_new) { |
| 630 | unsigned int index = dev->num_button_polling_addresses; |
| 631 | dev->button_polling_addresses[index] = button->reg_r; |
| 632 | dev->num_button_polling_addresses++; |
| 633 | } |
| 634 | /* Reduce polling interval if necessary */ |
| 635 | if (!button->reg_clearing) |
| 636 | dev->button_polling_interval = |
| 637 | EM28XX_BUTTONS_VOLATILE_QUERY_INTERVAL; |
| 638 | next_button: |
| 639 | /* Next button */ |
| 640 | i++; |
| 641 | } |
| 642 | |
| 643 | /* Start polling */ |
| 644 | if (dev->num_button_polling_addresses) { |
| 645 | memset(dev->button_polling_last_values, 0, |
| 646 | EM28XX_NUM_BUTTON_ADDRESSES_MAX); |
| 647 | INIT_DELAYED_WORK(&dev->buttons_query_work, |
| 648 | em28xx_query_buttons); |
| 649 | schedule_delayed_work(&dev->buttons_query_work, |
| 650 | msecs_to_jiffies(dev->button_polling_interval)); |
| 651 | } |
| 652 | } |
| 653 | |
| 654 | static void em28xx_shutdown_buttons(struct em28xx *dev) |
| 655 | { |
| 656 | /* Cancel polling */ |
| 657 | cancel_delayed_work_sync(&dev->buttons_query_work); |
| 658 | /* Clear polling addresses list */ |
| 659 | dev->num_button_polling_addresses = 0; |
| 660 | /* Deregister input devices */ |
| 661 | if (dev->sbutton_input_dev != NULL) { |
| 662 | em28xx_info("Deregistering snapshot button\n"); |
| 663 | input_unregister_device(dev->sbutton_input_dev); |
| 664 | dev->sbutton_input_dev = NULL; |
| 665 | } |
| 666 | } |
| 667 | |
| 668 | static int em28xx_ir_init(struct em28xx *dev) |
| 669 | { |
| 670 | struct em28xx_IR *ir; |
| 671 | struct rc_dev *rc; |
| 672 | int err = -ENOMEM; |
| 673 | u64 rc_type; |
| 674 | u16 i2c_rc_dev_addr = 0; |
| 675 | |
| 676 | if (dev->board.buttons) |
| 677 | em28xx_init_buttons(dev); |
| 678 | |
| 679 | if (dev->board.has_ir_i2c) { |
| 680 | i2c_rc_dev_addr = em28xx_probe_i2c_ir(dev); |
| 681 | if (!i2c_rc_dev_addr) { |
| 682 | dev->board.has_ir_i2c = 0; |
| 683 | em28xx_warn("No i2c IR remote control device found.\n"); |
| 684 | return -ENODEV; |
| 685 | } |
| 686 | } |
| 687 | |
| 688 | if (dev->board.ir_codes == NULL && !dev->board.has_ir_i2c) { |
| 689 | /* No remote control support */ |
| 690 | em28xx_warn("Remote control support is not available for " |
| 691 | "this card.\n"); |
| 692 | return 0; |
| 693 | } |
| 694 | |
| 695 | ir = kzalloc(sizeof(*ir), GFP_KERNEL); |
| 696 | rc = rc_allocate_device(); |
| 697 | if (!ir || !rc) |
| 698 | goto error; |
| 699 | |
| 700 | /* record handles to ourself */ |
| 701 | ir->dev = dev; |
| 702 | dev->ir = ir; |
| 703 | ir->rc = rc; |
| 704 | |
| 705 | rc->priv = ir; |
| 706 | rc->open = em28xx_ir_start; |
| 707 | rc->close = em28xx_ir_stop; |
| 708 | |
| 709 | if (dev->board.has_ir_i2c) { /* external i2c device */ |
| 710 | switch (dev->model) { |
| 711 | case EM2800_BOARD_TERRATEC_CINERGY_200: |
| 712 | case EM2820_BOARD_TERRATEC_CINERGY_250: |
| 713 | rc->map_name = RC_MAP_EM_TERRATEC; |
| 714 | ir->get_key_i2c = em28xx_get_key_terratec; |
| 715 | break; |
| 716 | case EM2820_BOARD_PINNACLE_USB_2: |
| 717 | rc->map_name = RC_MAP_PINNACLE_GREY; |
| 718 | ir->get_key_i2c = em28xx_get_key_pinnacle_usb_grey; |
| 719 | break; |
| 720 | case EM2820_BOARD_HAUPPAUGE_WINTV_USB_2: |
| 721 | rc->map_name = RC_MAP_HAUPPAUGE; |
| 722 | ir->get_key_i2c = em28xx_get_key_em_haup; |
| 723 | rc->allowed_protos = RC_BIT_RC5; |
| 724 | break; |
| 725 | case EM2820_BOARD_LEADTEK_WINFAST_USBII_DELUXE: |
| 726 | rc->map_name = RC_MAP_WINFAST_USBII_DELUXE; |
| 727 | ir->get_key_i2c = em28xx_get_key_winfast_usbii_deluxe; |
| 728 | break; |
| 729 | default: |
| 730 | err = -ENODEV; |
| 731 | goto error; |
| 732 | } |
| 733 | |
| 734 | ir->i2c_dev_addr = i2c_rc_dev_addr; |
| 735 | } else { /* internal device */ |
| 736 | switch (dev->chip_id) { |
| 737 | case CHIP_ID_EM2860: |
| 738 | case CHIP_ID_EM2883: |
| 739 | rc->allowed_protos = RC_BIT_RC5 | RC_BIT_NEC; |
| 740 | ir->get_key = default_polling_getkey; |
| 741 | break; |
| 742 | case CHIP_ID_EM2884: |
| 743 | case CHIP_ID_EM2874: |
| 744 | case CHIP_ID_EM28174: |
| 745 | case CHIP_ID_EM28178: |
| 746 | ir->get_key = em2874_polling_getkey; |
| 747 | rc->allowed_protos = RC_BIT_RC5 | RC_BIT_NEC | |
| 748 | RC_BIT_RC6_0; |
| 749 | break; |
| 750 | default: |
| 751 | err = -ENODEV; |
| 752 | goto error; |
| 753 | } |
| 754 | |
| 755 | rc->change_protocol = em28xx_ir_change_protocol; |
| 756 | rc->map_name = dev->board.ir_codes; |
| 757 | |
| 758 | /* By default, keep protocol field untouched */ |
| 759 | rc_type = RC_BIT_UNKNOWN; |
| 760 | err = em28xx_ir_change_protocol(rc, &rc_type); |
| 761 | if (err) |
| 762 | goto error; |
| 763 | } |
| 764 | |
| 765 | /* This is how often we ask the chip for IR information */ |
| 766 | ir->polling = 100; /* ms */ |
| 767 | |
| 768 | /* init input device */ |
| 769 | snprintf(ir->name, sizeof(ir->name), "em28xx IR (%s)", dev->name); |
| 770 | |
| 771 | usb_make_path(dev->udev, ir->phys, sizeof(ir->phys)); |
| 772 | strlcat(ir->phys, "/input0", sizeof(ir->phys)); |
| 773 | |
| 774 | rc->input_name = ir->name; |
| 775 | rc->input_phys = ir->phys; |
| 776 | rc->input_id.bustype = BUS_USB; |
| 777 | rc->input_id.version = 1; |
| 778 | rc->input_id.vendor = le16_to_cpu(dev->udev->descriptor.idVendor); |
| 779 | rc->input_id.product = le16_to_cpu(dev->udev->descriptor.idProduct); |
| 780 | rc->dev.parent = &dev->udev->dev; |
| 781 | rc->driver_name = MODULE_NAME; |
| 782 | |
| 783 | /* all done */ |
| 784 | err = rc_register_device(rc); |
| 785 | if (err) |
| 786 | goto error; |
| 787 | |
| 788 | return 0; |
| 789 | |
| 790 | error: |
| 791 | dev->ir = NULL; |
| 792 | rc_free_device(rc); |
| 793 | kfree(ir); |
| 794 | return err; |
| 795 | } |
| 796 | |
| 797 | static int em28xx_ir_fini(struct em28xx *dev) |
| 798 | { |
| 799 | struct em28xx_IR *ir = dev->ir; |
| 800 | |
| 801 | em28xx_shutdown_buttons(dev); |
| 802 | |
| 803 | /* skip detach on non attached boards */ |
| 804 | if (!ir) |
| 805 | return 0; |
| 806 | |
| 807 | if (ir->rc) |
| 808 | rc_unregister_device(ir->rc); |
| 809 | |
| 810 | /* done */ |
| 811 | kfree(ir); |
| 812 | dev->ir = NULL; |
| 813 | return 0; |
| 814 | } |
| 815 | |
| 816 | static struct em28xx_ops rc_ops = { |
| 817 | .id = EM28XX_RC, |
| 818 | .name = "Em28xx Input Extension", |
| 819 | .init = em28xx_ir_init, |
| 820 | .fini = em28xx_ir_fini, |
| 821 | }; |
| 822 | |
| 823 | static int __init em28xx_rc_register(void) |
| 824 | { |
| 825 | return em28xx_register_extension(&rc_ops); |
| 826 | } |
| 827 | |
| 828 | static void __exit em28xx_rc_unregister(void) |
| 829 | { |
| 830 | em28xx_unregister_extension(&rc_ops); |
| 831 | } |
| 832 | |
| 833 | MODULE_LICENSE("GPL"); |
| 834 | MODULE_AUTHOR("Mauro Carvalho Chehab <mchehab@redhat.com>"); |
| 835 | MODULE_DESCRIPTION("Em28xx Input driver"); |
| 836 | |
| 837 | module_init(em28xx_rc_register); |
| 838 | module_exit(em28xx_rc_unregister); |